A vulnerability in the pfe-chassisd Chassis Manager (CMLC) daemon of Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) to the EX4300 when specific valid broadcast packets create a broadcast storm condition when received on the me0 interface of the EX4300 Series device. A reboot of the device is required to restore service. Continued receipt of these valid broadcast packets will create a sustained Denial of Service (DoS) against the device. Affected releases are Juniper Networks Junos OS: 16.1 versions above and including 16.1R1 prior to 16.1R7-S5; 17.1 versions prior to 17.1R3; 17.2 versions prior to 17.2R3; 17.3 versions prior to 17.3R3-S2; 17.4 versions prior to 17.4R2; 18.1 versions prior to 18.1R3; 18.2 versions prior to 18.2R2.

Crafted packets destined to the management interface (fxp0) of an SRX340 or SRX345 services gateway may create a denial of service (DoS) condition due to buffer space exhaustion. This issue only affects the SRX340 and SRX345 services gateways. No other products or platforms are affected by this vulnerability. Affected releases are Juniper Networks Junos OS: 15.1X49 versions prior to 15.1X49-D160 on SRX340/SRX345; 17.3 on SRX340/SRX345; 17.4 versions prior to 17.4R2-S3, 17.4R3 on SRX340/SRX345; 18.1 versions prior to 18.1R3-S1 on SRX340/SRX345; 18.2 versions prior to 18.2R2 on SRX340/SRX345; 18.3 versions prior to 18.3R1-S2, 18.3R2 on SRX340/SRX345. This issue does not affect Junos OS releases prior to 15.1X49 on any platform.

On Juniper Networks EX4300-MP Series, EX4600 Series and QFX5K Series deployed in a Virtual Chassis configuration, receipt of a stream of specific layer 2 frames can cause high CPU load, which could lead to traffic interruption. This issue does not occur when the device is deployed in Stand Alone configuration. The offending layer 2 frame packets can originate only from within the broadcast domain where the device is connected. This issue affects Juniper Networks Junos OS on EX4300-MP Series, EX4600 Series and QFX5K Series: 17.3 versions prior to 17.3R3-S9; 17.4 versions prior to 17.4R2-S11, 17.4R3-S2, 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S5; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S3, 20.1R2.

While experiencing a broadcast storm, placing the fxp0 interface into promiscuous mode via the 'monitor traffic interface fxp0' can cause the system to crash and restart (vmcore). This issue only affects Junos OS 15.1 and later releases, and affects both single core and multi-core REs. Releases prior to Junos OS 15.1 are unaffected by this vulnerability. Affected releases are Juniper Networks Junos OS: 15.1 versions prior to 15.1F6-S11, 15.1R4-S9, 15.1R6-S6, 15.1R7; 15.1X49 versions prior to 15.1X49-D140; 15.1X53 versions prior to 15.1X53-D59 on EX2300/EX3400; 15.1X53 versions prior to 15.1X53-D67 on QFX10K; 15.1X53 versions prior to 15.1X53-D233 on QFX5200/QFX5110; 15.1X53 versions prior to 15.1X53-D471, 15.1X53-D490 on NFX; 16.1 versions prior to 16.1R3-S8, 16.1R5-S4, 16.1R6-S1, 16.1R7; 16.2 versions prior to 16.2R1-S6, 16.2R2-S5, 16.2R3; 17.1 versions prior to 17.1R1-S7, 17.1R2-S7, 17.1R3; 17.2 versions prior to 17.2R1-S6, 17.2R2-S4, 17.2R3; 17.2X75 versions prior to 17.2X75-D90, 17.2X75-D110; 17.3 versions prior to 17.3R1-S4, 17.3R2; 17.4 versions prior to 17.4R1-S3, 17.4R2.

On QFX5000 Series and EX4600 switches, a high rate of Ethernet pause frames or an ARP packet storm received on the management interface (fxp0) can cause egress interface congestion, resulting in routing protocol packet drops, such as BGP, leading to peering flaps. The following log message may also be displayed: fpc0 dcbcm_check_stuck_buffers: Buffers are stuck on queue 7 of port 45 This issue only affects the QFX5000 Series products (QFX5100, QFX5110, QFX5200, QFX5210) and the EX4600 switch. No other platforms are affected by this issue. Affected releases are Juniper Networks Junos OS: 14.1X53 versions prior to 14.1X53-D47 on QFX5000 Series and EX4600; 15.1 versions prior to 15.1R7, 15.1R8 on QFX5000 Series and EX4600; 15.1X53 versions prior to 15.1X53-D233 on QFX5000 Series and EX4600; 16.1 versions prior to 16.1R7 on QFX5000 Series and EX4600; 16.2 versions prior to 16.2R3 on QFX5000 Series and EX4600; 17.1 versions prior to 17.1R2-S9, 17.1R3 on QFX5000 Series and EX4600; 17.2 versions prior to 17.2R2-S6, 17.2R3 on QFX5000 Series and EX4600; 17.2X75 versions prior to 17.2X75-D42 on QFX5000 Series and EX4600; 17.3 versions prior to 17.3R3 on QFX5000 Series and EX4600; 17.4 versions prior to 17.4R2 on QFX5000 Series and EX4600; 18.1 versions prior to 18.1R2 on QFX5000 Series and EX4600.

On Juniper Networks Junos EX series, QFX Series, MX Series and SRX branch series devices, a memory leak occurs every time the 802.1X authenticator port interface flaps which can lead to other processes, such as the pfex process, responsible for packet forwarding, to crash and restart. An administrator can use the following CLI command to monitor the status of memory consumption: user@device> show task memory detail Please refer to https://kb.juniper.net/KB31522 for details. This issue affects Juniper Networks Junos OS: 14.1X53 versions prior to 14.1X53-D54; 15.1X49 versions prior to 15.1X49-D240 ; 15.1X53 versions prior to 15.1X53-D593; 16.1 versions prior to 16.1R7-S8; 17.2 versions prior to 17.2R3-S4; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S11, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10 ; 18.2 versions prior to 18.2R2-S7, 18.2R3-S3; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3-S2; 19.1 versions prior to 19.1R1-S5, 19.1R2-S2, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2. This issue does not affect Juniper Networks Junos OS 12.3, 15.1.

On Juniper Networks MX Series and EX9200 Series platforms with Trio-based MPCs (Modular Port Concentrators) where Integrated Routing and Bridging (IRB) interfaces are configured and mapped to a VPLS instance or a Bridge-Domain, certain Layer 2 network events at Customer Edge (CE) devices may cause memory leaks in the MPC of Provider Edge (PE) devices which can cause an out of memory condition and MPC restart. When this issue occurs, there will be temporary traffic interruption until the MPC is restored. An administrator can use the following CLI command to monitor the status of memory usage level of the MPC: user@device> show system resource-monitor fpc FPC Resource Usage Summary Free Heap Mem Watermark : 20 % Free NH Mem Watermark : 20 % Free Filter Mem Watermark : 20 % * - Watermark reached Slot # % Heap Free RTT Average RTT 1 87 PFE # % ENCAP mem Free % NH mem Free % FW mem Free 0 NA 88 99 1 NA 89 99 When the issue is occurring, the value of “% NH mem Free” will go down until the MPC restarts. This issue affects MX Series and EX9200 Series with Trio-based PFEs (Packet Forwarding Engines), including MX-MPC1-3D, MX-MPC1E-3D, MX-MPC2-3D, MX-MPC2E-3D, MPC-3D-16XGE, and CHAS-MXxx Series MPCs. No other products or platforms are affected by this issue. This issue affects Juniper Networks Junos OS on MX Series, EX9200 Series: 17.3 versions prior to 17.3R3-S10; 17.4 versions prior to 17.4R3-S3; 18.2 versions prior to 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R3-S6; 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R2-S2, 19.4R3; 20.2 versions prior to 20.2R1-S3, 20.2R2; 20.3 versions prior to 20.3R1-S1,, 20.3R2. This issue does not affect Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R3-S2; 18.1; 18.2 versions prior to 18.2R3-S4; 18.3 versions prior to 18.3R3-S2; 18.4 versions prior to 18.4R3-S1; 19.1; 19.2 versions prior to 19.2R2; 19.3 versions prior to 19.3R3; 19.4 versions prior to 19.4R2.

An Uncontrolled Resource Consumption vulnerability in the ARP daemon (arpd) and Network Discovery Protocol (ndp) process of Juniper Networks Junos OS Evolved allows a malicious attacker on the local network to consume memory resources, ultimately resulting in a Denial of Service (DoS) condition. Link-layer functions such as IPv4 and/or IPv6 address resolution may be impacted, leading to traffic loss. The processes do not recover on their own and must be manually restarted. Changes in memory usage can be monitored using the following shell commands (header shown for clarity): user@router:/var/log# ps aux | grep arpd USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 31418 59.0 0.7 *5702564* 247952 ? xxx /usr/sbin/arpd --app-name arpd -I object_select --shared-objects-mode 3 user@router:/var/log# ps aux | grep arpd USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 31418 49.1 1.0 *5813156* 351184 ? xxx /usr/sbin/arpd --app-name arpd -I object_select --shared-objects-mode 3 Memory usage can be monitored for the ndp process in a similar fashion: user@router:/var/log# ps aux | grep ndp USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 14935 0.0 0.1 *5614052* 27256 ? Ssl Jun15 0:17 /usr/sbin/ndp -I no_tab_chk,object_select --app-name ndp --shared-obje user@router:/var/log# ps aux | grep ndp USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 14935 0.0 0.1 *5725164* 27256 ? Ssl Jun15 0:17 /usr/sbin/ndp -I no_tab_chk,object_select --app-name ndp --shared-obje This issue affects Juniper Networks Junos OS Evolved: 19.4 versions prior to 19.4R2-S3-EVO; 20.1 versions prior to 20.1R2-S4-EVO; all versions of 20.2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 19.4R2-EVO.

An Uncontrolled Resource Consumption vulnerability in the handling of IPv6 neighbor state change events in Juniper Networks Junos OS allows an adjacent attacker to cause a memory leak in the Flexible PIC Concentrator (FPC) of an ACX5448 router. The continuous flapping of an IPv6 neighbor with specific timing will cause the FPC to run out of resources, leading to a Denial of Service (DoS) condition. Once the condition occurs, further packet processing will be impacted, creating a sustained Denial of Service (DoS) condition, requiring a manual PFE restart to restore service. The following error messages will be seen after the FPC resources have been exhausted: fpc0 DNX_NH::dnx_nh_tag_ipv4_hw_install(),3135: dnx_nh_tag_ipv4_hw_install: BCM L3 Egress create object failed for NH 602 (-14:No resources for operation), BCM NH Params: unit:0 Port:41, L3_INTF:0 Flags: 0x40 fpc0 DNX_NH::dnx_nh_tag_ipv4_hw_install(),3135: dnx_nh_tag_ipv4_hw_install: BCM L3 Egress create object failed for NH 602 (-14:No resources for operation), BCM NH Params: unit:0 Port:41, L3_INTF:0 Flags: 0x40 fpc0 DNX_NH::dnx_nh_tag_ipv4_hw_install(),3135: dnx_nh_tag_ipv4_hw_install: BCM L3 Egress create object failed for NH 602 (-14:No resources for operation), BCM NH Params: unit:0 Port:41, L3_INTF:0 Flags: 0x40 fpc0 DNX_NH::dnx_nh_tag_ipv4_hw_install(),3135: dnx_nh_tag_ipv4_hw_install: BCM L3 Egress create object failed for NH 602 (-14:No resources for operation), BCM NH Params: unit:0 Port:41, L3_INTF:0 Flags: 0x40 This issue only affects the ACX5448 router. No other products or platforms are affected by this vulnerability. This issue affects Juniper Networks Junos OS on ACX5448: 18.4 versions prior to 18.4R3-S10; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R1-S8, 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S3, 19.4R2-S2, 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R1-S1, 20.2R2.

On Juniper Networks EX4300-MP Series, EX4600 Series and QFX5K Series deployed in (Ethernet VPN) EVPN-(Virtual Extensible LAN) VXLAN configuration, receipt of a stream of specific VXLAN encapsulated layer 2 frames can cause high CPU load, which could lead to network protocol operation issue and traffic interruption. This issue affects devices that are configured as a Layer 2 or Layer 3 gateway of an EVPN-VXLAN deployment. The offending layer 2 frames that cause the issue originate from a different access switch that get encapsulated within the same EVPN-VXLAN domain. This issue affects Juniper Networks Junos OS on EX4300-MP Series, EX4600 Series and QFX5K Series: 17.3 versions prior to 17.3R3-S9; 17.4 versions prior to 17.4R2-S11, 17.4R3-S2, 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S5; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R2-S2, 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R2-S1, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S3, 20.1R2.

On Juniper Networks EX2300 Series, receipt of a stream of specific multicast packets by the layer2 interface can cause high CPU load, which could lead to traffic interruption. This issue occurs when multicast packets are received by the layer 2 interface. To check if the device has high CPU load due to this issue, the administrator can issue the following command: user@host> show chassis routing-engine Routing Engine status: ... Idle 2 percent the "Idle" value shows as low (2 % in the example above), and also the following command: user@host> show system processes summary ... PID USERNAME PRI NICE SIZE RES STATE TIME WCPU COMMAND 11639 root 52 0 283M 11296K select 12:15 44.97% eventd 11803 root 81 0 719M 239M RUN 251:12 31.98% fxpc{fxpc} the eventd and the fxpc processes might use higher WCPU percentage (respectively 44.97% and 31.98% in the above example). This issue affects Juniper Networks Junos OS on EX2300 Series: 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S5; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S2, 20.1R2.

On Juniper Networks EX4300 Series, receipt of a stream of specific IPv4 packets can cause Routing Engine (RE) high CPU load, which could lead to network protocol operation issue and traffic interruption. This specific packets can originate only from within the broadcast domain where the device is connected. This issue occurs when the packets enter to the IRB interface. Only IPv4 packets can trigger this issue. IPv6 packets cannot trigger this issue. This issue affects Juniper Networks Junos OS on EX4300 series: 17.3 versions prior to 17.3R3-S9; 17.4 versions prior to 17.4R2-S11, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R3-S4; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R2-S4, 18.4R3-S2; 19.1 versions prior to 19.1R2-S2, 19.1R3-S1; 19.2 versions prior to 19.2R1-S5, 19.2R2-S1, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2; 20.1 versions prior to 20.1R1-S3, 20.1R2.

A Denial of Service (DoS) vulnerability in the processing of a flood of specific ARP traffic in Juniper Networks Junos OS on the EX4300 switch, sent from the local broadcast domain, may allow an unauthenticated network-adjacent attacker to trigger a PFEMAN watchdog timeout, causing the Packet Forwarding Engine (PFE) to crash and restart. After the restart, transit traffic will be temporarily interrupted until the PFE is reprogrammed. In a virtual chassis (VC), the impacted Flexible PIC Concentrator (FPC) may split from the VC temporarily, and join back into the VC once the PFE restarts. Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on the EX4300: All versions prior to 15.1R7-S12; 18.4 versions prior to 18.4R2-S10, 18.4R3-S11; 19.1 versions prior to 19.1R3-S8; 19.2 versions prior to 19.2R1-S9, 19.2R3-S4; 19.3 versions prior to 19.3R3-S5; 19.4 versions prior to 19.4R2-S6, 19.4R3-S7; 20.1 versions prior to 20.1R3-S3; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S2; 20.4 versions prior to 20.4R3-S1; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R2-S1, 21.2R3; 21.3 versions prior to 21.3R1-S2, 21.3R2.

An Uncontrolled Resource Consumption vulnerability in Juniper Networks Junos OS on EX2300, EX3400 and EX4300 Series platforms allows an adjacent attacker sending a stream of layer 2 frames will trigger an Aggregated Ethernet (AE) interface to go down and thereby causing a Denial of Service (DoS). By continuously sending a stream of specific layer 2 frames an attacker will sustain the Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS EX4300 Series All versions prior to 15.1R7-S7; 16.1 versions prior to 16.1R7-S8; 17.1 versions prior to 17.1R2-S12; 17.2 versions prior to 17.2R3-S4; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S10, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R2-S7, 18.2R3-S3; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3-S1; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S2, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2. Juniper Networks Junos OS EX3400 and EX4300-MP Series All versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S9, 18.4R3-S7; 19.1 versions prior to 19.1R2-S3, 19.1R3-S4; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R2. Juniper Networks Junos OS EX2300 Series All versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.1 versions prior to 19.1R2-S3, 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S7, 19.3R3-S3; 19.4 versions prior to 19.4R3-S5; 20.1 versions prior to 20.1R2-S2, 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R2-S1, 20.4R3; 21.1 versions prior to 21.1R2.

An Uncontrolled Resource Consumption vulnerability in the Layer 2 Address Learning Daemon (l2ald) of Juniper Networks Junos OS Evolved allows an unauthenticated, adjacent attacker to cause a memory leak, eventually exhausting all system memory, leading to a system crash and Denial of Service (DoS). Certain MAC table updates cause a small amount of memory to leak.  Once memory utilization reaches its limit, the issue will result in a system crash and restart. To identify the issue, execute the CLI command: user@device> show platform application-info allocations app l2ald-agent EVL Object Allocation Statistics: Node   Application     Context Name                               Live   Allocs   Fails     Guids re0   l2ald-agent               net::juniper::rtnh::L2Rtinfo       1069096 1069302   0         1069302 re0   l2ald-agent               net::juniper::rtnh::NHOpaqueTlv     114     195       0         195 This issue affects Junos OS Evolved: * All versions before 21.4R3-S8-EVO, * from 22.2-EVO before 22.2R3-S4-EVO, * from 22.3-EVO before 22.3R3-S3-EVO, * from 22.4-EVO before 22.4R3-EVO, * from 23.2-EVO before 23.2R2-EVO.

The kernel memory usage represented as "temp" via 'show system virtual-memory' may constantly increase when Integrated Routing and Bridging (IRB) is configured with multiple underlay physical interfaces, and one interface flaps. This memory leak can affect running daemons (processes), leading to an extended Denial of Service (DoS) condition. Usage of "temp" virtual memory, shown here by a constantly increasing value of outstanding Requests, can be monitored by executing the 'show system virtual-memory' command as shown below: user@junos> show system virtual-memory |match "fpc|type|temp" fpc0: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2023 431K - 10551 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 fpc1: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2020 431K - 6460 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 user@junos> show system virtual-memory |match "fpc|type|temp" fpc0: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2023 431K - 16101 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 fpc1: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2020 431K - 6665 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 user@junos> show system virtual-memory |match "fpc|type|temp" fpc0: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2023 431K - 21867 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 fpc1: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2020 431K - 6858 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S6; 17.1 versions prior to 17.1R2-S11, 17.1R3-S1; 17.2 versions prior to 17.2R2-S8, 17.2R3-S3; 17.2X75 versions prior to 17.2X75-D44; 17.3 versions prior to 17.3R2-S5, 17.3R3-S6; 17.4 versions prior to 17.4R2-S5, 17.4R3; 18.1 versions prior to 18.1R3-S7; 18.2 versions prior to 18.2R2-S5, 18.2R3; 18.2X75 versions prior to 18.2X75-D33, 18.2X75-D411, 18.2X75-D420, 18.2X75-D60; 18.3 versions prior to 18.3R1-S5, 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R2-S2, 18.4R3; 19.1 versions prior to 19.1R1-S3, 19.1R2; 19.2 versions prior to 19.2R1-S3, 19.2R2. This issue does not affect Juniper Networks Junos OS 12.3 and 15.1.

On Juniper Networks Junos OS and Junos OS Evolved platforms with EVPN configured, receipt of specific BGP packets causes a slow memory leak. If the memory is exhausted the rpd process might crash. If the issue occurs, the memory leak could be seen by executing the "show task memory detail | match policy | match evpn" command multiple times to check if memory (Alloc Blocks value) is increasing. root@device> show task memory detail | match policy | match evpn ------------------------ Allocator Memory Report ------------------------ Name | Size | Alloc DTXP Size | Alloc Blocks | Alloc Bytes | MaxAlloc Blocks | MaxAlloc Bytes Policy EVPN Params 20 24 3330678 79936272 3330678 79936272 root@device> show task memory detail | match policy | match evpn ------------------------ Allocator Memory Report ------------------------ Name | Size | Alloc DTXP Size | Alloc Blocks | Alloc Bytes | MaxAlloc Blocks | MaxAlloc Bytes Policy EVPN Params 20 24 36620255 878886120 36620255 878886120 This issue affects: Juniper Networks Junos OS 19.4 versions prior to 19.4R2; 20.1 versions prior to 20.1R1-S4, 20.1R2; Juniper Networks Junos OS Evolved: 19.4 versions; 20.1 versions prior to 20.1R1-S4-EVO, 20.1R2-EVO; 20.2 versions prior to 20.2R1-EVO; This issue does not affect: Juniper Networks Junos OS releases prior to 19.4R1. Juniper Networks Junos OS Evolved releases prior to 19.4R1-EVO.

When an MX Series Broadband Remote Access Server (BRAS) is configured as a Broadband Network Gateway (BNG) with DHCPv6 enabled, jdhcpd might crash when receiving a specific crafted DHCP response message on a subscriber interface. The daemon automatically restarts without intervention, but continuous receipt of specific crafted DHCP messages will repeatedly crash jdhcpd, leading to an extended Denial of Service (DoS) condition. This issue only affects systems configured with DHCPv6 enabled. DHCPv4 is unaffected by this issue. This issue affects Juniper Networks Junos OS: 15.1 versions prior to 15.1R7-S5 on MX Series; 16.1 versions prior to 16.1R7-S5 on MX Series; 16.2 versions prior to 16.2R2-S10 on MX Series; 17.1 versions prior to 17.1R3-S1 on MX Series; 17.2 versions prior to 17.2R3-S2 on MX Series; 17.3 versions prior to 17.3R3-S6 on MX Series; 17.4 versions prior to 17.4R2-S5, 17.4R3 on MX Series; 18.1 versions prior to 18.1R3-S6 on MX Series; 18.2 versions prior to 18.2R2-S4, 18.2R3 on MX Series; 18.2X75 versions prior to 18.2X75-D50 on MX Series; 18.3 versions prior to 18.3R1-S5, 18.3R3 on MX Series; 18.4 versions prior to 18.4R2 on MX Series; 19.1 versions prior to 19.1R1-S2, 19.1R2 on MX Series.

The SRX flowd process, responsible for packet forwarding, may crash and restart when processing specific multicast packets. By continuously sending the specific multicast packets, an attacker can repeatedly crash the flowd process causing a sustained Denial of Service. This issue affects Juniper Networks Junos OS on SRX Series: 12.3X48 versions prior to 12.3X48-D90; 15.1X49 versions prior to 15.1X49-D180; 17.3 versions; 17.4 versions prior to 17.4R2-S5, 17.4R3; 18.1 versions prior to 18.1R3-S6; 18.2 versions prior to 18.2R2-S4, 18.2R3; 18.3 versions prior to 18.3R2-S1, 18.3R3; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R1-S1, 19.1R2.

The Junos OS kernel crashes after processing a specific incoming packet to the out of band management interface (such as fxp0, me0, em0, vme0) destined for another address. By continuously sending this type of packet, an attacker can repeatedly crash the kernel causing a sustained Denial of Service. Affected releases are Juniper Networks Junos OS: 17.2 versions prior to 17.2R1-S7, 17.2R3; 17.3 versions prior to 17.3R3-S3; 17.4 versions prior to 17.4R1-S4, 17.4R2; 17.2X75 versions prior to 17.2X75-D110; 18.1 versions prior to 18.1R2.

The routing protocol daemon (RPD) process will crash and restart when a specific invalid IPv4 PIM Join packet is received. While RPD restarts after a crash, repeated crashes can result in an extended Denial of Service (DoS) condition. This issue only affects IPv4 PIM. IPv6 PIM is unaffected by this vulnerability. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D77; 12.3X48 versions prior to 12.3X48-D77; 15.1 versions prior to 15.1F6-S10, 15.1R6-S6, 15.1R7; 15.1X49 versions prior to 15.1X49-D150; 15.1X53 versions prior to 15.1X53-D233, 15.1X53-D59; 16.1 versions prior to 16.1R3-S8, 16.1R4-S8, 16.1R7; 16.2 versions prior to 16.2R2-S6; 17.1 versions prior to 17.1R2-S6, 17.1R3; 17.2 versions prior to 17.2R2-S3, 17.2R3; 17.3 versions prior to 17.3R2-S4, 17.3R3; 17.4 versions prior to 17.4R2.

Receipt of a specific link-local IPv6 packet destined to the RE may cause the system to crash and restart (vmcore). By continuously sending a specially crafted IPv6 packet, an attacker can repeatedly crash the system causing a prolonged Denial of Service (DoS). This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R6-S2, 16.1R7; 16.2 versions prior to 16.2R2-S10; 17.1 versions prior to 17.1R3. This issue does not affect Juniper Networks Junos OS version 15.1 and prior versions.

An Improper Handling of Missing Values vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows an adjacent, unauthenticated attacker to cause a dcpfe process core and thereby a Denial of Service (DoS). Continued receipt of these specific frames will cause a sustained Denial of Service condition. This issue occurs when a specific malformed ethernet frame is received. This issue affects Juniper Networks Junos OS on QFX10000 Series, PTX1000 Series Series: All versions prior to 19.4R3-S10; 20.1 version 20.1R1 and later versions; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3-S1; 22.1 versions prior to 22.1R2-S1, 22.1R3; 22.2 versions prior to 22.2R1-S2, 22.2R2.

Juniper Junos OS before 13.3R9, 14.1R6 before 14.1R6-S1, and 14.1 before 14.1R7, when configured with VPLS routing-instances, allows remote attackers to obtain sensitive mbuf information by injecting a flood of Ethernet frames with IPv6 MAC addresses directly into a connected interface.

An Improper Check or Handling of Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, adjacent attacker to cause a Denial of Service (DoS). If an attacker sends a specific MPLS packet, which upon processing, causes an internal loop, that leads to a PFE crash and restart. Continued receipt of these packets leads to a sustained Denial of Service (DoS) condition. Circuit cross-connect (CCC) needs to be configured on the device for it to be affected by this issue. This issue only affects MX Series with MPC10, MPC11, LC9600, and MX304. This issue affects: Juniper Networks Junos OS 21.4 versions from 21.4R3 earlier than 21.4R3-S5; 22.2 versions from 22.2R2 earlier than 22.2R3-S2; 22.3 versions from 22.3R1 earlier than 22.3R2-S2; 22.3 versions from 22.3R3 earlier than 22.3R3-S1 22.4 versions from 22.4R1 earlier than 22.4R2-S2, 22.4R3; 23.2 versions earlier than 23.2R1-S1, 23.2R2.

An Improper Handling of Exceptional Conditions vulnerability in the broadband edge subscriber management daemon (bbe-smgd) of Juniper Networks Junos OS on MX Series allows an attacker directly connected to the vulnerable system who repeatedly flaps DHCP subscriber sessions to cause a slow memory leak, ultimately leading to a Denial of Service (DoS). Memory can only be recovered by manually restarting bbe-smgd. This issue only occurs if BFD liveness detection for DHCP subscribers is enabled. Systems without BFD liveness detection enabled are not vulnerable to this issue. Indication of the issue can be observed by periodically executing the 'show system processes extensive' command, which will indicate an increase in memory allocation for bbe-smgd. A small amount of memory is leaked every time a DHCP subscriber logs in, which will become visible over time, ultimately leading to memory starvation. user@junos> show system processes extensive | match bbe-smgd 13071 root 24 0 415M 201M select 0 0:41 7.28% bbe-smgd{bbe-smgd} 13071 root 20 0 415M 201M select 1 0:04 0.00% bbe-smgd{bbe-smgd} ... user@junos> show system processes extensive | match bbe-smgd 13071 root 20 0 420M 208M select 0 4:33 0.10% bbe-smgd{bbe-smgd} 13071 root 20 0 420M 208M select 0 0:12 0.00% bbe-smgd{bbe-smgd} ... This issue affects Juniper Networks Junos OS on MX Series: * All versions earlier than 20.4R3-S9; * 21.2 versions earlier than 21.2R3-S7; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R3-S4; * 22.2 versions earlier than 22.2R3-S3; * 22.3 versions earlier than 22.3R3-S2; * 22.4 versions earlier than 22.4R2-S2, 22.4R3; * 23.2 versions earlier than 23.2R1-S1, 23.2R2.

An Improper Input Validation vulnerability in Juniper Tunnel Driver (jtd) and ICMP module of Juniper Networks Junos OS Evolved allows an unauthenticated attacker within the MPLS administrative domain to send specifically crafted packets to the Routing Engine (RE) to cause a Denial of Service (DoS).  When specifically crafted transit MPLS IPv4 packets are received by the Packet Forwarding Engine (PFE), these packets are internally forwarded to the RE. Continued receipt of these packets may create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS: * All versions before 21.2R3-S8-EVO; * from 21.4-EVO before 21.4R3-S6-EVO; * from 22.2-EVO before 22.2R3-S4-EVO; * from 22.3-EVO before 22.3R3-S3-EVO; * from 22.4-EVO before 22.4R3-EVO; * from 23.2-EVO before 23.2R2-EVO. * from 23.4-EVO before 23.4R1-S1-EVO.

A Missing Release of Memory after Effective Lifetime vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on MX Series allows an adjacent, unauthenticated attacker to cause a Denial of Service (DoS). If an MX Series device receives PTP packets on an MPC3E that doesn't support PTP this causes a memory leak which will result in unpredictable behavior and ultimately in an MPC crash and restart. To monitor for this issue, please use the following FPC vty level commands: show heap shows an increase in "LAN buffer" utilization and show clksync ptp nbr-upd-info shows non-zero "Pending PFEs" counter. This issue affects Juniper Networks Junos OS on MX Series with MPC3E: * All versions earlier than 20.4R3-S3; * 21.1 versions earlier than 21.1R3-S4; * 21.2 versions earlier than 21.2R3; * 21.3 versions earlier than 21.3R2-S1, 21.3R3; * 21.4 versions earlier than 21.4R2; * 22.1 versions earlier than 22.1R2.

An Improper Neutralization of Equivalent Special Elements vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on PTX Series allows a unauthenticated, adjacent attacker to cause a Denial of Service (DoS). When MPLS packets are meant to be sent to a flexible tunnel interface (FTI) and if the FTI tunnel is down, these will hit the reject NH, due to which the packets get sent to the CPU and cause a host path wedge condition. This will cause the FPC to hang and requires a manual restart to recover. Please note that this issue specifically affects PTX1000, PTX3000, PTX5000 with FPC3, PTX10002-60C, and PTX10008/16 with LC110x. Other PTX Series devices and Line Cards (LC) are not affected. The following log message can be seen when the issue occurs: Cmerror Op Set: Host Loopback: HOST LOOPBACK WEDGE DETECTED IN PATH ID <id> (URI: /fpc/<fpc>/pfe/<pfe>/cm/<cm>/Host_Loopback/<cm>/HOST_LOOPBACK_MAKE_CMERROR_ID[<id>]) This issue affects Juniper Networks Junos OS: * All versions earlier than 20.4R3-S8; * 21.1 versions earlier than 21.1R3-S4; * 21.2 versions earlier than 21.2R3-S6; * 21.3 versions earlier than 21.3R3-S3; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R2-S2, 22.1R3; * 22.2 versions earlier than 22.2R2-S1, 22.2R3.

A Missing Release of Memory after Effective Lifetime vulnerability in the IKE daemon (iked) of Juniper Networks Junos OS on MX Series with SPC3, and SRX Series allows an administratively adjacent attacker which is able to successfully establish IPsec tunnels to cause a Denial of Service (DoS). If specific values for the IPsec parameters local-ip, remote-ip, remote ike-id, and traffic selectors are sent from the peer, a memory leak occurs during every IPsec SA rekey which is carried out with a specific message sequence. This will eventually result in an iked process crash and restart. The iked process memory consumption can be checked using the below command:   user@host> show system processes extensive | grep iked           PID USERNAME   PRI NICE   SIZE   RES   STATE   C TIME WCPU COMMAND           56903 root       31   0     4016M 2543M CPU0   0 2:10 10.50% iked This issue affects Juniper Networks Junos OS: * All versions earlier than 20.4R3-S9; * 21.2 versions earlier than 21.2R3-S7; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S4; * 22.1 versions earlier than 22.1R3-S3; * 22.2 versions earlier than 22.2R3-S2; * 22.3 versions earlier than 22.3R3; * 22.4 versions earlier than 22.4R3; * 23.2 versions earlier than 23.2R1-S2, 23.2R2.

An Exposure of Resource to Wrong Sphere vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on SRX 300 Series allows an unauthenticated, adjacent attacker to cause a Denial of Service (DoS). Specific valid link-local traffic is not blocked on ports in STP blocked state but is instead sent to the control plane of the device. This leads to excessive resource consumption and in turn severe impact on all control and management protocols of the device. This issue affects Juniper Networks Junos OS: * 21.2 version 21.2R3-S3 and later versions earlier than 21.2R3-S6; * 22.1 version 22.1R3 and later versions earlier than 22.1R3-S4; * 22.2 version 22.2R2 and later versions earlier than 22.2R3-S2; * 22.3 version 22.3R2 and later versions earlier than 22.3R3-S1; * 22.4 versions earlier than 22.4R2-S2, 22.4R3; * 23.2 versions earlier than 23.2R1-S1, 23.2R2. This issue does not affect Juniper Networks Junos OS 21.4R1 and later versions of 21.4.

An Access of Memory Location After End of Buffer vulnerability in the Layer-2 Control Protocols Daemon (l2cpd) of Juniper Networks Junos OS and Junos OS Evolved allows an adjacent, unauthenticated attacker to cause Denial of Service (DoS). On all Junos OS and Junos OS Evolved platforms, when LLDP is enabled on a specific interface, and a malformed LLDP packet is received, l2cpd crashes and restarts. The impact of the l2cpd crash is reinitialization of STP protocols (RSTP, MSTP or VSTP), and MVRP and ERP. Also, if any services depend on LLDP state (like PoE or VoIP device recognition), then these will also be affected. This issue affects: Junos OS: * from 21.4 before 21.4R3-S4,  * from 22.1 before 22.1R3-S4,  * from 22.2 before 22.2R3-S2,  * from 22.3 before 22.3R2-S2, 22.3R3-S1,  * from 22.4 before 22.4R3,  * from 23.2 before 23.2R2. Junos OS Evolved: * from 21.4-EVO before 21.4R3-S5-EVO,  * from 22.1-EVO before 22.1R3-S4-EVO,  * from 22.2-EVO before 22.2R3-S2-EVO,  * from 22.3-EVO before 22.3R2-S2-EVO, 22.3R3-S1-EVO,  * from 22.4-EVO before 22.4R3-EVO,  * from 23.2-EVO before 23.2R2-EVO. This issue does not affect: * Junos OS versions prior to 21.4R1; * Junos OS Evolved versions prior to 21.4R1-EVO.

An Incomplete Cleanup vulnerability in Nonstop active routing (NSR) component of Juniper Networks Junos OS allows an adjacent, unauthenticated attacker to cause memory leak leading to Denial of Service (DoS). On all Junos OS platforms, when NSR is enabled, a BGP flap will cause memory leak. A manual reboot of the system will restore the services. Note: NSR is not supported on the SRX Series and is therefore not affected by this vulnerability. The memory usage can be monitored using the below commands. user@host> show chassis routing-engine no-forwarding user@host> show system memory | no-more This issue affects: Juniper Networks Junos OS * 21.2 versions earlier than 21.2R3-S5; * 21.3 versions earlier than 21.3R3-S4; * 21.4 versions earlier than 21.4R3-S4; * 22.1 versions earlier than 22.1R3-S2; * 22.2 versions earlier than 22.2R3-S2; * 22.3 versions earlier than 22.3R2-S1, 22.3R3; * 22.4 versions earlier than 22.4R1-S2, 22.4R2. This issue does not affect Junos OS versions earlier than 20.4R3-S7.

A Missing Release of Memory after Effective Lifetime vulnerability in Routing Protocol Daemon (RPD) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, adjacent attacker to cause an rpd crash, leading to Denial of Service (DoS). On all Junos OS and Junos OS Evolved platforms, when traffic engineering is enabled for OSPF or ISIS, and a link flaps, a patroot memory leak is observed. This memory leak, over time, will lead to an rpd crash and restart. The memory usage can be monitored using the below command. user@host> show task memory detail | match patroot This issue affects: Juniper Networks Junos OS * All versions earlier than 21.2R3-S3; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S3; * 22.1 versions earlier than 22.1R3; * 22.2 versions earlier than 22.2R3. Juniper Networks Junos OS Evolved * All versions earlier than 21.3R3-S5-EVO; * 21.4 versions earlier than 21.4R3-EVO; * 22.1 versions earlier than 22.1R3-EVO; * 22.2 versions earlier than 22.2R3-EVO.

An Improper Handling of Length Parameter Inconsistency vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a logically adjacent BGP peer sending a specifically malformed BGP packet to cause rpd to crash and restart, resulting in a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. Only systems configured for Ethernet Virtual Private Networking (EVPN) signaling are vulnerable to this issue.  This issue affects iBGP and eBGP, and both IPv4 and IPv6 are affected by this vulnerability.This issue affects: Junos OS:  * all versions before 21.4R3-S11,  * from 22.2 before 22.2R3-S7,  * from 22.4 before 22.4R3-S7,  * from 23.2 before 23.2R2-S4,  * from 23.4 before 23.4R2-S5,  * from 24.2 before 24.2R2-S1,  * from 24.4 before 24.4R1-S3, 24.4R2;  Junos OS Evolved:  * all versions before 22.2R3-S7-EVO,  * from 22.4-EVO before 22.4R3-S7-EVO,  * from 23.2-EVO before 23.2R2-S4-EVO,  * from 23.4-EVO before 23.4R2-S5-EVO,  * from 24.2-EVO before 24.2R2-S1-EVO,  * from 24.4-EVO before 24.4R1-S3-EVO, 24.4R2-EVO.

An Incorrect Calculation of Buffer Size vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an adjacent unauthenticated attacker to cause a memory corruption that leads to a rpd crash.  When the logical interface using a routing instance flaps continuously, specific updates are sent to the jflow/sflow modules. This results in memory corruption, leading to an rpd crash and restart.  Continued receipt of these specific updates will cause a sustained Denial of Service condition. This issue affects Junos OS: * All versions before 21.2R3-S9, * All versions of 21.4, * All versions of 22.2, * from 22.4 before 22.4R3-S7, * from 23.2 before 23.2R2-S3, * from 23.4 before 23.4R2-S4, * from 24.2 before 24.2R2. Junos OS Evolved:  * All versions of 21.2-EVO,  * All versions of 21.4-EVO,  * All versions of 22.2-EVO,  * from 22.4 before 22.4R3-S7-EVO,  * from 23.2 before 23.2R2-S3-EVO,  * from 23.4 before 23.4R2-S4-EVO,  * from 24.2 before 24.2R2-EVO.

An Out-of-bounds Write vulnerability in the connectivity fault management (CFM) daemon of Juniper Networks Junos OS on MX Series with MPC-BUILTIN, MPC1 through MPC9 line cards allows an unauthenticated adjacent attacker to send a malformed packet to the device, leading to an FPC crash and restart, resulting in a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks: Junos OS: * All versions before 22.2R3-S1, * from 22.4 before 22.4R2. This feature is not enabled by default.

An Expected Behavior Violation vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated adjacent attacker sending a valid BGP UPDATE packet to cause a BGP session reset, resulting in a Denial of Service (DoS).  Continuous receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue affects iBGP and eBGP and both IPv4 and IPv6 are affected by this vulnerability. This issue affects Junos OS: * All versions before 21.2R3-S9, * from 21.4 before 21.4R3-S11, * from 22.2 before 22.2R3-S7, * from 22.4 before 22.4R3-S7, * from 23.2 before 23.2R2-S4, * from 23.4 before 23.4R2-S4, * from 24.2 before 24.2R2, * from 24.4 before 24.4R1-S3, 24.4R2 Junos OS Evolved: * All versions before 22.2R3-S7-EVO, * from 22.4-EVO before 22.4R3-S7-EVO, * from 23.2-EVO before 23.2R2-S4-EVO, * from 23.4-EVO before 23.4R2-S4-EVO, * from 24.2-EVO before 24.2R2-EVO, * from 24.4-EVO before 24.4R1-S3-EVO, 24.4R2-EVO.

An Improper Handling of Exceptional Conditions vulnerability in route processing of Juniper Networks Junos OS on specific end-of-life (EOL) ACX Series platforms allows an attacker to crash the Forwarding Engine Board (FEB) by flapping an interface, leading to a Denial of Service (DoS). On ACX1000, ACX1100, ACX2000, ACX2100, ACX2200, ACX4000, ACX5048, and ACX5096 devices, FEB0 will crash when the primary path port of the L2 circuit IGP (Interior Gateway Protocol) on the local device goes down. This issue is seen only when 'hot-standby' mode is configured for the L2 circuit. This issue affects Junos OS on ACX1000, ACX1100, ACX2000, ACX2100, ACX2200, ACX4000, ACX5048, and ACX5096:  * all versions before 21.2R3-S9.

A Reachable Assertion vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). When the device receives a specific BGP UPDATE packet, the rpd crashes and restarts. Continuous receipt of this specific packet will cause a sustained DoS condition. For the issue to occur, BGP multipath with "pause-computation-during-churn" must be configured on the device, and the attacker must send the paths via a BGP UPDATE from a established BGP peer. This issue affects: Junos OS: * All versions before 21.4R3-S7, * from 22.3 before 22.3R3-S3, * from 22.4 before 22.4R3-S5, * from 23.2 before 23.2R2, * from 23.4 before 23.4R2. Junos OS Evolved: * All versions before 21.4R3-S7-EVO, * from 22.3 before 22.3R3-S3-EVO, * from 22.4 before 22.4R3-S5-EVO, * from 23.2 before 23.2R2-EVO, * from 23.4 before 23.4R2-EVO.

An Incomplete List of Disallowed Inputs vulnerability in Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on QFX5000 Series and EX4600 Series allows an adjacent unauthenticated attacker which sends a high rate of specific multicast traffic to cause control traffic received from the network to be dropped. This will impact control protocols (including but not limited to routing-protocols) and lead to a Denial of Service (DoS). Continued receipt of this specific multicast traffic will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on QFX5000 and EX4600 Series: All versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R3-S5; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R3-S3; 20.1 versions prior to 20.1R2-S2, 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R2-S2, 20.4R3; 21.1 versions prior to 21.1R1-S1, 21.1R2.

In an MPLS P2MP environment a Loop with Unreachable Exit Condition vulnerability in the routing protocol daemon (RPD) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated adjacent attacker to cause high load on RPD which in turn may lead to routing protocol flaps. If a system with sensor-based-stats enabled receives a specific LDP FEC this can lead to the above condition. Continued receipted of such an LDP FEC will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS 19.2 version 19.2R2 and later versions prior to 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3-S2; 20.1 versions prior to 20.1R2-S1, 20.1R3; 20.2 versions prior to 20.2R2-S1, 20.2R3; 20.3 versions prior to 20.3R1-S2, 20.3R2. This issue does not affect Juniper Networks Junos OS versions prior to 19.2R2. Juniper Networks Junos OS Evolved All versions prior to 20.1R2-S3-EVO; 20.3 versions prior to 20.3R1-S2-EVO.

A Missing Release of Memory after Effective Lifetime vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on PTX Series allows an adjacent attacker to cause a Denial of Service (DoS) by sending genuine BGP flowspec packets which cause an FPC heap memory leak. Once having run out of memory the FPC will crash and restart along with a core dump. Continued receipted of these packets will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS All versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S7; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R3-S6; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3-S1; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2. Juniper Networks Junos Evolved is not affected.

An Unchecked Return Value vulnerability in the authd (authentication daemon) of Juniper Networks Junos OS on MX Series configured for subscriber management / BBE allows an adjacent attacker to cause a crash by sending a specific username. This impacts authentication, authorization, and accounting (AAA) services on the MX devices and leads to a Denial of Service (DoS) condition. Continued receipted of these PPP login request will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS 15.1 versions prior to 15.1R7-S9; 17.3 versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R3-S3; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S1; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2.

An Improper Control of a Resource Through its Lifetime vulnerability in Packet Forwarding Engine (PFE) of Juniper Networks Junos OS and Junos OS Evolved allows unauthenticated adjacent attacker to cause a Denial of Service (DoS). In an EVPN-MPLS scenario, if MAC is learned locally on an access interface but later a request to delete is received indicating that the MAC was learnt remotely, this can lead to memory corruption which can result in line card crash and reload. This issue affects: Juniper Networks Junos OS All versions 17.3R1 and later versions prior to 19.2R3-S5; 19.3 versions prior to 19.3R3-S5; 19.4 versions prior to 19.4R2-S6, 19.4R3-S8; 20.1 version 20.1R1 and later versions; 20.2 versions prior to 20.2R3-S4; 20.3 versions prior to 20.3R3-S3; 20.4 versions prior to 20.4R3-S3; 21.1 versions prior to 21.1R3-S1; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R2; 21.4 versions prior to 21.4R1-S1, 21.4R2. Juniper Networks Junos OS Evolved All versions prior to 20.4R3-S3-EVO; 21.1-EVO version 21.1R1-EVO and later versions; 21.2-EVO versions prior to 21.2R3-EVO; 21.3-EVO versions prior to 21.3R2-EVO; 21.4-EVO versions prior to 21.4R1-S1-EVO, 21.4R2-EVO. This issue does not affect Juniper Networks Junos OS versions prior to 17.3R1.

A Race Condition vulnerability in Juniper Networks Junos OS LLDP implementation allows an attacker to cause LLDP to crash leading to a Denial of Service (DoS). This issue occurs when crafted LLDP packets are received by the device from an adjacent device. Multiple LACP flaps will occur after LLDP crashes. An indicator of compromise is to evaluate log file details for lldp with RLIMIT. Intervention should occur before 85% threshold of used KB versus maximum available KB memory is reached. show log messages | match RLIMIT | match lldp | last 20 Matching statement is " /kernel: %KERNEL-[number]: Process ([pid #],lldpd) has exceeded 85% of RLIMIT_DATA: " with [] as variable data to evaluate for. This issue affects: Juniper Networks Junos OS: 12.3 versions prior to 12.3R12-S15; 12.3X48 versions prior to 12.3X48-D95; 15.1 versions prior to 15.1R7-S6; 15.1X49 versions prior to 15.1X49-D200; 15.1X53 versions prior to 15.1X53-D593; 16.1 versions prior to 16.1R7-S7; 17.1 versions prior to 17.1R2-S11, 17.1R3-S2; 17.2 versions prior to 17.2R1-S9, 17.2R3-S3; 17.3 versions prior to 17.3R2-S5, 17.3R3-S6; 17.4 versions prior to 17.4R2-S4, 17.4R3; 18.1 versions prior to 18.1R3-S5; 18.2 versions prior to 18.2R2-S7, 18.2R3; 18.2X75 versions prior to 18.2X75-D12, 18.2X75-D33, 18.2X75-D50, 18.2X75-D420; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R1-S5, 18.4R2; 19.1 versions prior to 19.1R1-S4, 19.1R2.

An Improper Input Validation vulnerability in the VxLAN packet forwarding engine (PFE) of Juniper Networks Junos OS on QFX5000 Series, EX4600 Series devices allows an unauthenticated, adjacent attacker, sending two or more genuine packets in the same VxLAN topology to possibly cause a DMA memory leak to occur under various specific operational conditions. The scenario described here is the worst-case scenario. There are other scenarios that require operator action to occur. An indicator of compromise may be seen when multiple devices indicate that FPC0 has gone missing when issuing a show chassis fpc command for about 10 to 20 minutes, and a number of interfaces have also gone missing. Use the following command to determine if FPC0 has gone missing from the device. show chassis fpc detail This issue affects: Juniper Networks Junos OS on QFX5000 Series, EX4600 Series: * 18.4 version 18.4R2 and later versions prior to 20.4R3-S8; * 21.1 version 21.1R1 and later versions prior to 21.2R3-S6; * 21.3 versions prior to 21.3R3-S5; * 21.4 versions prior to 21.4R3-S4; * 22.1 versions prior to 22.1R3-S3; * 22.2 versions prior to 22.2R3-S1; * 22.3 versions prior to 22.3R2-S2, 22.3R3; * 22.4 versions prior to 22.4R2.

An Improper Validation of Syntactic Correctness of Input vulnerability in Routing Protocol Daemon (rpd) Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network based attacker to cause a Denial of Service (DoS). When a malformed BGP UPDATE packet is received over an established BGP session, the rpd crashes and restarts. This issue affects both eBGP and iBGP implementations. This issue affects: Juniper Networks Junos OS * 21.4 versions prior to 21.4R3-S4; * 22.1 versions prior to 22.1R3-S3; * 22.2 versions prior to 22.2R3-S2; * 22.3 versions prior to 22.3R2-S2, 22.3R3; * 22.4 versions prior to 22.4R2-S1, 22.4R3; * 23.2 versions prior to 23.2R1, 23.2R2; Juniper Networks Junos OS Evolved * 21.4 versions prior to 21.4R3-S5-EVO; * 22.1 versions prior to 22.1R3-S3-EVO; * 22.2 versions prior to 22.2R3-S3-EVO; * 22.3 versions prior to 22.3R2-S2-EVO; * 22.4 versions prior to 22.4R3-EVO; * 23.2 versions prior to 23.2R2-EVO;

An Expired Pointer Dereference vulnerability in Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, adjacent attacker to cause Denial of Service (DoS).On all Junos OS and Junos OS Evolved platforms, when an MPLS Label-Switched Path (LSP) is configured with node-link-protection and transport-class, and an LSP flaps, rpd crashes and restarts. Continuous flapping of LSP can cause a sustained Denial of Service (DoS) condition. This issue affects: Junos OS: * All versions before 22.2R3-S4, * 22.4 versions before 22.4R3-S2, * 23.2 versions before 23.2R2, * 23.4 versions before 23.4R2. Junos OS Evolved: * All versions before 22.2R3-S4-EVO, * 22.4-EVO versions before 22.4R3-S2-EVO, * 23.2-EVO versions before 23.2R2-EVO, * 23.4-EVO versions before 23.4R2-EVO.

A Signed to Unsigned Conversion Error vulnerability in the Layer 2 Control Protocol daemon (l2cpd) of Juniper Networks Junos OS and Juniper Networks Junos OS Evolved allows an unauthenticated adjacent attacker sending a specifically malformed LLDP TLV to cause the l2cpd process to crash and restart, causing a Denial of Service (DoS).  Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. When an LLDP telemetry subscription is active, receipt of a specifically malformed LLDP TLV causes the l2cpd process to crash and restart. This issue affects: Junos OS: * All versions before 21.2R3-S9,  * from 21.4 before 21.4R3-S10,  * from 22.2 before 22.2R3-S6,  * from 22.4 before 22.4R3-S6,  * from 23.2 before 23.2R2-S3,  * from 23.4 before 23.4R2-S4,  * from 24.2 before 24.2R2;  Junos OS Evolved:  * All versions before 21.4R3-S10-EVO, * from 22.2-EVO before 22.2R3-S6-EVO,  * from 22.4-EVO before 22.4R3-S6-EVO,  * from 23.2-EVO before 23.2R2-S3-EVO,  * from 23.4-EVO before 23.4R2-S4-EVO,  * from 24.2-EVO before 24.2R2-EVO.