On EX2300, EX3400, EX4600, QFX3K and QFX5K series, firewall filter configuration cannot perform packet matching on any IPv6 extension headers. This issue may allow IPv6 packets that should have been blocked to be forwarded. IPv4 packet filtering is unaffected by this vulnerability. Affected releases are Juniper Networks Junos OS on EX and QFX series;: 14.1X53 versions prior to 14.1X53-D47; 15.1 versions prior to 15.1R7; 15.1X53 versions prior to 15.1X53-D234 on QFX5200/QFX5110 series; 15.1X53 versions prior to 15.1X53-D591 on EX2300/EX3400 series; 16.1 versions prior to 16.1R7; 17.1 versions prior to 17.1R2-S10, 17.1R3; 17.2 versions prior to 17.2R3; 17.3 versions prior to 17.3R3; 17.4 versions prior to 17.4R2; 18.1 versions prior to 18.1R2.

On EX4300 Series switches with TCAM optimization enabled, incoming multicast traffic matches an implicit loopback filter rule first, since it has high priority. This rule is meant for reserved multicast addresses 224.0.0.x, but incorrectly matches on 224.x.x.x. Due to this bug, when a firewall filter is applied on the loopback interface, other firewall filters might stop working for multicast traffic. The command 'show firewall filter' can be used to confirm whether the filter is working. This issue only affects the EX4300 switch. No other products or platforms are affected by this vulnerability. This issue affects: Juniper Networks Junos OS: 14.1X53 versions prior to 14.1X53-D51, 14.1X53-D115 on EX4300 Series; 17.1 versions prior to 17.1R3 on EX4300 Series; 17.2 versions prior to 17.2R3-S2 on EX4300 Series; 17.3 versions prior to 17.3R3-S3 on EX4300 Series; 17.4 versions prior to 17.4R2-S5, 17.4R3 on EX4300 Series; 18.1 versions prior to 18.1R3-S1 on EX4300 Series; 18.2 versions prior to 18.2R2 on EX4300 Series; 18.3 versions prior to 18.3R2 on EX4300 Series.

An Unsupported Feature in the UI vulnerability in Juniper Networks Junos OS on MX Series and EX9200 Series allows an unauthenticated, network-based attacker to cause partial impact to the integrity of the device. If the "tcp-reset" option is added to the "reject" action in an IPv6 filter which matches on "payload-protocol", packets are permitted instead of rejected. This happens because the payload-protocol match criteria is not supported in the kernel filter causing it to accept all packets without taking any other action. As a fix the payload-protocol match will be treated the same as a "next-header" match to avoid this filter bypass. This issue doesn't affect IPv4 firewall filters. This issue affects Juniper Networks Junos OS on MX Series and EX9200 Series: * All versions earlier than 20.4R3-S7; * 21.1 versions earlier than 21.1R3-S5; * 21.2 versions earlier than 21.2R3-S5; * 21.3 versions earlier than 21.3R3-S4; * 21.4 versions earlier than 21.4R3-S4; * 22.1 versions earlier than 22.1R3-S2; * 22.2 versions earlier than 22.2R3-S2; * 22.3 versions earlier than 22.3R2-S2, 22.3R3; * 22.4 versions earlier than 22.4R1-S2, 22.4R2-S2, 22.4R3.

A Use of Incorrect Operator vulnerability in the Routing Engine firewall of Juniper Networks Junos OS Evolved allows an unauthenticated, network-based attacker to bypass security restrictions. When a firewall filter which is applied to the lo0 or re:mgmt interface references a prefix list with 'from prefix-list', and that prefix list contains more than 10 entries, the prefix list doesn't match and packets destined to or from the local device are not filtered. This issue affects firewall filters applied to the re:mgmt interfaces as input and output, but only affects firewall filters applied to the lo0 interface as output. This issue is applicable to IPv4 and IPv6 as a prefix list can contain IPv4 and IPv6 prefixes. This issue affects Junos OS Evolved: * 23.2R2-S3-EVO versions before 23.2R2-S4-EVO, * 23.4R2-S3-EVO versions before 23.4R2-S5-EVO, * 24.2R2-EVO versions before 24.2R2-S1-EVO, * 24.4-EVO versions before 24.4R1-S3-EVO, 24.4R2-EVO. This issue doesn't affect Junos OS Evolved versions before 23.2R1-EVO.

A Missing Authentication for Critical Function vulnerability in Juniper Networks Junos OS on SRX Series allows an unauthenticated, network-based attacker to cause limited impact to the file system integrity. With a specific request to user.php that doesn't require authentication an attacker is able to upload arbitrary files via J-Web, leading to a loss of integrity for a certain  part of the file system, which may allow chaining to other vulnerabilities. This issue affects Juniper Networks Junos OS on SRX Series: * All versions prior to 20.4R3-S8; * 21.1 versions 21.1R1 and later; * 21.2 versions prior to 21.2R3-S6; * 21.3 versions prior to 21.3R3-S5; * 21.4 versions prior to 21.4R3-S5; * 22.1 versions prior to 22.1R3-S3; * 22.2 versions prior to 22.2R3-S2; * 22.3 versions prior to 22.3R2-S2, 22.3R3; * 22.4 versions prior to 22.4R2-S1, 22.4R3.

A Missing Authentication for Critical Function vulnerability in Juniper Networks Junos OS on SRX Series allows an unauthenticated, network-based attacker to cause limited impact to the file system integrity. With a specific request to webauth_operation.php that doesn't require authentication, an attacker is able to upload and download arbitrary files via J-Web, leading to a loss of integrity or confidentiality, which may allow chaining to other vulnerabilities. This issue affects Juniper Networks Junos OS on SRX Series: * 21.2 versions prior to 21.2R3-S8; * 21.4 versions prior to 21.4R3-S6; * 22.1 versions prior to 22.1R3-S5; * 22.2 versions prior to 22.2R3-S3; * 22.3 versions prior to 22.3R3-S2; * 22.4 versions prior to 22,4R2-S2, 22.4R3; * 23.2 versions prior to 23.2R1-S2, 23.2R2.

The stateless firewall in Juniper Junos 13.3R3, 14.1R1, and 14.1R2, when using Trio-based PFE modules, does not properly match ports, which might allow remote attackers to bypass firewall rule.

After Junos OS device reboot or upgrade, the stateless firewall filter configuration may not take effect. This issue can be verified by running the command: user@re0> show interfaces <interface_name> extensive | match filters" CAM destination filters: 0, CAM source filters: 0 Note: when the issue occurs, it does not show the applied firewall filter. The correct output should show the applied firewall filter, for example: user@re0> show interfaces <interface_name> extensive | match filters" CAM destination filters: 0, CAM source filters: 0 Input Filters: FIREWAL_FILTER_NAME-<interface_name> This issue affects firewall filters for every address family. Affected releases are Juniper Networks Junos OS: 15.1R4, 15.1R5, 15.1R6 and SRs based on these MRs. 15.1X8 versions prior to 15.1X8.3.

An Improper Check for Unusual or Exceptional Conditions in Juniper Networks Junos OS Evolved may cause the stateless firewall filter configuration which uses the action 'policer' in certain combinations with other options to not take effect. An administrator can use the following CLI command to see the failures with filter configuration: user@device> show log kfirewall-agent.log | match ERROR Jul 23 14:16:03 ERROR: filter not supported This issue affects Juniper Networks Junos OS Evolved: Versions 19.1R1-EVO and above prior to 20.3R1-S2-EVO, 20.3R2-EVO. This issue does not affect Juniper Networks Junos OS.

An Improperly Controlled Sequential Memory Allocation vulnerability in the Juniper Networks Deep Packet Inspection-Decoder (JDPI-Decoder) Application Signature component of Junos OS's AppID service on SRX Series devices will stop the JDPI-Decoder from identifying dynamic application traffic, allowing an unauthenticated network-based attacker to send traffic to the target device using the JDPI-Decoder, designed to inspect dynamic application traffic and take action upon this traffic, to instead begin to not take action and to pass the traffic through. An example session can be seen by running the following command and evaluating the output. user@device# run show security flow session source-prefix <address/mask> extensive Session ID: <session ID>, Status: Normal, State: Active Policy name: <name of policy> Dynamic application: junos:UNKNOWN, <<<<< LOOK HERE Please note, the JDPI-Decoder and the AppID SigPack are both affected and both must be upgraded along with the operating system to address the matter. By default, none of this is auto-enabled for automatic updates. This issue affects: Juniper Networks any version of the JDPI-Decoder Engine prior to version 5.7.0-47 with the JDPI-Decoder enabled using any version of the AppID SigPack prior to version 1.550.2-31 (SigPack 3533) on Junos OS on SRX Series: All versions prior to 19.1R3-S10; 19.2 versions prior to 19.2R3-S7; 19.3 versions prior to 19.3R3-S8; 19.4 versions prior to 19.4R3-S11; 20.1 version 20.1R1 and later versions prior to 20.2R3-S7; 20.3 version 20.3R1 and later versions prior to 20.4R3-S6; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S4; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3-S3; 22.1 versions prior to 22.1R3-S1; 22.2 versions prior to 22.2R2-S1, 22.2R3; 22.3 versions prior to 22.3R1-S2, 22.3R2;

An Improper Handling of Unexpected Data Type vulnerability in IPv6 firewall filter processing of Juniper Networks Junos OS on the ACX Series devices will prevent a firewall filter with the term 'from next-header ah' from being properly installed in the packet forwarding engine (PFE). There is no immediate indication of an incomplete firewall filter commit shown at the CLI, which could allow an attacker to send valid packets to or through the device that were explicitly intended to be dropped. An indication that the filter was not installed can be identified with the following logs: fpc0 ACX_DFW_CFG_FAILED: ACX Error (dfw):dnx_dfw_rule_prepare : Config failed: Unsupported Ip-protocol 51 in the filter lo0.0-inet6-i fpc0 ACX_DFW_CFG_FAILED: ACX Error (dfw):dnx_dfw_rule_prepare : Please detach the filter, remove unsupported match and re-attach fpc0 ACX_DFW_CFG_FAILED: ACX Error (dfw):dnx_dfw_process_rule : Status:104 dnx_dfw_rule_prepare failed fpc0 ACX_DFW_CFG_FAILED: ACX Error (dfw):dnx_dfw_process_filter : Status:104 dnx_dfw_process_rule failed fpc0 ACX_DFW_CFG_FAILED: ACX Error (dfw):dnx_dfw_update_filter_in_hw : Status:104 Could not process filter(lo0.0-inet6-i) for rule expansion Unsupported match, action present. fpc0 ACX_DFW_CFG_FAILED: ACX Error (dfw):dnx_dfw_create_hw_instance : Status:104 Could not program dfw(lo0.0-inet6-i) type(IFP_DFLT_INET6_Lo0_FILTER)! [104] fpc0 ACX_DFW_CFG_FAILED: ACX Error (dfw):dnx_dfw_bind_shim : [104] Could not create dfw(lo0.0-inet6-i) type(IFP_DFLT_INET6_Lo0_FILTER) fpc0 ACX_DFW_CFG_FAILED: ACX Error (dfw):dnx_dfw_update_resolve : [100] Failed to bind filter(3) to bind point fpc0 ACX_DFW_CFG_FAILED: ACX Error (dfw):dnx_dfw_change_end : dnx_dfw_update_resolve (resolve type) failed This issue affects Juniper Networks Junos OS on ACX Series: All versions prior to 20.2R3-S7; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S4; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2.

An Improper Authentication vulnerability in upload-file.php, used by the J-Web component of Juniper Networks Junos OS allows an unauthenticated, network-based attacker to upload arbitrary files to temporary folders on the device. This issue affects Juniper Networks Junos OS: All versions prior to 19.4R3-S11; 20.1 version 20.1R1 and later versions; 20.2 versions prior to 20.2R3-S7; 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3-S6; 21.1 version 21.1R1 and later versions; 21.2 versions prior to 21.2R3-S4; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3-S3; 22.1 versions prior to 22.1R3-S1; 22.2 versions prior to 22.2R2-S1, 22.2R3; 22.3 versions prior to 22.3R1-S2, 22.3R2.

An Improper Initialization vulnerability in Juniper Networks Junos OS Evolved may cause a commit operation for disabling the telnet service to not take effect as expected, resulting in the telnet service staying enabled. When it is not intended to be operating on the device, an administrator can issue the following command to verify whether telnet is operating in the background: user@device > show system connections | grep :23 tcp 0 0 0.0.0.0:23 0.0.0.0:* LISTEN 20879/xinetd This issue affects: Juniper Networks Junos OS Evolved All versions prior to 20.4R2-S2-EVO; 21.1 version 21.1R1-EVO and later versions; 21.2 versions prior to 21.2R2-EVO.

A firewall bypass vulnerability in the host based firewall of Juniper Networks Junos Space versions prior to 16.1R1 may permit certain crafted packets, representing a network integrity risk.

A Missing Authentication for Critical Function vulnerability in Juniper Networks Junos OS on EX Series allows an unauthenticated, network-based attacker to cause limited impact to the file system integrity. With a specific request to installAppPackage.php that doesn't require authentication an attacker is able to upload arbitrary files via J-Web, leading to a loss of integrity for a certain part of the file system, which may allow chaining to other vulnerabilities. This issue affects Juniper Networks Junos OS on EX Series: * All versions prior to 20.4R3-S8; * 21.1 versions 21.1R1 and later; * 21.2 versions prior to 21.2R3-S6; * 21.3 versions prior to 21.3R3-S5; * 21.4 versions prior to 21.4R3-S4; * 22.1 versions prior to 22.1R3-S3; * 22.2 versions prior to 22.2R3-S1; * 22.3 versions prior to 22.3R2-S2, 22.3R3; * 22.4 versions prior to 22.4R2-S1, 22.4R3.

On EX4300, EX4600, QFX3500, and QFX5100 Series, a vulnerability in the IP firewall filter component may cause the firewall filter evaluation of certain packets to fail. This issue only affects firewall filter evaluation of certain packets destined to the device Routing Engine (RE). This issue does not affect the Layer 2 firewall filter evaluation nor does it affect the Layer 3 firewall filter evaluation destined to connected hosts. This issue may occur when evaluating both IPv4 or IPv6 packets. This issue affects Juniper Networks Junos OS: 14.1X53 versions prior to 14.1X53-D12 on QFX5100 Series and EX4600 Series; 14.1X53 versions prior to 14.1X53-D52 on QFX3500 Series; 14.1X53 versions prior to 14.1X53-D48 on EX4300 Series; 15.1 versions prior to 15.1R7-S3 on EX4300 Series; 16.1 versions prior to 16.1R7 on EX4300 Series; 17.1 versions prior to 17.1R3 on EX4300 Series; 17.2 versions prior to 17.2R3 on EX4300 Series; 17.3 versions prior to 17.3R2-S5, 17.3R3 on EX4300 Series; 17.4 versions prior to 17.4R2 on EX4300 Series; 18.1 versions prior to 18.1R3 on EX4300 Series; 18.2 versions prior to 18.2R2 on EX4300 Series.

When configuring stateless firewall filters in Juniper Networks EX4600 and QFX 5000 Series devices using Virtual Extensible LAN protocol (VXLAN), the discard action will fail to discard traffic under certain conditions. Given a firewall filter configuration similar to: family ethernet-switching { filter L2-VLAN { term ALLOW { from { user-vlan-id 100; } then { accept; } } term NON-MATCH { then { discard; } } when there is only one term containing a 'user-vlan-id' match condition, and no other terms in the firewall filter except discard, the discard action for non-matching traffic will only discard traffic with the same VLAN ID specified under 'user-vlan-id'. Other traffic (e.g. VLAN ID 200) will not be discarded. This unexpected behavior can lead to unintended traffic passing through the interface where the firewall filter is applied. This issue only affects systems using VXLANs. This issue affects Juniper Networks Junos OS on QFX5K Series: 18.1 versions prior to 18.1R3-S7, except 18.1R3; 18.2 versions prior to 18.2R2-S7, 18.2R3-S1; 18.3 versions prior to 18.3R1-S5, 18.3R2-S4, 18.3R3; 18.4 versions prior to 18.4R1-S7, 18.4R2-S1, 18.4R3; 19.1 versions prior to 19.1R1-S5, 19.1R2; 19.2 versions prior to 19.2R1-S5, 19.2R2.

A PHP External Variable Modification vulnerability in J-Web of Juniper Networks Junos OS on EX Series allows an unauthenticated, network-based attacker to control certain, important environment variables. Using a crafted request an attacker is able to modify certain PHP environment variables leading to partial loss of integrity, which may allow chaining to other vulnerabilities. This issue affects Juniper Networks Junos OS on EX Series: * All versions prior to 20.4R3-S9; * 21.1 versions 21.1R1 and later; * 21.2 versions prior to 21.2R3-S7; * 21.3 versions prior to 21.3R3-S5; * 21.4 versions prior to 21.4R3-S5; * 22.1 versions prior to 22.1R3-S4; * 22.2 versions prior to 22.2R3-S2; * 22.3 versions prior to 22.3R3-S1; * 22.4 versions prior to 22.4R2-S2, 22.4R3; * 23.2 versions prior to 23.2R1-S1, 23.2R2.

An Exposure of Resource to Wrong Sphere vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on MX Series allows an unauthenticated, network-based attacker to bypass the intended access restrictions. In an Abstracted Fabric (AF) scenario if routing-instances (RI) are configured, specific valid traffic destined to the device can bypass the configured lo0 firewall filters as it's received in the wrong RI context. This issue affects Juniper Networks Junos OS on MX Series: * All versions earlier than 20.4R3-S9; * 21.2 versions earlier than 21.2R3-S3; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R3; * 22.2 versions earlier than 22.2R3; * 22.3 versions earlier than 22.3R2.

An Improper Input Validation weakness allows a malicious local attacker to elevate their permissions to take control of other portions of the NFX platform they should not be able to access, and execute commands outside their authorized scope of control. This leads to the attacker being able to take control of the entire system. This issue affects: Juniper Networks Junos OS versions prior to 18.2R1 on NFX Series.

Juniper Junos OS before 12.1X46-D45, 12.1X47 before 12.1X47-D30, 12.1X48 before 12.3X48-D20, and 15.1X49 before 15.1X49-D30 on SRX series devices, when the Real Time Streaming Protocol Application Layer Gateway (RTSP ALG) is enabled, allow remote attackers to cause a denial of service (flowd crash) via a crafted RTSP packet.

The administrative web services interface in Juniper ScreenOS before 6.3.0r21 allows remote attackers to cause a denial of service (reboot) via a crafted SSL packet.

Juniper Junos OS before 12.1X46-D45, 12.1X47 before 12.1X47-D30, 12.3 before 12.3R11, 12.3X48 before 12.3X48-D25, 13.2 before 13.2R8, 13.3 before 13.3R7, 14.1 before 14.1R6, 14.2 before 14.2R4, 15.1 before 15.1R1 or 15.1F2, and 15.1X49 before 15.1X49-D15 allow local users to gain privileges via crafted combinations of CLI commands and arguments, a different vulnerability than CVE-2015-3003, CVE-2014-3816, and CVE-2014-0615.

The Juniper Junos Pulse Secure Access Service (SSL VPN) devices with IVE OS 8.0 before 8.0r1, 7.4 before 7.4r5, and 7.1 before 7.1r18 allows remote attackers to conduct clickjacking attacks via unspecified vectors.

Embedthis Appweb, as used in J-Web in Juniper Junos OS before 12.1X44-D60, 12.1X46 before 12.1X46-D45, 12.1X47 before 12.1X47-D30, 12.3 before 12.3R10, 12.3X48 before 12.3X48-D20, 13.2X51 before 13.2X51-D20, 13.3 before 13.3R8, 14.1 before 14.1R6, and 14.2 before 14.2R5, allows remote attackers to cause a denial of service (J-Web crash) via unspecified vectors.

Juniper Junos OS before 12.1X46-D45, 12.1X46-D50, 12.1X47 before 12.1X47-D35, 12.3X48 before 12.3X48-D30, 13.3 before 13.3R9-S1, 14.1 before 14.1R7, 14.2 before 14.2R6, 15.1 before 15.1F2-S5, 15.1F4 before 15.1F4-S2, 15.1R before 15.1R2-S3, 15.1 before 15.1R3, and 15.1X49 before 15.1X49-D40 allow remote attackers to cause a denial of service (kernel crash) via a crafted UDP packet destined to the interface IP address of a 64-bit OS device.

Juniper Junos OS before 12.1X46-D50, 12.1X47 before 12.1X47-D40, 12.3X48 before 12.3X48-D30, 13.3 before 13.3R9, 14.1 before 14.1R8, 14.1X53 before 14.1X53-D40, 14.2 before 14.2R6, 15.1 before 15.1F6 or 15.1R3, and 15.1X49 before 15.1X49-D40, when configured with a GRE or IPIP tunnel, allow remote attackers to cause a denial of service (kernel panic) via a crafted ICMP packet.

Open redirect vulnerability in dana/home/homepage.cgi in Juniper Networks IVE 6.5R1 (Build 14599) and 6.5R2 (Build 14951) allows remote attackers to redirect users to arbitrary web sites and conduct phishing attacks via a URL in the Location parameter.

An Improper Input Validation vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). When a BGP update message is received over an established BGP session, and that message contains a specific, optional transitive attribute, this session will be torn down with an update message error. This issue cannot propagate beyond an affected system as the processing error occurs as soon as the update is received. This issue is exploitable remotely as the respective attribute can propagate through unaffected systems and intermediate AS (if any). Continuous receipt of a BGP update containing this attribute will create a sustained Denial of Service (DoS) condition. Some customers have experienced these BGP session flaps which prompted Juniper SIRT to release this advisory out of cycle before fixed releases are widely available as there is an effective workaround. This issue affects: Juniper Networks Junos OS 15.1R1 and later versions prior to 20.4R3-S8; 21.1 version 21.1R1 and later versions prior to 21.2R3-S6; 21.3 versions prior to 21.3R3-S5; 21.4 versions prior to 21.4R3-S4; 22.1 versions prior to 22.1R3-S4; 22.2 versions prior to 22.2R3-S2; 22.3 versions prior to 22.3R2-S2, 22.3R3-S1; 22.4 versions prior to 22.4R2-S1, 22.4R3; 23.1 versions prior to 23.1R1-S1, 23.1R2. Juniper Networks Junos OS Evolved All versions prior to 20.4R3-S8-EVO; 21.1 version 21.1R1-EVO and later versions prior to 21.2R3-S6-EVO; 21.3 versions prior to 21.3R3-S5-EVO; 21.4 versions prior to 21.4R3-S4-EVO; 22.1 versions prior to 22.1R3-S4-EVO; 22.2 versions prior to 22.2R3-S2-EVO; 22.3 versions prior to 22.3R2-S2-EVO, 22.3R3-S1-EVO; 22.4 versions prior to 22.4R2-S1-EVO, 22.4R3-EVO; 23.1 versions prior to 23.1R1-S1-EVO, 23.1R2-EVO.

Juniper ScreenOS before 6.3.0r21, when ssh-pka is configured and enabled, allows remote attackers to cause a denial of service (system crash) or execute arbitrary code via crafted SSH negotiation.

Juniper chassis with Trio (Trinity) chipset line cards and Junos OS 13.3 before 13.3R8, 14.1 before 14.1R6, 14.2 before 14.2R5, and 15.1 before 15.1R2 allow remote attackers to cause a denial of service (MPC line card crash) via a crafted uBFD packet.

An Improper Input Validation vulnerability in Juniper Tunnel Driver (jtd) and ICMP module of Juniper Networks Junos OS Evolved allows an unauthenticated attacker within the MPLS administrative domain to send specifically crafted packets to the Routing Engine (RE) to cause a Denial of Service (DoS).  When specifically crafted transit MPLS IPv4 packets are received by the Packet Forwarding Engine (PFE), these packets are internally forwarded to the RE. Continued receipt of these packets may create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS: * All versions before 21.2R3-S8-EVO; * from 21.4-EVO before 21.4R3-S6-EVO; * from 22.2-EVO before 22.2R3-S4-EVO; * from 22.3-EVO before 22.3R3-S3-EVO; * from 22.4-EVO before 22.4R3-EVO; * from 23.2-EVO before 23.2R2-EVO. * from 23.4-EVO before 23.4R1-S1-EVO.

The L2TP packet processing functionality in Juniper Netscreen and ScreenOS Firewall products with ScreenOS before 6.3.0r13-dnd1, 6.3.0r14 through 6.3.0r18 before 6.3.0r18-dnc1, and 6.3.0r19 allows remote attackers to cause a denial of service via a crafted L2TP packet.

An Improper Input Validation vulnerability in J-Web of Juniper Networks Junos OS allows a locally authenticated J-Web attacker to escalate their privileges to root over the target device. This issue affects: Juniper Networks Junos OS All versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R3-S3; 19.3 versions prior to 19.3R3-S3; 19.4 versions prior to 19.4R3-S5; 20.1 versions prior to 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2, 21.1R3; 21.2 versions prior to 21.2R1-S1, 21.2R2;

The Routing Engine in Juniper Junos OS 13.2R5 through 13.2R8, 13.3R1 before 13.3R8, 13.3R7 before 13.3R7-S3, 14.1R1 before 14.1R6, 14.1R3 before 14.1R3-S9, 14.1R4 before 14.1R4-S7, 14.1X51 before 14.1X51-D65, 14.1X53 before 14.1X53-D12, 14.1X53 before 14.1X53-D28, 14.1X53 before 4.1X53-D35, 14.2R1 before 14.2R5, 14.2R3 before 14.2R3-S4, 14.2R4 before 14.2R4-S1, 15.1 before 15.1R3, 15.1F2 before 15.1F2-S2, and 15.1X49 before 15.1X49-D40, when LDP is enabled, allows remote attackers to cause a denial of service (RPD routing process crash) via a crafted LDP packet.

An Improper Input Validation vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). When certain specific crafted BGP UPDATE messages are received over an established BGP session, one BGP session may be torn down with an UPDATE message error, or the issue may propagate beyond the local system which will remain non-impacted, but may affect one or more remote systems. This issue is exploitable remotely as the crafted UPDATE message can propagate through unaffected systems and intermediate BGP speakers. Continuous receipt of the crafted BGP UPDATE messages will create a sustained Denial of Service (DoS) condition for impacted devices. This issue affects eBGP and iBGP, in both IPv4 and IPv6 implementations. This issue requires a remote attacker to have at least one established BGP session. Improper Input Validation, Denial of Service vulnerability in Juniper Networks, Inc. Junos OS (BGP, rpd modules), Juniper Networks, Inc. Junos OS Evolved (BGP, rpd modules) allows Fuzzing.This issue affects  Junos OS:  * All versions before 20.4R3-S10, * from 21.1R1 through 21.*, * from 21.2 before 21.2R3-S5, * from 21.3 before 21.3R3-S5, * from 21.4 before 21.4R3-S7 (unaffected from 21.4R3-S5, affected from 21.4R3-S6) * from 22.1 before 22.1R3-S4, * from 22.2 before 22.2R3-S3, * from 22.3 before 22.3R3-S1, * from 22.4 before 22.4R3, * from 23.2 before 23.2R2. Junos OS Evolved: * All versions before 20.4R3-S10-EVO, * from 21.2-EVO before 21.2R3-S7-EVO, * from 21.3-EVO before 21.3R3-S5-EVO, * from 21.4-EVO before 21.4R3-S5-EVO, * from 22.1-EVO before 22.1R3-S4-EVO, * from 22.2-EVO before 22.2R3-S3-EVO, * from 22.3-EVO before 22.3R3-S1-EVO, * from 22.4-EVO before 22.4R3-EVO, * from 23.2-EVO before 23.2R2-EVO.

An Improper Input Validation vulnerability in the routing protocol daemon (rpd) of Juniper Networks allows an attacker to cause a Denial of Service (DoS )to the device upon receiving and processing a specific malformed ISO VPN BGP UPDATE packet. Continued receipt of this packet will cause a sustained Denial of Service condition. This issue affects: * Juniper Networks Junos OS: * All versions prior to 20.4R3-S6; * 21.1 versions prior to 21.1R3-S5; * 21.2 versions prior to 21.2R3-S4; * 21.3 versions prior to 21.3R3-S3; * 21.4 versions prior to 21.4R3-S3; * 22.1 versions prior to 22.1R2-S2, 22.1R3; * 22.2 versions prior to 22.2R2-S1, 22.2R3; * 22.3 versions prior to 22.3R1-S2, 22.3R2. Juniper Networks Junos OS Evolved: * All versions prior to 20.4R3-S6-EVO; * 21.1-EVO version 21.1R1-EVO and later versions prior to 21.2R3-S4-EVO; * 21.3-EVO versions prior to 21.3R3-S3-EVO; * 21.4-EVO versions prior to 21.4R3-S3-EVO; * 22.1-EVO versions prior to 22.1R3-EVO; * 22.2-EVO versions prior to 22.2R2-S1-EVO, 22.2R3-EVO; * 22.3-EVO versions prior to 22.3R1-S2-EVO, 22.3R2-EVO.

An Improper Input Validation vulnerability in the VxLAN packet forwarding engine (PFE) of Juniper Networks Junos OS on QFX5000 Series, EX4600 Series devices allows an unauthenticated, adjacent attacker, sending two or more genuine packets in the same VxLAN topology to possibly cause a DMA memory leak to occur under various specific operational conditions. The scenario described here is the worst-case scenario. There are other scenarios that require operator action to occur. An indicator of compromise may be seen when multiple devices indicate that FPC0 has gone missing when issuing a show chassis fpc command for about 10 to 20 minutes, and a number of interfaces have also gone missing. Use the following command to determine if FPC0 has gone missing from the device. show chassis fpc detail This issue affects: Juniper Networks Junos OS on QFX5000 Series, EX4600 Series: * 18.4 version 18.4R2 and later versions prior to 20.4R3-S8; * 21.1 version 21.1R1 and later versions prior to 21.2R3-S6; * 21.3 versions prior to 21.3R3-S5; * 21.4 versions prior to 21.4R3-S4; * 22.1 versions prior to 22.1R3-S3; * 22.2 versions prior to 22.2R3-S1; * 22.3 versions prior to 22.3R2-S2, 22.3R3; * 22.4 versions prior to 22.4R2.

An Improper Validation of Syntactic Correctness of Input vulnerability in Routing Protocol Daemon (rpd) Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network based attacker to cause a Denial of Service (DoS). When a malformed BGP UPDATE packet is received over an established BGP session, the rpd crashes and restarts. This issue affects both eBGP and iBGP implementations. This issue affects: Juniper Networks Junos OS * 21.4 versions prior to 21.4R3-S4; * 22.1 versions prior to 22.1R3-S3; * 22.2 versions prior to 22.2R3-S2; * 22.3 versions prior to 22.3R2-S2, 22.3R3; * 22.4 versions prior to 22.4R2-S1, 22.4R3; * 23.2 versions prior to 23.2R1, 23.2R2; Juniper Networks Junos OS Evolved * 21.4 versions prior to 21.4R3-S5-EVO; * 22.1 versions prior to 22.1R3-S3-EVO; * 22.2 versions prior to 22.2R3-S3-EVO; * 22.3 versions prior to 22.3R2-S2-EVO; * 22.4 versions prior to 22.4R3-EVO; * 23.2 versions prior to 23.2R2-EVO;

An Improper Input Validation vulnerability in the syslog stream TCP transport of Juniper Networks Junos OS on MX240, MX480 and MX960 devices with MX-SPC3 Security Services Card allows an unauthenticated, network-based attacker, to send specific spoofed packets to cause a CPU Denial of Service (DoS) to the MX-SPC3 SPUs. Continued receipt and processing of these specific packets will sustain the DoS condition. This issue affects Junos OS: * All versions before 22.2R3-S6, * from 22.4 before 22.4R3-S4, * from 23.2 before 23.2R2-S3, * from 23.4 before 23.4R2-S4, * from 24.2 before 24.2R1-S2, 24.2R2 An indicator of compromise will indicate the SPC3 SPUs utilization has spiked. For example:     user@device> show services service-sets summary Service sets CPU Interface configured Bytes used Session bytes used Policy bytes used utilization "interface" 1 "bytes" (percent%) "sessions" ("percent"%) "bytes" ("percent"%) 99.97 % OVLD <<<<<< look for high CPU usage

An Improper Input Validation vulnerability in the Juniper DHCP Daemon (jdhcpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, adjacent attacker to cause the jdhcpd process to crash resulting in a Denial of Service (DoS). When a specifically malformed DHCP packet is received from a DHCP client, the jdhcpd process crashes, which will lead to the unavailability of the DHCP service and thereby resulting in a sustained DoS. The DHCP process will restart automatically to recover the service. This issue will occur when dhcp-security is enabled.  This issue affects Junos OS:  * All versions before 21.2R3-S9,  * from 21.4 before 21.4R3-S10,  * from 22.2 before 22.2R3-S6,  * from 22.4 before 22.4R3-S6,  * from 23.2 before 23.2R2-S3,  * from 23.4 before 23.4R2-S4,  * from 24.2 before 24.2R2;  Junos OS Evolved:  * from 22.4 before 22.4R3-S6-EVO,  * from 23.2 before 23.2R2-S3-EVO,  * from 23.4 before 23.4R2-S4-EVO,  * from 24.2 before 24.2R2-EVO. .

Juniper WLC devices with WLAN Software releases 8.0.x before 8.0.4, 9.0.x before 9.0.2.11, 9.0.3.x before 9.0.3.5, and 9.1.x before 9.1.1, when "Proxy ARP" or "No Broadcast" features are enabled in a clustered setup, allows remote attackers to cause a denial of service (device disconnect) via unspecified vectors.

The Juniper MX Series routers with Junos 13.3R3 through 13.3Rx before 13.3R6, 14.1 before 14.1R4, 14.1X50 before 14.1X50-D70, and 14.2 before 14.2R2, when configured as a broadband edge (BBE) router, allows remote attackers to cause a denial of service (jpppd crash and restart) by sending a crafted PAP Authenticate-Request after the PPPoE Discovery and LCP phase are complete.

The Enhanced Web Filtering (EWF) in Juniper Junos before 10.4R15, 11.4 before 11.4R9, 12.1 before 12.1R7, 12.1X44 before 12.1X44-D20, 12.1X45 before 12.1X45-D10, and 12.1X46 before 12.1X46-D10, as used in the SRX Series services gateways, allows remote attackers to cause a denial of service (flow daemon crash and restart) via a crafted URL.