A vulnerability in the Rate Limiting Network Address Translation (NAT) feature of Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause high CPU utilization in the Cisco QuantumFlow Processor of an affected device, resulting in a denial of service (DoS) condition. This vulnerability is due to mishandling of the rate limiting feature within the QuantumFlow Processor. An attacker could exploit this vulnerability by sending large amounts of traffic that would be subject to NAT and rate limiting through an affected device. A successful exploit could allow the attacker to cause the QuantumFlow Processor utilization to reach 100 percent on the affected device, resulting in a DoS condition.
A vulnerability in the RADIUS feature of Cisco Identity Services Engine (ISE) could allow an unauthenticated, remote attacker to cause the affected system to stop processing RADIUS packets. This vulnerability is due to improper handling of certain RADIUS requests. An attacker could exploit this vulnerability by attempting to authenticate to a network or a service where the access server is using Cisco ISE as the RADIUS server. A successful exploit could allow the attacker to cause Cisco ISE to stop processing RADIUS requests, causing authentication/authorization timeouts, which would then result in legitimate requests being denied access. Note: To recover the ability to process RADIUS packets, a manual restart of the affected Policy Service Node (PSN) is required. See the Details section for more information.
A vulnerability in the DNS application layer gateway (ALG) functionality that is used by Network Address Translation (NAT) in Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause an affected device to reload. This vulnerability is due to a logic error that occurs when an affected device inspects certain TCP DNS packets. An attacker could exploit this vulnerability by sending crafted DNS packets through the affected device that is performing NAT for DNS packets. A successful exploit could allow the attacker to cause the device to reload, resulting in a denial of service (DoS) condition on the affected device. Note: This vulnerability can be exploited only by sending IPv4 TCP packets through an affected device. This vulnerability cannot be exploited by sending IPv6 traffic.
A vulnerability in the data plane microcode of Lightspeed-Plus line cards for Cisco ASR 9000 Series Aggregation Services Routers could allow an unauthenticated, remote attacker to cause the line card to reset. This vulnerability is due to the incorrect handling of malformed packets that are received on the Lightspeed-Plus line cards. An attacker could exploit this vulnerability by sending a crafted IPv4 or IPv6 packet through an affected device. A successful exploit could allow the attacker to cause the Lightspeed-Plus line card to reset, resulting in a denial of service (DoS) condition for any traffic that traverses that line card.
A vulnerability in IP ingress packet processing of the Cisco Embedded Wireless Controller with Catalyst Access Points Software could allow an unauthenticated, remote attacker to cause the device to reload unexpectedly, causing a denial of service (DoS) condition. The device may experience a performance degradation in traffic processing or high CPU usage prior to the unexpected reload. This vulnerability is due to improper rate limiting of IP packets to the management interface. An attacker could exploit this vulnerability by sending a steady stream of IP traffic at a high rate to the management interface of the affected device. A successful exploit could allow the attacker to cause the device to reload.
A vulnerability in the bidirectional forwarding detection (BFD) hardware offload feature of Cisco IOS XR Software for Cisco ASR 9000 Series Aggregation Services Routers, ASR 9902 Compact High-Performance Routers, and ASR 9903 Compact High-Performance Routers could allow an unauthenticated, remote attacker to cause a line card to reset, resulting in a denial of service (DoS) condition. This vulnerability is due to the incorrect handling of malformed BFD packets that are received on line cards where the BFD hardware offload feature is enabled. An attacker could exploit this vulnerability by sending a crafted IPv4 BFD packet to an affected device. A successful exploit could allow the attacker to cause line card exceptions or a hard reset, resulting in loss of traffic over that line card while the line card reloads.
A vulnerability in the hardware-based SSL/TLS cryptography functionality of Cisco Adaptive Security Appliance (ASA) Software and Cisco Firepower Threat Defense (FTD) Software for Cisco Firepower 2100 Series Appliances could allow an unauthenticated, remote attacker to cause an affected device to reload unexpectedly, resulting in a denial of service (DoS) condition. This vulnerability is due to an implementation error within the cryptographic functions for SSL/TLS traffic processing when they are offloaded to the hardware. An attacker could exploit this vulnerability by sending a crafted stream of SSL/TLS traffic to an affected device. A successful exploit could allow the attacker to cause an unexpected error in the hardware-based cryptography engine, which could cause the device to reload.
Multiple vulnerabilities in the web-based user interface of certain Cisco Small Business Series Switches could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition or execute arbitrary code with root privileges on an affected device. These vulnerabilities are due to improper validation of requests that are sent to the web interface. For more information about these vulnerabilities, see the Details section of this advisory.
A vulnerability in the Multicast Leaf Recycle Elimination (mLRE) feature of Cisco IOS XE Software for Cisco ASR 1000 Series Aggregation Services Routers could allow an unauthenticated, remote attacker to cause the affected device to reload, resulting in a denial of service (DoS) condition. This vulnerability is due to incorrect handling of certain IPv6 multicast packets when they are fanned out more than seven times on an affected device. An attacker could exploit this vulnerability by sending a specific IPv6 multicast or IPv6 multicast VPN (MVPNv6) packet through the affected device. A successful exploit could allow the attacker to cause a reload of the affected device, resulting in a DoS condition.
Multiple vulnerabilities in the web-based user interface of certain Cisco Small Business Series Switches could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition or execute arbitrary code with root privileges on an affected device. These vulnerabilities are due to improper validation of requests that are sent to the web interface. For more information about these vulnerabilities, see the Details section of this advisory.
Multiple vulnerabilities in the web-based user interface of certain Cisco Small Business Series Switches could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition or execute arbitrary code with root privileges on an affected device. These vulnerabilities are due to improper validation of requests that are sent to the web interface. For more information about these vulnerabilities, see the Details section of this advisory.
A vulnerability in the internal packet processing of Cisco Firepower Threat Defense (FTD) Software for Cisco Firepower 2100 Series Firewalls could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to improper handling of certain packets when they are sent to the inspection engine. An attacker could exploit this vulnerability by sending a series of crafted packets to an affected device. A successful exploit could allow the attacker to deplete all 9,472 byte blocks on the device, resulting in traffic loss across the device or an unexpected reload of the device. If the device does not reload on its own, a manual reload of the device would be required to recover from this state.
A vulnerability in Application Quality of Experience (AppQoE) and Unified Threat Defense (UTD) on Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause an affected device to reload unexpectedly, resulting in a denial of service (DoS) condition. This vulnerability is due to the mishandling of a crafted packet stream through the AppQoE or UTD application. An attacker could exploit this vulnerability by sending a crafted packet stream through an affected device. A successful exploit could allow the attacker to cause the device to reload, resulting in a DoS condition.
A vulnerability in the processing of malformed Common Industrial Protocol (CIP) packets that are sent to Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause an affected device to unexpectedly reload, resulting in a denial of service (DoS) condition. This vulnerability is due to insufficient input validation during processing of CIP packets. An attacker could exploit this vulnerability by sending a malformed CIP packet to an affected device. A successful exploit could allow the attacker to cause the affected device to unexpectedly reload, resulting in a DoS condition.
A vulnerability in the AnyConnect SSL VPN feature of Cisco Adaptive Security Appliance (ASA) Software and Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to an implementation error within the SSL/TLS session handling process that can prevent the release of a session handler under specific conditions. An attacker could exploit this vulnerability by sending crafted SSL/TLS traffic to an affected device, increasing the probability of session handler leaks. A successful exploit could allow the attacker to eventually deplete the available session handler pool, preventing new sessions from being established and causing a DoS condition.
Multiple vulnerabilities in the web-based user interface of certain Cisco Small Business Series Switches could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition or execute arbitrary code with root privileges on an affected device. These vulnerabilities are due to improper validation of requests that are sent to the web interface. For more information about these vulnerabilities, see the Details section of this advisory.
A vulnerability in the networking component of Cisco access point (AP) software could allow an unauthenticated, remote attacker to cause a temporary disruption of service. This vulnerability is due to overuse of AP resources. An attacker could exploit this vulnerability by connecting to an AP on an affected device as a wireless client and sending a high rate of traffic over an extended period of time. A successful exploit could allow the attacker to cause the Datagram TLS (DTLS) session to tear down and reset, causing a denial of service (DoS) condition.
A vulnerability in the Layer 2 Tunneling Protocol (L2TP) feature of Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to improper handling of certain L2TP packets. An attacker could exploit this vulnerability by sending crafted L2TP packets to an affected device. A successful exploit could allow the attacker to cause the device to reload unexpectedly, resulting in a DoS condition. Note: Only traffic directed to the affected system can be used to exploit this vulnerability.
Multiple vulnerabilities in the web-based user interface of certain Cisco Small Business Series Switches could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition or execute arbitrary code with root privileges on an affected device. These vulnerabilities are due to improper validation of requests that are sent to the web interface. For more information about these vulnerabilities, see the Details section of this advisory.
A vulnerability in the IPv6 DHCP version 6 (DHCPv6) relay and server features of Cisco IOS and IOS XE Software could allow an unauthenticated, remote attacker to trigger a denial of service (DoS) condition. This vulnerability is due to insufficient validation of data boundaries. An attacker could exploit this vulnerability by sending crafted DHCPv6 messages to an affected device. A successful exploit could allow the attacker to cause the device to reload unexpectedly.
A vulnerability in the implementation of the IPv4 Virtual Fragmentation Reassembly (VFR) feature of Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to improper reassembly of large packets that occurs when VFR is enabled on either a tunnel interface or on a physical interface that is configured with a maximum transmission unit (MTU) greater than 4,615 bytes. An attacker could exploit this vulnerability by sending fragmented packets through a VFR-enabled interface on an affected device. A successful exploit could allow the attacker to cause the device to reload, resulting in a DoS condition.
Multiple vulnerabilities in the web-based user interface of certain Cisco Small Business Series Switches could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition or execute arbitrary code with root privileges on an affected device. These vulnerabilities are due to improper validation of requests that are sent to the web interface. For more information about these vulnerabilities, see the Details section of this advisory.
Multiple vulnerabilities in the web-based user interface of certain Cisco Small Business Series Switches could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition or execute arbitrary code with root privileges on an affected device. These vulnerabilities are due to improper validation of requests that are sent to the web interface. For more information about these vulnerabilities, see the Details section of this advisory.
A vulnerability in the Device Management Servlet application of Cisco BroadWorks Application Delivery Platform and Cisco BroadWorks Xtended Services Platform could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to improper input validation when parsing HTTP requests. An attacker could exploit this vulnerability by sending a sustained stream of crafted requests to an affected device. A successful exploit could allow the attacker to cause all subsequent requests to be dropped, resulting in a DoS condition.
Multiple vulnerabilities in the web-based user interface of certain Cisco Small Business Series Switches could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition or execute arbitrary code with root privileges on an affected device. These vulnerabilities are due to improper validation of requests that are sent to the web interface. For more information about these vulnerabilities, see the Details section of this advisory.
A vulnerability in ICMPv6 processing of Cisco Adaptive Security Appliance (ASA) Software and Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition. This vulnerability is due to improper processing of ICMPv6 messages. An attacker could exploit this vulnerability by sending crafted ICMPv6 messages to a targeted Cisco ASA or FTD system with IPv6 enabled. A successful exploit could allow the attacker to cause the device to reload, resulting in a DoS condition.
A vulnerability in the DNS inspection handler of Cisco Adaptive Security Appliance (ASA) Software and Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause a denial of service condition (DoS) on an affected device. This vulnerability is due to a lack of proper processing of incoming requests. An attacker could exploit this vulnerability by sending crafted DNS requests at a high rate to an affected device. A successful exploit could allow the attacker to cause the device to stop responding, resulting in a DoS condition.
A vulnerability in Cisco IOS XE Software for Cisco Catalyst 3650 and Catalyst 3850 Series Switches could allow an unauthenticated, remote attacker to cause an affected device to reload unexpectedly, resulting in a denial of service (DoS) condition. This vulnerability is due to improper resource management when processing traffic that is received on the management interface. An attacker could exploit this vulnerability by sending a high rate of traffic to the management interface. A successful exploit could allow the attacker to cause the device to reload, resulting in a DoS condition.
A vulnerability in the local interface of Cisco BroadWorks Network Server could allow an unauthenticated, remote attacker to exhaust system resources, causing a denial of service (DoS) condition. This vulnerability exists because rate limiting does not occur for certain incoming TCP connections. An attacker could exploit this vulnerability by sending a high rate of TCP connections to the server. A successful exploit could allow the attacker to cause TCP connection resources to grow rapidly until the Cisco BroadWorks Network Server becomes unusable. Note: To recover from this vulnerability, either Cisco BroadWorks Network Server software must be restarted or the Cisco BroadWorks Network Server node must be rebooted. For more information, see the section of this advisory. Cisco has released software updates that address this vulnerability. There are no workarounds that address this vulnerability.
A vulnerability in the connection handling function in Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to improper traffic handling when platform limits are reached. An attacker could exploit this vulnerability by sending a high rate of UDP traffic through an affected device. A successful exploit could allow the attacker to cause all new, incoming connections to be dropped, resulting in a DoS condition.
A vulnerability in dynamic access policies (DAP) functionality of Cisco Adaptive Security Appliance (ASA) Software and Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause an affected device to reload, resulting in a denial of service (DoS) condition. This vulnerability is due to improper processing of HostScan data received from the Posture (HostScan) module. An attacker could exploit this vulnerability by sending crafted HostScan data to an affected device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition. https://tools.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-asa-ftd-dap-dos-GhYZBxDU ["https://tools.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-asa-ftd-dap-dos-GhYZBxDU"] This advisory is part of the November 2022 release of the Cisco ASA, FTD, and FMC Security Advisory Bundled publication.
A vulnerability in the TCP proxy functionality of Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to trigger a denial of service (DoS) condition. This vulnerability is due to improper handling of TCP flows. An attacker could exploit this vulnerability by sending a crafted stream of TCP traffic through an affected device. A successful exploit could allow the attacker to cause the device to reload, resulting in a DoS condition.
A vulnerability in an API endpoint of multiple Cisco Unified Communications Products could allow an unauthenticated, remote attacker to cause high CPU utilization, which could impact access to the web-based management interface and cause delays with call processing. This API is not used for device management and is unlikely to be used in normal operations of the device. This vulnerability is due to improper API authentication and incomplete validation of the API request. An attacker could exploit this vulnerability by sending a crafted HTTP request to a specific API on the device. A successful exploit could allow the attacker to cause a denial of service (DoS) condition due to high CPU utilization, which could negatively impact user traffic and management access. When the attack stops, the device will recover without manual intervention.
A vulnerability in the remote access SSL VPN features of Cisco Adaptive Security Appliance (ASA) Software and Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to improper validation of errors that are logged as a result of client connections that are made using remote access VPN. An attacker could exploit this vulnerability by sending crafted requests to an affected system. A successful exploit could allow the attacker to cause the affected device to restart, resulting in a DoS condition.
A vulnerability in the Cisco Fabric Services over IP (CFSoIP) feature of Cisco NX-OS Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to insufficient validation of incoming CFSoIP packets. An attacker could exploit this vulnerability by sending crafted CFSoIP packets to an affected device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition.
A vulnerability in the UDP processing functionality of Cisco IOS XE Software for Embedded Wireless Controllers on Catalyst 9100 Series Access Points could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition. This vulnerability is due to the improper processing of UDP datagrams. An attacker could exploit this vulnerability by sending malicious UDP datagrams to an affected device. A successful exploit could allow the attacker to cause the device to reload, resulting in a DoS condition.
A vulnerability in the web services interface for remote access VPN features of Cisco Adaptive Security Appliance (ASA) Software and Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition. This vulnerability is due to improper input validation when parsing HTTPS requests. An attacker could exploit this vulnerability by sending a crafted HTTPS request to an affected device. A successful exploit could allow the attacker to cause the device to reload, resulting in a DoS condition.
A vulnerability in the Control and Provisioning of Wireless Access Points (CAPWAP) protocol processing of Cisco IOS XE Wireless Controller Software for the Catalyst 9000 Family could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to inadequate input validation of incoming CAPWAP packets encapsulating multicast DNS (mDNS) queries. An attacker could exploit this vulnerability by connecting to a wireless network and sending a crafted mDNS query, which would flow through and be processed by the wireless controller. A successful exploit could allow the attacker to cause the affected device to crash and reload, resulting in a DoS condition.
A vulnerability in the processing of Control and Provisioning of Wireless Access Points (CAPWAP) Mobility messages in Cisco IOS XE Wireless Controller Software for the Catalyst 9000 Family could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to a logic error and improper management of resources related to the handling of CAPWAP Mobility messages. An attacker could exploit this vulnerability by sending crafted CAPWAP Mobility packets to an affected device. A successful exploit could allow the attacker to exhaust resources on the affected device. This would cause the device to reload, resulting in a DoS condition.
A vulnerability in the Snort rule evaluation function of Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. The vulnerability is due to improper handling of the DNS reputation enforcement rule. An attacker could exploit this vulnerability by sending crafted UDP packets through an affected device to force a buildup of UDP connections. A successful exploit could allow the attacker to cause traffic that is going through the affected device to be dropped, resulting in a DoS condition. Note: This vulnerability only affects Cisco FTD devices that are running Snort 3.
A vulnerability in the remote access VPN feature of Cisco Adaptive Security Appliance (ASA) Software and Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to improper handling of HTTPS requests. An attacker could exploit this vulnerability by sending crafted HTTPS requests to an affected system. A successful exploit could allow the attacker to cause resource exhaustion, resulting in a DoS condition.
A vulnerability in the fragmentation handling code of tunnel protocol packets in Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause an affected system to reload, resulting in a denial of service (DoS) condition. This vulnerability is due to the improper handling of large fragmented tunnel protocol packets. One example of a tunnel protocol is Generic Routing Encapsulation (GRE). An attacker could exploit this vulnerability by sending crafted fragmented packets to an affected system. A successful exploit could allow the attacker to cause the affected system to reload, resulting in a DoS condition. Note: Only traffic directed to the affected system can be used to exploit this vulnerability.
Multiple vulnerabilities in the web-based user interface of certain Cisco Small Business Series Switches could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition or execute arbitrary code with root privileges on an affected device. These vulnerabilities are due to improper validation of requests that are sent to the web interface. For more information about these vulnerabilities, see the Details section of this advisory.
A vulnerability in the RADIUS message processing feature of Cisco Identity Services Engine (ISE) could allow an unauthenticated, remote attacker to cause the affected system to stop processing RADIUS packets. This vulnerability is due to improper handling of certain RADIUS accounting requests. An attacker could exploit this vulnerability by sending a crafted authentication request to a network access device (NAD) that uses Cisco ISE for authentication, authorization, and accounting (AAA). This would eventually result in the NAD sending a RADIUS accounting request packet to Cisco ISE. An attacker could also exploit this vulnerability by sending a crafted RADIUS accounting request packet to Cisco ISE directly if the RADIUS shared secret is known. A successful exploit could allow the attacker to cause the RADIUS process to unexpectedly restart, resulting in authentication or authorization timeouts and denying legitimate users access to the network or service. Clients already authenticated to the network would not be affected. Note: To recover the ability to process RADIUS packets, a manual restart of the affected Policy Service Node (PSN) may be required. For more information, see the Details ["#details"] section of this advisory.
A vulnerability in the multicast DNS (mDNS) feature of Cisco IOS XE Software for Cisco Catalyst 9800 Series Wireless Controllers could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition. The vulnerability is due to improper validation of mDNS packets. An attacker could exploit this vulnerability by sending a crafted mDNS packet to an affected device. A successful exploit could cause a device to reload, resulting in a DoS condition.
A vulnerability in ICMPv6 inspection when configured with the Snort 2 detection engine for Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause the CPU of an affected device to spike to 100 percent, which could stop all traffic processing and result in a denial of service (DoS) condition. FTD management traffic is not affected by this vulnerability. This vulnerability is due to improper error checking when parsing fields within the ICMPv6 header. An attacker could exploit this vulnerability by sending a crafted ICMPv6 packet through an affected device. A successful exploit could allow the attacker to cause the device to exhaust CPU resources and stop processing traffic, resulting in a DoS condition. Note: To recover from the DoS condition, the Snort 2 Detection Engine or the Cisco FTD device may need to be restarted.
A vulnerability in the Split DNS feature of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause an affected device to reload, resulting in a denial of service (DoS) condition. The vulnerability occurs because the regular expression (regex) engine that is used with the Split DNS feature of affected releases may time out when it processes the DNS name list configuration. An attacker could exploit this vulnerability by trying to resolve an address or hostname that the affected device handles. A successful exploit could allow the attacker to cause the device to reload, resulting in a DoS condition.
A vulnerability in the OSPF Version 2 (OSPFv2) implementation of Cisco Adaptive Security Appliance (ASA) Software and Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause an affected device to reload, resulting in a denial of service (DoS) condition. The vulnerability is due to incomplete input validation when the affected software processes certain OSPFv2 packets with Link-Local Signaling (LLS) data. An attacker could exploit this vulnerability by sending a malformed OSPFv2 packet to an affected device. A successful exploit could allow the attacker to cause an affected device to reload, resulting in a DoS condition.
A vulnerability in the process that classifies traffic that is going to the Unified Threat Defense (UTD) component of Cisco IOS XE Software in controller mode could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability exists because UTD improperly handles certain packets as those packets egress an SD-WAN IPsec tunnel. An attacker could exploit this vulnerability by sending crafted traffic through an SD-WAN IPsec tunnel that is configured on an affected device. A successful exploit could allow the attacker to cause the device to reload, resulting in a DoS condition. Note: SD-WAN tunnels that are configured with Generic Routing Encapsulation (GRE) are not affected by this vulnerability.
A vulnerability in the IPv4 Software-Defined Access (SD-Access) fabric edge node feature of Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause high CPU utilization and stop all traffic processing, resulting in a denial of service (DoS) condition on an affected device. This vulnerability is due to improper handling of certain IPv4 packets. An attacker could exploit this vulnerability by sending certain IPv4 packets to an affected device. A successful exploit could allow the attacker to cause the device to exhaust CPU resources and stop processing traffic, resulting in a DoS condition.