Buffer overflow in Active Management Technology (AMT) in Intel Manageability Engine Firmware 8.x/9.x/10.x/11.0/11.5/11.6/11.7/11.10/11.20 allows attacker with remote Admin access to the system to execute arbitrary code with AMT execution privilege.

The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities.

A buffer copy without checking size of input vulnerability has been reported to affect several QNAP operating system versions. If exploited, the vulnerability could allow authenticated users to execute code via a network. We have already fixed the vulnerability in the following versions: QTS 5.1.6.2722 build 20240402 and later QuTS hero h5.1.6.2734 build 20240414 and later

A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device.  The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability.

The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities.

The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities.

The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities.

A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device.  The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability.

A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device.  The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability.

Multiple vulnerabilities in the web-based management interface of Cisco Small Business RV110W, RV130, RV130W, and RV215W Routers could allow an authenticated, remote attacker to execute arbitrary code or cause an affected device to restart unexpectedly. The vulnerabilities are due to improper validation of user-supplied input in the web-based management interface. An attacker could exploit these vulnerabilities by sending crafted HTTP requests to an affected device. A successful exploit could allow the attacker to execute arbitrary code as the root user on the underlying operating system or cause the device to reload, resulting in a denial of service (DoS) condition. To exploit these vulnerabilities, an attacker would need to have valid administrator credentials on the affected device. Cisco has not released software updates that address these vulnerabilities.

Multiple vulnerabilities in the web-based management interface of Cisco Small Business RV110W, RV130, RV130W, and RV215W Routers could allow an authenticated, remote attacker to execute arbitrary code or cause an affected device to restart unexpectedly. The vulnerabilities are due to improper validation of user-supplied input in the web-based management interface. An attacker could exploit these vulnerabilities by sending crafted HTTP requests to an affected device. A successful exploit could allow the attacker to execute arbitrary code as the root user on the underlying operating system or cause the device to reload, resulting in a denial of service (DoS) condition. To exploit these vulnerabilities, an attacker would need to have valid administrator credentials on the affected device. Cisco has not released software updates that address these vulnerabilities.

Apache PLC4X - PLC4C (Only the C language implementation was effected) was vulnerable to an unsigned integer underflow flaw inside the tcp transport. Users should update to 0.9.1, which addresses this issue. However, in order to exploit this vulnerability, a user would have to actively connect to a mallicious device which could send a response with invalid content. Currently we consider the probability of this being exploited as quite minimal, however this could change in the future, especially with the industrial networks growing more and more together.

VMware ESXi (6.0 before ESXi600-201711101-SG, 5.5 ESXi550-201709101-SG), Workstation (12.x before 12.5.8), and Fusion (8.x before 8.5.9) contain a vulnerability that could allow an authenticated VNC session to cause a stack overflow via a specific set of VNC packets. Successful exploitation of this issue could result in remote code execution in a virtual machine via the authenticated VNC session. Note: In order for exploitation to be possible in ESXi, VNC must be manually enabled in a virtual machine's .vmx configuration file. In addition, ESXi must be configured to allow VNC traffic through the built-in firewall.

Multiple vulnerabilities in the web-based management interface of Cisco Small Business RV110W, RV130, RV130W, and RV215W Routers could allow an authenticated, remote attacker to execute arbitrary code or cause an affected device to restart unexpectedly. The vulnerabilities are due to improper validation of user-supplied input in the web-based management interface. An attacker could exploit these vulnerabilities by sending crafted HTTP requests to an affected device. A successful exploit could allow the attacker to execute arbitrary code as the root user on the underlying operating system or cause the device to reload, resulting in a denial of service (DoS) condition. To exploit these vulnerabilities, an attacker would need to have valid administrator credentials on the affected device. Cisco has not released software updates that address these vulnerabilities.

A vulnerability has been found in Tenda AC20 up to 16.03.08.12. The impacted element is the function sscanf of the file /goform/PowerSaveSet. The manipulation of the argument powerSavingEn/time/powerSaveDelay/ledCloseType leads to buffer overflow. The attack can be initiated remotely. The exploit has been disclosed to the public and may be used.

A security vulnerability has been detected in LLM-Claw 0.1.0/0.1.1/0.1.1a/0.1.1a-p1. The affected element is the function agent_deploy_init of the file /agents/deploy/initiate.c of the component Agent Deployment. Such manipulation leads to buffer overflow. It is possible to launch the attack remotely. A patch should be applied to remediate this issue.

In Advantech WebAccess, Versions 8.4.2 and prior. A stack-based buffer overflow vulnerability caused by a lack of proper validation of the length of user-supplied data may allow remote code execution.

Multiple vulnerabilities in the web-based management interface of Cisco Small Business RV110W, RV130, RV130W, and RV215W Routers could allow an authenticated, remote attacker to execute arbitrary code or cause an affected device to restart unexpectedly. The vulnerabilities are due to improper validation of user-supplied input in the web-based management interface. An attacker could exploit these vulnerabilities by sending crafted HTTP requests to an affected device. A successful exploit could allow the attacker to execute arbitrary code as the root user on the underlying operating system or cause the device to reload, resulting in a denial of service (DoS) condition. To exploit these vulnerabilities, an attacker would need to have valid administrator credentials on the affected device. Cisco has not released software updates that address these vulnerabilities.

A flaw has been found in Tenda FH1201 and FH1206 1.2.0.14(408)/1.2.0.8(8155). This impacts the function strcat of the file /goform/webtypelibrary of the component HTTP Request Handler. This manipulation of the argument webSiteId causes stack-based buffer overflow. The attack is possible to be carried out remotely. The exploit has been published and may be used.

Multiple vulnerabilities in the web-based management interface of Cisco Small Business RV110W, RV130, RV130W, and RV215W Routers could allow an authenticated, remote attacker to execute arbitrary code or cause an affected device to restart unexpectedly. The vulnerabilities are due to improper validation of user-supplied input in the web-based management interface. An attacker could exploit these vulnerabilities by sending crafted HTTP requests to an affected device. A successful exploit could allow the attacker to execute arbitrary code as the root user on the underlying operating system or cause the device to reload, resulting in a denial of service (DoS) condition. To exploit these vulnerabilities, an attacker would need to have valid administrator credentials on the affected device. Cisco has not released software updates that address these vulnerabilities.

A vulnerability has been found in UTT 进取 520W 1.7.7-180627. This issue affects the function strcpy of the file /goform/ConfigAdvideo. The manipulation of the argument timestart leads to buffer overflow. The attack is possible to be carried out remotely. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

Vyper is a Pythonic Smart Contract Language for the EVM. In affected versions when performing a function call inside a literal struct, there is a memory corruption issue that occurs because of an incorrect pointer to the the top of the stack. This issue has been resolved in version 0.3.0.

A security flaw has been discovered in D-Link DWR-M920 up to 1.1.50. Impacted is the function sub_42261C of the file /boafrm/formFilter. The manipulation of the argument ip6addr results in stack-based buffer overflow. The attack may be launched remotely. The exploit has been released to the public and may be exploited.

A vulnerability was identified in Tenda M3 1.0.0.13(4903). This vulnerability affects the function formSetAdPushInfo of the file /goform/setAdPushInfo. The manipulation of the argument mac/terminal leads to stack-based buffer overflow. The attack is possible to be carried out remotely. The exploit is publicly available and might be used.

A security flaw has been discovered in Tenda M3 1.0.0.13(4903). This issue affects the function formSetAdInfoDetails of the file /goform/setAdInfoDetail. The manipulation of the argument adName/smsPassword/smsAccount/weixinAccount/weixinName/smsSignature/adRedirectUrl/adCopyRight/smsContent/adItemUID results in heap-based buffer overflow. The attack may be performed from remote. The exploit has been released to the public and may be used for attacks.

A vulnerability classified as critical was found in D-Link DAP-1320 1.00. Affected by this vulnerability is the function set_ws_action of the file /dws/api/. The manipulation leads to heap-based buffer overflow. The attack can be launched remotely. The exploit has been disclosed to the public and may be used. This vulnerability only affects products that are no longer supported by the maintainer.

A vulnerability was identified in D-Link DWR-M920 up to 1.1.50. This issue affects the function sub_464794 of the file /boafrm/formDefRoute. The manipulation of the argument submit-url leads to buffer overflow. The attack may be initiated remotely. The exploit is publicly available and might be used.

A vulnerability was determined in Tenda AC10U 15.03.06.48/15.03.06.49. This affects the function formSetPPTPUserList of the file /goform/setPptpUserList of the component HTTP POST Request Handler. This manipulation of the argument list causes buffer overflow. It is possible to initiate the attack remotely. The exploit has been publicly disclosed and may be utilized.

Multiple vulnerabilities in the web-based management interface of Cisco Small Business RV110W, RV130, RV130W, and RV215W Routers could allow an authenticated, remote attacker to execute arbitrary code or cause an affected device to restart unexpectedly. The vulnerabilities are due to improper validation of user-supplied input in the web-based management interface. An attacker could exploit these vulnerabilities by sending crafted HTTP requests to an affected device. A successful exploit could allow the attacker to execute arbitrary code as the root user on the underlying operating system or cause the device to reload, resulting in a denial of service (DoS) condition. To exploit these vulnerabilities, an attacker would need to have valid administrator credentials on the affected device. Cisco has not released software updates that address these vulnerabilities.

Multiple vulnerabilities in the web-based management interface of Cisco Small Business RV016, RV042, RV042G, RV082, RV320, and RV325 Routers could allow an authenticated, remote attacker to execute arbitrary code or cause an affected device to restart unexpectedly. These vulnerabilities are due to improper validation of user-supplied input in the web-based management interface. An attacker could exploit these vulnerabilities by sending crafted HTTP requests to an affected device. A successful exploit could allow the attacker to execute arbitrary code as the root user on the underlying operating system or cause the device to reload, resulting in a denial of service (DoS) condition. To exploit these vulnerabilities, an attacker would need to have valid administrator credentials on the affected device.

Multiple vulnerabilities in the web-based management interface of Cisco Small Business RV110W, RV130, RV130W, and RV215W Routers could allow an authenticated, remote attacker to execute arbitrary code or cause an affected device to restart unexpectedly. The vulnerabilities are due to improper validation of user-supplied input in the web-based management interface. An attacker could exploit these vulnerabilities by sending crafted HTTP requests to an affected device. A successful exploit could allow the attacker to execute arbitrary code as the root user on the underlying operating system or cause the device to reload, resulting in a denial of service (DoS) condition. To exploit these vulnerabilities, an attacker would need to have valid administrator credentials on the affected device. Cisco has not released software updates that address these vulnerabilities.

A vulnerability was determined in UTT 进取 512W up to 1.7.7-171114. This issue affects the function strcpy of the file /goform/formPictureUrl. This manipulation of the argument importpictureurl causes buffer overflow. It is possible to initiate the attack remotely. The exploit has been publicly disclosed and may be utilized.

A weakness has been identified in Tenda AC10U 15.03.06.48/15.03.06.49. Affected by this vulnerability is the function fromadvsetlanip of the file /goform/AdvSetLanip of the component POST Request Parameter Handler. Executing a manipulation of the argument lanMask can lead to buffer overflow. The attack can be launched remotely. The exploit has been made available to the public and could be used for attacks.

A vulnerability, which was classified as critical, was found in Tenda AC7 up to 15.03.06.44. This affects the function formSetFirewallCfg of the file /goform/SetFirewallCfg. The manipulation of the argument firewallEn leads to stack-based buffer overflow. It is possible to initiate the attack remotely. The exploit has been disclosed to the public and may be used.

A vulnerability has been found in Tenda M3 1.0.0.13(4903). The impacted element is an unknown function of the file /goform/exeCommand. Such manipulation of the argument cmdinput leads to stack-based buffer overflow. The attack can be launched remotely. The exploit has been disclosed to the public and may be used.

A buffer copy without checking size of input vulnerability has been reported to affect several QNAP operating system versions. If exploited, the vulnerability could allow users to execute code via a network. We have already fixed the vulnerability in the following versions: QTS 5.1.6.2722 build 20240402 and later QuTS hero h5.1.6.2734 build 20240414 and later

A vulnerability, which was classified as critical, has been found in D-Link DAP-1320 1.00. Affected by this issue is the function replace_special_char of the file /storagein.pd-XXXXXX. The manipulation leads to stack-based buffer overflow. The attack may be launched remotely. The exploit has been disclosed to the public and may be used. This vulnerability only affects products that are no longer supported by the maintainer.

A vulnerability was found in Tenda AC8 16.03.34.06 and classified as critical. This issue affects the function sub_49E098 of the file /goform/SetIpMacBind of the component Parameter Handler. The manipulation of the argument list leads to stack-based buffer overflow. The attack may be initiated remotely. The exploit has been disclosed to the public and may be used.

A vulnerability, which was classified as critical, has been found in Tenda AC6 15.03.05.16. Affected by this issue is some unknown functionality of the file /goform/WifiExtraSet. The manipulation of the argument wpapsk_crypto leads to stack-based buffer overflow. The attack may be launched remotely. The exploit has been disclosed to the public and may be used.

A vulnerability was found in UTT 进取 512W up to 1.7.7-171114. This vulnerability affects the function strcpy of the file /goform/formConfigNoticeConfig. The manipulation of the argument timestart results in buffer overflow. The attack may be performed from remote. The exploit has been made public and could be used.

A vulnerability has been found in Tenda FH1201 1.2.0.14(408). Affected is the function sprintf of the file /goform/SetIpBind. Such manipulation of the argument page leads to stack-based buffer overflow. The attack may be performed from remote. The exploit has been disclosed to the public and may be used.

Multiple vulnerabilities in the web-based management interface of Cisco Small Business RV110W, RV130, RV130W, and RV215W Routers could allow an authenticated, remote attacker to execute arbitrary code or cause an affected device to restart unexpectedly. The vulnerabilities are due to improper validation of user-supplied input in the web-based management interface. An attacker could exploit these vulnerabilities by sending crafted HTTP requests to an affected device. A successful exploit could allow the attacker to execute arbitrary code as the root user on the underlying operating system or cause the device to reload, resulting in a denial of service (DoS) condition. To exploit these vulnerabilities, an attacker would need to have valid administrator credentials on the affected device. Cisco has not released software updates that address these vulnerabilities.

A flaw has been found in UTT 进取 512W 1.7.7-171114. This affects the function strcpy of the file /goform/formFtpServerDirConfig. Executing a manipulation of the argument filename can lead to buffer overflow. The attack can be launched remotely. The exploit has been published and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

A security flaw has been discovered in Tenda AC21 up to 16.03.08.16. Affected by this vulnerability is the function sscanf of the file /goform/SetStaticRouteCfg. The manipulation of the argument list results in buffer overflow. The attack can be launched remotely. The exploit has been released to the public and may be exploited.

A vulnerability was detected in D-Link DWR-M920 up to 1.1.50. This affects the function sub_423848 of the file /boafrm/formParentControl. Performing manipulation of the argument submit-url results in buffer overflow. The attack is possible to be carried out remotely. The exploit is now public and may be used.

A weakness has been identified in Tenda M3 1.0.0.13(4903). Impacted is the function formSetRemoteInternetLanInfo of the file /goform/setInternetLanInfo. This manipulation of the argument portIp/portMask/portGateWay/portDns/portSecDns causes heap-based buffer overflow. It is possible to initiate the attack remotely. The exploit has been made available to the public and could be used for attacks.