An Improper Input Validation vulnerability in Juniper Tunnel Driver (jtd) and ICMP module of Juniper Networks Junos OS Evolved allows an unauthenticated attacker within the MPLS administrative domain to send specifically crafted packets to the Routing Engine (RE) to cause a Denial of Service (DoS). When specifically crafted transit MPLS IPv4 packets are received by the Packet Forwarding Engine (PFE), these packets are internally forwarded to the RE. Continued receipt of these packets may create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS: * All versions before 21.2R3-S8-EVO; * from 21.4-EVO before 21.4R3-S6-EVO; * from 22.2-EVO before 22.2R3-S4-EVO; * from 22.3-EVO before 22.3R3-S3-EVO; * from 22.4-EVO before 22.4R3-EVO; * from 23.2-EVO before 23.2R2-EVO. * from 23.4-EVO before 23.4R1-S1-EVO.
A Missing Release of Memory after Effective Lifetime vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on MX Series allows an adjacent, unauthenticated attacker to cause a Denial of Service (DoS). If an MX Series device receives PTP packets on an MPC3E that doesn't support PTP this causes a memory leak which will result in unpredictable behavior and ultimately in an MPC crash and restart. To monitor for this issue, please use the following FPC vty level commands: show heap shows an increase in "LAN buffer" utilization and show clksync ptp nbr-upd-info shows non-zero "Pending PFEs" counter. This issue affects Juniper Networks Junos OS on MX Series with MPC3E: * All versions earlier than 20.4R3-S3; * 21.1 versions earlier than 21.1R3-S4; * 21.2 versions earlier than 21.2R3; * 21.3 versions earlier than 21.3R2-S1, 21.3R3; * 21.4 versions earlier than 21.4R2; * 22.1 versions earlier than 22.1R2.
A Missing Release of Memory after Effective Lifetime vulnerability in the IKE daemon (iked) of Juniper Networks Junos OS on MX Series with SPC3, and SRX Series allows an administratively adjacent attacker which is able to successfully establish IPsec tunnels to cause a Denial of Service (DoS). If specific values for the IPsec parameters local-ip, remote-ip, remote ike-id, and traffic selectors are sent from the peer, a memory leak occurs during every IPsec SA rekey which is carried out with a specific message sequence. This will eventually result in an iked process crash and restart. The iked process memory consumption can be checked using the below command: user@host> show system processes extensive | grep iked PID USERNAME PRI NICE SIZE RES STATE C TIME WCPU COMMAND 56903 root 31 0 4016M 2543M CPU0 0 2:10 10.50% iked This issue affects Juniper Networks Junos OS: * All versions earlier than 20.4R3-S9; * 21.2 versions earlier than 21.2R3-S7; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S4; * 22.1 versions earlier than 22.1R3-S3; * 22.2 versions earlier than 22.2R3-S2; * 22.3 versions earlier than 22.3R3; * 22.4 versions earlier than 22.4R3; * 23.2 versions earlier than 23.2R1-S2, 23.2R2.
A Missing Release of Memory after Effective Lifetime vulnerability in Routing Protocol Daemon (RPD) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, adjacent attacker to cause an rpd crash, leading to Denial of Service (DoS). On all Junos OS and Junos OS Evolved platforms, when traffic engineering is enabled for OSPF or ISIS, and a link flaps, a patroot memory leak is observed. This memory leak, over time, will lead to an rpd crash and restart. The memory usage can be monitored using the below command. user@host> show task memory detail | match patroot This issue affects: Juniper Networks Junos OS * All versions earlier than 21.2R3-S3; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S3; * 22.1 versions earlier than 22.1R3; * 22.2 versions earlier than 22.2R3. Juniper Networks Junos OS Evolved * All versions earlier than 21.3R3-S5-EVO; * 21.4 versions earlier than 21.4R3-EVO; * 22.1 versions earlier than 22.1R3-EVO; * 22.2 versions earlier than 22.2R3-EVO.
A Missing Release of Memory after Effective Lifetime vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on PTX Series allows an adjacent attacker to cause a Denial of Service (DoS) by sending genuine BGP flowspec packets which cause an FPC heap memory leak. Once having run out of memory the FPC will crash and restart along with a core dump. Continued receipted of these packets will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS All versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S7; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R3-S6; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3-S1; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2. Juniper Networks Junos Evolved is not affected.
An Improper Validation of Syntactic Correctness of Input vulnerability in Routing Protocol Daemon (rpd) Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network based attacker to cause a Denial of Service (DoS). When a malformed BGP UPDATE packet is received over an established BGP session, the rpd crashes and restarts. This issue affects both eBGP and iBGP implementations. This issue affects: Juniper Networks Junos OS * 21.4 versions prior to 21.4R3-S4; * 22.1 versions prior to 22.1R3-S3; * 22.2 versions prior to 22.2R3-S2; * 22.3 versions prior to 22.3R2-S2, 22.3R3; * 22.4 versions prior to 22.4R2-S1, 22.4R3; * 23.2 versions prior to 23.2R1, 23.2R2; Juniper Networks Junos OS Evolved * 21.4 versions prior to 21.4R3-S5-EVO; * 22.1 versions prior to 22.1R3-S3-EVO; * 22.2 versions prior to 22.2R3-S3-EVO; * 22.3 versions prior to 22.3R2-S2-EVO; * 22.4 versions prior to 22.4R3-EVO; * 23.2 versions prior to 23.2R2-EVO;
A Missing Release of Memory after Effective Lifetime vulnerability in the packet forwarding engine (PFE) of Juniper Networks Junos OS on MX Series allows an unauthenticated adjacent attacker to cause a Denial-of-Service (DoS). In a subscriber management scenario, login/logout activity triggers a memory leak, and the leaked memory gradually increments and eventually results in a crash. user@host> show chassis fpc Temp CPU Utilization (%) CPU Utilization (%) Memory Utilization (%) Slot State (C) Total Interrupt 1min 5min 15min DRAM (MB) Heap Buffer 2 Online 36 10 0 9 8 9 32768 26 0 This issue affects Junos OS on MX Series: * All versions before 21.2R3-S9 * from 21.4 before 21.4R3-S10 * from 22.2 before 22.2R3-S6 * from 22.4 before 22.4R3-S5 * from 23.2 before 23.2R2-S3 * from 23.4 before 23.4R2-S3 * from 24.2 before 24.2R2.
A Missing Release of Memory after Effective Lifetime vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS and Junos OS Evolved allows an adjacent, unauthenticated attacker to cause an FPC to crash, leading to Denial of Service (DoS). On all Junos OS and Junos OS Evolved platforms, in an EVPN-VXLAN scenario, when specific ARP packets are received on an IPv4 network, or specific NDP packets are received on an IPv6 network, kernel heap memory leaks, which eventually leads to an FPC crash and restart. This issue does not affect MX Series platforms. Heap size growth on FPC can be seen using below command. user@host> show chassis fpc Temp CPU Utilization (%) CPU Utilization (%) Memory Utilization (%) Slot State (C) Total Interrupt 1min 5min 15min DRAM (MB) Heap Buffer 0 Online 45 3 0 2 2 2 32768 19 0 <<<<<<< Heap increase in all fPCs This issue affects Junos OS: * All versions before 21.2R3-S7, * 21.4 versions before 21.4R3-S4, * 22.2 versions before 22.2R3-S1, * 22.3 versions before 22.3R3-S1, * 22.4 versions before 22.4R2-S2, 22.4R3. and Junos OS Evolved: * All versions before 21.2R3-S7-EVO, * 21.4-EVO versions before 21.4R3-S4-EVO, * 22.2-EVO versions before 22.2R3-S1-EVO, * 22.3-EVO versions before 22.3R3-S1-EVO, * 22.4-EVO versions before 22.4R3-EVO.
A vulnerability in the distributed or centralized periodic packet management daemon (PPMD) of Juniper Networks Junos OS may cause receipt of a malformed packet to crash and restart the PPMD process, leading to network destabilization, service interruption, and a Denial of Service (DoS) condition. Continued receipt and processing of these malformed packets will repeatedly crash the PPMD process and sustain the Denial of Service (DoS) condition. Due to the nature of the specifically crafted packet, exploitation of this issue requires direct, adjacent connectivity to the vulnerable component. This issue affects Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S12, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S6; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S4; 19.2 versions prior to 19.2R1-S5, 19.2R3-S1; 19.3 versions prior to 19.3R2-S5, 19.3R3-S1; 19.4 versions prior to 19.4R2-S2, 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R1-S2, 20.2R2.
On Juniper Networks Junos EX series, QFX Series, MX Series and SRX branch series devices, a memory leak occurs every time the 802.1X authenticator port interface flaps which can lead to other processes, such as the pfex process, responsible for packet forwarding, to crash and restart. An administrator can use the following CLI command to monitor the status of memory consumption: user@device> show task memory detail Please refer to https://kb.juniper.net/KB31522 for details. This issue affects Juniper Networks Junos OS: 14.1X53 versions prior to 14.1X53-D54; 15.1X49 versions prior to 15.1X49-D240 ; 15.1X53 versions prior to 15.1X53-D593; 16.1 versions prior to 16.1R7-S8; 17.2 versions prior to 17.2R3-S4; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S11, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10 ; 18.2 versions prior to 18.2R2-S7, 18.2R3-S3; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3-S2; 19.1 versions prior to 19.1R1-S5, 19.1R2-S2, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2. This issue does not affect Juniper Networks Junos OS 12.3, 15.1.
A kernel memory leak in QFX10002-32Q, QFX10002-60C, QFX10002-72Q, QFX10008, QFX10016 devices Flexible PIC Concentrators (FPCs) on Juniper Networks Junos OS allows an attacker to send genuine packets destined to the device to cause a Denial of Service (DoS) to the device. On QFX10002-32Q, QFX10002-60C, QFX10002-72Q devices the device will crash and restart. On QFX10008, QFX10016 devices, depending on the number of FPCs involved in an attack, one more more FPCs may crash and traffic through the device may be degraded in other ways, until the attack traffic stops. A reboot is required to restore service and clear the kernel memory. Continued receipt and processing of these genuine packets will create a sustained Denial of Service (DoS) condition. On QFX10008, QFX10016 devices, an indicator of compromise may be the existence of DCPFE core files. You can also monitor PFE memory utilization for incremental growth: user@qfx-RE:0% cprod -A fpc0 -c "show heap 0" | grep -i ke 0 3788a1b0 3221225048 2417120656 804104392 24 Kernel user@qfx-RE:0% cprod -A fpc0 -c "show heap 0" | grep -i ke 0 3788a1b0 3221225048 2332332200 888892848 27 Kernel This issue affects: Juniper Networks Junos OS on QFX10002-32Q, QFX10002-60C, QFX10002-72Q, QFX10008, QFX10016: 16.1 versions 16.1R1 and above prior to 17.3 versions prior to 17.3R3-S9; 17.4 versions prior to 17.4R3-S2; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S5; 18.3 versions prior to 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R3-S2; 19.2 versions prior to 19.2R3; 19.3 versions prior to 19.3R3; 19.4 versions prior to 19.4R3; 20.1 versions prior to 20.1R2. This issue does not affect releases prior to Junos OS 16.1R1. This issue does not affect EX Series devices. This issue does not affect Junos OS Evolved.
On Juniper Networks MX Series and EX9200 Series platforms with Trio-based MPCs (Modular Port Concentrators) where Integrated Routing and Bridging (IRB) interfaces are configured and mapped to a VPLS instance or a Bridge-Domain, certain Layer 2 network events at Customer Edge (CE) devices may cause memory leaks in the MPC of Provider Edge (PE) devices which can cause an out of memory condition and MPC restart. When this issue occurs, there will be temporary traffic interruption until the MPC is restored. An administrator can use the following CLI command to monitor the status of memory usage level of the MPC: user@device> show system resource-monitor fpc FPC Resource Usage Summary Free Heap Mem Watermark : 20 % Free NH Mem Watermark : 20 % Free Filter Mem Watermark : 20 % * - Watermark reached Slot # % Heap Free RTT Average RTT 1 87 PFE # % ENCAP mem Free % NH mem Free % FW mem Free 0 NA 88 99 1 NA 89 99 When the issue is occurring, the value of “% NH mem Free” will go down until the MPC restarts. This issue affects MX Series and EX9200 Series with Trio-based PFEs (Packet Forwarding Engines), including MX-MPC1-3D, MX-MPC1E-3D, MX-MPC2-3D, MX-MPC2E-3D, MPC-3D-16XGE, and CHAS-MXxx Series MPCs. No other products or platforms are affected by this issue. This issue affects Juniper Networks Junos OS on MX Series, EX9200 Series: 17.3 versions prior to 17.3R3-S10; 17.4 versions prior to 17.4R3-S3; 18.2 versions prior to 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R3-S6; 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R2-S2, 19.4R3; 20.2 versions prior to 20.2R1-S3, 20.2R2; 20.3 versions prior to 20.3R1-S1,, 20.3R2. This issue does not affect Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R3-S2; 18.1; 18.2 versions prior to 18.2R3-S4; 18.3 versions prior to 18.3R3-S2; 18.4 versions prior to 18.4R3-S1; 19.1; 19.2 versions prior to 19.2R2; 19.3 versions prior to 19.3R3; 19.4 versions prior to 19.4R2.
An Improper Input Validation vulnerability in the active-lease query portion in JDHCPD's DHCP Relay Agent of Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) by sending a crafted DHCP packet to the device thereby crashing the jdhcpd DHCP service. This is typically configured for Broadband Subscriber Sessions. Continued receipt and processing of this crafted packet will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS: 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R2-S1, 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R2. This issue does not affect Junos OS Evolved.
A Missing Release of Memory after Effective Lifetime vulnerability in the Packet Forwarding Engine (PFE) of the Juniper Networks Junos OS on the MX Series platforms with Trio-based FPCs allows an unauthenticated, adjacent attacker to cause a Denial of Service (DoS). In case of channelized Modular Interface Cards (MICs), every physical interface flap operation will leak heap memory. Over a period of time, continuous physical interface flap operations causes local FPC to eventually run out of memory and crash. Below CLI command can be used to check the memory usage over a period of time: user@host> show chassis fpc Temp CPU Utilization (%) CPU Utilization (%) Memory Utilization (%) Slot State (C) Total Interrupt 1min 5min 15min DRAM (MB) Heap Buffer 0 Online 43 41 2 2048 49 14 1 Online 43 41 2 2048 49 14 2 Online 43 41 2 2048 49 14 This issue affects Junos OS on MX Series: * All versions before 21.2R3-S7, * from 21.4 before 21.4R3-S6, * from 22.1 before 22.1R3-S5, * from 22.2 before 22.2R3-S3, * from 22.3 before 22.3R3-S2, * from 22.4 before 22.4R3, * from 23.2 before 23.2R2, * from 23.4 before 23.4R2.
An Improper Input Validation vulnerability in the kernel of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, adjacent attacker to cause a Denial of Service (DoS). If the receipt of router advertisements is enabled on an interface and a specifically malformed RA packet is received, memory corruption will happen which leads to an rpd crash. This issue affects: Juniper Networks Junos OS 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S3; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2; 22.1 versions prior to 22.1R2. Juniper Networks Junos OS Evolved 20.3-EVO version 20.3R1-EVO and later versions; 20.4-EVO versions prior to 20.4R3-S6-EVO; 21.3-EVO versions prior to 21.3R3-EVO; 21.4-EVO versions prior to 21.4R2-EVO; 22.1-EVO versions prior to 22.1R2-EVO.
An Improper Input Validation vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an adjacent unauthenticated attacker to cause DoS (Denial of Service). If another router generates more than one specific valid OSPFv3 LSA then rpd will crash while processing these LSAs. This issue only affects systems configured with OSPFv3, while OSPFv2 is not affected. This issue affects: Juniper Networks Junos OS 19.2 versions prior to 19.2R3-S6; 19.3 version 19.3R2 and later versions; 19.4 versions prior to 19.4R2-S8, 19.4R3-S9; 20.1 version 20.1R1 and later versions; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S2; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3-S2; 21.4 versions prior to 21.4R2. Juniper Networks Junos OS Evolved All versions prior to 20.4R3-S5-EVO; 21.1-EVO versions prior to 21.1R3-S2-EVO; 21.2-EVO versions prior to 21.2R3-S1-EVO; 21.3-EVO versions prior to 21.3R3-S2-EVO; 21.4-EVO versions prior to 21.4R2-EVO; 22.1-EVO versions prior to 22.1R2-EVO; 22.2-EVO versions prior to 22.2R2-EVO. This issue does not affect Juniper Networks Junos OS 19.2 versions prior to 19.2R2.
An Improper Input Validation vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS and Junos OS Evolved allows an adjacent attacker to cause a PFE crash and thereby a Denial of Service (DoS). An FPC will crash and reboot after receiving a specific transit IPv6 packet over MPLS. Continued receipt of this packet will create a sustained Denial of Service (DoS) condition. This issue does not affect systems configured for IPv4 only. This issue affects: Juniper Networks Junos OS All versions prior to 12.3R12-S21; 15.1 versions prior to 15.1R7-S10; 17.3 versions prior to 17.3R3-S12; 18.3 versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S7, 19.3R3-S4; 19.4 versions prior to 19.4R3-S5; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R2-S2, 20.4R3; 21.1 versions prior to 21.1R2. Juniper Networks Junos OS Evolved All versions prior to 20.4R3-S3-EVO; 21.2 versions prior to 21.2R3-EVO; 21.3 versions prior to 21.3R2-S1-EVO, 21.3R3-EVO; 21.4 versions prior to 21.4R2-EVO.
An Improper Validation of Specified Type of Input vulnerability in the kernel of Juniper Networks Junos OS allows an unauthenticated adjacent attacker to trigger a Missing Release of Memory after Effective Lifetime vulnerability. Continued exploitation of this vulnerability will eventually lead to an FPC reboot and thereby a Denial of Service (DoS). This issue affects: Juniper Networks Junos OS on vMX and MX150: All versions prior to 19.2R1-S8, 19.2R3-S4; 19.3 versions prior to 19.3R3-S5; 19.4 versions prior to 19.4R2-S5, 19.4R3-S6; 20.1 versions prior to 20.1R3-S2; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2-S1, 21.1R3; 21.2 versions prior to 21.2R1-S1, 21.2R2; 21.3 versions prior to 21.3R1-S1, 21.3R2.
On QFX10000 Series devices using Juniper Networks Junos OS when configured as transit IP/MPLS penultimate hop popping (PHP) nodes with link aggregation group (LAG) interfaces, an Improper Validation of Specified Index, Position, or Offset in Input weakness allows an attacker sending certain IP packets to cause multiple interfaces in the LAG to detach causing a Denial of Service (DoS) condition. Continued receipt and processing of these packets will sustain the Denial of Service. This issue affects IPv4 and IPv6 packets. Packets of either type can cause and sustain the DoS event. These packets can be destined to the device or be transit packets. On devices such as the QFX10008 with line cards, line cards can be restarted to restore service. On devices such as the QFX10002 you can restart the PFE service, or reboot device to restore service. This issue affects: Juniper Networks Junos OS on QFX10000 Series: All versions prior to 15.1R7-S11; 18.4 versions prior to 18.4R2-S10, 18.4R3-S10; 19.1 versions prior to 19.1R3-S8; 19.2 versions prior to 19.2R3-S4; 19.3 versions prior to 19.3R3-S5; 19.4 versions prior to 19.4R2-S6, 19.4R3-S7; 20.1 versions prior to 20.1R3-S3; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S2; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S1. An indicator of compromise may be seen by issuing the command: request pfe execute target fpc0 command "show jspec pechip[3] registers ps l2_node 10" timeout 0 | refresh 1 | no-more and reviewing for backpressured output; for example: GOT: 0x220702a8 pe.ps.l2_node[10].pkt_cnt 00000076 GOT: 0x220702b4 pe.ps.l2_node[10].backpressured 00000002 <<<< STICKS HERE and requesting detail on the pepic wanio: request pfe execute target fpc0 command "show pepic 0 wanio-info" timeout 0 | no-more | match xe-0/0/0:2 GOT: 3 xe-0/0/0:2 10 6 3 0 1 10 189 10 0x6321b088 <<< LOOK HERE as well as looking for tail drops looking at the interface queue, for example: show interfaces queue xe-0/0/0:2 resulting in: Transmitted: Total-dropped packets: 1094137 0 pps << LOOK HERE
An Uncontrolled Resource Consumption vulnerability in the handling of IPv6 neighbor state change events in Juniper Networks Junos OS allows an adjacent attacker to cause a memory leak in the Flexible PIC Concentrator (FPC) of an ACX5448 router. The continuous flapping of an IPv6 neighbor with specific timing will cause the FPC to run out of resources, leading to a Denial of Service (DoS) condition. Once the condition occurs, further packet processing will be impacted, creating a sustained Denial of Service (DoS) condition, requiring a manual PFE restart to restore service. The following error messages will be seen after the FPC resources have been exhausted: fpc0 DNX_NH::dnx_nh_tag_ipv4_hw_install(),3135: dnx_nh_tag_ipv4_hw_install: BCM L3 Egress create object failed for NH 602 (-14:No resources for operation), BCM NH Params: unit:0 Port:41, L3_INTF:0 Flags: 0x40 fpc0 DNX_NH::dnx_nh_tag_ipv4_hw_install(),3135: dnx_nh_tag_ipv4_hw_install: BCM L3 Egress create object failed for NH 602 (-14:No resources for operation), BCM NH Params: unit:0 Port:41, L3_INTF:0 Flags: 0x40 fpc0 DNX_NH::dnx_nh_tag_ipv4_hw_install(),3135: dnx_nh_tag_ipv4_hw_install: BCM L3 Egress create object failed for NH 602 (-14:No resources for operation), BCM NH Params: unit:0 Port:41, L3_INTF:0 Flags: 0x40 fpc0 DNX_NH::dnx_nh_tag_ipv4_hw_install(),3135: dnx_nh_tag_ipv4_hw_install: BCM L3 Egress create object failed for NH 602 (-14:No resources for operation), BCM NH Params: unit:0 Port:41, L3_INTF:0 Flags: 0x40 This issue only affects the ACX5448 router. No other products or platforms are affected by this vulnerability. This issue affects Juniper Networks Junos OS on ACX5448: 18.4 versions prior to 18.4R3-S10; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R1-S8, 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S3, 19.4R2-S2, 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R1-S1, 20.2R2.
An Improper Input Validation vulnerability in the Juniper DHCP daemon (jdhcpd) of Juniper Networks Junos OS allows an adjacent unauthenticated attacker to cause a crash of jdhcpd and thereby a Denial of Service (DoS). If a device is configured as DHCPv6 local server and persistent storage is enabled, jdhcpd will crash when receiving a specific DHCPv6 message. This issue affects: Juniper Networks Junos OS All versions prior to 15.1R7-S11; 18.4 versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S8, 19.2R3-S3; 19.4 versions prior to 19.4R3-S5; 20.1 versions prior to 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2; 21.2 versions prior to 21.2R2.
An Improper Validation of Syntactic Correctness of Input vulnerability in the Juniper DHCP daemon (jdhcpd) of Juniper Networks Junos OS allows an adjacent unauthenticated attacker sending a malformed DHCP packet to cause a crash of jdhcpd and thereby a Denial of Service (DoS). If option-82 is configured in a DHCP snooping / -security scenario, jdhcpd crashes if a specific malformed DHCP request packet is received. The DHCP functionality is impacted while jdhcpd restarts, and continued exploitation of the vulnerability will lead to the unavailability of the DHCP service and thereby a sustained DoS. This issue affects Juniper Networks Junos OS 13.2 version 13.2R1 and later versions prior to 15.1R7-S11; 18.3 versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R2-S9, 18.4R3-S10; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S8, 19.2R3-S4; 19.3 versions prior to 19.3R2-S7, 19.3R3-S4; 19.4 versions prior to 19.4R3-S6; 20.1 versions prior to 20.1R3-S3; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2-S1, 21.1R3; 21.2 versions prior to 21.2R1-S1, 21.2R2. This issue does not affect Juniper Networks Junos OS version 12.3R12 and prior versions.
A Missing Release of Memory after Effective Lifetime vulnerability in the Layer-2 control protocols daemon (l2cpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated adjacent attacker to cause a memory leak. Continued exploitation can lead to memory exhaustion and thereby a Denial of Service (DoS). This issue occurs when specific LLDP packets are received. The impact of the l2cpd cores is that if any of the stp protocols (rstp, mstp or vstp) is used then stp re-converges and traffic loss will occur during that time. Also if any services depend on LLDP state (like PoE or VoIP device recognition) then these will also be affected. The memory utilization of the L2CPd process can be monitored with the following command: user@host> show system processes extensive | match l2cpd 1234 root 52 0 521M 43412K RUN 1 4:02 34.47% l2cpd This issue affects: Juniper Networks Junos OS 18.4 version 18.4R2-S4 and later versions prior to 18.4R2-S10. 19.2 versions prior to 19.2R1-S8, 19.2R3-S4; 19.3 versions prior to 19.3R3-S5; 19.4 versions prior to 19.4R3-S7; 20.1 versions prior to 20.1R3-S3; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2-S2, 21.1R3; 21.2 versions prior to 21.2R2; Juniper Networks Junos OS Evolved All versions prior to 20.4R3-S2-EVO; 21.1 version 21.1R1-EVO and later versions; 21.2 versions prior to 21.2R2-EVO. This issue does not affect: Juniper Networks Junos OS 19.1 version 19.1R1 and later versions.
A Missing Release of Memory after Effective Lifetime vulnerability in Flexible PIC Concentrator (FPC) of Juniper Networks Junos OS allows an adjacent, unauthenticated attacker from the same shared physical or logical network, to cause a heap memory leak and leading to FPC crash. On all Junos PTX Series and QFX10000 Series, when specific EVPN VXLAN Multicast packets are processed, an FPC heap memory leak is observed. The FPC memory usage can be monitored using the CLI command "show heap extensive". Following is an example output. ID Base Total(b) Free(b) Used(b) % Name Peak used % -- -------- --------- --------- --------- --- ----------- ----------- 0 37dcf000 3221225472 1694526368 1526699104 47 Kernel 47 1 17dcf000 1048576 1048576 0 0 TOE DMA 0 2 17ecf000 1048576 1048576 0 0 DMA 0 3 17fcf000 534773760 280968336 253805424 47 Packet DMA 47 This issue affects: Juniper Networks Junos OS PTX Series and QFX10000 Series 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S6; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2; 22.2 versions prior to 22.2R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.1R1 on PTX Series and QFX10000 Series.
A Improper Validation of Specified Index, Position, or Offset in Input vulnerability in the Juniper DHCP daemon (jdhcpd) of Juniper Networks Junos OS allows an adjacent unauthenticated attacker to cause a crash of jdhcpd and thereby a Denial of Service (DoS). In a scenario where DHCP relay or local server is configured the problem can be triggered if a DHCPv4 packet with specific options is received leading to a corruption of the options read from the packet. This corruption can then lead to jdhcpd crash and restart. This issue affects: Juniper Networks Junos OS 17.4R1 and later versions prior to 18.4R3-S10; 19.1 versions prior to 19.1R3-S7; 19.2 versions prior to 19.2R1-S8, 19.2R3-S4; 19.3 versions prior to 19.3R3-S4; 19.4 versions prior to 19.4R3-S6; 20.1 versions prior to 20.1R3-S2; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S2; 20.4 versions prior to 20.4R3-S1; 21.1 versions prior to 21.1R2-S2, 21.1R3; 21.2 versions prior to 21.2R1-S2, 21.2R2, 21.2R3; 21.3 versions prior to 21.3R1-S1, 21.3R2.
A Missing Release of Memory after Effective Lifetime vulnerability in the Juniper Networks Junos OS on MX Series platforms with MPC10/MPC11 line cards, allows an unauthenticated adjacent attacker to cause a Denial of Service (DoS). Devices are only vulnerable when the Suspicious Control Flow Detection (scfd) feature is enabled. Upon enabling this specific feature, an attacker sending specific traffic is causing memory to be allocated dynamically and it is not freed. Memory is not freed even after deactivating this feature. Sustained processing of such traffic will eventually lead to an out of memory condition that prevents all services from continuing to function, and requires a manual restart to recover. The FPC memory usage can be monitored using the CLI command "show chassis fpc". On running the above command, the memory of AftDdosScfdFlow can be observed to detect the memory leak. This issue affects Juniper Networks Junos OS on MX Series: All versions prior to 20.2R3-S5; 20.3 version 20.3R1 and later versions.
A Missing Release of Memory after Effective Lifetime vulnerability in the kernel of Juniper Networks Junos OS allows an unauthenticated, adjacent attacker to cause a Denial of Service (DoS). In an MPLS scenario specific packets destined to an Integrated Routing and Bridging (irb) interface of the device will cause a buffer (mbuf) to leak. Continued receipt of these specific packets will eventually cause a loss of connectivity to and from the device, and requires a reboot to recover. These mbufs can be monitored by using the CLI command 'show system buffers': user@host> show system buffers 783/1497/2280 mbufs in use (current/cache/total) user@host> show system buffers 793/1487/2280 mbufs in use (current/cache/total) <<<<<< mbuf usage increased This issue affects Juniper Networks Junos OS: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R3-S9; 20.1 version 20.1R1 and later versions; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S2; 21.3 versions prior to 21.3R3-S1; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2.
A Missing Release of Memory after Effective Lifetime vulnerability in the kernel of Juniper Networks Junos OS and Junos OS Evolved allows an adjacent, unauthenticated attacker to cause a Denial of Service (DoS). In a segment-routing scenario with OSPF as IGP, when a peer interface continuously flaps, next-hop churn will happen and a continuous increase in Routing Protocol Daemon (rpd) memory consumption will be observed. This will eventually lead to an rpd crash and restart when the memory is full. The memory consumption can be monitored using the CLI command "show task memory detail" as shown in the following example: user@host> show task memory detail | match "RT_NEXTHOPS_TEMPLATE|RT_TEMPLATE_BOOK_KEE" RT_NEXTHOPS_TEMPLATE 1008 1024 T 50 51200 50 51200 RT_NEXTHOPS_TEMPLATE 688 768 T 50 38400 50 38400 RT_NEXTHOPS_TEMPLATE 368 384 T 412330 158334720 412330 158334720 RT_TEMPLATE_BOOK_KEE 2064 2560 T 33315 85286400 33315 85286400 user@host> show task memory detail | match "RT_NEXTHOPS_TEMPLATE|RT_TEMPLATE_BOOK_KEE" RT_NEXTHOPS_TEMPLATE 1008 1024 T 50 51200 50 51200 RT_NEXTHOPS_TEMPLATE 688 768 T 50 38400 50 38400 RT_NEXTHOPS_TEMPLATE 368 384 T 419005 160897920 419005 160897920 <=== RT_TEMPLATE_BOOK_KEE 2064 2560 T 39975 102336000 39975 10233600 <=== This issue affects: Juniper Networks Junos OS All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R2-S8, 19.4R3-S9; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S2; 21.3 versions prior to 21.3R3-S1; 21.4 versions prior to 21.4R2-S1, 21.4R3; 22.1 versions prior to 22.1R2. Juniper Networks Junos OS Evolved All versions prior to 20.4R3-S4-EVO; 21.4 versions prior to 21.4R2-S1-EVO, 21.4R3-EVO; 22.1 versions prior to 22.1R2-EVO.
A Missing Release of Memory after Effective Lifetime vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows an adjacent, unauthenticated attacker to cause a Denial of Service (DoS). PTX3000, PTX5000, QFX10000, PTX1000, PTX10002, and PTX10004, PTX10008 and PTX10016 with LC110x FPCs do not support certain flow-routes. Once a flow-route is received over an established BGP session and an attempt is made to install the resulting filter into the PFE, FPC heap memory is leaked. The FPC heap memory can be monitored using the CLI command "show chassis fpc". The following syslog messages can be observed if the respective filter derived from a flow-route cannot be installed. expr_dfw_sfm_range_add:661 SFM packet-length Unable to get a sfm entry for updating the hw expr_dfw_hw_sfm_add:750 Unable to add the filter secondarymatch to the hardware expr_dfw_base_hw_add:52 Failed to add h/w sfm data. expr_dfw_base_hw_create:114 Failed to add h/w data. expr_dfw_base_pfe_inst_create:241 Failed to create base inst for sfilter 0 on PFE 0 for __flowspec_default_inet__ expr_dfw_flt_inst_change:1368 Failed to create __flowspec_default_inet__ on PFE 0 expr_dfw_hw_pgm_fnum:465 dfw_pfe_inst_old not found for pfe_index 0! expr_dfw_bp_pgm_flt_num:548 Failed to pgm bind-point in hw: generic failure expr_dfw_bp_topo_handler:1102 Failed to program fnum. expr_dfw_entry_process_change:679 Failed to change instance for filter __flowspec_default_inet__. This issue affects Juniper Networks Junos OS: on PTX1000, PTX10002, and PTX10004, PTX10008 and PTX10016 with LC110x FPCs: * All versions prior to 20.4R3-S5; * 21.1 versions prior to 21.1R3-S4; * 21.2 versions prior to 21.2R3-S2; * 21.3 versions prior to 21.3R3; * 21.4 versions prior to 21.4R2-S2, 21.4R3; * 22.1 versions prior to 22.1R1-S2, 22.1R2. on PTX3000, PTX5000, QFX10000: * All versions prior to 20.4R3-S8; * 21.1 version 21.1R1 and later versions; * 21.2 versions prior to 21.2R3-S6; * 21.3 versions prior to 21.3R3-S5; * 21.4 versions prior to 21.4R3-S4; * 22.1 versions prior to 22.1R3-S3 * 22.2 versions prior to 22.2R3-S1 * 22.3 versions prior to 22.3R2-S2, 22.3R3 * 22.4 versions prior to 22.4R2.
Due to a new NDP proxy feature for EVPN leaf nodes introduced in Junos OS 17.4, crafted NDPv6 packets could transit a Junos device configured as a Broadband Network Gateway (BNG) and reach the EVPN leaf node, causing a stale MAC address entry. This could cause legitimate traffic to be discarded, leading to a Denial of Service (DoS) condition. This issue only affects Junos OS 17.4 and later releases. Prior releases do not support this feature and are unaffected by this vulnerability. This issue only affects IPv6. IPv4 ARP proxy is unaffected by this vulnerability. This issue affects Juniper Networks Junos OS: 17.4 versions prior to 17.4R2-S9, 17.4R3 on MX Series; 18.1 versions prior to 18.1R3-S9 on MX Series; 18.2 versions prior to 18.2R2-S7, 18.2R3-S3 on MX Series; 18.2X75 versions prior to 18.2X75-D33, 18.2X75-D411, 18.2X75-D420, 18.2X75-D60 on MX Series; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3 on MX Series; 18.4 versions prior to 18.4R1-S5, 18.4R2-S2, 18.4R3 on MX Series; 19.1 versions prior to 19.1R1-S4, 19.1R2 on MX Series; 19.2 versions prior to 19.2R1-S3, 19.2R2 on MX Series.
A Missing Release of Memory after Effective Lifetime vulnerability in Juniper Networks Junos OS on MX Series allows an unauthenticated adjacent attacker to cause a Denial-of-Service (DoS). In a subscriber management scenario continuous subscriber logins will trigger a memory leak and eventually lead to an FPC crash and restart. This issue affects Junos OS on MX Series: * All version before 21.2R3-S6, * 21.4 versions before 21.4R3-S6, * 22.1 versions before 22.1R3-S5, * 22.2 versions before 22.2R3-S3, * 22.3 versions before 22.3R3-S2, * 22.4 versions before 22.4R3, * 23.2 versions before 23.2R2.
A Missing Release of Memory after Effective Lifetime vulnerability in the rtlogd process of Juniper Networks Junos OS on MX Series with SPC3 allows an unauthenticated, adjacent attacker to trigger internal events cause ( which can be done by repeated port flaps) to cause a slow memory leak, ultimately leading to a Denial of Service (DoS). Memory can only be recovered by manually restarting rtlogd process. The memory usage can be monitored using the below command. user@host> show system processes extensive | match rtlog This issue affects Junos OS on MX Series with SPC3 line card: * from 21.2R3 before 21.2R3-S8, * from 21.4R2 before 21.4R3-S6, * from 22.1 before 22.1R3-S5, * from 22.2 before 22.2R3-S3, * from 22.3 before 22.3R3-S2, * from 22.4 before 22.4R3-S1, * from 23.2 before 23.2R2, * from 23.4 before 23.4R2.
A Missing Release of Memory after Effective Lifetime vulnerability in the Periodic Packet Management Daemon (ppmd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated adjacent attacker to cause a Denial-of-Service (DoS). When a BFD session configured with authentication flaps, ppmd memory can leak. Whether the leak happens depends on a race condition which is outside the attackers control. This issue only affects BFD operating in distributed aka delegated (which is the default behavior) or inline mode. Whether the leak occurs can be monitored with the following CLI command: > show ppm request-queue FPC Pending-request fpc0 2 request-total-pending: 2 where a continuously increasing number of pending requests is indicative of the leak. This issue affects: Junos OS: * All versions before 21.2R3-S8, * 21.4 versions before 21.4R3-S7, * 22.1 versions before 22.1R3-S4, * 22.2 versions before 22.2R3-S4, * 22.3 versions before 22.3R3, * 22.4 versions before 22.4R2-S2, 22.4R3. Junos OS Evolved: * All versions before 21.2R3-S8-EVO, * 21.4-EVO versions before 21.4R3-S7-EVO, * 22.2-EVO versions before 22.2R3-S4-EVO, * 22.3-EVO versions before 22.3R3-EVO, * 22.4-EVO versions before 22.4R3-EVO.
On Juniper Networks MX series, receipt of a stream of specific Layer 2 frames may cause a memory leak resulting in the packet forwarding engine (PFE) on the line card to crash and restart, causing traffic interruption. By continuously sending this stream of specific layer 2 frame, an attacker connected to the same broadcast domain can repeatedly crash the PFE, causing a prolonged Denial of Service (DoS). This issue affects Juniper Networks Junos OS on MX Series: 17.2 versions prior to 17.2R3-S4; 17.2X75 versions prior to 17.2X75-D105.19; 17.3 versions prior to 17.3R3-S7; 17.4 versions prior to 17.4R1-S3, 17.4R2; 18.1 versions prior to 18.1R2. This issue does not affect Juniper Networks Junos OS releases prior to 17.2R1.
The kernel memory usage represented as "temp" via 'show system virtual-memory' may constantly increase when Integrated Routing and Bridging (IRB) is configured with multiple underlay physical interfaces, and one interface flaps. This memory leak can affect running daemons (processes), leading to an extended Denial of Service (DoS) condition. Usage of "temp" virtual memory, shown here by a constantly increasing value of outstanding Requests, can be monitored by executing the 'show system virtual-memory' command as shown below: user@junos> show system virtual-memory |match "fpc|type|temp" fpc0: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2023 431K - 10551 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 fpc1: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2020 431K - 6460 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 user@junos> show system virtual-memory |match "fpc|type|temp" fpc0: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2023 431K - 16101 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 fpc1: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2020 431K - 6665 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 user@junos> show system virtual-memory |match "fpc|type|temp" fpc0: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2023 431K - 21867 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 fpc1: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2020 431K - 6858 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S6; 17.1 versions prior to 17.1R2-S11, 17.1R3-S1; 17.2 versions prior to 17.2R2-S8, 17.2R3-S3; 17.2X75 versions prior to 17.2X75-D44; 17.3 versions prior to 17.3R2-S5, 17.3R3-S6; 17.4 versions prior to 17.4R2-S5, 17.4R3; 18.1 versions prior to 18.1R3-S7; 18.2 versions prior to 18.2R2-S5, 18.2R3; 18.2X75 versions prior to 18.2X75-D33, 18.2X75-D411, 18.2X75-D420, 18.2X75-D60; 18.3 versions prior to 18.3R1-S5, 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R2-S2, 18.4R3; 19.1 versions prior to 19.1R1-S3, 19.1R2; 19.2 versions prior to 19.2R1-S3, 19.2R2. This issue does not affect Juniper Networks Junos OS 12.3 and 15.1.
On Juniper Networks Junos OS and Junos OS Evolved platforms with EVPN configured, receipt of specific BGP packets causes a slow memory leak. If the memory is exhausted the rpd process might crash. If the issue occurs, the memory leak could be seen by executing the "show task memory detail | match policy | match evpn" command multiple times to check if memory (Alloc Blocks value) is increasing. root@device> show task memory detail | match policy | match evpn ------------------------ Allocator Memory Report ------------------------ Name | Size | Alloc DTXP Size | Alloc Blocks | Alloc Bytes | MaxAlloc Blocks | MaxAlloc Bytes Policy EVPN Params 20 24 3330678 79936272 3330678 79936272 root@device> show task memory detail | match policy | match evpn ------------------------ Allocator Memory Report ------------------------ Name | Size | Alloc DTXP Size | Alloc Blocks | Alloc Bytes | MaxAlloc Blocks | MaxAlloc Bytes Policy EVPN Params 20 24 36620255 878886120 36620255 878886120 This issue affects: Juniper Networks Junos OS 19.4 versions prior to 19.4R2; 20.1 versions prior to 20.1R1-S4, 20.1R2; Juniper Networks Junos OS Evolved: 19.4 versions; 20.1 versions prior to 20.1R1-S4-EVO, 20.1R2-EVO; 20.2 versions prior to 20.2R1-EVO; This issue does not affect: Juniper Networks Junos OS releases prior to 19.4R1. Juniper Networks Junos OS Evolved releases prior to 19.4R1-EVO.
When an MX Series Broadband Remote Access Server (BRAS) is configured as a Broadband Network Gateway (BNG) with DHCPv6 enabled, jdhcpd might crash when receiving a specific crafted DHCP response message on a subscriber interface. The daemon automatically restarts without intervention, but continuous receipt of specific crafted DHCP messages will repeatedly crash jdhcpd, leading to an extended Denial of Service (DoS) condition. This issue only affects systems configured with DHCPv6 enabled. DHCPv4 is unaffected by this issue. This issue affects Juniper Networks Junos OS: 15.1 versions prior to 15.1R7-S5 on MX Series; 16.1 versions prior to 16.1R7-S5 on MX Series; 16.2 versions prior to 16.2R2-S10 on MX Series; 17.1 versions prior to 17.1R3-S1 on MX Series; 17.2 versions prior to 17.2R3-S2 on MX Series; 17.3 versions prior to 17.3R3-S6 on MX Series; 17.4 versions prior to 17.4R2-S5, 17.4R3 on MX Series; 18.1 versions prior to 18.1R3-S6 on MX Series; 18.2 versions prior to 18.2R2-S4, 18.2R3 on MX Series; 18.2X75 versions prior to 18.2X75-D50 on MX Series; 18.3 versions prior to 18.3R1-S5, 18.3R3 on MX Series; 18.4 versions prior to 18.4R2 on MX Series; 19.1 versions prior to 19.1R1-S2, 19.1R2 on MX Series.
The SRX flowd process, responsible for packet forwarding, may crash and restart when processing specific multicast packets. By continuously sending the specific multicast packets, an attacker can repeatedly crash the flowd process causing a sustained Denial of Service. This issue affects Juniper Networks Junos OS on SRX Series: 12.3X48 versions prior to 12.3X48-D90; 15.1X49 versions prior to 15.1X49-D180; 17.3 versions; 17.4 versions prior to 17.4R2-S5, 17.4R3; 18.1 versions prior to 18.1R3-S6; 18.2 versions prior to 18.2R2-S4, 18.2R3; 18.3 versions prior to 18.3R2-S1, 18.3R3; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R1-S1, 19.1R2.
The Junos OS kernel crashes after processing a specific incoming packet to the out of band management interface (such as fxp0, me0, em0, vme0) destined for another address. By continuously sending this type of packet, an attacker can repeatedly crash the kernel causing a sustained Denial of Service. Affected releases are Juniper Networks Junos OS: 17.2 versions prior to 17.2R1-S7, 17.2R3; 17.3 versions prior to 17.3R3-S3; 17.4 versions prior to 17.4R1-S4, 17.4R2; 17.2X75 versions prior to 17.2X75-D110; 18.1 versions prior to 18.1R2.
A vulnerability in the pfe-chassisd Chassis Manager (CMLC) daemon of Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) to the EX4300 when specific valid broadcast packets create a broadcast storm condition when received on the me0 interface of the EX4300 Series device. A reboot of the device is required to restore service. Continued receipt of these valid broadcast packets will create a sustained Denial of Service (DoS) against the device. Affected releases are Juniper Networks Junos OS: 16.1 versions above and including 16.1R1 prior to 16.1R7-S5; 17.1 versions prior to 17.1R3; 17.2 versions prior to 17.2R3; 17.3 versions prior to 17.3R3-S2; 17.4 versions prior to 17.4R2; 18.1 versions prior to 18.1R3; 18.2 versions prior to 18.2R2.
Receipt of a specific link-local IPv6 packet destined to the RE may cause the system to crash and restart (vmcore). By continuously sending a specially crafted IPv6 packet, an attacker can repeatedly crash the system causing a prolonged Denial of Service (DoS). This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R6-S2, 16.1R7; 16.2 versions prior to 16.2R2-S10; 17.1 versions prior to 17.1R3. This issue does not affect Juniper Networks Junos OS version 15.1 and prior versions.
An Improper Handling of Missing Values vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows an adjacent, unauthenticated attacker to cause a dcpfe process core and thereby a Denial of Service (DoS). Continued receipt of these specific frames will cause a sustained Denial of Service condition. This issue occurs when a specific malformed ethernet frame is received. This issue affects Juniper Networks Junos OS on QFX10000 Series, PTX1000 Series Series: All versions prior to 19.4R3-S10; 20.1 version 20.1R1 and later versions; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3-S1; 22.1 versions prior to 22.1R2-S1, 22.1R3; 22.2 versions prior to 22.2R1-S2, 22.2R2.
Crafted packets destined to the management interface (fxp0) of an SRX340 or SRX345 services gateway may create a denial of service (DoS) condition due to buffer space exhaustion. This issue only affects the SRX340 and SRX345 services gateways. No other products or platforms are affected by this vulnerability. Affected releases are Juniper Networks Junos OS: 15.1X49 versions prior to 15.1X49-D160 on SRX340/SRX345; 17.3 on SRX340/SRX345; 17.4 versions prior to 17.4R2-S3, 17.4R3 on SRX340/SRX345; 18.1 versions prior to 18.1R3-S1 on SRX340/SRX345; 18.2 versions prior to 18.2R2 on SRX340/SRX345; 18.3 versions prior to 18.3R1-S2, 18.3R2 on SRX340/SRX345. This issue does not affect Junos OS releases prior to 15.1X49 on any platform.
An Improper Check or Handling of Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, adjacent attacker to cause a Denial of Service (DoS). If an attacker sends a specific MPLS packet, which upon processing, causes an internal loop, that leads to a PFE crash and restart. Continued receipt of these packets leads to a sustained Denial of Service (DoS) condition. Circuit cross-connect (CCC) needs to be configured on the device for it to be affected by this issue. This issue only affects MX Series with MPC10, MPC11, LC9600, and MX304. This issue affects: Juniper Networks Junos OS 21.4 versions from 21.4R3 earlier than 21.4R3-S5; 22.2 versions from 22.2R2 earlier than 22.2R3-S2; 22.3 versions from 22.3R1 earlier than 22.3R2-S2; 22.3 versions from 22.3R3 earlier than 22.3R3-S1 22.4 versions from 22.4R1 earlier than 22.4R2-S2, 22.4R3; 23.2 versions earlier than 23.2R1-S1, 23.2R2.
An Improper Handling of Exceptional Conditions vulnerability in the broadband edge subscriber management daemon (bbe-smgd) of Juniper Networks Junos OS on MX Series allows an attacker directly connected to the vulnerable system who repeatedly flaps DHCP subscriber sessions to cause a slow memory leak, ultimately leading to a Denial of Service (DoS). Memory can only be recovered by manually restarting bbe-smgd. This issue only occurs if BFD liveness detection for DHCP subscribers is enabled. Systems without BFD liveness detection enabled are not vulnerable to this issue. Indication of the issue can be observed by periodically executing the 'show system processes extensive' command, which will indicate an increase in memory allocation for bbe-smgd. A small amount of memory is leaked every time a DHCP subscriber logs in, which will become visible over time, ultimately leading to memory starvation. user@junos> show system processes extensive | match bbe-smgd 13071 root 24 0 415M 201M select 0 0:41 7.28% bbe-smgd{bbe-smgd} 13071 root 20 0 415M 201M select 1 0:04 0.00% bbe-smgd{bbe-smgd} ... user@junos> show system processes extensive | match bbe-smgd 13071 root 20 0 420M 208M select 0 4:33 0.10% bbe-smgd{bbe-smgd} 13071 root 20 0 420M 208M select 0 0:12 0.00% bbe-smgd{bbe-smgd} ... This issue affects Juniper Networks Junos OS on MX Series: * All versions earlier than 20.4R3-S9; * 21.2 versions earlier than 21.2R3-S7; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R3-S4; * 22.2 versions earlier than 22.2R3-S3; * 22.3 versions earlier than 22.3R3-S2; * 22.4 versions earlier than 22.4R2-S2, 22.4R3; * 23.2 versions earlier than 23.2R1-S1, 23.2R2.
An Improper Neutralization of Equivalent Special Elements vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on PTX Series allows a unauthenticated, adjacent attacker to cause a Denial of Service (DoS). When MPLS packets are meant to be sent to a flexible tunnel interface (FTI) and if the FTI tunnel is down, these will hit the reject NH, due to which the packets get sent to the CPU and cause a host path wedge condition. This will cause the FPC to hang and requires a manual restart to recover. Please note that this issue specifically affects PTX1000, PTX3000, PTX5000 with FPC3, PTX10002-60C, and PTX10008/16 with LC110x. Other PTX Series devices and Line Cards (LC) are not affected. The following log message can be seen when the issue occurs: Cmerror Op Set: Host Loopback: HOST LOOPBACK WEDGE DETECTED IN PATH ID <id> (URI: /fpc/<fpc>/pfe/<pfe>/cm/<cm>/Host_Loopback/<cm>/HOST_LOOPBACK_MAKE_CMERROR_ID[<id>]) This issue affects Juniper Networks Junos OS: * All versions earlier than 20.4R3-S8; * 21.1 versions earlier than 21.1R3-S4; * 21.2 versions earlier than 21.2R3-S6; * 21.3 versions earlier than 21.3R3-S3; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R2-S2, 22.1R3; * 22.2 versions earlier than 22.2R2-S1, 22.2R3.
An Exposure of Resource to Wrong Sphere vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on SRX 300 Series allows an unauthenticated, adjacent attacker to cause a Denial of Service (DoS). Specific valid link-local traffic is not blocked on ports in STP blocked state but is instead sent to the control plane of the device. This leads to excessive resource consumption and in turn severe impact on all control and management protocols of the device. This issue affects Juniper Networks Junos OS: * 21.2 version 21.2R3-S3 and later versions earlier than 21.2R3-S6; * 22.1 version 22.1R3 and later versions earlier than 22.1R3-S4; * 22.2 version 22.2R2 and later versions earlier than 22.2R3-S2; * 22.3 version 22.3R2 and later versions earlier than 22.3R3-S1; * 22.4 versions earlier than 22.4R2-S2, 22.4R3; * 23.2 versions earlier than 23.2R1-S1, 23.2R2. This issue does not affect Juniper Networks Junos OS 21.4R1 and later versions of 21.4.
An Access of Memory Location After End of Buffer vulnerability in the Layer-2 Control Protocols Daemon (l2cpd) of Juniper Networks Junos OS and Junos OS Evolved allows an adjacent, unauthenticated attacker to cause Denial of Service (DoS). On all Junos OS and Junos OS Evolved platforms, when LLDP is enabled on a specific interface, and a malformed LLDP packet is received, l2cpd crashes and restarts. The impact of the l2cpd crash is reinitialization of STP protocols (RSTP, MSTP or VSTP), and MVRP and ERP. Also, if any services depend on LLDP state (like PoE or VoIP device recognition), then these will also be affected. This issue affects: Junos OS: * from 21.4 before 21.4R3-S4, * from 22.1 before 22.1R3-S4, * from 22.2 before 22.2R3-S2, * from 22.3 before 22.3R2-S2, 22.3R3-S1, * from 22.4 before 22.4R3, * from 23.2 before 23.2R2. Junos OS Evolved: * from 21.4-EVO before 21.4R3-S5-EVO, * from 22.1-EVO before 22.1R3-S4-EVO, * from 22.2-EVO before 22.2R3-S2-EVO, * from 22.3-EVO before 22.3R2-S2-EVO, 22.3R3-S1-EVO, * from 22.4-EVO before 22.4R3-EVO, * from 23.2-EVO before 23.2R2-EVO. This issue does not affect: * Junos OS versions prior to 21.4R1; * Junos OS Evolved versions prior to 21.4R1-EVO.
An Incomplete Cleanup vulnerability in Nonstop active routing (NSR) component of Juniper Networks Junos OS allows an adjacent, unauthenticated attacker to cause memory leak leading to Denial of Service (DoS). On all Junos OS platforms, when NSR is enabled, a BGP flap will cause memory leak. A manual reboot of the system will restore the services. Note: NSR is not supported on the SRX Series and is therefore not affected by this vulnerability. The memory usage can be monitored using the below commands. user@host> show chassis routing-engine no-forwarding user@host> show system memory | no-more This issue affects: Juniper Networks Junos OS * 21.2 versions earlier than 21.2R3-S5; * 21.3 versions earlier than 21.3R3-S4; * 21.4 versions earlier than 21.4R3-S4; * 22.1 versions earlier than 22.1R3-S2; * 22.2 versions earlier than 22.2R3-S2; * 22.3 versions earlier than 22.3R2-S1, 22.3R3; * 22.4 versions earlier than 22.4R1-S2, 22.4R2. This issue does not affect Junos OS versions earlier than 20.4R3-S7.
An Improper Handling of Length Parameter Inconsistency vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a logically adjacent BGP peer sending a specifically malformed BGP packet to cause rpd to crash and restart, resulting in a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. Only systems configured for Ethernet Virtual Private Networking (EVPN) signaling are vulnerable to this issue. This issue affects iBGP and eBGP, and both IPv4 and IPv6 are affected by this vulnerability.This issue affects: Junos OS: * all versions before 21.4R3-S11, * from 22.2 before 22.2R3-S7, * from 22.4 before 22.4R3-S7, * from 23.2 before 23.2R2-S4, * from 23.4 before 23.4R2-S5, * from 24.2 before 24.2R2-S1, * from 24.4 before 24.4R1-S3, 24.4R2; Junos OS Evolved: * all versions before 22.2R3-S7-EVO, * from 22.4-EVO before 22.4R3-S7-EVO, * from 23.2-EVO before 23.2R2-S4-EVO, * from 23.4-EVO before 23.4R2-S5-EVO, * from 24.2-EVO before 24.2R2-S1-EVO, * from 24.4-EVO before 24.4R1-S3-EVO, 24.4R2-EVO.