A vulnerability was found in D-Link DNS-120, DNR-202L, DNS-315L, DNS-320, DNS-320L, DNS-320LW, DNS-321, DNR-322L, DNS-323, DNS-325, DNS-326, DNS-327L, DNR-326, DNS-340L, DNS-343, DNS-345, DNS-726-4, DNS-1100-4, DNS-1200-05 and DNS-1550-04 up to 20240814. It has been declared as critical. This vulnerability affects the function cgi_FMT_R5_SpareDsk_DiskMGR of the file /cgi-bin/hd_config.cgi of the component HTTP POST Request Handler. The manipulation of the argument f_source_dev leads to command injection. The attack can be initiated remotely. The exploit has been disclosed to the public and may be used. NOTE: This vulnerability only affects products that are no longer supported by the maintainer. NOTE: Vendor was contacted early and confirmed that the product is end-of-life. It should be retired and replaced.

A vulnerability was found in D-Link DNS-120, DNR-202L, DNS-315L, DNS-320, DNS-320L, DNS-320LW, DNS-321, DNR-322L, DNS-323, DNS-325, DNS-326, DNS-327L, DNR-326, DNS-340L, DNS-343, DNS-345, DNS-726-4, DNS-1100-4, DNS-1200-05 and DNS-1550-04 up to 20240814. It has been rated as critical. This issue affects the function cgi_FMT_Std2R5_1st_DiskMGR of the file /cgi-bin/hd_config.cgi of the component HTTP POST Request Handler. The manipulation of the argument f_source_dev leads to command injection. The attack may be initiated remotely. The exploit has been disclosed to the public and may be used. NOTE: This vulnerability only affects products that are no longer supported by the maintainer. NOTE: Vendor was contacted early and confirmed that the product is end-of-life. It should be retired and replaced.

A vulnerability, which was classified as critical, was found in D-Link DNS-120, DNR-202L, DNS-315L, DNS-320, DNS-320L, DNS-320LW, DNS-321, DNR-322L, DNS-323, DNS-325, DNS-326, DNS-327L, DNR-326, DNS-340L, DNS-343, DNS-345, DNS-726-4, DNS-1100-4, DNS-1200-05 and DNS-1550-04 up to 20240814. Affected is the function cgi_s3_modify of the file /cgi-bin/s3.cgi of the component HTTP POST Request Handler. The manipulation of the argument f_job_name leads to command injection. It is possible to launch the attack remotely. The exploit has been disclosed to the public and may be used. NOTE: This vulnerability only affects products that are no longer supported by the maintainer. NOTE: Vendor was contacted early and confirmed that the product is end-of-life. It should be retired and replaced.

A vulnerability was found in D-Link DNS-120, DNR-202L, DNS-315L, DNS-320, DNS-320L, DNS-320LW, DNS-321, DNR-322L, DNS-323, DNS-325, DNS-326, DNS-327L, DNR-326, DNS-340L, DNS-343, DNS-345, DNS-726-4, DNS-1100-4, DNS-1200-05 and DNS-1550-04 up to 20240814. It has been classified as critical. This affects the function webdav_mgr of the file /cgi-bin/webdav_mgr.cgi of the component HTTP POST Request Handler. The manipulation of the argument f_path leads to command injection. It is possible to initiate the attack remotely. The exploit has been disclosed to the public and may be used. NOTE: This vulnerability only affects products that are no longer supported by the maintainer. NOTE: Vendor was contacted early and confirmed that the product is end-of-life. It should be retired and replaced.

A vulnerability was found in D-Link DCS-931L up to 1.13.0. Impacted is the function doSystem of the file /setSystemAdmin. Performing a manipulation of the argument AdminID results in command injection. The attack may be initiated remotely. The exploit has been made public and could be used. This vulnerability only affects products that are no longer supported by the maintainer.

A weakness has been identified in D-Link DIR-823X 250416. This vulnerability affects the function sub_420688 of the file /goform/set_qos. Executing a manipulation can lead to os command injection. The attack can be executed remotely. The exploit has been made available to the public and could be used for attacks.

A vulnerability was detected in D-Link DI-7100G C1 24.04.18D1. Affected by this issue is the function set_jhttpd_info. Performing a manipulation of the argument usb_username results in command injection. Remote exploitation of the attack is possible.

A vulnerability has been found in D-Link DWR-M921 1.1.50. This impacts an unknown function of the file /boafrm/formLtefotaUpgradeFibocom. Such manipulation of the argument fota_url leads to command injection. It is possible to launch the attack remotely. The exploit has been disclosed to the public and may be used.

A vulnerability has been found in D-Link DIR-823X 250416. This affects the function sub_4211C8 of the file /goform/set_filtering. Such manipulation leads to os command injection. The attack may be launched remotely. The exploit has been disclosed to the public and may be used.

A vulnerability was found in D-Link DIR-615 4.10. This vulnerability affects unknown code of the file adv_routing.php of the component Web Configuration Interface. Performing a manipulation of the argument dest_ip/ submask/ gw results in os command injection. The attack may be initiated remotely. The exploit has been made public and could be used. This vulnerability only affects products that are no longer supported by the maintainer.

An issue was discovered on D-Link DCS-1130 devices. The device provides a user with the capability of setting a SMB folder for the video clippings recorded by the device. It seems that the POST parameters passed in this request (to test if email credentials and hostname sent to the device work properly) result in being passed as commands to a "system" API in the function and thus result in command injection on the device. If the firmware version is dissected using binwalk tool, we obtain a cramfs-root archive which contains the filesystem set up on the device that contains all the binaries. The library "libmailutils.so" is the one that has the vulnerable function "sub_1FC4" that receives the values sent by the POST request. If we open this binary in IDA-pro we will notice that this follows an ARM little endian format. The function sub_1FC4 in IDA pro is identified to be receiving the values sent in the POST request and the value set in POST parameter "receiver1" is extracted in function "sub_15AC" which is then passed to the vulnerable system API call. The vulnerable library function is accessed in "cgibox" binary at address 0x0008F598 which calls the "mailLoginTest" function in "libmailutils.so" binary as shown below which results in the vulnerable POST parameter being passed to the library which results in the command injection issue.

A security flaw has been discovered in D-Link DIR-823X 250416. The affected element is the function sub_4208A0 of the file /goform/set_dmz of the component Configuration Handler. The manipulation of the argument dmz_host/dmz_enable results in os command injection. The attack can be executed remotely. The exploit has been released to the public and may be used for attacks.

A weakness has been identified in D-Link DIR-823X 250416. This vulnerability affects the function sub_420618 of the file /goform/set_upnp. This manipulation of the argument upnp_enable causes os command injection. Remote exploitation of the attack is possible. The exploit has been made available to the public and could be used for attacks.

A vulnerability has been found in D-Link DIR-615 4.10. This affects an unknown part of the file adv_firewall.php of the component DMZ Host Feature. Such manipulation of the argument dmz_ipaddr  leads to os command injection. The attack can be launched remotely. The exploit has been disclosed to the public and may be used. This vulnerability only affects products that are no longer supported by the maintainer.

A vulnerability was identified in D-Link DIR-600 up to 2.15WWb02. This vulnerability affects unknown code of the file ssdp.cgi. Such manipulation of the argument HTTP_ST/REMOTE_ADDR/REMOTE_PORT/SERVER_ID leads to command injection. The attack may be launched remotely. The exploit is publicly available and might be used. This vulnerability only affects products that are no longer supported by the maintainer.

A security vulnerability has been detected in D-Link DIR-823X 250416. This issue affects some unknown processing of the file /goform/set_ddns of the component DDNS Service. The manipulation of the argument ddnsType/ddnsDomainName/ddnsUserName/ddnsPwd leads to os command injection. The attack is possible to be carried out remotely. The exploit has been disclosed publicly and may be used.

An issue was discovered on D-Link DCS-1100 and DCS-1130 devices. The device runs a custom daemon on UDP port 5978 which is called "dldps2121" and listens for broadcast packets sent on 255.255.255.255. This daemon handles custom D-Link UDP based protocol that allows D-Link mobile applications and desktop applications to discover D-Link devices on the local network. The binary processes the received UDP packets sent from any device in "main" function. One path in the function traverses towards a block of code that handles commands to be executed on the device. The custom protocol created by D-Link follows the following pattern: Packetlen, Type of packet; M=MAC address of device or broadcast; D=Device Type;C=base64 encoded command string;test=1111. If a packet is received with the packet type being "S" or 0x53 then the string passed in the "C" parameter is base64 decoded and then executed by passing into a System API. We can see at address 0x00009B44 that the string received in packet type subtracts 0x31 or "1" from the packet type and is compared against 0x22 or "double quotes". If that is the case, then the packet is sent towards the block of code that executes a command. Then the value stored in "C" parameter is extracted at address 0x0000A1B0. Finally, the string received is base 64 decoded and passed on to the system API at address 0x0000A2A8 as shown below. The same form of communication can be initiated by any process including an attacker process on the mobile phone or the desktop and this allows a third-party application on the device to execute commands on the device without any authentication by sending just 1 UDP packet with custom base64 encoding.

A vulnerability was found in D-Link DCS-931L up to 1.13.0. This affects an unknown part of the file /goform/setSysAdmin. The manipulation of the argument AdminID results in os command injection. The attack can be executed remotely. The exploit has been made public and could be used. This vulnerability only affects products that are no longer supported by the maintainer.

A security vulnerability has been detected in D-Link DIR-823X 250416. This affects the function sub_4175CC of the file /goform/set_static_route_table. Such manipulation of the argument interface/destip/netmask/gateway/metric leads to os command injection. The attack may be performed from remote. The exploit has been disclosed publicly and may be used.

An issue was discovered on D-Link DCS-1130 devices. The device provides a user with the capability of setting a SMB folder for the video clippings recorded by the device. It seems that the POST parameters passed in this request (to test if email credentials and hostname sent to the device work properly) result in being passed as commands to a "system" API in the function and thus result in command injection on the device. If the firmware version is dissected using binwalk tool, we obtain a cramfs-root archive which contains the filesystem set up on the device that contains all the binaries. The library "libmailutils.so" is the one that has the vulnerable function "sub_1FC4" that receives the values sent by the POST request. If we open this binary in IDA-pro we will notice that this follows an ARM little endian format. The function sub_1FC4 in IDA pro is identified to be receiving the values sent in the POST request and the value set in POST parameter "receiver1" is extracted in function "sub_15AC" which is then passed to the vulnerable system API call. The vulnerable library function is accessed in "cgibox" binary at address 0x00023BCC which calls the "Send_mail" function in "libmailutils.so" binary as shown below which results in the vulnerable POST parameter being passed to the library which results in the command injection issue.

A flaw has been found in D-Link DWR-M921 1.1.50. This affects the function sub_419920 of the file /boafrm/formLtefotaUpgradeQuectel. This manipulation of the argument fota_url causes command injection. It is possible to initiate the attack remotely. The exploit has been published and may be used.

An issue was discovered on D-Link DCS-1130 devices. The device provides a user with the capability of setting a SMB folder for the video clippings recorded by the device. It seems that the GET parameters passed in this request (to test if SMB credentials and hostname sent to the device work properly) result in being passed as commands to a "system" API in the function and thus result in command injection on the device. If the firmware version is dissected using binwalk tool, we obtain a cramfs-root archive which contains the filesystem set up on the device that contains all the binaries. The binary "cgibox" is the one that has the vulnerable function "sub_7EAFC" that receives the values sent by the GET request. If we open this binary in IDA-pro we will notice that this follows a ARM little endian format. The function sub_7EAFC in IDA pro is identified to be receiving the values sent in the GET request and the value set in GET parameter "user" is extracted in function sub_7E49C which is then passed to the vulnerable system API call.

A flaw has been found in D-Link DI-7100G C1 24.04.18D1. This affects the function start_proxy_client_email. Executing a manipulation can lead to command injection. The attack can be executed remotely. The exploit has been published and may be used.

A vulnerability was determined in D-Link DCS-933L up to 1.14.11. This affects an unknown function of the file /setSystemAdmin of the component alphapd. This manipulation of the argument AdminID causes command injection. Remote exploitation of the attack is possible. The exploit has been publicly disclosed and may be utilized. This vulnerability only affects products that are no longer supported by the maintainer.

A vulnerability was identified in D-Link DIR-823X 250416. The impacted element is an unknown function of the file /goform/set_mac_clone. Such manipulation of the argument mac leads to os command injection. The attack may be performed from remote. The exploit is publicly available and might be used.

A vulnerability was found in D-Link DIR-823X 250416. Affected by this issue is some unknown functionality of the file /goform/set_ac_status. Performing a manipulation of the argument ac_ipaddr/ac_ipstatus/ap_randtime results in os command injection. The attack may be initiated remotely. The exploit has been made public and could be used.

A security vulnerability has been detected in D-Link DWR-M921 1.1.50. Affected is the function sub_419F20 of the file /boafrm/formUSSDSetup of the component USSD Configuration Endpoint. The manipulation of the argument ussdValue leads to command injection. The attack can be initiated remotely. The exploit has been disclosed publicly and may be used.

A vulnerability was determined in D-Link DIR-823X 250416. Affected by this issue is the function sub_424D20 of the file /goform/set_ipv6. Executing a manipulation can lead to os command injection. It is possible to launch the attack remotely. The exploit has been publicly disclosed and may be utilized.

A vulnerability was determined in D-Link DIR-823X 250416. The affected element is an unknown function of the file /goform/set_password. This manipulation of the argument http_passwd causes os command injection. The attack is possible to be carried out remotely. The exploit has been publicly disclosed and may be utilized.

A weakness has been identified in D-Link DIR-823X 250416. Affected by this issue is the function sub_412E7C of the file /goform/set_wifidog_settings. Executing a manipulation of the argument wd_enable can lead to command injection. The attack can be executed remotely. The exploit has been made available to the public and could be used for attacks.

A vulnerability was identified in D-Link DIR-823X 250416. This affects an unknown function of the file /goform/set_server_settings of the component Configuration Parameter Handler. The manipulation of the argument terminal_addr/server_ip/server_port leads to os command injection. The attack may be initiated remotely. The exploit is publicly available and might be used.

A vulnerability was detected in D-Link DIR-615 up to 4.10. This impacts an unknown function of the file /wiz_policy_3_machine.php of the component Web Management Interface. Performing a manipulation of the argument ipaddr results in os command injection. It is possible to initiate the attack remotely. The exploit is now public and may be used. This vulnerability only affects products that are no longer supported by the maintainer.

A weakness has been identified in D-Link DCS700l 1.03.09. Affected is an unknown function of the file /setDayNightMode of the component Web Form Handler. Executing a manipulation of the argument LightSensorControl can lead to command injection. The attack may be launched remotely. The exploit has been made available to the public and could be used for attacks.

A vulnerability was determined in D-Link DIR-615 4.10. Impacted is an unknown function of the file /adv_mac_filter.php of the component MAC Filter Configuration. This manipulation of the argument mac causes os command injection. The attack is possible to be carried out remotely. The exploit has been publicly disclosed and may be utilized. This vulnerability only affects products that are no longer supported by the maintainer.

A flaw has been found in D-Link DWR-M961 1.1.47. This vulnerability affects the function sub_419920 of the file /boafrm/formLtefotaUpgradeQuectel. This manipulation of the argument fota_url causes command injection. The attack is possible to be carried out remotely. The exploit has been published and may be used.

An issue was discovered in D-Link DIR816_A1_FW101CNB04 750m11ac wireless router, The HTTP request parameter is used in the handler function of /goform/form2userconfig.cgi route, which can construct the user name string to delete the user function. This can lead to command injection through shell metacharacters.

A vulnerability was found in D-Link DIR-615 4.10. This issue affects some unknown processing of the file /set_temp_nodes.php of the component URL Filter. The manipulation results in os command injection. The attack can be executed remotely. The exploit has been made public and could be used. This vulnerability only affects products that are no longer supported by the maintainer.

A security flaw has been discovered in D-Link DIR-823X 250416. This vulnerability affects unknown code of the file /goform/set_ac_server of the component Web Management Interface. The manipulation of the argument ac_server results in os command injection. The attack can be launched remotely. The exploit has been released to the public and may be used for attacks.

An issue was discovered in D-Link DIR-816 DIR-816A2_FWv1.10CNB05_R1B011D88210 The HTTP request parameter is used in the handler function of /goform/form2userconfig.cgi route, which can construct the user name string to delete the user function. This can lead to command injection through shell metacharacters.

A weakness has been identified in D-Link DIR-823X 250416. This impacts an unknown function of the file /goform/set_language. Executing a manipulation of the argument langSelection can lead to os command injection. It is possible to launch the attack remotely. The exploit has been made available to the public and could be used for attacks.

A weakness has been identified in D-Link DIR-816L 206b01. Affected by this issue is the function soapcgi_main of the file /soap.cgi. This manipulation of the argument service causes os command injection. Remote exploitation of the attack is possible. The exploit has been made available to the public and could be exploited. This vulnerability only affects products that are no longer supported by the maintainer.

A security vulnerability has been detected in D-Link DIR-852 1.00CN B09. Impacted is the function soapcgi_main of the file soap.cgi of the component SOAP Service. Such manipulation of the argument service leads to os command injection. The attack can be launched remotely. The exploit has been disclosed publicly and may be used. This vulnerability only affects products that are no longer supported by the maintainer.

A security flaw has been discovered in D-Link DI-7400G+ 19.12.25A1. Affected is the function sub_478D28 of the file /mng_platform.asp. The manipulation of the argument addr with the input `echo 12345 > poc.txt` results in command injection. An attack on the physical device is feasible. The exploit has been released to the public and may be exploited.

A security vulnerability has been detected in D-Link DI-500WF 14.04.10A1T. The impacted element is an unknown function of the file /version_upgrade.asp of the component jhttpd. The manipulation of the argument path leads to os command injection. The attack may be initiated remotely. The exploit has been disclosed publicly and may be used.

A vulnerability was found in D-Link DI-8200G 17.12.20A1. This affects an unknown function of the file /upgrade_filter.asp. The manipulation of the argument path results in command injection. The attack may be performed from remote. The exploit has been made public and could be used.

A vulnerability was found in D-Link DIR‑818L up to 1.05B01. This issue affects the function getenv of the file /htdocs/cgibin of the component ssdpcgi. The manipulation leads to command injection. The attack may be initiated remotely. The exploit has been disclosed to the public and may be used.

D-LINK DI-8400 v16.07.26A1 was discovered to contain multiple remote command execution (RCE) vulnerabilities in the msp_info_htm function via the flag and cmd parameters.

D-Link DIR-820L 1.05b03 was discovered to contain a remote code execution (RCE) vulnerability via the ping_addr parameter in the ping_v4 and ping_v6 functions.