In the Linux kernel, the following vulnerability has been resolved: RDMA/hns: Fix NULL pointer derefernce in hns_roce_map_mr_sg() ib_map_mr_sg() allows ULPs to specify NULL as the sg_offset argument. The driver needs to check whether it is a NULL pointer before dereferencing it.

In the Linux kernel, the following vulnerability has been resolved: net: lan966x: fix page_pool error handling in lan966x_fdma_rx_alloc_page_pool() page_pool_create() can return an ERR_PTR on failure. The return value is used unconditionally in the loop that follows, passing the error pointer through xdp_rxq_info_reg_mem_model() into page_pool_use_xdp_mem(), which dereferences it, causing a kernel oops. Add an IS_ERR check after page_pool_create() to return early on failure.

In the Linux kernel, the following vulnerability has been resolved: mm/damon/sysfs: check contexts->nr before accessing contexts_arr[0] Multiple sysfs command paths dereference contexts_arr[0] without first verifying that kdamond->contexts->nr == 1. A user can set nr_contexts to 0 via sysfs while DAMON is running, causing NULL pointer dereferences. In more detail, the issue can be triggered by privileged users like below. First, start DAMON and make contexts directory empty (kdamond->contexts->nr == 0). # damo start # cd /sys/kernel/mm/damon/admin/kdamonds/0 # echo 0 > contexts/nr_contexts Then, each of below commands will cause the NULL pointer dereference. # echo update_schemes_stats > state # echo update_schemes_tried_regions > state # echo update_schemes_tried_bytes > state # echo update_schemes_effective_quotas > state # echo update_tuned_intervals > state Guard all commands (except OFF) at the entry point of damon_sysfs_handle_cmd().

In the Linux kernel, the following vulnerability has been resolved: tracing: Drain deferred trigger frees if kthread creation fails Boot-time trigger registration can fail before the trigger-data cleanup kthread exists. Deferring those frees until late init is fine, but the post-boot fallback must still drain the deferred list if kthread creation never succeeds. Otherwise, boot-deferred nodes can accumulate on trigger_data_free_list, later frees fall back to synchronously freeing only the current object, and the older queued entries are leaked forever. To trigger this, add the following to the kernel command line: trace_event=sched_switch trace_trigger=sched_switch.traceon,sched_switch.traceon The second traceon trigger will fail and be freed. This triggers a NULL pointer dereference and crashes the kernel. Keep the deferred boot-time behavior, but when kthread creation fails, drain the whole queued list synchronously. Do the same in the late-init drain path so queued entries are not stranded there either.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Check null pointers before using them [WHAT & HOW] These pointers are null checked previously in the same function, indicating they might be null as reported by Coverity. As a result, they need to be checked when used again. This fixes 3 FORWARD_NULL issue reported by Coverity.

In the Linux kernel, the following vulnerability has been resolved: octeon_ep: Add SKB allocation failures handling in __octep_oq_process_rx() build_skb() returns NULL in case of a memory allocation failure so handle it inside __octep_oq_process_rx() to avoid NULL pointer dereference. __octep_oq_process_rx() is called during NAPI polling by the driver. If skb allocation fails, keep on pulling packets out of the Rx DMA queue: we shouldn't break the polling immediately and thus falsely indicate to the octep_napi_poll() that the Rx pressure is going down. As there is no associated skb in this case, don't process the packets and don't push them up the network stack - they are skipped. Helper function is implemented to unmmap/flush all the fragment buffers used by the dropped packet. 'alloc_failures' counter is incremented to mark the skb allocation error in driver statistics. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Add null check for 'afb' in amdgpu_dm_update_cursor (v2) This commit adds a null check for the 'afb' variable in the amdgpu_dm_update_cursor function. Previously, 'afb' was assumed to be null at line 8388, but was used later in the code without a null check. This could potentially lead to a null pointer dereference. Changes since v1: - Moved the null check for 'afb' to the line where 'afb' is used. (Alex) Fixes the below: drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:8433 amdgpu_dm_update_cursor() error: we previously assumed 'afb' could be null (see line 8388)

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Add NULL check for function pointer in dcn20_set_output_transfer_func This commit adds a null check for the set_output_gamma function pointer in the dcn20_set_output_transfer_func function. Previously, set_output_gamma was being checked for null at line 1030, but then it was being dereferenced without any null check at line 1048. This could potentially lead to a null pointer dereference error if set_output_gamma is null. To fix this, we now ensure that set_output_gamma is not null before dereferencing it. We do this by adding a null check for set_output_gamma before the call to set_output_gamma at line 1048.

In the Linux kernel, the following vulnerability has been resolved: btrfs: set BTRFS_ROOT_ORPHAN_CLEANUP during subvol create We have recently observed a number of subvolumes with broken dentries. ls-ing the parent dir looks like: drwxrwxrwt 1 root root 16 Jan 23 16:49 . drwxr-xr-x 1 root root 24 Jan 23 16:48 .. d????????? ? ? ? ? ? broken_subvol and similarly stat-ing the file fails. In this state, deleting the subvol fails with ENOENT, but attempting to create a new file or subvol over it errors out with EEXIST and even aborts the fs. Which leaves us a bit stuck. dmesg contains a single notable error message reading: "could not do orphan cleanup -2" 2 is ENOENT and the error comes from the failure handling path of btrfs_orphan_cleanup(), with the stack leading back up to btrfs_lookup(). btrfs_lookup btrfs_lookup_dentry btrfs_orphan_cleanup // prints that message and returns -ENOENT After some detailed inspection of the internal state, it became clear that: - there are no orphan items for the subvol - the subvol is otherwise healthy looking, it is not half-deleted or anything, there is no drop progress, etc. - the subvol was created a while ago and does the meaningful first btrfs_orphan_cleanup() call that sets BTRFS_ROOT_ORPHAN_CLEANUP much later. - after btrfs_orphan_cleanup() fails, btrfs_lookup_dentry() returns -ENOENT, which results in a negative dentry for the subvolume via d_splice_alias(NULL, dentry), leading to the observed behavior. The bug can be mitigated by dropping the dentry cache, at which point we can successfully delete the subvolume if we want. i.e., btrfs_lookup() btrfs_lookup_dentry() if (!sb_rdonly(inode->vfs_inode)->vfs_inode) btrfs_orphan_cleanup(sub_root) test_and_set_bit(BTRFS_ROOT_ORPHAN_CLEANUP) btrfs_search_slot() // finds orphan item for inode N ... prints "could not do orphan cleanup -2" if (inode == ERR_PTR(-ENOENT)) inode = NULL; return d_splice_alias(NULL, dentry) // NEGATIVE DENTRY for valid subvolume btrfs_orphan_cleanup() does test_and_set_bit(BTRFS_ROOT_ORPHAN_CLEANUP) on the root when it runs, so it cannot run more than once on a given root, so something else must run concurrently. However, the obvious routes to deleting an orphan when nlinks goes to 0 should not be able to run without first doing a lookup into the subvolume, which should run btrfs_orphan_cleanup() and set the bit. The final important observation is that create_subvol() calls d_instantiate_new() but does not set BTRFS_ROOT_ORPHAN_CLEANUP, so if the dentry cache gets dropped, the next lookup into the subvolume will make a real call into btrfs_orphan_cleanup() for the first time. This opens up the possibility of concurrently deleting the inode/orphan items but most typical evict() paths will be holding a reference on the parent dentry (child dentry holds parent->d_lockref.count via dget in d_alloc(), released in __dentry_kill()) and prevent the parent from being removed from the dentry cache. The one exception is delayed iputs. Ordered extent creation calls igrab() on the inode. If the file is unlinked and closed while those refs are held, iput() in __dentry_kill() decrements i_count but does not trigger eviction (i_count > 0). The child dentry is freed and the subvol dentry's d_lockref.count drops to 0, making it evictable while the inode is still alive. Since there are two races (the race between writeback and unlink and the race between lookup and delayed iputs), and there are too many moving parts, the following three diagrams show the complete picture. (Only the second and third are races) Phase 1: Create Subvol in dentry cache without BTRFS_ROOT_ORPHAN_CLEANUP set btrfs_mksubvol() lookup_one_len() __lookup_slow() d_alloc_parallel() __d_alloc() // d_lockref.count = 1 create_subvol(dentry) // doesn't touch the bit.. d_instantiate_new(dentry, inode) // dentry in cache with d_lockref.c ---truncated---

In the Linux kernel, the following vulnerability has been resolved: HID: alps: fix NULL pointer dereference in alps_raw_event() Commit ecfa6f34492c ("HID: Add HID_CLAIMED_INPUT guards in raw_event callbacks missing them") attempted to fix up the HID drivers that had missed the previous fix that was done in 2ff5baa9b527 ("HID: appleir: Fix potential NULL dereference at raw event handle"), but the alps driver was missed. Fix this up by properly checking in the hid-alps driver that it had been claimed correctly before attempting to process the raw event.

In the Linux kernel, the following vulnerability has been resolved: ASoC: qcom: sc7280: Fix missing Soundwire runtime stream alloc Commit 15c7fab0e047 ("ASoC: qcom: Move Soundwire runtime stream alloc to soundcards") moved the allocation of Soundwire stream runtime from the Qualcomm Soundwire driver to each individual machine sound card driver, except that it forgot to update SC7280 card. Just like for other Qualcomm sound cards using Soundwire, the card driver should allocate and release the runtime. Otherwise sound playback will result in a NULL pointer dereference or other effect of uninitialized memory accesses (which was confirmed on SDM845 having similar issue).

In the Linux kernel, the following vulnerability has been resolved: cpufreq: amd-pstate: add check for cpufreq_cpu_get's return value cpufreq_cpu_get may return NULL. To avoid NULL-dereference check it and return in case of error. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix a NULL pointer dereference when failed to start a new trasacntion [BUG] Syzbot reported a NULL pointer dereference with the following crash: FAULT_INJECTION: forcing a failure. start_transaction+0x830/0x1670 fs/btrfs/transaction.c:676 prepare_to_relocate+0x31f/0x4c0 fs/btrfs/relocation.c:3642 relocate_block_group+0x169/0xd20 fs/btrfs/relocation.c:3678 ... BTRFS info (device loop0): balance: ended with status: -12 Oops: general protection fault, probably for non-canonical address 0xdffffc00000000cc: 0000 [#1] PREEMPT SMP KASAN NOPTI KASAN: null-ptr-deref in range [0x0000000000000660-0x0000000000000667] RIP: 0010:btrfs_update_reloc_root+0x362/0xa80 fs/btrfs/relocation.c:926 Call Trace: <TASK> commit_fs_roots+0x2ee/0x720 fs/btrfs/transaction.c:1496 btrfs_commit_transaction+0xfaf/0x3740 fs/btrfs/transaction.c:2430 del_balance_item fs/btrfs/volumes.c:3678 [inline] reset_balance_state+0x25e/0x3c0 fs/btrfs/volumes.c:3742 btrfs_balance+0xead/0x10c0 fs/btrfs/volumes.c:4574 btrfs_ioctl_balance+0x493/0x7c0 fs/btrfs/ioctl.c:3673 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:907 [inline] __se_sys_ioctl+0xf9/0x170 fs/ioctl.c:893 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f [CAUSE] The allocation failure happens at the start_transaction() inside prepare_to_relocate(), and during the error handling we call unset_reloc_control(), which makes fs_info->balance_ctl to be NULL. Then we continue the error path cleanup in btrfs_balance() by calling reset_balance_state() which will call del_balance_item() to fully delete the balance item in the root tree. However during the small window between set_reloc_contrl() and unset_reloc_control(), we can have a subvolume tree update and created a reloc_root for that subvolume. Then we go into the final btrfs_commit_transaction() of del_balance_item(), and into btrfs_update_reloc_root() inside commit_fs_roots(). That function checks if fs_info->reloc_ctl is in the merge_reloc_tree stage, but since fs_info->reloc_ctl is NULL, it results a NULL pointer dereference. [FIX] Just add extra check on fs_info->reloc_ctl inside btrfs_update_reloc_root(), before checking fs_info->reloc_ctl->merge_reloc_tree. That DEAD_RELOC_TREE handling is to prevent further modification to the reloc tree during merge stage, but since there is no reloc_ctl at all, we do not need to bother that.

In the Linux kernel, the following vulnerability has been resolved: drm/mediatek: dsi: Store driver data before invoking mipi_dsi_host_register The call to mipi_dsi_host_register triggers a callback to mtk_dsi_bind, which uses dev_get_drvdata to retrieve the mtk_dsi struct, so this structure needs to be stored inside the driver data before invoking it. As drvdata is currently uninitialized it leads to a crash when registering the DSI DRM encoder right after acquiring the mode_config.idr_mutex, blocking all subsequent DRM operations. Fixes the following crash during mediatek-drm probe (tested on Xiaomi Smart Clock x04g): Unable to handle kernel NULL pointer dereference at virtual address 0000000000000040 [...] Modules linked in: mediatek_drm(+) drm_display_helper cec drm_client_lib drm_dma_helper drm_kms_helper panel_simple [...] Call trace: drm_mode_object_add+0x58/0x98 (P) __drm_encoder_init+0x48/0x140 drm_encoder_init+0x6c/0xa0 drm_simple_encoder_init+0x20/0x34 [drm_kms_helper] mtk_dsi_bind+0x34/0x13c [mediatek_drm] component_bind_all+0x120/0x280 mtk_drm_bind+0x284/0x67c [mediatek_drm] try_to_bring_up_aggregate_device+0x23c/0x320 __component_add+0xa4/0x198 component_add+0x14/0x20 mtk_dsi_host_attach+0x78/0x100 [mediatek_drm] mipi_dsi_attach+0x2c/0x50 panel_simple_dsi_probe+0x4c/0x9c [panel_simple] mipi_dsi_drv_probe+0x1c/0x28 really_probe+0xc0/0x3dc __driver_probe_device+0x80/0x160 driver_probe_device+0x40/0x120 __device_attach_driver+0xbc/0x17c bus_for_each_drv+0x88/0xf0 __device_attach+0x9c/0x1cc device_initial_probe+0x54/0x60 bus_probe_device+0x34/0xa0 device_add+0x5b0/0x800 mipi_dsi_device_register_full+0xdc/0x16c mipi_dsi_host_register+0xc4/0x17c mtk_dsi_probe+0x10c/0x260 [mediatek_drm] platform_probe+0x5c/0xa4 really_probe+0xc0/0x3dc __driver_probe_device+0x80/0x160 driver_probe_device+0x40/0x120 __driver_attach+0xc8/0x1f8 bus_for_each_dev+0x7c/0xe0 driver_attach+0x24/0x30 bus_add_driver+0x11c/0x240 driver_register+0x68/0x130 __platform_register_drivers+0x64/0x160 mtk_drm_init+0x24/0x1000 [mediatek_drm] do_one_initcall+0x60/0x1d0 do_init_module+0x54/0x240 load_module+0x1838/0x1dc0 init_module_from_file+0xd8/0xf0 __arm64_sys_finit_module+0x1b4/0x428 invoke_syscall.constprop.0+0x48/0xc8 do_el0_svc+0x3c/0xb8 el0_svc+0x34/0xe8 el0t_64_sync_handler+0xa0/0xe4 el0t_64_sync+0x198/0x19c Code: 52800022 941004ab 2a0003f3 37f80040 (29005a80)

In the Linux kernel, the following vulnerability has been resolved: dlm: fix possible lkb_resource null dereference This patch fixes a possible null pointer dereference when this function is called from request_lock() as lkb->lkb_resource is not assigned yet, only after validate_lock_args() by calling attach_lkb(). Another issue is that a resource name could be a non printable bytearray and we cannot assume to be ASCII coded. The log functionality is probably never being hit when DLM is used in normal way and no debug logging is enabled. The null pointer dereference can only occur on a new created lkb that does not have the resource assigned yet, it probably never hits the null pointer dereference but we should be sure that other changes might not change this behaviour and we actually can hit the mentioned null pointer dereference. In this patch we just drop the printout of the resource name, the lkb id is enough to make a possible connection to a resource name if this exists.

In the Linux kernel, the following vulnerability has been resolved: net: bonding: fix NULL deref in bond_debug_rlb_hash_show rlb_clear_slave intentionally keeps RLB hash-table entries on the rx_hashtbl_used_head list with slave set to NULL when no replacement slave is available. However, bond_debug_rlb_hash_show visites client_info->slave without checking if it's NULL. Other used-list iterators in bond_alb.c already handle this NULL-slave state safely: - rlb_update_client returns early on !client_info->slave - rlb_req_update_slave_clients, rlb_clear_slave, and rlb_rebalance compare slave values before visiting - lb_req_update_subnet_clients continues if slave is NULL The following NULL deref crash can be trigger in bond_debug_rlb_hash_show: [ 1.289791] BUG: kernel NULL pointer dereference, address: 0000000000000000 [ 1.292058] RIP: 0010:bond_debug_rlb_hash_show (drivers/net/bonding/bond_debugfs.c:41) [ 1.293101] RSP: 0018:ffffc900004a7d00 EFLAGS: 00010286 [ 1.293333] RAX: 0000000000000000 RBX: ffff888102b48200 RCX: ffff888102b48204 [ 1.293631] RDX: ffff888102b48200 RSI: ffffffff839daad5 RDI: ffff888102815078 [ 1.293924] RBP: ffff888102815078 R08: ffff888102b4820e R09: 0000000000000000 [ 1.294267] R10: 0000000000000000 R11: 0000000000000000 R12: ffff888100f929c0 [ 1.294564] R13: ffff888100f92a00 R14: 0000000000000001 R15: ffffc900004a7ed8 [ 1.294864] FS: 0000000001395380(0000) GS:ffff888196e75000(0000) knlGS:0000000000000000 [ 1.295239] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1.295480] CR2: 0000000000000000 CR3: 0000000102adc004 CR4: 0000000000772ef0 [ 1.295897] Call Trace: [ 1.296134] seq_read_iter (fs/seq_file.c:231) [ 1.296341] seq_read (fs/seq_file.c:164) [ 1.296493] full_proxy_read (fs/debugfs/file.c:378 (discriminator 1)) [ 1.296658] vfs_read (fs/read_write.c:572) [ 1.296981] ksys_read (fs/read_write.c:717) [ 1.297132] do_syscall_64 (arch/x86/entry/syscall_64.c:63 (discriminator 1) arch/x86/entry/syscall_64.c:94 (discriminator 1)) [ 1.297325] entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130) Add a NULL check and print "(none)" for entries with no assigned slave.

In the Linux kernel, the following vulnerability has been resolved: netfs: Fix kernel BUG in netfs_limit_iter() for ITER_KVEC iterators When a process crashes and the kernel writes a core dump to a 9P filesystem, __kernel_write() creates an ITER_KVEC iterator. This iterator reaches netfs_limit_iter() via netfs_unbuffered_write(), which only handles ITER_FOLIOQ, ITER_BVEC and ITER_XARRAY iterator types, hitting the BUG() for any other type. Fix this by adding netfs_limit_kvec() following the same pattern as netfs_limit_bvec(), since both kvec and bvec are simple segment arrays with pointer and length fields. Dispatch it from netfs_limit_iter() when the iterator type is ITER_KVEC.

In the Linux kernel, the following vulnerability has been resolved: mmc: vub300: fix NULL-deref on disconnect Make sure to deregister the controller before dropping the reference to the driver data on disconnect to avoid NULL-pointer dereferences or use-after-free.

In the Linux kernel, the following vulnerability has been resolved: LoongArch: Fix missing NULL checks for kstrdup() 1. Replace "of_find_node_by_path("/")" with "of_root" to avoid multiple calls to "of_node_put()". 2. Fix a potential kernel oops during early boot when memory allocation fails while parsing CPU model from device tree.

In the Linux kernel, the following vulnerability has been resolved: i2c: cp2615: fix serial string NULL-deref at probe The cp2615 driver uses the USB device serial string as the i2c adapter name but does not make sure that the string exists. Verify that the device has a serial number before accessing it to avoid triggering a NULL-pointer dereference (e.g. with malicious devices).

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: renesas_usb3: validate endpoint index in standard request handlers The GET_STATUS and SET/CLEAR_FEATURE handlers extract the endpoint number from the host-supplied wIndex without any sort of validation. Fix this up by validating the number of endpoints actually match up with the number the device has before attempting to dereference a pointer based on this math. This is just like what was done in commit ee0d382feb44 ("usb: gadget: aspeed_udc: validate endpoint index for ast udc") for the aspeed driver.

In the Linux kernel, the following vulnerability has been resolved: EDAC/mc: Fix error path ordering in edac_mc_alloc() When the mci->pvt_info allocation in edac_mc_alloc() fails, the error path will call put_device() which will end up calling the device's release function. However, the init ordering is wrong such that device_initialize() happens *after* the failed allocation and thus the device itself and the release function pointer are not initialized yet when they're called: MCE: In-kernel MCE decoding enabled. ------------[ cut here ]------------ kobject: '(null)': is not initialized, yet kobject_put() is being called. WARNING: lib/kobject.c:734 at kobject_put, CPU#22: systemd-udevd CPU: 22 UID: 0 PID: 538 Comm: systemd-udevd Not tainted 7.0.0-rc1+ #2 PREEMPT(full) RIP: 0010:kobject_put Call Trace: <TASK> edac_mc_alloc+0xbe/0xe0 [edac_core] amd64_edac_init+0x7a4/0xff0 [amd64_edac] ? __pfx_amd64_edac_init+0x10/0x10 [amd64_edac] do_one_initcall ... Reorder the calling sequence so that the device is initialized and thus the release function pointer is properly set before it can be used. This was found by Claude while reviewing another EDAC patch.

In the Linux kernel, the following vulnerability has been resolved: bcache: revert replacing IS_ERR_OR_NULL with IS_ERR again Commit 028ddcac477b ("bcache: Remove unnecessary NULL point check in node allocations") leads a NULL pointer deference in cache_set_flush(). 1721 if (!IS_ERR_OR_NULL(c->root)) 1722 list_add(&c->root->list, &c->btree_cache); >From the above code in cache_set_flush(), if previous registration code fails before allocating c->root, it is possible c->root is NULL as what it is initialized. __bch_btree_node_alloc() never returns NULL but c->root is possible to be NULL at above line 1721. This patch replaces IS_ERR() by IS_ERR_OR_NULL() to fix this.

In the Linux kernel, the following vulnerability has been resolved: RDMA/cxgb4: Added NULL check for lookup_atid The lookup_atid() function can return NULL if the ATID is invalid or does not exist in the identifier table, which could lead to dereferencing a null pointer without a check in the `act_establish()` and `act_open_rpl()` functions. Add a NULL check to prevent null pointer dereferencing. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: media: coda: Add check for dcoda_iram_alloc As the coda_iram_alloc may return NULL pointer, it should be better to check the return value in order to avoid NULL poineter dereference, same as the others.

In the Linux kernel, the following vulnerability has been resolved: soundwire: revisit driver bind/unbind and callbacks In the SoundWire probe, we store a pointer from the driver ops into the 'slave' structure. This can lead to kernel oopses when unbinding codec drivers, e.g. with the following sequence to remove machine driver and codec driver. /sbin/modprobe -r snd_soc_sof_sdw /sbin/modprobe -r snd_soc_rt711 The full details can be found in the BugLink below, for reference the two following examples show different cases of driver ops/callbacks being invoked after the driver .remove(). kernel: BUG: kernel NULL pointer dereference, address: 0000000000000150 kernel: Workqueue: events cdns_update_slave_status_work [soundwire_cadence] kernel: RIP: 0010:mutex_lock+0x19/0x30 kernel: Call Trace: kernel: ? sdw_handle_slave_status+0x426/0xe00 [soundwire_bus 94ff184bf398570c3f8ff7efe9e32529f532e4ae] kernel: ? newidle_balance+0x26a/0x400 kernel: ? cdns_update_slave_status_work+0x1e9/0x200 [soundwire_cadence 1bcf98eebe5ba9833cd433323769ac923c9c6f82] kernel: BUG: unable to handle page fault for address: ffffffffc07654c8 kernel: Workqueue: pm pm_runtime_work kernel: RIP: 0010:sdw_bus_prep_clk_stop+0x6f/0x160 [soundwire_bus] kernel: Call Trace: kernel: <TASK> kernel: sdw_cdns_clock_stop+0xb5/0x1b0 [soundwire_cadence 1bcf98eebe5ba9833cd433323769ac923c9c6f82] kernel: intel_suspend_runtime+0x5f/0x120 [soundwire_intel aca858f7c87048d3152a4a41bb68abb9b663a1dd] kernel: ? dpm_sysfs_remove+0x60/0x60 This was not detected earlier in Intel tests since the tests first remove the parent PCI device and shut down the bus. The sequence above is a corner case which keeps the bus operational but without a driver bound. While trying to solve this kernel oopses, it became clear that the existing SoundWire bus does not deal well with the unbind case. Commit 528be501b7d4a ("soundwire: sdw_slave: add probe_complete structure and new fields") added a 'probed' status variable and a 'probe_complete' struct completion. This status is however not reset on remove and likewise the 'probe complete' is not re-initialized, so the bind/unbind/bind test cases would fail. The timeout used before the 'update_status' callback was also a bad idea in hindsight, there should really be no timing assumption as to if and when a driver is bound to a device. An initial draft was based on device_lock() and device_unlock() was tested. This proved too complicated, with deadlocks created during the suspend-resume sequences, which also use the same device_lock/unlock() as the bind/unbind sequences. On a CometLake device, a bad DSDT/BIOS caused spurious resumes and the use of device_lock() caused hangs during suspend. After multiple weeks or testing and painful reverse-engineering of deadlocks on different devices, we looked for alternatives that did not interfere with the device core. A bus notifier was used successfully to keep track of DRIVER_BOUND and DRIVER_UNBIND events. This solved the bind-unbind-bind case in tests, but it can still be defeated with a theoretical corner case where the memory is freed by a .remove while the callback is in use. The notifier only helps make sure the driver callbacks are valid, but not that the memory allocated in probe remains valid while the callbacks are invoked. This patch suggests the introduction of a new 'sdw_dev_lock' mutex protecting probe/remove and all driver callbacks. Since this mutex is 'local' to SoundWire only, it does not interfere with existing locks and does not create deadlocks. In addition, this patch removes the 'probe_complete' completion, instead we directly invoke the 'update_status' from the probe routine. That removes any sort of timing dependency and a much better support for the device/driver model, the driver could be bound before the bus started, or eons after the bus started and the hardware would be properly initialized in all cases. BugLink: https://github.com/thesofproject/linux/is ---truncated---

In the Linux kernel, the following vulnerability has been resolved: ASoC: qcom: Add checks for devm_kcalloc As the devm_kcalloc may return NULL, the return value needs to be checked to avoid NULL poineter dereference.

In the Linux kernel, the following vulnerability has been resolved: scsi: scsi_transport_sas: Fix error handling in sas_phy_add() If transport_add_device() fails in sas_phy_add(), the kernel will crash trying to delete the device in transport_remove_device() called from sas_remove_host(). Unable to handle kernel NULL pointer dereference at virtual address 0000000000000108 CPU: 61 PID: 42829 Comm: rmmod Kdump: loaded Tainted: G W 6.1.0-rc1+ #173 pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : device_del+0x54/0x3d0 lr : device_del+0x37c/0x3d0 Call trace: device_del+0x54/0x3d0 attribute_container_class_device_del+0x28/0x38 transport_remove_classdev+0x6c/0x80 attribute_container_device_trigger+0x108/0x110 transport_remove_device+0x28/0x38 sas_phy_delete+0x30/0x60 [scsi_transport_sas] do_sas_phy_delete+0x6c/0x80 [scsi_transport_sas] device_for_each_child+0x68/0xb0 sas_remove_children+0x40/0x50 [scsi_transport_sas] sas_remove_host+0x20/0x38 [scsi_transport_sas] hisi_sas_remove+0x40/0x68 [hisi_sas_main] hisi_sas_v2_remove+0x20/0x30 [hisi_sas_v2_hw] platform_remove+0x2c/0x60 Fix this by checking and handling return value of transport_add_device() in sas_phy_add().

In the Linux kernel, the following vulnerability has been resolved: net: lan966x: Fix potential null-ptr-deref in lan966x_stats_init() lan966x_stats_init() calls create_singlethread_workqueue() and not checked the ret value, which may return NULL. And a null-ptr-deref may happen: lan966x_stats_init() create_singlethread_workqueue() # failed, lan966x->stats_queue is NULL queue_delayed_work() queue_delayed_work_on() __queue_delayed_work() # warning here, but continue __queue_work() # access wq->flags, null-ptr-deref Check the ret value and return -ENOMEM if it is NULL.

In the Linux kernel, the following vulnerability has been resolved: bpftool: Fix NULL pointer dereference when pin {PROG, MAP, LINK} without FILE When using bpftool to pin {PROG, MAP, LINK} without FILE, segmentation fault will occur. The reson is that the lack of FILE will cause strlen to trigger NULL pointer dereference. The corresponding stacktrace is shown below: do_pin do_pin_any do_pin_fd mount_bpffs_for_pin strlen(name) <- NULL pointer dereference Fix it by adding validation to the common process.

In the Linux kernel, the following vulnerability has been resolved: xhci: Fix null pointer dereference in remove if xHC has only one roothub The remove path in xhci platform driver tries to remove and put both main and shared hcds even if only a main hcd exists (one roothub) This causes a null pointer dereference in reboot for those controllers. Check that the shared_hcd exists before trying to remove it.

In the Linux kernel, the following vulnerability has been resolved: kprobes: Fix check for probe enabled in kill_kprobe() In kill_kprobe(), the check whether disarm_kprobe_ftrace() needs to be called always fails. This is because before that we set the KPROBE_FLAG_GONE flag for kprobe so that "!kprobe_disabled(p)" is always false. The disarm_kprobe_ftrace() call introduced by commit: 0cb2f1372baa ("kprobes: Fix NULL pointer dereference at kprobe_ftrace_handler") to fix the NULL pointer reference problem. When the probe is enabled, if we do not disarm it, this problem still exists. Fix it by putting the probe enabled check before setting the KPROBE_FLAG_GONE flag.

In the Linux kernel, the following vulnerability has been resolved: locking/csd_lock: Change csdlock_debug from early_param to __setup The csdlock_debug kernel-boot parameter is parsed by the early_param() function csdlock_debug(). If set, csdlock_debug() invokes static_branch_enable() to enable csd_lock_wait feature, which triggers a panic on arm64 for kernels built with CONFIG_SPARSEMEM=y and CONFIG_SPARSEMEM_VMEMMAP=n. With CONFIG_SPARSEMEM_VMEMMAP=n, __nr_to_section is called in static_key_enable() and returns NULL, resulting in a NULL dereference because mem_section is initialized only later in sparse_init(). This is also a problem for powerpc because early_param() functions are invoked earlier than jump_label_init(), also resulting in static_key_enable() failures. These failures cause the warning "static key 'xxx' used before call to jump_label_init()". Thus, early_param is too early for csd_lock_wait to run static_branch_enable(), so changes it to __setup to fix these.

In the Linux kernel, the following vulnerability has been resolved: vdpa_sim_blk: set number of address spaces and virtqueue groups Commit bda324fd037a ("vdpasim: control virtqueue support") added two new fields (nas, ngroups) to vdpasim_dev_attr, but we forgot to initialize them for vdpa_sim_blk. When creating a new vdpa_sim_blk device this causes the kernel to panic in this way:    $ vdpa dev add mgmtdev vdpasim_blk name blk0    BUG: kernel NULL pointer dereference, address: 0000000000000030    ...    RIP: 0010:vhost_iotlb_add_range_ctx+0x41/0x220 [vhost_iotlb]    ...    Call Trace:     <TASK>     vhost_iotlb_add_range+0x11/0x800 [vhost_iotlb]     vdpasim_map_range+0x91/0xd0 [vdpa_sim]     vdpasim_alloc_coherent+0x56/0x90 [vdpa_sim]     ... This happens because vdpasim->iommu[0] is not initialized when dev_attr.nas is 0. Let's fix this issue by initializing both (nas, ngroups) to 1 for vdpa_sim_blk.

In the Linux kernel, the following vulnerability has been resolved: RDMA/rxe: Fix BUG: KASAN: null-ptr-deref in rxe_qp_do_cleanup The function rxe_create_qp calls rxe_qp_from_init. If some error occurs, the error handler of function rxe_qp_from_init will set both scq and rcq to NULL. Then rxe_create_qp calls rxe_put to handle qp. In the end, rxe_qp_do_cleanup is called by rxe_put. rxe_qp_do_cleanup directly accesses scq and rcq before checking them. This will cause null-ptr-deref error. The call graph is as below: rxe_create_qp { ... rxe_qp_from_init { ... err1: ... qp->rcq = NULL; <---rcq is set to NULL qp->scq = NULL; <---scq is set to NULL ... } qp_init: rxe_put{ ... rxe_qp_do_cleanup { ... atomic_dec(&qp->scq->num_wq); <--- scq is accessed ... atomic_dec(&qp->rcq->num_wq); <--- rcq is accessed } }

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: Don't finalize CSA in IBSS mode if state is disconnected When we are not connected to a channel, sending channel "switch" announcement doesn't make any sense. The BSS list is empty in that case. This causes the for loop in cfg80211_get_bss() to be bypassed, so the function returns NULL (check line 1424 of net/wireless/scan.c), causing the WARN_ON() in ieee80211_ibss_csa_beacon() to get triggered (check line 500 of net/mac80211/ibss.c), which was consequently reported on the syzkaller dashboard. Thus, check if we have an existing connection before generating the CSA beacon in ieee80211_ibss_finish_csa().

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_conn: Fix crash on hci_create_cis_sync When attempting to connect multiple ISO sockets without using DEFER_SETUP may result in the following crash: BUG: KASAN: null-ptr-deref in hci_create_cis_sync+0x18b/0x2b0 Read of size 2 at addr 0000000000000036 by task kworker/u3:1/50 CPU: 0 PID: 50 Comm: kworker/u3:1 Not tainted 6.0.0-rc7-02243-gb84a13ff4eda #4373 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.0-1.fc36 04/01/2014 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl+0x19/0x27 kasan_report+0xbc/0xf0 ? hci_create_cis_sync+0x18b/0x2b0 hci_create_cis_sync+0x18b/0x2b0 ? get_link_mode+0xd0/0xd0 ? __ww_mutex_lock_slowpath+0x10/0x10 ? mutex_lock+0xe0/0xe0 ? get_link_mode+0xd0/0xd0 hci_cmd_sync_work+0x111/0x190 process_one_work+0x427/0x650 worker_thread+0x87/0x750 ? process_one_work+0x650/0x650 kthread+0x14e/0x180 ? kthread_exit+0x50/0x50 ret_from_fork+0x22/0x30 </TASK>

In the Linux kernel, the following vulnerability has been resolved: media: mediatek: vcodec: Fix H264 multi stateless decoder smatch warning Fix a smatch static checker warning on vdec_h264_req_multi_if.c. Which leads to a kernel crash when fb is NULL.

In the Linux kernel, the following vulnerability has been resolved: RDMA/hns: Fix NULL pointer problem in free_mr_init() Lock grab occurs in a concurrent scenario, resulting in stepping on a NULL pointer. It should be init mutex_init() first before use the lock. Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 Call trace: __mutex_lock.constprop.0+0xd0/0x5c0 __mutex_lock_slowpath+0x1c/0x2c mutex_lock+0x44/0x50 free_mr_send_cmd_to_hw+0x7c/0x1c0 [hns_roce_hw_v2] hns_roce_v2_dereg_mr+0x30/0x40 [hns_roce_hw_v2] hns_roce_dereg_mr+0x4c/0x130 [hns_roce_hw_v2] ib_dereg_mr_user+0x54/0x124 uverbs_free_mr+0x24/0x30 destroy_hw_idr_uobject+0x38/0x74 uverbs_destroy_uobject+0x48/0x1c4 uobj_destroy+0x74/0xcc ib_uverbs_cmd_verbs+0x368/0xbb0 ib_uverbs_ioctl+0xec/0x1a4 __arm64_sys_ioctl+0xb4/0x100 invoke_syscall+0x50/0x120 el0_svc_common.constprop.0+0x58/0x190 do_el0_svc+0x30/0x90 el0_svc+0x2c/0xb4 el0t_64_sync_handler+0x1a4/0x1b0 el0t_64_sync+0x19c/0x1a0

In the Linux kernel, the following vulnerability has been resolved: filemap: Handle sibling entries in filemap_get_read_batch() If a read races with an invalidation followed by another read, it is possible for a folio to be replaced with a higher-order folio. If that happens, we'll see a sibling entry for the new folio in the next iteration of the loop. This manifests as a NULL pointer dereference while holding the RCU read lock. Handle this by simply returning. The next call will find the new folio and handle it correctly. The other ways of handling this rare race are more complex and it's just not worth it.

In the Linux kernel, the following vulnerability has been resolved: igc: Reinstate IGC_REMOVED logic and implement it properly The initially merged version of the igc driver code (via commit 146740f9abc4, "igc: Add support for PF") contained the following IGC_REMOVED checks in the igc_rd32/wr32() MMIO accessors: u32 igc_rd32(struct igc_hw *hw, u32 reg) { u8 __iomem *hw_addr = READ_ONCE(hw->hw_addr); u32 value = 0; if (IGC_REMOVED(hw_addr)) return ~value; value = readl(&hw_addr[reg]); /* reads should not return all F's */ if (!(~value) && (!reg || !(~readl(hw_addr)))) hw->hw_addr = NULL; return value; } And: #define wr32(reg, val) \ do { \ u8 __iomem *hw_addr = READ_ONCE((hw)->hw_addr); \ if (!IGC_REMOVED(hw_addr)) \ writel((val), &hw_addr[(reg)]); \ } while (0) E.g. igb has similar checks in its MMIO accessors, and has a similar macro E1000_REMOVED, which is implemented as follows: #define E1000_REMOVED(h) unlikely(!(h)) These checks serve to detect and take note of an 0xffffffff MMIO read return from the device, which can be caused by a PCIe link flap or some other kind of PCI bus error, and to avoid performing MMIO reads and writes from that point onwards. However, the IGC_REMOVED macro was not originally implemented: #ifndef IGC_REMOVED #define IGC_REMOVED(a) (0) #endif /* IGC_REMOVED */ This led to the IGC_REMOVED logic to be removed entirely in a subsequent commit (commit 3c215fb18e70, "igc: remove IGC_REMOVED function"), with the rationale that such checks matter only for virtualization and that igc does not support virtualization -- but a PCIe device can become detached even without virtualization being in use, and without proper checks, a PCIe bus error affecting an igc adapter will lead to various NULL pointer dereferences, as the first access after the error will set hw->hw_addr to NULL, and subsequent accesses will blindly dereference this now-NULL pointer. This patch reinstates the IGC_REMOVED checks in igc_rd32/wr32(), and implements IGC_REMOVED the way it is done for igb, by checking for the unlikely() case of hw_addr being NULL. This change prevents the oopses seen when a PCIe link flap occurs on an igc adapter.

A NULL pointer dereference was found in io_file_bitmap_get in io_uring/filetable.c in the io_uring sub-component in the Linux Kernel. When fixed files are unregistered, some context information (file_alloc_{start,end} and alloc_hint) is not cleared. A subsequent request that has auto index selection enabled via IORING_FILE_INDEX_ALLOC can cause a NULL pointer dereference. An unprivileged user can use the flaw to cause a system crash.

In the Linux kernel, the following vulnerability has been resolved: qede: confirm skb is allocated before using qede_build_skb() assumes build_skb() always works and goes straight to skb_reserve(). However, build_skb() can fail under memory pressure. This results in a kernel panic because the skb to reserve is NULL. Add a check in case build_skb() failed to allocate and return NULL. The NULL return is handled correctly in callers to qede_build_skb().

In the Linux kernel, the following vulnerability has been resolved: xprtrdma: fix pointer derefs in error cases of rpcrdma_ep_create If there are failures then we must not leave the non-NULL pointers with the error value, otherwise `rpcrdma_ep_destroy` gets confused and tries free them, resulting in an Oops.

In the Linux kernel, the following vulnerability has been resolved: arch/arm64: Fix topology initialization for core scheduling Arm64 systems rely on store_cpu_topology() to call update_siblings_masks() to transfer the toplogy to the various cpu masks. This needs to be done before the call to notify_cpu_starting() which tells the scheduler about each cpu found, otherwise the core scheduling data structures are setup in a way that does not match the actual topology. With smt_mask not setup correctly we bail on `cpumask_weight(smt_mask) == 1` for !leaders in: notify_cpu_starting() cpuhp_invoke_callback_range() sched_cpu_starting() sched_core_cpu_starting() which leads to rq->core not being correctly set for !leader-rq's. Without this change stress-ng (which enables core scheduling in its prctl tests in newer versions -- i.e. with PR_SCHED_CORE support) causes a warning and then a crash (trimmed for legibility): [ 1853.805168] ------------[ cut here ]------------ [ 1853.809784] task_rq(b)->core != rq->core [ 1853.809792] WARNING: CPU: 117 PID: 0 at kernel/sched/fair.c:11102 cfs_prio_less+0x1b4/0x1c4 ... [ 1854.015210] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010 ... [ 1854.231256] Call trace: [ 1854.233689] pick_next_task+0x3dc/0x81c [ 1854.237512] __schedule+0x10c/0x4cc [ 1854.240988] schedule_idle+0x34/0x54

In the Linux kernel, the following vulnerability has been resolved: ipv6: Fix ECMP sibling count mismatch when clearing RTF_ADDRCONF syzbot reported a kernel BUG in fib6_add_rt2node() when adding an IPv6 route. [0] Commit f72514b3c569 ("ipv6: clear RA flags when adding a static route") introduced logic to clear RTF_ADDRCONF from existing routes when a static route with the same nexthop is added. However, this causes a problem when the existing route has a gateway. When RTF_ADDRCONF is cleared from a route that has a gateway, that route becomes eligible for ECMP, i.e. rt6_qualify_for_ecmp() returns true. The issue is that this route was never added to the fib6_siblings list. This leads to a mismatch between the following counts: - The sibling count computed by iterating fib6_next chain, which includes the newly ECMP-eligible route - The actual siblings in fib6_siblings list, which does not include that route When a subsequent ECMP route is added, fib6_add_rt2node() hits BUG_ON(sibling->fib6_nsiblings != rt->fib6_nsiblings) because the counts don't match. Fix this by only clearing RTF_ADDRCONF when the existing route does not have a gateway. Routes without a gateway cannot qualify for ECMP anyway (rt6_qualify_for_ecmp() requires fib_nh_gw_family), so clearing RTF_ADDRCONF on them is safe and matches the original intent of the commit. [0]: kernel BUG at net/ipv6/ip6_fib.c:1217! Oops: invalid opcode: 0000 [#1] SMP KASAN PTI CPU: 0 UID: 0 PID: 6010 Comm: syz.0.17 Not tainted syzkaller #0 PREEMPT(full) Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/25/2025 RIP: 0010:fib6_add_rt2node+0x3433/0x3470 net/ipv6/ip6_fib.c:1217 [...] Call Trace: <TASK> fib6_add+0x8da/0x18a0 net/ipv6/ip6_fib.c:1532 __ip6_ins_rt net/ipv6/route.c:1351 [inline] ip6_route_add+0xde/0x1b0 net/ipv6/route.c:3946 ipv6_route_ioctl+0x35c/0x480 net/ipv6/route.c:4571 inet6_ioctl+0x219/0x280 net/ipv6/af_inet6.c:577 sock_do_ioctl+0xdc/0x300 net/socket.c:1245 sock_ioctl+0x576/0x790 net/socket.c:1366 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:597 [inline] __se_sys_ioctl+0xfc/0x170 fs/ioctl.c:583 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xfa/0xf80 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f

In the Linux kernel, the following vulnerability has been resolved: can: af_can: fix NULL pointer dereference in can_rcv_filter Analogue to commit 8aa59e355949 ("can: af_can: fix NULL pointer dereference in can_rx_register()") we need to check for a missing initialization of ml_priv in the receive path of CAN frames. Since commit 4e096a18867a ("net: introduce CAN specific pointer in the struct net_device") the check for dev->type to be ARPHRD_CAN is not sufficient anymore since bonding or tun netdevices claim to be CAN devices but do not initialize ml_priv accordingly.

In the Linux kernel, the following vulnerability has been resolved: iommu/arm-smmu: fix possible null-ptr-deref in arm_smmu_device_probe() It will cause null-ptr-deref when using 'res', if platform_get_resource() returns NULL, so move using 'res' after devm_ioremap_resource() that will check it to avoid null-ptr-deref. And use devm_platform_get_and_ioremap_resource() to simplify code.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix NULL pointer dereference in amdgpu_gmc_filter_faults_remove On APUs such as Raven and Renoir (GC 9.1.0, 9.2.2, 9.3.0), the ih1 and ih2 interrupt ring buffers are not initialized. This is by design, as these secondary IH rings are only available on discrete GPUs. See vega10_ih_sw_init() which explicitly skips ih1/ih2 initialization when AMD_IS_APU is set. However, amdgpu_gmc_filter_faults_remove() unconditionally uses ih1 to get the timestamp of the last interrupt entry. When retry faults are enabled on APUs (noretry=0), this function is called from the SVM page fault recovery path, resulting in a NULL pointer dereference when amdgpu_ih_decode_iv_ts_helper() attempts to access ih->ring[]. The crash manifests as: BUG: kernel NULL pointer dereference, address: 0000000000000004 RIP: 0010:amdgpu_ih_decode_iv_ts_helper+0x22/0x40 [amdgpu] Call Trace: amdgpu_gmc_filter_faults_remove+0x60/0x130 [amdgpu] svm_range_restore_pages+0xae5/0x11c0 [amdgpu] amdgpu_vm_handle_fault+0xc8/0x340 [amdgpu] gmc_v9_0_process_interrupt+0x191/0x220 [amdgpu] amdgpu_irq_dispatch+0xed/0x2c0 [amdgpu] amdgpu_ih_process+0x84/0x100 [amdgpu] This issue was exposed by commit 1446226d32a4 ("drm/amdgpu: Remove GC HW IP 9.3.0 from noretry=1") which changed the default for Renoir APU from noretry=1 to noretry=0, enabling retry fault handling and thus exercising the buggy code path. Fix this by adding a check for ih1.ring_size before attempting to use it. Also restore the soft_ih support from commit dd299441654f ("drm/amdgpu: Rework retry fault removal"). This is needed if the hardware doesn't support secondary HW IH rings. v2: additional updates (Alex) (cherry picked from commit 6ce8d536c80aa1f059e82184f0d1994436b1d526)

In the Linux kernel, the following vulnerability has been resolved: staging: vchiq_core: handle NULL result of find_service_by_handle In case of an invalid handle the function find_servive_by_handle returns NULL. So take care of this and avoid a NULL pointer dereference.