In the Linux kernel, the following vulnerability has been resolved: media: streamzap: fix race between device disconnection and urb callback Syzkaller has reported a general protection fault at function ir_raw_event_store_with_filter(). This crash is caused by a NULL pointer dereference of dev->raw pointer, even though it is checked for NULL in the same function, which means there is a race condition. It occurs due to the incorrect order of actions in the streamzap_disconnect() function: rc_unregister_device() is called before usb_kill_urb(). The dev->raw pointer is freed and set to NULL in rc_unregister_device(), and only after that usb_kill_urb() waits for in-progress requests to finish. If rc_unregister_device() is called while streamzap_callback() handler is not finished, this can lead to accessing freed resources. Thus rc_unregister_device() should be called after usb_kill_urb(). Found by Linux Verification Center (linuxtesting.org) with Syzkaller.

In the Linux kernel, the following vulnerability has been resolved: nvme-pci: fix race condition between reset and nvme_dev_disable() nvme_dev_disable() modifies the dev->online_queues field, therefore nvme_pci_update_nr_queues() should avoid racing against it, otherwise we could end up passing invalid values to blk_mq_update_nr_hw_queues(). WARNING: CPU: 39 PID: 61303 at drivers/pci/msi/api.c:347 pci_irq_get_affinity+0x187/0x210 Workqueue: nvme-reset-wq nvme_reset_work [nvme] RIP: 0010:pci_irq_get_affinity+0x187/0x210 Call Trace: <TASK> ? blk_mq_pci_map_queues+0x87/0x3c0 ? pci_irq_get_affinity+0x187/0x210 blk_mq_pci_map_queues+0x87/0x3c0 nvme_pci_map_queues+0x189/0x460 [nvme] blk_mq_update_nr_hw_queues+0x2a/0x40 nvme_reset_work+0x1be/0x2a0 [nvme] Fix the bug by locking the shutdown_lock mutex before using dev->online_queues. Give up if nvme_dev_disable() is running or if it has been executed already.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to check atomic_file in f2fs ioctl interfaces Some f2fs ioctl interfaces like f2fs_ioc_set_pin_file(), f2fs_move_file_range(), and f2fs_defragment_range() missed to check atomic_write status, which may cause potential race issue, fix it.

In the Linux kernel, the following vulnerability has been resolved: tracing/timerlat: Fix a race during cpuhp processing There is another found exception that the "timerlat/1" thread was scheduled on CPU0, and lead to timer corruption finally: ``` ODEBUG: init active (active state 0) object: ffff888237c2e108 object type: hrtimer hint: timerlat_irq+0x0/0x220 WARNING: CPU: 0 PID: 426 at lib/debugobjects.c:518 debug_print_object+0x7d/0xb0 Modules linked in: CPU: 0 UID: 0 PID: 426 Comm: timerlat/1 Not tainted 6.11.0-rc7+ #45 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014 RIP: 0010:debug_print_object+0x7d/0xb0 ... Call Trace: <TASK> ? __warn+0x7c/0x110 ? debug_print_object+0x7d/0xb0 ? report_bug+0xf1/0x1d0 ? prb_read_valid+0x17/0x20 ? handle_bug+0x3f/0x70 ? exc_invalid_op+0x13/0x60 ? asm_exc_invalid_op+0x16/0x20 ? debug_print_object+0x7d/0xb0 ? debug_print_object+0x7d/0xb0 ? __pfx_timerlat_irq+0x10/0x10 __debug_object_init+0x110/0x150 hrtimer_init+0x1d/0x60 timerlat_main+0xab/0x2d0 ? __pfx_timerlat_main+0x10/0x10 kthread+0xb7/0xe0 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2d/0x40 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> ``` After tracing the scheduling event, it was discovered that the migration of the "timerlat/1" thread was performed during thread creation. Further analysis confirmed that it is because the CPU online processing for osnoise is implemented through workers, which is asynchronous with the offline processing. When the worker was scheduled to create a thread, the CPU may has already been removed from the cpu_online_mask during the offline process, resulting in the inability to select the right CPU: T1 | T2 [CPUHP_ONLINE] | cpu_device_down() osnoise_hotplug_workfn() | | cpus_write_lock() | takedown_cpu(1) | cpus_write_unlock() [CPUHP_OFFLINE] | cpus_read_lock() | start_kthread(1) | cpus_read_unlock() | To fix this, skip online processing if the CPU is already offline.

In the Linux kernel, the following vulnerability has been resolved: mm/gup: fix memfd_pin_folios alloc race panic If memfd_pin_folios tries to create a hugetlb page, but someone else already did, then folio gets the value -EEXIST here: folio = memfd_alloc_folio(memfd, start_idx); if (IS_ERR(folio)) { ret = PTR_ERR(folio); if (ret != -EEXIST) goto err; then on the next trip through the "while start_idx" loop we panic here: if (folio) { folio_put(folio); To fix, set the folio to NULL on error.

In the Linux kernel, the following vulnerability has been resolved: lib/generic-radix-tree.c: Fix rare race in __genradix_ptr_alloc() If we need to increase the tree depth, allocate a new node, and then race with another thread that increased the tree depth before us, we'll still have a preallocated node that might be used later. If we then use that node for a new non-root node, it'll still have a pointer to the old root instead of being zeroed - fix this by zeroing it in the cmpxchg failure path.

In the Linux kernel, the following vulnerability has been resolved: ALSA: line6: Fix racy access to midibuf There can be concurrent accesses to line6 midibuf from both the URB completion callback and the rawmidi API access. This could be a cause of KMSAN warning triggered by syzkaller below (so put as reported-by here). This patch protects the midibuf call of the former code path with a spinlock for avoiding the possible races.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Always drain health in shutdown callback There is no point in recovery during device shutdown. if health work started need to wait for it to avoid races and NULL pointer access. Hence, drain health WQ on shutdown callback.

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: f_fs: Remove WARN_ON in functionfs_bind This commit addresses an issue related to below kernel panic where panic_on_warn is enabled. It is caused by the unnecessary use of WARN_ON in functionsfs_bind, which easily leads to the following scenarios. 1.adb_write in adbd 2. UDC write via configfs ================= ===================== ->usb_ffs_open_thread() ->UDC write ->open_functionfs() ->configfs_write_iter() ->adb_open() ->gadget_dev_desc_UDC_store() ->adb_write() ->usb_gadget_register_driver_owner ->driver_register() ->StartMonitor() ->bus_add_driver() ->adb_read() ->gadget_bind_driver() <times-out without BIND event> ->configfs_composite_bind() ->usb_add_function() ->open_functionfs() ->ffs_func_bind() ->adb_open() ->functionfs_bind() <ffs->state !=FFS_ACTIVE> The adb_open, adb_read, and adb_write operations are invoked from the daemon, but trying to bind the function is a process that is invoked by UDC write through configfs, which opens up the possibility of a race condition between the two paths. In this race scenario, the kernel panic occurs due to the WARN_ON from functionfs_bind when panic_on_warn is enabled. This commit fixes the kernel panic by removing the unnecessary WARN_ON. Kernel panic - not syncing: kernel: panic_on_warn set ... [ 14.542395] Call trace: [ 14.542464] ffs_func_bind+0x1c8/0x14a8 [ 14.542468] usb_add_function+0xcc/0x1f0 [ 14.542473] configfs_composite_bind+0x468/0x588 [ 14.542478] gadget_bind_driver+0x108/0x27c [ 14.542483] really_probe+0x190/0x374 [ 14.542488] __driver_probe_device+0xa0/0x12c [ 14.542492] driver_probe_device+0x3c/0x220 [ 14.542498] __driver_attach+0x11c/0x1fc [ 14.542502] bus_for_each_dev+0x104/0x160 [ 14.542506] driver_attach+0x24/0x34 [ 14.542510] bus_add_driver+0x154/0x270 [ 14.542514] driver_register+0x68/0x104 [ 14.542518] usb_gadget_register_driver_owner+0x48/0xf4 [ 14.542523] gadget_dev_desc_UDC_store+0xf8/0x144 [ 14.542526] configfs_write_iter+0xf0/0x138

A Race Condition in the 'show chassis pic' command in Juniper Networks Junos OS Evolved may allow an attacker to crash the port interface concentrator daemon (picd) process on the FPC, if the command is executed coincident with other system events outside the attacker's control, leading to a Denial of Service (DoS) condition. Continued execution of the CLI command, under precise conditions, could create a sustained Denial of Service (DoS) condition. This issue affects all Juniper Networks Junos OS Evolved versions prior to 20.1R2-EVO on PTX10003 and PTX10008 platforms. Junos OS is not affected by this vulnerability.

In the Linux kernel, the following vulnerability has been resolved: firmware: arm_scmi: Check mailbox/SMT channel for consistency On reception of a completion interrupt the shared memory area is accessed to retrieve the message header at first and then, if the message sequence number identifies a transaction which is still pending, the related payload is fetched too. When an SCMI command times out the channel ownership remains with the platform until eventually a late reply is received and, as a consequence, any further transmission attempt remains pending, waiting for the channel to be relinquished by the platform. Once that late reply is received the channel ownership is given back to the agent and any pending request is then allowed to proceed and overwrite the SMT area of the just delivered late reply; then the wait for the reply to the new request starts. It has been observed that the spurious IRQ related to the late reply can be wrongly associated with the freshly enqueued request: when that happens the SCMI stack in-flight lookup procedure is fooled by the fact that the message header now present in the SMT area is related to the new pending transaction, even though the real reply has still to arrive. This race-condition on the A2P channel can be detected by looking at the channel status bits: a genuine reply from the platform will have set the channel free bit before triggering the completion IRQ. Add a consistency check to validate such condition in the A2P ISR.

In the Linux kernel, the following vulnerability has been resolved: perf/core: Fix data race between perf_event_set_output() and perf_mmap_close() Yang Jihing reported a race between perf_event_set_output() and perf_mmap_close(): CPU1 CPU2 perf_mmap_close(e2) if (atomic_dec_and_test(&e2->rb->mmap_count)) // 1 - > 0 detach_rest = true ioctl(e1, IOC_SET_OUTPUT, e2) perf_event_set_output(e1, e2) ... list_for_each_entry_rcu(e, &e2->rb->event_list, rb_entry) ring_buffer_attach(e, NULL); // e1 isn't yet added and // therefore not detached ring_buffer_attach(e1, e2->rb) list_add_rcu(&e1->rb_entry, &e2->rb->event_list) After this; e1 is attached to an unmapped rb and a subsequent perf_mmap() will loop forever more: again: mutex_lock(&e->mmap_mutex); if (event->rb) { ... if (!atomic_inc_not_zero(&e->rb->mmap_count)) { ... mutex_unlock(&e->mmap_mutex); goto again; } } The loop in perf_mmap_close() holds e2->mmap_mutex, while the attach in perf_event_set_output() holds e1->mmap_mutex. As such there is no serialization to avoid this race. Change perf_event_set_output() to take both e1->mmap_mutex and e2->mmap_mutex to alleviate that problem. Additionally, have the loop in perf_mmap() detach the rb directly, this avoids having to wait for the concurrent perf_mmap_close() to get around to doing it to make progress.

In the Linux kernel, the following vulnerability has been resolved: drm/v3d: Assign job pointer to NULL before signaling the fence In commit e4b5ccd392b9 ("drm/v3d: Ensure job pointer is set to NULL after job completion"), we introduced a change to assign the job pointer to NULL after completing a job, indicating job completion. However, this approach created a race condition between the DRM scheduler workqueue and the IRQ execution thread. As soon as the fence is signaled in the IRQ execution thread, a new job starts to be executed. This results in a race condition where the IRQ execution thread sets the job pointer to NULL simultaneously as the `run_job()` function assigns a new job to the pointer. This race condition can lead to a NULL pointer dereference if the IRQ execution thread sets the job pointer to NULL after `run_job()` assigns it to the new job. When the new job completes and the GPU emits an interrupt, `v3d_irq()` is triggered, potentially causing a crash. [ 466.310099] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000c0 [ 466.318928] Mem abort info: [ 466.321723] ESR = 0x0000000096000005 [ 466.325479] EC = 0x25: DABT (current EL), IL = 32 bits [ 466.330807] SET = 0, FnV = 0 [ 466.333864] EA = 0, S1PTW = 0 [ 466.337010] FSC = 0x05: level 1 translation fault [ 466.341900] Data abort info: [ 466.344783] ISV = 0, ISS = 0x00000005, ISS2 = 0x00000000 [ 466.350285] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 466.355350] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 466.360677] user pgtable: 4k pages, 39-bit VAs, pgdp=0000000089772000 [ 466.367140] [00000000000000c0] pgd=0000000000000000, p4d=0000000000000000, pud=0000000000000000 [ 466.375875] Internal error: Oops: 0000000096000005 [#1] PREEMPT SMP [ 466.382163] Modules linked in: rfcomm snd_seq_dummy snd_hrtimer snd_seq snd_seq_device algif_hash algif_skcipher af_alg bnep binfmt_misc vc4 snd_soc_hdmi_codec drm_display_helper cec brcmfmac_wcc spidev rpivid_hevc(C) drm_client_lib brcmfmac hci_uart drm_dma_helper pisp_be btbcm brcmutil snd_soc_core aes_ce_blk v4l2_mem2mem bluetooth aes_ce_cipher snd_compress videobuf2_dma_contig ghash_ce cfg80211 gf128mul snd_pcm_dmaengine videobuf2_memops ecdh_generic sha2_ce ecc videobuf2_v4l2 snd_pcm v3d sha256_arm64 rfkill videodev snd_timer sha1_ce libaes gpu_sched snd videobuf2_common sha1_generic drm_shmem_helper mc rp1_pio drm_kms_helper raspberrypi_hwmon spi_bcm2835 gpio_keys i2c_brcmstb rp1 raspberrypi_gpiomem rp1_mailbox rp1_adc nvmem_rmem uio_pdrv_genirq uio i2c_dev drm ledtrig_pattern drm_panel_orientation_quirks backlight fuse dm_mod ip_tables x_tables ipv6 [ 466.458429] CPU: 0 UID: 1000 PID: 2008 Comm: chromium Tainted: G C 6.13.0-v8+ #18 [ 466.467336] Tainted: [C]=CRAP [ 466.470306] Hardware name: Raspberry Pi 5 Model B Rev 1.0 (DT) [ 466.476157] pstate: 404000c9 (nZcv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 466.483143] pc : v3d_irq+0x118/0x2e0 [v3d] [ 466.487258] lr : __handle_irq_event_percpu+0x60/0x228 [ 466.492327] sp : ffffffc080003ea0 [ 466.495646] x29: ffffffc080003ea0 x28: ffffff80c0c94200 x27: 0000000000000000 [ 466.502807] x26: ffffffd08dd81d7b x25: ffffff80c0c94200 x24: ffffff8003bdc200 [ 466.509969] x23: 0000000000000001 x22: 00000000000000a7 x21: 0000000000000000 [ 466.517130] x20: ffffff8041bb0000 x19: 0000000000000001 x18: 0000000000000000 [ 466.524291] x17: ffffffafadfb0000 x16: ffffffc080000000 x15: 0000000000000000 [ 466.531452] x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000 [ 466.538613] x11: 0000000000000000 x10: 0000000000000000 x9 : ffffffd08c527eb0 [ 466.545777] x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000000000 [ 466.552941] x5 : ffffffd08c4100d0 x4 : ffffffafadfb0000 x3 : ffffffc080003f70 [ 466.560102] x2 : ffffffc0829e8058 x1 : 0000000000000001 x0 : 0000000000000000 [ 466.567263] Call trace: [ 466.569711] v3d_irq+0x118/0x2e0 [v3d] (P) [ 466. ---truncated---