In the Linux kernel, the following vulnerability has been resolved: gpiolib: Fix crash on error in gpiochip_get_ngpios() The gpiochip_get_ngpios() uses chip_*() macros to print messages. However these macros rely on gpiodev to be initialised and set, which is not the case when called via bgpio_init(). In such a case the printing messages will crash on NULL pointer dereference. Replace chip_*() macros by the respective dev_*() ones to avoid such crash.

In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Reject Hyper-V's SEND_IPI hypercalls if local APIC isn't in-kernel Advertise support for Hyper-V's SEND_IPI and SEND_IPI_EX hypercalls if and only if the local API is emulated/virtualized by KVM, and explicitly reject said hypercalls if the local APIC is emulated in userspace, i.e. don't rely on userspace to opt-in to KVM_CAP_HYPERV_ENFORCE_CPUID. Rejecting SEND_IPI and SEND_IPI_EX fixes a NULL-pointer dereference if Hyper-V enlightenments are exposed to the guest without an in-kernel local APIC: dump_stack+0xbe/0xfd __kasan_report.cold+0x34/0x84 kasan_report+0x3a/0x50 __apic_accept_irq+0x3a/0x5c0 kvm_hv_send_ipi.isra.0+0x34e/0x820 kvm_hv_hypercall+0x8d9/0x9d0 kvm_emulate_hypercall+0x506/0x7e0 __vmx_handle_exit+0x283/0xb60 vmx_handle_exit+0x1d/0xd0 vcpu_enter_guest+0x16b0/0x24c0 vcpu_run+0xc0/0x550 kvm_arch_vcpu_ioctl_run+0x170/0x6d0 kvm_vcpu_ioctl+0x413/0xb20 __se_sys_ioctl+0x111/0x160 do_syscal1_64+0x30/0x40 entry_SYSCALL_64_after_hwframe+0x67/0xd1 Note, checking the sending vCPU is sufficient, as the per-VM irqchip_mode can't be modified after vCPUs are created, i.e. if one vCPU has an in-kernel local APIC, then all vCPUs have an in-kernel local APIC.

In the Linux kernel, the following vulnerability has been resolved: sctp: sysctl: auth_enable: avoid using current->nsproxy As mentioned in a previous commit of this series, using the 'net' structure via 'current' is not recommended for different reasons: - Inconsistency: getting info from the reader's/writer's netns vs only from the opener's netns. - current->nsproxy can be NULL in some cases, resulting in an 'Oops' (null-ptr-deref), e.g. when the current task is exiting, as spotted by syzbot [1] using acct(2). The 'net' structure can be obtained from the table->data using container_of(). Note that table->data could also be used directly, but that would increase the size of this fix, while 'sctp.ctl_sock' still needs to be retrieved from 'net' structure.

In the Linux kernel, the following vulnerability has been resolved: drm/xe/hmm: Don't dereference struct page pointers without notifier lock The pnfs that we obtain from hmm_range_fault() point to pages that we don't have a reference on, and the guarantee that they are still in the cpu page-tables is that the notifier lock must be held and the notifier seqno is still valid. So while building the sg table and marking the pages accesses / dirty we need to hold this lock with a validated seqno. However, the lock is reclaim tainted which makes sg_alloc_table_from_pages_segment() unusable, since it internally allocates memory. Instead build the sg-table manually. For the non-iommu case this might lead to fewer coalesces, but if that's a problem it can be fixed up later in the resource cursor code. For the iommu case, the whole sg-table may still be coalesced to a single contigous device va region. This avoids marking pages that we don't own dirty and accessed, and it also avoid dereferencing struct pages that we don't own. v2: - Use assert to check whether hmm pfns are valid (Matthew Auld) - Take into account that large pages may cross range boundaries (Matthew Auld) v3: - Don't unnecessarily check for a non-freed sg-table. (Matthew Auld) - Add a missing up_read() in an error path. (Matthew Auld) (cherry picked from commit ea3e66d280ce2576664a862693d1da8fd324c317)

In the Linux kernel, the following vulnerability has been resolved: w1: fix NULL pointer dereference in probe The w1_uart_probe() function calls w1_uart_serdev_open() (which includes devm_serdev_device_open()) before setting the client ops via serdev_device_set_client_ops(). This ordering can trigger a NULL pointer dereference in the serdev controller's receive_buf handler, as it assumes serdev->ops is valid when SERPORT_ACTIVE is set. This is similar to the issue fixed in commit 5e700b384ec1 ("platform/chrome: cros_ec_uart: properly fix race condition") where devm_serdev_device_open() was called before fully initializing the device. Fix the race by ensuring client ops are set before enabling the port via w1_uart_serdev_open().

In the Linux kernel, the following vulnerability has been resolved: vsock: prevent null-ptr-deref in vsock_*[has_data|has_space] Recent reports have shown how we sometimes call vsock_*_has_data() when a vsock socket has been de-assigned from a transport (see attached links), but we shouldn't. Previous commits should have solved the real problems, but we may have more in the future, so to avoid null-ptr-deref, we can return 0 (no space, no data available) but with a warning. This way the code should continue to run in a nearly consistent state and have a warning that allows us to debug future problems.

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7921: fix kernel panic due to null pointer dereference Address a kernel panic caused by a null pointer dereference in the `mt792x_rx_get_wcid` function. The issue arises because the `deflink` structure is not properly initialized with the `sta` context. This patch ensures that the `deflink` structure is correctly linked to the `sta` context, preventing the null pointer dereference. BUG: kernel NULL pointer dereference, address: 0000000000000400 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 0 UID: 0 PID: 470 Comm: mt76-usb-rx phy Not tainted 6.12.13-gentoo-dist #1 Hardware name: /AMD HUDSON-M1, BIOS 4.6.4 11/15/2011 RIP: 0010:mt792x_rx_get_wcid+0x48/0x140 [mt792x_lib] RSP: 0018:ffffa147c055fd98 EFLAGS: 00010202 RAX: 0000000000000000 RBX: ffff8e9ecb652000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffff8e9ecb652000 RBP: 0000000000000685 R08: ffff8e9ec6570000 R09: 0000000000000000 R10: ffff8e9ecd2ca000 R11: ffff8e9f22a217c0 R12: 0000000038010119 R13: 0000000080843801 R14: ffff8e9ec6570000 R15: ffff8e9ecb652000 FS: 0000000000000000(0000) GS:ffff8e9f22a00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000400 CR3: 000000000d2ea000 CR4: 00000000000006f0 Call Trace: <TASK> ? __die_body.cold+0x19/0x27 ? page_fault_oops+0x15a/0x2f0 ? search_module_extables+0x19/0x60 ? search_bpf_extables+0x5f/0x80 ? exc_page_fault+0x7e/0x180 ? asm_exc_page_fault+0x26/0x30 ? mt792x_rx_get_wcid+0x48/0x140 [mt792x_lib] mt7921_queue_rx_skb+0x1c6/0xaa0 [mt7921_common] mt76u_alloc_queues+0x784/0x810 [mt76_usb] ? __pfx___mt76_worker_fn+0x10/0x10 [mt76] __mt76_worker_fn+0x4f/0x80 [mt76] kthread+0xd2/0x100 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x34/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> ---[ end trace 0000000000000000 ]---

In the Linux kernel, the following vulnerability has been resolved: btrfs: avoid NULL pointer dereference if no valid extent tree [BUG] Syzbot reported a crash with the following call trace: BTRFS info (device loop0): scrub: started on devid 1 BUG: kernel NULL pointer dereference, address: 0000000000000208 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 106e70067 P4D 106e70067 PUD 107143067 PMD 0 Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 1 UID: 0 PID: 689 Comm: repro Kdump: loaded Tainted: G O 6.13.0-rc4-custom+ #206 Tainted: [O]=OOT_MODULE Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS unknown 02/02/2022 RIP: 0010:find_first_extent_item+0x26/0x1f0 [btrfs] Call Trace: <TASK> scrub_find_fill_first_stripe+0x13d/0x3b0 [btrfs] scrub_simple_mirror+0x175/0x260 [btrfs] scrub_stripe+0x5d4/0x6c0 [btrfs] scrub_chunk+0xbb/0x170 [btrfs] scrub_enumerate_chunks+0x2f4/0x5f0 [btrfs] btrfs_scrub_dev+0x240/0x600 [btrfs] btrfs_ioctl+0x1dc8/0x2fa0 [btrfs] ? do_sys_openat2+0xa5/0xf0 __x64_sys_ioctl+0x97/0xc0 do_syscall_64+0x4f/0x120 entry_SYSCALL_64_after_hwframe+0x76/0x7e </TASK> [CAUSE] The reproducer is using a corrupted image where extent tree root is corrupted, thus forcing to use "rescue=all,ro" mount option to mount the image. Then it triggered a scrub, but since scrub relies on extent tree to find where the data/metadata extents are, scrub_find_fill_first_stripe() relies on an non-empty extent root. But unfortunately scrub_find_fill_first_stripe() doesn't really expect an NULL pointer for extent root, it use extent_root to grab fs_info and triggered a NULL pointer dereference. [FIX] Add an extra check for a valid extent root at the beginning of scrub_find_fill_first_stripe(). The new error path is introduced by 42437a6386ff ("btrfs: introduce mount option rescue=ignorebadroots"), but that's pretty old, and later commit b979547513ff ("btrfs: scrub: introduce helper to find and fill sector info for a scrub_stripe") changed how we do scrub. So for kernels older than 6.6, the fix will need manual backport.

In the Linux kernel, the following vulnerability has been resolved: can: etas_es58x: fix potential NULL pointer dereference on udev->serial The driver assumed that es58x_dev->udev->serial could never be NULL. While this is true on commercially available devices, an attacker could spoof the device identity providing a NULL USB serial number. That would trigger a NULL pointer dereference. Add a check on es58x_dev->udev->serial before accessing it.

In the Linux kernel, the following vulnerability has been resolved: driver core: class: Fix wild pointer dereferences in API class_dev_iter_next() There are a potential wild pointer dereferences issue regarding APIs class_dev_iter_(init|next|exit)(), as explained by below typical usage: // All members of @iter are wild pointers. struct class_dev_iter iter; // class_dev_iter_init(@iter, @class, ...) checks parameter @class for // potential class_to_subsys() error, and it returns void type and does // not initialize its output parameter @iter, so caller can not detect // the error and continues to invoke class_dev_iter_next(@iter) even if // @iter still contains wild pointers. class_dev_iter_init(&iter, ...); // Dereference these wild pointers in @iter here once suffer the error. while (dev = class_dev_iter_next(&iter)) { ... }; // Also dereference these wild pointers here. class_dev_iter_exit(&iter); Actually, all callers of these APIs have such usage pattern in kernel tree. Fix by: - Initialize output parameter @iter by memset() in class_dev_iter_init() and give callers prompt by pr_crit() for the error. - Check if @iter is valid in class_dev_iter_next().

In the Linux kernel, the following vulnerability has been resolved: scsi: qla1280: Fix kernel oops when debug level > 2 A null dereference or oops exception will eventually occur when qla1280.c driver is compiled with DEBUG_QLA1280 enabled and ql_debug_level > 2. I think its clear from the code that the intention here is sg_dma_len(s) not length of sg_next(s) when printing the debug info.

In the Linux kernel, the following vulnerability has been resolved: PCI: Fix NULL dereference in SR-IOV VF creation error path Clean up when virtfn setup fails to prevent NULL pointer dereference during device removal. The kernel oops below occurred due to incorrect error handling flow when pci_setup_device() fails. Add pci_iov_scan_device(), which handles virtfn allocation and setup and cleans up if pci_setup_device() fails, so pci_iov_add_virtfn() doesn't need to call pci_stop_and_remove_bus_device(). This prevents accessing partially initialized virtfn devices during removal. BUG: kernel NULL pointer dereference, address: 00000000000000d0 RIP: 0010:device_del+0x3d/0x3d0 Call Trace: pci_remove_bus_device+0x7c/0x100 pci_iov_add_virtfn+0xfa/0x200 sriov_enable+0x208/0x420 mlx5_core_sriov_configure+0x6a/0x160 [mlx5_core] sriov_numvfs_store+0xae/0x1a0 [bhelgaas: commit log, return ERR_PTR(-ENOMEM) directly]

In the Linux kernel, the following vulnerability has been resolved: wifi: brcmfmac: Check the return value of of_property_read_string_index() Somewhen between 6.10 and 6.11 the driver started to crash on my MacBookPro14,3. The property doesn't exist and 'tmp' remains uninitialized, so we pass a random pointer to devm_kstrdup(). The crash I am getting looks like this: BUG: unable to handle page fault for address: 00007f033c669379 PF: supervisor read access in kernel mode PF: error_code(0x0001) - permissions violation PGD 8000000101341067 P4D 8000000101341067 PUD 101340067 PMD 1013bb067 PTE 800000010aee9025 Oops: Oops: 0001 [#1] SMP PTI CPU: 4 UID: 0 PID: 827 Comm: (udev-worker) Not tainted 6.11.8-gentoo #1 Hardware name: Apple Inc. MacBookPro14,3/Mac-551B86E5744E2388, BIOS 529.140.2.0.0 06/23/2024 RIP: 0010:strlen+0x4/0x30 Code: f7 75 ec 31 c0 c3 cc cc cc cc 48 89 f8 c3 cc cc cc cc 0f 1f 40 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 f3 0f 1e fa <80> 3f 00 74 14 48 89 f8 48 83 c0 01 80 38 00 75 f7 48 29 f8 c3 cc RSP: 0018:ffffb4aac0683ad8 EFLAGS: 00010202 RAX: 00000000ffffffea RBX: 00007f033c669379 RCX: 0000000000000001 RDX: 0000000000000cc0 RSI: 00007f033c669379 RDI: 00007f033c669379 RBP: 00000000ffffffea R08: 0000000000000000 R09: 00000000c0ba916a R10: ffffffffffffffff R11: ffffffffb61ea260 R12: ffff91f7815b50c8 R13: 0000000000000cc0 R14: ffff91fafefffe30 R15: ffffb4aac0683b30 FS: 00007f033ccbe8c0(0000) GS:ffff91faeed00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f033c669379 CR3: 0000000107b1e004 CR4: 00000000003706f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? __die+0x23/0x70 ? page_fault_oops+0x149/0x4c0 ? raw_spin_rq_lock_nested+0xe/0x20 ? sched_balance_newidle+0x22b/0x3c0 ? update_load_avg+0x78/0x770 ? exc_page_fault+0x6f/0x150 ? asm_exc_page_fault+0x26/0x30 ? __pfx_pci_conf1_write+0x10/0x10 ? strlen+0x4/0x30 devm_kstrdup+0x25/0x70 brcmf_of_probe+0x273/0x350 [brcmfmac]

In the Linux kernel, the following vulnerability has been resolved: sctp: sysctl: plpmtud_probe_interval: avoid using current->nsproxy As mentioned in a previous commit of this series, using the 'net' structure via 'current' is not recommended for different reasons: - Inconsistency: getting info from the reader's/writer's netns vs only from the opener's netns. - current->nsproxy can be NULL in some cases, resulting in an 'Oops' (null-ptr-deref), e.g. when the current task is exiting, as spotted by syzbot [1] using acct(2). The 'net' structure can be obtained from the table->data using container_of(). Note that table->data could also be used directly, as this is the only member needed from the 'net' structure, but that would increase the size of this fix, to use '*data' everywhere 'net->sctp.probe_interval' is used.

In the Linux kernel, the following vulnerability has been resolved: arm64: Don't call NULL in do_compat_alignment_fixup() do_alignment_t32_to_handler() only fixes up alignment faults for specific instructions; it returns NULL otherwise (e.g. LDREX). When that's the case, signal to the caller that it needs to proceed with the regular alignment fault handling (i.e. SIGBUS). Without this patch, the kernel panics: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 Mem abort info: ESR = 0x0000000086000006 EC = 0x21: IABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x06: level 2 translation fault user pgtable: 4k pages, 48-bit VAs, pgdp=00000800164aa000 [0000000000000000] pgd=0800081fdbd22003, p4d=0800081fdbd22003, pud=08000815d51c6003, pmd=0000000000000000 Internal error: Oops: 0000000086000006 [#1] SMP Modules linked in: cfg80211 rfkill xt_nat xt_tcpudp xt_conntrack nft_chain_nat xt_MASQUERADE nf_nat nf_conntrack_netlink nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 xfrm_user xfrm_algo xt_addrtype nft_compat br_netfilter veth nvme_fa> libcrc32c crc32c_generic raid0 multipath linear dm_mod dax raid1 md_mod xhci_pci nvme xhci_hcd nvme_core t10_pi usbcore igb crc64_rocksoft crc64 crc_t10dif crct10dif_generic crct10dif_ce crct10dif_common usb_common i2c_algo_bit i2c> CPU: 2 PID: 3932954 Comm: WPEWebProcess Not tainted 6.1.0-31-arm64 #1 Debian 6.1.128-1 Hardware name: GIGABYTE MP32-AR1-00/MP32-AR1-00, BIOS F18v (SCP: 1.08.20211002) 12/01/2021 pstate: 80400009 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : 0x0 lr : do_compat_alignment_fixup+0xd8/0x3dc sp : ffff80000f973dd0 x29: ffff80000f973dd0 x28: ffff081b42526180 x27: 0000000000000000 x26: 0000000000000000 x25: 0000000000000000 x24: 0000000000000000 x23: 0000000000000004 x22: 0000000000000000 x21: 0000000000000001 x20: 00000000e8551f00 x19: ffff80000f973eb0 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000 x11: 0000000000000000 x10: 0000000000000000 x9 : ffffaebc949bc488 x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000000000 x5 : 0000000000400000 x4 : 0000fffffffffffe x3 : 0000000000000000 x2 : ffff80000f973eb0 x1 : 00000000e8551f00 x0 : 0000000000000001 Call trace: 0x0 do_alignment_fault+0x40/0x50 do_mem_abort+0x4c/0xa0 el0_da+0x48/0xf0 el0t_32_sync_handler+0x110/0x140 el0t_32_sync+0x190/0x194 Code: bad PC value ---[ end trace 0000000000000000 ]---

In the Linux kernel, the following vulnerability has been resolved: drm/xe: Fix tlb invalidation when wedging If GuC fails to load, the driver wedges, but in the process it tries to do stuff that may not be initialized yet. This moves the xe_gt_tlb_invalidation_init() to be done earlier: as its own doc says, it's a software-only initialization and should had been named with the _early() suffix. Move it to be called by xe_gt_init_early(), so the locks and seqno are initialized, avoiding a NULL ptr deref when wedging: xe 0000:03:00.0: [drm] *ERROR* GT0: load failed: status: Reset = 0, BootROM = 0x50, UKernel = 0x00, MIA = 0x00, Auth = 0x01 xe 0000:03:00.0: [drm] *ERROR* GT0: firmware signature verification failed xe 0000:03:00.0: [drm] *ERROR* CRITICAL: Xe has declared device 0000:03:00.0 as wedged. ... BUG: kernel NULL pointer dereference, address: 0000000000000000 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 9 UID: 0 PID: 3908 Comm: modprobe Tainted: G U W 6.13.0-rc4-xe+ #3 Tainted: [U]=USER, [W]=WARN Hardware name: Intel Corporation Alder Lake Client Platform/AlderLake-S ADP-S DDR5 UDIMM CRB, BIOS ADLSFWI1.R00.3275.A00.2207010640 07/01/2022 RIP: 0010:xe_gt_tlb_invalidation_reset+0x75/0x110 [xe] This can be easily triggered by poking the GuC binary to force a signature failure. There will still be an extra message, xe 0000:03:00.0: [drm] *ERROR* GT0: GuC mmio request 0x4100: no reply 0x4100 but that's better than a NULL ptr deref. (cherry picked from commit 5001ef3af8f2c972d6fd9c5221a8457556f8bea6)

In the Linux kernel, the following vulnerability has been resolved: sctp: sysctl: cookie_hmac_alg: avoid using current->nsproxy As mentioned in a previous commit of this series, using the 'net' structure via 'current' is not recommended for different reasons: - Inconsistency: getting info from the reader's/writer's netns vs only from the opener's netns. - current->nsproxy can be NULL in some cases, resulting in an 'Oops' (null-ptr-deref), e.g. when the current task is exiting, as spotted by syzbot [1] using acct(2). The 'net' structure can be obtained from the table->data using container_of(). Note that table->data could also be used directly, as this is the only member needed from the 'net' structure, but that would increase the size of this fix, to use '*data' everywhere 'net->sctp.sctp_hmac_alg' is used.

The mac80211 subsystem in the Linux kernel before 5.12.13, when a device supporting only 5 GHz is used, allows attackers to cause a denial of service (NULL pointer dereference in the radiotap parser) by injecting a frame with 802.11a rates.

In the Linux kernel, the following vulnerability has been resolved: net: Add rx_skb of kfree_skb to raw_tp_null_args[]. Yan Zhai reported a BPF prog could trigger a null-ptr-deref [0] in trace_kfree_skb if the prog does not check if rx_sk is NULL. Commit c53795d48ee8 ("net: add rx_sk to trace_kfree_skb") added rx_sk to trace_kfree_skb, but rx_sk is optional and could be NULL. Let's add kfree_skb to raw_tp_null_args[] to let the BPF verifier validate such a prog and prevent the issue. Now we fail to load such a prog: libbpf: prog 'drop': -- BEGIN PROG LOAD LOG -- 0: R1=ctx() R10=fp0 ; int BPF_PROG(drop, struct sk_buff *skb, void *location, @ kfree_skb_sk_null.bpf.c:21 0: (79) r3 = *(u64 *)(r1 +24) func 'kfree_skb' arg3 has btf_id 5253 type STRUCT 'sock' 1: R1=ctx() R3_w=trusted_ptr_or_null_sock(id=1) ; bpf_printk("sk: %d, %d\n", sk, sk->__sk_common.skc_family); @ kfree_skb_sk_null.bpf.c:24 1: (69) r4 = *(u16 *)(r3 +16) R3 invalid mem access 'trusted_ptr_or_null_' processed 2 insns (limit 1000000) max_states_per_insn 0 total_states 0 peak_states 0 mark_read 0 -- END PROG LOAD LOG -- Note this fix requires commit 838a10bd2ebf ("bpf: Augment raw_tp arguments with PTR_MAYBE_NULL"). [0]: BUG: kernel NULL pointer dereference, address: 0000000000000010 PF: supervisor read access in kernel mode PF: error_code(0x0000) - not-present page PGD 0 P4D 0 PREEMPT SMP RIP: 0010:bpf_prog_5e21a6db8fcff1aa_drop+0x10/0x2d Call Trace: <TASK> ? __die+0x1f/0x60 ? page_fault_oops+0x148/0x420 ? search_bpf_extables+0x5b/0x70 ? fixup_exception+0x27/0x2c0 ? exc_page_fault+0x75/0x170 ? asm_exc_page_fault+0x22/0x30 ? bpf_prog_5e21a6db8fcff1aa_drop+0x10/0x2d bpf_trace_run4+0x68/0xd0 ? unix_stream_connect+0x1f4/0x6f0 sk_skb_reason_drop+0x90/0x120 unix_stream_connect+0x1f4/0x6f0 __sys_connect+0x7f/0xb0 __x64_sys_connect+0x14/0x20 do_syscall_64+0x47/0xc30 entry_SYSCALL_64_after_hwframe+0x4b/0x53

In the Linux kernel, the following vulnerability has been resolved: netlabel: Fix NULL pointer exception caused by CALIPSO on IPv4 sockets When calling netlbl_conn_setattr(), addr->sa_family is used to determine the function behavior. If sk is an IPv4 socket, but the connect function is called with an IPv6 address, the function calipso_sock_setattr() is triggered. Inside this function, the following code is executed: sk_fullsock(__sk) ? inet_sk(__sk)->pinet6 : NULL; Since sk is an IPv4 socket, pinet6 is NULL, leading to a null pointer dereference. This patch fixes the issue by checking if inet6_sk(sk) returns a NULL pointer before accessing pinet6.

In the Linux kernel, the following vulnerability has been resolved: net: fix NULL pointer dereference in l3mdev_l3_rcv When delete l3s ipvlan: ip link del link eth0 ipvlan1 type ipvlan mode l3s This may cause a null pointer dereference: Call trace: ip_rcv_finish+0x48/0xd0 ip_rcv+0x5c/0x100 __netif_receive_skb_one_core+0x64/0xb0 __netif_receive_skb+0x20/0x80 process_backlog+0xb4/0x204 napi_poll+0xe8/0x294 net_rx_action+0xd8/0x22c __do_softirq+0x12c/0x354 This is because l3mdev_l3_rcv() visit dev->l3mdev_ops after ipvlan_l3s_unregister() assign the dev->l3mdev_ops to NULL. The process like this: (CPU1) | (CPU2) l3mdev_l3_rcv() | check dev->priv_flags: | master = skb->dev; | | | ipvlan_l3s_unregister() | set dev->priv_flags | dev->l3mdev_ops = NULL; | visit master->l3mdev_ops | To avoid this by do not set dev->l3mdev_ops when unregister l3s ipvlan.

In the Linux kernel, the following vulnerability has been resolved: staging: gpib: Fix Oops after disconnect in ni_usb If the usb dongle is disconnected subsequent calls to the driver cause a NULL dereference Oops as the bus_interface is set to NULL on disconnect. This problem was introduced by setting usb_dev from the bus_interface for dev_xxx messages. Previously bus_interface was checked for NULL only in the the functions directly calling usb_fill_bulk_urb or usb_control_msg. Check for valid bus_interface on all interface entry points and return -ENODEV if it is NULL.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: Add check for mgmt_alloc_skb() in mgmt_remote_name() Add check for the return value of mgmt_alloc_skb() in mgmt_remote_name() to prevent null pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: nfp: bpf: Add check for nfp_app_ctrl_msg_alloc() Add check for the return value of nfp_app_ctrl_msg_alloc() in nfp_bpf_cmsg_alloc() to prevent null pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: fix missing .is_two_pixels_per_container Starting from 6.11, AMDGPU driver, while being loaded with amdgpu.dc=1, due to lack of .is_two_pixels_per_container function in dce60_tg_funcs, causes a NULL pointer dereference on PCs with old GPUs, such as R9 280X. So this fix adds missing .is_two_pixels_per_container to dce60_tg_funcs. (cherry picked from commit bd4b125eb949785c6f8a53b0494e32795421209d)

A NULL pointer dereference flaw was found in the Linux kernel’s KVM module, which can lead to a denial of service in the x86_emulate_insn in arch/x86/kvm/emulate.c. This flaw occurs while executing an illegal instruction in guest in the Intel CPU.

A NULL pointer dereference flaw was found in the Linux kernel’s IEEE 802.15.4 wireless networking subsystem in the way the user closes the LR-WPAN connection. This flaw allows a local user to crash the system. The highest threat from this vulnerability is to system availability.

In the Linux kernel, the following vulnerability has been resolved: sockmap, vsock: For connectible sockets allow only connected sockmap expects all vsocks to have a transport assigned, which is expressed in vsock_proto::psock_update_sk_prot(). However, there is an edge case where an unconnected (connectible) socket may lose its previously assigned transport. This is handled with a NULL check in the vsock/BPF recv path. Another design detail is that listening vsocks are not supposed to have any transport assigned at all. Which implies they are not supported by the sockmap. But this is complicated by the fact that a socket, before switching to TCP_LISTEN, may have had some transport assigned during a failed connect() attempt. Hence, we may end up with a listening vsock in a sockmap, which blows up quickly: KASAN: null-ptr-deref in range [0x0000000000000120-0x0000000000000127] CPU: 7 UID: 0 PID: 56 Comm: kworker/7:0 Not tainted 6.14.0-rc1+ Workqueue: vsock-loopback vsock_loopback_work RIP: 0010:vsock_read_skb+0x4b/0x90 Call Trace: sk_psock_verdict_data_ready+0xa4/0x2e0 virtio_transport_recv_pkt+0x1ca8/0x2acc vsock_loopback_work+0x27d/0x3f0 process_one_work+0x846/0x1420 worker_thread+0x5b3/0xf80 kthread+0x35a/0x700 ret_from_fork+0x2d/0x70 ret_from_fork_asm+0x1a/0x30 For connectible sockets, instead of relying solely on the state of vsk->transport, tell sockmap to only allow those representing established connections. This aligns with the behaviour for AF_INET and AF_UNIX.

In the Linux kernel, the following vulnerability has been resolved: iommu/vt-d: Avoid use of NULL after WARN_ON_ONCE There is a WARN_ON_ONCE to catch an unlikely situation when domain_remove_dev_pasid can't find the `pasid`. In case it nevertheless happens we must avoid using a NULL pointer.

In the Linux kernel, the following vulnerability has been resolved: ASoC: imx-card: Add NULL check in imx_card_probe() devm_kasprintf() returns NULL when memory allocation fails. Currently, imx_card_probe() does not check for this case, which results in a NULL pointer dereference. Add NULL check after devm_kasprintf() to prevent this issue.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Bridge, fix the crash caused by LAG state check When removing LAG device from bridge, NETDEV_CHANGEUPPER event is triggered. Driver finds the lower devices (PFs) to flush all the offloaded entries. And mlx5_lag_is_shared_fdb is checked, it returns false if one of PF is unloaded. In such case, mlx5_esw_bridge_lag_rep_get() and its caller return NULL, instead of the alive PF, and the flush is skipped. Besides, the bridge fdb entry's lastuse is updated in mlx5 bridge event handler. But this SWITCHDEV_FDB_ADD_TO_BRIDGE event can be ignored in this case because the upper interface for bond is deleted, and the entry will never be aged because lastuse is never updated. To make things worse, as the entry is alive, mlx5 bridge workqueue keeps sending that event, which is then handled by kernel bridge notifier. It causes the following crash when accessing the passed bond netdev which is already destroyed. To fix this issue, remove such checks. LAG state is already checked in commit 15f8f168952f ("net/mlx5: Bridge, verify LAG state when adding bond to bridge"), driver still need to skip offload if LAG becomes invalid state after initialization. Oops: stack segment: 0000 [#1] SMP CPU: 3 UID: 0 PID: 23695 Comm: kworker/u40:3 Tainted: G OE 6.11.0_mlnx #1 Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 Workqueue: mlx5_bridge_wq mlx5_esw_bridge_update_work [mlx5_core] RIP: 0010:br_switchdev_event+0x2c/0x110 [bridge] Code: 44 00 00 48 8b 02 48 f7 00 00 02 00 00 74 69 41 54 55 53 48 83 ec 08 48 8b a8 08 01 00 00 48 85 ed 74 4a 48 83 fe 02 48 89 d3 <4c> 8b 65 00 74 23 76 49 48 83 fe 05 74 7e 48 83 fe 06 75 2f 0f b7 RSP: 0018:ffffc900092cfda0 EFLAGS: 00010297 RAX: ffff888123bfe000 RBX: ffffc900092cfe08 RCX: 00000000ffffffff RDX: ffffc900092cfe08 RSI: 0000000000000001 RDI: ffffffffa0c585f0 RBP: 6669746f6e690a30 R08: 0000000000000000 R09: ffff888123ae92c8 R10: 0000000000000000 R11: fefefefefefefeff R12: ffff888123ae9c60 R13: 0000000000000001 R14: ffffc900092cfe08 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff88852c980000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f15914c8734 CR3: 0000000002830005 CR4: 0000000000770ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> ? __die_body+0x1a/0x60 ? die+0x38/0x60 ? do_trap+0x10b/0x120 ? do_error_trap+0x64/0xa0 ? exc_stack_segment+0x33/0x50 ? asm_exc_stack_segment+0x22/0x30 ? br_switchdev_event+0x2c/0x110 [bridge] ? sched_balance_newidle.isra.149+0x248/0x390 notifier_call_chain+0x4b/0xa0 atomic_notifier_call_chain+0x16/0x20 mlx5_esw_bridge_update+0xec/0x170 [mlx5_core] mlx5_esw_bridge_update_work+0x19/0x40 [mlx5_core] process_scheduled_works+0x81/0x390 worker_thread+0x106/0x250 ? bh_worker+0x110/0x110 kthread+0xb7/0xe0 ? kthread_park+0x80/0x80 ret_from_fork+0x2d/0x50 ? kthread_park+0x80/0x80 ret_from_fork_asm+0x11/0x20 </TASK>

In the Linux kernel, the following vulnerability has been resolved: drm/msm: Fix null ptr access msm_ioctl_gem_submit() Fix the below null pointer dereference in msm_ioctl_gem_submit(): 26545.260705: Call trace: 26545.263223: kref_put+0x1c/0x60 26545.266452: msm_ioctl_gem_submit+0x254/0x744 26545.270937: drm_ioctl_kernel+0xa8/0x124 26545.274976: drm_ioctl+0x21c/0x33c 26545.278478: drm_compat_ioctl+0xdc/0xf0 26545.282428: __arm64_compat_sys_ioctl+0xc8/0x100 26545.287169: el0_svc_common+0xf8/0x250 26545.291025: do_el0_svc_compat+0x28/0x54 26545.295066: el0_svc_compat+0x10/0x1c 26545.298838: el0_sync_compat_handler+0xa8/0xcc 26545.303403: el0_sync_compat+0x188/0x1c0 26545.307445: Code: d503201f d503201f 52800028 4b0803e8 (b8680008) 26545.318799: Kernel panic - not syncing: Oops: Fatal exception

In the Linux kernel, the following vulnerability has been resolved: HID: amd_sfh: Fix potential NULL pointer dereference devm_add_action_or_reset() can suddenly invoke amd_mp2_pci_remove() at registration that will cause NULL pointer dereference since corresponding data is not initialized yet. The patch moves initialization of data before devm_add_action_or_reset(). Found by Linux Driver Verification project (linuxtesting.org). [jkosina@suse.cz: rebase]

In the Linux kernel, the following vulnerability has been resolved: scsi: core: Fix bad pointer dereference when ehandler kthread is invalid Commit 66a834d09293 ("scsi: core: Fix error handling of scsi_host_alloc()") changed the allocation logic to call put_device() to perform host cleanup with the assumption that IDA removal and stopping the kthread would properly be performed in scsi_host_dev_release(). However, in the unlikely case that the error handler thread fails to spawn, shost->ehandler is set to ERR_PTR(-ENOMEM). The error handler cleanup code in scsi_host_dev_release() will call kthread_stop() if shost->ehandler != NULL which will always be the case whether the kthread was successfully spawned or not. In the case that it failed to spawn this has the nasty side effect of trying to dereference an invalid pointer when kthread_stop() is called. The following splat provides an example of this behavior in the wild: scsi host11: error handler thread failed to spawn, error = -4 Kernel attempted to read user page (10c) - exploit attempt? (uid: 0) BUG: Kernel NULL pointer dereference on read at 0x0000010c Faulting instruction address: 0xc00000000818e9a8 Oops: Kernel access of bad area, sig: 11 [#1] LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries Modules linked in: ibmvscsi(+) scsi_transport_srp dm_multipath dm_mirror dm_region hash dm_log dm_mod fuse overlay squashfs loop CPU: 12 PID: 274 Comm: systemd-udevd Not tainted 5.13.0-rc7 #1 NIP: c00000000818e9a8 LR: c0000000089846e8 CTR: 0000000000007ee8 REGS: c000000037d12ea0 TRAP: 0300 Not tainted (5.13.0-rc7) MSR: 800000000280b033 &lt;SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE&gt; CR: 28228228 XER: 20040001 CFAR: c0000000089846e4 DAR: 000000000000010c DSISR: 40000000 IRQMASK: 0 GPR00: c0000000089846e8 c000000037d13140 c000000009cc1100 fffffffffffffffc GPR04: 0000000000000001 0000000000000000 0000000000000000 c000000037dc0000 GPR08: 0000000000000000 c000000037dc0000 0000000000000001 00000000fffff7ff GPR12: 0000000000008000 c00000000a049000 c000000037d13d00 000000011134d5a0 GPR16: 0000000000001740 c0080000190d0000 c0080000190d1740 c000000009129288 GPR20: c000000037d13bc0 0000000000000001 c000000037d13bc0 c0080000190b7898 GPR24: c0080000190b7708 0000000000000000 c000000033bb2c48 0000000000000000 GPR28: c000000046b28280 0000000000000000 000000000000010c fffffffffffffffc NIP [c00000000818e9a8] kthread_stop+0x38/0x230 LR [c0000000089846e8] scsi_host_dev_release+0x98/0x160 Call Trace: [c000000033bb2c48] 0xc000000033bb2c48 (unreliable) [c0000000089846e8] scsi_host_dev_release+0x98/0x160 [c00000000891e960] device_release+0x60/0x100 [c0000000087e55c4] kobject_release+0x84/0x210 [c00000000891ec78] put_device+0x28/0x40 [c000000008984ea4] scsi_host_alloc+0x314/0x430 [c0080000190b38bc] ibmvscsi_probe+0x54/0xad0 [ibmvscsi] [c000000008110104] vio_bus_probe+0xa4/0x4b0 [c00000000892a860] really_probe+0x140/0x680 [c00000000892aefc] driver_probe_device+0x15c/0x200 [c00000000892b63c] device_driver_attach+0xcc/0xe0 [c00000000892b740] __driver_attach+0xf0/0x200 [c000000008926f28] bus_for_each_dev+0xa8/0x130 [c000000008929ce4] driver_attach+0x34/0x50 [c000000008928fc0] bus_add_driver+0x1b0/0x300 [c00000000892c798] driver_register+0x98/0x1a0 [c00000000810eb60] __vio_register_driver+0x80/0xe0 [c0080000190b4a30] ibmvscsi_module_init+0x9c/0xdc [ibmvscsi] [c0000000080121d0] do_one_initcall+0x60/0x2d0 [c000000008261abc] do_init_module+0x7c/0x320 [c000000008265700] load_module+0x2350/0x25b0 [c000000008265cb4] __do_sys_finit_module+0xd4/0x160 [c000000008031110] system_call_exception+0x150/0x2d0 [c00000000800d35c] system_call_common+0xec/0x278 Fix this be nulling shost->ehandler when the kthread fails to spawn.

In the Linux kernel, the following vulnerability has been resolved: HID: bigbenff: prevent null pointer dereference When emulating the device through uhid, there is a chance we don't have output reports and so report_field is null.

In the Linux kernel, the following vulnerability has been resolved: serial: liteuart: Fix NULL pointer dereference in ->remove() drvdata has to be set in _probe() - otherwise platform_get_drvdata() causes null pointer dereference BUG in _remove().

In the Linux kernel, the following vulnerability has been resolved: usb: chipidea: ci_hdrc_imx: Also search for 'phys' phandle When passing 'phys' in the devicetree to describe the USB PHY phandle (which is the recommended way according to Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt) the following NULL pointer dereference is observed on i.MX7 and i.MX8MM: [ 1.489344] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000098 [ 1.498170] Mem abort info: [ 1.500966] ESR = 0x96000044 [ 1.504030] EC = 0x25: DABT (current EL), IL = 32 bits [ 1.509356] SET = 0, FnV = 0 [ 1.512416] EA = 0, S1PTW = 0 [ 1.515569] FSC = 0x04: level 0 translation fault [ 1.520458] Data abort info: [ 1.523349] ISV = 0, ISS = 0x00000044 [ 1.527196] CM = 0, WnR = 1 [ 1.530176] [0000000000000098] user address but active_mm is swapper [ 1.536544] Internal error: Oops: 96000044 [#1] PREEMPT SMP [ 1.542125] Modules linked in: [ 1.545190] CPU: 3 PID: 7 Comm: kworker/u8:0 Not tainted 5.14.0-dirty #3 [ 1.551901] Hardware name: Kontron i.MX8MM N801X S (DT) [ 1.557133] Workqueue: events_unbound deferred_probe_work_func [ 1.562984] pstate: 80000005 (Nzcv daif -PAN -UAO -TCO BTYPE=--) [ 1.568998] pc : imx7d_charger_detection+0x3f0/0x510 [ 1.573973] lr : imx7d_charger_detection+0x22c/0x510 This happens because the charger functions check for the phy presence inside the imx_usbmisc_data structure (data->usb_phy), but the chipidea core populates the usb_phy passed via 'phys' inside 'struct ci_hdrc' (ci->usb_phy) instead. This causes the NULL pointer dereference inside imx7d_charger_detection(). Fix it by also searching for 'phys' in case 'fsl,usbphy' is not found. Tested on a imx7s-warp board.

In the Linux kernel, the following vulnerability has been resolved: ALSA: usx2y: Don't call free_pages_exact() with NULL address Unlike some other functions, we can't pass NULL pointer to free_pages_exact(). Add a proper NULL check for avoiding possible Oops.

In the Linux kernel, the following vulnerability has been resolved: net: nexthop: fix null pointer dereference when IPv6 is not enabled When we try to add an IPv6 nexthop and IPv6 is not enabled (!CONFIG_IPV6) we'll hit a NULL pointer dereference[1] in the error path of nh_create_ipv6() due to calling ipv6_stub->fib6_nh_release. The bug has been present since the beginning of IPv6 nexthop gateway support. Commit 1aefd3de7bc6 ("ipv6: Add fib6_nh_init and release to stubs") tells us that only fib6_nh_init has a dummy stub because fib6_nh_release should not be called if fib6_nh_init returns an error, but the commit below added a call to ipv6_stub->fib6_nh_release in its error path. To fix it return the dummy stub's -EAFNOSUPPORT error directly without calling ipv6_stub->fib6_nh_release in nh_create_ipv6()'s error path. [1] Output is a bit truncated, but it clearly shows the error. BUG: kernel NULL pointer dereference, address: 000000000000000000 #PF: supervisor instruction fetch in kernel modede #PF: error_code(0x0010) - not-present pagege PGD 0 P4D 0 Oops: 0010 [#1] PREEMPT SMP NOPTI CPU: 4 PID: 638 Comm: ip Kdump: loaded Not tainted 5.16.0-rc1+ #446 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-4.fc34 04/01/2014 RIP: 0010:0x0 Code: Unable to access opcode bytes at RIP 0xffffffffffffffd6. RSP: 0018:ffff888109f5b8f0 EFLAGS: 00010286^Ac RAX: 0000000000000000 RBX: ffff888109f5ba28 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff8881008a2860 RBP: ffff888109f5b9d8 R08: 0000000000000000 R09: 0000000000000000 R10: ffff888109f5b978 R11: ffff888109f5b948 R12: 00000000ffffff9f R13: ffff8881008a2a80 R14: ffff8881008a2860 R15: ffff8881008a2840 FS: 00007f98de70f100(0000) GS:ffff88822bf00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffffffffffd6 CR3: 0000000100efc000 CR4: 00000000000006e0 Call Trace: <TASK> nh_create_ipv6+0xed/0x10c rtm_new_nexthop+0x6d7/0x13f3 ? check_preemption_disabled+0x3d/0xf2 ? lock_is_held_type+0xbe/0xfd rtnetlink_rcv_msg+0x23f/0x26a ? check_preemption_disabled+0x3d/0xf2 ? rtnl_calcit.isra.0+0x147/0x147 netlink_rcv_skb+0x61/0xb2 netlink_unicast+0x100/0x187 netlink_sendmsg+0x37f/0x3a0 ? netlink_unicast+0x187/0x187 sock_sendmsg_nosec+0x67/0x9b ____sys_sendmsg+0x19d/0x1f9 ? copy_msghdr_from_user+0x4c/0x5e ? rcu_read_lock_any_held+0x2a/0x78 ___sys_sendmsg+0x6c/0x8c ? asm_sysvec_apic_timer_interrupt+0x12/0x20 ? lockdep_hardirqs_on+0xd9/0x102 ? sockfd_lookup_light+0x69/0x99 __sys_sendmsg+0x50/0x6e do_syscall_64+0xcb/0xf2 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f98dea28914 Code: 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b5 0f 1f 80 00 00 00 00 48 8d 05 e9 5d 0c 00 8b 00 85 c0 75 13 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 54 c3 0f 1f 00 41 54 41 89 d4 55 48 89 f5 53 RSP: 002b:00007fff859f5e68 EFLAGS: 00000246 ORIG_RAX: 000000000000002e2e RAX: ffffffffffffffda RBX: 00000000619cb810 RCX: 00007f98dea28914 RDX: 0000000000000000 RSI: 00007fff859f5ed0 RDI: 0000000000000003 RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000008 R10: fffffffffffffce6 R11: 0000000000000246 R12: 0000000000000001 R13: 000055c0097ae520 R14: 000055c0097957fd R15: 00007fff859f63a0 </TASK> Modules linked in: bridge stp llc bonding virtio_net

In the Linux kernel, the following vulnerability has been resolved: soc: qcom: rpmpd: Check for null return of devm_kcalloc Because of the possible failure of the allocation, data->domains might be NULL pointer and will cause the dereference of the NULL pointer later. Therefore, it might be better to check it and directly return -ENOMEM without releasing data manually if fails, because the comment of the devm_kmalloc() says "Memory allocated with this function is automatically freed on driver detach.".

In the Linux kernel, the following vulnerability has been resolved: ACPI: fix NULL pointer dereference Commit 71f642833284 ("ACPI: utils: Fix reference counting in for_each_acpi_dev_match()") started doing "acpi_dev_put()" on a pointer that was possibly NULL. That fails miserably, because that helper inline function is not set up to handle that case. Just make acpi_dev_put() silently accept a NULL pointer, rather than calling down to put_device() with an invalid offset off that NULL pointer.

In the Linux kernel, the following vulnerability has been resolved: video: fbdev: smscufx: Fix null-ptr-deref in ufx_usb_probe() I got a null-ptr-deref report: BUG: kernel NULL pointer dereference, address: 0000000000000000 ... RIP: 0010:fb_destroy_modelist+0x38/0x100 ... Call Trace: ufx_usb_probe.cold+0x2b5/0xac1 [smscufx] usb_probe_interface+0x1aa/0x3c0 [usbcore] really_probe+0x167/0x460 ... ret_from_fork+0x1f/0x30 If fb_alloc_cmap() fails in ufx_usb_probe(), fb_destroy_modelist() will be called to destroy modelist in the error handling path. But modelist has not been initialized yet, so it will result in null-ptr-deref. Initialize modelist before calling fb_alloc_cmap() to fix this bug.

In the Linux kernel, the following vulnerability has been resolved: usb: misc: brcmstb-usb-pinmap: check return value after calling platform_get_resource() It will cause null-ptr-deref if platform_get_resource() returns NULL, we need check the return value.

In the Linux kernel, the following vulnerability has been resolved: cifs: prevent NULL deref in cifs_compose_mount_options() The optional @ref parameter might contain an NULL node_name, so prevent dereferencing it in cifs_compose_mount_options(). Addresses-Coverity: 1476408 ("Explicit null dereferenced")

In the Linux kernel, the following vulnerability has been resolved: nfsd: fix NULL dereference in nfs3svc_encode_getaclres In error cases the dentry may be NULL. Before 20798dfe249a, the encoder also checked dentry and d_really_is_positive(dentry), but that looks like overkill to me--zero status should be enough to guarantee a positive dentry. This isn't the first time we've seen an error-case NULL dereference hidden in the initialization of a local variable in an xdr encoder. But I went back through the other recent rewrites and didn't spot any similar bugs.

In the Linux kernel, the following vulnerability has been resolved: NFS: Fix a potential NULL dereference in nfs_get_client() None of the callers are expecting NULL returns from nfs_get_client() so this code will lead to an Oops. It's better to return an error pointer. I expect that this is dead code so hopefully no one is affected.

In the Linux kernel, the following vulnerability has been resolved: ALSA: gus: fix null pointer dereference on pointer block The pointer block return from snd_gf1_dma_next_block could be null, so there is a potential null pointer dereference issue. Fix this by adding a null check before dereference.

In the Linux kernel, the following vulnerability has been resolved: platform/x86: ideapad-laptop: fix a NULL pointer dereference The third parameter of dytc_cql_command should not be NULL since it will be dereferenced immediately.

A null pointer dereference issue was found in can protocol in net/can/af_can.c in the Linux before Linux. ml_priv may not be initialized in the receive path of CAN frames. A local user could use this flaw to crash the system or potentially cause a denial of service.