In the Linux kernel, the following vulnerability has been resolved: dmaengine: dw-axi-dmac: do not print NULL LLI during error During debugging we have seen an issue where axi_chan_dump_lli() is passed a NULL LLI pointer which ends up causing an OOPS due to trying to get fields from it. Simply print NULL LLI and exit to avoid this.

In the Linux kernel, the following vulnerability has been resolved: ALSA: pcm: Check for null pointer of pointer substream before dereferencing it Pointer substream is being dereferenced on the assignment of pointer card before substream is being null checked with the macro PCM_RUNTIME_CHECK. Although PCM_RUNTIME_CHECK calls BUG_ON, it still is useful to perform the the pointer check before card is assigned.

In the Linux kernel, the following vulnerability has been resolved: phy: qcom-qmp-combo: fix NULL-deref on runtime resume Commit fc64623637da ("phy: qcom-qmp-combo,usb: add support for separate PCS_USB region") started treating the PCS_USB registers as potentially separate from the PCS registers but used the wrong base when no PCS_USB offset has been provided. Fix the PCS_USB base used at runtime resume to prevent dereferencing a NULL pointer on platforms that do not provide a PCS_USB offset (e.g. SC7180).

In the Linux kernel, the following vulnerability has been resolved: spi: bcm2835: bcm2835_spi_handle_err(): fix NULL pointer deref for non DMA transfers In case a IRQ based transfer times out the bcm2835_spi_handle_err() function is called. Since commit 1513ceee70f2 ("spi: bcm2835: Drop dma_pending flag") the TX and RX DMA transfers are unconditionally canceled, leading to NULL pointer derefs if ctlr->dma_tx or ctlr->dma_rx are not set. Fix the NULL pointer deref by checking that ctlr->dma_tx and ctlr->dma_rx are valid pointers before accessing them.

In the Linux kernel, the following vulnerability has been resolved: net: microchip: sparx5: Fix potential null-ptr-deref in sparx_stats_init() and sparx5_start() sparx_stats_init() calls create_singlethread_workqueue() and not checked the ret value, which may return NULL. And a null-ptr-deref may happen: sparx_stats_init() create_singlethread_workqueue() # failed, sparx5->stats_queue is NULL queue_delayed_work() queue_delayed_work_on() __queue_delayed_work() # warning here, but continue __queue_work() # access wq->flags, null-ptr-deref Check the ret value and return -ENOMEM if it is NULL. So as sparx5_start().

In the Linux kernel, the following vulnerability has been resolved: media: venus: hfi: avoid null dereference in deinit If venus_probe fails at pm_runtime_put_sync the error handling first calls hfi_destroy and afterwards hfi_core_deinit. As hfi_destroy sets core->ops to NULL, hfi_core_deinit cannot call the core_deinit function anymore. Avoid this null pointer derefence by skipping the call when necessary.

In the Linux kernel, the following vulnerability has been resolved: vduse: Fix NULL pointer dereference on sysfs access The control device has no drvdata. So we will get a NULL pointer dereference when accessing control device's msg_timeout attribute via sysfs: [ 132.841881][ T3644] BUG: kernel NULL pointer dereference, address: 00000000000000f8 [ 132.850619][ T3644] RIP: 0010:msg_timeout_show (drivers/vdpa/vdpa_user/vduse_dev.c:1271) [ 132.869447][ T3644] dev_attr_show (drivers/base/core.c:2094) [ 132.870215][ T3644] sysfs_kf_seq_show (fs/sysfs/file.c:59) [ 132.871164][ T3644] ? device_remove_bin_file (drivers/base/core.c:2088) [ 132.872082][ T3644] kernfs_seq_show (fs/kernfs/file.c:164) [ 132.872838][ T3644] seq_read_iter (fs/seq_file.c:230) [ 132.873578][ T3644] ? __vmalloc_area_node (mm/vmalloc.c:3041) [ 132.874532][ T3644] kernfs_fop_read_iter (fs/kernfs/file.c:238) [ 132.875513][ T3644] __kernel_read (fs/read_write.c:440 (discriminator 1)) [ 132.876319][ T3644] kernel_read (fs/read_write.c:459) [ 132.877129][ T3644] kernel_read_file (fs/kernel_read_file.c:94) [ 132.877978][ T3644] kernel_read_file_from_fd (include/linux/file.h:45 fs/kernel_read_file.c:186) [ 132.879019][ T3644] __do_sys_finit_module (kernel/module.c:4207) [ 132.879930][ T3644] __ia32_sys_finit_module (kernel/module.c:4189) [ 132.880930][ T3644] do_int80_syscall_32 (arch/x86/entry/common.c:112 arch/x86/entry/common.c:132) [ 132.881847][ T3644] entry_INT80_compat (arch/x86/entry/entry_64_compat.S:419) To fix it, don't create the unneeded attribute for control device anymore.

In the Linux kernel, the following vulnerability has been resolved: powerpc/64s: Don't use DSISR for SLB faults Since commit 46ddcb3950a2 ("powerpc/mm: Show if a bad page fault on data is read or write.") we use page_fault_is_write(regs->dsisr) in __bad_page_fault() to determine if the fault is for a read or write, and change the message printed accordingly. But SLB faults, aka Data Segment Interrupts, don't set DSISR (Data Storage Interrupt Status Register) to a useful value. All ISA versions from v2.03 through v3.1 specify that the Data Segment Interrupt sets DSISR "to an undefined value". As far as I can see there's no mention of SLB faults setting DSISR in any BookIV content either. This manifests as accesses that should be a read being incorrectly reported as writes, for example, using the xmon "dump" command: 0:mon> d 0x5deadbeef0000000 5deadbeef0000000 [359526.415354][ C6] BUG: Unable to handle kernel data access on write at 0x5deadbeef0000000 [359526.415611][ C6] Faulting instruction address: 0xc00000000010a300 cpu 0x6: Vector: 380 (Data SLB Access) at [c00000000ffbf400] pc: c00000000010a300: mread+0x90/0x190 If we disassemble the PC, we see a load instruction: 0:mon> di c00000000010a300 c00000000010a300 89490000 lbz r10,0(r9) We can also see in exceptions-64s.S that the data_access_slb block doesn't set IDSISR=1, which means it doesn't load DSISR into pt_regs. So the value we're using to determine if the fault is a read/write is some stale value in pt_regs from a previous page fault. Rework the printing logic to separate the SLB fault case out, and only print read/write in the cases where we can determine it. The result looks like eg: 0:mon> d 0x5deadbeef0000000 5deadbeef0000000 [ 721.779525][ C6] BUG: Unable to handle kernel data access at 0x5deadbeef0000000 [ 721.779697][ C6] Faulting instruction address: 0xc00000000014cbe0 cpu 0x6: Vector: 380 (Data SLB Access) at [c00000000ffbf390] 0:mon> d 0 0000000000000000 [ 742.793242][ C6] BUG: Kernel NULL pointer dereference at 0x00000000 [ 742.793316][ C6] Faulting instruction address: 0xc00000000014cbe0 cpu 0x6: Vector: 380 (Data SLB Access) at [c00000000ffbf390]

In the Linux kernel, the following vulnerability has been resolved: Revert "usb: typec: ucsi: add a common function ucsi_unregister_connectors()" The recent commit 87d0e2f41b8c ("usb: typec: ucsi: add a common function ucsi_unregister_connectors()") introduced a regression that caused NULL dereference at reading the power supply sysfs. It's a stale sysfs entry that should have been removed but remains with NULL ops. The commit changed the error handling to skip the entries after a NULL con->wq, and this leaves the power device unreleased. For addressing the regression, the straight revert is applied here. Further code improvements can be done from the scratch again.

In the Linux kernel, the following vulnerability has been resolved: net: dsa: mv88e6060: prevent crash on an unused port If the port isn't a CPU port nor a user port, 'cpu_dp' is a null pointer and a crash happened on dereferencing it in mv88e6060_setup_port(): [ 9.575872] Unable to handle kernel NULL pointer dereference at virtual address 00000014 ... [ 9.942216] mv88e6060_setup from dsa_register_switch+0x814/0xe84 [ 9.948616] dsa_register_switch from mdio_probe+0x2c/0x54 [ 9.954433] mdio_probe from really_probe.part.0+0x98/0x2a0 [ 9.960375] really_probe.part.0 from driver_probe_device+0x30/0x10c [ 9.967029] driver_probe_device from __device_attach_driver+0xb8/0x13c [ 9.973946] __device_attach_driver from bus_for_each_drv+0x90/0xe0 [ 9.980509] bus_for_each_drv from __device_attach+0x110/0x184 [ 9.986632] __device_attach from bus_probe_device+0x8c/0x94 [ 9.992577] bus_probe_device from deferred_probe_work_func+0x78/0xa8 [ 9.999311] deferred_probe_work_func from process_one_work+0x290/0x73c [ 10.006292] process_one_work from worker_thread+0x30/0x4b8 [ 10.012155] worker_thread from kthread+0xd4/0x10c [ 10.017238] kthread from ret_from_fork+0x14/0x3c

In the Linux kernel, the following vulnerability has been resolved: rose: Fix NULL pointer dereference in rose_send_frame() The syzkaller reported an issue: KASAN: null-ptr-deref in range [0x0000000000000380-0x0000000000000387] CPU: 0 PID: 4069 Comm: kworker/0:15 Not tainted 6.0.0-syzkaller-02734-g0326074ff465 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/22/2022 Workqueue: rcu_gp srcu_invoke_callbacks RIP: 0010:rose_send_frame+0x1dd/0x2f0 net/rose/rose_link.c:101 Call Trace: <IRQ> rose_transmit_clear_request+0x1d5/0x290 net/rose/rose_link.c:255 rose_rx_call_request+0x4c0/0x1bc0 net/rose/af_rose.c:1009 rose_loopback_timer+0x19e/0x590 net/rose/rose_loopback.c:111 call_timer_fn+0x1a0/0x6b0 kernel/time/timer.c:1474 expire_timers kernel/time/timer.c:1519 [inline] __run_timers.part.0+0x674/0xa80 kernel/time/timer.c:1790 __run_timers kernel/time/timer.c:1768 [inline] run_timer_softirq+0xb3/0x1d0 kernel/time/timer.c:1803 __do_softirq+0x1d0/0x9c8 kernel/softirq.c:571 [...] </IRQ> It triggers NULL pointer dereference when 'neigh->dev->dev_addr' is called in the rose_send_frame(). It's the first occurrence of the `neigh` is in rose_loopback_timer() as `rose_loopback_neigh', and the 'dev' in 'rose_loopback_neigh' is initialized sa nullptr. It had been fixed by commit 3b3fd068c56e3fbea30090859216a368398e39bf ("rose: Fix Null pointer dereference in rose_send_frame()") ever. But it's introduced by commit 3c53cd65dece47dd1f9d3a809f32e59d1d87b2b8 ("rose: check NULL rose_loopback_neigh->loopback") again. We fix it by add NULL check in rose_transmit_clear_request(). When the 'dev' in 'neigh' is NULL, we don't reply the request and just clear it. syzkaller don't provide repro, and I provide a syz repro like: r0 = syz_init_net_socket$bt_sco(0x1f, 0x5, 0x2) ioctl$sock_inet_SIOCSIFFLAGS(r0, 0x8914, &(0x7f0000000180)={'rose0\x00', 0x201}) r1 = syz_init_net_socket$rose(0xb, 0x5, 0x0) bind$rose(r1, &(0x7f00000000c0)=@full={0xb, @dev, @null, 0x0, [@null, @null, @netrom, @netrom, @default, @null]}, 0x40) connect$rose(r1, &(0x7f0000000240)=@short={0xb, @dev={0xbb, 0xbb, 0xbb, 0x1, 0x0}, @remote={0xcc, 0xcc, 0xcc, 0xcc, 0xcc, 0xcc, 0x1}, 0x1, @netrom={0xbb, 0xbb, 0xbb, 0xbb, 0xbb, 0x0, 0x0}}, 0x1c)

In the Linux kernel, the following vulnerability has been resolved: rtc: mt6397: check return value after calling platform_get_resource() It will cause null-ptr-deref if platform_get_resource() returns NULL, we need check the return value.

In the Linux kernel, the following vulnerability has been resolved: IB/hfi1: Correctly move list in sc_disable() Commit 13bac861952a ("IB/hfi1: Fix abba locking issue with sc_disable()") incorrectly tries to move a list from one list head to another. The result is a kernel crash. The crash is triggered when a link goes down and there are waiters for a send to complete. The following signature is seen: BUG: kernel NULL pointer dereference, address: 0000000000000030 [...] Call Trace: sc_disable+0x1ba/0x240 [hfi1] pio_freeze+0x3d/0x60 [hfi1] handle_freeze+0x27/0x1b0 [hfi1] process_one_work+0x1b0/0x380 ? process_one_work+0x380/0x380 worker_thread+0x30/0x360 ? process_one_work+0x380/0x380 kthread+0xd7/0x100 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork+0x1f/0x30 The fix is to use the correct call to move the list.

In the Linux kernel, the following vulnerability has been resolved: cxl/region: Fix decoder allocation crash When an intermediate port's decoders have been exhausted by existing regions, and creating a new region with the port in question in it's hierarchical path is attempted, cxl_port_attach_region() fails to find a port decoder (as would be expected), and drops into the failure / cleanup path. However, during cleanup of the region reference, a sanity check attempts to dereference the decoder, which in the above case didn't exist. This causes a NULL pointer dereference BUG. To fix this, refactor the decoder allocation and de-allocation into helper routines, and in this 'free' routine, check that the decoder, @cxld, is valid before attempting any operations on it.

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: Don't finalize CSA in IBSS mode if state is disconnected When we are not connected to a channel, sending channel "switch" announcement doesn't make any sense. The BSS list is empty in that case. This causes the for loop in cfg80211_get_bss() to be bypassed, so the function returns NULL (check line 1424 of net/wireless/scan.c), causing the WARN_ON() in ieee80211_ibss_csa_beacon() to get triggered (check line 500 of net/mac80211/ibss.c), which was consequently reported on the syzkaller dashboard. Thus, check if we have an existing connection before generating the CSA beacon in ieee80211_ibss_finish_csa().

In the Linux kernel, the following vulnerability has been resolved: ASoC: SOF: Intel: hda-ipc: Do not process IPC reply before firmware boot It is not yet clear, but it is possible to create a firmware so broken that it will send a reply message before a FW_READY message (it is not yet clear if FW_READY will arrive later). Since the reply_data is allocated only after the FW_READY message, this will lead to a NULL pointer dereference if not filtered out. The issue was reported with IPC4 firmware but the same condition is present for IPC3.

In the Linux kernel, the following vulnerability has been resolved: ALSA: jack: Access input_dev under mutex It is possible when using ASoC that input_dev is unregistered while calling snd_jack_report, which causes NULL pointer dereference. In order to prevent this serialize access to input_dev using mutex lock.

In the Linux kernel, the following vulnerability has been resolved: ASoC: rt7*-sdw: harden jack_detect_handler Realtek headset codec drivers typically check if the card is instantiated before proceeding with the jack detection. The rt700, rt711 and rt711-sdca are however missing a check on the card pointer, which can lead to NULL dereferences encountered in driver bind/unbind tests.

In the Linux kernel, the following vulnerability has been resolved: SUNRPC: Fix null-ptr-deref when xps sysfs alloc failed There is a null-ptr-deref when xps sysfs alloc failed: BUG: KASAN: null-ptr-deref in sysfs_do_create_link_sd+0x40/0xd0 Read of size 8 at addr 0000000000000030 by task gssproxy/457 CPU: 5 PID: 457 Comm: gssproxy Not tainted 6.0.0-09040-g02357b27ee03 #9 Call Trace: <TASK> dump_stack_lvl+0x34/0x44 kasan_report+0xa3/0x120 sysfs_do_create_link_sd+0x40/0xd0 rpc_sysfs_client_setup+0x161/0x1b0 rpc_new_client+0x3fc/0x6e0 rpc_create_xprt+0x71/0x220 rpc_create+0x1d4/0x350 gssp_rpc_create+0xc3/0x160 set_gssp_clnt+0xbc/0x140 write_gssp+0x116/0x1a0 proc_reg_write+0xd6/0x130 vfs_write+0x177/0x690 ksys_write+0xb9/0x150 do_syscall_64+0x35/0x80 entry_SYSCALL_64_after_hwframe+0x46/0xb0 When the xprt_switch sysfs alloc failed, should not add xprt and switch sysfs to it, otherwise, maybe null-ptr-deref; also initialize the 'xps_sysfs' to NULL to avoid oops when destroy it.

In the Linux kernel, the following vulnerability has been resolved: ring-buffer: Check for NULL cpu_buffer in ring_buffer_wake_waiters() On some machines the number of listed CPUs may be bigger than the actual CPUs that exist. The tracing subsystem allocates a per_cpu directory with access to the per CPU ring buffer via a cpuX file. But to save space, the ring buffer will only allocate buffers for online CPUs, even though the CPU array will be as big as the nr_cpu_ids. With the addition of waking waiters on the ring buffer when closing the file, the ring_buffer_wake_waiters() now needs to make sure that the buffer is allocated (with the irq_work allocated with it) before trying to wake waiters, as it will cause a NULL pointer dereference. While debugging this, I added a NULL check for the buffer itself (which is OK to do), and also NULL pointer checks against buffer->buffers (which is not fine, and will WARN) as well as making sure the CPU number passed in is within the nr_cpu_ids (which is also not fine if it isn't). Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=1204705

In the Linux kernel, the following vulnerability has been resolved: drm/msm/dp: populate connector of struct dp_panel DP CTS test case 4.2.2.6 has valid edid with bad checksum on purpose and expect DP source return correct checksum. During drm edid read, correct edid checksum is calculated and stored at connector::real_edid_checksum. The problem is struct dp_panel::connector never be assigned, instead the connector is stored in struct msm_dp::connector. When we run compliance testing test case 4.2.2.6 dp_panel_handle_sink_request() won't have a valid edid set in struct dp_panel::edid so we'll try to use the connectors real_edid_checksum and hit a NULL pointer dereference error because the connector pointer is never assigned. Changes in V2: -- populate panel connector at msm_dp_modeset_init() instead of at dp_panel_read_sink_caps() Changes in V3: -- remove unhelpful kernel crash trace commit text -- remove renaming dp_display parameter to dp Changes in V4: -- add more details to commit text Changes in v10: -- group into one series Changes in v11: -- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read Signee-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix NULL pointer dereference in nilfs_palloc_commit_free_entry() Syzbot reported a null-ptr-deref bug: NILFS (loop0): segctord starting. Construction interval = 5 seconds, CP frequency < 30 seconds general protection fault, probably for non-canonical address 0xdffffc0000000002: 0000 [#1] PREEMPT SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017] CPU: 1 PID: 3603 Comm: segctord Not tainted 6.1.0-rc2-syzkaller-00105-gb229b6ca5abb #0 Hardware name: Google Compute Engine/Google Compute Engine, BIOS Google 10/11/2022 RIP: 0010:nilfs_palloc_commit_free_entry+0xe5/0x6b0 fs/nilfs2/alloc.c:608 Code: 00 00 00 00 fc ff df 80 3c 02 00 0f 85 cd 05 00 00 48 b8 00 00 00 00 00 fc ff df 4c 8b 73 08 49 8d 7e 10 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 26 05 00 00 49 8b 46 10 be a6 00 00 00 48 c7 c7 RSP: 0018:ffffc90003dff830 EFLAGS: 00010212 RAX: dffffc0000000000 RBX: ffff88802594e218 RCX: 000000000000000d RDX: 0000000000000002 RSI: 0000000000002000 RDI: 0000000000000010 RBP: ffff888071880222 R08: 0000000000000005 R09: 000000000000003f R10: 000000000000000d R11: 0000000000000000 R12: ffff888071880158 R13: ffff88802594e220 R14: 0000000000000000 R15: 0000000000000004 FS: 0000000000000000(0000) GS:ffff8880b9b00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fb1c08316a8 CR3: 0000000018560000 CR4: 0000000000350ee0 Call Trace: <TASK> nilfs_dat_commit_free fs/nilfs2/dat.c:114 [inline] nilfs_dat_commit_end+0x464/0x5f0 fs/nilfs2/dat.c:193 nilfs_dat_commit_update+0x26/0x40 fs/nilfs2/dat.c:236 nilfs_btree_commit_update_v+0x87/0x4a0 fs/nilfs2/btree.c:1940 nilfs_btree_commit_propagate_v fs/nilfs2/btree.c:2016 [inline] nilfs_btree_propagate_v fs/nilfs2/btree.c:2046 [inline] nilfs_btree_propagate+0xa00/0xd60 fs/nilfs2/btree.c:2088 nilfs_bmap_propagate+0x73/0x170 fs/nilfs2/bmap.c:337 nilfs_collect_file_data+0x45/0xd0 fs/nilfs2/segment.c:568 nilfs_segctor_apply_buffers+0x14a/0x470 fs/nilfs2/segment.c:1018 nilfs_segctor_scan_file+0x3f4/0x6f0 fs/nilfs2/segment.c:1067 nilfs_segctor_collect_blocks fs/nilfs2/segment.c:1197 [inline] nilfs_segctor_collect fs/nilfs2/segment.c:1503 [inline] nilfs_segctor_do_construct+0x12fc/0x6af0 fs/nilfs2/segment.c:2045 nilfs_segctor_construct+0x8e3/0xb30 fs/nilfs2/segment.c:2379 nilfs_segctor_thread_construct fs/nilfs2/segment.c:2487 [inline] nilfs_segctor_thread+0x3c3/0xf30 fs/nilfs2/segment.c:2570 kthread+0x2e4/0x3a0 kernel/kthread.c:376 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:306 </TASK> ... If DAT metadata file is corrupted on disk, there is a case where req->pr_desc_bh is NULL and blocknr is 0 at nilfs_dat_commit_end() during a b-tree operation that cascadingly updates ancestor nodes of the b-tree, because nilfs_dat_commit_alloc() for a lower level block can initialize the blocknr on the same DAT entry between nilfs_dat_prepare_end() and nilfs_dat_commit_end(). If this happens, nilfs_dat_commit_end() calls nilfs_dat_commit_free() without valid buffer heads in req->pr_desc_bh and req->pr_bitmap_bh, and causes the NULL pointer dereference above in nilfs_palloc_commit_free_entry() function, which leads to a crash. Fix this by adding a NULL check on req->pr_desc_bh and req->pr_bitmap_bh before nilfs_palloc_commit_free_entry() in nilfs_dat_commit_free(). This also calls nilfs_error() in that case to notify that there is a fatal flaw in the filesystem metadata and prevent further operations.

In the Linux kernel, the following vulnerability has been resolved: SUNRPC: Fix the svc_deferred_event trace class Fix a NULL deref crash that occurs when an svc_rqst is deferred while the sunrpc tracing subsystem is enabled. svc_revisit() sets dr->xprt to NULL, so it can't be relied upon in the tracepoint to provide the remote's address. Unfortunately we can't revert the "svc_deferred_class" hunk in commit ece200ddd54b ("sunrpc: Save remote presentation address in svc_xprt for trace events") because there is now a specific check of event format specifiers for unsafe dereferences. The warning that check emits is: event svc_defer_recv has unsafe dereference of argument 1 A "%pISpc" format specifier with a "struct sockaddr *" is indeed flagged by this check. Instead, take the brute-force approach used by the svcrdma_qp_error tracepoint. Convert the dr::addr field into a presentation address in the TP_fast_assign() arm of the trace event, and store that as a string. This fix can be backported to -stable kernels. In the meantime, commit c6ced22997ad ("tracing: Update print fmt check to handle new __get_sockaddr() macro") is now in v5.18, so this wonky fix can be replaced with __sockaddr() and friends properly during the v5.19 merge window.

In the Linux kernel, the following vulnerability has been resolved: drm/msm/dsi: invalid parameter check in msm_dsi_phy_enable The function performs a check on the "phy" input parameter, however, it is used before the check. Initialize the "dev" variable after the sanity check to avoid a possible NULL pointer dereference. Addresses-Coverity-ID: 1493860 ("Null pointer dereference")

In the Linux kernel, the following vulnerability has been resolved: drm/radeon: fix a possible null pointer dereference In radeon_fp_native_mode(), the return value of drm_mode_duplicate() is assigned to mode, which will lead to a NULL pointer dereference on failure of drm_mode_duplicate(). Add a check to avoid npd. The failure status of drm_cvt_mode() on the other path is checked too.

In the Linux kernel, the following vulnerability has been resolved: gpio: mockup: fix NULL pointer dereference when removing debugfs We now remove the device's debugfs entries when unbinding the driver. This now causes a NULL-pointer dereference on module exit because the platform devices are unregistered *after* the global debugfs directory has been recursively removed. Fix it by unregistering the devices first.

In the Linux kernel, the following vulnerability has been resolved: iommu/arm-smmu: Don't unregister on shutdown Michael Walle says he noticed the following stack trace while performing a shutdown with "reboot -f". He suggests he got "lucky" and just hit the correct spot for the reboot while there was a packet transmission in flight. Unable to handle kernel NULL pointer dereference at virtual address 0000000000000098 CPU: 0 PID: 23 Comm: kworker/0:1 Not tainted 6.1.0-rc5-00088-gf3600ff8e322 #1930 Hardware name: Kontron KBox A-230-LS (DT) pc : iommu_get_dma_domain+0x14/0x20 lr : iommu_dma_map_page+0x9c/0x254 Call trace: iommu_get_dma_domain+0x14/0x20 dma_map_page_attrs+0x1ec/0x250 enetc_start_xmit+0x14c/0x10b0 enetc_xmit+0x60/0xdc dev_hard_start_xmit+0xb8/0x210 sch_direct_xmit+0x11c/0x420 __dev_queue_xmit+0x354/0xb20 ip6_finish_output2+0x280/0x5b0 __ip6_finish_output+0x15c/0x270 ip6_output+0x78/0x15c NF_HOOK.constprop.0+0x50/0xd0 mld_sendpack+0x1bc/0x320 mld_ifc_work+0x1d8/0x4dc process_one_work+0x1e8/0x460 worker_thread+0x178/0x534 kthread+0xe0/0xe4 ret_from_fork+0x10/0x20 Code: d503201f f9416800 d503233f d50323bf (f9404c00) ---[ end trace 0000000000000000 ]--- Kernel panic - not syncing: Oops: Fatal exception in interrupt This appears to be reproducible when the board has a fixed IP address, is ping flooded from another host, and "reboot -f" is used. The following is one more manifestation of the issue: $ reboot -f kvm: exiting hardware virtualization cfg80211: failed to load regulatory.db arm-smmu 5000000.iommu: disabling translation sdhci-esdhc 2140000.mmc: Removing from iommu group 11 sdhci-esdhc 2150000.mmc: Removing from iommu group 12 fsl-edma 22c0000.dma-controller: Removing from iommu group 17 dwc3 3100000.usb: Removing from iommu group 9 dwc3 3110000.usb: Removing from iommu group 10 ahci-qoriq 3200000.sata: Removing from iommu group 2 fsl-qdma 8380000.dma-controller: Removing from iommu group 20 platform f080000.display: Removing from iommu group 0 etnaviv-gpu f0c0000.gpu: Removing from iommu group 1 etnaviv etnaviv: Removing from iommu group 1 caam_jr 8010000.jr: Removing from iommu group 13 caam_jr 8020000.jr: Removing from iommu group 14 caam_jr 8030000.jr: Removing from iommu group 15 caam_jr 8040000.jr: Removing from iommu group 16 fsl_enetc 0000:00:00.0: Removing from iommu group 4 arm-smmu 5000000.iommu: Blocked unknown Stream ID 0x429; boot with "arm-smmu.disable_bypass=0" to allow, but this may have security implications arm-smmu 5000000.iommu: GFSR 0x80000002, GFSYNR0 0x00000002, GFSYNR1 0x00000429, GFSYNR2 0x00000000 fsl_enetc 0000:00:00.1: Removing from iommu group 5 arm-smmu 5000000.iommu: Blocked unknown Stream ID 0x429; boot with "arm-smmu.disable_bypass=0" to allow, but this may have security implications arm-smmu 5000000.iommu: GFSR 0x80000002, GFSYNR0 0x00000002, GFSYNR1 0x00000429, GFSYNR2 0x00000000 arm-smmu 5000000.iommu: Blocked unknown Stream ID 0x429; boot with "arm-smmu.disable_bypass=0" to allow, but this may have security implications arm-smmu 5000000.iommu: GFSR 0x80000002, GFSYNR0 0x00000000, GFSYNR1 0x00000429, GFSYNR2 0x00000000 fsl_enetc 0000:00:00.2: Removing from iommu group 6 fsl_enetc_mdio 0000:00:00.3: Removing from iommu group 8 mscc_felix 0000:00:00.5: Removing from iommu group 3 fsl_enetc 0000:00:00.6: Removing from iommu group 7 pcieport 0001:00:00.0: Removing from iommu group 18 arm-smmu 5000000.iommu: Blocked unknown Stream ID 0x429; boot with "arm-smmu.disable_bypass=0" to allow, but this may have security implications arm-smmu 5000000.iommu: GFSR 0x00000002, GFSYNR0 0x00000000, GFSYNR1 0x00000429, GFSYNR2 0x00000000 pcieport 0002:00:00.0: Removing from iommu group 19 Unable to handle kernel NULL pointer dereference at virtual address 00000000000000a8 pc : iommu_get_dma_domain+0x14/0x20 lr : iommu_dma_unmap_page+0x38/0xe0 Call trace: iommu_get_dma_domain+0x14/0x20 dma_unmap_page_attrs+0x38/0x1d0 en ---truncated---

In the Linux kernel, the following vulnerability has been resolved: s390/dasd: fix Oops in dasd_alias_get_start_dev due to missing pavgroup Fix Oops in dasd_alias_get_start_dev() function caused by the pavgroup pointer being NULL. The pavgroup pointer is checked on the entrance of the function but without the lcu->lock being held. Therefore there is a race window between dasd_alias_get_start_dev() and _lcu_update() which sets pavgroup to NULL with the lcu->lock held. Fix by checking the pavgroup pointer with lcu->lock held.

In the Linux kernel, the following vulnerability has been resolved: xen-netfront: Fix NULL sring after live migration A NAPI is setup for each network sring to poll data to kernel The sring with source host is destroyed before live migration and new sring with target host is setup after live migration. The NAPI for the old sring is not deleted until setup new sring with target host after migration. With busy_poll/busy_read enabled, the NAPI can be polled before got deleted when resume VM. BUG: unable to handle kernel NULL pointer dereference at 0000000000000008 IP: xennet_poll+0xae/0xd20 PGD 0 P4D 0 Oops: 0000 [#1] SMP PTI Call Trace: finish_task_switch+0x71/0x230 timerqueue_del+0x1d/0x40 hrtimer_try_to_cancel+0xb5/0x110 xennet_alloc_rx_buffers+0x2a0/0x2a0 napi_busy_loop+0xdb/0x270 sock_poll+0x87/0x90 do_sys_poll+0x26f/0x580 tracing_map_insert+0x1d4/0x2f0 event_hist_trigger+0x14a/0x260 finish_task_switch+0x71/0x230 __schedule+0x256/0x890 recalc_sigpending+0x1b/0x50 xen_sched_clock+0x15/0x20 __rb_reserve_next+0x12d/0x140 ring_buffer_lock_reserve+0x123/0x3d0 event_triggers_call+0x87/0xb0 trace_event_buffer_commit+0x1c4/0x210 xen_clocksource_get_cycles+0x15/0x20 ktime_get_ts64+0x51/0xf0 SyS_ppoll+0x160/0x1a0 SyS_ppoll+0x160/0x1a0 do_syscall_64+0x73/0x130 entry_SYSCALL_64_after_hwframe+0x41/0xa6 ... RIP: xennet_poll+0xae/0xd20 RSP: ffffb4f041933900 CR2: 0000000000000008 ---[ end trace f8601785b354351c ]--- xen frontend should remove the NAPIs for the old srings before live migration as the bond srings are destroyed There is a tiny window between the srings are set to NULL and the NAPIs are disabled, It is safe as the NAPI threads are still frozen at that time

In the Linux kernel, the following vulnerability has been resolved: net: phy: fix null-ptr-deref while probe() failed I got a null-ptr-deref report as following when doing fault injection test: BUG: kernel NULL pointer dereference, address: 0000000000000058 Oops: 0000 [#1] PREEMPT SMP KASAN PTI CPU: 1 PID: 253 Comm: 507-spi-dm9051 Tainted: G B N 6.1.0-rc3+ Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014 RIP: 0010:klist_put+0x2d/0xd0 Call Trace: <TASK> klist_remove+0xf1/0x1c0 device_release_driver_internal+0x23e/0x2d0 bus_remove_device+0x1bd/0x240 device_del+0x357/0x770 phy_device_remove+0x11/0x30 mdiobus_unregister+0xa5/0x140 release_nodes+0x6a/0xa0 devres_release_all+0xf8/0x150 device_unbind_cleanup+0x19/0xd0 //probe path: phy_device_register() device_add() phy_connect phy_attach_direct() //set device driver probe() //it's failed, driver is not bound device_bind_driver() // probe failed, it's not called //remove path: phy_device_remove() device_del() device_release_driver_internal() __device_release_driver() //dev->drv is not NULL klist_remove() <- knode_driver is not added yet, cause null-ptr-deref In phy_attach_direct(), after setting the 'dev->driver', probe() fails, device_bind_driver() is not called, so the knode_driver->n_klist is not set, then it causes null-ptr-deref in __device_release_driver() while deleting device. Fix this by setting dev->driver to NULL in the error path in phy_attach_direct().

In the Linux kernel, the following vulnerability has been resolved: staging: vchiq_arm: Avoid NULL ptr deref in vchiq_dump_platform_instances vchiq_get_state() can return a NULL pointer. So handle this cases and avoid a NULL pointer derefence in vchiq_dump_platform_instances.

In the Linux kernel, the following vulnerability has been resolved: ice: fix NULL pointer dereference in ice_update_vsi_tx_ring_stats() It is possible to do NULL pointer dereference in routine that updates Tx ring stats. Currently only stats and bytes are updated when ring pointer is valid, but later on ring is accessed to propagate gathered Tx stats onto VSI stats. Change the existing logic to move to next ring when ring is NULL.

In the Linux kernel, the following vulnerability has been resolved: rtc: cmos: Fix event handler registration ordering issue Because acpi_install_fixed_event_handler() enables the event automatically on success, it is incorrect to call it before the handler routine passed to it is ready to handle events. Unfortunately, the rtc-cmos driver does exactly the incorrect thing by calling cmos_wake_setup(), which passes rtc_handler() to acpi_install_fixed_event_handler(), before cmos_do_probe(), because rtc_handler() uses dev_get_drvdata() to get to the cmos object pointer and the driver data pointer is only populated in cmos_do_probe(). This leads to a NULL pointer dereference in rtc_handler() on boot if the RTC fixed event happens to be active at the init time. To address this issue, change the initialization ordering of the driver so that cmos_wake_setup() is always called after a successful cmos_do_probe() call. While at it, change cmos_pnp_probe() to call cmos_do_probe() after the initial if () statement used for computing the IRQ argument to be passed to cmos_do_probe() which is cleaner than calling it in each branch of that if () (local variable "irq" can be of type int, because it is passed to that function as an argument of type int). Note that commit 6492fed7d8c9 ("rtc: rtc-cmos: Do not check ACPI_FADT_LOW_POWER_S0") caused this issue to affect a larger number of systems, because previously it only affected systems with ACPI_FADT_LOW_POWER_S0 set, but it is present regardless of that commit.

In telephony service, there is a possible missing permission check. This could lead to local denial of service with no additional execution privileges.

In the Linux kernel, the following vulnerability has been resolved: io_uring: Fix a null-ptr-deref in io_tctx_exit_cb() Syzkaller reports a NULL deref bug as follows: BUG: KASAN: null-ptr-deref in io_tctx_exit_cb+0x53/0xd3 Read of size 4 at addr 0000000000000138 by task file1/1955 CPU: 1 PID: 1955 Comm: file1 Not tainted 6.1.0-rc7-00103-gef4d3ea40565 #75 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.el7 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0xcd/0x134 ? io_tctx_exit_cb+0x53/0xd3 kasan_report+0xbb/0x1f0 ? io_tctx_exit_cb+0x53/0xd3 kasan_check_range+0x140/0x190 io_tctx_exit_cb+0x53/0xd3 task_work_run+0x164/0x250 ? task_work_cancel+0x30/0x30 get_signal+0x1c3/0x2440 ? lock_downgrade+0x6e0/0x6e0 ? lock_downgrade+0x6e0/0x6e0 ? exit_signals+0x8b0/0x8b0 ? do_raw_read_unlock+0x3b/0x70 ? do_raw_spin_unlock+0x50/0x230 arch_do_signal_or_restart+0x82/0x2470 ? kmem_cache_free+0x260/0x4b0 ? putname+0xfe/0x140 ? get_sigframe_size+0x10/0x10 ? do_execveat_common.isra.0+0x226/0x710 ? lockdep_hardirqs_on+0x79/0x100 ? putname+0xfe/0x140 ? do_execveat_common.isra.0+0x238/0x710 exit_to_user_mode_prepare+0x15f/0x250 syscall_exit_to_user_mode+0x19/0x50 do_syscall_64+0x42/0xb0 entry_SYSCALL_64_after_hwframe+0x63/0xcd RIP: 0023:0x0 Code: Unable to access opcode bytes at 0xffffffffffffffd6. RSP: 002b:00000000fffb7790 EFLAGS: 00000200 ORIG_RAX: 000000000000000b RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 </TASK> Kernel panic - not syncing: panic_on_warn set ... This happens because the adding of task_work from io_ring_exit_work() isn't synchronized with canceling all work items from eg exec. The execution of the two are ordered in that they are both run by the task itself, but if io_tctx_exit_cb() is queued while we're canceling all work items off exec AND gets executed when the task exits to userspace rather than in the main loop in io_uring_cancel_generic(), then we can find current->io_uring == NULL and hit the above crash. It's safe to add this NULL check here, because the execution of the two paths are done by the task itself. [axboe: add code comment and also put an explanation in the commit msg]

In the Linux kernel, the following vulnerability has been resolved: can: slcan: fix freed work crash The LTP test pty03 is causing a crash in slcan: BUG: kernel NULL pointer dereference, address: 0000000000000008 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 0 PID: 348 Comm: kworker/0:3 Not tainted 6.0.8-1-default #1 openSUSE Tumbleweed 9d20364b934f5aab0a9bdf84e8f45cfdfae39dab Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.15.0-0-g2dd4b9b-rebuilt.opensuse.org 04/01/2014 Workqueue: 0x0 (events) RIP: 0010:process_one_work (/home/rich/kernel/linux/kernel/workqueue.c:706 /home/rich/kernel/linux/kernel/workqueue.c:2185) Code: 49 89 ff 41 56 41 55 41 54 55 53 48 89 f3 48 83 ec 10 48 8b 06 48 8b 6f 48 49 89 c4 45 30 e4 a8 04 b8 00 00 00 00 4c 0f 44 e0 <49> 8b 44 24 08 44 8b a8 00 01 00 00 41 83 e5 20 f6 45 10 04 75 0e RSP: 0018:ffffaf7b40f47e98 EFLAGS: 00010046 RAX: 0000000000000000 RBX: ffff9d644e1b8b48 RCX: ffff9d649e439968 RDX: 00000000ffff8455 RSI: ffff9d644e1b8b48 RDI: ffff9d64764aa6c0 RBP: ffff9d649e4335c0 R08: 0000000000000c00 R09: ffff9d64764aa734 R10: 0000000000000007 R11: 0000000000000001 R12: 0000000000000000 R13: ffff9d649e4335e8 R14: ffff9d64490da780 R15: ffff9d64764aa6c0 FS: 0000000000000000(0000) GS:ffff9d649e400000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000008 CR3: 0000000036424000 CR4: 00000000000006f0 Call Trace: <TASK> worker_thread (/home/rich/kernel/linux/kernel/workqueue.c:2436) kthread (/home/rich/kernel/linux/kernel/kthread.c:376) ret_from_fork (/home/rich/kernel/linux/arch/x86/entry/entry_64.S:312) Apparently, the slcan's tx_work is freed while being scheduled. While slcan_netdev_close() (netdev side) calls flush_work(&sl->tx_work), slcan_close() (tty side) does not. So when the netdev is never set UP, but the tty is stuffed with bytes and forced to wakeup write, the work is scheduled, but never flushed. So add an additional flush_work() to slcan_close() to be sure the work is flushed under all circumstances. The Fixes commit below moved flush_work() from slcan_close() to slcan_netdev_close(). What was the rationale behind it? Maybe we can drop the one in slcan_netdev_close()? I see the same pattern in can327. So it perhaps needs the very same fix.

In the Linux kernel, the following vulnerability has been resolved: net/smc: Fix NULL pointer dereference in smc_pnet_find_ib() dev_name() was called with dev.parent as argument but without to NULL-check it before. Solve this by checking the pointer before the call to dev_name().

In the Linux kernel, the following vulnerability has been resolved: drm/panel: ili9341: fix optional regulator handling If the optional regulator lookup fails, reset the pointer to NULL. Other functions such as mipi_dbi_poweron_reset_conditional() only do a NULL pointer check and will otherwise dereference the error pointer.

In the Linux kernel, the following vulnerability has been resolved: drm: mxsfb: Fix NULL pointer dereference mxsfb should not ever dereference the NULL pointer which drm_atomic_get_new_bridge_state is allowed to return. Assume a fixed format instead.

In the Linux kernel, the following vulnerability has been resolved: media: lgdt3306a: Add a check against null-pointer-def The driver should check whether the client provides the platform_data. The following log reveals it: [ 29.610324] BUG: KASAN: null-ptr-deref in kmemdup+0x30/0x40 [ 29.610730] Read of size 40 at addr 0000000000000000 by task bash/414 [ 29.612820] Call Trace: [ 29.613030] <TASK> [ 29.613201] dump_stack_lvl+0x56/0x6f [ 29.613496] ? kmemdup+0x30/0x40 [ 29.613754] print_report.cold+0x494/0x6b7 [ 29.614082] ? kmemdup+0x30/0x40 [ 29.614340] kasan_report+0x8a/0x190 [ 29.614628] ? kmemdup+0x30/0x40 [ 29.614888] kasan_check_range+0x14d/0x1d0 [ 29.615213] memcpy+0x20/0x60 [ 29.615454] kmemdup+0x30/0x40 [ 29.615700] lgdt3306a_probe+0x52/0x310 [ 29.616339] i2c_device_probe+0x951/0xa90

In the Linux kernel, the following vulnerability has been resolved: net: ethernet: nixge: fix NULL dereference In function nixge_hw_dma_bd_release() dereference of NULL pointer priv->rx_bd_v is possible for the case of its allocation failure in nixge_hw_dma_bd_init(). Move for() loop with priv->rx_bd_v dereference under the check for its validity. Found by Linux Verification Center (linuxtesting.org) with SVACE.

A flaw NULL Pointer Dereference in the Linux kernel NTFS3 driver function attr_punch_hole() was found. A local user could use this flaw to crash the system.

In the Linux kernel, the following vulnerability has been resolved: crypto: af_alg - get rid of alg_memory_allocated alg_memory_allocated does not seem to be really used. alg_proto does have a .memory_allocated field, but no corresponding .sysctl_mem. This means sk_has_account() returns true, but all sk_prot_mem_limits() users will trigger a NULL dereference [1]. THis was not a problem until SO_RESERVE_MEM addition. general protection fault, probably for non-canonical address 0xdffffc0000000001: 0000 [#1] PREEMPT SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f] CPU: 1 PID: 3591 Comm: syz-executor153 Not tainted 5.17.0-rc3-syzkaller-00316-gb81b1829e7e3 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:sk_prot_mem_limits include/net/sock.h:1523 [inline] RIP: 0010:sock_reserve_memory+0x1d7/0x330 net/core/sock.c:1000 Code: 08 00 74 08 48 89 ef e8 27 20 bb f9 4c 03 7c 24 10 48 8b 6d 00 48 83 c5 08 48 89 e8 48 c1 e8 03 48 b9 00 00 00 00 00 fc ff df <80> 3c 08 00 74 08 48 89 ef e8 fb 1f bb f9 48 8b 6d 00 4c 89 ff 48 RSP: 0018:ffffc90001f1fb68 EFLAGS: 00010202 RAX: 0000000000000001 RBX: ffff88814aabc000 RCX: dffffc0000000000 RDX: 0000000000000001 RSI: 0000000000000008 RDI: ffffffff90e18120 RBP: 0000000000000008 R08: dffffc0000000000 R09: fffffbfff21c3025 R10: fffffbfff21c3025 R11: 0000000000000000 R12: ffffffff8d109840 R13: 0000000000001002 R14: 0000000000000001 R15: 0000000000000001 FS: 0000555556e08300(0000) GS:ffff8880b9b00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc74416f130 CR3: 0000000073d9e000 CR4: 00000000003506e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> sock_setsockopt+0x14a9/0x3a30 net/core/sock.c:1446 __sys_setsockopt+0x5af/0x980 net/socket.c:2176 __do_sys_setsockopt net/socket.c:2191 [inline] __se_sys_setsockopt net/socket.c:2188 [inline] __x64_sys_setsockopt+0xb1/0xc0 net/socket.c:2188 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7fc7440fddc9 Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 51 15 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007ffe98f07968 EFLAGS: 00000246 ORIG_RAX: 0000000000000036 RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007fc7440fddc9 RDX: 0000000000000049 RSI: 0000000000000001 RDI: 0000000000000004 RBP: 0000000000000000 R08: 0000000000000004 R09: 00007ffe98f07990 R10: 0000000020000000 R11: 0000000000000246 R12: 00007ffe98f0798c R13: 00007ffe98f079a0 R14: 00007ffe98f079e0 R15: 0000000000000000 </TASK> Modules linked in: ---[ end trace 0000000000000000 ]--- RIP: 0010:sk_prot_mem_limits include/net/sock.h:1523 [inline] RIP: 0010:sock_reserve_memory+0x1d7/0x330 net/core/sock.c:1000 Code: 08 00 74 08 48 89 ef e8 27 20 bb f9 4c 03 7c 24 10 48 8b 6d 00 48 83 c5 08 48 89 e8 48 c1 e8 03 48 b9 00 00 00 00 00 fc ff df <80> 3c 08 00 74 08 48 89 ef e8 fb 1f bb f9 48 8b 6d 00 4c 89 ff 48 RSP: 0018:ffffc90001f1fb68 EFLAGS: 00010202 RAX: 0000000000000001 RBX: ffff88814aabc000 RCX: dffffc0000000000 RDX: 0000000000000001 RSI: 0000000000000008 RDI: ffffffff90e18120 RBP: 0000000000000008 R08: dffffc0000000000 R09: fffffbfff21c3025 R10: fffffbfff21c3025 R11: 0000000000000000 R12: ffffffff8d109840 R13: 0000000000001002 R14: 0000000000000001 R15: 0000000000000001 FS: 0000555556e08300(0000) GS:ffff8880b9b00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc74416f130 CR3: 0000000073d9e000 CR4: 00000000003506e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000

In the Linux kernel, the following vulnerability has been resolved: net: arcnet: com20020: Fix null-ptr-deref in com20020pci_probe() During driver initialization, the pointer of card info, i.e. the variable 'ci' is required. However, the definition of 'com20020pci_id_table' reveals that this field is empty for some devices, which will cause null pointer dereference when initializing these devices. The following log reveals it: [ 3.973806] KASAN: null-ptr-deref in range [0x0000000000000028-0x000000000000002f] [ 3.973819] RIP: 0010:com20020pci_probe+0x18d/0x13e0 [com20020_pci] [ 3.975181] Call Trace: [ 3.976208] local_pci_probe+0x13f/0x210 [ 3.977248] pci_device_probe+0x34c/0x6d0 [ 3.977255] ? pci_uevent+0x470/0x470 [ 3.978265] really_probe+0x24c/0x8d0 [ 3.978273] __driver_probe_device+0x1b3/0x280 [ 3.979288] driver_probe_device+0x50/0x370 Fix this by checking whether the 'ci' is a null pointer first.

In the Linux kernel, the following vulnerability has been resolved: hwmon: Handle failure to register sensor with thermal zone correctly If an attempt is made to a sensor with a thermal zone and it fails, the call to devm_thermal_zone_of_sensor_register() may return -ENODEV. This may result in crashes similar to the following. Unable to handle kernel NULL pointer dereference at virtual address 00000000000003cd ... Internal error: Oops: 96000021 [#1] PREEMPT SMP ... pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : mutex_lock+0x18/0x60 lr : thermal_zone_device_update+0x40/0x2e0 sp : ffff800014c4fc60 x29: ffff800014c4fc60 x28: ffff365ee3f6e000 x27: ffffdde218426790 x26: ffff365ee3f6e000 x25: 0000000000000000 x24: ffff365ee3f6e000 x23: ffffdde218426870 x22: ffff365ee3f6e000 x21: 00000000000003cd x20: ffff365ee8bf3308 x19: ffffffffffffffed x18: 0000000000000000 x17: ffffdde21842689c x16: ffffdde1cb7a0b7c x15: 0000000000000040 x14: ffffdde21a4889a0 x13: 0000000000000228 x12: 0000000000000000 x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000 x8 : 0000000001120000 x7 : 0000000000000001 x6 : 0000000000000000 x5 : 0068000878e20f07 x4 : 0000000000000000 x3 : 00000000000003cd x2 : ffff365ee3f6e000 x1 : 0000000000000000 x0 : 00000000000003cd Call trace: mutex_lock+0x18/0x60 hwmon_notify_event+0xfc/0x110 0xffffdde1cb7a0a90 0xffffdde1cb7a0b7c irq_thread_fn+0x2c/0xa0 irq_thread+0x134/0x240 kthread+0x178/0x190 ret_from_fork+0x10/0x20 Code: d503201f d503201f d2800001 aa0103e4 (c8e47c02) Jon Hunter reports that the exact call sequence is: hwmon_notify_event() --> hwmon_thermal_notify() --> thermal_zone_device_update() --> update_temperature() --> mutex_lock() The hwmon core needs to handle all errors returned from calls to devm_thermal_zone_of_sensor_register(). If the call fails with -ENODEV, report that the sensor was not attached to a thermal zone but continue to register the hwmon device.

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: sdata can be NULL during AMPDU start ieee80211_tx_ba_session_handle_start() may get NULL for sdata when a deauthentication is ongoing. Here a trace triggering the race with the hostapd test multi_ap_fronthaul_on_ap: (gdb) list *drv_ampdu_action+0x46 0x8b16 is in drv_ampdu_action (net/mac80211/driver-ops.c:396). 391 int ret = -EOPNOTSUPP; 392 393 might_sleep(); 394 395 sdata = get_bss_sdata(sdata); 396 if (!check_sdata_in_driver(sdata)) 397 return -EIO; 398 399 trace_drv_ampdu_action(local, sdata, params); 400 wlan0: moving STA 02:00:00:00:03:00 to state 3 wlan0: associated wlan0: deauthenticating from 02:00:00:00:03:00 by local choice (Reason: 3=DEAUTH_LEAVING) wlan3.sta1: Open BA session requested for 02:00:00:00:00:00 tid 0 wlan3.sta1: dropped frame to 02:00:00:00:00:00 (unauthorized port) wlan0: moving STA 02:00:00:00:03:00 to state 2 wlan0: moving STA 02:00:00:00:03:00 to state 1 wlan0: Removed STA 02:00:00:00:03:00 wlan0: Destroyed STA 02:00:00:00:03:00 BUG: unable to handle page fault for address: fffffffffffffb48 PGD 11814067 P4D 11814067 PUD 11816067 PMD 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 2 PID: 133397 Comm: kworker/u16:1 Tainted: G W 6.1.0-rc8-wt+ #59 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.0-20220807_005459-localhost 04/01/2014 Workqueue: phy3 ieee80211_ba_session_work [mac80211] RIP: 0010:drv_ampdu_action+0x46/0x280 [mac80211] Code: 53 48 89 f3 be 89 01 00 00 e8 d6 43 bf ef e8 21 46 81 f0 83 bb a0 1b 00 00 04 75 0e 48 8b 9b 28 0d 00 00 48 81 eb 10 0e 00 00 <8b> 93 58 09 00 00 f6 c2 20 0f 84 3b 01 00 00 8b 05 dd 1c 0f 00 85 RSP: 0018:ffffc900025ebd20 EFLAGS: 00010287 RAX: 0000000000000000 RBX: fffffffffffff1f0 RCX: ffff888102228240 RDX: 0000000080000000 RSI: ffffffff918c5de0 RDI: ffff888102228b40 RBP: ffffc900025ebd40 R08: 0000000000000001 R09: 0000000000000001 R10: 0000000000000001 R11: 0000000000000000 R12: ffff888118c18ec0 R13: 0000000000000000 R14: ffffc900025ebd60 R15: ffff888018b7efb8 FS: 0000000000000000(0000) GS:ffff88817a600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: fffffffffffffb48 CR3: 0000000105228006 CR4: 0000000000170ee0 Call Trace: <TASK> ieee80211_tx_ba_session_handle_start+0xd0/0x190 [mac80211] ieee80211_ba_session_work+0xff/0x2e0 [mac80211] process_one_work+0x29f/0x620 worker_thread+0x4d/0x3d0 ? process_one_work+0x620/0x620 kthread+0xfb/0x120 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork+0x22/0x30 </TASK>

In the Linux kernel, the following vulnerability has been resolved: tty: fix possible null-ptr-defer in spk_ttyio_release Run the following tests on the qemu platform: syzkaller:~# modprobe speakup_audptr input: Speakup as /devices/virtual/input/input4 initialized device: /dev/synth, node (MAJOR 10, MINOR 125) speakup 3.1.6: initialized synth name on entry is: (null) synth probe spk_ttyio_initialise_ldisc failed because tty_kopen_exclusive returned failed (errno -16), then remove the module, we will get a null-ptr-defer problem, as follow: syzkaller:~# modprobe -r speakup_audptr releasing synth audptr BUG: kernel NULL pointer dereference, address: 0000000000000080 #PF: supervisor write access in kernel mode #PF: error_code(0x0002) - not-present page PGD 0 P4D 0 Oops: 0002 [#1] PREEMPT SMP PTI CPU: 2 PID: 204 Comm: modprobe Not tainted 6.1.0-rc6-dirty #1 RIP: 0010:mutex_lock+0x14/0x30 Call Trace: <TASK> spk_ttyio_release+0x19/0x70 [speakup] synth_release.part.6+0xac/0xc0 [speakup] synth_remove+0x56/0x60 [speakup] __x64_sys_delete_module+0x156/0x250 ? fpregs_assert_state_consistent+0x1d/0x50 do_syscall_64+0x37/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd </TASK> Modules linked in: speakup_audptr(-) speakup Dumping ftrace buffer: in_synth->dev was not initialized during modprobe, so we add check for in_synth->dev to fix this bug.

In the Linux kernel, the following vulnerability has been resolved: net: sfc: add missing xdp queue reinitialization After rx/tx ring buffer size is changed, kernel panic occurs when it acts XDP_TX or XDP_REDIRECT. When tx/rx ring buffer size is changed(ethtool -G), sfc driver reallocates and reinitializes rx and tx queues and their buffer (tx_queue->buffer). But it misses reinitializing xdp queues(efx->xdp_tx_queues). So, while it is acting XDP_TX or XDP_REDIRECT, it uses the uninitialized tx_queue->buffer. A new function efx_set_xdp_channels() is separated from efx_set_channels() to handle only xdp queues. Splat looks like: BUG: kernel NULL pointer dereference, address: 000000000000002a #PF: supervisor write access in kernel mode #PF: error_code(0x0002) - not-present page PGD 0 P4D 0 Oops: 0002 [#4] PREEMPT SMP NOPTI RIP: 0010:efx_tx_map_chunk+0x54/0x90 [sfc] CPU: 2 PID: 0 Comm: swapper/2 Tainted: G D 5.17.0+ #55 e8beeee8289528f11357029357cf Code: 48 8b 8d a8 01 00 00 48 8d 14 52 4c 8d 2c d0 44 89 e0 48 85 c9 74 0e 44 89 e2 4c 89 f6 48 80 RSP: 0018:ffff92f121e45c60 EFLAGS: 00010297 RIP: 0010:efx_tx_map_chunk+0x54/0x90 [sfc] RAX: 0000000000000040 RBX: ffff92ea506895c0 RCX: ffffffffc0330870 RDX: 0000000000000001 RSI: 00000001139b10ce RDI: ffff92ea506895c0 RBP: ffffffffc0358a80 R08: 00000001139b110d R09: 0000000000000000 R10: 0000000000000001 R11: ffff92ea414c0088 R12: 0000000000000040 R13: 0000000000000018 R14: 00000001139b10ce R15: ffff92ea506895c0 FS: 0000000000000000(0000) GS:ffff92f121ec0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 Code: 48 8b 8d a8 01 00 00 48 8d 14 52 4c 8d 2c d0 44 89 e0 48 85 c9 74 0e 44 89 e2 4c 89 f6 48 80 CR2: 000000000000002a CR3: 00000003e6810004 CR4: 00000000007706e0 RSP: 0018:ffff92f121e85c60 EFLAGS: 00010297 PKRU: 55555554 RAX: 0000000000000040 RBX: ffff92ea50689700 RCX: ffffffffc0330870 RDX: 0000000000000001 RSI: 00000001145a90ce RDI: ffff92ea50689700 RBP: ffffffffc0358a80 R08: 00000001145a910d R09: 0000000000000000 R10: 0000000000000001 R11: ffff92ea414c0088 R12: 0000000000000040 R13: 0000000000000018 R14: 00000001145a90ce R15: ffff92ea50689700 FS: 0000000000000000(0000) GS:ffff92f121e80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000000000002a CR3: 00000003e6810005 CR4: 00000000007706e0 PKRU: 55555554 Call Trace: <IRQ> efx_xdp_tx_buffers+0x12b/0x3d0 [sfc 84c94b8e32d44d296c17e10a634d3ad454de4ba5] __efx_rx_packet+0x5c3/0x930 [sfc 84c94b8e32d44d296c17e10a634d3ad454de4ba5] efx_rx_packet+0x28c/0x2e0 [sfc 84c94b8e32d44d296c17e10a634d3ad454de4ba5] efx_ef10_ev_process+0x5f8/0xf40 [sfc 84c94b8e32d44d296c17e10a634d3ad454de4ba5] ? enqueue_task_fair+0x95/0x550 efx_poll+0xc4/0x360 [sfc 84c94b8e32d44d296c17e10a634d3ad454de4ba5]

In the Linux kernel, the following vulnerability has been resolved: net: ethernet: stmmac: fix altr_tse_pcs function when using a fixed-link When using a fixed-link, the altr_tse_pcs driver crashes due to null-pointer dereference as no phy_device is provided to tse_pcs_fix_mac_speed function. Fix this by adding a check for phy_dev before calling the tse_pcs_fix_mac_speed() function. Also clean up the tse_pcs_fix_mac_speed function a bit. There is no need to check for splitter_base and sgmii_adapter_base because the driver will fail if these 2 variables are not derived from the device tree.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix macsec possible null dereference when updating MAC security entity (SecY) Upon updating MAC security entity (SecY) in hw offload path, the macsec security association (SA) initialization routine is called. In case of extended packet number (epn) is enabled the salt and ssci attributes are retrieved using the MACsec driver rx_sa context which is unavailable when updating a SecY property such as encoding-sa hence the null dereference. Fix by using the provided SA to set those attributes.