A race problem was found in fs/proc/task_mmu.c in the memory management sub-component in the Linux kernel. This issue may allow a local attacker with user privilege to cause a denial of service.

drivers/net/wireless/intel/iwlwifi/pcie/trans.c in the Linux kernel 5.2.14 does not check the alloc_workqueue return value, leading to a NULL pointer dereference.

In the Linux kernel before 5.0, a memory leak exists in sit_init_net() in net/ipv6/sit.c when register_netdev() fails to register sitn->fb_tunnel_dev, which may cause denial of service, aka CID-07f12b26e21a.

An issue was discovered in the Linux kernel before 5.0.6. There is a memory leak issue when idr_alloc() fails in genl_register_family() in net/netlink/genetlink.c.

A data race flaw was found in the Linux kernel, between where con is allocated and con->sock is set. This issue leads to a NULL pointer dereference when accessing con->sock->sk in net/tipc/topsrv.c in the tipc protocol in the Linux kernel.

drivers/gpu/drm/radeon/radeon_display.c in the Linux kernel 5.2.14 does not check the alloc_workqueue return value, leading to a NULL pointer dereference. NOTE: A third-party software maintainer states that the work queue allocation is happening during device initialization, which for a graphics card occurs during boot. It is not attacker controllable and OOM at that time is highly unlikely

In the Linux kernel before 5.1.13, there is a memory leak in drivers/scsi/libsas/sas_expander.c when SAS expander discovery fails. This will cause a BUG and denial of service.

In the Linux kernel, the following vulnerability has been resolved: ext4: fix race condition between ext4_write and ext4_convert_inline_data Hulk Robot reported a BUG_ON: ================================================================== EXT4-fs error (device loop3): ext4_mb_generate_buddy:805: group 0, block bitmap and bg descriptor inconsistent: 25 vs 31513 free clusters kernel BUG at fs/ext4/ext4_jbd2.c:53! invalid opcode: 0000 [#1] SMP KASAN PTI CPU: 0 PID: 25371 Comm: syz-executor.3 Not tainted 5.10.0+ #1 RIP: 0010:ext4_put_nojournal fs/ext4/ext4_jbd2.c:53 [inline] RIP: 0010:__ext4_journal_stop+0x10e/0x110 fs/ext4/ext4_jbd2.c:116 [...] Call Trace: ext4_write_inline_data_end+0x59a/0x730 fs/ext4/inline.c:795 generic_perform_write+0x279/0x3c0 mm/filemap.c:3344 ext4_buffered_write_iter+0x2e3/0x3d0 fs/ext4/file.c:270 ext4_file_write_iter+0x30a/0x11c0 fs/ext4/file.c:520 do_iter_readv_writev+0x339/0x3c0 fs/read_write.c:732 do_iter_write+0x107/0x430 fs/read_write.c:861 vfs_writev fs/read_write.c:934 [inline] do_pwritev+0x1e5/0x380 fs/read_write.c:1031 [...] ================================================================== Above issue may happen as follows: cpu1 cpu2 __________________________|__________________________ do_pwritev vfs_writev do_iter_write ext4_file_write_iter ext4_buffered_write_iter generic_perform_write ext4_da_write_begin vfs_fallocate ext4_fallocate ext4_convert_inline_data ext4_convert_inline_data_nolock ext4_destroy_inline_data_nolock clear EXT4_STATE_MAY_INLINE_DATA ext4_map_blocks ext4_ext_map_blocks ext4_mb_new_blocks ext4_mb_regular_allocator ext4_mb_good_group_nolock ext4_mb_init_group ext4_mb_init_cache ext4_mb_generate_buddy --> error ext4_test_inode_state(inode, EXT4_STATE_MAY_INLINE_DATA) ext4_restore_inline_data set EXT4_STATE_MAY_INLINE_DATA ext4_block_write_begin ext4_da_write_end ext4_test_inode_state(inode, EXT4_STATE_MAY_INLINE_DATA) ext4_write_inline_data_end handle=NULL ext4_journal_stop(handle) __ext4_journal_stop ext4_put_nojournal(handle) ref_cnt = (unsigned long)handle BUG_ON(ref_cnt == 0) ---> BUG_ON The lock held by ext4_convert_inline_data is xattr_sem, but the lock held by generic_perform_write is i_rwsem. Therefore, the two locks can be concurrent. To solve above issue, we add inode_lock() for ext4_convert_inline_data(). At the same time, move ext4_convert_inline_data() in front of ext4_punch_hole(), remove similar handling from ext4_punch_hole().

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix a data-race around sysctl_tcp_thin_linear_timeouts. While reading sysctl_tcp_thin_linear_timeouts, it can be changed concurrently. Thus, we need to add READ_ONCE() to its reader.

In the Linux kernel, the following vulnerability has been resolved: af_unix: Fix a data-race in unix_dgram_peer_wake_me(). unix_dgram_poll() calls unix_dgram_peer_wake_me() without `other`'s lock held and check if its receive queue is full. Here we need to use unix_recvq_full_lockless() instead of unix_recvq_full(), otherwise KCSAN will report a data-race.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix a data-race around sysctl_tcp_notsent_lowat. While reading sysctl_tcp_notsent_lowat, it can be changed concurrently. Thus, we need to add READ_ONCE() to its reader.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix a data-race around sysctl_tcp_probe_interval. While reading sysctl_tcp_probe_interval, it can be changed concurrently. Thus, we need to add READ_ONCE() to its reader.

In the Linux kernel, the following vulnerability has been resolved: raw: Fix a data-race around sysctl_raw_l3mdev_accept. While reading sysctl_raw_l3mdev_accept, it can be changed concurrently. Thus, we need to add READ_ONCE() to its reader.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix data-races around sysctl_tcp_recovery. While reading sysctl_tcp_recovery, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

An issue was discovered in the Linux kernel through 6.0.9. drivers/media/usb/ttusb-dec/ttusb_dec.c has a memory leak because of the lack of a dvb_frontend_detach call.

In the Linux kernel, the following vulnerability has been resolved: icmp: Fix data-races around sysctl. While reading icmp sysctl variables, they can be changed concurrently. So, we need to add READ_ONCE() to avoid data-races.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix a data-race around sysctl_tcp_early_retrans. While reading sysctl_tcp_early_retrans, it can be changed concurrently. Thus, we need to add READ_ONCE() to its reader.

In the Linux kernel, the following vulnerability has been resolved: nbd: fix race between nbd_alloc_config() and module removal When nbd module is being removing, nbd_alloc_config() may be called concurrently by nbd_genl_connect(), although try_module_get() will return false, but nbd_alloc_config() doesn't handle it. The race may lead to the leak of nbd_config and its related resources (e.g, recv_workq) and oops in nbd_read_stat() due to the unload of nbd module as shown below: BUG: kernel NULL pointer dereference, address: 0000000000000040 Oops: 0000 [#1] SMP PTI CPU: 5 PID: 13840 Comm: kworker/u17:33 Not tainted 5.14.0+ #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996) Workqueue: knbd16-recv recv_work [nbd] RIP: 0010:nbd_read_stat.cold+0x130/0x1a4 [nbd] Call Trace: recv_work+0x3b/0xb0 [nbd] process_one_work+0x1ed/0x390 worker_thread+0x4a/0x3d0 kthread+0x12a/0x150 ret_from_fork+0x22/0x30 Fixing it by checking the return value of try_module_get() in nbd_alloc_config(). As nbd_alloc_config() may return ERR_PTR(-ENODEV), assign nbd->config only when nbd_alloc_config() succeeds to ensure the value of nbd->config is binary (valid or NULL). Also adding a debug message to check the reference counter of nbd_config during module removal.

In the Linux kernel, the following vulnerability has been resolved: ice: fix concurrent reset and removal of VFs Commit c503e63200c6 ("ice: Stop processing VF messages during teardown") introduced a driver state flag, ICE_VF_DEINIT_IN_PROGRESS, which is intended to prevent some issues with concurrently handling messages from VFs while tearing down the VFs. This change was motivated by crashes caused while tearing down and bringing up VFs in rapid succession. It turns out that the fix actually introduces issues with the VF driver caused because the PF no longer responds to any messages sent by the VF during its .remove routine. This results in the VF potentially removing its DMA memory before the PF has shut down the device queues. Additionally, the fix doesn't actually resolve concurrency issues within the ice driver. It is possible for a VF to initiate a reset just prior to the ice driver removing VFs. This can result in the remove task concurrently operating while the VF is being reset. This results in similar memory corruption and panics purportedly fixed by that commit. Fix this concurrency at its root by protecting both the reset and removal flows using the existing VF cfg_lock. This ensures that we cannot remove the VF while any outstanding critical tasks such as a virtchnl message or a reset are occurring. This locking change also fixes the root cause originally fixed by commit c503e63200c6 ("ice: Stop processing VF messages during teardown"), so we can simply revert it. Note that I kept these two changes together because simply reverting the original commit alone would leave the driver vulnerable to worse race conditions.

In the Linux kernel, the following vulnerability has been resolved: igmp: Fix data-races around sysctl_igmp_llm_reports. While reading sysctl_igmp_llm_reports, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers. This test can be packed into a helper, so such changes will be in the follow-up series after net is merged into net-next. if (ipv4_is_local_multicast(pmc->multiaddr) && !READ_ONCE(net->ipv4.sysctl_igmp_llm_reports))

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix data-races around sysctl_tcp_max_reordering. While reading sysctl_tcp_max_reordering, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: ip: Fix data-races around sysctl_ip_prot_sock. sysctl_ip_prot_sock is accessed concurrently, and there is always a chance of data-race. So, all readers and writers need some basic protection to avoid load/store-tearing.

In the Linux kernel, the following vulnerability has been resolved: ipv4: Fix data-races around sysctl_fib_multipath_hash_fields. While reading sysctl_fib_multipath_hash_fields, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: memcg: protect concurrent access to mem_cgroup_idr Commit 73f576c04b94 ("mm: memcontrol: fix cgroup creation failure after many small jobs") decoupled the memcg IDs from the CSS ID space to fix the cgroup creation failures. It introduced IDR to maintain the memcg ID space. The IDR depends on external synchronization mechanisms for modifications. For the mem_cgroup_idr, the idr_alloc() and idr_replace() happen within css callback and thus are protected through cgroup_mutex from concurrent modifications. However idr_remove() for mem_cgroup_idr was not protected against concurrency and can be run concurrently for different memcgs when they hit their refcnt to zero. Fix that. We have been seeing list_lru based kernel crashes at a low frequency in our fleet for a long time. These crashes were in different part of list_lru code including list_lru_add(), list_lru_del() and reparenting code. Upon further inspection, it looked like for a given object (dentry and inode), the super_block's list_lru didn't have list_lru_one for the memcg of that object. The initial suspicions were either the object is not allocated through kmem_cache_alloc_lru() or somehow memcg_list_lru_alloc() failed to allocate list_lru_one() for a memcg but returned success. No evidence were found for these cases. Looking more deeply, we started seeing situations where valid memcg's id is not present in mem_cgroup_idr and in some cases multiple valid memcgs have same id and mem_cgroup_idr is pointing to one of them. So, the most reasonable explanation is that these situations can happen due to race between multiple idr_remove() calls or race between idr_alloc()/idr_replace() and idr_remove(). These races are causing multiple memcgs to acquire the same ID and then offlining of one of them would cleanup list_lrus on the system for all of them. Later access from other memcgs to the list_lru cause crashes due to missing list_lru_one.

In the Linux kernel, the following vulnerability has been resolved: configfs: fix a race in configfs_{,un}register_subsystem() When configfs_register_subsystem() or configfs_unregister_subsystem() is executing link_group() or unlink_group(), it is possible that two processes add or delete list concurrently. Some unfortunate interleavings of them can cause kernel panic. One of cases is: A --> B --> C --> D A <-- B <-- C <-- D delete list_head *B | delete list_head *C --------------------------------|----------------------------------- configfs_unregister_subsystem | configfs_unregister_subsystem unlink_group | unlink_group unlink_obj | unlink_obj list_del_init | list_del_init __list_del_entry | __list_del_entry __list_del | __list_del // next == C | next->prev = prev | | next->prev = prev prev->next = next | | // prev == B | prev->next = next Fix this by adding mutex when calling link_group() or unlink_group(), but parent configfs_subsystem is NULL when config_item is root. So I create a mutex configfs_subsystem_mutex.

In the Linux kernel, the following vulnerability has been resolved: xsk: Fix race at socket teardown Fix a race in the xsk socket teardown code that can lead to a NULL pointer dereference splat. The current xsk unbind code in xsk_unbind_dev() starts by setting xs->state to XSK_UNBOUND, sets xs->dev to NULL and then waits for any NAPI processing to terminate using synchronize_net(). After that, the release code starts to tear down the socket state and free allocated memory. BUG: kernel NULL pointer dereference, address: 00000000000000c0 PGD 8000000932469067 P4D 8000000932469067 PUD 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 25 PID: 69132 Comm: grpcpp_sync_ser Tainted: G I 5.16.0+ #2 Hardware name: Dell Inc. PowerEdge R730/0599V5, BIOS 1.2.10 03/09/2015 RIP: 0010:__xsk_sendmsg+0x2c/0x690 [...] RSP: 0018:ffffa2348bd13d50 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000040 RCX: ffff8d5fc632d258 RDX: 0000000000400000 RSI: ffffa2348bd13e10 RDI: ffff8d5fc5489800 RBP: ffffa2348bd13db0 R08: 0000000000000000 R09: 00007ffffffff000 R10: 0000000000000000 R11: 0000000000000000 R12: ffff8d5fc5489800 R13: ffff8d5fcb0f5140 R14: ffff8d5fcb0f5140 R15: 0000000000000000 FS: 00007f991cff9400(0000) GS:ffff8d6f1f700000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000000000c0 CR3: 0000000114888005 CR4: 00000000001706e0 Call Trace: <TASK> ? aa_sk_perm+0x43/0x1b0 xsk_sendmsg+0xf0/0x110 sock_sendmsg+0x65/0x70 __sys_sendto+0x113/0x190 ? debug_smp_processor_id+0x17/0x20 ? fpregs_assert_state_consistent+0x23/0x50 ? exit_to_user_mode_prepare+0xa5/0x1d0 __x64_sys_sendto+0x29/0x30 do_syscall_64+0x3b/0xc0 entry_SYSCALL_64_after_hwframe+0x44/0xae There are two problems with the current code. First, setting xs->dev to NULL before waiting for all users to stop using the socket is not correct. The entry to the data plane functions xsk_poll(), xsk_sendmsg(), and xsk_recvmsg() are all guarded by a test that xs->state is in the state XSK_BOUND and if not, it returns right away. But one process might have passed this test but still have not gotten to the point in which it uses xs->dev in the code. In this interim, a second process executing xsk_unbind_dev() might have set xs->dev to NULL which will lead to a crash for the first process. The solution here is just to get rid of this NULL assignment since it is not used anymore. Before commit 42fddcc7c64b ("xsk: use state member for socket synchronization"), xs->dev was the gatekeeper to admit processes into the data plane functions, but it was replaced with the state variable xs->state in the aforementioned commit. The second problem is that synchronize_net() does not wait for any process in xsk_poll(), xsk_sendmsg(), or xsk_recvmsg() to complete, which means that the state they rely on might be cleaned up prematurely. This can happen when the notifier gets called (at driver unload for example) as it uses xsk_unbind_dev(). Solve this by extending the RCU critical region from just the ndo_xsk_wakeup to the whole functions mentioned above, so that both the test of xs->state == XSK_BOUND and the last use of any member of xs is covered by the RCU critical section. This will guarantee that when synchronize_net() completes, there will be no processes left executing xsk_poll(), xsk_sendmsg(), or xsk_recvmsg() and state can be cleaned up safely. Note that we need to drop the RCU lock for the skb xmit path as it uses functions that might sleep. Due to this, we have to retest the xs->state after we grab the mutex that protects the skb xmit code from, among a number of things, an xsk_unbind_dev() being executed from the notifier at the same time.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix data-races around sysctl_tcp_slow_start_after_idle. While reading sysctl_tcp_slow_start_after_idle, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: icmp: Fix data-races around sysctl_icmp_echo_enable_probe. While reading sysctl_icmp_echo_enable_probe, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

roccat_report_event in drivers/hid/hid-roccat.c in the Linux kernel through 5.19.12 has a race condition and resultant use-after-free in certain situations where a report is received while copying a report->value is in progress.

In the Linux kernel, the following vulnerability has been resolved: sysctl: Fix data races in proc_douintvec_minmax(). A sysctl variable is accessed concurrently, and there is always a chance of data-race. So, all readers and writers need some basic protection to avoid load/store-tearing. This patch changes proc_douintvec_minmax() to use READ_ONCE() and WRITE_ONCE() internally to fix data-races on the sysctl side. For now, proc_douintvec_minmax() itself is tolerant to a data-race, but we still need to add annotations on the other subsystem's side.

In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Complete command early within lock A crash was observed while performing NPIV and FW reset, BUG: kernel NULL pointer dereference, address: 000000000000001c #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 1 PREEMPT_RT SMP NOPTI RIP: 0010:dma_direct_unmap_sg+0x51/0x1e0 RSP: 0018:ffffc90026f47b88 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000021 RCX: 0000000000000002 RDX: 0000000000000021 RSI: 0000000000000000 RDI: ffff8881041130d0 RBP: ffff8881041130d0 R08: 0000000000000000 R09: 0000000000000034 R10: ffffc90026f47c48 R11: 0000000000000031 R12: 0000000000000000 R13: 0000000000000000 R14: ffff8881565e4a20 R15: 0000000000000000 FS: 00007f4c69ed3d00(0000) GS:ffff889faac80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000000000001c CR3: 0000000288a50002 CR4: 00000000007706e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> ? __die_body+0x1a/0x60 ? page_fault_oops+0x16f/0x4a0 ? do_user_addr_fault+0x174/0x7f0 ? exc_page_fault+0x69/0x1a0 ? asm_exc_page_fault+0x22/0x30 ? dma_direct_unmap_sg+0x51/0x1e0 ? preempt_count_sub+0x96/0xe0 qla2xxx_qpair_sp_free_dma+0x29f/0x3b0 [qla2xxx] qla2xxx_qpair_sp_compl+0x60/0x80 [qla2xxx] __qla2x00_abort_all_cmds+0xa2/0x450 [qla2xxx] The command completion was done early while aborting the commands in driver unload path but outside lock to avoid the WARN_ON condition of performing dma_free_attr within the lock. However this caused race condition while command completion via multiple paths causing system crash. Hence complete the command early in unload path but within the lock to avoid race condition.

In the Linux kernel, the following vulnerability has been resolved: mm: revert "mm: shmem: fix data-race in shmem_getattr()" Revert d949d1d14fa2 ("mm: shmem: fix data-race in shmem_getattr()") as suggested by Chuck [1]. It is causing deadlocks when accessing tmpfs over NFS. As Hugh commented, "added just to silence a syzbot sanitizer splat: added where there has never been any practical problem".

In the Linux kernel, the following vulnerability has been resolved: ip: Fix data-races around sysctl_ip_fwd_use_pmtu. While reading sysctl_ip_fwd_use_pmtu, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix data-races around sysctl_tcp_min_snd_mss. While reading sysctl_tcp_min_snd_mss, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix data-races around sysctl_tcp_mtu_probing. While reading sysctl_tcp_mtu_probing, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix data-races around sysctl_tcp_fastopen_blackhole_timeout. While reading sysctl_tcp_fastopen_blackhole_timeout, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: drm/virtio: Fix GEM handle creation UAF Userspace can guess the handle value and try to race GEM object creation with handle close, resulting in a use-after-free if we dereference the object after dropping the handle's reference. For that reason, dropping the handle's reference must be done *after* we are done dereferencing the object.

In the Linux kernel, the following vulnerability has been resolved: ipv4: Fix a data-race around sysctl_fib_multipath_use_neigh. While reading sysctl_fib_multipath_use_neigh, it can be changed concurrently. Thus, we need to add READ_ONCE() to its reader.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix a data-race around sysctl_tcp_probe_threshold. While reading sysctl_tcp_probe_threshold, it can be changed concurrently. Thus, we need to add READ_ONCE() to its reader.

In the Linux kernel, the following vulnerability has been resolved: tls: fix race between tx work scheduling and socket close Similarly to previous commit, the submitting thread (recvmsg/sendmsg) may exit as soon as the async crypto handler calls complete(). Reorder scheduling the work before calling complete(). This seems more logical in the first place, as it's the inverse order of what the submitting thread will do.

In the Linux kernel, the following vulnerability has been resolved: USB: gadgetfs: Fix race between mounting and unmounting The syzbot fuzzer and Gerald Lee have identified a use-after-free bug in the gadgetfs driver, involving processes concurrently mounting and unmounting the gadgetfs filesystem. In particular, gadgetfs_fill_super() can race with gadgetfs_kill_sb(), causing the latter to deallocate the_device while the former is using it. The output from KASAN says, in part: BUG: KASAN: use-after-free in instrument_atomic_read_write include/linux/instrumented.h:102 [inline] BUG: KASAN: use-after-free in atomic_fetch_sub_release include/linux/atomic/atomic-instrumented.h:176 [inline] BUG: KASAN: use-after-free in __refcount_sub_and_test include/linux/refcount.h:272 [inline] BUG: KASAN: use-after-free in __refcount_dec_and_test include/linux/refcount.h:315 [inline] BUG: KASAN: use-after-free in refcount_dec_and_test include/linux/refcount.h:333 [inline] BUG: KASAN: use-after-free in put_dev drivers/usb/gadget/legacy/inode.c:159 [inline] BUG: KASAN: use-after-free in gadgetfs_kill_sb+0x33/0x100 drivers/usb/gadget/legacy/inode.c:2086 Write of size 4 at addr ffff8880276d7840 by task syz-executor126/18689 CPU: 0 PID: 18689 Comm: syz-executor126 Not tainted 6.1.0-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022 Call Trace: <TASK> ... atomic_fetch_sub_release include/linux/atomic/atomic-instrumented.h:176 [inline] __refcount_sub_and_test include/linux/refcount.h:272 [inline] __refcount_dec_and_test include/linux/refcount.h:315 [inline] refcount_dec_and_test include/linux/refcount.h:333 [inline] put_dev drivers/usb/gadget/legacy/inode.c:159 [inline] gadgetfs_kill_sb+0x33/0x100 drivers/usb/gadget/legacy/inode.c:2086 deactivate_locked_super+0xa7/0xf0 fs/super.c:332 vfs_get_super fs/super.c:1190 [inline] get_tree_single+0xd0/0x160 fs/super.c:1207 vfs_get_tree+0x88/0x270 fs/super.c:1531 vfs_fsconfig_locked fs/fsopen.c:232 [inline] The simplest solution is to ensure that gadgetfs_fill_super() and gadgetfs_kill_sb() are serialized by making them both acquire a new mutex.

In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Fix memory leak in __qlt_24xx_handle_abts() Commit 8f394da36a36 ("scsi: qla2xxx: Drop TARGET_SCF_LOOKUP_LUN_FROM_TAG") made the __qlt_24xx_handle_abts() function return early if tcm_qla2xxx_find_cmd_by_tag() didn't find a command, but it missed to clean up the allocated memory for the management command.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Add 'replay' NULL check in 'edp_set_replay_allow_active()' In the first if statement, we're checking if 'replay' is NULL. But in the second if statement, we're not checking if 'replay' is NULL again before calling replay->funcs->replay_set_power_opt(). if (replay == NULL && force_static) return false; ... if (link->replay_settings.replay_feature_enabled && replay->funcs->replay_set_power_opt) { replay->funcs->replay_set_power_opt(replay, *power_opts, panel_inst); link->replay_settings.replay_power_opt_active = *power_opts; } If 'replay' is NULL, this will cause a null pointer dereference. Fixes the below found by smatch: drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_edp_panel_control.c:895 edp_set_replay_allow_active() error: we previously assumed 'replay' could be null (see line 887)

In the Linux kernel, the following vulnerability has been resolved: nvmet: fix a possible leak when destroy a ctrl during qp establishment In nvmet_sq_destroy we capture sq->ctrl early and if it is non-NULL we know that a ctrl was allocated (in the admin connect request handler) and we need to release pending AERs, clear ctrl->sqs and sq->ctrl (for nvme-loop primarily), and drop the final reference on the ctrl. However, a small window is possible where nvmet_sq_destroy starts (as a result of the client giving up and disconnecting) concurrently with the nvme admin connect cmd (which may be in an early stage). But *before* kill_and_confirm of sq->ref (i.e. the admin connect managed to get an sq live reference). In this case, sq->ctrl was allocated however after it was captured in a local variable in nvmet_sq_destroy. This prevented the final reference drop on the ctrl. Solve this by re-capturing the sq->ctrl after all inflight request has completed, where for sure sq->ctrl reference is final, and move forward based on that. This issue was observed in an environment with many hosts connecting multiple ctrls simoutanuosly, creating a delay in allocating a ctrl leading up to this race window.

An issue was discovered in the Linux kernel through 5.19.8. drivers/firmware/efi/capsule-loader.c has a race condition with a resultant use-after-free.

In the Linux kernel, the following vulnerability has been resolved: ice: Fix race condition during interface enslave Commit 5dbbbd01cbba83 ("ice: Avoid RTNL lock when re-creating auxiliary device") changes a process of re-creation of aux device so ice_plug_aux_dev() is called from ice_service_task() context. This unfortunately opens a race window that can result in dead-lock when interface has left LAG and immediately enters LAG again. Reproducer: ``` #!/bin/sh ip link add lag0 type bond mode 1 miimon 100 ip link set lag0 for n in {1..10}; do echo Cycle: $n ip link set ens7f0 master lag0 sleep 1 ip link set ens7f0 nomaster done ``` This results in: [20976.208697] Workqueue: ice ice_service_task [ice] [20976.213422] Call Trace: [20976.215871] __schedule+0x2d1/0x830 [20976.219364] schedule+0x35/0xa0 [20976.222510] schedule_preempt_disabled+0xa/0x10 [20976.227043] __mutex_lock.isra.7+0x310/0x420 [20976.235071] enum_all_gids_of_dev_cb+0x1c/0x100 [ib_core] [20976.251215] ib_enum_roce_netdev+0xa4/0xe0 [ib_core] [20976.256192] ib_cache_setup_one+0x33/0xa0 [ib_core] [20976.261079] ib_register_device+0x40d/0x580 [ib_core] [20976.266139] irdma_ib_register_device+0x129/0x250 [irdma] [20976.281409] irdma_probe+0x2c1/0x360 [irdma] [20976.285691] auxiliary_bus_probe+0x45/0x70 [20976.289790] really_probe+0x1f2/0x480 [20976.298509] driver_probe_device+0x49/0xc0 [20976.302609] bus_for_each_drv+0x79/0xc0 [20976.306448] __device_attach+0xdc/0x160 [20976.310286] bus_probe_device+0x9d/0xb0 [20976.314128] device_add+0x43c/0x890 [20976.321287] __auxiliary_device_add+0x43/0x60 [20976.325644] ice_plug_aux_dev+0xb2/0x100 [ice] [20976.330109] ice_service_task+0xd0c/0xed0 [ice] [20976.342591] process_one_work+0x1a7/0x360 [20976.350536] worker_thread+0x30/0x390 [20976.358128] kthread+0x10a/0x120 [20976.365547] ret_from_fork+0x1f/0x40 ... [20976.438030] task:ip state:D stack: 0 pid:213658 ppid:213627 flags:0x00004084 [20976.446469] Call Trace: [20976.448921] __schedule+0x2d1/0x830 [20976.452414] schedule+0x35/0xa0 [20976.455559] schedule_preempt_disabled+0xa/0x10 [20976.460090] __mutex_lock.isra.7+0x310/0x420 [20976.464364] device_del+0x36/0x3c0 [20976.467772] ice_unplug_aux_dev+0x1a/0x40 [ice] [20976.472313] ice_lag_event_handler+0x2a2/0x520 [ice] [20976.477288] notifier_call_chain+0x47/0x70 [20976.481386] __netdev_upper_dev_link+0x18b/0x280 [20976.489845] bond_enslave+0xe05/0x1790 [bonding] [20976.494475] do_setlink+0x336/0xf50 [20976.502517] __rtnl_newlink+0x529/0x8b0 [20976.543441] rtnl_newlink+0x43/0x60 [20976.546934] rtnetlink_rcv_msg+0x2b1/0x360 [20976.559238] netlink_rcv_skb+0x4c/0x120 [20976.563079] netlink_unicast+0x196/0x230 [20976.567005] netlink_sendmsg+0x204/0x3d0 [20976.570930] sock_sendmsg+0x4c/0x50 [20976.574423] ____sys_sendmsg+0x1eb/0x250 [20976.586807] ___sys_sendmsg+0x7c/0xc0 [20976.606353] __sys_sendmsg+0x57/0xa0 [20976.609930] do_syscall_64+0x5b/0x1a0 [20976.613598] entry_SYSCALL_64_after_hwframe+0x65/0xca 1. Command 'ip link ... set nomaster' causes that ice_plug_aux_dev() is called from ice_service_task() context, aux device is created and associated device->lock is taken. 2. Command 'ip link ... set master...' calls ice's notifier under RTNL lock and that notifier calls ice_unplug_aux_dev(). That function tries to take aux device->lock but this is already taken by ice_plug_aux_dev() in step 1 3. Later ice_plug_aux_dev() tries to take RTNL lock but this is already taken in step 2 4. Dead-lock The patch fixes this issue by following changes: - Bit ICE_FLAG_PLUG_AUX_DEV is kept to be set during ice_plug_aux_dev() call in ice_service_task() - The bit is checked in ice_clear_rdma_cap() and only if it is not set then ice_unplug_aux_dev() is called. If it is set (in other words plugging of aux device was requested and ice_plug_aux_dev() is potentially running) then the function only clears the ---truncated---

In the Linux kernel, the following vulnerability has been resolved: vfs: fix race between evice_inodes() and find_inode()&iput() Hi, all Recently I noticed a bug[1] in btrfs, after digged it into and I believe it'a race in vfs. Let's assume there's a inode (ie ino 261) with i_count 1 is called by iput(), and there's a concurrent thread calling generic_shutdown_super(). cpu0: cpu1: iput() // i_count is 1 ->spin_lock(inode) ->dec i_count to 0 ->iput_final() generic_shutdown_super() ->__inode_add_lru() ->evict_inodes() // cause some reason[2] ->if (atomic_read(inode->i_count)) continue; // return before // inode 261 passed the above check // list_lru_add_obj() // and then schedule out ->spin_unlock() // note here: the inode 261 // was still at sb list and hash list, // and I_FREEING|I_WILL_FREE was not been set btrfs_iget() // after some function calls ->find_inode() // found the above inode 261 ->spin_lock(inode) // check I_FREEING|I_WILL_FREE // and passed ->__iget() ->spin_unlock(inode) // schedule back ->spin_lock(inode) // check (I_NEW|I_FREEING|I_WILL_FREE) flags, // passed and set I_FREEING iput() ->spin_unlock(inode) ->spin_lock(inode) ->evict() // dec i_count to 0 ->iput_final() ->spin_unlock() ->evict() Now, we have two threads simultaneously evicting the same inode, which may trigger the BUG(inode->i_state & I_CLEAR) statement both within clear_inode() and iput(). To fix the bug, recheck the inode->i_count after holding i_lock. Because in the most scenarios, the first check is valid, and the overhead of spin_lock() can be reduced. If there is any misunderstanding, please let me know, thanks. [1]: https://lore.kernel.org/linux-btrfs/000000000000eabe1d0619c48986@google.com/ [2]: The reason might be 1. SB_ACTIVE was removed or 2. mapping_shrinkable() return false when I reproduced the bug.

In the Linux kernel, the following vulnerability has been resolved: net/smc: Transitional solution for clcsock race issue We encountered a crash in smc_setsockopt() and it is caused by accessing smc->clcsock after clcsock was released. BUG: kernel NULL pointer dereference, address: 0000000000000020 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 1 PID: 50309 Comm: nginx Kdump: loaded Tainted: G E 5.16.0-rc4+ #53 RIP: 0010:smc_setsockopt+0x59/0x280 [smc] Call Trace: <TASK> __sys_setsockopt+0xfc/0x190 __x64_sys_setsockopt+0x20/0x30 do_syscall_64+0x34/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f16ba83918e </TASK> This patch tries to fix it by holding clcsock_release_lock and checking whether clcsock has already been released before access. In case that a crash of the same reason happens in smc_getsockopt() or smc_switch_to_fallback(), this patch also checkes smc->clcsock in them too. And the caller of smc_switch_to_fallback() will identify whether fallback succeeds according to the return value.

In the Linux kernel, the following vulnerability has been resolved: nvme: fix SRCU protection of nvme_ns_head list Walking the nvme_ns_head siblings list is protected by the head's srcu in nvme_ns_head_submit_bio() but not nvme_mpath_revalidate_paths(). Removing namespaces from the list also fails to synchronize the srcu. Concurrent scan work can therefore cause use-after-frees. Hold the head's srcu lock in nvme_mpath_revalidate_paths() and synchronize with the srcu, not the global RCU, in nvme_ns_remove(). Observed the following panic when making NVMe/RDMA connections with native multipath on the Rocky Linux 8.6 kernel (it seems the upstream kernel has the same race condition). Disassembly shows the faulting instruction is cmp 0x50(%rdx),%rcx; computing capacity != get_capacity(ns->disk). Address 0x50 is dereferenced because ns->disk is NULL. The NULL disk appears to be the result of concurrent scan work freeing the namespace (note the log line in the middle of the panic). [37314.206036] BUG: unable to handle kernel NULL pointer dereference at 0000000000000050 [37314.206036] nvme0n3: detected capacity change from 0 to 11811160064 [37314.299753] PGD 0 P4D 0 [37314.299756] Oops: 0000 [#1] SMP PTI [37314.299759] CPU: 29 PID: 322046 Comm: kworker/u98:3 Kdump: loaded Tainted: G W X --------- - - 4.18.0-372.32.1.el8test86.x86_64 #1 [37314.299762] Hardware name: Dell Inc. PowerEdge R720/0JP31P, BIOS 2.7.0 05/23/2018 [37314.299763] Workqueue: nvme-wq nvme_scan_work [nvme_core] [37314.299783] RIP: 0010:nvme_mpath_revalidate_paths+0x26/0xb0 [nvme_core] [37314.299790] Code: 1f 44 00 00 66 66 66 66 90 55 53 48 8b 5f 50 48 8b 83 c8 c9 00 00 48 8b 13 48 8b 48 50 48 39 d3 74 20 48 8d 42 d0 48 8b 50 20 <48> 3b 4a 50 74 05 f0 80 60 70 ef 48 8b 50 30 48 8d 42 d0 48 39 d3 [37315.058803] RSP: 0018:ffffabe28f913d10 EFLAGS: 00010202 [37315.121316] RAX: ffff927a077da800 RBX: ffff92991dd70000 RCX: 0000000001600000 [37315.206704] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff92991b719800 [37315.292106] RBP: ffff929a6b70c000 R08: 000000010234cd4a R09: c0000000ffff7fff [37315.377501] R10: 0000000000000001 R11: ffffabe28f913a30 R12: 0000000000000000 [37315.462889] R13: ffff92992716600c R14: ffff929964e6e030 R15: ffff92991dd70000 [37315.548286] FS: 0000000000000000(0000) GS:ffff92b87fb80000(0000) knlGS:0000000000000000 [37315.645111] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [37315.713871] CR2: 0000000000000050 CR3: 0000002208810006 CR4: 00000000000606e0 [37315.799267] Call Trace: [37315.828515] nvme_update_ns_info+0x1ac/0x250 [nvme_core] [37315.892075] nvme_validate_or_alloc_ns+0x2ff/0xa00 [nvme_core] [37315.961871] ? __blk_mq_free_request+0x6b/0x90 [37316.015021] nvme_scan_work+0x151/0x240 [nvme_core] [37316.073371] process_one_work+0x1a7/0x360 [37316.121318] ? create_worker+0x1a0/0x1a0 [37316.168227] worker_thread+0x30/0x390 [37316.212024] ? create_worker+0x1a0/0x1a0 [37316.258939] kthread+0x10a/0x120 [37316.297557] ? set_kthread_struct+0x50/0x50 [37316.347590] ret_from_fork+0x35/0x40 [37316.390360] Modules linked in: nvme_rdma nvme_tcp(X) nvme_fabrics nvme_core netconsole iscsi_tcp libiscsi_tcp dm_queue_length dm_service_time nf_conntrack_netlink br_netfilter bridge stp llc overlay nft_chain_nat ipt_MASQUERADE nf_nat xt_addrtype xt_CT nft_counter xt_state xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 xt_comment xt_multiport nft_compat nf_tables libcrc32c nfnetlink dm_multipath tg3 rpcrdma sunrpc rdma_ucm ib_srpt ib_isert iscsi_target_mod target_core_mod ib_iser libiscsi scsi_transport_iscsi ib_umad rdma_cm ib_ipoib iw_cm ib_cm intel_rapl_msr iTCO_wdt iTCO_vendor_support dcdbas intel_rapl_common sb_edac x86_pkg_temp_thermal intel_powerclamp coretemp kvm_intel ipmi_ssif kvm irqbypass crct10dif_pclmul crc32_pclmul mlx5_ib ghash_clmulni_intel ib_uverbs rapl intel_cstate intel_uncore ib_core ipmi_si joydev mei_me pcspkr ipmi_devintf mei lpc_ich wmi ipmi_msghandler acpi_power_meter ex ---truncated---

In the Linux kernel, the following vulnerability has been resolved: sched/fair: Fix fault in reweight_entity Syzbot found a GPF in reweight_entity. This has been bisected to commit 4ef0c5c6b5ba ("kernel/sched: Fix sched_fork() access an invalid sched_task_group") There is a race between sched_post_fork() and setpriority(PRIO_PGRP) within a thread group that causes a null-ptr-deref in reweight_entity() in CFS. The scenario is that the main process spawns number of new threads, which then call setpriority(PRIO_PGRP, 0, -20), wait, and exit. For each of the new threads the copy_process() gets invoked, which adds the new task_struct and calls sched_post_fork() for it. In the above scenario there is a possibility that setpriority(PRIO_PGRP) and set_one_prio() will be called for a thread in the group that is just being created by copy_process(), and for which the sched_post_fork() has not been executed yet. This will trigger a null pointer dereference in reweight_entity(), as it will try to access the run queue pointer, which hasn't been set. Before the mentioned change the cfs_rq pointer for the task has been set in sched_fork(), which is called much earlier in copy_process(), before the new task is added to the thread_group. Now it is done in the sched_post_fork(), which is called after that. To fix the issue the remove the update_load param from the update_load param() function and call reweight_task() only if the task flag doesn't have the TASK_NEW flag set.