In the Linux kernel, the following vulnerability has been resolved: net: bridge: switchdev: Skip MDB replays of deferred events on offload Before this change, generation of the list of MDB events to replay would race against the creation of new group memberships, either from the IGMP/MLD snooping logic or from user configuration. While new memberships are immediately visible to walkers of br->mdb_list, the notification of their existence to switchdev event subscribers is deferred until a later point in time. So if a replay list was generated during a time that overlapped with such a window, it would also contain a replay of the not-yet-delivered event. The driver would thus receive two copies of what the bridge internally considered to be one single event. On destruction of the bridge, only a single membership deletion event was therefore sent. As a consequence of this, drivers which reference count memberships (at least DSA), would be left with orphan groups in their hardware database when the bridge was destroyed. This is only an issue when replaying additions. While deletion events may still be pending on the deferred queue, they will already have been removed from br->mdb_list, so no duplicates can be generated in that scenario. To a user this meant that old group memberships, from a bridge in which a port was previously attached, could be reanimated (in hardware) when the port joined a new bridge, without the new bridge's knowledge. For example, on an mv88e6xxx system, create a snooping bridge and immediately add a port to it: root@infix-06-0b-00:~$ ip link add dev br0 up type bridge mcast_snooping 1 && \ > ip link set dev x3 up master br0 And then destroy the bridge: root@infix-06-0b-00:~$ ip link del dev br0 root@infix-06-0b-00:~$ mvls atu ADDRESS FID STATE Q F 0 1 2 3 4 5 6 7 8 9 a DEV:0 Marvell 88E6393X 33:33:00:00:00:6a 1 static - - 0 . . . . . . . . . . 33:33:ff:87:e4:3f 1 static - - 0 . . . . . . . . . . ff:ff:ff:ff:ff:ff 1 static - - 0 1 2 3 4 5 6 7 8 9 a root@infix-06-0b-00:~$ The two IPv6 groups remain in the hardware database because the port (x3) is notified of the host's membership twice: once via the original event and once via a replay. Since only a single delete notification is sent, the count remains at 1 when the bridge is destroyed. Then add the same port (or another port belonging to the same hardware domain) to a new bridge, this time with snooping disabled: root@infix-06-0b-00:~$ ip link add dev br1 up type bridge mcast_snooping 0 && \ > ip link set dev x3 up master br1 All multicast, including the two IPv6 groups from br0, should now be flooded, according to the policy of br1. But instead the old memberships are still active in the hardware database, causing the switch to only forward traffic to those groups towards the CPU (port 0). Eliminate the race in two steps: 1. Grab the write-side lock of the MDB while generating the replay list. This prevents new memberships from showing up while we are generating the replay list. But it leaves the scenario in which a deferred event was already generated, but not delivered, before we grabbed the lock. Therefore: 2. Make sure that no deferred version of a replay event is already enqueued to the switchdev deferred queue, before adding it to the replay list, when replaying additions.

In the Linux kernel, the following vulnerability has been resolved: fsnotify: clear PARENT_WATCHED flags lazily In some setups directories can have many (usually negative) dentries. Hence __fsnotify_update_child_dentry_flags() function can take a significant amount of time. Since the bulk of this function happens under inode->i_lock this causes a significant contention on the lock when we remove the watch from the directory as the __fsnotify_update_child_dentry_flags() call from fsnotify_recalc_mask() races with __fsnotify_update_child_dentry_flags() calls from __fsnotify_parent() happening on children. This can lead upto softlockup reports reported by users. Fix the problem by calling fsnotify_update_children_dentry_flags() to set PARENT_WATCHED flags only when parent starts watching children. When parent stops watching children, clear false positive PARENT_WATCHED flags lazily in __fsnotify_parent() for each accessed child.

Race condition in the tty_fasync function in drivers/char/tty_io.c in the Linux kernel before 2.6.32.6 allows local users to cause a denial of service (NULL pointer dereference and system crash) or possibly have unspecified other impact via unknown vectors, related to the put_tty_queue and __f_setown functions. NOTE: the vulnerability was addressed in a different way in 2.6.32.9.

Race condition in some Intel(R) Aptio* V UEFI Firmware Integrator Tools may allow an authenticated user to potentially enable denial of service via local access.

A race problem was found in fs/proc/task_mmu.c in the memory management sub-component in the Linux kernel. This issue may allow a local attacker with user privilege to cause a denial of service.

In the Linux kernel, the following vulnerability has been resolved: sysctl: Fix data races in proc_douintvec(). A sysctl variable is accessed concurrently, and there is always a chance of data-race. So, all readers and writers need some basic protection to avoid load/store-tearing. This patch changes proc_douintvec() to use READ_ONCE() and WRITE_ONCE() internally to fix data-races on the sysctl side. For now, proc_douintvec() itself is tolerant to a data-race, but we still need to add annotations on the other subsystem's side.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix a data-race around sysctl_tcp_notsent_lowat. While reading sysctl_tcp_notsent_lowat, it can be changed concurrently. Thus, we need to add READ_ONCE() to its reader.

In the Linux kernel, the following vulnerability has been resolved: sysctl: Fix data races in proc_douintvec_minmax(). A sysctl variable is accessed concurrently, and there is always a chance of data-race. So, all readers and writers need some basic protection to avoid load/store-tearing. This patch changes proc_douintvec_minmax() to use READ_ONCE() and WRITE_ONCE() internally to fix data-races on the sysctl side. For now, proc_douintvec_minmax() itself is tolerant to a data-race, but we still need to add annotations on the other subsystem's side.

In the Linux kernel, the following vulnerability has been resolved: icmp: Fix a data-race around sysctl_icmp_errors_use_inbound_ifaddr. While reading sysctl_icmp_errors_use_inbound_ifaddr, it can be changed concurrently. Thus, we need to add READ_ONCE() to its reader.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix a data-race around sysctl_tcp_thin_linear_timeouts. While reading sysctl_tcp_thin_linear_timeouts, it can be changed concurrently. Thus, we need to add READ_ONCE() to its reader.

In the Linux kernel, the following vulnerability has been resolved: ipv4: Fix a data-race around sysctl_fib_sync_mem. While reading sysctl_fib_sync_mem, it can be changed concurrently. So, we need to add READ_ONCE() to avoid a data-race.

In the Linux kernel, the following vulnerability has been resolved: cipso: Fix data-races around sysctl. While reading cipso sysctl variables, they can be changed concurrently. So, we need to add READ_ONCE() to avoid data-races.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix data-races around sysctl_tcp_min_snd_mss. While reading sysctl_tcp_min_snd_mss, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: igmp: Fix data-races around sysctl_igmp_llm_reports. While reading sysctl_igmp_llm_reports, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers. This test can be packed into a helper, so such changes will be in the follow-up series after net is merged into net-next. if (ipv4_is_local_multicast(pmc->multiaddr) && !READ_ONCE(net->ipv4.sysctl_igmp_llm_reports))

In the Linux kernel, the following vulnerability has been resolved: udp: Fix a data-race around sysctl_udp_l3mdev_accept. While reading sysctl_udp_l3mdev_accept, it can be changed concurrently. Thus, we need to add READ_ONCE() to its reader.

In the Linux kernel, the following vulnerability has been resolved: tcp/dccp: Fix a data-race around sysctl_tcp_fwmark_accept. While reading sysctl_tcp_fwmark_accept, it can be changed concurrently. Thus, we need to add READ_ONCE() to its reader.

In the Linux kernel, the following vulnerability has been resolved: ipv4: Fix a data-race around sysctl_fib_multipath_use_neigh. While reading sysctl_fib_multipath_use_neigh, it can be changed concurrently. Thus, we need to add READ_ONCE() to its reader.

In the Linux kernel, the following vulnerability has been resolved: ip: Fix data-races around sysctl_ip_fwd_update_priority. While reading sysctl_ip_fwd_update_priority, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: nexthop: Fix data-races around nexthop_compat_mode. While reading nexthop_compat_mode, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix data-races around sysctl_tcp_fastopen_blackhole_timeout. While reading sysctl_tcp_fastopen_blackhole_timeout, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: sysctl: Fix data-races in proc_dou8vec_minmax(). A sysctl variable is accessed concurrently, and there is always a chance of data-race. So, all readers and writers need some basic protection to avoid load/store-tearing. This patch changes proc_dou8vec_minmax() to use READ_ONCE() and WRITE_ONCE() internally to fix data-races on the sysctl side. For now, proc_dou8vec_minmax() itself is tolerant to a data-race, but we still need to add annotations on the other subsystem's side.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix data-races around sysctl_tcp_max_reordering. While reading sysctl_tcp_max_reordering, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: raw: Fix a data-race around sysctl_raw_l3mdev_accept. While reading sysctl_raw_l3mdev_accept, it can be changed concurrently. Thus, we need to add READ_ONCE() to its reader.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix data-races around sysctl_tcp_l3mdev_accept. While reading sysctl_tcp_l3mdev_accept, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: ipv4: Fix data-races around sysctl_fib_multipath_hash_fields. While reading sysctl_fib_multipath_hash_fields, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix data-races around sysctl_tcp_recovery. While reading sysctl_tcp_recovery, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: ip: Fix a data-race around sysctl_ip_autobind_reuse. While reading sysctl_ip_autobind_reuse, it can be changed concurrently. Thus, we need to add READ_ONCE() to its reader.

In the Linux kernel, the following vulnerability has been resolved: ip: Fix data-races around sysctl_ip_fwd_use_pmtu. While reading sysctl_ip_fwd_use_pmtu, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: ip: Fix a data-race around sysctl_fwmark_reflect. While reading sysctl_fwmark_reflect, it can be changed concurrently. Thus, we need to add READ_ONCE() to its reader.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix a data-race around sysctl_tcp_mtu_probe_floor. While reading sysctl_tcp_mtu_probe_floor, it can be changed concurrently. Thus, we need to add READ_ONCE() to its reader.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix data-races around sysctl_tcp_base_mss. While reading sysctl_tcp_base_mss, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: ipv4: Fix data-races around sysctl_fib_multipath_hash_policy. While reading sysctl_fib_multipath_hash_policy, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix a data-race around sysctl_tcp_probe_interval. While reading sysctl_tcp_probe_interval, it can be changed concurrently. Thus, we need to add READ_ONCE() to its reader.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix data-races around sysctl_tcp_migrate_req. While reading sysctl_tcp_migrate_req, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix data-races around sysctl_tcp_slow_start_after_idle. While reading sysctl_tcp_slow_start_after_idle, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: icmp: Fix data-races around sysctl. While reading icmp sysctl variables, they can be changed concurrently. So, we need to add READ_ONCE() to avoid data-races.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix a data-race around sysctl_tcp_probe_threshold. While reading sysctl_tcp_probe_threshold, it can be changed concurrently. Thus, we need to add READ_ONCE() to its reader.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix a data-race around sysctl_tcp_ecn_fallback. While reading sysctl_tcp_ecn_fallback, it can be changed concurrently. Thus, we need to add READ_ONCE() to its reader.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix data-races around sysctl_tcp_fastopen. While reading sysctl_tcp_fastopen, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_tables: netlink notifier might race to release objects commit release path is invoked via call_rcu and it runs lockless to release the objects after rcu grace period. The netlink notifier handler might win race to remove objects that the transaction context is still referencing from the commit release path. Call rcu_barrier() to ensure pending rcu callbacks run to completion if the list of transactions to be destroyed is not empty.

In the Linux kernel, the following vulnerability has been resolved: vfs: fix race between evice_inodes() and find_inode()&iput() Hi, all Recently I noticed a bug[1] in btrfs, after digged it into and I believe it'a race in vfs. Let's assume there's a inode (ie ino 261) with i_count 1 is called by iput(), and there's a concurrent thread calling generic_shutdown_super(). cpu0: cpu1: iput() // i_count is 1 ->spin_lock(inode) ->dec i_count to 0 ->iput_final() generic_shutdown_super() ->__inode_add_lru() ->evict_inodes() // cause some reason[2] ->if (atomic_read(inode->i_count)) continue; // return before // inode 261 passed the above check // list_lru_add_obj() // and then schedule out ->spin_unlock() // note here: the inode 261 // was still at sb list and hash list, // and I_FREEING|I_WILL_FREE was not been set btrfs_iget() // after some function calls ->find_inode() // found the above inode 261 ->spin_lock(inode) // check I_FREEING|I_WILL_FREE // and passed ->__iget() ->spin_unlock(inode) // schedule back ->spin_lock(inode) // check (I_NEW|I_FREEING|I_WILL_FREE) flags, // passed and set I_FREEING iput() ->spin_unlock(inode) ->spin_lock(inode) ->evict() // dec i_count to 0 ->iput_final() ->spin_unlock() ->evict() Now, we have two threads simultaneously evicting the same inode, which may trigger the BUG(inode->i_state & I_CLEAR) statement both within clear_inode() and iput(). To fix the bug, recheck the inode->i_count after holding i_lock. Because in the most scenarios, the first check is valid, and the overhead of spin_lock() can be reduced. If there is any misunderstanding, please let me know, thanks. [1]: https://lore.kernel.org/linux-btrfs/000000000000eabe1d0619c48986@google.com/ [2]: The reason might be 1. SB_ACTIVE was removed or 2. mapping_shrinkable() return false when I reproduced the bug.

In the Linux kernel, the following vulnerability has been resolved: ext4: fix race condition between ext4_write and ext4_convert_inline_data Hulk Robot reported a BUG_ON: ================================================================== EXT4-fs error (device loop3): ext4_mb_generate_buddy:805: group 0, block bitmap and bg descriptor inconsistent: 25 vs 31513 free clusters kernel BUG at fs/ext4/ext4_jbd2.c:53! invalid opcode: 0000 [#1] SMP KASAN PTI CPU: 0 PID: 25371 Comm: syz-executor.3 Not tainted 5.10.0+ #1 RIP: 0010:ext4_put_nojournal fs/ext4/ext4_jbd2.c:53 [inline] RIP: 0010:__ext4_journal_stop+0x10e/0x110 fs/ext4/ext4_jbd2.c:116 [...] Call Trace: ext4_write_inline_data_end+0x59a/0x730 fs/ext4/inline.c:795 generic_perform_write+0x279/0x3c0 mm/filemap.c:3344 ext4_buffered_write_iter+0x2e3/0x3d0 fs/ext4/file.c:270 ext4_file_write_iter+0x30a/0x11c0 fs/ext4/file.c:520 do_iter_readv_writev+0x339/0x3c0 fs/read_write.c:732 do_iter_write+0x107/0x430 fs/read_write.c:861 vfs_writev fs/read_write.c:934 [inline] do_pwritev+0x1e5/0x380 fs/read_write.c:1031 [...] ================================================================== Above issue may happen as follows: cpu1 cpu2 __________________________|__________________________ do_pwritev vfs_writev do_iter_write ext4_file_write_iter ext4_buffered_write_iter generic_perform_write ext4_da_write_begin vfs_fallocate ext4_fallocate ext4_convert_inline_data ext4_convert_inline_data_nolock ext4_destroy_inline_data_nolock clear EXT4_STATE_MAY_INLINE_DATA ext4_map_blocks ext4_ext_map_blocks ext4_mb_new_blocks ext4_mb_regular_allocator ext4_mb_good_group_nolock ext4_mb_init_group ext4_mb_init_cache ext4_mb_generate_buddy --> error ext4_test_inode_state(inode, EXT4_STATE_MAY_INLINE_DATA) ext4_restore_inline_data set EXT4_STATE_MAY_INLINE_DATA ext4_block_write_begin ext4_da_write_end ext4_test_inode_state(inode, EXT4_STATE_MAY_INLINE_DATA) ext4_write_inline_data_end handle=NULL ext4_journal_stop(handle) __ext4_journal_stop ext4_put_nojournal(handle) ref_cnt = (unsigned long)handle BUG_ON(ref_cnt == 0) ---> BUG_ON The lock held by ext4_convert_inline_data is xattr_sem, but the lock held by generic_perform_write is i_rwsem. Therefore, the two locks can be concurrent. To solve above issue, we add inode_lock() for ext4_convert_inline_data(). At the same time, move ext4_convert_inline_data() in front of ext4_punch_hole(), remove similar handling from ext4_punch_hole().

In the Linux kernel, the following vulnerability has been resolved: fscache: Fix oops due to race with cookie_lru and use_cookie If a cookie expires from the LRU and the LRU_DISCARD flag is set, but the state machine has not run yet, it's possible another thread can call fscache_use_cookie and begin to use it. When the cookie_worker finally runs, it will see the LRU_DISCARD flag set, transition the cookie->state to LRU_DISCARDING, which will then withdraw the cookie. Once the cookie is withdrawn the object is removed the below oops will occur because the object associated with the cookie is now NULL. Fix the oops by clearing the LRU_DISCARD bit if another thread uses the cookie before the cookie_worker runs. BUG: kernel NULL pointer dereference, address: 0000000000000008 ... CPU: 31 PID: 44773 Comm: kworker/u130:1 Tainted: G E 6.0.0-5.dneg.x86_64 #1 Hardware name: Google Compute Engine/Google Compute Engine, BIOS Google 08/26/2022 Workqueue: events_unbound netfs_rreq_write_to_cache_work [netfs] RIP: 0010:cachefiles_prepare_write+0x28/0x90 [cachefiles] ... Call Trace: netfs_rreq_write_to_cache_work+0x11c/0x320 [netfs] process_one_work+0x217/0x3e0 worker_thread+0x4a/0x3b0 kthread+0xd6/0x100

In the Linux kernel, the following vulnerability has been resolved: ice: Fix race condition during interface enslave Commit 5dbbbd01cbba83 ("ice: Avoid RTNL lock when re-creating auxiliary device") changes a process of re-creation of aux device so ice_plug_aux_dev() is called from ice_service_task() context. This unfortunately opens a race window that can result in dead-lock when interface has left LAG and immediately enters LAG again. Reproducer: ``` #!/bin/sh ip link add lag0 type bond mode 1 miimon 100 ip link set lag0 for n in {1..10}; do echo Cycle: $n ip link set ens7f0 master lag0 sleep 1 ip link set ens7f0 nomaster done ``` This results in: [20976.208697] Workqueue: ice ice_service_task [ice] [20976.213422] Call Trace: [20976.215871] __schedule+0x2d1/0x830 [20976.219364] schedule+0x35/0xa0 [20976.222510] schedule_preempt_disabled+0xa/0x10 [20976.227043] __mutex_lock.isra.7+0x310/0x420 [20976.235071] enum_all_gids_of_dev_cb+0x1c/0x100 [ib_core] [20976.251215] ib_enum_roce_netdev+0xa4/0xe0 [ib_core] [20976.256192] ib_cache_setup_one+0x33/0xa0 [ib_core] [20976.261079] ib_register_device+0x40d/0x580 [ib_core] [20976.266139] irdma_ib_register_device+0x129/0x250 [irdma] [20976.281409] irdma_probe+0x2c1/0x360 [irdma] [20976.285691] auxiliary_bus_probe+0x45/0x70 [20976.289790] really_probe+0x1f2/0x480 [20976.298509] driver_probe_device+0x49/0xc0 [20976.302609] bus_for_each_drv+0x79/0xc0 [20976.306448] __device_attach+0xdc/0x160 [20976.310286] bus_probe_device+0x9d/0xb0 [20976.314128] device_add+0x43c/0x890 [20976.321287] __auxiliary_device_add+0x43/0x60 [20976.325644] ice_plug_aux_dev+0xb2/0x100 [ice] [20976.330109] ice_service_task+0xd0c/0xed0 [ice] [20976.342591] process_one_work+0x1a7/0x360 [20976.350536] worker_thread+0x30/0x390 [20976.358128] kthread+0x10a/0x120 [20976.365547] ret_from_fork+0x1f/0x40 ... [20976.438030] task:ip state:D stack: 0 pid:213658 ppid:213627 flags:0x00004084 [20976.446469] Call Trace: [20976.448921] __schedule+0x2d1/0x830 [20976.452414] schedule+0x35/0xa0 [20976.455559] schedule_preempt_disabled+0xa/0x10 [20976.460090] __mutex_lock.isra.7+0x310/0x420 [20976.464364] device_del+0x36/0x3c0 [20976.467772] ice_unplug_aux_dev+0x1a/0x40 [ice] [20976.472313] ice_lag_event_handler+0x2a2/0x520 [ice] [20976.477288] notifier_call_chain+0x47/0x70 [20976.481386] __netdev_upper_dev_link+0x18b/0x280 [20976.489845] bond_enslave+0xe05/0x1790 [bonding] [20976.494475] do_setlink+0x336/0xf50 [20976.502517] __rtnl_newlink+0x529/0x8b0 [20976.543441] rtnl_newlink+0x43/0x60 [20976.546934] rtnetlink_rcv_msg+0x2b1/0x360 [20976.559238] netlink_rcv_skb+0x4c/0x120 [20976.563079] netlink_unicast+0x196/0x230 [20976.567005] netlink_sendmsg+0x204/0x3d0 [20976.570930] sock_sendmsg+0x4c/0x50 [20976.574423] ____sys_sendmsg+0x1eb/0x250 [20976.586807] ___sys_sendmsg+0x7c/0xc0 [20976.606353] __sys_sendmsg+0x57/0xa0 [20976.609930] do_syscall_64+0x5b/0x1a0 [20976.613598] entry_SYSCALL_64_after_hwframe+0x65/0xca 1. Command 'ip link ... set nomaster' causes that ice_plug_aux_dev() is called from ice_service_task() context, aux device is created and associated device->lock is taken. 2. Command 'ip link ... set master...' calls ice's notifier under RTNL lock and that notifier calls ice_unplug_aux_dev(). That function tries to take aux device->lock but this is already taken by ice_plug_aux_dev() in step 1 3. Later ice_plug_aux_dev() tries to take RTNL lock but this is already taken in step 2 4. Dead-lock The patch fixes this issue by following changes: - Bit ICE_FLAG_PLUG_AUX_DEV is kept to be set during ice_plug_aux_dev() call in ice_service_task() - The bit is checked in ice_clear_rdma_cap() and only if it is not set then ice_unplug_aux_dev() is called. If it is set (in other words plugging of aux device was requested and ice_plug_aux_dev() is potentially running) then the function only clears the ---truncated---

In the Linux kernel, the following vulnerability has been resolved: xsk: Fix race at socket teardown Fix a race in the xsk socket teardown code that can lead to a NULL pointer dereference splat. The current xsk unbind code in xsk_unbind_dev() starts by setting xs->state to XSK_UNBOUND, sets xs->dev to NULL and then waits for any NAPI processing to terminate using synchronize_net(). After that, the release code starts to tear down the socket state and free allocated memory. BUG: kernel NULL pointer dereference, address: 00000000000000c0 PGD 8000000932469067 P4D 8000000932469067 PUD 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 25 PID: 69132 Comm: grpcpp_sync_ser Tainted: G I 5.16.0+ #2 Hardware name: Dell Inc. PowerEdge R730/0599V5, BIOS 1.2.10 03/09/2015 RIP: 0010:__xsk_sendmsg+0x2c/0x690 [...] RSP: 0018:ffffa2348bd13d50 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000040 RCX: ffff8d5fc632d258 RDX: 0000000000400000 RSI: ffffa2348bd13e10 RDI: ffff8d5fc5489800 RBP: ffffa2348bd13db0 R08: 0000000000000000 R09: 00007ffffffff000 R10: 0000000000000000 R11: 0000000000000000 R12: ffff8d5fc5489800 R13: ffff8d5fcb0f5140 R14: ffff8d5fcb0f5140 R15: 0000000000000000 FS: 00007f991cff9400(0000) GS:ffff8d6f1f700000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000000000c0 CR3: 0000000114888005 CR4: 00000000001706e0 Call Trace: <TASK> ? aa_sk_perm+0x43/0x1b0 xsk_sendmsg+0xf0/0x110 sock_sendmsg+0x65/0x70 __sys_sendto+0x113/0x190 ? debug_smp_processor_id+0x17/0x20 ? fpregs_assert_state_consistent+0x23/0x50 ? exit_to_user_mode_prepare+0xa5/0x1d0 __x64_sys_sendto+0x29/0x30 do_syscall_64+0x3b/0xc0 entry_SYSCALL_64_after_hwframe+0x44/0xae There are two problems with the current code. First, setting xs->dev to NULL before waiting for all users to stop using the socket is not correct. The entry to the data plane functions xsk_poll(), xsk_sendmsg(), and xsk_recvmsg() are all guarded by a test that xs->state is in the state XSK_BOUND and if not, it returns right away. But one process might have passed this test but still have not gotten to the point in which it uses xs->dev in the code. In this interim, a second process executing xsk_unbind_dev() might have set xs->dev to NULL which will lead to a crash for the first process. The solution here is just to get rid of this NULL assignment since it is not used anymore. Before commit 42fddcc7c64b ("xsk: use state member for socket synchronization"), xs->dev was the gatekeeper to admit processes into the data plane functions, but it was replaced with the state variable xs->state in the aforementioned commit. The second problem is that synchronize_net() does not wait for any process in xsk_poll(), xsk_sendmsg(), or xsk_recvmsg() to complete, which means that the state they rely on might be cleaned up prematurely. This can happen when the notifier gets called (at driver unload for example) as it uses xsk_unbind_dev(). Solve this by extending the RCU critical region from just the ndo_xsk_wakeup to the whole functions mentioned above, so that both the test of xs->state == XSK_BOUND and the last use of any member of xs is covered by the RCU critical section. This will guarantee that when synchronize_net() completes, there will be no processes left executing xsk_poll(), xsk_sendmsg(), or xsk_recvmsg() and state can be cleaned up safely. Note that we need to drop the RCU lock for the skb xmit path as it uses functions that might sleep. Due to this, we have to retest the xs->state after we grab the mutex that protects the skb xmit code from, among a number of things, an xsk_unbind_dev() being executed from the notifier at the same time.

In the Linux kernel, the following vulnerability has been resolved: ibmvnic: fix race between xmit and reset There is a race between reset and the transmit paths that can lead to ibmvnic_xmit() accessing an scrq after it has been freed in the reset path. It can result in a crash like: Kernel attempted to read user page (0) - exploit attempt? (uid: 0) BUG: Kernel NULL pointer dereference on read at 0x00000000 Faulting instruction address: 0xc0080000016189f8 Oops: Kernel access of bad area, sig: 11 [#1] ... NIP [c0080000016189f8] ibmvnic_xmit+0x60/0xb60 [ibmvnic] LR [c000000000c0046c] dev_hard_start_xmit+0x11c/0x280 Call Trace: [c008000001618f08] ibmvnic_xmit+0x570/0xb60 [ibmvnic] (unreliable) [c000000000c0046c] dev_hard_start_xmit+0x11c/0x280 [c000000000c9cfcc] sch_direct_xmit+0xec/0x330 [c000000000bfe640] __dev_xmit_skb+0x3a0/0x9d0 [c000000000c00ad4] __dev_queue_xmit+0x394/0x730 [c008000002db813c] __bond_start_xmit+0x254/0x450 [bonding] [c008000002db8378] bond_start_xmit+0x40/0xc0 [bonding] [c000000000c0046c] dev_hard_start_xmit+0x11c/0x280 [c000000000c00ca4] __dev_queue_xmit+0x564/0x730 [c000000000cf97e0] neigh_hh_output+0xd0/0x180 [c000000000cfa69c] ip_finish_output2+0x31c/0x5c0 [c000000000cfd244] __ip_queue_xmit+0x194/0x4f0 [c000000000d2a3c4] __tcp_transmit_skb+0x434/0x9b0 [c000000000d2d1e0] __tcp_retransmit_skb+0x1d0/0x6a0 [c000000000d2d984] tcp_retransmit_skb+0x34/0x130 [c000000000d310e8] tcp_retransmit_timer+0x388/0x6d0 [c000000000d315ec] tcp_write_timer_handler+0x1bc/0x330 [c000000000d317bc] tcp_write_timer+0x5c/0x200 [c000000000243270] call_timer_fn+0x50/0x1c0 [c000000000243704] __run_timers.part.0+0x324/0x460 [c000000000243894] run_timer_softirq+0x54/0xa0 [c000000000ea713c] __do_softirq+0x15c/0x3e0 [c000000000166258] __irq_exit_rcu+0x158/0x190 [c000000000166420] irq_exit+0x20/0x40 [c00000000002853c] timer_interrupt+0x14c/0x2b0 [c000000000009a00] decrementer_common_virt+0x210/0x220 --- interrupt: 900 at plpar_hcall_norets_notrace+0x18/0x2c The immediate cause of the crash is the access of tx_scrq in the following snippet during a reset, where the tx_scrq can be either NULL or an address that will soon be invalid: ibmvnic_xmit() { ... tx_scrq = adapter->tx_scrq[queue_num]; txq = netdev_get_tx_queue(netdev, queue_num); ind_bufp = &tx_scrq->ind_buf; if (test_bit(0, &adapter->resetting)) { ... } But beyond that, the call to ibmvnic_xmit() itself is not safe during a reset and the reset path attempts to avoid this by stopping the queue in ibmvnic_cleanup(). However just after the queue was stopped, an in-flight ibmvnic_complete_tx() could have restarted the queue even as the reset is progressing. Since the queue was restarted we could get a call to ibmvnic_xmit() which can then access the bad tx_scrq (or other fields). We cannot however simply have ibmvnic_complete_tx() check the ->resetting bit and skip starting the queue. This can race at the "back-end" of a good reset which just restarted the queue but has not cleared the ->resetting bit yet. If we skip restarting the queue due to ->resetting being true, the queue would remain stopped indefinitely potentially leading to transmit timeouts. IOW ->resetting is too broad for this purpose. Instead use a new flag that indicates whether or not the queues are active. Only the open/ reset paths control when the queues are active. ibmvnic_complete_tx() and others wake up the queue only if the queue is marked active. So we will have: A. reset/open thread in ibmvnic_cleanup() and __ibmvnic_open() ->resetting = true ->tx_queues_active = false disable tx queues ... ->tx_queues_active = true start tx queues B. Tx interrupt in ibmvnic_complete_tx(): if (->tx_queues_active) netif_wake_subqueue(); To ensure that ->tx_queues_active and state of the queues are consistent, we need a lock which: - must also be taken in the interrupt path (ibmvnic_complete_tx()) - shared across the multiple ---truncated---

In the Linux kernel, the following vulnerability has been resolved: list: fix a data-race around ep->rdllist ep_poll() first calls ep_events_available() with no lock held and checks if ep->rdllist is empty by list_empty_careful(), which reads rdllist->prev. Thus all accesses to it need some protection to avoid store/load-tearing. Note INIT_LIST_HEAD_RCU() already has the annotation for both prev and next. Commit bf3b9f6372c4 ("epoll: Add busy poll support to epoll with socket fds.") added the first lockless ep_events_available(), and commit c5a282e9635e ("fs/epoll: reduce the scope of wq lock in epoll_wait()") made some ep_events_available() calls lockless and added single call under a lock, finally commit e59d3c64cba6 ("epoll: eliminate unnecessary lock for zero timeout") made the last ep_events_available() lockless. BUG: KCSAN: data-race in do_epoll_wait / do_epoll_wait write to 0xffff88810480c7d8 of 8 bytes by task 1802 on cpu 0: INIT_LIST_HEAD include/linux/list.h:38 [inline] list_splice_init include/linux/list.h:492 [inline] ep_start_scan fs/eventpoll.c:622 [inline] ep_send_events fs/eventpoll.c:1656 [inline] ep_poll fs/eventpoll.c:1806 [inline] do_epoll_wait+0x4eb/0xf40 fs/eventpoll.c:2234 do_epoll_pwait fs/eventpoll.c:2268 [inline] __do_sys_epoll_pwait fs/eventpoll.c:2281 [inline] __se_sys_epoll_pwait+0x12b/0x240 fs/eventpoll.c:2275 __x64_sys_epoll_pwait+0x74/0x80 fs/eventpoll.c:2275 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x44/0xae read to 0xffff88810480c7d8 of 8 bytes by task 1799 on cpu 1: list_empty_careful include/linux/list.h:329 [inline] ep_events_available fs/eventpoll.c:381 [inline] ep_poll fs/eventpoll.c:1797 [inline] do_epoll_wait+0x279/0xf40 fs/eventpoll.c:2234 do_epoll_pwait fs/eventpoll.c:2268 [inline] __do_sys_epoll_pwait fs/eventpoll.c:2281 [inline] __se_sys_epoll_pwait+0x12b/0x240 fs/eventpoll.c:2275 __x64_sys_epoll_pwait+0x74/0x80 fs/eventpoll.c:2275 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x44/0xae value changed: 0xffff88810480c7d0 -> 0xffff888103c15098 Reported by Kernel Concurrency Sanitizer on: CPU: 1 PID: 1799 Comm: syz-fuzzer Tainted: G W 5.17.0-rc7-syzkaller-dirty #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

In the Linux kernel, the following vulnerability has been resolved: nbd: fix race between nbd_alloc_config() and module removal When nbd module is being removing, nbd_alloc_config() may be called concurrently by nbd_genl_connect(), although try_module_get() will return false, but nbd_alloc_config() doesn't handle it. The race may lead to the leak of nbd_config and its related resources (e.g, recv_workq) and oops in nbd_read_stat() due to the unload of nbd module as shown below: BUG: kernel NULL pointer dereference, address: 0000000000000040 Oops: 0000 [#1] SMP PTI CPU: 5 PID: 13840 Comm: kworker/u17:33 Not tainted 5.14.0+ #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996) Workqueue: knbd16-recv recv_work [nbd] RIP: 0010:nbd_read_stat.cold+0x130/0x1a4 [nbd] Call Trace: recv_work+0x3b/0xb0 [nbd] process_one_work+0x1ed/0x390 worker_thread+0x4a/0x3d0 kthread+0x12a/0x150 ret_from_fork+0x22/0x30 Fixing it by checking the return value of try_module_get() in nbd_alloc_config(). As nbd_alloc_config() may return ERR_PTR(-ENODEV), assign nbd->config only when nbd_alloc_config() succeeds to ensure the value of nbd->config is binary (valid or NULL). Also adding a debug message to check the reference counter of nbd_config during module removal.

In the Linux kernel, the following vulnerability has been resolved: af_unix: Fix a data-race in unix_dgram_peer_wake_me(). unix_dgram_poll() calls unix_dgram_peer_wake_me() without `other`'s lock held and check if its receive queue is full. Here we need to use unix_recvq_full_lockless() instead of unix_recvq_full(), otherwise KCSAN will report a data-race.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Always drain health in shutdown callback There is no point in recovery during device shutdown. if health work started need to wait for it to avoid races and NULL pointer access. Hence, drain health WQ on shutdown callback.