In the Linux kernel, the following vulnerability has been resolved: mtd: require write permissions for locking and badblock ioctls MEMLOCK, MEMUNLOCK and OTPLOCK modify protection bits. Thus require write permission. Depending on the hardware MEMLOCK might even be write-once, e.g. for SPI-NOR flashes with their WP# tied to GND. OTPLOCK is always write-once. MEMSETBADBLOCK modifies the bad block table.

In the Linux kernel, the following vulnerability has been resolved: scsi: ufs: Fix a deadlock in the error handler The following deadlock has been observed on a test setup: - All tags allocated - The SCSI error handler calls ufshcd_eh_host_reset_handler() - ufshcd_eh_host_reset_handler() queues work that calls ufshcd_err_handler() - ufshcd_err_handler() locks up as follows: Workqueue: ufs_eh_wq_0 ufshcd_err_handler.cfi_jt Call trace: __switch_to+0x298/0x5d8 __schedule+0x6cc/0xa94 schedule+0x12c/0x298 blk_mq_get_tag+0x210/0x480 __blk_mq_alloc_request+0x1c8/0x284 blk_get_request+0x74/0x134 ufshcd_exec_dev_cmd+0x68/0x640 ufshcd_verify_dev_init+0x68/0x35c ufshcd_probe_hba+0x12c/0x1cb8 ufshcd_host_reset_and_restore+0x88/0x254 ufshcd_reset_and_restore+0xd0/0x354 ufshcd_err_handler+0x408/0xc58 process_one_work+0x24c/0x66c worker_thread+0x3e8/0xa4c kthread+0x150/0x1b4 ret_from_fork+0x10/0x30 Fix this lockup by making ufshcd_exec_dev_cmd() allocate a reserved request.

In the Linux kernel, the following vulnerability has been resolved: mptcp: fix deadlock in __mptcp_push_pending() __mptcp_push_pending() may call mptcp_flush_join_list() with subflow socket lock held. If such call hits mptcp_sockopt_sync_all() then subsequently __mptcp_sockopt_sync() could try to lock the subflow socket for itself, causing a deadlock. sysrq: Show Blocked State task:ss-server state:D stack: 0 pid: 938 ppid: 1 flags:0x00000000 Call Trace: <TASK> __schedule+0x2d6/0x10c0 ? __mod_memcg_state+0x4d/0x70 ? csum_partial+0xd/0x20 ? _raw_spin_lock_irqsave+0x26/0x50 schedule+0x4e/0xc0 __lock_sock+0x69/0x90 ? do_wait_intr_irq+0xa0/0xa0 __lock_sock_fast+0x35/0x50 mptcp_sockopt_sync_all+0x38/0xc0 __mptcp_push_pending+0x105/0x200 mptcp_sendmsg+0x466/0x490 sock_sendmsg+0x57/0x60 __sys_sendto+0xf0/0x160 ? do_wait_intr_irq+0xa0/0xa0 ? fpregs_restore_userregs+0x12/0xd0 __x64_sys_sendto+0x20/0x30 do_syscall_64+0x38/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f9ba546c2d0 RSP: 002b:00007ffdc3b762d8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 00007f9ba56c8060 RCX: 00007f9ba546c2d0 RDX: 000000000000077a RSI: 0000000000e5e180 RDI: 0000000000000234 RBP: 0000000000cc57f0 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f9ba56c8060 R13: 0000000000b6ba60 R14: 0000000000cc7840 R15: 41d8685b1d7901b8 </TASK> Fix the issue by using __mptcp_flush_join_list() instead of plain mptcp_flush_join_list() inside __mptcp_push_pending(), as suggested by Florian. The sockopt sync will be deferred to the workqueue.

In the Linux kernel, the following vulnerability has been resolved: iio: adis16475: fix deadlock on frequency set With commit 39c024b51b560 ("iio: adis16475: improve sync scale mode handling"), two deadlocks were introduced: 1) The call to 'adis_write_reg_16()' was not changed to it's unlocked version. 2) The lock was not being released on the success path of the function. This change fixes both these issues.

An issue was discovered in the Linux kernel through 5.6.11. btree_gc_coalesce in drivers/md/bcache/btree.c has a deadlock if a coalescing operation fails.

TensorFlow is an open source platform for machine learning. In affected versions the code behind `tf.function` API can be made to deadlock when two `tf.function` decorated Python functions are mutually recursive. This occurs due to using a non-reentrant `Lock` Python object. Loading any model which contains mutually recursive functions is vulnerable. An attacker can cause denial of service by causing users to load such models and calling a recursive `tf.function`, although this is not a frequent scenario. The fix will be included in TensorFlow 2.7.0. We will also cherrypick this commit on TensorFlow 2.6.1, TensorFlow 2.5.2, and TensorFlow 2.4.4, as these are also affected and still in supported range.

A vulnerability was found in btrfs_alloc_tree_b in fs/btrfs/extent-tree.c in the Linux kernel due to an improper lock operation in btrfs. In this flaw, a user with a local privilege may cause a denial of service (DOS) due to a deadlock problem.

A flaw was found in the X server's request handling. Non-zero 'bytes to ignore' in a client's request can cause the server to skip processing another client's request, potentially leading to a denial of service.

Cortex-A77 cores (r0p0 and r1p0) are affected by erratum 1508412 where software, under certain circumstances, could deadlock a core due to the execution of either a load to device or non-cacheable memory, and either a store exclusive or register read of the Physical Address Register (PAR_EL1) in close proximity.

btrfs in the Linux kernel before 5.13.4 allows attackers to cause a denial of service (deadlock) via processes that trigger allocation of new system chunks during times when there is a shortage of free space in the system space_info.

In the Linux kernel, the following vulnerability has been resolved: cgroup/cpuset: remove kernfs active break A warning was found: WARNING: CPU: 10 PID: 3486953 at fs/kernfs/file.c:828 CPU: 10 PID: 3486953 Comm: rmdir Kdump: loaded Tainted: G RIP: 0010:kernfs_should_drain_open_files+0x1a1/0x1b0 RSP: 0018:ffff8881107ef9e0 EFLAGS: 00010202 RAX: 0000000080000002 RBX: ffff888154738c00 RCX: dffffc0000000000 RDX: 0000000000000007 RSI: 0000000000000004 RDI: ffff888154738c04 RBP: ffff888154738c04 R08: ffffffffaf27fa15 R09: ffffed102a8e7180 R10: ffff888154738c07 R11: 0000000000000000 R12: ffff888154738c08 R13: ffff888750f8c000 R14: ffff888750f8c0e8 R15: ffff888154738ca0 FS: 00007f84cd0be740(0000) GS:ffff8887ddc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000555f9fbe00c8 CR3: 0000000153eec001 CR4: 0000000000370ee0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: kernfs_drain+0x15e/0x2f0 __kernfs_remove+0x165/0x300 kernfs_remove_by_name_ns+0x7b/0xc0 cgroup_rm_file+0x154/0x1c0 cgroup_addrm_files+0x1c2/0x1f0 css_clear_dir+0x77/0x110 kill_css+0x4c/0x1b0 cgroup_destroy_locked+0x194/0x380 cgroup_rmdir+0x2a/0x140 It can be explained by: rmdir echo 1 > cpuset.cpus kernfs_fop_write_iter // active=0 cgroup_rm_file kernfs_remove_by_name_ns kernfs_get_active // active=1 __kernfs_remove // active=0x80000002 kernfs_drain cpuset_write_resmask wait_event //waiting (active == 0x80000001) kernfs_break_active_protection // active = 0x80000001 // continue kernfs_unbreak_active_protection // active = 0x80000002 ... kernfs_should_drain_open_files // warning occurs kernfs_put_active This warning is caused by 'kernfs_break_active_protection' when it is writing to cpuset.cpus, and the cgroup is removed concurrently. The commit 3a5a6d0c2b03 ("cpuset: don't nest cgroup_mutex inside get_online_cpus()") made cpuset_hotplug_workfn asynchronous, This change involves calling flush_work(), which can create a multiple processes circular locking dependency that involve cgroup_mutex, potentially leading to a deadlock. To avoid deadlock. the commit 76bb5ab8f6e3 ("cpuset: break kernfs active protection in cpuset_write_resmask()") added 'kernfs_break_active_protection' in the cpuset_write_resmask. This could lead to this warning. After the commit 2125c0034c5d ("cgroup/cpuset: Make cpuset hotplug processing synchronous"), the cpuset_write_resmask no longer needs to wait the hotplug to finish, which means that concurrent hotplug and cpuset operations are no longer possible. Therefore, the deadlock doesn't exist anymore and it does not have to 'break active protection' now. To fix this warning, just remove kernfs_break_active_protection operation in the 'cpuset_write_resmask'.

A vulnerability was found due to missing lock for IOPOLL flaw in io_cqring_event_overflow() in io_uring.c in Linux Kernel. This flaw allows a local attacker with user privilege to trigger a Denial of Service threat.

In the Linux kernel, the following vulnerability has been resolved: media: uvcvideo: Fix deadlock during uvc_probe If uvc_probe() fails, it can end up calling uvc_status_unregister() before uvc_status_init() is called. Fix this by checking if dev->status is NULL or not in uvc_status_unregister().

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: iso: Fix circular lock in iso_listen_bis This fixes the circular locking dependency warning below, by releasing the socket lock before enterning iso_listen_bis, to avoid any potential deadlock with hdev lock. [ 75.307983] ====================================================== [ 75.307984] WARNING: possible circular locking dependency detected [ 75.307985] 6.12.0-rc6+ #22 Not tainted [ 75.307987] ------------------------------------------------------ [ 75.307987] kworker/u81:2/2623 is trying to acquire lock: [ 75.307988] ffff8fde1769da58 (sk_lock-AF_BLUETOOTH-BTPROTO_ISO) at: iso_connect_cfm+0x253/0x840 [bluetooth] [ 75.308021] but task is already holding lock: [ 75.308022] ffff8fdd61a10078 (&hdev->lock) at: hci_le_per_adv_report_evt+0x47/0x2f0 [bluetooth] [ 75.308053] which lock already depends on the new lock. [ 75.308054] the existing dependency chain (in reverse order) is: [ 75.308055] -> #1 (&hdev->lock){+.+.}-{3:3}: [ 75.308057] __mutex_lock+0xad/0xc50 [ 75.308061] mutex_lock_nested+0x1b/0x30 [ 75.308063] iso_sock_listen+0x143/0x5c0 [bluetooth] [ 75.308085] __sys_listen_socket+0x49/0x60 [ 75.308088] __x64_sys_listen+0x4c/0x90 [ 75.308090] x64_sys_call+0x2517/0x25f0 [ 75.308092] do_syscall_64+0x87/0x150 [ 75.308095] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 75.308098] -> #0 (sk_lock-AF_BLUETOOTH-BTPROTO_ISO){+.+.}-{0:0}: [ 75.308100] __lock_acquire+0x155e/0x25f0 [ 75.308103] lock_acquire+0xc9/0x300 [ 75.308105] lock_sock_nested+0x32/0x90 [ 75.308107] iso_connect_cfm+0x253/0x840 [bluetooth] [ 75.308128] hci_connect_cfm+0x6c/0x190 [bluetooth] [ 75.308155] hci_le_per_adv_report_evt+0x27b/0x2f0 [bluetooth] [ 75.308180] hci_le_meta_evt+0xe7/0x200 [bluetooth] [ 75.308206] hci_event_packet+0x21f/0x5c0 [bluetooth] [ 75.308230] hci_rx_work+0x3ae/0xb10 [bluetooth] [ 75.308254] process_one_work+0x212/0x740 [ 75.308256] worker_thread+0x1bd/0x3a0 [ 75.308258] kthread+0xe4/0x120 [ 75.308259] ret_from_fork+0x44/0x70 [ 75.308261] ret_from_fork_asm+0x1a/0x30 [ 75.308263] other info that might help us debug this: [ 75.308264] Possible unsafe locking scenario: [ 75.308264] CPU0 CPU1 [ 75.308265] ---- ---- [ 75.308265] lock(&hdev->lock); [ 75.308267] lock(sk_lock- AF_BLUETOOTH-BTPROTO_ISO); [ 75.308268] lock(&hdev->lock); [ 75.308269] lock(sk_lock-AF_BLUETOOTH-BTPROTO_ISO); [ 75.308270] *** DEADLOCK *** [ 75.308271] 4 locks held by kworker/u81:2/2623: [ 75.308272] #0: ffff8fdd66e52148 ((wq_completion)hci0#2){+.+.}-{0:0}, at: process_one_work+0x443/0x740 [ 75.308276] #1: ffffafb488b7fe48 ((work_completion)(&hdev->rx_work)), at: process_one_work+0x1ce/0x740 [ 75.308280] #2: ffff8fdd61a10078 (&hdev->lock){+.+.}-{3:3} at: hci_le_per_adv_report_evt+0x47/0x2f0 [bluetooth] [ 75.308304] #3: ffffffffb6ba4900 (rcu_read_lock){....}-{1:2}, at: hci_connect_cfm+0x29/0x190 [bluetooth]

The kernel in Red Hat Enterprise Linux 3, when running on SMP systems, allows local users to cause a denial of service (deadlock) by running the shmat function on an shm at the same time that shmctl is removing that shm (IPC_RMID), which prevents a spinlock from being unlocked.

The Server Message Block (SMB) driver (MRXSMB.SYS) in Microsoft Windows 2000 SP4, XP SP1 and SP2, and Server 2003 SP1 and earlier allows local users to cause a denial of service (hang) by calling the MrxSmbCscIoctlCloseForCopyChunk with the file handle of the shadow device, which results in a deadlock, aka the "SMB Invalid Handle Vulnerability."

In the Linux kernel, the following vulnerability has been resolved: scsi: ufs: core: Fix another deadlock during RTC update If ufshcd_rtc_work calls ufshcd_rpm_put_sync() and the pm's usage_count is 0, we will enter the runtime suspend callback. However, the runtime suspend callback will wait to flush ufshcd_rtc_work, causing a deadlock. Replace ufshcd_rpm_put_sync() with ufshcd_rpm_put() to avoid the deadlock.

A deadlock flaw was found in the Linux kernel’s BPF subsystem. This flaw allows a local user to potentially crash the system.

Array index overflow in the xfrm_sk_policy_insert function in xfrm_user.c in Linux kernel 2.6 allows local users to cause a denial of service (oops or deadlock) and possibly execute arbitrary code via a p->dir value that is larger than XFRM_POLICY_OUT, which is used as an index in the sock->sk_policy array.

In libstagefright, there is a possible use-after-free due to improper locking. This could lead to local escalation of privilege in the media server with no additional execution privileges needed. User interaction is not needed for exploitation. Product: AndroidVersions: Android-10Android ID: A-77474014

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix deadlock in nilfs_count_free_blocks() A semaphore deadlock can occur if nilfs_get_block() detects metadata corruption while locating data blocks and a superblock writeback occurs at the same time: task 1 task 2 ------ ------ * A file operation * nilfs_truncate() nilfs_get_block() down_read(rwsem A) <-- nilfs_bmap_lookup_contig() ... generic_shutdown_super() nilfs_put_super() * Prepare to write superblock * down_write(rwsem B) <-- nilfs_cleanup_super() * Detect b-tree corruption * nilfs_set_log_cursor() nilfs_bmap_convert_error() nilfs_count_free_blocks() __nilfs_error() down_read(rwsem A) <-- nilfs_set_error() down_write(rwsem B) <-- *** DEADLOCK *** Here, nilfs_get_block() readlocks rwsem A (= NILFS_MDT(dat_inode)->mi_sem) and then calls nilfs_bmap_lookup_contig(), but if it fails due to metadata corruption, __nilfs_error() is called from nilfs_bmap_convert_error() inside the lock section. Since __nilfs_error() calls nilfs_set_error() unless the filesystem is read-only and nilfs_set_error() attempts to writelock rwsem B (= nilfs->ns_sem) to write back superblock exclusively, hierarchical lock acquisition occurs in the order rwsem A -> rwsem B. Now, if another task starts updating the superblock, it may writelock rwsem B during the lock sequence above, and can deadlock trying to readlock rwsem A in nilfs_count_free_blocks(). However, there is actually no need to take rwsem A in nilfs_count_free_blocks() because it, within the lock section, only reads a single integer data on a shared struct with nilfs_sufile_get_ncleansegs(). This has been the case after commit aa474a220180 ("nilfs2: add local variable to cache the number of clean segments"), that is, even before this bug was introduced. So, this resolves the deadlock problem by just not taking the semaphore in nilfs_count_free_blocks().

dump 0.4 b10 through b29 allows local users to cause a denial of service (execution prevention) by using flock() to lock the /etc/dumpdates file.

In the Linux kernel, the following vulnerability has been resolved: tty: fix deadlock caused by calling printk() under tty_port->lock pty_write() invokes kmalloc() which may invoke a normal printk() to print failure message. This can cause a deadlock in the scenario reported by syz-bot below: CPU0 CPU1 CPU2 ---- ---- ---- lock(console_owner); lock(&port_lock_key); lock(&port->lock); lock(&port_lock_key); lock(&port->lock); lock(console_owner); As commit dbdda842fe96 ("printk: Add console owner and waiter logic to load balance console writes") said, such deadlock can be prevented by using printk_deferred() in kmalloc() (which is invoked in the section guarded by the port->lock). But there are too many printk() on the kmalloc() path, and kmalloc() can be called from anywhere, so changing printk() to printk_deferred() is too complicated and inelegant. Therefore, this patch chooses to specify __GFP_NOWARN to kmalloc(), so that printk() will not be called, and this deadlock problem can be avoided. Syzbot reported the following lockdep error: ====================================================== WARNING: possible circular locking dependency detected 5.4.143-00237-g08ccc19a-dirty #10 Not tainted ------------------------------------------------------ syz-executor.4/29420 is trying to acquire lock: ffffffff8aedb2a0 (console_owner){....}-{0:0}, at: console_trylock_spinning kernel/printk/printk.c:1752 [inline] ffffffff8aedb2a0 (console_owner){....}-{0:0}, at: vprintk_emit+0x2ca/0x470 kernel/printk/printk.c:2023 but task is already holding lock: ffff8880119c9158 (&port->lock){-.-.}-{2:2}, at: pty_write+0xf4/0x1f0 drivers/tty/pty.c:120 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (&port->lock){-.-.}-{2:2}: __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline] _raw_spin_lock_irqsave+0x35/0x50 kernel/locking/spinlock.c:159 tty_port_tty_get drivers/tty/tty_port.c:288 [inline] <-- lock(&port->lock); tty_port_default_wakeup+0x1d/0xb0 drivers/tty/tty_port.c:47 serial8250_tx_chars+0x530/0xa80 drivers/tty/serial/8250/8250_port.c:1767 serial8250_handle_irq.part.0+0x31f/0x3d0 drivers/tty/serial/8250/8250_port.c:1854 serial8250_handle_irq drivers/tty/serial/8250/8250_port.c:1827 [inline] <-- lock(&port_lock_key); serial8250_default_handle_irq+0xb2/0x220 drivers/tty/serial/8250/8250_port.c:1870 serial8250_interrupt+0xfd/0x200 drivers/tty/serial/8250/8250_core.c:126 __handle_irq_event_percpu+0x109/0xa50 kernel/irq/handle.c:156 [...] -> #1 (&port_lock_key){-.-.}-{2:2}: __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline] _raw_spin_lock_irqsave+0x35/0x50 kernel/locking/spinlock.c:159 serial8250_console_write+0x184/0xa40 drivers/tty/serial/8250/8250_port.c:3198 <-- lock(&port_lock_key); call_console_drivers kernel/printk/printk.c:1819 [inline] console_unlock+0x8cb/0xd00 kernel/printk/printk.c:2504 vprintk_emit+0x1b5/0x470 kernel/printk/printk.c:2024 <-- lock(console_owner); vprintk_func+0x8d/0x250 kernel/printk/printk_safe.c:394 printk+0xba/0xed kernel/printk/printk.c:2084 register_console+0x8b3/0xc10 kernel/printk/printk.c:2829 univ8250_console_init+0x3a/0x46 drivers/tty/serial/8250/8250_core.c:681 console_init+0x49d/0x6d3 kernel/printk/printk.c:2915 start_kernel+0x5e9/0x879 init/main.c:713 secondary_startup_64+0xa4/0xb0 arch/x86/kernel/head_64.S:241 -> #0 (console_owner){....}-{0:0}: [...] lock_acquire+0x127/0x340 kernel/locking/lockdep.c:4734 console_trylock_spinning kernel/printk/printk.c:1773 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: NFSv4: Don't hold the layoutget locks across multiple RPC calls When doing layoutget as part of the open() compound, we have to be careful to release the layout locks before we can call any further RPC calls, such as setattr(). The reason is that those calls could trigger a recall, which could deadlock.

In the Linux kernel, the following vulnerability has been resolved: tracing: Fix sleeping function called from invalid context on RT kernel When setting bootparams="trace_event=initcall:initcall_start tp_printk=1" in the cmdline, the output_printk() was called, and the spin_lock_irqsave() was called in the atomic and irq disable interrupt context suitation. On the PREEMPT_RT kernel, these locks are replaced with sleepable rt-spinlock, so the stack calltrace will be triggered. Fix it by raw_spin_lock_irqsave when PREEMPT_RT and "trace_event=initcall:initcall_start tp_printk=1" enabled. BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:46 in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 1, name: swapper/0 preempt_count: 2, expected: 0 RCU nest depth: 0, expected: 0 Preemption disabled at: [<ffffffff8992303e>] try_to_wake_up+0x7e/0xba0 CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.17.1-rt17+ #19 34c5812404187a875f32bee7977f7367f9679ea7 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-2 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x60/0x8c dump_stack+0x10/0x12 __might_resched.cold+0x11d/0x155 rt_spin_lock+0x40/0x70 trace_event_buffer_commit+0x2fa/0x4c0 ? map_vsyscall+0x93/0x93 trace_event_raw_event_initcall_start+0xbe/0x110 ? perf_trace_initcall_finish+0x210/0x210 ? probe_sched_wakeup+0x34/0x40 ? ttwu_do_wakeup+0xda/0x310 ? trace_hardirqs_on+0x35/0x170 ? map_vsyscall+0x93/0x93 do_one_initcall+0x217/0x3c0 ? trace_event_raw_event_initcall_level+0x170/0x170 ? push_cpu_stop+0x400/0x400 ? cblist_init_generic+0x241/0x290 kernel_init_freeable+0x1ac/0x347 ? _raw_spin_unlock_irq+0x65/0x80 ? rest_init+0xf0/0xf0 kernel_init+0x1e/0x150 ret_from_fork+0x22/0x30 </TASK>

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Fix SCSI I/O completion and abort handler deadlock During stress I/O tests with 500+ vports, hard LOCKUP call traces are observed. CPU A: native_queued_spin_lock_slowpath+0x192 _raw_spin_lock_irqsave+0x32 lpfc_handle_fcp_err+0x4c6 lpfc_fcp_io_cmd_wqe_cmpl+0x964 lpfc_sli4_fp_handle_cqe+0x266 __lpfc_sli4_process_cq+0x105 __lpfc_sli4_hba_process_cq+0x3c lpfc_cq_poll_hdler+0x16 irq_poll_softirq+0x76 __softirqentry_text_start+0xe4 irq_exit+0xf7 do_IRQ+0x7f CPU B: native_queued_spin_lock_slowpath+0x5b _raw_spin_lock+0x1c lpfc_abort_handler+0x13e scmd_eh_abort_handler+0x85 process_one_work+0x1a7 worker_thread+0x30 kthread+0x112 ret_from_fork+0x1f Diagram of lockup: CPUA CPUB ---- ---- lpfc_cmd->buf_lock phba->hbalock lpfc_cmd->buf_lock phba->hbalock Fix by reordering the taking of the lpfc_cmd->buf_lock and phba->hbalock in lpfc_abort_handler routine so that it tries to take the lpfc_cmd->buf_lock first before phba->hbalock.

Concurrent Versions Software (CVS) uses predictable temporary file names for locking, which allows local users to cause a denial of service by creating the lock directory before it is created for use by a legitimate CVS user.

In the Linux kernel, the following vulnerability has been resolved: mptcp: init: protect sched with rcu_read_lock Enabling CONFIG_PROVE_RCU_LIST with its dependence CONFIG_RCU_EXPERT creates this splat when an MPTCP socket is created: ============================= WARNING: suspicious RCU usage 6.12.0-rc2+ #11 Not tainted ----------------------------- net/mptcp/sched.c:44 RCU-list traversed in non-reader section!! other info that might help us debug this: rcu_scheduler_active = 2, debug_locks = 1 no locks held by mptcp_connect/176. stack backtrace: CPU: 0 UID: 0 PID: 176 Comm: mptcp_connect Not tainted 6.12.0-rc2+ #11 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 Call Trace: <TASK> dump_stack_lvl (lib/dump_stack.c:123) lockdep_rcu_suspicious (kernel/locking/lockdep.c:6822) mptcp_sched_find (net/mptcp/sched.c:44 (discriminator 7)) mptcp_init_sock (net/mptcp/protocol.c:2867 (discriminator 1)) ? sock_init_data_uid (arch/x86/include/asm/atomic.h:28) inet_create.part.0.constprop.0 (net/ipv4/af_inet.c:386) ? __sock_create (include/linux/rcupdate.h:347 (discriminator 1)) __sock_create (net/socket.c:1576) __sys_socket (net/socket.c:1671) ? __pfx___sys_socket (net/socket.c:1712) ? do_user_addr_fault (arch/x86/mm/fault.c:1419 (discriminator 1)) __x64_sys_socket (net/socket.c:1728) do_syscall_64 (arch/x86/entry/common.c:52 (discriminator 1)) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130) That's because when the socket is initialised, rcu_read_lock() is not used despite the explicit comment written above the declaration of mptcp_sched_find() in sched.c. Adding the missing lock/unlock avoids the warning.

In the Linux kernel, the following vulnerability has been resolved: tpm: Lock TPM chip in tpm_pm_suspend() first Setting TPM_CHIP_FLAG_SUSPENDED in the end of tpm_pm_suspend() can be racy according, as this leaves window for tpm_hwrng_read() to be called while the operation is in progress. The recent bug report gives also evidence of this behaviour. Aadress this by locking the TPM chip before checking any chip->flags both in tpm_pm_suspend() and tpm_hwrng_read(). Move TPM_CHIP_FLAG_SUSPENDED check inside tpm_get_random() so that it will be always checked only when the lock is reserved.

In the Linux kernel, the following vulnerability has been resolved: bcache: avoid journal no-space deadlock by reserving 1 journal bucket The journal no-space deadlock was reported time to time. Such deadlock can happen in the following situation. When all journal buckets are fully filled by active jset with heavy write I/O load, the cache set registration (after a reboot) will load all active jsets and inserting them into the btree again (which is called journal replay). If a journaled bkey is inserted into a btree node and results btree node split, new journal request might be triggered. For example, the btree grows one more level after the node split, then the root node record in cache device super block will be upgrade by bch_journal_meta() from bch_btree_set_root(). But there is no space in journal buckets, the journal replay has to wait for new journal bucket to be reclaimed after at least one journal bucket replayed. This is one example that how the journal no-space deadlock happens. The solution to avoid the deadlock is to reserve 1 journal bucket in run time, and only permit the reserved journal bucket to be used during cache set registration procedure for things like journal replay. Then the journal space will never be fully filled, there is no chance for journal no-space deadlock to happen anymore. This patch adds a new member "bool do_reserve" in struct journal, it is inititalized to 0 (false) when struct journal is allocated, and set to 1 (true) by bch_journal_space_reserve() when all initialization done in run_cache_set(). In the run time when journal_reclaim() tries to allocate a new journal bucket, free_journal_buckets() is called to check whether there are enough free journal buckets to use. If there is only 1 free journal bucket and journal->do_reserve is 1 (true), the last bucket is reserved and free_journal_buckets() will return 0 to indicate no free journal bucket. Then journal_reclaim() will give up, and try next time to see whetheer there is free journal bucket to allocate. By this method, there is always 1 jouranl bucket reserved in run time. During the cache set registration, journal->do_reserve is 0 (false), so the reserved journal bucket can be used to avoid the no-space deadlock.

In the Linux kernel, the following vulnerability has been resolved: loop: implement ->free_disk Ensure that the lo_device which is stored in the gendisk private data is valid until the gendisk is freed. Currently the loop driver uses a lot of effort to make sure a device is not freed when it is still in use, but to to fix a potential deadlock this will be relaxed a bit soon.

In the Linux kernel, the following vulnerability has been resolved: drm/vc4: Fix deadlock on DSI device attach error DSI device attach to DSI host will be done with host device's lock held. Un-registering host in "device attach" error path (ex: probe retry) will result in deadlock with below call trace and non operational DSI display. Startup Call trace: [ 35.043036] rt_mutex_slowlock.constprop.21+0x184/0x1b8 [ 35.043048] mutex_lock_nested+0x7c/0xc8 [ 35.043060] device_del+0x4c/0x3e8 [ 35.043075] device_unregister+0x20/0x40 [ 35.043082] mipi_dsi_remove_device_fn+0x18/0x28 [ 35.043093] device_for_each_child+0x68/0xb0 [ 35.043105] mipi_dsi_host_unregister+0x40/0x90 [ 35.043115] vc4_dsi_host_attach+0xf0/0x120 [vc4] [ 35.043199] mipi_dsi_attach+0x30/0x48 [ 35.043209] tc358762_probe+0x128/0x164 [tc358762] [ 35.043225] mipi_dsi_drv_probe+0x28/0x38 [ 35.043234] really_probe+0xc0/0x318 [ 35.043244] __driver_probe_device+0x80/0xe8 [ 35.043254] driver_probe_device+0xb8/0x118 [ 35.043263] __device_attach_driver+0x98/0xe8 [ 35.043273] bus_for_each_drv+0x84/0xd8 [ 35.043281] __device_attach+0xf0/0x150 [ 35.043290] device_initial_probe+0x1c/0x28 [ 35.043300] bus_probe_device+0xa4/0xb0 [ 35.043308] deferred_probe_work_func+0xa0/0xe0 [ 35.043318] process_one_work+0x254/0x700 [ 35.043330] worker_thread+0x4c/0x448 [ 35.043339] kthread+0x19c/0x1a8 [ 35.043348] ret_from_fork+0x10/0x20 Shutdown Call trace: [ 365.565417] Call trace: [ 365.565423] __switch_to+0x148/0x200 [ 365.565452] __schedule+0x340/0x9c8 [ 365.565467] schedule+0x48/0x110 [ 365.565479] schedule_timeout+0x3b0/0x448 [ 365.565496] wait_for_completion+0xac/0x138 [ 365.565509] __flush_work+0x218/0x4e0 [ 365.565523] flush_work+0x1c/0x28 [ 365.565536] wait_for_device_probe+0x68/0x158 [ 365.565550] device_shutdown+0x24/0x348 [ 365.565561] kernel_restart_prepare+0x40/0x50 [ 365.565578] kernel_restart+0x20/0x70 [ 365.565591] __do_sys_reboot+0x10c/0x220 [ 365.565605] __arm64_sys_reboot+0x2c/0x38 [ 365.565619] invoke_syscall+0x4c/0x110 [ 365.565634] el0_svc_common.constprop.3+0xfc/0x120 [ 365.565648] do_el0_svc+0x2c/0x90 [ 365.565661] el0_svc+0x4c/0xf0 [ 365.565671] el0t_64_sync_handler+0x90/0xb8 [ 365.565682] el0t_64_sync+0x180/0x184

In the Linux kernel, the following vulnerability has been resolved: mm/kmemleak: avoid scanning potential huge holes When using devm_request_free_mem_region() and devm_memremap_pages() to add ZONE_DEVICE memory, if requested free mem region's end pfn were huge(e.g., 0x400000000), the node_end_pfn() will be also huge (see move_pfn_range_to_zone()). Thus it creates a huge hole between node_start_pfn() and node_end_pfn(). We found on some AMD APUs, amdkfd requested such a free mem region and created a huge hole. In such a case, following code snippet was just doing busy test_bit() looping on the huge hole. for (pfn = start_pfn; pfn < end_pfn; pfn++) { struct page *page = pfn_to_online_page(pfn); if (!page) continue; ... } So we got a soft lockup: watchdog: BUG: soft lockup - CPU#6 stuck for 26s! [bash:1221] CPU: 6 PID: 1221 Comm: bash Not tainted 5.15.0-custom #1 RIP: 0010:pfn_to_online_page+0x5/0xd0 Call Trace: ? kmemleak_scan+0x16a/0x440 kmemleak_write+0x306/0x3a0 ? common_file_perm+0x72/0x170 full_proxy_write+0x5c/0x90 vfs_write+0xb9/0x260 ksys_write+0x67/0xe0 __x64_sys_write+0x1a/0x20 do_syscall_64+0x3b/0xc0 entry_SYSCALL_64_after_hwframe+0x44/0xae I did some tests with the patch. (1) amdgpu module unloaded before the patch: real 0m0.976s user 0m0.000s sys 0m0.968s after the patch: real 0m0.981s user 0m0.000s sys 0m0.973s (2) amdgpu module loaded before the patch: real 0m35.365s user 0m0.000s sys 0m35.354s after the patch: real 0m1.049s user 0m0.000s sys 0m1.042s

In the Linux kernel, the following vulnerability has been resolved: net, neigh: Do not trigger immediate probes on NUD_FAILED from neigh_managed_work syzkaller was able to trigger a deadlock for NTF_MANAGED entries [0]: kworker/0:16/14617 is trying to acquire lock: ffffffff8d4dd370 (&tbl->lock){++-.}-{2:2}, at: ___neigh_create+0x9e1/0x2990 net/core/neighbour.c:652 [...] but task is already holding lock: ffffffff8d4dd370 (&tbl->lock){++-.}-{2:2}, at: neigh_managed_work+0x35/0x250 net/core/neighbour.c:1572 The neighbor entry turned to NUD_FAILED state, where __neigh_event_send() triggered an immediate probe as per commit cd28ca0a3dd1 ("neigh: reduce arp latency") via neigh_probe() given table lock was held. One option to fix this situation is to defer the neigh_probe() back to the neigh_timer_handler() similarly as pre cd28ca0a3dd1. For the case of NTF_MANAGED, this deferral is acceptable given this only happens on actual failure state and regular / expected state is NUD_VALID with the entry already present. The fix adds a parameter to __neigh_event_send() in order to communicate whether immediate probe is allowed or disallowed. Existing call-sites of neigh_event_send() default as-is to immediate probe. However, the neigh_managed_work() disables it via use of neigh_event_send_probe(). [0] <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 print_deadlock_bug kernel/locking/lockdep.c:2956 [inline] check_deadlock kernel/locking/lockdep.c:2999 [inline] validate_chain kernel/locking/lockdep.c:3788 [inline] __lock_acquire.cold+0x149/0x3ab kernel/locking/lockdep.c:5027 lock_acquire kernel/locking/lockdep.c:5639 [inline] lock_acquire+0x1ab/0x510 kernel/locking/lockdep.c:5604 __raw_write_lock_bh include/linux/rwlock_api_smp.h:202 [inline] _raw_write_lock_bh+0x2f/0x40 kernel/locking/spinlock.c:334 ___neigh_create+0x9e1/0x2990 net/core/neighbour.c:652 ip6_finish_output2+0x1070/0x14f0 net/ipv6/ip6_output.c:123 __ip6_finish_output net/ipv6/ip6_output.c:191 [inline] __ip6_finish_output+0x61e/0xe90 net/ipv6/ip6_output.c:170 ip6_finish_output+0x32/0x200 net/ipv6/ip6_output.c:201 NF_HOOK_COND include/linux/netfilter.h:296 [inline] ip6_output+0x1e4/0x530 net/ipv6/ip6_output.c:224 dst_output include/net/dst.h:451 [inline] NF_HOOK include/linux/netfilter.h:307 [inline] ndisc_send_skb+0xa99/0x17f0 net/ipv6/ndisc.c:508 ndisc_send_ns+0x3a9/0x840 net/ipv6/ndisc.c:650 ndisc_solicit+0x2cd/0x4f0 net/ipv6/ndisc.c:742 neigh_probe+0xc2/0x110 net/core/neighbour.c:1040 __neigh_event_send+0x37d/0x1570 net/core/neighbour.c:1201 neigh_event_send include/net/neighbour.h:470 [inline] neigh_managed_work+0x162/0x250 net/core/neighbour.c:1574 process_one_work+0x9ac/0x1650 kernel/workqueue.c:2307 worker_thread+0x657/0x1110 kernel/workqueue.c:2454 kthread+0x2e9/0x3a0 kernel/kthread.c:377 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295 </TASK>

In the Linux kernel before 4.16.4, a double-locking error in drivers/usb/dwc3/gadget.c may potentially cause a deadlock with f_hid.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix WARNING "do not call blocking ops when !TASK_RUNNING" wait_event_timeout() will set the state of the current task to TASK_UNINTERRUPTIBLE, before doing the condition check. This means that ksmbd_durable_scavenger_alive() will try to acquire the mutex while already in a sleeping state. The scheduler warns us by giving the following warning: do not call blocking ops when !TASK_RUNNING; state=2 set at [<0000000061515a6f>] prepare_to_wait_event+0x9f/0x6c0 WARNING: CPU: 2 PID: 4147 at kernel/sched/core.c:10099 __might_sleep+0x12f/0x160 mutex lock is not needed in ksmbd_durable_scavenger_alive().

In the Linux kernel, the following vulnerability has been resolved: USB: gadget: f_midi: f_midi_complete to call queue_work When using USB MIDI, a lock is attempted to be acquired twice through a re-entrant call to f_midi_transmit, causing a deadlock. Fix it by using queue_work() to schedule the inner f_midi_transmit() via a high priority work queue from the completion handler.

tip on multiple BSD-based operating systems allows local users to cause a denial of service (execution prevention) by using flock() to lock the /var/log/acculog file.

In the Linux kernel, the following vulnerability has been resolved: nvdimm: Fix firmware activation deadlock scenarios Lockdep reports the following deadlock scenarios for CXL root device power-management, device_prepare(), operations, and device_shutdown() operations for 'nd_region' devices: Chain exists of: &nvdimm_region_key --> &nvdimm_bus->reconfig_mutex --> system_transition_mutex Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(system_transition_mutex); lock(&nvdimm_bus->reconfig_mutex); lock(system_transition_mutex); lock(&nvdimm_region_key); Chain exists of: &cxl_nvdimm_bridge_key --> acpi_scan_lock --> &cxl_root_key Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&cxl_root_key); lock(acpi_scan_lock); lock(&cxl_root_key); lock(&cxl_nvdimm_bridge_key); These stem from holding nvdimm_bus_lock() over hibernate_quiet_exec() which walks the entire system device topology taking device_lock() along the way. The nvdimm_bus_lock() is protecting against unregistration, multiple simultaneous ops callers, and preventing activate_show() from racing activate_store(). For the first 2, the lock is redundant. Unregistration already flushes all ops users, and sysfs already prevents multiple threads to be active in an ops handler at the same time. For the last userspace should already be waiting for its last activate_store() to complete, and does not need activate_show() to flush the write side, so this lock usage can be deleted in these attributes.

In the Linux kernel, the following vulnerability has been resolved: ath11k: Fix frames flush failure caused by deadlock We are seeing below warnings: kernel: [25393.301506] ath11k_pci 0000:01:00.0: failed to flush mgmt transmit queue 0 kernel: [25398.421509] ath11k_pci 0000:01:00.0: failed to flush mgmt transmit queue 0 kernel: [25398.421831] ath11k_pci 0000:01:00.0: dropping mgmt frame for vdev 0, is_started 0 this means ath11k fails to flush mgmt. frames because wmi_mgmt_tx_work has no chance to run in 5 seconds. By setting /proc/sys/kernel/hung_task_timeout_secs to 20 and increasing ATH11K_FLUSH_TIMEOUT to 50 we get below warnings: kernel: [ 120.763160] INFO: task wpa_supplicant:924 blocked for more than 20 seconds. kernel: [ 120.763169] Not tainted 5.10.90 #12 kernel: [ 120.763177] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kernel: [ 120.763186] task:wpa_supplicant state:D stack: 0 pid: 924 ppid: 1 flags:0x000043a0 kernel: [ 120.763201] Call Trace: kernel: [ 120.763214] __schedule+0x785/0x12fa kernel: [ 120.763224] ? lockdep_hardirqs_on_prepare+0xe2/0x1bb kernel: [ 120.763242] schedule+0x7e/0xa1 kernel: [ 120.763253] schedule_timeout+0x98/0xfe kernel: [ 120.763266] ? run_local_timers+0x4a/0x4a kernel: [ 120.763291] ath11k_mac_flush_tx_complete+0x197/0x2b1 [ath11k 13c3a9bf37790f4ac8103b3decf7ab4008ac314a] kernel: [ 120.763306] ? init_wait_entry+0x2e/0x2e kernel: [ 120.763343] __ieee80211_flush_queues+0x167/0x21f [mac80211 335da900954f1c5ea7f1613d92088ce83342042c] kernel: [ 120.763378] __ieee80211_recalc_idle+0x105/0x125 [mac80211 335da900954f1c5ea7f1613d92088ce83342042c] kernel: [ 120.763411] ieee80211_recalc_idle+0x14/0x27 [mac80211 335da900954f1c5ea7f1613d92088ce83342042c] kernel: [ 120.763441] ieee80211_free_chanctx+0x77/0xa2 [mac80211 335da900954f1c5ea7f1613d92088ce83342042c] kernel: [ 120.763473] __ieee80211_vif_release_channel+0x100/0x131 [mac80211 335da900954f1c5ea7f1613d92088ce83342042c] kernel: [ 120.763540] ieee80211_vif_release_channel+0x66/0x81 [mac80211 335da900954f1c5ea7f1613d92088ce83342042c] kernel: [ 120.763572] ieee80211_destroy_auth_data+0xa3/0xe6 [mac80211 335da900954f1c5ea7f1613d92088ce83342042c] kernel: [ 120.763612] ieee80211_mgd_deauth+0x178/0x29b [mac80211 335da900954f1c5ea7f1613d92088ce83342042c] kernel: [ 120.763654] cfg80211_mlme_deauth+0x1a8/0x22c [cfg80211 8945aa5bc2af5f6972336665d8ad6f9c191ad5be] kernel: [ 120.763697] nl80211_deauthenticate+0xfa/0x123 [cfg80211 8945aa5bc2af5f6972336665d8ad6f9c191ad5be] kernel: [ 120.763715] genl_rcv_msg+0x392/0x3c2 kernel: [ 120.763750] ? nl80211_associate+0x432/0x432 [cfg80211 8945aa5bc2af5f6972336665d8ad6f9c191ad5be] kernel: [ 120.763782] ? nl80211_associate+0x432/0x432 [cfg80211 8945aa5bc2af5f6972336665d8ad6f9c191ad5be] kernel: [ 120.763802] ? genl_rcv+0x36/0x36 kernel: [ 120.763814] netlink_rcv_skb+0x89/0xf7 kernel: [ 120.763829] genl_rcv+0x28/0x36 kernel: [ 120.763840] netlink_unicast+0x179/0x24b kernel: [ 120.763854] netlink_sendmsg+0x393/0x401 kernel: [ 120.763872] sock_sendmsg+0x72/0x76 kernel: [ 120.763886] ____sys_sendmsg+0x170/0x1e6 kernel: [ 120.763897] ? copy_msghdr_from_user+0x7a/0xa2 kernel: [ 120.763914] ___sys_sendmsg+0x95/0xd1 kernel: [ 120.763940] __sys_sendmsg+0x85/0xbf kernel: [ 120.763956] do_syscall_64+0x43/0x55 kernel: [ 120.763966] entry_SYSCALL_64_after_hwframe+0x44/0xa9 kernel: [ 120.763977] RIP: 0033:0x79089f3fcc83 kernel: [ 120.763986] RSP: 002b:00007ffe604f0508 EFLAGS: 00000246 ORIG_RAX: 000000000000002e kernel: [ 120.763997] RAX: ffffffffffffffda RBX: 000059b40e987690 RCX: 000079089f3fcc83 kernel: [ 120.764006] RDX: 0000000000000000 RSI: 00007ffe604f0558 RDI: 0000000000000009 kernel: [ 120.764014] RBP: 00007ffe604f0540 R08: 0000000000000004 R09: 0000000000400000 kernel: [ 120.764023] R10: 00007ffe604f0638 R11: 0000000000000246 R12: 000059b40ea04980 kernel: [ 120.764032] R13: 00007ffe604 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: drivers: staging: rtl8723bs: Fix deadlock in rtw_surveydone_event_callback() There is a deadlock in rtw_surveydone_event_callback(), which is shown below: (Thread 1) | (Thread 2) | _set_timer() rtw_surveydone_event_callback()| mod_timer() spin_lock_bh() //(1) | (wait a time) ... | rtw_scan_timeout_handler() del_timer_sync() | spin_lock_bh() //(2) (wait timer to stop) | ... We hold pmlmepriv->lock in position (1) of thread 1 and use del_timer_sync() to wait timer to stop, but timer handler also need pmlmepriv->lock in position (2) of thread 2. As a result, rtw_surveydone_event_callback() will block forever. This patch extracts del_timer_sync() from the protection of spin_lock_bh(), which could let timer handler to obtain the needed lock. What`s more, we change spin_lock_bh() in rtw_scan_timeout_handler() to spin_lock_irq(). Otherwise, spin_lock_bh() will also cause deadlock() in timer handler.

In the Linux kernel, the following vulnerability has been resolved: block: Fix potential deadlock in blk_ia_range_sysfs_show() When being read, a sysfs attribute is already protected against removal with the kobject node active reference counter. As a result, in blk_ia_range_sysfs_show(), there is no need to take the queue sysfs lock when reading the value of a range attribute. Using the queue sysfs lock in this function creates a potential deadlock situation with the disk removal, something that a lockdep signals with a splat when the device is removed: [ 760.703551] Possible unsafe locking scenario: [ 760.703551] [ 760.703554] CPU0 CPU1 [ 760.703556] ---- ---- [ 760.703558] lock(&q->sysfs_lock); [ 760.703565] lock(kn->active#385); [ 760.703573] lock(&q->sysfs_lock); [ 760.703579] lock(kn->active#385); [ 760.703587] [ 760.703587] *** DEADLOCK *** Solve this by removing the mutex_lock()/mutex_unlock() calls from blk_ia_range_sysfs_show().

The handle_stop_signal function in signal.c in Linux kernel 2.6.11 up to other versions before 2.6.13 and 2.6.12.6 allows local users to cause a denial of service (deadlock) by sending a SIGKILL to a real-time threaded process while it is performing a core dump.

In the Linux kernel, the following vulnerability has been resolved: RDMA/ib_srp: Fix a deadlock Remove the flush_workqueue(system_long_wq) call since flushing system_long_wq is deadlock-prone and since that call is redundant with a preceding cancel_work_sync()

In the Linux kernel, the following vulnerability has been resolved: VMCI: Use threaded irqs instead of tasklets The vmci_dispatch_dgs() tasklet function calls vmci_read_data() which uses wait_event() resulting in invalid sleep in an atomic context (and therefore potentially in a deadlock). Use threaded irqs to fix this issue and completely remove usage of tasklets. [ 20.264639] BUG: sleeping function called from invalid context at drivers/misc/vmw_vmci/vmci_guest.c:145 [ 20.264643] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 762, name: vmtoolsd [ 20.264645] preempt_count: 101, expected: 0 [ 20.264646] RCU nest depth: 0, expected: 0 [ 20.264647] 1 lock held by vmtoolsd/762: [ 20.264648] #0: ffff0000874ae440 (sk_lock-AF_VSOCK){+.+.}-{0:0}, at: vsock_connect+0x60/0x330 [vsock] [ 20.264658] Preemption disabled at: [ 20.264659] [<ffff80000151d7d8>] vmci_send_datagram+0x44/0xa0 [vmw_vmci] [ 20.264665] CPU: 0 PID: 762 Comm: vmtoolsd Not tainted 5.19.0-0.rc8.20220727git39c3c396f813.60.fc37.aarch64 #1 [ 20.264667] Hardware name: VMware, Inc. VBSA/VBSA, BIOS VEFI 12/31/2020 [ 20.264668] Call trace: [ 20.264669] dump_backtrace+0xc4/0x130 [ 20.264672] show_stack+0x24/0x80 [ 20.264673] dump_stack_lvl+0x88/0xb4 [ 20.264676] dump_stack+0x18/0x34 [ 20.264677] __might_resched+0x1a0/0x280 [ 20.264679] __might_sleep+0x58/0x90 [ 20.264681] vmci_read_data+0x74/0x120 [vmw_vmci] [ 20.264683] vmci_dispatch_dgs+0x64/0x204 [vmw_vmci] [ 20.264686] tasklet_action_common.constprop.0+0x13c/0x150 [ 20.264688] tasklet_action+0x40/0x50 [ 20.264689] __do_softirq+0x23c/0x6b4 [ 20.264690] __irq_exit_rcu+0x104/0x214 [ 20.264691] irq_exit_rcu+0x1c/0x50 [ 20.264693] el1_interrupt+0x38/0x6c [ 20.264695] el1h_64_irq_handler+0x18/0x24 [ 20.264696] el1h_64_irq+0x68/0x6c [ 20.264697] preempt_count_sub+0xa4/0xe0 [ 20.264698] _raw_spin_unlock_irqrestore+0x64/0xb0 [ 20.264701] vmci_send_datagram+0x7c/0xa0 [vmw_vmci] [ 20.264703] vmci_datagram_dispatch+0x84/0x100 [vmw_vmci] [ 20.264706] vmci_datagram_send+0x2c/0x40 [vmw_vmci] [ 20.264709] vmci_transport_send_control_pkt+0xb8/0x120 [vmw_vsock_vmci_transport] [ 20.264711] vmci_transport_connect+0x40/0x7c [vmw_vsock_vmci_transport] [ 20.264713] vsock_connect+0x278/0x330 [vsock] [ 20.264715] __sys_connect_file+0x8c/0xc0 [ 20.264718] __sys_connect+0x84/0xb4 [ 20.264720] __arm64_sys_connect+0x2c/0x3c [ 20.264721] invoke_syscall+0x78/0x100 [ 20.264723] el0_svc_common.constprop.0+0x68/0x124 [ 20.264724] do_el0_svc+0x38/0x4c [ 20.264725] el0_svc+0x60/0x180 [ 20.264726] el0t_64_sync_handler+0x11c/0x150 [ 20.264728] el0t_64_sync+0x190/0x194

In the Linux kernel, the following vulnerability has been resolved: f2fs: initialize locks earlier in f2fs_fill_super() syzbot is reporting lockdep warning at f2fs_handle_error() [1], for spin_lock(&sbi->error_lock) is called before spin_lock_init() is called. For safe locking in error handling, move initialization of locks (and obvious structures) in f2fs_fill_super() to immediately after memory allocation.

In the Linux kernel, the following vulnerability has been resolved: pds_core: Fix pdsc_check_pci_health function to use work thread When the driver notices fw_status == 0xff it tries to perform a PCI reset on itself via pci_reset_function() in the context of the driver's health thread. However, pdsc_reset_prepare calls pdsc_stop_health_thread(), which attempts to stop/flush the health thread. This results in a deadlock because the stop/flush will never complete since the driver called pci_reset_function() from the health thread context. Fix by changing the pdsc_check_pci_health_function() to queue a newly introduced pdsc_pci_reset_thread() on the pdsc's work queue. Unloading the driver in the fw_down/dead state uncovered another issue, which can be seen in the following trace: WARNING: CPU: 51 PID: 6914 at kernel/workqueue.c:1450 __queue_work+0x358/0x440 [...] RIP: 0010:__queue_work+0x358/0x440 [...] Call Trace: <TASK> ? __warn+0x85/0x140 ? __queue_work+0x358/0x440 ? report_bug+0xfc/0x1e0 ? handle_bug+0x3f/0x70 ? exc_invalid_op+0x17/0x70 ? asm_exc_invalid_op+0x1a/0x20 ? __queue_work+0x358/0x440 queue_work_on+0x28/0x30 pdsc_devcmd_locked+0x96/0xe0 [pds_core] pdsc_devcmd_reset+0x71/0xb0 [pds_core] pdsc_teardown+0x51/0xe0 [pds_core] pdsc_remove+0x106/0x200 [pds_core] pci_device_remove+0x37/0xc0 device_release_driver_internal+0xae/0x140 driver_detach+0x48/0x90 bus_remove_driver+0x6d/0xf0 pci_unregister_driver+0x2e/0xa0 pdsc_cleanup_module+0x10/0x780 [pds_core] __x64_sys_delete_module+0x142/0x2b0 ? syscall_trace_enter.isra.18+0x126/0x1a0 do_syscall_64+0x3b/0x90 entry_SYSCALL_64_after_hwframe+0x72/0xdc RIP: 0033:0x7fbd9d03a14b [...] Fix this by preventing the devcmd reset if the FW is not running.

In the Linux kernel, the following vulnerability has been resolved: driver core: fix deadlock in __device_attach In __device_attach function, The lock holding logic is as follows: ... __device_attach device_lock(dev) // get lock dev async_schedule_dev(__device_attach_async_helper, dev); // func async_schedule_node async_schedule_node_domain(func) entry = kzalloc(sizeof(struct async_entry), GFP_ATOMIC); /* when fail or work limit, sync to execute func, but __device_attach_async_helper will get lock dev as well, which will lead to A-A deadlock. */ if (!entry || atomic_read(&entry_count) > MAX_WORK) { func; else queue_work_node(node, system_unbound_wq, &entry->work) device_unlock(dev) As shown above, when it is allowed to do async probes, because of out of memory or work limit, async work is not allowed, to do sync execute instead. it will lead to A-A deadlock because of __device_attach_async_helper getting lock dev. To fix the deadlock, move the async_schedule_dev outside device_lock, as we can see, in async_schedule_node_domain, the parameter of queue_work_node is system_unbound_wq, so it can accept concurrent operations. which will also not change the code logic, and will not lead to deadlock.

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix deadlock between concurrent dio writes when low on free data space When reserving data space for a direct IO write we can end up deadlocking if we have multiple tasks attempting a write to the same file range, there are multiple extents covered by that file range, we are low on available space for data and the writes don't expand the inode's i_size. The deadlock can happen like this: 1) We have a file with an i_size of 1M, at offset 0 it has an extent with a size of 128K and at offset 128K it has another extent also with a size of 128K; 2) Task A does a direct IO write against file range [0, 256K), and because the write is within the i_size boundary, it takes the inode's lock (VFS level) in shared mode; 3) Task A locks the file range [0, 256K) at btrfs_dio_iomap_begin(), and then gets the extent map for the extent covering the range [0, 128K). At btrfs_get_blocks_direct_write(), it creates an ordered extent for that file range ([0, 128K)); 4) Before returning from btrfs_dio_iomap_begin(), it unlocks the file range [0, 256K); 5) Task A executes btrfs_dio_iomap_begin() again, this time for the file range [128K, 256K), and locks the file range [128K, 256K); 6) Task B starts a direct IO write against file range [0, 256K) as well. It also locks the inode in shared mode, as it's within the i_size limit, and then tries to lock file range [0, 256K). It is able to lock the subrange [0, 128K) but then blocks waiting for the range [128K, 256K), as it is currently locked by task A; 7) Task A enters btrfs_get_blocks_direct_write() and tries to reserve data space. Because we are low on available free space, it triggers the async data reclaim task, and waits for it to reserve data space; 8) The async reclaim task decides to wait for all existing ordered extents to complete (through btrfs_wait_ordered_roots()). It finds the ordered extent previously created by task A for the file range [0, 128K) and waits for it to complete; 9) The ordered extent for the file range [0, 128K) can not complete because it blocks at btrfs_finish_ordered_io() when trying to lock the file range [0, 128K). This results in a deadlock, because: - task B is holding the file range [0, 128K) locked, waiting for the range [128K, 256K) to be unlocked by task A; - task A is holding the file range [128K, 256K) locked and it's waiting for the async data reclaim task to satisfy its space reservation request; - the async data reclaim task is waiting for ordered extent [0, 128K) to complete, but the ordered extent can not complete because the file range [0, 128K) is currently locked by task B, which is waiting on task A to unlock file range [128K, 256K) and task A waiting on the async data reclaim task. This results in a deadlock between 4 task: task A, task B, the async data reclaim task and the task doing ordered extent completion (a work queue task). This type of deadlock can sporadically be triggered by the test case generic/300 from fstests, and results in a stack trace like the following: [12084.033689] INFO: task kworker/u16:7:123749 blocked for more than 241 seconds. [12084.034877] Not tainted 5.18.0-rc2-btrfs-next-115 #1 [12084.035562] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [12084.036548] task:kworker/u16:7 state:D stack: 0 pid:123749 ppid: 2 flags:0x00004000 [12084.036554] Workqueue: btrfs-flush_delalloc btrfs_work_helper [btrfs] [12084.036599] Call Trace: [12084.036601] <TASK> [12084.036606] __schedule+0x3cb/0xed0 [12084.036616] schedule+0x4e/0xb0 [12084.036620] btrfs_start_ordered_extent+0x109/0x1c0 [btrfs] [12084.036651] ? prepare_to_wait_exclusive+0xc0/0xc0 [12084.036659] btrfs_run_ordered_extent_work+0x1a/0x30 [btrfs] [12084.036688] btrfs_work_helper+0xf8/0x400 [btrfs] [12084.0367 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: drivers: staging: rtl8192e: Fix deadlock in rtllib_beacons_stop() There is a deadlock in rtllib_beacons_stop(), which is shown below: (Thread 1) | (Thread 2) | rtllib_send_beacon() rtllib_beacons_stop() | mod_timer() spin_lock_irqsave() //(1) | (wait a time) ... | rtllib_send_beacon_cb() del_timer_sync() | spin_lock_irqsave() //(2) (wait timer to stop) | ... We hold ieee->beacon_lock in position (1) of thread 1 and use del_timer_sync() to wait timer to stop, but timer handler also need ieee->beacon_lock in position (2) of thread 2. As a result, rtllib_beacons_stop() will block forever. This patch extracts del_timer_sync() from the protection of spin_lock_irqsave(), which could let timer handler to obtain the needed lock.