In the Linux kernel, the following vulnerability has been resolved: libceph: make free_choose_arg_map() resilient to partial allocation free_choose_arg_map() may dereference a NULL pointer if its caller fails after a partial allocation. For example, in decode_choose_args(), if allocation of arg_map->args fails, execution jumps to the fail label and free_choose_arg_map() is called. Since arg_map->size is updated to a non-zero value before memory allocation, free_choose_arg_map() will iterate over arg_map->args and dereference a NULL pointer. To prevent this potential NULL pointer dereference and make free_choose_arg_map() more resilient, add checks for pointers before iterating.

In the Linux kernel, the following vulnerability has been resolved: libceph: return the handler error from mon_handle_auth_done() Currently any error from ceph_auth_handle_reply_done() is propagated via finish_auth() but isn't returned from mon_handle_auth_done(). This results in higher layers learning that (despite the monitor considering us to be successfully authenticated) something went wrong in the authentication phase and reacting accordingly, but msgr2 still trying to proceed with establishing the session in the background. In the case of secure mode this can trigger a WARN in setup_crypto() and later lead to a NULL pointer dereference inside of prepare_auth_signature().

In the Linux kernel, the following vulnerability has been resolved: crypto: authencesn - reject too-short AAD (assoclen<8) to match ESP/ESN spec authencesn assumes an ESP/ESN-formatted AAD. When assoclen is shorter than the minimum expected length, crypto_authenc_esn_decrypt() can advance past the end of the destination scatterlist and trigger a NULL pointer dereference in scatterwalk_map_and_copy(), leading to a kernel panic (DoS). Add a minimum AAD length check to fail fast on invalid inputs.

In the Linux kernel, the following vulnerability has been resolved: drm/msm/dp: populate connector of struct dp_panel DP CTS test case 4.2.2.6 has valid edid with bad checksum on purpose and expect DP source return correct checksum. During drm edid read, correct edid checksum is calculated and stored at connector::real_edid_checksum. The problem is struct dp_panel::connector never be assigned, instead the connector is stored in struct msm_dp::connector. When we run compliance testing test case 4.2.2.6 dp_panel_handle_sink_request() won't have a valid edid set in struct dp_panel::edid so we'll try to use the connectors real_edid_checksum and hit a NULL pointer dereference error because the connector pointer is never assigned. Changes in V2: -- populate panel connector at msm_dp_modeset_init() instead of at dp_panel_read_sink_caps() Changes in V3: -- remove unhelpful kernel crash trace commit text -- remove renaming dp_display parameter to dp Changes in V4: -- add more details to commit text Changes in v10: -- group into one series Changes in v11: -- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read Signee-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>

In the Linux kernel, the following vulnerability has been resolved: drm/vmwgfx: Fix KMS with 3D on HW version 10 HW version 10 does not have GB Surfaces so there is no backing buffer for surface backed FBs. This would result in a nullptr dereference and crash the driver causing a black screen.

In the Linux kernel, the following vulnerability has been resolved: net: dsa: fix panic on shutdown if multi-chip tree failed to probe DSA probing is atypical because a tree of devices must probe all at once, so out of N switches which call dsa_tree_setup_routing_table() during probe, for (N - 1) of them, "complete" will return false and they will exit probing early. The Nth switch will set up the whole tree on their behalf. The implication is that for (N - 1) switches, the driver binds to the device successfully, without doing anything. When the driver is bound, the ->shutdown() method may run. But if the Nth switch has failed to initialize the tree, there is nothing to do for the (N - 1) driver instances, since the slave devices have not been created, etc. Moreover, dsa_switch_shutdown() expects that the calling @ds has been in fact initialized, so it jumps at dereferencing the various data structures, which is incorrect. Avoid the ensuing NULL pointer dereferences by simply checking whether the Nth switch has previously set "ds->setup = true" for the switch which is currently shutting down. The entire setup is serialized under dsa2_mutex which we already hold.

In the Linux kernel, the following vulnerability has been resolved: rose: Fix NULL pointer dereference in rose_send_frame() The syzkaller reported an issue: KASAN: null-ptr-deref in range [0x0000000000000380-0x0000000000000387] CPU: 0 PID: 4069 Comm: kworker/0:15 Not tainted 6.0.0-syzkaller-02734-g0326074ff465 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/22/2022 Workqueue: rcu_gp srcu_invoke_callbacks RIP: 0010:rose_send_frame+0x1dd/0x2f0 net/rose/rose_link.c:101 Call Trace: <IRQ> rose_transmit_clear_request+0x1d5/0x290 net/rose/rose_link.c:255 rose_rx_call_request+0x4c0/0x1bc0 net/rose/af_rose.c:1009 rose_loopback_timer+0x19e/0x590 net/rose/rose_loopback.c:111 call_timer_fn+0x1a0/0x6b0 kernel/time/timer.c:1474 expire_timers kernel/time/timer.c:1519 [inline] __run_timers.part.0+0x674/0xa80 kernel/time/timer.c:1790 __run_timers kernel/time/timer.c:1768 [inline] run_timer_softirq+0xb3/0x1d0 kernel/time/timer.c:1803 __do_softirq+0x1d0/0x9c8 kernel/softirq.c:571 [...] </IRQ> It triggers NULL pointer dereference when 'neigh->dev->dev_addr' is called in the rose_send_frame(). It's the first occurrence of the `neigh` is in rose_loopback_timer() as `rose_loopback_neigh', and the 'dev' in 'rose_loopback_neigh' is initialized sa nullptr. It had been fixed by commit 3b3fd068c56e3fbea30090859216a368398e39bf ("rose: Fix Null pointer dereference in rose_send_frame()") ever. But it's introduced by commit 3c53cd65dece47dd1f9d3a809f32e59d1d87b2b8 ("rose: check NULL rose_loopback_neigh->loopback") again. We fix it by add NULL check in rose_transmit_clear_request(). When the 'dev' in 'neigh' is NULL, we don't reply the request and just clear it. syzkaller don't provide repro, and I provide a syz repro like: r0 = syz_init_net_socket$bt_sco(0x1f, 0x5, 0x2) ioctl$sock_inet_SIOCSIFFLAGS(r0, 0x8914, &(0x7f0000000180)={'rose0\x00', 0x201}) r1 = syz_init_net_socket$rose(0xb, 0x5, 0x0) bind$rose(r1, &(0x7f00000000c0)=@full={0xb, @dev, @null, 0x0, [@null, @null, @netrom, @netrom, @default, @null]}, 0x40) connect$rose(r1, &(0x7f0000000240)=@short={0xb, @dev={0xbb, 0xbb, 0xbb, 0x1, 0x0}, @remote={0xcc, 0xcc, 0xcc, 0xcc, 0xcc, 0xcc, 0x1}, 0x1, @netrom={0xbb, 0xbb, 0xbb, 0xbb, 0xbb, 0x0, 0x0}}, 0x1c)

In the Linux kernel, the following vulnerability has been resolved: net: marvell: prestera: fix NULL dereference on devlink_alloc() failure devlink_alloc() may return NULL on allocation failure, but prestera_devlink_alloc() unconditionally calls devlink_priv() on the returned pointer. This leads to a NULL pointer dereference if devlink allocation fails. Add a check for a NULL devlink pointer and return NULL early to avoid the crash.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/pm: fix the null pointer while the smu is disabled It needs to check if the pp_funcs is initialized while release the context, otherwise it will trigger null pointer panic while the software smu is not enabled. [ 1109.404555] BUG: kernel NULL pointer dereference, address: 0000000000000078 [ 1109.404609] #PF: supervisor read access in kernel mode [ 1109.404638] #PF: error_code(0x0000) - not-present page [ 1109.404657] PGD 0 P4D 0 [ 1109.404672] Oops: 0000 [#1] PREEMPT SMP NOPTI [ 1109.404701] CPU: 7 PID: 9150 Comm: amdgpu_test Tainted: G OEL 5.16.0-custom #1 [ 1109.404732] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 1109.404765] RIP: 0010:amdgpu_dpm_force_performance_level+0x1d/0x170 [amdgpu] [ 1109.405109] Code: 5d c3 44 8b a3 f0 80 00 00 eb e5 66 90 0f 1f 44 00 00 55 48 89 e5 41 57 41 56 41 55 41 54 53 48 83 ec 08 4c 8b b7 f0 7d 00 00 <49> 83 7e 78 00 0f 84 f2 00 00 00 80 bf 87 80 00 00 00 48 89 fb 0f [ 1109.405176] RSP: 0018:ffffaf3083ad7c20 EFLAGS: 00010282 [ 1109.405203] RAX: 0000000000000000 RBX: ffff9796b1c14600 RCX: 0000000002862007 [ 1109.405229] RDX: ffff97968591c8c0 RSI: 0000000000000001 RDI: ffff9796a3700000 [ 1109.405260] RBP: ffffaf3083ad7c50 R08: ffffffff9897de00 R09: ffff979688d9db60 [ 1109.405286] R10: 0000000000000000 R11: ffff979688d9db90 R12: 0000000000000001 [ 1109.405316] R13: ffff9796a3700000 R14: 0000000000000000 R15: ffff9796a3708fc0 [ 1109.405345] FS: 00007ff055cff180(0000) GS:ffff9796bfdc0000(0000) knlGS:0000000000000000 [ 1109.405378] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1109.405400] CR2: 0000000000000078 CR3: 000000000a394000 CR4: 00000000000506e0 [ 1109.405434] Call Trace: [ 1109.405445] <TASK> [ 1109.405456] ? delete_object_full+0x1d/0x20 [ 1109.405480] amdgpu_ctx_set_stable_pstate+0x7c/0xa0 [amdgpu] [ 1109.405698] amdgpu_ctx_fini.part.0+0xcb/0x100 [amdgpu] [ 1109.405911] amdgpu_ctx_do_release+0x71/0x80 [amdgpu] [ 1109.406121] amdgpu_ctx_ioctl+0x52d/0x550 [amdgpu] [ 1109.406327] ? _raw_spin_unlock+0x1a/0x30 [ 1109.406354] ? drm_gem_handle_delete+0x81/0xb0 [drm] [ 1109.406400] ? amdgpu_ctx_get_entity+0x2c0/0x2c0 [amdgpu] [ 1109.406609] drm_ioctl_kernel+0xb6/0x140 [drm]

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: fix general-protection-fault in ieee80211_subif_start_xmit() When device is running and the interface status is changed, the gpf issue is triggered. The problem triggering process is as follows: Thread A: Thread B ieee80211_runtime_change_iftype() process_one_work() ... ... ieee80211_do_stop() ... ... ... sdata->bss = NULL ... ... ieee80211_subif_start_xmit() ieee80211_multicast_to_unicast //!sdata->bss->multicast_to_unicast cause gpf issue When the interface status is changed, the sending queue continues to send packets. After the bss is set to NULL, the bss is accessed. As a result, this causes a general-protection-fault issue. The following is the stack information: general protection fault, probably for non-canonical address 0xdffffc000000002f: 0000 [#1] PREEMPT SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000178-0x000000000000017f] Workqueue: mld mld_ifc_work RIP: 0010:ieee80211_subif_start_xmit+0x25b/0x1310 Call Trace: <TASK> dev_hard_start_xmit+0x1be/0x990 __dev_queue_xmit+0x2c9a/0x3b60 ip6_finish_output2+0xf92/0x1520 ip6_finish_output+0x6af/0x11e0 ip6_output+0x1ed/0x540 mld_sendpack+0xa09/0xe70 mld_ifc_work+0x71c/0xdb0 process_one_work+0x9bf/0x1710 worker_thread+0x665/0x1080 kthread+0x2e4/0x3a0 ret_from_fork+0x1f/0x30 </TASK>

In the Linux kernel, the following vulnerability has been resolved: net/sched: sch_qfq: Fix NULL deref when deactivating inactive aggregate in qfq_reset `qfq_class->leaf_qdisc->q.qlen > 0` does not imply that the class itself is active. Two qfq_class objects may point to the same leaf_qdisc. This happens when: 1. one QFQ qdisc is attached to the dev as the root qdisc, and 2. another QFQ qdisc is temporarily referenced (e.g., via qdisc_get() / qdisc_put()) and is pending to be destroyed, as in function tc_new_tfilter. When packets are enqueued through the root QFQ qdisc, the shared leaf_qdisc->q.qlen increases. At the same time, the second QFQ qdisc triggers qdisc_put and qdisc_destroy: the qdisc enters qfq_reset() with its own q->q.qlen == 0, but its class's leaf qdisc->q.qlen > 0. Therefore, the qfq_reset would wrongly deactivate an inactive aggregate and trigger a null-deref in qfq_deactivate_agg: [ 0.903172] BUG: kernel NULL pointer dereference, address: 0000000000000000 [ 0.903571] #PF: supervisor write access in kernel mode [ 0.903860] #PF: error_code(0x0002) - not-present page [ 0.904177] PGD 10299b067 P4D 10299b067 PUD 10299c067 PMD 0 [ 0.904502] Oops: Oops: 0002 [#1] SMP NOPTI [ 0.904737] CPU: 0 UID: 0 PID: 135 Comm: exploit Not tainted 6.19.0-rc3+ #2 NONE [ 0.905157] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.17.0-0-gb52ca86e094d-prebuilt.qemu.org 04/01/2014 [ 0.905754] RIP: 0010:qfq_deactivate_agg (include/linux/list.h:992 (discriminator 2) include/linux/list.h:1006 (discriminator 2) net/sched/sch_qfq.c:1367 (discriminator 2) net/sched/sch_qfq.c:1393 (discriminator 2)) [ 0.906046] Code: 0f 84 4d 01 00 00 48 89 70 18 8b 4b 10 48 c7 c2 ff ff ff ff 48 8b 78 08 48 d3 e2 48 21 f2 48 2b 13 48 8b 30 48 d3 ea 8b 4b 18 0 Code starting with the faulting instruction =========================================== 0: 0f 84 4d 01 00 00 je 0x153 6: 48 89 70 18 mov %rsi,0x18(%rax) a: 8b 4b 10 mov 0x10(%rbx),%ecx d: 48 c7 c2 ff ff ff ff mov $0xffffffffffffffff,%rdx 14: 48 8b 78 08 mov 0x8(%rax),%rdi 18: 48 d3 e2 shl %cl,%rdx 1b: 48 21 f2 and %rsi,%rdx 1e: 48 2b 13 sub (%rbx),%rdx 21: 48 8b 30 mov (%rax),%rsi 24: 48 d3 ea shr %cl,%rdx 27: 8b 4b 18 mov 0x18(%rbx),%ecx ... [ 0.907095] RSP: 0018:ffffc900004a39a0 EFLAGS: 00010246 [ 0.907368] RAX: ffff8881043a0880 RBX: ffff888102953340 RCX: 0000000000000000 [ 0.907723] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 [ 0.908100] RBP: ffff888102952180 R08: 0000000000000000 R09: 0000000000000000 [ 0.908451] R10: ffff8881043a0000 R11: 0000000000000000 R12: ffff888102952000 [ 0.908804] R13: ffff888102952180 R14: ffff8881043a0ad8 R15: ffff8881043a0880 [ 0.909179] FS: 000000002a1a0380(0000) GS:ffff888196d8d000(0000) knlGS:0000000000000000 [ 0.909572] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 0.909857] CR2: 0000000000000000 CR3: 0000000102993002 CR4: 0000000000772ef0 [ 0.910247] PKRU: 55555554 [ 0.910391] Call Trace: [ 0.910527] <TASK> [ 0.910638] qfq_reset_qdisc (net/sched/sch_qfq.c:357 net/sched/sch_qfq.c:1485) [ 0.910826] qdisc_reset (include/linux/skbuff.h:2195 include/linux/skbuff.h:2501 include/linux/skbuff.h:3424 include/linux/skbuff.h:3430 net/sched/sch_generic.c:1036) [ 0.911040] __qdisc_destroy (net/sched/sch_generic.c:1076) [ 0.911236] tc_new_tfilter (net/sched/cls_api.c:2447) [ 0.911447] rtnetlink_rcv_msg (net/core/rtnetlink.c:6958) [ 0.911663] ? __pfx_rtnetlink_rcv_msg (net/core/rtnetlink.c:6861) [ 0.911894] netlink_rcv_skb (net/netlink/af_netlink.c:2550) [ 0.912100] netlink_unicast (net/netlink/af_netlink.c:1319 net/netlink/af_netlink.c:1344) [ 0.912296] ? __alloc_skb (net/core/skbuff.c:706) [ 0.912484] netlink_sendmsg (net/netlink/af ---truncated---

In the Linux kernel, the following vulnerability has been resolved: ata: libata-transport: fix error handling in ata_tport_add() In ata_tport_add(), the return value of transport_add_device() is not checked. As a result, it causes null-ptr-deref while removing the module, because transport_remove_device() is called to remove the device that was not added. Unable to handle kernel NULL pointer dereference at virtual address 00000000000000d0 CPU: 12 PID: 13605 Comm: rmmod Kdump: loaded Tainted: G W 6.1.0-rc3+ #8 pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : device_del+0x48/0x39c lr : device_del+0x44/0x39c Call trace: device_del+0x48/0x39c attribute_container_class_device_del+0x28/0x40 transport_remove_classdev+0x60/0x7c attribute_container_device_trigger+0x118/0x120 transport_remove_device+0x20/0x30 ata_tport_delete+0x34/0x60 [libata] ata_port_detach+0x148/0x1b0 [libata] ata_pci_remove_one+0x50/0x80 [libata] ahci_remove_one+0x4c/0x8c [ahci] Fix this by checking and handling return value of transport_add_device() in ata_tport_add().

In the Linux kernel, the following vulnerability has been resolved: xen/privcmd: fix error exit of privcmd_ioctl_dm_op() The error exit of privcmd_ioctl_dm_op() is calling unlock_pages() potentially with pages being NULL, leading to a NULL dereference. Additionally lock_pages() doesn't check for pin_user_pages_fast() having been completely successful, resulting in potentially not locking all pages into memory. This could result in sporadic failures when using the related memory in user mode. Fix all of that by calling unlock_pages() always with the real number of pinned pages, which will be zero in case pages being NULL, and by checking the number of pages pinned by pin_user_pages_fast() matching the expected number of pages.

In the Linux kernel, the following vulnerability has been resolved: drm/msm/hdmi: check return value after calling platform_get_resource_byname() It will cause null-ptr-deref if platform_get_resource_byname() returns NULL, we need check the return value. Patchwork: https://patchwork.freedesktop.org/patch/482992/

In the Linux kernel, the following vulnerability has been resolved: HID: nintendo: fix rumble worker null pointer deref We can dereference a null pointer trying to queue work to a destroyed workqueue. If the device is disconnected, nintendo_hid_remove is called, in which the rumble_queue is destroyed. Avoid using that queue to defer rumble work once the controller state is set to JOYCON_CTLR_STATE_REMOVED. This eliminates the null pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: rtc: pl031: fix rtc features null pointer dereference When there is no interrupt line, rtc alarm feature is disabled. The clearing of the alarm feature bit was being done prior to allocations of ldata->rtc device, resulting in a null pointer dereference. Clear RTC_FEATURE_ALARM after the rtc device is allocated.

In the Linux kernel, the following vulnerability has been resolved: drm/ttm: Fix dummy res NULL ptr deref bug Check the bo->resource value before accessing the resource mem_type. v2: Fix commit description unwrapped warning <log snip> [ 40.191227][ T184] general protection fault, probably for non-canonical address 0xdffffc0000000002: 0000 [#1] SMP KASAN PTI [ 40.192995][ T184] KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017] [ 40.194411][ T184] CPU: 1 PID: 184 Comm: systemd-udevd Not tainted 5.19.0-rc4-00721-gb297c22b7070 #1 [ 40.196063][ T184] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-debian-1.16.0-4 04/01/2014 [ 40.199605][ T184] RIP: 0010:ttm_bo_validate+0x1b3/0x240 [ttm] [ 40.200754][ T184] Code: e8 72 c5 ff ff 83 f8 b8 74 d4 85 c0 75 54 49 8b 9e 58 01 00 00 48 b8 00 00 00 00 00 fc ff df 48 8d 7b 10 48 89 fa 48 c1 ea 03 <0f> b6 04 02 84 c0 74 04 3c 03 7e 44 8b 53 10 31 c0 85 d2 0f 85 58 [ 40.203685][ T184] RSP: 0018:ffffc900006df0c8 EFLAGS: 00010202 [ 40.204630][ T184] RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 1ffff1102f4bb71b [ 40.205864][ T184] RDX: 0000000000000002 RSI: ffffc900006df208 RDI: 0000000000000010 [ 40.207102][ T184] RBP: 1ffff920000dbe1a R08: ffffc900006df208 R09: 0000000000000000 [ 40.208394][ T184] R10: ffff88817a5f0000 R11: 0000000000000001 R12: ffffc900006df110 [ 40.209692][ T184] R13: ffffc900006df0f0 R14: ffff88817a5db800 R15: ffffc900006df208 [ 40.210862][ T184] FS: 00007f6b1d16e8c0(0000) GS:ffff88839d700000(0000) knlGS:0000000000000000 [ 40.212250][ T184] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 40.213275][ T184] CR2: 000055a1001d4ff0 CR3: 00000001700f4000 CR4: 00000000000006e0 [ 40.214469][ T184] Call Trace: [ 40.214974][ T184] <TASK> [ 40.215438][ T184] ? ttm_bo_bounce_temp_buffer+0x140/0x140 [ttm] [ 40.216572][ T184] ? mutex_spin_on_owner+0x240/0x240 [ 40.217456][ T184] ? drm_vma_offset_add+0xaa/0x100 [drm] [ 40.218457][ T184] ttm_bo_init_reserved+0x3d6/0x540 [ttm] [ 40.219410][ T184] ? shmem_get_inode+0x744/0x980 [ 40.220231][ T184] ttm_bo_init_validate+0xb1/0x200 [ttm] [ 40.221172][ T184] ? bo_driver_evict_flags+0x340/0x340 [drm_vram_helper] [ 40.222530][ T184] ? ttm_bo_init_reserved+0x540/0x540 [ttm] [ 40.223643][ T184] ? __do_sys_finit_module+0x11a/0x1c0 [ 40.224654][ T184] ? __shmem_file_setup+0x102/0x280 [ 40.234764][ T184] drm_gem_vram_create+0x305/0x480 [drm_vram_helper] [ 40.235766][ T184] ? bo_driver_evict_flags+0x340/0x340 [drm_vram_helper] [ 40.236846][ T184] ? __kasan_slab_free+0x108/0x180 [ 40.237650][ T184] drm_gem_vram_fill_create_dumb+0x134/0x340 [drm_vram_helper] [ 40.238864][ T184] ? local_pci_probe+0xdf/0x180 [ 40.239674][ T184] ? drmm_vram_helper_init+0x400/0x400 [drm_vram_helper] [ 40.240826][ T184] drm_client_framebuffer_create+0x19c/0x400 [drm] [ 40.241955][ T184] ? drm_client_buffer_delete+0x200/0x200 [drm] [ 40.243001][ T184] ? drm_client_pick_crtcs+0x554/0xb80 [drm] [ 40.244030][ T184] drm_fb_helper_generic_probe+0x23f/0x940 [drm_kms_helper] [ 40.245226][ T184] ? __cond_resched+0x1c/0xc0 [ 40.245987][ T184] ? drm_fb_helper_memory_range_to_clip+0x180/0x180 [drm_kms_helper] [ 40.247316][ T184] ? mutex_unlock+0x80/0x100 [ 40.248005][ T184] ? __mutex_unlock_slowpath+0x2c0/0x2c0 [ 40.249083][ T184] drm_fb_helper_single_fb_probe+0x907/0xf00 [drm_kms_helper] [ 40.250314][ T184] ? drm_fb_helper_check_var+0x1180/0x1180 [drm_kms_helper] [ 40.251540][ T184] ? __cond_resched+0x1c/0xc0 [ 40.252321][ T184] ? mutex_lock+0x9f/0x100 [ 40.253062][ T184] __drm_fb_helper_initial_config_and_unlock+0xb9/0x2c0 [drm_kms_helper] [ 40.254394][ T184] drm_fbdev_client_hotplug+0x56f/0x840 [drm_kms_helper] [ 40.255477][ T184] drm_fbdev_generic_setup+0x165/0x3c0 [drm_kms_helper] [ 40.256607][ T184] bochs_pci_probe+0x6b7/0x900 [bochs] [ ---truncated---

In the Linux kernel, the following vulnerability has been resolved: ice: xsk: prohibit usage of non-balanced queue id Fix the following scenario: 1. ethtool -L $IFACE rx 8 tx 96 2. xdpsock -q 10 -t -z Above refers to a case where user would like to attach XSK socket in txonly mode at a queue id that does not have a corresponding Rx queue. At this moment ice's XSK logic is tightly bound to act on a "queue pair", e.g. both Tx and Rx queues at a given queue id are disabled/enabled and both of them will get XSK pool assigned, which is broken for the presented queue configuration. This results in the splat included at the bottom, which is basically an OOB access to Rx ring array. To fix this, allow using the ids only in scope of "combined" queues reported by ethtool. However, logic should be rewritten to allow such configurations later on, which would end up as a complete rewrite of the control path, so let us go with this temporary fix. [420160.558008] BUG: kernel NULL pointer dereference, address: 0000000000000082 [420160.566359] #PF: supervisor read access in kernel mode [420160.572657] #PF: error_code(0x0000) - not-present page [420160.579002] PGD 0 P4D 0 [420160.582756] Oops: 0000 [#1] PREEMPT SMP NOPTI [420160.588396] CPU: 10 PID: 21232 Comm: xdpsock Tainted: G OE 5.19.0-rc7+ #10 [420160.597893] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0008.031920191559 03/19/2019 [420160.609894] RIP: 0010:ice_xsk_pool_setup+0x44/0x7d0 [ice] [420160.616968] Code: f3 48 83 ec 40 48 8b 4f 20 48 8b 3f 65 48 8b 04 25 28 00 00 00 48 89 44 24 38 31 c0 48 8d 04 ed 00 00 00 00 48 01 c1 48 8b 11 <0f> b7 92 82 00 00 00 48 85 d2 0f 84 2d 75 00 00 48 8d 72 ff 48 85 [420160.639421] RSP: 0018:ffffc9002d2afd48 EFLAGS: 00010282 [420160.646650] RAX: 0000000000000050 RBX: ffff88811d8bdd00 RCX: ffff888112c14ff8 [420160.655893] RDX: 0000000000000000 RSI: ffff88811d8bdd00 RDI: ffff888109861000 [420160.665166] RBP: 000000000000000a R08: 000000000000000a R09: 0000000000000000 [420160.674493] R10: 000000000000889f R11: 0000000000000000 R12: 000000000000000a [420160.683833] R13: 000000000000000a R14: 0000000000000000 R15: ffff888117611828 [420160.693211] FS: 00007fa869fc1f80(0000) GS:ffff8897e0880000(0000) knlGS:0000000000000000 [420160.703645] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [420160.711783] CR2: 0000000000000082 CR3: 00000001d076c001 CR4: 00000000007706e0 [420160.721399] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [420160.731045] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [420160.740707] PKRU: 55555554 [420160.745960] Call Trace: [420160.750962] <TASK> [420160.755597] ? kmalloc_large_node+0x79/0x90 [420160.762703] ? __kmalloc_node+0x3f5/0x4b0 [420160.769341] xp_assign_dev+0xfd/0x210 [420160.775661] ? shmem_file_read_iter+0x29a/0x420 [420160.782896] xsk_bind+0x152/0x490 [420160.788943] __sys_bind+0xd0/0x100 [420160.795097] ? exit_to_user_mode_prepare+0x20/0x120 [420160.802801] __x64_sys_bind+0x16/0x20 [420160.809298] do_syscall_64+0x38/0x90 [420160.815741] entry_SYSCALL_64_after_hwframe+0x63/0xcd [420160.823731] RIP: 0033:0x7fa86a0dd2fb [420160.830264] Code: c3 66 0f 1f 44 00 00 48 8b 15 69 8b 0c 00 f7 d8 64 89 02 b8 ff ff ff ff eb bc 0f 1f 44 00 00 f3 0f 1e fa b8 31 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 3d 8b 0c 00 f7 d8 64 89 01 48 [420160.855410] RSP: 002b:00007ffc1146f618 EFLAGS: 00000246 ORIG_RAX: 0000000000000031 [420160.866366] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fa86a0dd2fb [420160.876957] RDX: 0000000000000010 RSI: 00007ffc1146f680 RDI: 0000000000000003 [420160.887604] RBP: 000055d7113a0520 R08: 00007fa868fb8000 R09: 0000000080000000 [420160.898293] R10: 0000000000008001 R11: 0000000000000246 R12: 000055d7113a04e0 [420160.909038] R13: 000055d7113a0320 R14: 000000000000000a R15: 0000000000000000 [420160.919817] </TASK> [420160.925659] Modules linked in: ice(OE) af_packet binfmt_misc ---truncated---

In the Linux kernel, the following vulnerability has been resolved: xfrm: policy: fix metadata dst->dev xmit null pointer dereference When we try to transmit an skb with metadata_dst attached (i.e. dst->dev == NULL) through xfrm interface we can hit a null pointer dereference[1] in xfrmi_xmit2() -> xfrm_lookup_with_ifid() due to the check for a loopback skb device when there's no policy which dereferences dst->dev unconditionally. Not having dst->dev can be interepreted as it not being a loopback device, so just add a check for a null dst_orig->dev. With this fix xfrm interface's Tx error counters go up as usual. [1] net-next calltrace captured via netconsole: BUG: kernel NULL pointer dereference, address: 00000000000000c0 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP CPU: 1 PID: 7231 Comm: ping Kdump: loaded Not tainted 5.19.0+ #24 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.0-1.fc36 04/01/2014 RIP: 0010:xfrm_lookup_with_ifid+0x5eb/0xa60 Code: 8d 74 24 38 e8 26 a4 37 00 48 89 c1 e9 12 fc ff ff 49 63 ed 41 83 fd be 0f 85 be 01 00 00 41 be ff ff ff ff 45 31 ed 48 8b 03 <f6> 80 c0 00 00 00 08 75 0f 41 80 bc 24 19 0d 00 00 01 0f 84 1e 02 RSP: 0018:ffffb0db82c679f0 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffffd0db7fcad430 RCX: ffffb0db82c67a10 RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffb0db82c67a80 RBP: ffffb0db82c67a80 R08: ffffb0db82c67a14 R09: 0000000000000000 R10: 0000000000000000 R11: ffff8fa449667dc8 R12: ffffffff966db880 R13: 0000000000000000 R14: 00000000ffffffff R15: 0000000000000000 FS: 00007ff35c83f000(0000) GS:ffff8fa478480000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000000000c0 CR3: 000000001ebb7000 CR4: 0000000000350ee0 Call Trace: <TASK> xfrmi_xmit+0xde/0x460 ? tcf_bpf_act+0x13d/0x2a0 dev_hard_start_xmit+0x72/0x1e0 __dev_queue_xmit+0x251/0xd30 ip_finish_output2+0x140/0x550 ip_push_pending_frames+0x56/0x80 raw_sendmsg+0x663/0x10a0 ? try_charge_memcg+0x3fd/0x7a0 ? __mod_memcg_lruvec_state+0x93/0x110 ? sock_sendmsg+0x30/0x40 sock_sendmsg+0x30/0x40 __sys_sendto+0xeb/0x130 ? handle_mm_fault+0xae/0x280 ? do_user_addr_fault+0x1e7/0x680 ? kvm_read_and_reset_apf_flags+0x3b/0x50 __x64_sys_sendto+0x20/0x30 do_syscall_64+0x34/0x80 entry_SYSCALL_64_after_hwframe+0x46/0xb0 RIP: 0033:0x7ff35cac1366 Code: eb 0b 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 11 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 72 c3 90 55 48 83 ec 30 44 89 4c 24 2c 4c 89 RSP: 002b:00007fff738e4028 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 00007fff738e57b0 RCX: 00007ff35cac1366 RDX: 0000000000000040 RSI: 0000557164e4b450 RDI: 0000000000000003 RBP: 0000557164e4b450 R08: 00007fff738e7a2c R09: 0000000000000010 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000040 R13: 00007fff738e5770 R14: 00007fff738e4030 R15: 0000001d00000001 </TASK> Modules linked in: netconsole veth br_netfilter bridge bonding virtio_net [last unloaded: netconsole] CR2: 00000000000000c0

In the Linux kernel, the following vulnerability has been resolved: drm/amdkfd: Fix NULL pointer dereference in svm_migrate_to_ram() ./drivers/gpu/drm/amd/amdkfd/kfd_migrate.c:985:58-62: ERROR: p is NULL but dereferenced.

In the Linux kernel, the following vulnerability has been resolved: pinctrl: renesas: core: Fix possible null-ptr-deref in sh_pfc_map_resources() It will cause null-ptr-deref when using 'res', if platform_get_resource() returns NULL, so move using 'res' after devm_ioremap_resource() that will check it to avoid null-ptr-deref. And use devm_platform_get_and_ioremap_resource() to simplify code.

In the Linux kernel, the following vulnerability has been resolved: tty: n_gsm: add sanity check for gsm->receive in gsm_receive_buf() A null pointer dereference can happen when attempting to access the "gsm->receive()" function in gsmld_receive_buf(). Currently, the code assumes that gsm->recieve is only called after MUX activation. Since the gsmld_receive_buf() function can be accessed without the need to initialize the MUX, the gsm->receive() function will not be set and a NULL pointer dereference will occur. Fix this by avoiding the call to "gsm->receive()" in case the function is not initialized by adding a sanity check. Call Trace: <TASK> gsmld_receive_buf+0x1c2/0x2f0 drivers/tty/n_gsm.c:2861 tiocsti drivers/tty/tty_io.c:2293 [inline] tty_ioctl+0xa75/0x15d0 drivers/tty/tty_io.c:2692 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:870 [inline] __se_sys_ioctl fs/ioctl.c:856 [inline] __x64_sys_ioctl+0x193/0x200 fs/ioctl.c:856 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd

In the Linux kernel, the following vulnerability has been resolved: drm/msm/mdp5: Return error code in mdp5_mixer_release when deadlock is detected There is a possibility for mdp5_get_global_state to return -EDEADLK when acquiring the modeset lock, but currently global_state in mdp5_mixer_release doesn't check for if an error is returned. To avoid a NULL dereference error, let's have mdp5_mixer_release check if an error is returned and propagate that error. Patchwork: https://patchwork.freedesktop.org/patch/485181/

In the Linux kernel, the following vulnerability has been resolved: md: Don't set mddev private to NULL in raid0 pers->free In normal stop process, it does like this: do_md_stop | __md_stop (pers->free(); mddev->private=NULL) | md_free (free mddev) __md_stop sets mddev->private to NULL after pers->free. The raid device will be stopped and mddev memory is free. But in reshape, it doesn't free the mddev and mddev will still be used in new raid. In reshape, it first sets mddev->private to new_pers and then runs old_pers->free(). Now raid0 sets mddev->private to NULL in raid0_free. The new raid can't work anymore. It will panic when dereference mddev->private because of NULL pointer dereference. It can panic like this: [63010.814972] kernel BUG at drivers/md/raid10.c:928! [63010.819778] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI [63010.825011] CPU: 3 PID: 44437 Comm: md0_resync Kdump: loaded Not tainted 5.14.0-86.el9.x86_64 #1 [63010.833789] Hardware name: Dell Inc. PowerEdge R6415/07YXFK, BIOS 1.15.0 09/11/2020 [63010.841440] RIP: 0010:raise_barrier+0x161/0x170 [raid10] [63010.865508] RSP: 0018:ffffc312408bbc10 EFLAGS: 00010246 [63010.870734] RAX: 0000000000000000 RBX: ffffa00bf7d39800 RCX: 0000000000000000 [63010.877866] RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffffa00bf7d39800 [63010.884999] RBP: 0000000000000000 R08: fffffa4945e74400 R09: 0000000000000000 [63010.892132] R10: ffffa00eed02f798 R11: 0000000000000000 R12: ffffa00bbc435200 [63010.899266] R13: ffffa00bf7d39800 R14: 0000000000000400 R15: 0000000000000003 [63010.906399] FS: 0000000000000000(0000) GS:ffffa00eed000000(0000) knlGS:0000000000000000 [63010.914485] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [63010.920229] CR2: 00007f5cfbe99828 CR3: 0000000105efe000 CR4: 00000000003506e0 [63010.927363] Call Trace: [63010.929822] ? bio_reset+0xe/0x40 [63010.933144] ? raid10_alloc_init_r10buf+0x60/0xa0 [raid10] [63010.938629] raid10_sync_request+0x756/0x1610 [raid10] [63010.943770] md_do_sync.cold+0x3e4/0x94c [63010.947698] md_thread+0xab/0x160 [63010.951024] ? md_write_inc+0x50/0x50 [63010.954688] kthread+0x149/0x170 [63010.957923] ? set_kthread_struct+0x40/0x40 [63010.962107] ret_from_fork+0x22/0x30 Removing the code that sets mddev->private to NULL in raid0 can fix problem.

In the Linux kernel, the following vulnerability has been resolved: thermal/drivers/broadcom: Fix potential NULL dereference in sr_thermal_probe platform_get_resource() may return NULL, add proper check to avoid potential NULL dereferencing.

In the Linux kernel, the following vulnerability has been resolved: RDMA/hfi1: Prevent panic when SDMA is disabled If the hfi1 module is loaded with HFI1_CAP_SDMA off, a call to hfi1_write_iter() will dereference a NULL pointer and panic. A typical stack frame is: sdma_select_user_engine [hfi1] hfi1_user_sdma_process_request [hfi1] hfi1_write_iter [hfi1] do_iter_readv_writev do_iter_write vfs_writev do_writev do_syscall_64 The fix is to test for SDMA in hfi1_write_iter() and fail the I/O with EINVAL.

In the Linux kernel, the following vulnerability has been resolved: ASoC: rt711-sdca: fix kernel NULL pointer dereference when IO error The initial settings will be written before the codec probe function. But, the rt711->component doesn't be assigned yet. If IO error happened during initial settings operations, it will cause the kernel panic. This patch changed component->dev to slave->dev to fix this issue.

In the Linux kernel, the following vulnerability has been resolved: media: venus: hfi: avoid null dereference in deinit If venus_probe fails at pm_runtime_put_sync the error handling first calls hfi_destroy and afterwards hfi_core_deinit. As hfi_destroy sets core->ops to NULL, hfi_core_deinit cannot call the core_deinit function anymore. Avoid this null pointer derefence by skipping the call when necessary.

In the Linux kernel, the following vulnerability has been resolved: reset: uniphier-glue: Fix possible null-ptr-deref It will cause null-ptr-deref when resource_size(res) invoked, if platform_get_resource() returns NULL.

In the Linux kernel, the following vulnerability has been resolved: net/sched: taprio: avoid disabling offload when it was never enabled In an incredibly strange API design decision, qdisc->destroy() gets called even if qdisc->init() never succeeded, not exclusively since commit 87b60cfacf9f ("net_sched: fix error recovery at qdisc creation"), but apparently also earlier (in the case of qdisc_create_dflt()). The taprio qdisc does not fully acknowledge this when it attempts full offload, because it starts off with q->flags = TAPRIO_FLAGS_INVALID in taprio_init(), then it replaces q->flags with TCA_TAPRIO_ATTR_FLAGS parsed from netlink (in taprio_change(), tail called from taprio_init()). But in taprio_destroy(), we call taprio_disable_offload(), and this determines what to do based on FULL_OFFLOAD_IS_ENABLED(q->flags). But looking at the implementation of FULL_OFFLOAD_IS_ENABLED() (a bitwise check of bit 1 in q->flags), it is invalid to call this macro on q->flags when it contains TAPRIO_FLAGS_INVALID, because that is set to U32_MAX, and therefore FULL_OFFLOAD_IS_ENABLED() will return true on an invalid set of flags. As a result, it is possible to crash the kernel if user space forces an error between setting q->flags = TAPRIO_FLAGS_INVALID, and the calling of taprio_enable_offload(). This is because drivers do not expect the offload to be disabled when it was never enabled. The error that we force here is to attach taprio as a non-root qdisc, but instead as child of an mqprio root qdisc: $ tc qdisc add dev swp0 root handle 1: \ mqprio num_tc 8 map 0 1 2 3 4 5 6 7 \ queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 0 $ tc qdisc replace dev swp0 parent 1:1 \ taprio num_tc 8 map 0 1 2 3 4 5 6 7 \ queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 base-time 0 \ sched-entry S 0x7f 990000 sched-entry S 0x80 100000 \ flags 0x0 clockid CLOCK_TAI Unable to handle kernel paging request at virtual address fffffffffffffff8 [fffffffffffffff8] pgd=0000000000000000, p4d=0000000000000000 Internal error: Oops: 96000004 [#1] PREEMPT SMP Call trace: taprio_dump+0x27c/0x310 vsc9959_port_setup_tc+0x1f4/0x460 felix_port_setup_tc+0x24/0x3c dsa_slave_setup_tc+0x54/0x27c taprio_disable_offload.isra.0+0x58/0xe0 taprio_destroy+0x80/0x104 qdisc_create+0x240/0x470 tc_modify_qdisc+0x1fc/0x6b0 rtnetlink_rcv_msg+0x12c/0x390 netlink_rcv_skb+0x5c/0x130 rtnetlink_rcv+0x1c/0x2c Fix this by keeping track of the operations we made, and undo the offload only if we actually did it. I've added "bool offloaded" inside a 4 byte hole between "int clockid" and "atomic64_t picos_per_byte". Now the first cache line looks like below: $ pahole -C taprio_sched net/sched/sch_taprio.o struct taprio_sched { struct Qdisc * * qdiscs; /* 0 8 */ struct Qdisc * root; /* 8 8 */ u32 flags; /* 16 4 */ enum tk_offsets tk_offset; /* 20 4 */ int clockid; /* 24 4 */ bool offloaded; /* 28 1 */ /* XXX 3 bytes hole, try to pack */ atomic64_t picos_per_byte; /* 32 0 */ /* XXX 8 bytes hole, try to pack */ spinlock_t current_entry_lock; /* 40 0 */ /* XXX 8 bytes hole, try to pack */ struct sched_entry * current_entry; /* 48 8 */ struct sched_gate_list * oper_sched; /* 56 8 */ /* --- cacheline 1 boundary (64 bytes) --- */

In the Linux kernel, the following vulnerability has been resolved: hwmon: (nct6775) Fix crash in clear_caseopen Paweł Marciniak reports the following crash, observed when clearing the chassis intrusion alarm. BUG: kernel NULL pointer dereference, address: 0000000000000028 PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 3 PID: 4815 Comm: bash Tainted: G S 5.16.2-200.fc35.x86_64 #1 Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./Z97 Extreme4, BIOS P2.60A 05/03/2018 RIP: 0010:clear_caseopen+0x5a/0x120 [nct6775] Code: 68 70 e8 e9 32 b1 e3 85 c0 0f 85 d2 00 00 00 48 83 7c 24 ... RSP: 0018:ffffabcb02803dd8 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000000 RDX: ffff8e8808192880 RSI: 0000000000000000 RDI: ffff8e87c7509a68 RBP: 0000000000000000 R08: 0000000000000001 R09: 000000000000000a R10: 000000000000000a R11: f000000000000000 R12: 000000000000001f R13: ffff8e87c7509828 R14: ffff8e87c7509a68 R15: ffff8e88494527a0 FS: 00007f4db9151740(0000) GS:ffff8e8ebfec0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000028 CR3: 0000000166b66001 CR4: 00000000001706e0 Call Trace: <TASK> kernfs_fop_write_iter+0x11c/0x1b0 new_sync_write+0x10b/0x180 vfs_write+0x209/0x2a0 ksys_write+0x4f/0xc0 do_syscall_64+0x3b/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae The problem is that the device passed to clear_caseopen() is the hwmon device, not the platform device, and the platform data is not set in the hwmon device. Store the pointer to sio_data in struct nct6775_data and get if from there if needed.

In the Linux kernel, the following vulnerability has been resolved: riscv: fix oops caused by irqsoff latency tracer The trace_hardirqs_{on,off}() require the caller to setup frame pointer properly. This because these two functions use macro 'CALLER_ADDR1' (aka. __builtin_return_address(1)) to acquire caller info. If the $fp is used for other purpose, the code generated this macro (as below) could trigger memory access fault. 0xffffffff8011510e <+80>: ld a1,-16(s0) 0xffffffff80115112 <+84>: ld s2,-8(a1) # <-- paging fault here The oops message during booting if compiled with 'irqoff' tracer enabled: [ 0.039615][ T0] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000f8 [ 0.041925][ T0] Oops [#1] [ 0.042063][ T0] Modules linked in: [ 0.042864][ T0] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.17.0-rc1-00233-g9a20c48d1ed2 #29 [ 0.043568][ T0] Hardware name: riscv-virtio,qemu (DT) [ 0.044343][ T0] epc : trace_hardirqs_on+0x56/0xe2 [ 0.044601][ T0] ra : restore_all+0x12/0x6e [ 0.044721][ T0] epc : ffffffff80126a5c ra : ffffffff80003b94 sp : ffffffff81403db0 [ 0.044801][ T0] gp : ffffffff8163acd8 tp : ffffffff81414880 t0 : 0000000000000020 [ 0.044882][ T0] t1 : 0098968000000000 t2 : 0000000000000000 s0 : ffffffff81403de0 [ 0.044967][ T0] s1 : 0000000000000000 a0 : 0000000000000001 a1 : 0000000000000100 [ 0.045046][ T0] a2 : 0000000000000000 a3 : 0000000000000000 a4 : 0000000000000000 [ 0.045124][ T0] a5 : 0000000000000000 a6 : 0000000000000000 a7 : 0000000054494d45 [ 0.045210][ T0] s2 : ffffffff80003b94 s3 : ffffffff81a8f1b0 s4 : ffffffff80e27b50 [ 0.045289][ T0] s5 : ffffffff81414880 s6 : ffffffff8160fa00 s7 : 00000000800120e8 [ 0.045389][ T0] s8 : 0000000080013100 s9 : 000000000000007f s10: 0000000000000000 [ 0.045474][ T0] s11: 0000000000000000 t3 : 7fffffffffffffff t4 : 0000000000000000 [ 0.045548][ T0] t5 : 0000000000000000 t6 : ffffffff814aa368 [ 0.045620][ T0] status: 0000000200000100 badaddr: 00000000000000f8 cause: 000000000000000d [ 0.046402][ T0] [<ffffffff80003b94>] restore_all+0x12/0x6e This because the $fp(aka. $s0) register is not used as frame pointer in the assembly entry code. resume_kernel: REG_L s0, TASK_TI_PREEMPT_COUNT(tp) bnez s0, restore_all REG_L s0, TASK_TI_FLAGS(tp) andi s0, s0, _TIF_NEED_RESCHED beqz s0, restore_all call preempt_schedule_irq j restore_all To fix above issue, here we add one extra level wrapper for function trace_hardirqs_{on,off}() so they can be safely called by low level entry code.

In the Linux kernel, the following vulnerability has been resolved: tty: fix possible null-ptr-defer in spk_ttyio_release Run the following tests on the qemu platform: syzkaller:~# modprobe speakup_audptr input: Speakup as /devices/virtual/input/input4 initialized device: /dev/synth, node (MAJOR 10, MINOR 125) speakup 3.1.6: initialized synth name on entry is: (null) synth probe spk_ttyio_initialise_ldisc failed because tty_kopen_exclusive returned failed (errno -16), then remove the module, we will get a null-ptr-defer problem, as follow: syzkaller:~# modprobe -r speakup_audptr releasing synth audptr BUG: kernel NULL pointer dereference, address: 0000000000000080 #PF: supervisor write access in kernel mode #PF: error_code(0x0002) - not-present page PGD 0 P4D 0 Oops: 0002 [#1] PREEMPT SMP PTI CPU: 2 PID: 204 Comm: modprobe Not tainted 6.1.0-rc6-dirty #1 RIP: 0010:mutex_lock+0x14/0x30 Call Trace: <TASK> spk_ttyio_release+0x19/0x70 [speakup] synth_release.part.6+0xac/0xc0 [speakup] synth_remove+0x56/0x60 [speakup] __x64_sys_delete_module+0x156/0x250 ? fpregs_assert_state_consistent+0x1d/0x50 do_syscall_64+0x37/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd </TASK> Modules linked in: speakup_audptr(-) speakup Dumping ftrace buffer: in_synth->dev was not initialized during modprobe, so we add check for in_synth->dev to fix this bug.

In the Linux kernel, the following vulnerability has been resolved: gpio: mockup: fix NULL pointer dereference when removing debugfs We now remove the device's debugfs entries when unbinding the driver. This now causes a NULL-pointer dereference on module exit because the platform devices are unregistered *after* the global debugfs directory has been recursively removed. Fix it by unregistering the devices first.

In the Linux kernel, the following vulnerability has been resolved: XArray: Fix xas_create_range() when multi-order entry present If there is already an entry present that is of order >= XA_CHUNK_SHIFT when we call xas_create_range(), xas_create_range() will misinterpret that entry as a node and dereference xa_node->parent, generally leading to a crash that looks something like this: general protection fault, probably for non-canonical address 0xdffffc0000000001: 0000 [#1] PREEMPT SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f] CPU: 0 PID: 32 Comm: khugepaged Not tainted 5.17.0-rc8-syzkaller-00003-g56e337f2cf13 #0 RIP: 0010:xa_parent_locked include/linux/xarray.h:1207 [inline] RIP: 0010:xas_create_range+0x2d9/0x6e0 lib/xarray.c:725 It's deterministically reproducable once you know what the problem is, but producing it in a live kernel requires khugepaged to hit a race. While the problem has been present since xas_create_range() was introduced, I'm not aware of a way to hit it before the page cache was converted to use multi-index entries.

In the Linux kernel, the following vulnerability has been resolved: xprtrdma: fix pointer derefs in error cases of rpcrdma_ep_create If there are failures then we must not leave the non-NULL pointers with the error value, otherwise `rpcrdma_ep_destroy` gets confused and tries free them, resulting in an Oops.

In the Linux kernel, the following vulnerability has been resolved: IB/hfi1: Fix AIP early init panic An early failure in hfi1_ipoib_setup_rn() can lead to the following panic: BUG: unable to handle kernel NULL pointer dereference at 00000000000001b0 PGD 0 P4D 0 Oops: 0002 [#1] SMP NOPTI Workqueue: events work_for_cpu_fn RIP: 0010:try_to_grab_pending+0x2b/0x140 Code: 1f 44 00 00 41 55 41 54 55 48 89 d5 53 48 89 fb 9c 58 0f 1f 44 00 00 48 89 c2 fa 66 0f 1f 44 00 00 48 89 55 00 40 84 f6 75 77 <f0> 48 0f ba 2b 00 72 09 31 c0 5b 5d 41 5c 41 5d c3 48 89 df e8 6c RSP: 0018:ffffb6b3cf7cfa48 EFLAGS: 00010046 RAX: 0000000000000246 RBX: 00000000000001b0 RCX: 0000000000000000 RDX: 0000000000000246 RSI: 0000000000000000 RDI: 00000000000001b0 RBP: ffffb6b3cf7cfa70 R08: 0000000000000f09 R09: 0000000000000001 R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000000 R13: ffffb6b3cf7cfa90 R14: ffffffff9b2fbfc0 R15: ffff8a4fdf244690 FS: 0000000000000000(0000) GS:ffff8a527f400000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000000001b0 CR3: 00000017e2410003 CR4: 00000000007706f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: __cancel_work_timer+0x42/0x190 ? dev_printk_emit+0x4e/0x70 iowait_cancel_work+0x15/0x30 [hfi1] hfi1_ipoib_txreq_deinit+0x5a/0x220 [hfi1] ? dev_err+0x6c/0x90 hfi1_ipoib_netdev_dtor+0x15/0x30 [hfi1] hfi1_ipoib_setup_rn+0x10e/0x150 [hfi1] rdma_init_netdev+0x5a/0x80 [ib_core] ? hfi1_ipoib_free_rdma_netdev+0x20/0x20 [hfi1] ipoib_intf_init+0x6c/0x350 [ib_ipoib] ipoib_intf_alloc+0x5c/0xc0 [ib_ipoib] ipoib_add_one+0xbe/0x300 [ib_ipoib] add_client_context+0x12c/0x1a0 [ib_core] enable_device_and_get+0xdc/0x1d0 [ib_core] ib_register_device+0x572/0x6b0 [ib_core] rvt_register_device+0x11b/0x220 [rdmavt] hfi1_register_ib_device+0x6b4/0x770 [hfi1] do_init_one.isra.20+0x3e3/0x680 [hfi1] local_pci_probe+0x41/0x90 work_for_cpu_fn+0x16/0x20 process_one_work+0x1a7/0x360 ? create_worker+0x1a0/0x1a0 worker_thread+0x1cf/0x390 ? create_worker+0x1a0/0x1a0 kthread+0x116/0x130 ? kthread_flush_work_fn+0x10/0x10 ret_from_fork+0x1f/0x40 The panic happens in hfi1_ipoib_txreq_deinit() because there is a NULL deref when hfi1_ipoib_netdev_dtor() is called in this error case. hfi1_ipoib_txreq_init() and hfi1_ipoib_rxq_init() are self unwinding so fix by adjusting the error paths accordingly. Other changes: - hfi1_ipoib_free_rdma_netdev() is deleted including the free_netdev() since the netdev core code deletes calls free_netdev() - The switch to the accelerated entrances is moved to the success path.

In the Linux kernel, the following vulnerability has been resolved: staging: vchiq_arm: Avoid NULL ptr deref in vchiq_dump_platform_instances vchiq_get_state() can return a NULL pointer. So handle this cases and avoid a NULL pointer derefence in vchiq_dump_platform_instances.

In the Linux kernel, the following vulnerability has been resolved: qede: confirm skb is allocated before using qede_build_skb() assumes build_skb() always works and goes straight to skb_reserve(). However, build_skb() can fail under memory pressure. This results in a kernel panic because the skb to reserve is NULL. Add a check in case build_skb() failed to allocate and return NULL. The NULL return is handled correctly in callers to qede_build_skb().

In the Linux kernel, the following vulnerability has been resolved: drm/panel: ili9341: fix optional regulator handling If the optional regulator lookup fails, reset the pointer to NULL. Other functions such as mipi_dbi_poweron_reset_conditional() only do a NULL pointer check and will otherwise dereference the error pointer.

In the Linux kernel, the following vulnerability has been resolved: ice: Fix crash by keep old cfg when update TCs more than queues There are problems if allocated queues less than Traffic Classes. Commit a632b2a4c920 ("ice: ethtool: Prohibit improper channel config for DCB") already disallow setting less queues than TCs. Another case is if we first set less queues, and later update more TCs config due to LLDP, ice_vsi_cfg_tc() will failed but left dirty num_txq/rxq and tc_cfg in vsi, that will cause invalid pointer access. [ 95.968089] ice 0000:3b:00.1: More TCs defined than queues/rings allocated. [ 95.968092] ice 0000:3b:00.1: Trying to use more Rx queues (8), than were allocated (1)! [ 95.968093] ice 0000:3b:00.1: Failed to config TC for VSI index: 0 [ 95.969621] general protection fault: 0000 [#1] SMP NOPTI [ 95.969705] CPU: 1 PID: 58405 Comm: lldpad Kdump: loaded Tainted: G U W O --------- -t - 4.18.0 #1 [ 95.969867] Hardware name: O.E.M/BC11SPSCB10, BIOS 8.23 12/30/2021 [ 95.969992] RIP: 0010:devm_kmalloc+0xa/0x60 [ 95.970052] Code: 5c ff ff ff 31 c0 5b 5d 41 5c c3 b8 f4 ff ff ff eb f4 0f 1f 40 00 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 89 d1 <8b> 97 60 02 00 00 48 8d 7e 18 48 39 f7 72 3f 55 89 ce 53 48 8b 4c [ 95.970344] RSP: 0018:ffffc9003f553888 EFLAGS: 00010206 [ 95.970425] RAX: dead000000000200 RBX: ffffea003c425b00 RCX: 00000000006080c0 [ 95.970536] RDX: 00000000006080c0 RSI: 0000000000000200 RDI: dead000000000200 [ 95.970648] RBP: dead000000000200 R08: 00000000000463c0 R09: ffff888ffa900000 [ 95.970760] R10: 0000000000000000 R11: 0000000000000002 R12: ffff888ff6b40100 [ 95.970870] R13: ffff888ff6a55018 R14: 0000000000000000 R15: ffff888ff6a55460 [ 95.970981] FS: 00007f51b7d24700(0000) GS:ffff88903ee80000(0000) knlGS:0000000000000000 [ 95.971108] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 95.971197] CR2: 00007fac5410d710 CR3: 0000000f2c1de002 CR4: 00000000007606e0 [ 95.971309] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 95.971419] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 95.971530] PKRU: 55555554 [ 95.971573] Call Trace: [ 95.971622] ice_setup_rx_ring+0x39/0x110 [ice] [ 95.971695] ice_vsi_setup_rx_rings+0x54/0x90 [ice] [ 95.971774] ice_vsi_open+0x25/0x120 [ice] [ 95.971843] ice_open_internal+0xb8/0x1f0 [ice] [ 95.971919] ice_ena_vsi+0x4f/0xd0 [ice] [ 95.971987] ice_dcb_ena_dis_vsi.constprop.5+0x29/0x90 [ice] [ 95.972082] ice_pf_dcb_cfg+0x29a/0x380 [ice] [ 95.972154] ice_dcbnl_setets+0x174/0x1b0 [ice] [ 95.972220] dcbnl_ieee_set+0x89/0x230 [ 95.972279] ? dcbnl_ieee_del+0x150/0x150 [ 95.972341] dcb_doit+0x124/0x1b0 [ 95.972392] rtnetlink_rcv_msg+0x243/0x2f0 [ 95.972457] ? dcb_doit+0x14d/0x1b0 [ 95.972510] ? __kmalloc_node_track_caller+0x1d3/0x280 [ 95.972591] ? rtnl_calcit.isra.31+0x100/0x100 [ 95.972661] netlink_rcv_skb+0xcf/0xf0 [ 95.972720] netlink_unicast+0x16d/0x220 [ 95.972781] netlink_sendmsg+0x2ba/0x3a0 [ 95.975891] sock_sendmsg+0x4c/0x50 [ 95.979032] ___sys_sendmsg+0x2e4/0x300 [ 95.982147] ? kmem_cache_alloc+0x13e/0x190 [ 95.985242] ? __wake_up_common_lock+0x79/0x90 [ 95.988338] ? __check_object_size+0xac/0x1b0 [ 95.991440] ? _copy_to_user+0x22/0x30 [ 95.994539] ? move_addr_to_user+0xbb/0xd0 [ 95.997619] ? __sys_sendmsg+0x53/0x80 [ 96.000664] __sys_sendmsg+0x53/0x80 [ 96.003747] do_syscall_64+0x5b/0x1d0 [ 96.006862] entry_SYSCALL_64_after_hwframe+0x65/0xca Only update num_txq/rxq when passed check, and restore tc_cfg if setup queue map failed.

In the Linux kernel, the following vulnerability has been resolved: can: af_can: fix NULL pointer dereference in can_rcv_filter Analogue to commit 8aa59e355949 ("can: af_can: fix NULL pointer dereference in can_rx_register()") we need to check for a missing initialization of ml_priv in the receive path of CAN frames. Since commit 4e096a18867a ("net: introduce CAN specific pointer in the struct net_device") the check for dev->type to be ARPHRD_CAN is not sufficient anymore since bonding or tun netdevices claim to be CAN devices but do not initialize ml_priv accordingly.

In the Linux kernel, the following vulnerability has been resolved: thermal: core: Fix TZ_GET_TRIP NULL pointer dereference Do not call get_trip_hyst() from thermal_genl_cmd_tz_get_trip() if the thermal zone does not define one.

In the Linux kernel, the following vulnerability has been resolved: perf/x86/intel/pt: Fix crash with stop filters in single-range mode Add a check for !buf->single before calling pt_buffer_region_size in a place where a missing check can cause a kernel crash. Fixes a bug introduced by commit 670638477aed ("perf/x86/intel/pt: Opportunistically use single range output mode"), which added a support for PT single-range output mode. Since that commit if a PT stop filter range is hit while tracing, the kernel will crash because of a null pointer dereference in pt_handle_status due to calling pt_buffer_region_size without a ToPA configured. The commit which introduced single-range mode guarded almost all uses of the ToPA buffer variables with checks of the buf->single variable, but missed the case where tracing was stopped by the PT hardware, which happens when execution hits a configured stop filter. Tested that hitting a stop filter while PT recording successfully records a trace with this patch but crashes without this patch.

kvm_pv_send_ipi in arch/x86/kvm/lapic.c in the Linux kernel through 4.19.2 allows local users to cause a denial of service (NULL pointer dereference and BUG) via crafted system calls that reach a situation where the apic map is uninitialized.

In the Linux kernel, the following vulnerability has been resolved: SUNRPC: Fix the svc_deferred_event trace class Fix a NULL deref crash that occurs when an svc_rqst is deferred while the sunrpc tracing subsystem is enabled. svc_revisit() sets dr->xprt to NULL, so it can't be relied upon in the tracepoint to provide the remote's address. Unfortunately we can't revert the "svc_deferred_class" hunk in commit ece200ddd54b ("sunrpc: Save remote presentation address in svc_xprt for trace events") because there is now a specific check of event format specifiers for unsafe dereferences. The warning that check emits is: event svc_defer_recv has unsafe dereference of argument 1 A "%pISpc" format specifier with a "struct sockaddr *" is indeed flagged by this check. Instead, take the brute-force approach used by the svcrdma_qp_error tracepoint. Convert the dr::addr field into a presentation address in the TP_fast_assign() arm of the trace event, and store that as a string. This fix can be backported to -stable kernels. In the meantime, commit c6ced22997ad ("tracing: Update print fmt check to handle new __get_sockaddr() macro") is now in v5.18, so this wonky fix can be replaced with __sockaddr() and friends properly during the v5.19 merge window.

In the Linux kernel, the following vulnerability has been resolved: gpio: Restrict usage of GPIO chip irq members before initialization GPIO chip irq members are exposed before they could be completely initialized and this leads to race conditions. One such issue was observed for the gc->irq.domain variable which was accessed through the I2C interface in gpiochip_to_irq() before it could be initialized by gpiochip_add_irqchip(). This resulted in Kernel NULL pointer dereference. Following are the logs for reference :- kernel: Call Trace: kernel: gpiod_to_irq+0x53/0x70 kernel: acpi_dev_gpio_irq_get_by+0x113/0x1f0 kernel: i2c_acpi_get_irq+0xc0/0xd0 kernel: i2c_device_probe+0x28a/0x2a0 kernel: really_probe+0xf2/0x460 kernel: RIP: 0010:gpiochip_to_irq+0x47/0xc0 To avoid such scenarios, restrict usage of GPIO chip irq members before they are completely initialized.

In the Linux kernel, the following vulnerability has been resolved: can: slcan: fix freed work crash The LTP test pty03 is causing a crash in slcan: BUG: kernel NULL pointer dereference, address: 0000000000000008 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 0 PID: 348 Comm: kworker/0:3 Not tainted 6.0.8-1-default #1 openSUSE Tumbleweed 9d20364b934f5aab0a9bdf84e8f45cfdfae39dab Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.15.0-0-g2dd4b9b-rebuilt.opensuse.org 04/01/2014 Workqueue: 0x0 (events) RIP: 0010:process_one_work (/home/rich/kernel/linux/kernel/workqueue.c:706 /home/rich/kernel/linux/kernel/workqueue.c:2185) Code: 49 89 ff 41 56 41 55 41 54 55 53 48 89 f3 48 83 ec 10 48 8b 06 48 8b 6f 48 49 89 c4 45 30 e4 a8 04 b8 00 00 00 00 4c 0f 44 e0 <49> 8b 44 24 08 44 8b a8 00 01 00 00 41 83 e5 20 f6 45 10 04 75 0e RSP: 0018:ffffaf7b40f47e98 EFLAGS: 00010046 RAX: 0000000000000000 RBX: ffff9d644e1b8b48 RCX: ffff9d649e439968 RDX: 00000000ffff8455 RSI: ffff9d644e1b8b48 RDI: ffff9d64764aa6c0 RBP: ffff9d649e4335c0 R08: 0000000000000c00 R09: ffff9d64764aa734 R10: 0000000000000007 R11: 0000000000000001 R12: 0000000000000000 R13: ffff9d649e4335e8 R14: ffff9d64490da780 R15: ffff9d64764aa6c0 FS: 0000000000000000(0000) GS:ffff9d649e400000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000008 CR3: 0000000036424000 CR4: 00000000000006f0 Call Trace: <TASK> worker_thread (/home/rich/kernel/linux/kernel/workqueue.c:2436) kthread (/home/rich/kernel/linux/kernel/kthread.c:376) ret_from_fork (/home/rich/kernel/linux/arch/x86/entry/entry_64.S:312) Apparently, the slcan's tx_work is freed while being scheduled. While slcan_netdev_close() (netdev side) calls flush_work(&sl->tx_work), slcan_close() (tty side) does not. So when the netdev is never set UP, but the tty is stuffed with bytes and forced to wakeup write, the work is scheduled, but never flushed. So add an additional flush_work() to slcan_close() to be sure the work is flushed under all circumstances. The Fixes commit below moved flush_work() from slcan_close() to slcan_netdev_close(). What was the rationale behind it? Maybe we can drop the one in slcan_netdev_close()? I see the same pattern in can327. So it perhaps needs the very same fix.