In the Linux kernel, the following vulnerability has been resolved: wifi: rtlwifi: Fix global-out-of-bounds bug in _rtl8812ae_phy_set_txpower_limit() There is a global-out-of-bounds reported by KASAN: BUG: KASAN: global-out-of-bounds in _rtl8812ae_eq_n_byte.part.0+0x3d/0x84 [rtl8821ae] Read of size 1 at addr ffffffffa0773c43 by task NetworkManager/411 CPU: 6 PID: 411 Comm: NetworkManager Tainted: G D 6.1.0-rc8+ #144 e15588508517267d37 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), Call Trace: <TASK> ... kasan_report+0xbb/0x1c0 _rtl8812ae_eq_n_byte.part.0+0x3d/0x84 [rtl8821ae] rtl8821ae_phy_bb_config.cold+0x346/0x641 [rtl8821ae] rtl8821ae_hw_init+0x1f5e/0x79b0 [rtl8821ae] ... </TASK> The root cause of the problem is that the comparison order of "prate_section" in _rtl8812ae_phy_set_txpower_limit() is wrong. The _rtl8812ae_eq_n_byte() is used to compare the first n bytes of the two strings from tail to head, which causes the problem. In the _rtl8812ae_phy_set_txpower_limit(), it was originally intended to meet this requirement by carefully designing the comparison order. For example, "pregulation" and "pbandwidth" are compared in order of length from small to large, first is 3 and last is 4. However, the comparison order of "prate_section" dose not obey such order requirement, therefore when "prate_section" is "HT", when comparing from tail to head, it will lead to access out of bounds in _rtl8812ae_eq_n_byte(). As mentioned above, the _rtl8812ae_eq_n_byte() has the same function as strcmp(), so just strcmp() is enough. Fix it by removing _rtl8812ae_eq_n_byte() and use strcmp() barely. Although it can be fixed by adjusting the comparison order of "prate_section", this may cause the value of "rate_section" to not be from 0 to 5. In addition, commit "21e4b0726dc6" not only moved driver from staging to regular tree, but also added setting txpower limit function during the driver config phase, so the problem was introduced by this commit.

In the Linux kernel, the following vulnerability has been resolved: bpf: Propagate error from htab_lock_bucket() to userspace In __htab_map_lookup_and_delete_batch() if htab_lock_bucket() returns -EBUSY, it will go to next bucket. Going to next bucket may not only skip the elements in current bucket silently, but also incur out-of-bound memory access or expose kernel memory to userspace if current bucket_cnt is greater than bucket_size or zero. Fixing it by stopping batch operation and returning -EBUSY when htab_lock_bucket() fails, and the application can retry or skip the busy batch as needed.

In the Linux kernel, the following vulnerability has been resolved: dm raid: fix address sanitizer warning in raid_status There is this warning when using a kernel with the address sanitizer and running this testsuite: https://gitlab.com/cki-project/kernel-tests/-/tree/main/storage/swraid/scsi_raid ================================================================== BUG: KASAN: slab-out-of-bounds in raid_status+0x1747/0x2820 [dm_raid] Read of size 4 at addr ffff888079d2c7e8 by task lvcreate/13319 CPU: 0 PID: 13319 Comm: lvcreate Not tainted 5.18.0-0.rc3.<snip> #1 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 Call Trace: <TASK> dump_stack_lvl+0x6a/0x9c print_address_description.constprop.0+0x1f/0x1e0 print_report.cold+0x55/0x244 kasan_report+0xc9/0x100 raid_status+0x1747/0x2820 [dm_raid] dm_ima_measure_on_table_load+0x4b8/0xca0 [dm_mod] table_load+0x35c/0x630 [dm_mod] ctl_ioctl+0x411/0x630 [dm_mod] dm_ctl_ioctl+0xa/0x10 [dm_mod] __x64_sys_ioctl+0x12a/0x1a0 do_syscall_64+0x5b/0x80 The warning is caused by reading conf->max_nr_stripes in raid_status. The code in raid_status reads mddev->private, casts it to struct r5conf and reads the entry max_nr_stripes. However, if we have different raid type than 4/5/6, mddev->private doesn't point to struct r5conf; it may point to struct r0conf, struct r1conf, struct r10conf or struct mpconf. If we cast a pointer to one of these structs to struct r5conf, we will be reading invalid memory and KASAN warns about it. Fix this bug by reading struct r5conf only if raid type is 4, 5 or 6.

In the Linux kernel, the following vulnerability has been resolved: cpufreq: qcom: fix writes in read-only memory region This commit fixes a kernel oops because of a write in some read-only memory: [ 9.068287] Unable to handle kernel write to read-only memory at virtual address ffff800009240ad8 ..snip.. [ 9.138790] Internal error: Oops: 9600004f [#1] PREEMPT SMP ..snip.. [ 9.269161] Call trace: [ 9.276271] __memcpy+0x5c/0x230 [ 9.278531] snprintf+0x58/0x80 [ 9.282002] qcom_cpufreq_msm8939_name_version+0xb4/0x190 [ 9.284869] qcom_cpufreq_probe+0xc8/0x39c ..snip.. The following line defines a pointer that point to a char buffer stored in read-only memory: char *pvs_name = "speedXX-pvsXX-vXX"; This pointer is meant to hold a template "speedXX-pvsXX-vXX" where the XX values get overridden by the qcom_cpufreq_krait_name_version function. Since the template is actually stored in read-only memory, when the function executes the following call we get an oops: snprintf(*pvs_name, sizeof("speedXX-pvsXX-vXX"), "speed%d-pvs%d-v%d", speed, pvs, pvs_ver); To fix this issue, we instead store the template name onto the stack by using the following syntax: char pvs_name_buffer[] = "speedXX-pvsXX-vXX"; Because the `pvs_name` needs to be able to be assigned to NULL, the template buffer is stored in the pvs_name_buffer and not under the pvs_name variable.

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: Validate buffer length while parsing index indx_read is called when we have some NTFS directory operations that need more information from the index buffers. This adds a sanity check to make sure the returned index buffer length is legit, or we may have some out-of-bound memory accesses. [ 560.897595] BUG: KASAN: slab-out-of-bounds in hdr_find_e.isra.0+0x10c/0x320 [ 560.898321] Read of size 2 at addr ffff888009497238 by task exp/245 [ 560.898760] [ 560.899129] CPU: 0 PID: 245 Comm: exp Not tainted 6.0.0-rc6 #37 [ 560.899505] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 [ 560.900170] Call Trace: [ 560.900407] <TASK> [ 560.900732] dump_stack_lvl+0x49/0x63 [ 560.901108] print_report.cold+0xf5/0x689 [ 560.901395] ? hdr_find_e.isra.0+0x10c/0x320 [ 560.901716] kasan_report+0xa7/0x130 [ 560.901950] ? hdr_find_e.isra.0+0x10c/0x320 [ 560.902208] __asan_load2+0x68/0x90 [ 560.902427] hdr_find_e.isra.0+0x10c/0x320 [ 560.902846] ? cmp_uints+0xe0/0xe0 [ 560.903363] ? cmp_sdh+0x90/0x90 [ 560.903883] ? ntfs_bread_run+0x190/0x190 [ 560.904196] ? rwsem_down_read_slowpath+0x750/0x750 [ 560.904969] ? ntfs_fix_post_read+0xe0/0x130 [ 560.905259] ? __kasan_check_write+0x14/0x20 [ 560.905599] ? up_read+0x1a/0x90 [ 560.905853] ? indx_read+0x22c/0x380 [ 560.906096] indx_find+0x2ef/0x470 [ 560.906352] ? indx_find_buffer+0x2d0/0x2d0 [ 560.906692] ? __kasan_kmalloc+0x88/0xb0 [ 560.906977] dir_search_u+0x196/0x2f0 [ 560.907220] ? ntfs_nls_to_utf16+0x450/0x450 [ 560.907464] ? __kasan_check_write+0x14/0x20 [ 560.907747] ? mutex_lock+0x8f/0xe0 [ 560.907970] ? __mutex_lock_slowpath+0x20/0x20 [ 560.908214] ? kmem_cache_alloc+0x143/0x4b0 [ 560.908459] ntfs_lookup+0xe0/0x100 [ 560.908788] __lookup_slow+0x116/0x220 [ 560.909050] ? lookup_fast+0x1b0/0x1b0 [ 560.909309] ? lookup_fast+0x13f/0x1b0 [ 560.909601] walk_component+0x187/0x230 [ 560.909944] link_path_walk.part.0+0x3f0/0x660 [ 560.910285] ? handle_lookup_down+0x90/0x90 [ 560.910618] ? path_init+0x642/0x6e0 [ 560.911084] ? percpu_counter_add_batch+0x6e/0xf0 [ 560.912559] ? __alloc_file+0x114/0x170 [ 560.913008] path_openat+0x19c/0x1d10 [ 560.913419] ? getname_flags+0x73/0x2b0 [ 560.913815] ? kasan_save_stack+0x3a/0x50 [ 560.914125] ? kasan_save_stack+0x26/0x50 [ 560.914542] ? __kasan_slab_alloc+0x6d/0x90 [ 560.914924] ? kmem_cache_alloc+0x143/0x4b0 [ 560.915339] ? getname_flags+0x73/0x2b0 [ 560.915647] ? getname+0x12/0x20 [ 560.916114] ? __x64_sys_open+0x4c/0x60 [ 560.916460] ? path_lookupat.isra.0+0x230/0x230 [ 560.916867] ? __isolate_free_page+0x2e0/0x2e0 [ 560.917194] do_filp_open+0x15c/0x1f0 [ 560.917448] ? may_open_dev+0x60/0x60 [ 560.917696] ? expand_files+0xa4/0x3a0 [ 560.917923] ? __kasan_check_write+0x14/0x20 [ 560.918185] ? _raw_spin_lock+0x88/0xdb [ 560.918409] ? _raw_spin_lock_irqsave+0x100/0x100 [ 560.918783] ? _find_next_bit+0x4a/0x130 [ 560.919026] ? _raw_spin_unlock+0x19/0x40 [ 560.919276] ? alloc_fd+0x14b/0x2d0 [ 560.919635] do_sys_openat2+0x32a/0x4b0 [ 560.920035] ? file_open_root+0x230/0x230 [ 560.920336] ? __rcu_read_unlock+0x5b/0x280 [ 560.920813] do_sys_open+0x99/0xf0 [ 560.921208] ? filp_open+0x60/0x60 [ 560.921482] ? exit_to_user_mode_prepare+0x49/0x180 [ 560.921867] __x64_sys_open+0x4c/0x60 [ 560.922128] do_syscall_64+0x3b/0x90 [ 560.922369] entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 560.923030] RIP: 0033:0x7f7dff2e4469 [ 560.923681] Code: 00 f3 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 088 [ 560.924451] RSP: 002b:00007ffd41a210b8 EFLAGS: 00000206 ORIG_RAX: 0000000000000002 [ 560.925168] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f7dff2e4469 [ 560.925655] RDX: 0000000000000000 RSI: 0000000000000002 RDI: ---truncated---

In the Linux kernel, the following vulnerability has been resolved: bpf: Do mark_chain_precision for ARG_CONST_ALLOC_SIZE_OR_ZERO Precision markers need to be propagated whenever we have an ARG_CONST_* style argument, as the verifier cannot consider imprecise scalars to be equivalent for the purposes of states_equal check when such arguments refine the return value (in this case, set mem_size for PTR_TO_MEM). The resultant mem_size for the R0 is derived from the constant value, and if the verifier incorrectly prunes states considering them equivalent where such arguments exist (by seeing that both registers have reg->precise as false in regsafe), we can end up with invalid programs passing the verifier which can do access beyond what should have been the correct mem_size in that explored state. To show a concrete example of the problem: 0000000000000000 <prog>: 0: r2 = *(u32 *)(r1 + 80) 1: r1 = *(u32 *)(r1 + 76) 2: r3 = r1 3: r3 += 4 4: if r3 > r2 goto +18 <LBB5_5> 5: w2 = 0 6: *(u32 *)(r1 + 0) = r2 7: r1 = *(u32 *)(r1 + 0) 8: r2 = 1 9: if w1 == 0 goto +1 <LBB5_3> 10: r2 = -1 0000000000000058 <LBB5_3>: 11: r1 = 0 ll 13: r3 = 0 14: call bpf_ringbuf_reserve 15: if r0 == 0 goto +7 <LBB5_5> 16: r1 = r0 17: r1 += 16777215 18: w2 = 0 19: *(u8 *)(r1 + 0) = r2 20: r1 = r0 21: r2 = 0 22: call bpf_ringbuf_submit 00000000000000b8 <LBB5_5>: 23: w0 = 0 24: exit For the first case, the single line execution's exploration will prune the search at insn 14 for the branch insn 9's second leg as it will be verified first using r2 = -1 (UINT_MAX), while as w1 at insn 9 will always be 0 so at runtime we don't get error for being greater than UINT_MAX/4 from bpf_ringbuf_reserve. The verifier during regsafe just sees reg->precise as false for both r2 registers in both states, hence considers them equal for purposes of states_equal. If we propagated precise markers using the backtracking support, we would use the precise marking to then ensure that old r2 (UINT_MAX) was within the new r2 (1) and this would never be true, so the verification would rightfully fail. The end result is that the out of bounds access at instruction 19 would be permitted without this fix. Note that reg->precise is always set to true when user does not have CAP_BPF (or when subprog count is greater than 1 (i.e. use of any static or global functions)), hence this is only a problem when precision marks need to be explicitly propagated (i.e. privileged users with CAP_BPF). A simplified test case has been included in the next patch to prevent future regressions.

In the Linux kernel, the following vulnerability has been resolved: clk: bcm: rpi: Prevent out-of-bounds access The while loop in raspberrypi_discover_clocks() relies on the assumption that the id of the last clock element is zero. Because this data comes from the Videocore firmware and it doesn't guarantuee such a behavior this could lead to out-of-bounds access. So fix this by providing a sentinel element.

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt76x0: fix oob access in mt76x0_phy_get_target_power After 'commit ba45841ca5eb ("wifi: mt76: mt76x02: simplify struct mt76x02_rate_power")', mt76x02 relies on ht[0-7] rate_power data for vht mcs{0,7}, while it uses vth[0-1] rate_power for vht mcs {8,9}. Fix a possible out-of-bound access in mt76x0_phy_get_target_power routine.

In the Linux kernel, the following vulnerability has been resolved: iio: adc: mp2629: fix potential array out of bound access Add sentinel at end of maps to avoid potential array out of bound access in iio core.

In the Linux kernel, the following vulnerability has been resolved: can: dev: fix skb drop check In commit a6d190f8c767 ("can: skb: drop tx skb if in listen only mode") the priv->ctrlmode element is read even on virtual CAN interfaces that do not create the struct can_priv at startup. This out-of-bounds read may lead to CAN frame drops for virtual CAN interfaces like vcan and vxcan. This patch mainly reverts the original commit and adds a new helper for CAN interface drivers that provide the required information in struct can_priv. [mkl: patch pch_can, too]

In the Linux kernel, the following vulnerability has been resolved: powercap: intel_rapl: fix UBSAN shift-out-of-bounds issue When value < time_unit, the parameter of ilog2() will be zero and the return value is -1. u64(-1) is too large for shift exponent and then will trigger shift-out-of-bounds: shift exponent 18446744073709551615 is too large for 32-bit type 'int' Call Trace: rapl_compute_time_window_core rapl_write_data_raw set_time_window store_constraint_time_window_us

In the Linux kernel, the following vulnerability has been resolved: binfmt_misc: fix shift-out-of-bounds in check_special_flags UBSAN reported a shift-out-of-bounds warning: left shift of 1 by 31 places cannot be represented in type 'int' Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x8d/0xcf lib/dump_stack.c:106 ubsan_epilogue+0xa/0x44 lib/ubsan.c:151 __ubsan_handle_shift_out_of_bounds+0x1e7/0x208 lib/ubsan.c:322 check_special_flags fs/binfmt_misc.c:241 [inline] create_entry fs/binfmt_misc.c:456 [inline] bm_register_write+0x9d3/0xa20 fs/binfmt_misc.c:654 vfs_write+0x11e/0x580 fs/read_write.c:582 ksys_write+0xcf/0x120 fs/read_write.c:637 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x34/0x80 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd RIP: 0033:0x4194e1 Since the type of Node's flags is unsigned long, we should define these macros with same type too.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Check correct bounds for stream encoder instances for DCN303 [Why & How] eng_id for DCN303 cannot be more than 1, since we have only two instances of stream encoders. Check the correct boundary condition for engine ID for DCN303 prevent the potential out of bounds access.

In the Linux kernel, the following vulnerability has been resolved: tracing: Fix reading strings from synthetic events The follow commands caused a crash: # cd /sys/kernel/tracing # echo 's:open char file[]' > dynamic_events # echo 'hist:keys=common_pid:file=filename:onchange($file).trace(open,$file)' > events/syscalls/sys_enter_openat/trigger' # echo 1 > events/synthetic/open/enable BOOM! The problem is that the synthetic event field "char file[]" will read the value given to it as a string without any memory checks to make sure the address is valid. The above example will pass in the user space address and the sythetic event code will happily call strlen() on it and then strscpy() where either one will cause an oops when accessing user space addresses. Use the helper functions from trace_kprobe and trace_eprobe that can read strings safely (and actually succeed when the address is from user space and the memory is mapped in). Now the above can show: packagekitd-1721 [000] ...2. 104.597170: open: file=/usr/lib/rpm/fileattrs/cmake.attr in:imjournal-978 [006] ...2. 104.599642: open: file=/var/lib/rsyslog/imjournal.state.tmp packagekitd-1721 [000] ...2. 104.626308: open: file=/usr/lib/rpm/fileattrs/debuginfo.attr

In the Linux kernel, the following vulnerability has been resolved: KVM: x86: smm: number of GPRs in the SMRAM image depends on the image format On 64 bit host, if the guest doesn't have X86_FEATURE_LM, KVM will access 16 gprs to 32-bit smram image, causing out-ouf-bound ram access. On 32 bit host, the rsm_load_state_64/enter_smm_save_state_64 is compiled out, thus access overflow can't happen.

In the Linux kernel, the following vulnerability has been resolved: hwmon: (gpio-fan) Fix array out of bounds access The driver does not check if the cooling state passed to gpio_fan_set_cur_state() exceeds the maximum cooling state as stored in fan_data->num_speeds. Since the cooling state is later used as an array index in set_fan_speed(), an array out of bounds access can occur. This can be exploited by setting the state of the thermal cooling device to arbitrary values, causing for example a kernel oops when unavailable memory is accessed this way. Example kernel oops: [ 807.987276] Unable to handle kernel paging request at virtual address ffffff80d0588064 [ 807.987369] Mem abort info: [ 807.987398] ESR = 0x96000005 [ 807.987428] EC = 0x25: DABT (current EL), IL = 32 bits [ 807.987477] SET = 0, FnV = 0 [ 807.987507] EA = 0, S1PTW = 0 [ 807.987536] FSC = 0x05: level 1 translation fault [ 807.987570] Data abort info: [ 807.987763] ISV = 0, ISS = 0x00000005 [ 807.987801] CM = 0, WnR = 0 [ 807.987832] swapper pgtable: 4k pages, 39-bit VAs, pgdp=0000000001165000 [ 807.987872] [ffffff80d0588064] pgd=0000000000000000, p4d=0000000000000000, pud=0000000000000000 [ 807.987961] Internal error: Oops: 96000005 [#1] PREEMPT SMP [ 807.987992] Modules linked in: cmac algif_hash aes_arm64 algif_skcipher af_alg bnep hci_uart btbcm bluetooth ecdh_generic ecc 8021q garp stp llc snd_soc_hdmi_codec brcmfmac vc4 brcmutil cec drm_kms_helper snd_soc_core cfg80211 snd_compress bcm2835_codec(C) snd_pcm_dmaengine syscopyarea bcm2835_isp(C) bcm2835_v4l2(C) sysfillrect v4l2_mem2mem bcm2835_mmal_vchiq(C) raspberrypi_hwmon sysimgblt videobuf2_dma_contig videobuf2_vmalloc fb_sys_fops videobuf2_memops rfkill videobuf2_v4l2 videobuf2_common i2c_bcm2835 snd_bcm2835(C) videodev snd_pcm snd_timer snd mc vc_sm_cma(C) gpio_fan uio_pdrv_genirq uio drm fuse drm_panel_orientation_quirks backlight ip_tables x_tables ipv6 [ 807.988508] CPU: 0 PID: 1321 Comm: bash Tainted: G C 5.15.56-v8+ #1575 [ 807.988548] Hardware name: Raspberry Pi 3 Model B Rev 1.2 (DT) [ 807.988574] pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 807.988608] pc : set_fan_speed.part.5+0x34/0x80 [gpio_fan] [ 807.988654] lr : gpio_fan_set_cur_state+0x34/0x50 [gpio_fan] [ 807.988691] sp : ffffffc008cf3bd0 [ 807.988710] x29: ffffffc008cf3bd0 x28: ffffff80019edac0 x27: 0000000000000000 [ 807.988762] x26: 0000000000000000 x25: 0000000000000000 x24: ffffff800747c920 [ 807.988787] x23: 000000000000000a x22: ffffff800369f000 x21: 000000001999997c [ 807.988854] x20: ffffff800369f2e8 x19: ffffff8002ae8080 x18: 0000000000000000 [ 807.988877] x17: 0000000000000000 x16: 0000000000000000 x15: 000000559e271b70 [ 807.988938] x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000 [ 807.988960] x11: 0000000000000000 x10: ffffffc008cf3c20 x9 : ffffffcfb60c741c [ 807.989018] x8 : 000000000000000a x7 : 00000000ffffffc9 x6 : 0000000000000009 [ 807.989040] x5 : 000000000000002a x4 : 0000000000000000 x3 : ffffff800369f2e8 [ 807.989062] x2 : 000000000000e780 x1 : 0000000000000001 x0 : ffffff80d0588060 [ 807.989084] Call trace: [ 807.989091] set_fan_speed.part.5+0x34/0x80 [gpio_fan] [ 807.989113] gpio_fan_set_cur_state+0x34/0x50 [gpio_fan] [ 807.989199] cur_state_store+0x84/0xd0 [ 807.989221] dev_attr_store+0x20/0x38 [ 807.989262] sysfs_kf_write+0x4c/0x60 [ 807.989282] kernfs_fop_write_iter+0x130/0x1c0 [ 807.989298] new_sync_write+0x10c/0x190 [ 807.989315] vfs_write+0x254/0x378 [ 807.989362] ksys_write+0x70/0xf8 [ 807.989379] __arm64_sys_write+0x24/0x30 [ 807.989424] invoke_syscall+0x4c/0x110 [ 807.989442] el0_svc_common.constprop.3+0xfc/0x120 [ 807.989458] do_el0_svc+0x2c/0x90 [ 807.989473] el0_svc+0x24/0x60 [ 807.989544] el0t_64_sync_handler+0x90/0xb8 [ 807.989558] el0t_64_sync+0x1a0/0x1a4 [ 807.989579] Code: b9403801 f9402800 7100003f 8b35cc00 (b9400416) [ 807.989627] ---[ end t ---truncated---

In the Linux kernel, the following vulnerability has been resolved: wifi: brcmfmac: Check the count value of channel spec to prevent out-of-bounds reads This patch fixes slab-out-of-bounds reads in brcmfmac that occur in brcmf_construct_chaninfo() and brcmf_enable_bw40_2g() when the count value of channel specifications provided by the device is greater than the length of 'list->element[]', decided by the size of the 'list' allocated with kzalloc(). The patch adds checks that make the functions free the buffer and return -EINVAL if that is the case. Note that the negative return is handled by the caller, brcmf_setup_wiphybands() or brcmf_cfg80211_attach(). Found by a modified version of syzkaller. Crash Report from brcmf_construct_chaninfo(): ================================================================== BUG: KASAN: slab-out-of-bounds in brcmf_setup_wiphybands+0x1238/0x1430 Read of size 4 at addr ffff888115f24600 by task kworker/0:2/1896 CPU: 0 PID: 1896 Comm: kworker/0:2 Tainted: G W O 5.14.0+ #132 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 Workqueue: usb_hub_wq hub_event Call Trace: dump_stack_lvl+0x57/0x7d print_address_description.constprop.0.cold+0x93/0x334 kasan_report.cold+0x83/0xdf brcmf_setup_wiphybands+0x1238/0x1430 brcmf_cfg80211_attach+0x2118/0x3fd0 brcmf_attach+0x389/0xd40 brcmf_usb_probe+0x12de/0x1690 usb_probe_interface+0x25f/0x710 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 bus_for_each_drv+0x123/0x1a0 __device_attach+0x207/0x330 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 usb_set_configuration+0x984/0x1770 usb_generic_driver_probe+0x69/0x90 usb_probe_device+0x9c/0x220 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 bus_for_each_drv+0x123/0x1a0 __device_attach+0x207/0x330 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 usb_new_device.cold+0x463/0xf66 hub_event+0x10d5/0x3330 process_one_work+0x873/0x13e0 worker_thread+0x8b/0xd10 kthread+0x379/0x450 ret_from_fork+0x1f/0x30 Allocated by task 1896: kasan_save_stack+0x1b/0x40 __kasan_kmalloc+0x7c/0x90 kmem_cache_alloc_trace+0x19e/0x330 brcmf_setup_wiphybands+0x290/0x1430 brcmf_cfg80211_attach+0x2118/0x3fd0 brcmf_attach+0x389/0xd40 brcmf_usb_probe+0x12de/0x1690 usb_probe_interface+0x25f/0x710 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 bus_for_each_drv+0x123/0x1a0 __device_attach+0x207/0x330 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 usb_set_configuration+0x984/0x1770 usb_generic_driver_probe+0x69/0x90 usb_probe_device+0x9c/0x220 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 bus_for_each_drv+0x123/0x1a0 __device_attach+0x207/0x330 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 usb_new_device.cold+0x463/0xf66 hub_event+0x10d5/0x3330 process_one_work+0x873/0x13e0 worker_thread+0x8b/0xd10 kthread+0x379/0x450 ret_from_fork+0x1f/0x30 The buggy address belongs to the object at ffff888115f24000 which belongs to the cache kmalloc-2k of size 2048 The buggy address is located 1536 bytes inside of 2048-byte region [ffff888115f24000, ffff888115f24800) Memory state around the buggy address: ffff888115f24500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff888115f24580: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffff888115f24600: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffff888115f24680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff888115f24700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ================================================================== Crash Report from brcmf_enable_bw40_2g(): ========== ---truncated---

In the Linux kernel, the following vulnerability has been resolved: habanalabs/gaudi: fix shift out of bounds When validating NIC queues, queue offset calculation must be performed only for NIC queues.

In the Linux kernel, the following vulnerability has been resolved: selinux: Add boundary check in put_entry() Just like next_entry(), boundary check is necessary to prevent memory out-of-bound access.

In the Linux kernel, the following vulnerability has been resolved: ext4: fix potential out of bound read in ext4_fc_replay_scan() For scan loop must ensure that at least EXT4_FC_TAG_BASE_LEN space. If remain space less than EXT4_FC_TAG_BASE_LEN which will lead to out of bound read when mounting corrupt file system image. ADD_RANGE/HEAD/TAIL is needed to add extra check when do journal scan, as this three tags will read data during scan, tag length couldn't less than data length which will read.

In the Linux kernel, the following vulnerability has been resolved: fs: jfs: fix shift-out-of-bounds in dbDiscardAG This should be applied to most URSAN bugs found recently by syzbot, by guarding the dbMount. As syzbot feeding rubbish into the bmap descriptor.

In the Linux kernel, the following vulnerability has been resolved: spmi: trace: fix stack-out-of-bound access in SPMI tracing functions trace_spmi_write_begin() and trace_spmi_read_end() both call memcpy() with a length of "len + 1". This leads to one extra byte being read beyond the end of the specified buffer. Fix this out-of-bound memory access by using a length of "len" instead. Here is a KASAN log showing the issue: BUG: KASAN: stack-out-of-bounds in trace_event_raw_event_spmi_read_end+0x1d0/0x234 Read of size 2 at addr ffffffc0265b7540 by task thermal@2.0-ser/1314 ... Call trace: dump_backtrace+0x0/0x3e8 show_stack+0x2c/0x3c dump_stack_lvl+0xdc/0x11c print_address_description+0x74/0x384 kasan_report+0x188/0x268 kasan_check_range+0x270/0x2b0 memcpy+0x90/0xe8 trace_event_raw_event_spmi_read_end+0x1d0/0x234 spmi_read_cmd+0x294/0x3ac spmi_ext_register_readl+0x84/0x9c regmap_spmi_ext_read+0x144/0x1b0 [regmap_spmi] _regmap_raw_read+0x40c/0x754 regmap_raw_read+0x3a0/0x514 regmap_bulk_read+0x418/0x494 adc5_gen3_poll_wait_hs+0xe8/0x1e0 [qcom_spmi_adc5_gen3] ... __arm64_sys_read+0x4c/0x60 invoke_syscall+0x80/0x218 el0_svc_common+0xec/0x1c8 ... addr ffffffc0265b7540 is located in stack of task thermal@2.0-ser/1314 at offset 32 in frame: adc5_gen3_poll_wait_hs+0x0/0x1e0 [qcom_spmi_adc5_gen3] this frame has 1 object: [32, 33) 'status' Memory state around the buggy address: ffffffc0265b7400: 00 00 00 00 00 00 00 00 00 00 00 00 f1 f1 f1 f1 ffffffc0265b7480: 04 f3 f3 f3 00 00 00 00 00 00 00 00 00 00 00 00 >ffffffc0265b7500: 00 00 00 00 f1 f1 f1 f1 01 f3 f3 f3 00 00 00 00 ^ ffffffc0265b7580: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffffffc0265b7600: f1 f1 f1 f1 01 f2 07 f2 f2 f2 01 f3 00 00 00 00 ==================================================================

In the Linux kernel, the following vulnerability has been resolved: md-raid10: fix KASAN warning There's a KASAN warning in raid10_remove_disk when running the lvm test lvconvert-raid-reshape.sh. We fix this warning by verifying that the value "number" is valid. BUG: KASAN: slab-out-of-bounds in raid10_remove_disk+0x61/0x2a0 [raid10] Read of size 8 at addr ffff889108f3d300 by task mdX_raid10/124682 CPU: 3 PID: 124682 Comm: mdX_raid10 Not tainted 5.19.0-rc6 #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-2 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x34/0x44 print_report.cold+0x45/0x57a ? __lock_text_start+0x18/0x18 ? raid10_remove_disk+0x61/0x2a0 [raid10] kasan_report+0xa8/0xe0 ? raid10_remove_disk+0x61/0x2a0 [raid10] raid10_remove_disk+0x61/0x2a0 [raid10] Buffer I/O error on dev dm-76, logical block 15344, async page read ? __mutex_unlock_slowpath.constprop.0+0x1e0/0x1e0 remove_and_add_spares+0x367/0x8a0 [md_mod] ? super_written+0x1c0/0x1c0 [md_mod] ? mutex_trylock+0xac/0x120 ? _raw_spin_lock+0x72/0xc0 ? _raw_spin_lock_bh+0xc0/0xc0 md_check_recovery+0x848/0x960 [md_mod] raid10d+0xcf/0x3360 [raid10] ? sched_clock_cpu+0x185/0x1a0 ? rb_erase+0x4d4/0x620 ? var_wake_function+0xe0/0xe0 ? psi_group_change+0x411/0x500 ? preempt_count_sub+0xf/0xc0 ? _raw_spin_lock_irqsave+0x78/0xc0 ? __lock_text_start+0x18/0x18 ? raid10_sync_request+0x36c0/0x36c0 [raid10] ? preempt_count_sub+0xf/0xc0 ? _raw_spin_unlock_irqrestore+0x19/0x40 ? del_timer_sync+0xa9/0x100 ? try_to_del_timer_sync+0xc0/0xc0 ? _raw_spin_lock_irqsave+0x78/0xc0 ? __lock_text_start+0x18/0x18 ? _raw_spin_unlock_irq+0x11/0x24 ? __list_del_entry_valid+0x68/0xa0 ? finish_wait+0xa3/0x100 md_thread+0x161/0x260 [md_mod] ? unregister_md_personality+0xa0/0xa0 [md_mod] ? _raw_spin_lock_irqsave+0x78/0xc0 ? prepare_to_wait_event+0x2c0/0x2c0 ? unregister_md_personality+0xa0/0xa0 [md_mod] kthread+0x148/0x180 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork+0x1f/0x30 </TASK> Allocated by task 124495: kasan_save_stack+0x1e/0x40 __kasan_kmalloc+0x80/0xa0 setup_conf+0x140/0x5c0 [raid10] raid10_run+0x4cd/0x740 [raid10] md_run+0x6f9/0x1300 [md_mod] raid_ctr+0x2531/0x4ac0 [dm_raid] dm_table_add_target+0x2b0/0x620 [dm_mod] table_load+0x1c8/0x400 [dm_mod] ctl_ioctl+0x29e/0x560 [dm_mod] dm_compat_ctl_ioctl+0x7/0x20 [dm_mod] __do_compat_sys_ioctl+0xfa/0x160 do_syscall_64+0x90/0xc0 entry_SYSCALL_64_after_hwframe+0x46/0xb0 Last potentially related work creation: kasan_save_stack+0x1e/0x40 __kasan_record_aux_stack+0x9e/0xc0 kvfree_call_rcu+0x84/0x480 timerfd_release+0x82/0x140 L __fput+0xfa/0x400 task_work_run+0x80/0xc0 exit_to_user_mode_prepare+0x155/0x160 syscall_exit_to_user_mode+0x12/0x40 do_syscall_64+0x42/0xc0 entry_SYSCALL_64_after_hwframe+0x46/0xb0 Second to last potentially related work creation: kasan_save_stack+0x1e/0x40 __kasan_record_aux_stack+0x9e/0xc0 kvfree_call_rcu+0x84/0x480 timerfd_release+0x82/0x140 __fput+0xfa/0x400 task_work_run+0x80/0xc0 exit_to_user_mode_prepare+0x155/0x160 syscall_exit_to_user_mode+0x12/0x40 do_syscall_64+0x42/0xc0 entry_SYSCALL_64_after_hwframe+0x46/0xb0 The buggy address belongs to the object at ffff889108f3d200 which belongs to the cache kmalloc-256 of size 256 The buggy address is located 0 bytes to the right of 256-byte region [ffff889108f3d200, ffff889108f3d300) The buggy address belongs to the physical page: page:000000007ef2a34c refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1108f3c head:000000007ef2a34c order:2 compound_mapcount:0 compound_pincount:0 flags: 0x4000000000010200(slab|head|zone=2) raw: 4000000000010200 0000000000000000 dead000000000001 ffff889100042b40 raw: 0000000000000000 0000000080200020 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff889108f3d200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff889108f3d280: 00 00 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: s390/cio: fix out-of-bounds access on cio_ignore free The channel-subsystem-driver scans for newly available devices whenever device-IDs are removed from the cio_ignore list using a command such as: echo free >/proc/cio_ignore Since an I/O device scan might interfer with running I/Os, commit 172da89ed0ea ("s390/cio: avoid excessive path-verification requests") introduced an optimization to exclude online devices from the scan. The newly added check for online devices incorrectly assumes that an I/O-subchannel's drvdata points to a struct io_subchannel_private. For devices that are bound to a non-default I/O subchannel driver, such as the vfio_ccw driver, this results in an out-of-bounds read access during each scan. Fix this by changing the scan logic to rely on a driver-independent online indication. For this we can use struct subchannel->config.ena, which is the driver's requested subchannel-enabled state. Since I/Os can only be started on enabled subchannels, this matches the intent of the original optimization of not scanning devices where I/O might be running.

In the Linux kernel, the following vulnerability has been resolved: iommu/vt-d: avoid invalid memory access via node_online(NUMA_NO_NODE) KASAN reports: [ 4.668325][ T0] BUG: KASAN: wild-memory-access in dmar_parse_one_rhsa (arch/x86/include/asm/bitops.h:214 arch/x86/include/asm/bitops.h:226 include/asm-generic/bitops/instrumented-non-atomic.h:142 include/linux/nodemask.h:415 drivers/iommu/intel/dmar.c:497) [ 4.676149][ T0] Read of size 8 at addr 1fffffff85115558 by task swapper/0/0 [ 4.683454][ T0] [ 4.685638][ T0] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.19.0-rc3-00004-g0e862838f290 #1 [ 4.694331][ T0] Hardware name: Supermicro SYS-5018D-FN4T/X10SDV-8C-TLN4F, BIOS 1.1 03/02/2016 [ 4.703196][ T0] Call Trace: [ 4.706334][ T0] <TASK> [ 4.709133][ T0] ? dmar_parse_one_rhsa (arch/x86/include/asm/bitops.h:214 arch/x86/include/asm/bitops.h:226 include/asm-generic/bitops/instrumented-non-atomic.h:142 include/linux/nodemask.h:415 drivers/iommu/intel/dmar.c:497) after converting the type of the first argument (@nr, bit number) of arch_test_bit() from `long` to `unsigned long`[0]. Under certain conditions (for example, when ACPI NUMA is disabled via command line), pxm_to_node() can return %NUMA_NO_NODE (-1). It is valid 'magic' number of NUMA node, but not valid bit number to use in bitops. node_online() eventually descends to test_bit() without checking for the input, assuming it's on caller side (which might be good for perf-critical tasks). There, -1 becomes %ULONG_MAX which leads to an insane array index when calculating bit position in memory. For now, add an explicit check for @node being not %NUMA_NO_NODE before calling test_bit(). The actual logics didn't change here at all. [0] https://github.com/norov/linux/commit/0e862838f290147ea9c16db852d8d494b552d38d

In the Linux kernel, the following vulnerability has been resolved: drm/fb-helper: Fix out-of-bounds access Clip memory range to screen-buffer size to avoid out-of-bounds access in fbdev deferred I/O's damage handling. Fbdev's deferred I/O can only track pages. From the range of pages, the damage handler computes the clipping rectangle for the display update. If the fbdev screen buffer ends near the beginning of a page, that page could contain more scanlines. The damage handler would then track these non-existing scanlines as dirty and provoke an out-of-bounds access during the screen update. Hence, clip the maximum memory range to the size of the screen buffer. While at it, rename the variables min/max to min_off/max_off in drm_fb_helper_deferred_io(). This avoids confusion with the macros of the same name.

In the Linux kernel, the following vulnerability has been resolved: wifi: brcmfmac: Fix potential shift-out-of-bounds in brcmf_fw_alloc_request() This patch fixes a shift-out-of-bounds in brcmfmac that occurs in BIT(chiprev) when a 'chiprev' provided by the device is too large. It should also not be equal to or greater than BITS_PER_TYPE(u32) as we do bitwise AND with a u32 variable and BIT(chiprev). The patch adds a check that makes the function return NULL if that is the case. Note that the NULL case is later handled by the bus-specific caller, brcmf_usb_probe_cb() or brcmf_usb_reset_resume(), for example. Found by a modified version of syzkaller. UBSAN: shift-out-of-bounds in drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c shift exponent 151055786 is too large for 64-bit type 'long unsigned int' CPU: 0 PID: 1885 Comm: kworker/0:2 Tainted: G O 5.14.0+ #132 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 Workqueue: usb_hub_wq hub_event Call Trace: dump_stack_lvl+0x57/0x7d ubsan_epilogue+0x5/0x40 __ubsan_handle_shift_out_of_bounds.cold+0x53/0xdb ? lock_chain_count+0x20/0x20 brcmf_fw_alloc_request.cold+0x19/0x3ea ? brcmf_fw_get_firmwares+0x250/0x250 ? brcmf_usb_ioctl_resp_wait+0x1a7/0x1f0 brcmf_usb_get_fwname+0x114/0x1a0 ? brcmf_usb_reset_resume+0x120/0x120 ? number+0x6c4/0x9a0 brcmf_c_process_clm_blob+0x168/0x590 ? put_dec+0x90/0x90 ? enable_ptr_key_workfn+0x20/0x20 ? brcmf_common_pd_remove+0x50/0x50 ? rcu_read_lock_sched_held+0xa1/0xd0 brcmf_c_preinit_dcmds+0x673/0xc40 ? brcmf_c_set_joinpref_default+0x100/0x100 ? rcu_read_lock_sched_held+0xa1/0xd0 ? rcu_read_lock_bh_held+0xb0/0xb0 ? lock_acquire+0x19d/0x4e0 ? find_held_lock+0x2d/0x110 ? brcmf_usb_deq+0x1cc/0x260 ? mark_held_locks+0x9f/0xe0 ? lockdep_hardirqs_on_prepare+0x273/0x3e0 ? _raw_spin_unlock_irqrestore+0x47/0x50 ? trace_hardirqs_on+0x1c/0x120 ? brcmf_usb_deq+0x1a7/0x260 ? brcmf_usb_rx_fill_all+0x5a/0xf0 brcmf_attach+0x246/0xd40 ? wiphy_new_nm+0x1476/0x1d50 ? kmemdup+0x30/0x40 brcmf_usb_probe+0x12de/0x1690 ? brcmf_usbdev_qinit.constprop.0+0x470/0x470 usb_probe_interface+0x25f/0x710 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 ? usb_match_id.part.0+0x88/0xc0 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 ? driver_allows_async_probing+0x120/0x120 bus_for_each_drv+0x123/0x1a0 ? bus_rescan_devices+0x20/0x20 ? lockdep_hardirqs_on_prepare+0x273/0x3e0 ? trace_hardirqs_on+0x1c/0x120 __device_attach+0x207/0x330 ? device_bind_driver+0xb0/0xb0 ? kobject_uevent_env+0x230/0x12c0 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 ? __mutex_unlock_slowpath+0xe7/0x660 ? __fw_devlink_link_to_suppliers+0x550/0x550 usb_set_configuration+0x984/0x1770 ? kernfs_create_link+0x175/0x230 usb_generic_driver_probe+0x69/0x90 usb_probe_device+0x9c/0x220 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 ? driver_allows_async_probing+0x120/0x120 bus_for_each_drv+0x123/0x1a0 ? bus_rescan_devices+0x20/0x20 ? lockdep_hardirqs_on_prepare+0x273/0x3e0 ? trace_hardirqs_on+0x1c/0x120 __device_attach+0x207/0x330 ? device_bind_driver+0xb0/0xb0 ? kobject_uevent_env+0x230/0x12c0 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 ? __fw_devlink_link_to_suppliers+0x550/0x550 usb_new_device.cold+0x463/0xf66 ? hub_disconnect+0x400/0x400 ? _raw_spin_unlock_irq+0x24/0x30 hub_event+0x10d5/0x3330 ? hub_port_debounce+0x280/0x280 ? __lock_acquire+0x1671/0x5790 ? wq_calc_node_cpumask+0x170/0x2a0 ? lock_release+0x640/0x640 ? rcu_read_lock_sched_held+0xa1/0xd0 ? rcu_read_lock_bh_held+0xb0/0xb0 ? lockdep_hardirqs_on_prepare+0x273/0x3e0 process_one_work+0x873/0x13e0 ? lock_release+0x640/0x640 ? pwq_dec_nr_in_flight+0x320/0x320 ? rwlock_bug.part.0+0x90/0x90 worker_thread+0x8b/0xd10 ? __kthread_parkme+0xd9/0x1d0 ? pr ---truncated---

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix shift-out-of-bounds/overflow in nilfs_sb2_bad_offset() Patch series "nilfs2: fix UBSAN shift-out-of-bounds warnings on mount time". The first patch fixes a bug reported by syzbot, and the second one fixes the remaining bug of the same kind. Although they are triggered by the same super block data anomaly, I divided it into the above two because the details of the issues and how to fix it are different. Both are required to eliminate the shift-out-of-bounds issues at mount time. This patch (of 2): If the block size exponent information written in an on-disk superblock is corrupted, nilfs_sb2_bad_offset helper function can trigger shift-out-of-bounds warning followed by a kernel panic (if panic_on_warn is set): shift exponent 38983 is too large for 64-bit type 'unsigned long long' Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x1b1/0x28e lib/dump_stack.c:106 ubsan_epilogue lib/ubsan.c:151 [inline] __ubsan_handle_shift_out_of_bounds+0x33d/0x3b0 lib/ubsan.c:322 nilfs_sb2_bad_offset fs/nilfs2/the_nilfs.c:449 [inline] nilfs_load_super_block+0xdf5/0xe00 fs/nilfs2/the_nilfs.c:523 init_nilfs+0xb7/0x7d0 fs/nilfs2/the_nilfs.c:577 nilfs_fill_super+0xb1/0x5d0 fs/nilfs2/super.c:1047 nilfs_mount+0x613/0x9b0 fs/nilfs2/super.c:1317 ... In addition, since nilfs_sb2_bad_offset() performs multiplication without considering the upper bound, the computation may overflow if the disk layout parameters are not normal. This fixes these issues by inserting preliminary sanity checks for those parameters and by converting the comparison from one involving multiplication and left bit-shifting to one using division and right bit-shifting.

In the Linux kernel, the following vulnerability has been resolved: exfat: check if cluster num is valid Syzbot reported slab-out-of-bounds read in exfat_clear_bitmap. This was triggered by reproducer calling truncute with size 0, which causes the following trace: BUG: KASAN: slab-out-of-bounds in exfat_clear_bitmap+0x147/0x490 fs/exfat/balloc.c:174 Read of size 8 at addr ffff888115aa9508 by task syz-executor251/365 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack_lvl+0x1e2/0x24b lib/dump_stack.c:118 print_address_description+0x81/0x3c0 mm/kasan/report.c:233 __kasan_report mm/kasan/report.c:419 [inline] kasan_report+0x1a4/0x1f0 mm/kasan/report.c:436 __asan_report_load8_noabort+0x14/0x20 mm/kasan/report_generic.c:309 exfat_clear_bitmap+0x147/0x490 fs/exfat/balloc.c:174 exfat_free_cluster+0x25a/0x4a0 fs/exfat/fatent.c:181 __exfat_truncate+0x99e/0xe00 fs/exfat/file.c:217 exfat_truncate+0x11b/0x4f0 fs/exfat/file.c:243 exfat_setattr+0xa03/0xd40 fs/exfat/file.c:339 notify_change+0xb76/0xe10 fs/attr.c:336 do_truncate+0x1ea/0x2d0 fs/open.c:65 Move the is_valid_cluster() helper from fatent.c to a common header to make it reusable in other *.c files. And add is_valid_cluster() to validate if cluster number is within valid range in exfat_clear_bitmap() and exfat_set_bitmap().

In the Linux kernel, the following vulnerability has been resolved: dlm: fix plock invalid read This patch fixes an invalid read showed by KASAN. A unlock will allocate a "struct plock_op" and a followed send_op() will append it to a global send_list data structure. In some cases a followed dev_read() moves it to recv_list and dev_write() will cast it to "struct plock_xop" and access fields which are only available in those structures. At this point an invalid read happens by accessing those fields. To fix this issue the "callback" field is moved to "struct plock_op" to indicate that a cast to "plock_xop" is allowed and does the additional "plock_xop" handling if set. Example of the KASAN output which showed the invalid read: [ 2064.296453] ================================================================== [ 2064.304852] BUG: KASAN: slab-out-of-bounds in dev_write+0x52b/0x5a0 [dlm] [ 2064.306491] Read of size 8 at addr ffff88800ef227d8 by task dlm_controld/7484 [ 2064.308168] [ 2064.308575] CPU: 0 PID: 7484 Comm: dlm_controld Kdump: loaded Not tainted 5.14.0+ #9 [ 2064.310292] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 [ 2064.311618] Call Trace: [ 2064.312218] dump_stack_lvl+0x56/0x7b [ 2064.313150] print_address_description.constprop.8+0x21/0x150 [ 2064.314578] ? dev_write+0x52b/0x5a0 [dlm] [ 2064.315610] ? dev_write+0x52b/0x5a0 [dlm] [ 2064.316595] kasan_report.cold.14+0x7f/0x11b [ 2064.317674] ? dev_write+0x52b/0x5a0 [dlm] [ 2064.318687] dev_write+0x52b/0x5a0 [dlm] [ 2064.319629] ? dev_read+0x4a0/0x4a0 [dlm] [ 2064.320713] ? bpf_lsm_kernfs_init_security+0x10/0x10 [ 2064.321926] vfs_write+0x17e/0x930 [ 2064.322769] ? __fget_light+0x1aa/0x220 [ 2064.323753] ksys_write+0xf1/0x1c0 [ 2064.324548] ? __ia32_sys_read+0xb0/0xb0 [ 2064.325464] do_syscall_64+0x3a/0x80 [ 2064.326387] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 2064.327606] RIP: 0033:0x7f807e4ba96f [ 2064.328470] Code: 89 54 24 18 48 89 74 24 10 89 7c 24 08 e8 39 87 f8 ff 48 8b 54 24 18 48 8b 74 24 10 41 89 c0 8b 7c 24 08 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 31 44 89 c7 48 89 44 24 08 e8 7c 87 f8 ff 48 [ 2064.332902] RSP: 002b:00007ffd50cfe6e0 EFLAGS: 00000293 ORIG_RAX: 0000000000000001 [ 2064.334658] RAX: ffffffffffffffda RBX: 000055cc3886eb30 RCX: 00007f807e4ba96f [ 2064.336275] RDX: 0000000000000040 RSI: 00007ffd50cfe7e0 RDI: 0000000000000010 [ 2064.337980] RBP: 00007ffd50cfe7e0 R08: 0000000000000000 R09: 0000000000000001 [ 2064.339560] R10: 000055cc3886eb30 R11: 0000000000000293 R12: 000055cc3886eb80 [ 2064.341237] R13: 000055cc3886eb00 R14: 000055cc3886f590 R15: 0000000000000001 [ 2064.342857] [ 2064.343226] Allocated by task 12438: [ 2064.344057] kasan_save_stack+0x1c/0x40 [ 2064.345079] __kasan_kmalloc+0x84/0xa0 [ 2064.345933] kmem_cache_alloc_trace+0x13b/0x220 [ 2064.346953] dlm_posix_unlock+0xec/0x720 [dlm] [ 2064.348811] do_lock_file_wait.part.32+0xca/0x1d0 [ 2064.351070] fcntl_setlk+0x281/0xbc0 [ 2064.352879] do_fcntl+0x5e4/0xfe0 [ 2064.354657] __x64_sys_fcntl+0x11f/0x170 [ 2064.356550] do_syscall_64+0x3a/0x80 [ 2064.358259] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 2064.360745] [ 2064.361511] Last potentially related work creation: [ 2064.363957] kasan_save_stack+0x1c/0x40 [ 2064.365811] __kasan_record_aux_stack+0xaf/0xc0 [ 2064.368100] call_rcu+0x11b/0xf70 [ 2064.369785] dlm_process_incoming_buffer+0x47d/0xfd0 [dlm] [ 2064.372404] receive_from_sock+0x290/0x770 [dlm] [ 2064.374607] process_recv_sockets+0x32/0x40 [dlm] [ 2064.377290] process_one_work+0x9a8/0x16e0 [ 2064.379357] worker_thread+0x87/0xbf0 [ 2064.381188] kthread+0x3ac/0x490 [ 2064.383460] ret_from_fork+0x22/0x30 [ 2064.385588] [ 2064.386518] Second to last potentially related work creation: [ 2064.389219] kasan_save_stack+0x1c/0x40 [ 2064.391043] __kasan_record_aux_stack+0xaf/0xc0 [ 2064.393303] call_rcu+0x11b/0xf70 [ 2064.394885] dlm_process_incoming_buffer+0x47d/0xfd0 [dlm] [ 2064.397694] receive_from_sock+0x290/0x770 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: iio: health: afe4403: Fix oob read in afe4403_read_raw KASAN report out-of-bounds read as follows: BUG: KASAN: global-out-of-bounds in afe4403_read_raw+0x42e/0x4c0 Read of size 4 at addr ffffffffc02ac638 by task cat/279 Call Trace: afe4403_read_raw iio_read_channel_info dev_attr_show The buggy address belongs to the variable: afe4403_channel_leds+0x18/0xffffffffffffe9e0 This issue can be reproduced by singe command: $ cat /sys/bus/spi/devices/spi0.0/iio\:device0/in_intensity6_raw The array size of afe4403_channel_leds is less than channels, so access with chan->address cause OOB read in afe4403_read_raw. Fix it by moving access before use it.

In the Linux kernel, the following vulnerability has been resolved: ASoC: cs35l41: Fix an out-of-bounds access in otp_packed_element_t The CS35L41_NUM_OTP_ELEM is 100, but only 99 entries are defined in the array otp_map_1/2[CS35L41_NUM_OTP_ELEM], this will trigger UBSAN to report a shift-out-of-bounds warning in the cs35l41_otp_unpack() since the last entry in the array will result in GENMASK(-1, 0). UBSAN reports this problem: UBSAN: shift-out-of-bounds in /home/hwang4/build/jammy/jammy/sound/soc/codecs/cs35l41-lib.c:836:8 shift exponent 64 is too large for 64-bit type 'long unsigned int' CPU: 10 PID: 595 Comm: systemd-udevd Not tainted 5.15.0-23-generic #23 Hardware name: LENOVO \x02MFG_IN_GO/\x02MFG_IN_GO, BIOS N3GET19W (1.00 ) 03/11/2022 Call Trace: <TASK> show_stack+0x52/0x58 dump_stack_lvl+0x4a/0x5f dump_stack+0x10/0x12 ubsan_epilogue+0x9/0x45 __ubsan_handle_shift_out_of_bounds.cold+0x61/0xef ? regmap_unlock_mutex+0xe/0x10 cs35l41_otp_unpack.cold+0x1c6/0x2b2 [snd_soc_cs35l41_lib] cs35l41_hda_probe+0x24f/0x33a [snd_hda_scodec_cs35l41] cs35l41_hda_i2c_probe+0x65/0x90 [snd_hda_scodec_cs35l41_i2c] ? cs35l41_hda_i2c_remove+0x20/0x20 [snd_hda_scodec_cs35l41_i2c] i2c_device_probe+0x252/0x2b0

In the Linux kernel, the following vulnerability has been resolved: ASoC: codecs: rx-macro: fix accessing compander for aux AUX interpolator does not have compander, so check before accessing compander data for this. Without this checkan array of out bounds access will be made in comp_enabled[] array.

In the Linux kernel, the following vulnerability has been resolved: media: imx-jpeg: fix a bug of accessing array out of bounds When error occurs in parsing jpeg, the slot isn't acquired yet, it may be the default value MXC_MAX_SLOTS. If the driver access the slot using the incorrect slot number, it will access array out of bounds. The result is the driver will change num_domains, which follows slot_data in struct mxc_jpeg_dev. Then the driver won't detach the pm domain at rmmod, which will lead to kernel panic when trying to insmod again.

In the Linux kernel, the following vulnerability has been resolved: powerpc/xive/spapr: correct bitmap allocation size kasan detects access beyond the end of the xibm->bitmap allocation: BUG: KASAN: slab-out-of-bounds in _find_first_zero_bit+0x40/0x140 Read of size 8 at addr c00000001d1d0118 by task swapper/0/1 CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.19.0-rc2-00001-g90df023b36dd #28 Call Trace: [c00000001d98f770] [c0000000012baab8] dump_stack_lvl+0xac/0x108 (unreliable) [c00000001d98f7b0] [c00000000068faac] print_report+0x37c/0x710 [c00000001d98f880] [c0000000006902c0] kasan_report+0x110/0x354 [c00000001d98f950] [c000000000692324] __asan_load8+0xa4/0xe0 [c00000001d98f970] [c0000000011c6ed0] _find_first_zero_bit+0x40/0x140 [c00000001d98f9b0] [c0000000000dbfbc] xive_spapr_get_ipi+0xcc/0x260 [c00000001d98fa70] [c0000000000d6d28] xive_setup_cpu_ipi+0x1e8/0x450 [c00000001d98fb30] [c000000004032a20] pSeries_smp_probe+0x5c/0x118 [c00000001d98fb60] [c000000004018b44] smp_prepare_cpus+0x944/0x9ac [c00000001d98fc90] [c000000004009f9c] kernel_init_freeable+0x2d4/0x640 [c00000001d98fd90] [c0000000000131e8] kernel_init+0x28/0x1d0 [c00000001d98fe10] [c00000000000cd54] ret_from_kernel_thread+0x5c/0x64 Allocated by task 0: kasan_save_stack+0x34/0x70 __kasan_kmalloc+0xb4/0xf0 __kmalloc+0x268/0x540 xive_spapr_init+0x4d0/0x77c pseries_init_irq+0x40/0x27c init_IRQ+0x44/0x84 start_kernel+0x2a4/0x538 start_here_common+0x1c/0x20 The buggy address belongs to the object at c00000001d1d0118 which belongs to the cache kmalloc-8 of size 8 The buggy address is located 0 bytes inside of 8-byte region [c00000001d1d0118, c00000001d1d0120) The buggy address belongs to the physical page: page:c00c000000074740 refcount:1 mapcount:0 mapping:0000000000000000 index:0xc00000001d1d0558 pfn:0x1d1d flags: 0x7ffff000000200(slab|node=0|zone=0|lastcpupid=0x7ffff) raw: 007ffff000000200 c00000001d0003c8 c00000001d0003c8 c00000001d010480 raw: c00000001d1d0558 0000000001e1000a 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: c00000001d1d0000: fc 00 fc fc fc fc fc fc fc fc fc fc fc fc fc fc c00000001d1d0080: fc fc 00 fc fc fc fc fc fc fc fc fc fc fc fc fc >c00000001d1d0100: fc fc fc 02 fc fc fc fc fc fc fc fc fc fc fc fc ^ c00000001d1d0180: fc fc fc fc 04 fc fc fc fc fc fc fc fc fc fc fc c00000001d1d0200: fc fc fc fc fc 04 fc fc fc fc fc fc fc fc fc fc This happens because the allocation uses the wrong unit (bits) when it should pass (BITS_TO_LONGS(count) * sizeof(long)) or equivalent. With small numbers of bits, the allocated object can be smaller than sizeof(long), which results in invalid accesses. Use bitmap_zalloc() to allocate and initialize the irq bitmap, paired with bitmap_free() for consistency.

In the Linux kernel, the following vulnerability has been resolved: usb: isp1760: Fix out-of-bounds array access Running the driver through kasan gives an interesting splat: BUG: KASAN: global-out-of-bounds in isp1760_register+0x180/0x70c Read of size 20 at addr f1db2e64 by task swapper/0/1 (...) isp1760_register from isp1760_plat_probe+0x1d8/0x220 (...) This happens because the loop reading the regmap fields for the different ISP1760 variants look like this: for (i = 0; i < HC_FIELD_MAX; i++) { ... } Meaning it expects the arrays to be at least HC_FIELD_MAX - 1 long. However the arrays isp1760_hc_reg_fields[], isp1763_hc_reg_fields[], isp1763_hc_volatile_ranges[] and isp1763_dc_volatile_ranges[] are dynamically sized during compilation. Fix this by putting an empty assignment to the [HC_FIELD_MAX] and [DC_FIELD_MAX] array member at the end of each array. This will make the array one member longer than it needs to be, but avoids the risk of overwriting whatever is inside [HC_FIELD_MAX - 1] and is simple and intuitive to read. Also add comments explaining what is going on.

In the Linux kernel, the following vulnerability has been resolved: ACPI: CPPC: Avoid out of bounds access when parsing _CPC data If the NumEntries field in the _CPC return package is less than 2, do not attempt to access the "Revision" element of that package, because it may not be present then. BugLink: https://lore.kernel.org/lkml/20220322143534.GC32582@xsang-OptiPlex-9020/

In the Linux kernel, the following vulnerability has been resolved: drm/dp: Fix OOB read when handling Post Cursor2 register The link_status array was not large enough to read the Adjust Request Post Cursor2 register, so remove the common helper function to avoid an OOB read, found with a -Warray-bounds build: drivers/gpu/drm/drm_dp_helper.c: In function 'drm_dp_get_adjust_request_post_cursor': drivers/gpu/drm/drm_dp_helper.c:59:27: error: array subscript 10 is outside array bounds of 'const u8[6]' {aka 'const unsigned char[6]'} [-Werror=array-bounds] 59 | return link_status[r - DP_LANE0_1_STATUS]; | ~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~ drivers/gpu/drm/drm_dp_helper.c:147:51: note: while referencing 'link_status' 147 | u8 drm_dp_get_adjust_request_post_cursor(const u8 link_status[DP_LINK_STATUS_SIZE], | ~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Replace the only user of the helper with an open-coded fetch and decode, similar to drivers/gpu/drm/amd/display/dc/core/dc_link_dp.c.

In the Linux kernel, the following vulnerability has been resolved: dm raid: fix accesses beyond end of raid member array On dm-raid table load (using raid_ctr), dm-raid allocates an array rs->devs[rs->raid_disks] for the raid device members. rs->raid_disks is defined by the number of raid metadata and image tupples passed into the target's constructor. In the case of RAID layout changes being requested, that number can be different from the current number of members for existing raid sets as defined in their superblocks. Example RAID layout changes include: - raid1 legs being added/removed - raid4/5/6/10 number of stripes changed (stripe reshaping) - takeover to higher raid level (e.g. raid5 -> raid6) When accessing array members, rs->raid_disks must be used in control loops instead of the potentially larger value in rs->md.raid_disks. Otherwise it will cause memory access beyond the end of the rs->devs array. Fix this by changing code that is prone to out-of-bounds access. Also fix validate_raid_redundancy() to validate all devices that are added. Also, use braces to help clean up raid_iterate_devices(). The out-of-bounds memory accesses was discovered using KASAN. This commit was verified to pass all LVM2 RAID tests (with KASAN enabled).

In the Linux kernel, the following vulnerability has been resolved: net: dsa: Avoid cross-chip syncing of VLAN filtering Changes to VLAN filtering are not applicable to cross-chip notifications. On a system like this: .-----. .-----. .-----. | sw1 +---+ sw2 +---+ sw3 | '-1-2-' '-1-2-' '-1-2-' Before this change, upon sw1p1 leaving a bridge, a call to dsa_port_vlan_filtering would also be made to sw2p1 and sw3p1. In this scenario: .---------. .-----. .-----. | sw1 +---+ sw2 +---+ sw3 | '-1-2-3-4-' '-1-2-' '-1-2-' When sw1p4 would leave a bridge, dsa_port_vlan_filtering would be called for sw2 and sw3 with a non-existing port - leading to array out-of-bounds accesses and crashes on mv88e6xxx.

In the Linux kernel, the following vulnerability has been resolved: module: fix [e_shstrndx].sh_size=0 OOB access It is trivial to craft a module to trigger OOB access in this line: if (info->secstrings[strhdr->sh_size - 1] != '\0') { BUG: unable to handle page fault for address: ffffc90000aa0fff PGD 100000067 P4D 100000067 PUD 100066067 PMD 10436f067 PTE 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 7 PID: 1215 Comm: insmod Not tainted 5.18.0-rc5-00007-g9bf578647087-dirty #10 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-4.fc34 04/01/2014 RIP: 0010:load_module+0x19b/0x2391 [rebased patch onto modules-next]

In the Linux kernel, the following vulnerability has been resolved: NFSD: Fix the behavior of READ near OFFSET_MAX Dan Aloni reports: > Due to commit 8cfb9015280d ("NFS: Always provide aligned buffers to > the RPC read layers") on the client, a read of 0xfff is aligned up > to server rsize of 0x1000. > > As a result, in a test where the server has a file of size > 0x7fffffffffffffff, and the client tries to read from the offset > 0x7ffffffffffff000, the read causes loff_t overflow in the server > and it returns an NFS code of EINVAL to the client. The client as > a result indefinitely retries the request. The Linux NFS client does not handle NFS?ERR_INVAL, even though all NFS specifications permit servers to return that status code for a READ. Instead of NFS?ERR_INVAL, have out-of-range READ requests succeed and return a short result. Set the EOF flag in the result to prevent the client from retrying the READ request. This behavior appears to be consistent with Solaris NFS servers. Note that NFSv3 and NFSv4 use u64 offset values on the wire. These must be converted to loff_t internally before use -- an implicit type cast is not adequate for this purpose. Otherwise VFS checks against sb->s_maxbytes do not work properly.

In the Linux kernel, the following vulnerability has been resolved: ASoC: codecs: rx-macro: fix accessing array out of bounds for enum type Accessing enums using integer would result in array out of bounds access on platforms like aarch64 where sizeof(long) is 8 compared to enum size which is 4 bytes.

In the Linux kernel, the following vulnerability has been resolved: net: mvneta: Prevent out of bounds read in mvneta_config_rss() The pp->indir[0] value comes from the user. It is passed to: if (cpu_online(pp->rxq_def)) inside the mvneta_percpu_elect() function. It needs bounds checkeding to ensure that it is not beyond the end of the cpu bitmap.

In the Linux kernel, the following vulnerability has been resolved: iio: health: afe4404: Fix oob read in afe4404_[read|write]_raw KASAN report out-of-bounds read as follows: BUG: KASAN: global-out-of-bounds in afe4404_read_raw+0x2ce/0x380 Read of size 4 at addr ffffffffc00e4658 by task cat/278 Call Trace: afe4404_read_raw iio_read_channel_info dev_attr_show The buggy address belongs to the variable: afe4404_channel_leds+0x18/0xffffffffffffe9c0 This issue can be reproduce by singe command: $ cat /sys/bus/i2c/devices/0-0058/iio\:device0/in_intensity6_raw The array size of afe4404_channel_leds and afe4404_channel_offdacs are less than channels, so access with chan->address cause OOB read in afe4404_[read|write]_raw. Fix it by moving access before use them.

In the Linux kernel, the following vulnerability has been resolved: net/tls: fix slab-out-of-bounds bug in decrypt_internal The memory size of tls_ctx->rx.iv for AES128-CCM is 12 setting in tls_set_sw_offload(). The return value of crypto_aead_ivsize() for "ccm(aes)" is 16. So memcpy() require 16 bytes from 12 bytes memory space will trigger slab-out-of-bounds bug as following: ================================================================== BUG: KASAN: slab-out-of-bounds in decrypt_internal+0x385/0xc40 [tls] Read of size 16 at addr ffff888114e84e60 by task tls/10911 Call Trace: <TASK> dump_stack_lvl+0x34/0x44 print_report.cold+0x5e/0x5db ? decrypt_internal+0x385/0xc40 [tls] kasan_report+0xab/0x120 ? decrypt_internal+0x385/0xc40 [tls] kasan_check_range+0xf9/0x1e0 memcpy+0x20/0x60 decrypt_internal+0x385/0xc40 [tls] ? tls_get_rec+0x2e0/0x2e0 [tls] ? process_rx_list+0x1a5/0x420 [tls] ? tls_setup_from_iter.constprop.0+0x2e0/0x2e0 [tls] decrypt_skb_update+0x9d/0x400 [tls] tls_sw_recvmsg+0x3c8/0xb50 [tls] Allocated by task 10911: kasan_save_stack+0x1e/0x40 __kasan_kmalloc+0x81/0xa0 tls_set_sw_offload+0x2eb/0xa20 [tls] tls_setsockopt+0x68c/0x700 [tls] __sys_setsockopt+0xfe/0x1b0 Replace the crypto_aead_ivsize() with prot->iv_size + prot->salt_size when memcpy() iv value in TLS_1_3_VERSION scenario.

In the Linux kernel, the following vulnerability has been resolved: ASoC: codecs: va-macro: fix accessing array out of bounds for enum type Accessing enums using integer would result in array out of bounds access on platforms like aarch64 where sizeof(long) is 8 compared to enum size which is 4 bytes.

In the Linux kernel, the following vulnerability has been resolved: mm/page_owner: use strscpy() instead of strlcpy() current->comm[] is not a string (no guarantee for a zero byte in it). strlcpy(s1, s2, l) is calling strlen(s2), potentially causing out-of-bound access, as reported by syzbot: detected buffer overflow in __fortify_strlen ------------[ cut here ]------------ kernel BUG at lib/string_helpers.c:980! invalid opcode: 0000 [#1] PREEMPT SMP KASAN CPU: 0 PID: 4087 Comm: dhcpcd-run-hooks Not tainted 5.18.0-rc3-syzkaller-01537-g20b87e7c29df #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:fortify_panic+0x18/0x1a lib/string_helpers.c:980 Code: 8c e8 c5 ba e1 fa e9 23 0f bf fa e8 0b 5d 8c f8 eb db 55 48 89 fd e8 e0 49 40 f8 48 89 ee 48 c7 c7 80 f5 26 8a e8 99 09 f1 ff <0f> 0b e8 ca 49 40 f8 48 8b 54 24 18 4c 89 f1 48 c7 c7 00 00 27 8a RSP: 0018:ffffc900000074a8 EFLAGS: 00010286 RAX: 000000000000002c RBX: ffff88801226b728 RCX: 0000000000000000 RDX: ffff8880198e0000 RSI: ffffffff81600458 RDI: fffff52000000e87 RBP: ffffffff89da2aa0 R08: 000000000000002c R09: 0000000000000000 R10: ffffffff815fae2e R11: 0000000000000000 R12: ffff88801226b700 R13: ffff8880198e0830 R14: 0000000000000000 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff8880b9c00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f5876ad6ff8 CR3: 000000001a48c000 CR4: 00000000003506f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000600 Call Trace: <IRQ> __fortify_strlen include/linux/fortify-string.h:128 [inline] strlcpy include/linux/fortify-string.h:143 [inline] __set_page_owner_handle+0x2b1/0x3e0 mm/page_owner.c:171 __set_page_owner+0x3e/0x50 mm/page_owner.c:190 prep_new_page mm/page_alloc.c:2441 [inline] get_page_from_freelist+0xba2/0x3e00 mm/page_alloc.c:4182 __alloc_pages+0x1b2/0x500 mm/page_alloc.c:5408 alloc_pages+0x1aa/0x310 mm/mempolicy.c:2272 alloc_slab_page mm/slub.c:1799 [inline] allocate_slab+0x26c/0x3c0 mm/slub.c:1944 new_slab mm/slub.c:2004 [inline] ___slab_alloc+0x8df/0xf20 mm/slub.c:3005 __slab_alloc.constprop.0+0x4d/0xa0 mm/slub.c:3092 slab_alloc_node mm/slub.c:3183 [inline] slab_alloc mm/slub.c:3225 [inline] __kmem_cache_alloc_lru mm/slub.c:3232 [inline] kmem_cache_alloc+0x360/0x3b0 mm/slub.c:3242 dst_alloc+0x146/0x1f0 net/core/dst.c:92

In the Linux kernel, the following vulnerability has been resolved: uaccess: fix integer overflow on access_ok() Three architectures check the end of a user access against the address limit without taking a possible overflow into account. Passing a negative length or another overflow in here returns success when it should not. Use the most common correct implementation here, which optimizes for a constant 'size' argument, and turns the common case into a single comparison.

In the Linux kernel, the following vulnerability has been resolved: ASoC: SOF: ipc3-topology: Correct get_control_data for non bytes payload It is possible to craft a topology where sof_get_control_data() would do out of bounds access because it expects that it is only called when the payload is bytes type. Confusingly it also handles other types of controls, but the payload parsing implementation is only valid for bytes. Fix the code to count the non bytes controls and instead of storing a pointer to sof_abi_hdr in sof_widget_data (which is only valid for bytes), store the pointer to the data itself and add a new member to save the size of the data. In case of non bytes controls we store the pointer to the chanv itself, which is just an array of values at the end. In case of bytes control, drop the wrong cdata->data (wdata[i].pdata) check against NULL since it is incorrect and invalid in this context. The data is pointing to the end of cdata struct, so it should never be null.