D-Link DAP-1860 devices before v1.04b03 Beta allow arbitrary remote code execution as root without authentication via shell metacharacters within an HNAP_AUTH HTTP header.

Authentication Bypass vulnerability in D-Link DIR-645 firmware version 1.03 allows remote attackers to gain escalated privileges via function phpcgi_main in cgibin. NOTE: This vulnerability only affects products that are no longer supported by the maintainer.

Authentication Bypass vulnerability in D-Link DIR-895 FW102b07 allows remote attackers to gain escalated privileges via via function phpcgi_main in cgibin. NOTE: This vulnerability only affects products that are no longer supported by the maintainer.

Authentication Bypass vulnerability in D-Link DIR-885L FW102b01 allows remote attackers to gain escalated privileges via phpcgi. NOTE: This vulnerability only affects products that are no longer supported by the maintainer.

An access control issue in the component formDMZ.cgi of D-Link 816A2_FWv1.10CNB05_R1B011D88210 allows unauthenticated attackers to set the DMZ service of the device via a crafted POST request.

An issue was discovered on D-Link DCS-1100 and DCS-1130 devices. The device has a custom telnet daemon as a part of the busybox and retrieves the password from the shadow file using the function getspnam at address 0x00053894. Then performs a crypt operation on the password retrieved from the user at address 0x000538E0 and performs a strcmp at address 0x00053908 to check if the password is correct or incorrect. However, the /etc/shadow file is a part of CRAM-FS filesystem which means that the user cannot change the password and hence a hardcoded hash in /etc/shadow is used to match the credentials provided by the user. This is a salted hash of the string "admin" and hence it acts as a password to the device which cannot be changed as the whole filesystem is read only.

An issue was discovered on D-Link DCS-1100 and DCS-1130 devices. The device requires that a user logging into the device provide a username and password. However, the device allows D-Link apps on the mobile devices and desktop to communicate with the device without any authentication. As a part of that communication, the device uses custom version of base64 encoding to pass data back and forth between the apps and the device. However, the same form of communication can be initiated by any process including an attacker process on the mobile phone or the desktop and this allows a third party to retrieve the device's password without any authentication by sending just 1 UDP packet with custom base64 encoding. The severity of this attack is enlarged by the fact that there more than 100,000 D-Link devices out there.

Multiple SQL injection vulnerabilities in D-Link DSR-150 with firmware before 1.08B44; DSR-150N with firmware before 1.05B64; DSR-250 and DSR-250N with firmware before 1.08B44; and DSR-500, DSR-500N, DSR-1000, and DSR-1000N with firmware before 1.08B77 allow remote attackers to execute arbitrary SQL commands via the password to (1) the login.authenticate function in share/lua/5.1/teamf1lualib/login.lua or (2) captivePortal.lua.

Buffer Overflow vulnerability in D-Link DSR-150, DSR-150N, DSR-250, DSR-250N, DSR-500N, DSR-1000N from 3.13 to 3.17B901C allows unauthenticated users to execute remote code execution.

An issue was discovered on D-Link DCS-1100 and DCS-1130 devices. The device runs a custom daemon on UDP port 5978 which is called "dldps2121" and listens for broadcast packets sent on 255.255.255.255. This daemon handles custom D-Link UDP based protocol that allows D-Link mobile applications and desktop applications to discover D-Link devices on the local network. The binary processes the received UDP packets sent from any device in "main" function. One path in the function traverses towards a block of code that handles commands to be executed on the device. The custom protocol created by D-Link follows the following pattern: Packetlen, Type of packet; M=MAC address of device or broadcast; D=Device Type;C=base64 encoded command string;test=1111. If a packet is received with the packet type being "S" or 0x53 then the string passed in the "C" parameter is base64 decoded and then executed by passing into a System API. We can see at address 0x00009B44 that the string received in packet type subtracts 0x31 or "1" from the packet type and is compared against 0x22 or "double quotes". If that is the case, then the packet is sent towards the block of code that executes a command. Then the value stored in "C" parameter is extracted at address 0x0000A1B0. Finally, the string received is base 64 decoded and passed on to the system API at address 0x0000A2A8 as shown below. The same form of communication can be initiated by any process including an attacker process on the mobile phone or the desktop and this allows a third-party application on the device to execute commands on the device without any authentication by sending just 1 UDP packet with custom base64 encoding.

D-Link device DI-7200GV2.E1 v21.04.09E1 was discovered to contain a command injection vulnerability in the function upgrade_filter. This vulnerability allows attackers to execute arbitrary commands via the path and time parameters.

An issue was discovered on D-Link DCS-1100 and DCS-1130 devices. The binary rtspd in /sbin folder of the device handles all the rtsp connections received by the device. It seems that the binary performs a memcpy operation at address 0x00011E34 with the value sent in the "Authorization: Basic" RTSP header and stores it on the stack. The number of bytes to be copied are calculated based on the length of the string sent in the RTSP header by the client. As a result, memcpy copies more data then it can hold on stack and this results in corrupting the registers for the caller function sub_F6CC which results in memory corruption. The severity of this attack is enlarged by the fact that the same value is then copied on the stack in the function 0x00011378 and this allows to overflow the buffer allocated and thus control the PC register which will result in arbitrary code execution on the device.

D-Link device DIR_878_FW1.30B08_Hotfix_02 was discovered to contain a command injection vulnerability in the twsystem function. This vulnerability allows attackers to execute arbitrary commands via a crafted HNAP1 POST request.

D-Link device D-Link DIR-823-Pro v1.0.2 was discovered to contain a command injection vulnerability in the function SetNetworkTomographySettings. This vulnerability allows attackers to execute arbitrary commands via the tomography_ping_address, tomography_ping_number, tomography_ping_size, tomography_ping_timeout, and tomography_ping_ttl parameters.

D-Link device DIR_882 DIR_882_FW1.30B06_Hotfix_02 was discovered to contain a command injection vulnerability in the LocalIPAddress parameter. This vulnerability allows attackers to execute arbitrary commands via a crafted HNAP1 POST request.

D-Link device DIR_882 DIR_882_FW1.30B06_Hotfix_02 was discovered to contain a command injection vulnerability in the twsystem function. This vulnerability allows attackers to execute arbitrary commands via a crafted HNAP1 POST request.

D-Link device DI-7200GV2.E1 v21.04.09E1 was discovered to contain a command injection vulnerability in the function msp_info.htm. This vulnerability allows attackers to execute arbitrary commands via the cmd parameter.

A Remote Command Execution (RCE) vulnerability exists in HNAP1/control/SetNetworkTomographySettings.php of D-Link Router DIR-846 DIR846A1_FW100A43.bin and DIR846enFW100A53DLA-Retail.bin because backticks can be used for command injection when judging whether it is a reasonable domain name.

D-Link DIR-822 Rev.Bx devices with firmware v.202KRb06 and older allow a buffer overflow via long MacAddress data in a /HNAP1/SetClientInfo HNAP protocol message, which is mishandled in /usr/sbin/udhcpd during reading of the /var/servd/LAN-1-udhcpd.conf file.

D-Link DIR-865L has PHP File Inclusion in the router xml file.

The D-Link DIR-615 device before v20.12PTb04 doesn't use SSL for any of the authenticated pages. Also, it doesn't allow the user to generate his own SSL Certificate. An attacker can simply monitor network traffic to steal a user's credentials and/or credentials of users being added while sniffing the traffic.

D-Link device D-Link DIR-823-Pro v1.0.2 was discovered to contain a command injection vulnerability in the function SetStaticRouteSettings. This vulnerability allows attackers to execute arbitrary commands via the staticroute_list parameter.

D-Link G416 flupl self Command Injection Remote Code Execution Vulnerability. This vulnerability allows network-adjacent attackers to execute arbitrary code on affected installations of D-Link G416 wireless routers. Authentication is not required to exploit this vulnerability. The specific flaw exists within the HTTP service listening on TCP port 80. The issue results from the lack of proper validation of a user-supplied string before using it to execute a system call. An attacker can leverage this vulnerability to execute code in the context of root. Was ZDI-CAN-21294.

D-LINK DI-8003 v16.07.26A1 was discovered to contain a buffer overflow via the ip parameter in the ip_position_asp function.

D-Link device DI-7200GV2.E1 v21.04.09E1 was discovered to contain a command injection vulnerability in the function proxy_client.asp. This vulnerability allows attackers to execute arbitrary commands via the proxy_srv, proxy_srvport, proxy_lanip, proxy_lanport parameters.

D-Link device DI-7200GV2.E1 v21.04.09E1 was discovered to contain a command injection vulnerability in the function urlrd_opt.asp. This vulnerability allows attackers to execute arbitrary commands via the url_en parameter.

** UNSUPPORTED WHEN ASSIGNED ** A vulnerability, which was classified as critical, has been found in D-Link DAR-7000-40 V31R02B1413C. Affected by this issue is some unknown functionality of the file /useratte/resmanage.php. The manipulation of the argument file leads to unrestricted upload. The attack may be launched remotely. The exploit has been disclosed to the public and may be used. VDB-264530 is the identifier assigned to this vulnerability. NOTE: This vulnerability only affects products that are no longer supported by the maintainer. NOTE: Vendor was contacted early and confirmed immediately that the product is end-of-life. It should be retired and replaced.

** UNSUPPORTED WHEN ASSIGNED ** A vulnerability has been found in D-Link DAR-7000-40 V31R02B1413C and classified as critical. This vulnerability affects unknown code of the file /firewall/urlblist.php. The manipulation of the argument file leads to unrestricted upload. The attack can be initiated remotely. The exploit has been disclosed to the public and may be used. The identifier of this vulnerability is VDB-264532. NOTE: This vulnerability only affects products that are no longer supported by the maintainer. NOTE: Vendor was contacted early and confirmed immediately that the product is end-of-life. It should be retired and replaced.

An Access Control vulnerability exists in D-Link DIR-823G REVA1 1.02B05 (Lastest) via any parameter in the HNAP1 function

D-Link DIR-865L has SMB Symlink Traversal due to misconfiguration in the SMB service allowing symbolic links to be created to locations outside of the Samba share.

D-Link DIR-645 1.03 A1 is vulnerable to Buffer Overflow. The hnap_main function in the cgibin handler uses sprintf to format the soapaction header onto the stack and has no limit on the size.

In DLink DAP-1360 F1 firmware version <=v6.10 in the "webupg" binary, an attacker can use the "file" parameter to execute arbitrary system commands when the parameter is "name=deleteFile" after being authorized.

Certain models of D-Link wireless routers contain hidden functionality. By sending specific packets to the web service, the attacker can forcibly enable the telnet service and log in using hard-coded credentials. The telnet service enabled through this method can only be accessed from within the same local network as the device.

Missing Authentication for Critical Function vulnerability in debug_post_set.cgi of D-Link DWR-932C E1 firmware allows an unauthenticated attacker to execute administrative actions.

OS Command Injection vulnerability in debug_fcgi of D-Link DWR-932C E1 firmware allows a remote attacker to perform command injection via a crafted HTTP request.

D-Link DI-7003GV2 v24.04.18D1, DI-7100G+V2 v24.04.18D1, DI-7100GV2 v24.04.18D1, DI-7200GV2 v24.04.18E1, DI-7300G+V2 v24.04.18D1, and DI-7400G+V2 v24.04.18D1 are vulnerable to Remote Command Execution. An attacker can achieve arbitrary command execution by sending a carefully crafted malicious string to the CGI function responsible for handling usb_paswd.asp.

Remote Command Execution (RCE) vulnerability exists in HNAP1/control/SetWizardConfig.php in D-Link Router DIR-846 DIR846A1_FW100A43.bin and DIR846enFW100A53DLA-Retail.bin. Malicoius users can use this vulnerability to use "\ " or backticks in the shell metacharacters in the ssid0 or ssid1 parameters to cause arbitrary command execution. Since CVE-2019-17510 vulnerability has not been patched and improved www/hnap1/control/setwizardconfig.php, can also use line breaks and backquotes to bypass.

D-Link DI-8100G 17.12.20A1 is vulnerable to Command Injection via msp_info.htm.

D-Link DI-8100G 17.12.20A1 is vulnerable to Command Injection via sub47A60C function in the upgrade_filter.asp file

D-Link DI_8004W 16.07.26A1 contains a command execution vulnerability in the jhttpd upgrade_filter_asp function.

Stack overflow vulnerability in the Login function in the HNAP service in D-Link DCS-960L with firmware 1.09 allows attackers to execute of arbitrary code.

D-Link device D-Link DIR-823-Pro v1.0.2 was discovered to contain a command injection vulnerability in the function SetWLanApcliSettings. This vulnerability allows attackers to execute arbitrary commands via the ApCliKeyStr parameter.

DBA-1510P firmware 1.70b009 and earlier allows an attacker to execute arbitrary OS commands via Web User Interface.

D-Link DI-8300 v16.07.26A1 is vulnerable to command injection via the upgrade_filter_asp function.

D-Link DIR-846W A1 FW100A43 was discovered to contain a remote command execution (RCE) vulnerability via the wl(0).(0)_ssid parameter. This vulnerability is exploited via a crafted POST request.

D-Link DI-7003G v19.12.24A1, DI-7003GV2 v24.04.18D1, DI-7100G+V2 v24.04.18D1, DI-7100GV2 v24.04.18D1, DI-7200GV2 v24.04.18E1, DI-7300G+V2 v24.04.18D1, and DI-7400G+V2 v24.04.18D1 are vulnerable to Remote Command Execution (RCE) via version_upgrade.asp.

D-Link DIR-846W A1 FW100A43 was discovered to contain a remote command execution (RCE) vulnerability via the lan(0)_dhcps_staticlist parameter. This vulnerability is exploited via a crafted POST request.

D-Link DI-7003GV2 v24.04.18D1, DI-7100G+V2 v24.04.18D1, DI-7100GV2 v24.04.18D1, DI-7200GV2 v24.04.18E1, DI-7300G+V2 v24.04.18D1, and DI-7400G+V2 v24.04.18D1 are vulnerable to Remote Command Execution due to insufficient parameter filtering in the CGI handling function of upgrade_filter.asp.

A vulnerability was discovered in DI_8400-16.07.26A1, which has been classified as critical. This issue affects the upgrade_filter_asp function in the upgrade_filter.asp file. Manipulation of the path parameter can lead to command injection.