An issue was discovered on Securifi Almond, Almond+, and Almond 2015 devices with firmware AL-R096. The device provides a user with the capability of adding new port forwarding rules to the device. It seems that the POST parameters passed in this request to set up routes on the device can be set in such a way that would result in passing commands to a "system" API in the function and thus result in command injection on the device. If the firmware version AL-R096 is dissected using binwalk tool, we obtain a cpio-root archive which contains the filesystem set up on the device that contains all the binaries. The binary "goahead" is the one that has the vulnerable function that recieves the values sent by the POST request. If we open this binary in IDA-pro we will notice that this follows a MIPS little endian format. The function sub_43C280in IDA pro is identified to be receiving the values sent in the POST request and the value set in POST parameter "ip_address" is extracted at address 0x0043C2F0. The POST parameter "ipaddress" is concatenated at address 0x0043C958 and this is passed to a "system" function at address 0x00437284. This allows an attacker to provide the payload of his/her choice and finally take control of the device.

An issue was discovered on Securifi Almond, Almond+, and Almond 2015 devices with firmware AL-R096. The device provides a user with the capability of adding new routes to the device. It seems that the POST parameters passed in this request to set up routes on the device can be set in such a way that would result in passing commands to a "popen" API in the function and thus result in command injection on the device. If the firmware version AL-R096 is dissected using binwalk tool, we obtain a cpio-root archive which contains the filesystem set up on the device that contains all the binaries. The binary "goahead" is the one that has the vulnerable function that receives the values sent by the POST request. If we open this binary in IDA-pro we will notice that this follows a MIPS little endian format. The function sub_00420F38 in IDA pro is identified to be receiving the values sent in the POST request and the value set in POST parameter "dest" is extracted at address 0x00420FC4. The POST parameter "dest is concatenated in a route add command and this is passed to a "popen" function at address 0x00421220. This allows an attacker to provide the payload of his/her choice and finally take control of the device.

An issue was discovered on Securifi Almond, Almond+, and Almond 2015 devices with firmware AL-R096. The device provides a user with the capability of blocking key words passing in the web traffic to prevent kids from watching content that might be deemed unsafe using the web management interface. It seems that the device does not implement any cross-site scripting protection mechanism which allows an attacker to trick a user who is logged in to the web management interface into executing a stored cross-site scripting payload on the user's browser and execute any action on the device provided by the web management interface.

An issue was discovered on Securifi Almond, Almond+, and Almond 2015 devices with firmware AL-R096. The device provides a user with the capability of setting a name for the wireless network. These values are stored by the device in NVRAM (Non-volatile RAM). It seems that the POST parameters passed in this request to set up names on the device do not have a string length check on them. This allows an attacker to send a large payload in the "mssid_1" POST parameter. The device also allows a user to view the name of the Wifi Network set by the user. While processing this request, the device calls a function at address 0x00412CE4 (routerSummary) in the binary "webServer" located in Almond folder, which retrieves the value set earlier by "mssid_1" parameter as SSID2 and this value then results in overflowing the stack set up for this function and allows an attacker to control $ra register value on the stack which allows an attacker to control the device by executing a payload of an attacker's choice. If the firmware version AL-R096 is dissected using binwalk tool, we obtain a cpio-root archive which contains the filesystem set up on the device that contains all the binaries. The binary "goahead" is the one that has the vulnerable function that receives the values sent by the POST request. If we open this binary in IDA-pro we will notice that this follows a MIPS little endian format. The function sub_00420F38 in IDA pro is identified to be receiving the values sent in the POST parameter "mssid_1" at address 0x0042BA00 and then sets in the NVRAM at address 0x0042C314. The value is later retrieved in the function at address 0x00412EAC and this results in overflowing the buffer as the function copies the value directly on the stack.

An issue was discovered on Securifi Almond, Almond+, and Almond 2015 devices with firmware AL-R096. The device provides a user with the capability of setting name for wireless network. These values are stored by the device in NVRAM (Non-volatile RAM). It seems that the POST parameters passed in this request to set up names on the device do not have a string length check on them. This allows an attacker to send a large payload in the "mssid_1" POST parameter. The device also allows a user to view the name of the Wifi Network set by the user. While processing this request, the device calls a function named "getCfgToHTML" at address 0x004268A8 which retrieves the value set earlier by "mssid_1" parameter as SSID2 and this value then results in overflowing the stack set up for this function and allows an attacker to control $ra register value on the stack which allows an attacker to control the device by executing a payload of an attacker's choice. If the firmware version AL-R096 is dissected using binwalk tool, we obtain a cpio-root archive which contains the filesystem set up on the device that contains all the binaries. The binary "goahead" is the one that has the vulnerable function that recieves the values sent by the POST request. If we open this binary in IDA-pro we will notice that this follows a MIPS little endian format. The function sub_00420F38 in IDA pro is identified to be receiving the values sent in the POST parameter "mssid_1" at address 0x0042BA00 and then sets in the NVRAM at address 0x0042C314. The value is later retrieved in the function "getCfgToHTML" at address 0x00426924 and this results in overflowing the buffer due to "strcat" function that is utilized by this function.

An issue was discovered on Vera VeraEdge 1.7.19 and Veralite 1.7.481 devices. The device provides UPnP services that are available on port 3480 and can also be accessed via port 80 using the url "/port_3480". It seems that the UPnP services provide "request_image" as one of the service actions for a normal user to retrieve an image from a camera that is controlled by the controller. It seems that the "res" (resolution) parameter passed in the query string is not sanitized and is stored on the stack which allows an attacker to overflow the buffer. The function "LU::Generic_IP_Camera_Manager::REQ_Image" is activated when the lu_request_image is passed as the "id" parameter in the query string. This function then calls "LU::Generic_IP_Camera_Manager::GetUrlFromArguments". This function retrieves all the parameters passed in the query string including "res" and then uses the value passed in it to fill up buffer using the sprintf function. However, the function in this case lacks a simple length check and as a result an attacker who is able to send more than 184 characters can easily overflow the values stored on the stack including the $RA value and thus execute code on the device.

An issue was discovered on Vera VeraEdge 1.7.19 and Veralite 1.7.481 devices. The device provides UPnP services that are available on port 3480 and can also be accessed via port 80 using the url "/port_3480". It seems that the UPnP services provide "request_image" as one of the service actions for a normal user to retrieve an image from a camera that is controlled by the controller. It seems that the "URL" parameter passed in the query string is not sanitized and is stored on the stack which allows an attacker to overflow the buffer. The function "LU::Generic_IP_Camera_Manager::REQ_Image" is activated when the lu_request_image is passed as the "id" parameter in query string. This function then calls "LU::Generic_IP_Camera_Manager::GetUrlFromArguments" and passes a "pointer" to the function where it will be allowed to store the value from the URL parameter. This pointer is passed as the second parameter $a2 to the function "LU::Generic_IP_Camera_Manager::GetUrlFromArguments". However, neither the callee or the caller in this case performs a simple length check and as a result an attacker who is able to send more than 1336 characters can easily overflow the values stored on the stack including the $RA value and thus execute code on the device.

Remote code execution can occur in Asterisk Open Source 13.x before 13.14.1 and 14.x before 14.3.1 and Certified Asterisk 13.13 before 13.13-cert3 because of a buffer overflow in a CDR user field, related to X-ClientCode in chan_sip, the CDR dialplan function, and the AMI Monitor action.

spice versions though 0.13 are vulnerable to out-of-bounds memory access when processing specially crafted messages from authenticated attacker to the spice server resulting into crash and/or server memory leak.

Buffer overflow in SYS.DBMS_DRS in Oracle Database 9.2.0.7 and 10.1.0.4 allows remote authenticated users to cause a denial of service (crash) or execute arbitrary code via the GET_PROPERTY function in SYS.DBMS_DRS, aka DB03.

Multiple buffer overflows in the ctl_put* functions in NTP before 4.2.8p10 and 4.3.x before 4.3.94 allow remote authenticated users to have unspecified impact via a long variable.

The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities.

The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities.

A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device.  The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability.

The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities.

A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device.  The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability.

Apache PLC4X - PLC4C (Only the C language implementation was effected) was vulnerable to an unsigned integer underflow flaw inside the tcp transport. Users should update to 0.9.1, which addresses this issue. However, in order to exploit this vulnerability, a user would have to actively connect to a mallicious device which could send a response with invalid content. Currently we consider the probability of this being exploited as quite minimal, however this could change in the future, especially with the industrial networks growing more and more together.

A vulnerability in Common Internet Filesystem (CIFS) code in the Clientless SSL VPN functionality of Cisco ASA Software, Major Releases 9.0-9.6, could allow an authenticated, remote attacker to cause a heap overflow. The vulnerability is due to insufficient validation of user supplied input. An attacker could exploit this vulnerability by sending a crafted URL to the affected system. An exploit could allow the remote attacker to cause a reload of the affected system or potentially execute code. Note: Only traffic directed to the affected system can be used to exploit this vulnerability. This vulnerability affects systems configured in routed firewall mode only and in single or multiple context mode. This vulnerability can be triggered by IPv4 or IPv6 traffic. A valid TCP connection is needed to perform the attack. The attacker needs to have valid credentials to log in to the Clientless SSL VPN portal. Vulnerable Cisco ASA Software running on the following products may be affected by this vulnerability: Cisco ASA 5500 Series Adaptive Security Appliances, Cisco ASA 5500-X Series Next-Generation Firewalls, Cisco Adaptive Security Virtual Appliance (ASAv), Cisco ASA for Firepower 9300 Series, Cisco ASA for Firepower 4100 Series. Cisco Bug IDs: CSCvc23838.

A stack buffer overflow flaw was found in the Quick Emulator (QEMU) before 2.9 built with the Network Block Device (NBD) client support. The flaw could occur while processing server's response to a 'NBD_OPT_LIST' request. A malicious NBD server could use this issue to crash a remote NBD client resulting in DoS or potentially execute arbitrary code on client host with privileges of the QEMU process.

HP Color LaserJet Pro M280-M281 Multifunction Printer series (before v. 20190419), HP LaserJet Pro MFP M28-M31 Printer series (before v. 20190426) may have embedded web server attributes which may be potentially vulnerable to Buffer Overflow.

A buffer overflow vulnerability in "Add command" functionality exists in Flexense SyncBreeze Enterprise <= 10.3.14. The vulnerability can be triggered by an authenticated attacker who submits more than 5000 characters as the command name. It will cause termination of the SyncBreeze Enterprise server and possibly remote command execution with SYSTEM privilege.

Vyper is a Pythonic Smart Contract Language for the EVM. In affected versions when performing a function call inside a literal struct, there is a memory corruption issue that occurs because of an incorrect pointer to the the top of the stack. This issue has been resolved in version 0.3.0.

A Buffer Overflow issue was discovered in Asterisk Open Source 13 before 13.18.1, 14 before 14.7.1, and 15 before 15.1.1 and Certified Asterisk 13.13 before 13.13-cert7. No size checking is done when setting the user field for Party B on a CDR. Thus, it is possible for someone to use an arbitrarily large string and write past the end of the user field storage buffer. NOTE: this is different from CVE-2017-7617, which was only about the Party A buffer.

Buffer overflow in certain client utilities in OpenAFS before 1.6.2 allows remote authenticated users to cause a denial of service (crash) and possibly execute arbitrary code via a long fileserver ACL entry.

Stack-based buffer overflow in the receive_tcppacket function in net_packet.c in tinc before 1.0.21 and 1.1 before 1.1pre7 allows remote authenticated peers to cause a denial of service (crash) or possibly execute arbitrary code via a large TCP packet.

Stack-based buffer overflow in the acl_get function in Oracle MySQL 5.5.19 and other versions through 5.5.28, and 5.1.53 and other versions through 5.1.66, and MariaDB 5.5.2.x before 5.5.28a, 5.3.x before 5.3.11, 5.2.x before 5.2.13 and 5.1.x before 5.1.66, allows remote authenticated users to execute arbitrary code via a long argument to the GRANT FILE command.

Heap-based buffer overflow in the substr function in parsing.c in cgit 0.9.0.3 and earlier allows remote authenticated users to cause a denial of service (crash) and possibly execute arbitrary code via an empty username in the "Author" field in a commit.

On Insteon Hub 2245-222 devices with firmware version 1012, specially crafted replies received from the PubNub service can cause buffer overflows on a global section overwriting arbitrary data. An attacker should impersonate PubNub and answer an HTTPS GET request to trigger this vulnerability. A strcpy overflows the buffer insteon_pubnub.channel_ad_r, which has a size of 16 bytes. An attacker can send an arbitrarily long "ad_r" parameter in order to exploit this vulnerability.

Double free vulnerability in tif_jpeg.c in libtiff before 3.8.1 allows context-dependent attackers to cause a denial of service (crash) and possibly execute arbitrary code via a crafted TIFF image that triggers errors related to "setfield/getfield methods in cleanup functions."

Dameng DM Database Server allows remote authenticated users to cause a denial of service (crash) and possibly execute arbitrary code via unspecified vectors related to the SP_DEL_BAK_EXPIRED procedure in wdm_dll.dll, which triggers memory corruption.

Heap-based buffer overflow in IBM DB2 9.1 before FP9, 9.5 before FP6, and 9.7 before FP2 allows remote authenticated users to have an unspecified impact via a SELECT statement that has a long column name generated with the REPEAT function.

Buffer overflow in Bip 0.8.8 and earlier might allow remote authenticated users to execute arbitrary code via vectors involving a series of TCP connections that triggers use of many open file descriptors.

In Android for MSM, Firefox OS for MSM, QRD Android, with all Android releases from CAF using the Linux kernel, by calling an IPA ioctl and searching for routing/filer/hdr rule handle from ipa_idr pointer using ipa_idr_find() function, the wrong structure pointer can be returned resulting in a slab out of bound access in the IPA driver.

Multiple buffer overflows in gram.y for PostgreSQL 8.0.1 and earlier may allow attackers to execute arbitrary code via (1) a large number of variables in a SQL statement being handled by the read_sql_construct function, (2) a large number of INTO variables in a SELECT statement being handled by the make_select_stmt function, (3) a large number of arbitrary variables in a SELECT statement being handled by the make_select_stmt function, and (4) a large number of INTO variables in a FETCH statement being handled by the make_fetch_stmt function, a different set of vulnerabilities than CVE-2005-0245.

On Insteon Hub 2245-222 devices with firmware version 1012, specially crafted replies received from the PubNub service can cause buffer overflows on a global section overwriting arbitrary data. An attacker should impersonate PubNub and answer an HTTPS GET request to trigger this vulnerability. A strcpy overflows the buffer insteon_pubnub.channel_ak, which has a size of 16 bytes. An attacker can send an arbitrarily long "ak" parameter in order to exploit this vulnerability.

Buffer overflow in the ParseCommand function in hpgl-input.c in the hpgltops program for CUPS 1.1.22 allows remote attackers to execute arbitrary code via a crafted HPGL file.

An exploitable buffer overflow vulnerability exists in the PubNub message handler for the "control" channel of Insteon Hub running firmware version 1012. Specially crafted replies received from the PubNub service can cause buffer overflows on a global section overwriting arbitrary data. A strcpy overflows the buffer insteon_pubnub.channel_cc_r, which has a size of 16 bytes. An attacker can send an arbitrarily long "c_r" parameter in order to exploit this vulnerability. An attacker should impersonate PubNub and answer an HTTPS GET request to trigger this vulnerability.

Multiple stack-based buffer overflows in TP-Link WR940N WiFi routers with hardware version 4 allow remote authenticated users to execute arbitrary code via the (1) ping_addr parameter to PingIframeRpm.htm or (2) dnsserver2 parameter to WanStaticIpV6CfgRpm.htm.

Heap-based buffer overflow in IBM WebSphere MQ 6.0 before 6.0.2.11 and 7.0 before 7.0.1.5 allows remote authenticated users to execute arbitrary code or cause a denial of service (queue manager crash) by inserting an invalid message into the queue.

Multiple stack-based buffer overflows in the IMAP server component in GroupWise Internet Agent (GWIA) in Novell GroupWise before 8.02HP allow remote attackers to execute arbitrary code via a long (1) LIST or (2) LSUB command.

Buffer overflows in (1) circle_poly, (2) path_encode and (3) path_add (also incorrectly identified as path_addr) for PostgreSQL 7.2.3 and earlier allow attackers to cause a denial of service and possibly execute arbitrary code, possibly as a result of an integer overflow.

Stack-based buffer overflow in the bgp_route_refresh_receive function in bgp_packet.c in bgpd in Quagga before 0.99.17 allows remote authenticated users to cause a denial of service (daemon crash) or possibly execute arbitrary code via a malformed Outbound Route Filtering (ORF) record in a BGP ROUTE-REFRESH (RR) message.

Buffer overflow in programs/pluto/xauth.c in the client in Openswan 2.6.25 through 2.6.28 might allow remote authenticated gateways to execute arbitrary code or cause a denial of service via long (1) cisco_dns_info or (2) cisco_domain_info data in a packet.

Geo++ GNCASTER 1.4.0.7 and earlier allows remote authenticated users to cause a denial of service (application crash) and possibly execute arbitrary code via a long NMEA data sentence.

Stack-based buffer overflow in NWFTPD.nlm before 5.10.01 in the FTP server in Novell NetWare 5.1 through 6.5 SP8 allows remote authenticated users to cause a denial of service (daemon crash) or possibly execute arbitrary code via a long (1) MKD, (2) RMD, (3) RNFR, or (4) DELE command.

IBM Domino 8.5.3, and 9.0 is vulnerable to a stack based overflow in the IMAP service that could allow an authenticated attacker to execute arbitrary code by specifying a large mailbox name. IBM X-Force ID: 124749.

Heap-based buffer overflow in the SMB implementation in NetApp Clustered Data ONTAP before 8.3.2P8 and 9.0 before P2 allows remote authenticated users to cause a denial of service or execute arbitrary code.

Stack-based buffer overflow in the IMAP server in Alt-N Technologies MDaemon 9.6.4 allows remote authenticated users to execute arbitrary code via a FETCH command with a long BODY.

A vulnerability was found in Tenda AC8 16.03.34.09 and classified as critical. Affected by this issue is the function route_static_check of the file /goform/SetStaticRouteCfg. The manipulation of the argument list leads to stack-based buffer overflow. The attack may be launched remotely. The exploit has been disclosed to the public and may be used.

A vulnerability was found in D-Link DIR-605L 2.13B01. It has been declared as critical. This vulnerability affects the function formSetPortTr of the file /goform/formSetPortTr. The manipulation of the argument curTime leads to buffer overflow. The attack can be initiated remotely. The exploit has been disclosed to the public and may be used.