In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Remove unused nvme_ls_waitq wait queue System crash when qla2x00_start_sp(sp) returns error code EGAIN and wake_up gets called for uninitialized wait queue sp->nvme_ls_waitq. qla2xxx [0000:37:00.1]-2121:5: Returning existing qpair of ffff8ae2c0513400 for idx=0 qla2xxx [0000:37:00.1]-700e:5: qla2x00_start_sp failed = 11 BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 PGD 0 P4D 0 Oops: 0000 [#1] SMP NOPTI Hardware name: HPE ProLiant DL360 Gen10/ProLiant DL360 Gen10, BIOS U32 09/03/2021 Workqueue: nvme-wq nvme_fc_connect_ctrl_work [nvme_fc] RIP: 0010:__wake_up_common+0x4c/0x190 RSP: 0018:ffff95f3e0cb7cd0 EFLAGS: 00010086 RAX: 0000000000000000 RBX: ffff8b08d3b26328 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 0000000000000003 RDI: ffff8b08d3b26320 RBP: 0000000000000001 R08: 0000000000000000 R09: ffffffffffffffe8 R10: 0000000000000000 R11: ffff95f3e0cb7a60 R12: ffff95f3e0cb7d20 R13: 0000000000000003 R14: 0000000000000000 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff8b2fdf6c0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 0000002f1e410002 CR4: 00000000007706e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: __wake_up_common_lock+0x7c/0xc0 qla_nvme_ls_req+0x355/0x4c0 [qla2xxx] ? __nvme_fc_send_ls_req+0x260/0x380 [nvme_fc] ? nvme_fc_send_ls_req.constprop.42+0x1a/0x45 [nvme_fc] ? nvme_fc_connect_ctrl_work.cold.63+0x1e3/0xa7d [nvme_fc] Remove unused nvme_ls_waitq wait queue. nvme_ls_waitq logic was removed previously in the commits tagged Fixed: below.

In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Avoid fcport pointer dereference Klocwork reported warning of NULL pointer may be dereferenced. The routine exits when sa_ctl is NULL and fcport is allocated after the exit call thus causing NULL fcport pointer to dereference at the time of exit. To avoid fcport pointer dereference, exit the routine when sa_ctl is NULL.

In the Linux kernel, the following vulnerability has been resolved: RDMA/cxgb4: Fix potential null-ptr-deref in pass_establish() If get_ep_from_tid() fails to lookup non-NULL value for ep, ep is dereferenced later regardless of whether it is empty. This patch adds a simple sanity check to fix the issue. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: erofs: fix wrong kunmap when using LZMA on HIGHMEM platforms As the call trace shown, the root cause is kunmap incorrect pages: BUG: kernel NULL pointer dereference, address: 00000000 CPU: 1 PID: 40 Comm: kworker/u5:0 Not tainted 6.2.0-rc5 #4 Workqueue: erofs_worker z_erofs_decompressqueue_work EIP: z_erofs_lzma_decompress+0x34b/0x8ac z_erofs_decompress+0x12/0x14 z_erofs_decompress_queue+0x7e7/0xb1c z_erofs_decompressqueue_work+0x32/0x60 process_one_work+0x24b/0x4d8 ? process_one_work+0x1a4/0x4d8 worker_thread+0x14c/0x3fc kthread+0xe6/0x10c ? rescuer_thread+0x358/0x358 ? kthread_complete_and_exit+0x18/0x18 ret_from_fork+0x1c/0x28 ---[ end trace 0000000000000000 ]--- The bug is trivial and should be fixed now. It has no impact on !HIGHMEM platforms.

In the Linux kernel, the following vulnerability has been resolved: scsi: mpt3sas: Fix NULL pointer access in mpt3sas_transport_port_add() Port is allocated by sas_port_alloc_num() and rphy is allocated by either sas_end_device_alloc() or sas_expander_alloc(), all of which may return NULL. So we need to check the rphy to avoid possible NULL pointer access. If sas_rphy_add() returned with failure, rphy is set to NULL. We would access the rphy in the following lines which would also result NULL pointer access.

In the Linux kernel, the following vulnerability has been resolved: tracing: Fix null pointer dereference in tracing_err_log_open() Fix an issue in function 'tracing_err_log_open'. The function doesn't call 'seq_open' if the file is opened only with write permissions, which results in 'file->private_data' being left as null. If we then use 'lseek' on that opened file, 'seq_lseek' dereferences 'file->private_data' in 'mutex_lock(&m->lock)', resulting in a kernel panic. Writing to this node requires root privileges, therefore this bug has very little security impact. Tracefs node: /sys/kernel/tracing/error_log Example Kernel panic: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000038 Call trace: mutex_lock+0x30/0x110 seq_lseek+0x34/0xb8 __arm64_sys_lseek+0x6c/0xb8 invoke_syscall+0x58/0x13c el0_svc_common+0xc4/0x10c do_el0_svc+0x24/0x98 el0_svc+0x24/0x88 el0t_64_sync_handler+0x84/0xe4 el0t_64_sync+0x1b4/0x1b8 Code: d503201f aa0803e0 aa1f03e1 aa0103e9 (c8e97d02) ---[ end trace 561d1b49c12cf8a5 ]--- Kernel panic - not syncing: Oops: Fatal exception

In the Linux kernel, the following vulnerability has been resolved: net/smc: fix NULL sndbuf_desc in smc_cdc_tx_handler() When performing a stress test on SMC-R by rmmod mlx5_ib driver during the wrk/nginx test, we found that there is a probability of triggering a panic while terminating all link groups. This issue dues to the race between smc_smcr_terminate_all() and smc_buf_create(). smc_smcr_terminate_all smc_buf_create /* init */ conn->sndbuf_desc = NULL; ... __smc_lgr_terminate smc_conn_kill smc_close_abort smc_cdc_get_slot_and_msg_send __softirqentry_text_start smc_wr_tx_process_cqe smc_cdc_tx_handler READ(conn->sndbuf_desc->len); /* panic dues to NULL sndbuf_desc */ conn->sndbuf_desc = xxx; This patch tries to fix the issue by always to check the sndbuf_desc before send any cdc msg, to make sure that no null pointer is seen during cqe processing.

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Check kzalloc() in lpfc_sli4_cgn_params_read() If kzalloc() fails in lpfc_sli4_cgn_params_read(), then we rely on lpfc_read_object()'s routine to NULL check pdata. Currently, an early return error is thrown from lpfc_read_object() to protect us from NULL ptr dereference, but the errno code is -ENODEV. Change the errno code to a more appropriate -ENOMEM.

In the Linux kernel, the following vulnerability has been resolved: ice: Don't tx before switchdev is fully configured There is possibility that ice_eswitch_port_start_xmit might be called while some resources are still not allocated which might cause NULL pointer dereference. Fix this by checking if switchdev configuration was finished.

In the Linux kernel, the following vulnerability has been resolved: drm/msm/dsi: Add missing check for alloc_ordered_workqueue Add check for the return value of alloc_ordered_workqueue as it may return NULL pointer and cause NULL pointer dereference. Patchwork: https://patchwork.freedesktop.org/patch/517646/

In the Linux kernel, the following vulnerability has been resolved: ice: Block switchdev mode when ADQ is active and vice versa ADQ and switchdev are not supported simultaneously. Enabling both at the same time can result in nullptr dereference. To prevent this, check if ADQ is active when changing devlink mode to switchdev mode, and check if switchdev is active when enabling ADQ.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: Avoid NULL pointer access during management transmit cleanup Currently 'ar' reference is not added in skb_cb. Though this is generally not used during transmit completion callbacks, on interface removal the remaining idr cleanup callback uses the ar pointer from skb_cb from management txmgmt_idr. Hence fill them during transmit call for proper usage to avoid NULL pointer dereference. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1

In the Linux kernel, the following vulnerability has been resolved: wifi: nl80211: fix NULL-ptr deref in offchan check If, e.g. in AP mode, the link was already created by userspace but not activated yet, it has a chandef but the chandef isn't valid and has no channel. Check for this and ignore this link.

In the Linux kernel, the following vulnerability has been resolved: can: gs_usb: fix time stamp counter initialization If the gs_usb device driver is unloaded (or unbound) before the interface is shut down, the USB stack first calls the struct usb_driver::disconnect and then the struct net_device_ops::ndo_stop callback. In gs_usb_disconnect() all pending bulk URBs are killed, i.e. no more RX'ed CAN frames are send from the USB device to the host. Later in gs_can_close() a reset control message is send to each CAN channel to remove the controller from the CAN bus. In this race window the USB device can still receive CAN frames from the bus and internally queue them to be send to the host. At least in the current version of the candlelight firmware, the queue of received CAN frames is not emptied during the reset command. After loading (or binding) the gs_usb driver, new URBs are submitted during the struct net_device_ops::ndo_open callback and the candlelight firmware starts sending its already queued CAN frames to the host. However, this scenario was not considered when implementing the hardware timestamp function. The cycle counter/time counter infrastructure is set up (gs_usb_timestamp_init()) after the USBs are submitted, resulting in a NULL pointer dereference if timecounter_cyc2time() (via the call chain: gs_usb_receive_bulk_callback() -> gs_usb_set_timestamp() -> gs_usb_skb_set_timestamp()) is called too early. Move the gs_usb_timestamp_init() function before the URBs are submitted to fix this problem. For a comprehensive solution, we need to consider gs_usb devices with more than 1 channel. The cycle counter/time counter infrastructure is setup per channel, but the RX URBs are per device. Once gs_can_open() of _a_ channel has been called, and URBs have been submitted, the gs_usb_receive_bulk_callback() can be called for _all_ available channels, even for channels that are not running, yet. As cycle counter/time counter has not set up, this will again lead to a NULL pointer dereference. Convert the cycle counter/time counter from a "per channel" to a "per device" functionality. Also set it up, before submitting any URBs to the device. Further in gs_usb_receive_bulk_callback(), don't process any URBs for not started CAN channels, only resubmit the URB.

In the Linux kernel, the following vulnerability has been resolved: xsk: check IFF_UP earlier in Tx path Xsk Tx can be triggered via either sendmsg() or poll() syscalls. These two paths share a call to common function xsk_xmit() which has two sanity checks within. A pseudo code example to show the two paths: __xsk_sendmsg() : xsk_poll(): if (unlikely(!xsk_is_bound(xs))) if (unlikely(!xsk_is_bound(xs))) return -ENXIO; return mask; if (unlikely(need_wait)) (...) return -EOPNOTSUPP; xsk_xmit() mark napi id (...) xsk_xmit() xsk_xmit(): if (unlikely(!(xs->dev->flags & IFF_UP))) return -ENETDOWN; if (unlikely(!xs->tx)) return -ENOBUFS; As it can be observed above, in sendmsg() napi id can be marked on interface that was not brought up and this causes a NULL ptr dereference: [31757.505631] BUG: kernel NULL pointer dereference, address: 0000000000000018 [31757.512710] #PF: supervisor read access in kernel mode [31757.517936] #PF: error_code(0x0000) - not-present page [31757.523149] PGD 0 P4D 0 [31757.525726] Oops: 0000 [#1] PREEMPT SMP NOPTI [31757.530154] CPU: 26 PID: 95641 Comm: xdpsock Not tainted 6.2.0-rc5+ #40 [31757.536871] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0008.031920191559 03/19/2019 [31757.547457] RIP: 0010:xsk_sendmsg+0xde/0x180 [31757.551799] Code: 00 75 a2 48 8b 00 a8 04 75 9b 84 d2 74 69 8b 85 14 01 00 00 85 c0 75 1b 48 8b 85 28 03 00 00 48 8b 80 98 00 00 00 48 8b 40 20 <8b> 40 18 89 85 14 01 00 00 8b bd 14 01 00 00 81 ff 00 01 00 00 0f [31757.570840] RSP: 0018:ffffc90034f27dc0 EFLAGS: 00010246 [31757.576143] RAX: 0000000000000000 RBX: ffffc90034f27e18 RCX: 0000000000000000 [31757.583389] RDX: 0000000000000001 RSI: ffffc90034f27e18 RDI: ffff88984cf3c100 [31757.590631] RBP: ffff88984714a800 R08: ffff88984714a800 R09: 0000000000000000 [31757.597877] R10: 0000000000000001 R11: 0000000000000000 R12: 00000000fffffffa [31757.605123] R13: 0000000000000000 R14: 0000000000000003 R15: 0000000000000000 [31757.612364] FS: 00007fb4c5931180(0000) GS:ffff88afdfa00000(0000) knlGS:0000000000000000 [31757.620571] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [31757.626406] CR2: 0000000000000018 CR3: 000000184b41c003 CR4: 00000000007706e0 [31757.633648] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [31757.640894] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [31757.648139] PKRU: 55555554 [31757.650894] Call Trace: [31757.653385] <TASK> [31757.655524] sock_sendmsg+0x8f/0xa0 [31757.659077] ? sockfd_lookup_light+0x12/0x70 [31757.663416] __sys_sendto+0xfc/0x170 [31757.667051] ? do_sched_setscheduler+0xdb/0x1b0 [31757.671658] __x64_sys_sendto+0x20/0x30 [31757.675557] do_syscall_64+0x38/0x90 [31757.679197] entry_SYSCALL_64_after_hwframe+0x72/0xdc [31757.687969] Code: 8e f6 ff 44 8b 4c 24 2c 4c 8b 44 24 20 41 89 c4 44 8b 54 24 28 48 8b 54 24 18 b8 2c 00 00 00 48 8b 74 24 10 8b 7c 24 08 0f 05 <48> 3d 00 f0 ff ff 77 3a 44 89 e7 48 89 44 24 08 e8 b5 8e f6 ff 48 [31757.707007] RSP: 002b:00007ffd49c73c70 EFLAGS: 00000293 ORIG_RAX: 000000000000002c [31757.714694] RAX: ffffffffffffffda RBX: 000055a996565380 RCX: 00007fb4c5727c16 [31757.721939] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000003 [31757.729184] RBP: 0000000000000040 R08: 0000000000000000 R09: 0000000000000000 [31757.736429] R10: 0000000000000040 R11: 0000000000000293 R12: 0000000000000000 [31757.743673] R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 [31757.754940] </TASK> To fix this, let's make xsk_xmit a function that will be responsible for generic Tx, where RCU is handled accordingly and pull out sanity checks and xs->zc handling. Populate sanity checks to __xsk_sendmsg() and xsk_poll().

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: drop redundant sched job cleanup when cs is aborted Once command submission failed due to userptr invalidation in amdgpu_cs_submit, legacy code will perform cleanup of scheduler job. However, it's not needed at all, as former commit has integrated job cleanup stuff into amdgpu_job_free. Otherwise, because of double free, a NULL pointer dereference will occur in such scenario. Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2457

In the Linux kernel, the following vulnerability has been resolved: i40e: Fix kernel crash during reboot when adapter is in recovery mode If the driver detects during probe that firmware is in recovery mode then i40e_init_recovery_mode() is called and the rest of probe function is skipped including pci_set_drvdata(). Subsequent i40e_shutdown() called during shutdown/reboot dereferences NULL pointer as pci_get_drvdata() returns NULL. To fix call pci_set_drvdata() also during entering to recovery mode. Reproducer: 1) Lets have i40e NIC with firmware in recovery mode 2) Run reboot Result: [ 139.084698] i40e: Intel(R) Ethernet Connection XL710 Network Driver [ 139.090959] i40e: Copyright (c) 2013 - 2019 Intel Corporation. [ 139.108438] i40e 0000:02:00.0: Firmware recovery mode detected. Limiting functionality. [ 139.116439] i40e 0000:02:00.0: Refer to the Intel(R) Ethernet Adapters and Devices User Guide for details on firmware recovery mode. [ 139.129499] i40e 0000:02:00.0: fw 8.3.64775 api 1.13 nvm 8.30 0x8000b78d 1.3106.0 [8086:1583] [15d9:084a] [ 139.215932] i40e 0000:02:00.0 enp2s0f0: renamed from eth0 [ 139.223292] i40e 0000:02:00.1: Firmware recovery mode detected. Limiting functionality. [ 139.231292] i40e 0000:02:00.1: Refer to the Intel(R) Ethernet Adapters and Devices User Guide for details on firmware recovery mode. [ 139.244406] i40e 0000:02:00.1: fw 8.3.64775 api 1.13 nvm 8.30 0x8000b78d 1.3106.0 [8086:1583] [15d9:084a] [ 139.329209] i40e 0000:02:00.1 enp2s0f1: renamed from eth0 ... [ 156.311376] BUG: kernel NULL pointer dereference, address: 00000000000006c2 [ 156.318330] #PF: supervisor write access in kernel mode [ 156.323546] #PF: error_code(0x0002) - not-present page [ 156.328679] PGD 0 P4D 0 [ 156.331210] Oops: 0002 [#1] PREEMPT SMP NOPTI [ 156.335567] CPU: 26 PID: 15119 Comm: reboot Tainted: G E 6.2.0+ #1 [ 156.343126] Hardware name: Abacus electric, s.r.o. - servis@abacus.cz Super Server/H12SSW-iN, BIOS 2.4 04/13/2022 [ 156.353369] RIP: 0010:i40e_shutdown+0x15/0x130 [i40e] [ 156.358430] Code: c1 fc ff ff 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 f3 0f 1e fa 0f 1f 44 00 00 55 48 89 fd 53 48 8b 9f 48 01 00 00 <f0> 80 8b c2 06 00 00 04 f0 80 8b c0 06 00 00 08 48 8d bb 08 08 00 [ 156.377168] RSP: 0018:ffffb223c8447d90 EFLAGS: 00010282 [ 156.382384] RAX: ffffffffc073ee70 RBX: 0000000000000000 RCX: 0000000000000001 [ 156.389510] RDX: 0000000080000001 RSI: 0000000000000246 RDI: ffff95db49988000 [ 156.396634] RBP: ffff95db49988000 R08: ffffffffffffffff R09: ffffffff8bd17d40 [ 156.403759] R10: 0000000000000001 R11: ffffffff8a5e3d28 R12: ffff95db49988000 [ 156.410882] R13: ffffffff89a6fe17 R14: ffff95db49988150 R15: 0000000000000000 [ 156.418007] FS: 00007fe7c0cc3980(0000) GS:ffff95ea8ee80000(0000) knlGS:0000000000000000 [ 156.426083] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 156.431819] CR2: 00000000000006c2 CR3: 00000003092fc005 CR4: 0000000000770ee0 [ 156.438944] PKRU: 55555554 [ 156.441647] Call Trace: [ 156.444096] <TASK> [ 156.446199] pci_device_shutdown+0x38/0x60 [ 156.450297] device_shutdown+0x163/0x210 [ 156.454215] kernel_restart+0x12/0x70 [ 156.457872] __do_sys_reboot+0x1ab/0x230 [ 156.461789] ? vfs_writev+0xa6/0x1a0 [ 156.465362] ? __pfx_file_free_rcu+0x10/0x10 [ 156.469635] ? __call_rcu_common.constprop.85+0x109/0x5a0 [ 156.475034] do_syscall_64+0x3e/0x90 [ 156.478611] entry_SYSCALL_64_after_hwframe+0x72/0xdc [ 156.483658] RIP: 0033:0x7fe7bff37ab7

In the Linux kernel, the following vulnerability has been resolved: ALSA: ac97: Fix possible NULL dereference in snd_ac97_mixer smatch error: sound/pci/ac97/ac97_codec.c:2354 snd_ac97_mixer() error: we previously assumed 'rac97' could be null (see line 2072) remove redundant assignment, return error if rac97 is NULL.

In the Linux kernel, the following vulnerability has been resolved: HID: betop: check shape of output reports betopff_init() only checks the total sum of the report counts for each report field to be at least 4, but hid_betopff_play() expects 4 report fields. A device advertising an output report with one field and 4 report counts would pass the check but crash the kernel with a NULL pointer dereference in hid_betopff_play().

In the Linux kernel, the following vulnerability has been resolved: qed/qed_sriov: guard against NULL derefs from qed_iov_get_vf_info We have to make sure that the info returned by the helper is valid before using it. Found by Linux Verification Center (linuxtesting.org) with the SVACE static analysis tool.

In the Linux kernel, the following vulnerability has been resolved: sctp: check send stream number after wait_for_sndbuf This patch fixes a corner case where the asoc out stream count may change after wait_for_sndbuf. When the main thread in the client starts a connection, if its out stream count is set to N while the in stream count in the server is set to N - 2, another thread in the client keeps sending the msgs with stream number N - 1, and waits for sndbuf before processing INIT_ACK. However, after processing INIT_ACK, the out stream count in the client is shrunk to N - 2, the same to the in stream count in the server. The crash occurs when the thread waiting for sndbuf is awake and sends the msg in a non-existing stream(N - 1), the call trace is as below: KASAN: null-ptr-deref in range [0x0000000000000038-0x000000000000003f] Call Trace: <TASK> sctp_cmd_send_msg net/sctp/sm_sideeffect.c:1114 [inline] sctp_cmd_interpreter net/sctp/sm_sideeffect.c:1777 [inline] sctp_side_effects net/sctp/sm_sideeffect.c:1199 [inline] sctp_do_sm+0x197d/0x5310 net/sctp/sm_sideeffect.c:1170 sctp_primitive_SEND+0x9f/0xc0 net/sctp/primitive.c:163 sctp_sendmsg_to_asoc+0x10eb/0x1a30 net/sctp/socket.c:1868 sctp_sendmsg+0x8d4/0x1d90 net/sctp/socket.c:2026 inet_sendmsg+0x9d/0xe0 net/ipv4/af_inet.c:825 sock_sendmsg_nosec net/socket.c:722 [inline] sock_sendmsg+0xde/0x190 net/socket.c:745 The fix is to add an unlikely check for the send stream number after the thread wakes up from the wait_for_sndbuf.

In the Linux kernel, the following vulnerability has been resolved: acpi: Fix suspend with Xen PV Commit f1e525009493 ("x86/boot: Skip realmode init code when running as Xen PV guest") missed one code path accessing real_mode_header, leading to dereferencing NULL when suspending the system under Xen: [ 348.284004] PM: suspend entry (deep) [ 348.289532] Filesystems sync: 0.005 seconds [ 348.291545] Freezing user space processes ... (elapsed 0.000 seconds) done. [ 348.292457] OOM killer disabled. [ 348.292462] Freezing remaining freezable tasks ... (elapsed 0.104 seconds) done. [ 348.396612] printk: Suspending console(s) (use no_console_suspend to debug) [ 348.749228] PM: suspend devices took 0.352 seconds [ 348.769713] ACPI: EC: interrupt blocked [ 348.816077] BUG: kernel NULL pointer dereference, address: 000000000000001c [ 348.816080] #PF: supervisor read access in kernel mode [ 348.816081] #PF: error_code(0x0000) - not-present page [ 348.816083] PGD 0 P4D 0 [ 348.816086] Oops: 0000 [#1] PREEMPT SMP NOPTI [ 348.816089] CPU: 0 PID: 6764 Comm: systemd-sleep Not tainted 6.1.3-1.fc32.qubes.x86_64 #1 [ 348.816092] Hardware name: Star Labs StarBook/StarBook, BIOS 8.01 07/03/2022 [ 348.816093] RIP: e030:acpi_get_wakeup_address+0xc/0x20 Fix that by adding an optional acpi callback allowing to skip setting the wakeup address, as in the Xen PV case this will be handled by the hypervisor anyway.

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: do not run mt76_unregister_device() on unregistered hw Trying to probe a mt7921e pci card without firmware results in a successful probe where ieee80211_register_hw hasn't been called. When removing the driver, ieee802111_unregister_hw is called unconditionally leading to a kernel NULL pointer dereference. Fix the issue running mt76_unregister_device routine just for registered hw.

In the Linux kernel, the following vulnerability has been resolved: net/smc: Reset connection when trying to use SMCRv2 fails. We found a crash when using SMCRv2 with 2 Mellanox ConnectX-4. It can be reproduced by: - smc_run nginx - smc_run wrk -t 32 -c 500 -d 30 http://<ip>:<port> BUG: kernel NULL pointer dereference, address: 0000000000000014 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 8000000108713067 P4D 8000000108713067 PUD 151127067 PMD 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 4 PID: 2441 Comm: kworker/4:249 Kdump: loaded Tainted: G W E 6.4.0-rc1+ #42 Workqueue: smc_hs_wq smc_listen_work [smc] RIP: 0010:smc_clc_send_confirm_accept+0x284/0x580 [smc] RSP: 0018:ffffb8294b2d7c78 EFLAGS: 00010a06 RAX: ffff8f1873238880 RBX: ffffb8294b2d7dc8 RCX: 0000000000000000 RDX: 00000000000000b4 RSI: 0000000000000001 RDI: 0000000000b40c00 RBP: ffffb8294b2d7db8 R08: ffff8f1815c5860c R09: 0000000000000000 R10: 0000000000000400 R11: 0000000000000000 R12: ffff8f1846f56180 R13: ffff8f1815c5860c R14: 0000000000000001 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff8f1aefd00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000014 CR3: 00000001027a0001 CR4: 00000000003706e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? mlx5_ib_map_mr_sg+0xa1/0xd0 [mlx5_ib] ? smcr_buf_map_link+0x24b/0x290 [smc] ? __smc_buf_create+0x4ee/0x9b0 [smc] smc_clc_send_accept+0x4c/0xb0 [smc] smc_listen_work+0x346/0x650 [smc] ? __schedule+0x279/0x820 process_one_work+0x1e5/0x3f0 worker_thread+0x4d/0x2f0 ? __pfx_worker_thread+0x10/0x10 kthread+0xe5/0x120 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2c/0x50 </TASK> During the CLC handshake, server sequentially tries available SMCRv2 and SMCRv1 devices in smc_listen_work(). If an SMCRv2 device is found. SMCv2 based link group and link will be assigned to the connection. Then assumed that some buffer assignment errors happen later in the CLC handshake, such as RMB registration failure, server will give up SMCRv2 and try SMCRv1 device instead. But the resources assigned to the connection won't be reset. When server tries SMCRv1 device, the connection creation process will be executed again. Since conn->lnk has been assigned when trying SMCRv2, it will not be set to the correct SMCRv1 link in smcr_lgr_conn_assign_link(). So in such situation, conn->lgr points to correct SMCRv1 link group but conn->lnk points to the SMCRv2 link mistakenly. Then in smc_clc_send_confirm_accept(), conn->rmb_desc->mr[link->link_idx] will be accessed. Since the link->link_idx is not correct, the related MR may not have been initialized, so crash happens. | Try SMCRv2 device first | |-> conn->lgr: assign existed SMCRv2 link group; | |-> conn->link: assign existed SMCRv2 link (link_idx may be 1 in SMC_LGR_SYMMETRIC); | |-> sndbuf & RMB creation fails, quit; | | Try SMCRv1 device then | |-> conn->lgr: create SMCRv1 link group and assign; | |-> conn->link: keep SMCRv2 link mistakenly; | |-> sndbuf & RMB creation succeed, only RMB->mr[link_idx = 0] | initialized. | | Then smc_clc_send_confirm_accept() accesses | conn->rmb_desc->mr[conn->link->link_idx, which is 1], then crash. v This patch tries to fix this by cleaning conn->lnk before assigning link. In addition, it is better to reset the connection and clean the resources assigned if trying SMCRv2 failed in buffer creation or registration.

A NULL pointer dereference vulnerability was found in vmwgfx driver in drivers/gpu/vmxgfx/vmxgfx_execbuf.c in GPU component of Linux kernel with device file '/dev/dri/renderD128 (or Dxxx)'. This flaw allows a local attacker with a user account on the system to gain privilege, causing a denial of service(DoS).

In the Linux kernel, the following vulnerability has been resolved: usb: ucsi_acpi: Increase the command completion timeout Commit 130a96d698d7 ("usb: typec: ucsi: acpi: Increase command completion timeout value") increased the timeout from 5 seconds to 60 seconds due to issues related to alternate mode discovery. After the alternate mode discovery switch to polled mode the timeout was reduced, but instead of being set back to 5 seconds it was reduced to 1 second. This is causing problems when using a Lenovo ThinkPad X1 yoga gen7 connected over Type-C to a LG 27UL850-W (charging DP over Type-C). When the monitor is already connected at boot the following error is logged: "PPM init failed (-110)", /sys/class/typec is empty and on unplugging the NULL pointer deref fixed earlier in this series happens. When the monitor is connected after boot the following error is logged instead: "GET_CONNECTOR_STATUS failed (-110)". Setting the timeout back to 5 seconds fixes both cases.

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: u_serial: Add null pointer check in gserial_resume Consider a case where gserial_disconnect has already cleared gser->ioport. And if a wakeup interrupt triggers afterwards, gserial_resume gets called, which will lead to accessing of gser->ioport and thus causing null pointer dereference.Add a null pointer check to prevent this. Added a static spinlock to prevent gser->ioport from becoming null after the newly added check.

In the Linux kernel, the following vulnerability has been resolved: crypto: af_alg - Fix missing initialisation affecting gcm-aes-s390 Fix af_alg_alloc_areq() to initialise areq->first_rsgl.sgl.sgt.sgl to point to the scatterlist array in areq->first_rsgl.sgl.sgl. Without this, the gcm-aes-s390 driver will oops when it tries to do gcm_walk_start() on req->dst because req->dst is set to the value of areq->first_rsgl.sgl.sgl by _aead_recvmsg() calling aead_request_set_crypt(). The problem comes if an empty ciphertext is passed: the loop in af_alg_get_rsgl() just passes straight out and doesn't set areq->first_rsgl up. This isn't a problem on x86_64 using gcmaes_crypt_by_sg() because, as far as I can tell, that ignores req->dst and only uses req->src[*]. [*] Is this a bug in aesni-intel_glue.c? The s390x oops looks something like: Unable to handle kernel pointer dereference in virtual kernel address space Failing address: 0000000a00000000 TEID: 0000000a00000803 Fault in home space mode while using kernel ASCE. AS:00000000a43a0007 R3:0000000000000024 Oops: 003b ilc:2 [#1] SMP ... Call Trace: [<000003ff7fc3d47e>] gcm_walk_start+0x16/0x28 [aes_s390] [<00000000a2a342f2>] crypto_aead_decrypt+0x9a/0xb8 [<00000000a2a60888>] aead_recvmsg+0x478/0x698 [<00000000a2e519a0>] sock_recvmsg+0x70/0xb0 [<00000000a2e51a56>] sock_read_iter+0x76/0xa0 [<00000000a273e066>] vfs_read+0x26e/0x2a8 [<00000000a273e8c4>] ksys_read+0xbc/0x100 [<00000000a311d808>] __do_syscall+0x1d0/0x1f8 [<00000000a312ff30>] system_call+0x70/0x98 Last Breaking-Event-Address: [<000003ff7fc3e6b4>] gcm_aes_crypt+0x104/0xa68 [aes_s390]

In the Linux kernel, the following vulnerability has been resolved: net: stmmac: enable all safety features by default In the original implementation of dwmac5 commit 8bf993a5877e ("net: stmmac: Add support for DWMAC5 and implement Safety Features") all safety features were enabled by default. Later it seems some implementations didn't have support for all the features, so in commit 5ac712dcdfef ("net: stmmac: enable platform specific safety features") the safety_feat_cfg structure was added to the callback and defined for some platforms to selectively enable these safety features. The problem is that only certain platforms were given that software support. If the automotive safety package bit is set in the hardware features register the safety feature callback is called for the platform, and for platforms that didn't get a safety_feat_cfg defined this results in the following NULL pointer dereference: [ 7.933303] Call trace: [ 7.935812] dwmac5_safety_feat_config+0x20/0x170 [stmmac] [ 7.941455] __stmmac_open+0x16c/0x474 [stmmac] [ 7.946117] stmmac_open+0x38/0x70 [stmmac] [ 7.950414] __dev_open+0x100/0x1dc [ 7.954006] __dev_change_flags+0x18c/0x204 [ 7.958297] dev_change_flags+0x24/0x6c [ 7.962237] do_setlink+0x2b8/0xfa4 [ 7.965827] __rtnl_newlink+0x4ec/0x840 [ 7.969766] rtnl_newlink+0x50/0x80 [ 7.973353] rtnetlink_rcv_msg+0x12c/0x374 [ 7.977557] netlink_rcv_skb+0x5c/0x130 [ 7.981500] rtnetlink_rcv+0x18/0x2c [ 7.985172] netlink_unicast+0x2e8/0x340 [ 7.989197] netlink_sendmsg+0x1a8/0x420 [ 7.993222] ____sys_sendmsg+0x218/0x280 [ 7.997249] ___sys_sendmsg+0xac/0x100 [ 8.001103] __sys_sendmsg+0x84/0xe0 [ 8.004776] __arm64_sys_sendmsg+0x24/0x30 [ 8.008983] invoke_syscall+0x48/0x114 [ 8.012840] el0_svc_common.constprop.0+0xcc/0xec [ 8.017665] do_el0_svc+0x38/0xb0 [ 8.021071] el0_svc+0x2c/0x84 [ 8.024212] el0t_64_sync_handler+0xf4/0x120 [ 8.028598] el0t_64_sync+0x190/0x194 Go back to the original behavior, if the automotive safety package is found to be supported in hardware enable all the features unless safety_feat_cfg is passed in saying this particular platform only supports a subset of the features.

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: Enhance sanity check while generating attr_list ni_create_attr_list uses WARN_ON to catch error cases while generating attribute list, which only prints out stack trace and may not be enough. This repalces them with more proper error handling flow. [ 59.666332] BUG: kernel NULL pointer dereference, address: 000000000000000e [ 59.673268] #PF: supervisor read access in kernel mode [ 59.678354] #PF: error_code(0x0000) - not-present page [ 59.682831] PGD 8000000005ff1067 P4D 8000000005ff1067 PUD 7dee067 PMD 0 [ 59.688556] Oops: 0000 [#1] PREEMPT SMP KASAN PTI [ 59.692642] CPU: 0 PID: 198 Comm: poc Tainted: G B W 6.2.0-rc1+ #4 [ 59.698868] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 [ 59.708795] RIP: 0010:ni_create_attr_list+0x505/0x860 [ 59.713657] Code: 7e 10 e8 5e d0 d0 ff 45 0f b7 76 10 48 8d 7b 16 e8 00 d1 d0 ff 66 44 89 73 16 4d 8d 75 0e 4c 89 f7 e8 3f d0 d0 ff 4c 8d8 [ 59.731559] RSP: 0018:ffff88800a56f1e0 EFLAGS: 00010282 [ 59.735691] RAX: 0000000000000001 RBX: ffff88800b7b5088 RCX: ffffffffb83079fe [ 59.741792] RDX: 0000000000000001 RSI: 0000000000000008 RDI: ffffffffbb7f9fc0 [ 59.748423] RBP: ffff88800a56f3a8 R08: ffff88800b7b50a0 R09: fffffbfff76ff3f9 [ 59.754654] R10: ffffffffbb7f9fc7 R11: fffffbfff76ff3f8 R12: ffff88800b756180 [ 59.761552] R13: 0000000000000000 R14: 000000000000000e R15: 0000000000000050 [ 59.768323] FS: 00007feaa8c96440(0000) GS:ffff88806d400000(0000) knlGS:0000000000000000 [ 59.776027] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 59.781395] CR2: 00007f3a2e0b1000 CR3: 000000000a5bc000 CR4: 00000000000006f0 [ 59.787607] Call Trace: [ 59.790271] <TASK> [ 59.792488] ? __pfx_ni_create_attr_list+0x10/0x10 [ 59.797235] ? kernel_text_address+0xd3/0xe0 [ 59.800856] ? unwind_get_return_address+0x3e/0x60 [ 59.805101] ? __kasan_check_write+0x18/0x20 [ 59.809296] ? preempt_count_sub+0x1c/0xd0 [ 59.813421] ni_ins_attr_ext+0x52c/0x5c0 [ 59.817034] ? __pfx_ni_ins_attr_ext+0x10/0x10 [ 59.821926] ? __vfs_setxattr+0x121/0x170 [ 59.825718] ? __vfs_setxattr_noperm+0x97/0x300 [ 59.829562] ? __vfs_setxattr_locked+0x145/0x170 [ 59.833987] ? vfs_setxattr+0x137/0x2a0 [ 59.836732] ? do_setxattr+0xce/0x150 [ 59.839807] ? setxattr+0x126/0x140 [ 59.842353] ? path_setxattr+0x164/0x180 [ 59.845275] ? __x64_sys_setxattr+0x71/0x90 [ 59.848838] ? do_syscall_64+0x3f/0x90 [ 59.851898] ? entry_SYSCALL_64_after_hwframe+0x72/0xdc [ 59.857046] ? stack_depot_save+0x17/0x20 [ 59.860299] ni_insert_attr+0x1ba/0x420 [ 59.863104] ? __pfx_ni_insert_attr+0x10/0x10 [ 59.867069] ? preempt_count_sub+0x1c/0xd0 [ 59.869897] ? _raw_spin_unlock_irqrestore+0x2b/0x50 [ 59.874088] ? __create_object+0x3ae/0x5d0 [ 59.877865] ni_insert_resident+0xc4/0x1c0 [ 59.881430] ? __pfx_ni_insert_resident+0x10/0x10 [ 59.886355] ? kasan_save_alloc_info+0x1f/0x30 [ 59.891117] ? __kasan_kmalloc+0x8b/0xa0 [ 59.894383] ntfs_set_ea+0x90d/0xbf0 [ 59.897703] ? __pfx_ntfs_set_ea+0x10/0x10 [ 59.901011] ? kernel_text_address+0xd3/0xe0 [ 59.905308] ? __kernel_text_address+0x16/0x50 [ 59.909811] ? unwind_get_return_address+0x3e/0x60 [ 59.914898] ? __pfx_stack_trace_consume_entry+0x10/0x10 [ 59.920250] ? arch_stack_walk+0xa2/0x100 [ 59.924560] ? filter_irq_stacks+0x27/0x80 [ 59.928722] ntfs_setxattr+0x405/0x440 [ 59.932512] ? __pfx_ntfs_setxattr+0x10/0x10 [ 59.936634] ? kvmalloc_node+0x2d/0x120 [ 59.940378] ? kasan_save_stack+0x41/0x60 [ 59.943870] ? kasan_save_stack+0x2a/0x60 [ 59.947719] ? kasan_set_track+0x29/0x40 [ 59.951417] ? kasan_save_alloc_info+0x1f/0x30 [ 59.955733] ? __kasan_kmalloc+0x8b/0xa0 [ 59.959598] ? __kmalloc_node+0x68/0x150 [ 59.963163] ? kvmalloc_node+0x2d/0x120 [ 59.966490] ? vmemdup_user+0x2b/0xa0 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: rcu: Protect rcu_print_task_exp_stall() ->exp_tasks access For kernels built with CONFIG_PREEMPT_RCU=y, the following scenario can result in a NULL-pointer dereference: CPU1 CPU2 rcu_preempt_deferred_qs_irqrestore rcu_print_task_exp_stall if (special.b.blocked) READ_ONCE(rnp->exp_tasks) != NULL raw_spin_lock_rcu_node np = rcu_next_node_entry(t, rnp) if (&t->rcu_node_entry == rnp->exp_tasks) WRITE_ONCE(rnp->exp_tasks, np) .... raw_spin_unlock_irqrestore_rcu_node raw_spin_lock_irqsave_rcu_node t = list_entry(rnp->exp_tasks->prev, struct task_struct, rcu_node_entry) (if rnp->exp_tasks is NULL, this will dereference a NULL pointer) The problem is that CPU2 accesses the rcu_node structure's->exp_tasks field without holding the rcu_node structure's ->lock and CPU2 did not observe CPU1's change to rcu_node structure's ->exp_tasks in time. Therefore, if CPU1 sets rcu_node structure's->exp_tasks pointer to NULL, then CPU2 might dereference that NULL pointer. This commit therefore holds the rcu_node structure's ->lock while accessing that structure's->exp_tasks field. [ paulmck: Apply Frederic Weisbecker feedback. ]

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Fix potential null pointer derefernce The amdgpu_ras_get_context may return NULL if device not support ras feature, so add check before using.

In the Linux kernel, the following vulnerability has been resolved: s390/dasd: protect device queue against concurrent access In dasd_profile_start() the amount of requests on the device queue are counted. The access to the device queue is unprotected against concurrent access. With a lot of parallel I/O, especially with alias devices enabled, the device queue can change while dasd_profile_start() is accessing the queue. In the worst case this leads to a kernel panic due to incorrect pointer accesses. Fix this by taking the device lock before accessing the queue and counting the requests. Additionally the check for a valid profile data pointer can be done earlier to avoid unnecessary locking in a hot path.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Fix potential NULL dereference Fix potential NULL dereference, in the case when "man", the resource manager might be NULL, when/if we print debug information.

In the Linux kernel, the following vulnerability has been resolved: ALSA: hda: Fix possible null-ptr-deref when assigning a stream While AudioDSP drivers assign streams exclusively of HOST or LINK type, nothing blocks a user to attempt to assign a COUPLED stream. As supplied substream instance may be a stub, what is the case when code-loading, such scenario ends with null-ptr-deref.

In the Linux kernel, the following vulnerability has been resolved: LoongArch: Set all reserved memblocks on Node#0 at initialization After commit 61167ad5fecdea ("mm: pass nid to reserve_bootmem_region()") we get a panic if DEFERRED_STRUCT_PAGE_INIT is enabled: [ 0.000000] CPU 0 Unable to handle kernel paging request at virtual address 0000000000002b82, era == 90000000040e3f28, ra == 90000000040e3f18 [ 0.000000] Oops[#1]: [ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 6.5.0+ #733 [ 0.000000] pc 90000000040e3f28 ra 90000000040e3f18 tp 90000000046f4000 sp 90000000046f7c90 [ 0.000000] a0 0000000000000001 a1 0000000000200000 a2 0000000000000040 a3 90000000046f7ca0 [ 0.000000] a4 90000000046f7ca4 a5 0000000000000000 a6 90000000046f7c38 a7 0000000000000000 [ 0.000000] t0 0000000000000002 t1 9000000004b00ac8 t2 90000000040e3f18 t3 90000000040f0800 [ 0.000000] t4 00000000000f0000 t5 80000000ffffe07e t6 0000000000000003 t7 900000047fff5e20 [ 0.000000] t8 aaaaaaaaaaaaaaab u0 0000000000000018 s9 0000000000000000 s0 fffffefffe000000 [ 0.000000] s1 0000000000000000 s2 0000000000000080 s3 0000000000000040 s4 0000000000000000 [ 0.000000] s5 0000000000000000 s6 fffffefffe000000 s7 900000000470b740 s8 9000000004ad4000 [ 0.000000] ra: 90000000040e3f18 reserve_bootmem_region+0xec/0x21c [ 0.000000] ERA: 90000000040e3f28 reserve_bootmem_region+0xfc/0x21c [ 0.000000] CRMD: 000000b0 (PLV0 -IE -DA +PG DACF=CC DACM=CC -WE) [ 0.000000] PRMD: 00000000 (PPLV0 -PIE -PWE) [ 0.000000] EUEN: 00000000 (-FPE -SXE -ASXE -BTE) [ 0.000000] ECFG: 00070800 (LIE=11 VS=7) [ 0.000000] ESTAT: 00010800 [PIL] (IS=11 ECode=1 EsubCode=0) [ 0.000000] BADV: 0000000000002b82 [ 0.000000] PRID: 0014d000 (Loongson-64bit, Loongson-3A6000) [ 0.000000] Modules linked in: [ 0.000000] Process swapper (pid: 0, threadinfo=(____ptrval____), task=(____ptrval____)) [ 0.000000] Stack : 0000000000000000 9000000002eb5430 0000003a00000020 90000000045ccd00 [ 0.000000] 900000000470e000 90000000002c1918 0000000000000000 9000000004110780 [ 0.000000] 00000000fe6c0000 0000000480000000 9000000004b4e368 9000000004110748 [ 0.000000] 0000000000000000 900000000421ca84 9000000004620000 9000000004564970 [ 0.000000] 90000000046f7d78 9000000002cc9f70 90000000002c1918 900000000470e000 [ 0.000000] 9000000004564970 90000000040bc0e0 90000000046f7d78 0000000000000000 [ 0.000000] 0000000000004000 90000000045ccd00 0000000000000000 90000000002c1918 [ 0.000000] 90000000002c1900 900000000470b700 9000000004b4df78 9000000004620000 [ 0.000000] 90000000046200a8 90000000046200a8 0000000000000000 9000000004218b2c [ 0.000000] 9000000004270008 0000000000000001 0000000000000000 90000000045ccd00 [ 0.000000] ... [ 0.000000] Call Trace: [ 0.000000] [<90000000040e3f28>] reserve_bootmem_region+0xfc/0x21c [ 0.000000] [<900000000421ca84>] memblock_free_all+0x114/0x350 [ 0.000000] [<9000000004218b2c>] mm_core_init+0x138/0x3cc [ 0.000000] [<9000000004200e38>] start_kernel+0x488/0x7a4 [ 0.000000] [<90000000040df0d8>] kernel_entry+0xd8/0xdc [ 0.000000] [ 0.000000] Code: 02eb21ad 00410f4c 380c31ac <262b818d> 6800b70d 02c1c196 0015001c 57fe4bb1 260002cd The reason is early memblock_reserve() in memblock_init() set node id to MAX_NUMNODES, making NODE_DATA(nid) a NULL dereference in the call chain reserve_bootmem_region() -> init_reserved_page(). After memblock_init(), those late calls of memblock_reserve() operate on subregions of memblock .memory regions. As a result, these reserved regions will be set to the correct node at the first iteration of memmap_init_reserved_pages(). So set all reserved memblocks on Node#0 at initialization can avoid this panic.

In the Linux kernel, the following vulnerability has been resolved: drm/bridge: lt8912b: Fix crash on bridge detach The lt8912b driver, in its bridge detach function, calls drm_connector_unregister() and drm_connector_cleanup(). drm_connector_unregister() should be called only for connectors explicitly registered with drm_connector_register(), which is not the case in lt8912b. The driver's drm_connector_funcs.destroy hook is set to drm_connector_cleanup(). Thus the driver should not call either drm_connector_unregister() nor drm_connector_cleanup() in its lt8912_bridge_detach(), as they cause a crash on bridge detach: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 Mem abort info: ESR = 0x0000000096000006 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x06: level 2 translation fault Data abort info: ISV = 0, ISS = 0x00000006, ISS2 = 0x00000000 CM = 0, WnR = 0, TnD = 0, TagAccess = 0 GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 user pgtable: 4k pages, 48-bit VAs, pgdp=00000000858f3000 [0000000000000000] pgd=0800000085918003, p4d=0800000085918003, pud=0800000085431003, pmd=0000000000000000 Internal error: Oops: 0000000096000006 [#1] PREEMPT SMP Modules linked in: tidss(-) display_connector lontium_lt8912b tc358768 panel_lvds panel_simple drm_dma_helper drm_kms_helper drm drm_panel_orientation_quirks CPU: 3 PID: 462 Comm: rmmod Tainted: G W 6.5.0-rc2+ #2 Hardware name: Toradex Verdin AM62 on Verdin Development Board (DT) pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : drm_connector_cleanup+0x78/0x2d4 [drm] lr : lt8912_bridge_detach+0x54/0x6c [lontium_lt8912b] sp : ffff800082ed3a90 x29: ffff800082ed3a90 x28: ffff0000040c1940 x27: 0000000000000000 x26: 0000000000000000 x25: dead000000000122 x24: dead000000000122 x23: dead000000000100 x22: ffff000003fb6388 x21: 0000000000000000 x20: 0000000000000000 x19: ffff000003fb6260 x18: fffffffffffe56e8 x17: 0000000000000000 x16: 0010000000000000 x15: 0000000000000038 x14: 0000000000000000 x13: ffff800081914b48 x12: 000000000000040e x11: 000000000000015a x10: ffff80008196ebb8 x9 : ffff800081914b48 x8 : 00000000ffffefff x7 : ffff0000040c1940 x6 : ffff80007aa649d0 x5 : 0000000000000000 x4 : 0000000000000001 x3 : ffff80008159e008 x2 : 0000000000000000 x1 : 0000000000000000 x0 : 0000000000000000 Call trace: drm_connector_cleanup+0x78/0x2d4 [drm] lt8912_bridge_detach+0x54/0x6c [lontium_lt8912b] drm_bridge_detach+0x44/0x84 [drm] drm_encoder_cleanup+0x40/0xb8 [drm] drmm_encoder_alloc_release+0x1c/0x30 [drm] drm_managed_release+0xac/0x148 [drm] drm_dev_put.part.0+0x88/0xb8 [drm] devm_drm_dev_init_release+0x14/0x24 [drm] devm_action_release+0x14/0x20 release_nodes+0x5c/0x90 devres_release_all+0x8c/0xe0 device_unbind_cleanup+0x18/0x68 device_release_driver_internal+0x208/0x23c driver_detach+0x4c/0x94 bus_remove_driver+0x70/0xf4 driver_unregister+0x30/0x60 platform_driver_unregister+0x14/0x20 tidss_platform_driver_exit+0x18/0xb2c [tidss] __arm64_sys_delete_module+0x1a0/0x2b4 invoke_syscall+0x48/0x110 el0_svc_common.constprop.0+0x60/0x10c do_el0_svc_compat+0x1c/0x40 el0_svc_compat+0x40/0xac el0t_32_sync_handler+0xb0/0x138 el0t_32_sync+0x194/0x198 Code: 9104a276 f2fbd5b7 aa0203e1 91008af8 (f85c0420)

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/vkms: fix a possible null pointer dereference In amdgpu_vkms_conn_get_modes(), the return value of drm_cvt_mode() is assigned to mode, which will lead to a NULL pointer dereference on failure of drm_cvt_mode(). Add a check to avoid null pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: tls: fix NULL deref on tls_sw_splice_eof() with empty record syzkaller discovered that if tls_sw_splice_eof() is executed as part of sendfile() when the plaintext/ciphertext sk_msg are empty, the send path gets confused because the empty ciphertext buffer does not have enough space for the encryption overhead. This causes tls_push_record() to go on the `split = true` path (which is only supposed to be used when interacting with an attached BPF program), and then get further confused and hit the tls_merge_open_record() path, which then assumes that there must be at least one populated buffer element, leading to a NULL deref. It is possible to have empty plaintext/ciphertext buffers if we previously bailed from tls_sw_sendmsg_locked() via the tls_trim_both_msgs() path. tls_sw_push_pending_record() already handles this case correctly; let's do the same check in tls_sw_splice_eof().

In the Linux kernel, the following vulnerability has been resolved: media: pci: cx23885: check cx23885_vdev_init() return cx23885_vdev_init() can return a NULL pointer, but that pointer is used in the next line without a check. Add a NULL pointer check and go to the error unwind if it is NULL.

In the Linux kernel, the following vulnerability has been resolved: RDMA/irdma: Fix potential NULL-ptr-dereference in_dev_get() can return NULL which will cause a failure once idev is dereferenced in in_dev_for_each_ifa_rtnl(). This patch adds a check for NULL value in idev beforehand. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: clk: mediatek: clk-mt6779: Add check for mtk_alloc_clk_data Add the check for the return value of mtk_alloc_clk_data() in order to avoid NULL pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: ALSA: hda: Do not unset preset when cleaning up codec Several functions that take part in codec's initialization and removal are re-used by ASoC codec drivers implementations. Drivers mimic the behavior of hda_codec_driver_probe/remove() found in sound/pci/hda/hda_bind.c with their component->probe/remove() instead. One of the reasons for that is the expectation of snd_hda_codec_device_new() to receive a valid pointer to an instance of struct snd_card. This expectation can be met only once sound card components probing commences. As ASoC sound card may be unbound without codec device being actually removed from the system, unsetting ->preset in snd_hda_codec_cleanup_for_unbind() interferes with module unload -> load scenario causing null-ptr-deref. Preset is assigned only once, during device/driver matching whereas ASoC codec driver's module reloading may occur several times throughout the lifetime of an audio stack.

In the Linux kernel, the following vulnerability has been resolved: media: hantro: Check whether reset op is defined before use The i.MX8MM/N/P does not define the .reset op since reset of the VPU is done by genpd. Check whether the .reset op is defined before calling it to avoid NULL pointer dereference. Note that the Fixes tag is set to the commit which removed the reset op from i.MX8M Hantro G2 implementation, this is because before this commit all the implementations did define the .reset op.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Check writeback connectors in create_validate_stream_for_sink [WHY & HOW] This is to check connector type to avoid unhandled null pointer for writeback connectors.

In the Linux kernel, the following vulnerability has been resolved: gfs2: Fix kernel NULL pointer dereference in gfs2_rgrp_dump Syzkaller has reported a NULL pointer dereference when accessing rgd->rd_rgl in gfs2_rgrp_dump(). This can happen when creating rgd->rd_gl fails in read_rindex_entry(). Add a NULL pointer check in gfs2_rgrp_dump() to prevent that.

In the Linux kernel, the following vulnerability has been resolved: net: rds: Fix possible NULL-pointer dereference In rds_rdma_cm_event_handler_cmn() check, if conn pointer exists before dereferencing it as rdma_set_service_type() argument Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: perf/x86/intel/uncore: Fix NULL pointer dereference issue in upi_fill_topology() Get logical socket id instead of physical id in discover_upi_topology() to avoid out-of-bound access on 'upi = &type->topology[nid][idx];' line that leads to NULL pointer dereference in upi_fill_topology()

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix NULL pointer dereference at hibernate During hibernate sequence the source context might not have a clk_mgr. So don't use it to look for DML2 support.

In the Linux kernel, the following vulnerability has been resolved: nvmet-tcp: Fix a kernel panic when host sends an invalid H2C PDU length If the host sends an H2CData command with an invalid DATAL, the kernel may crash in nvmet_tcp_build_pdu_iovec(). Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 lr : nvmet_tcp_io_work+0x6ac/0x718 [nvmet_tcp] Call trace: process_one_work+0x174/0x3c8 worker_thread+0x2d0/0x3e8 kthread+0x104/0x110 Fix the bug by raising a fatal error if DATAL isn't coherent with the packet size. Also, the PDU length should never exceed the MAXH2CDATA parameter which has been communicated to the host in nvmet_tcp_handle_icreq().