The Autonomic Networking Infrastructure (ANI) implementation in Cisco IOS 12.2, 12.4, 15.0, 15.2, 15.3, and 15.4 and IOS XE 3.10.xS through 3.13.xS before 3.13.1S allows remote attackers to cause a denial of service (device reload) via spoofed AN messages, aka Bug ID CSCup62315.

Cisco IOS XE before 3.7.5S on ASR 1000 devices does not properly handle route adjacencies, which allows remote attackers to cause a denial of service (device hang) via crafted IP packets, aka Bug ID CSCub31873.

The Layer 4 Redirect (L4R) feature in Cisco IOS XE 2.x and 3.x before 3.10.4S, 3.11 before 3.11.3S, 3.12 before 3.12.2S, 3.13 before 3.13.1S, 3.14 before 3.14.0S, and 3.15 before 3.15.0S allows remote attackers to cause a denial of service (device reload) via malformed (1) IPv4 or (2) IPv6 packets, aka Bug ID CSCuq59131.

Cisco Videoscape Distribution Suite Service Broker (aka VDS-SB), when a VDSM configuration on UCS is used, and Videoscape Distribution Suite for Internet Streaming (aka VDS-IS or CDS-IS) before 3.3.1 R7 and 4.x before 4.0.0 R4 allow remote attackers to cause a denial of service (device reload) via a crafted HTTP request, aka Bug IDs CSCus79834 and CSCuu63409.

The XML parser in Cisco Adaptive Security Appliance (ASA) Software 8.4 before 8.4(7.28), 8.6 before 8.6(1.17), 9.0 before 9.0(4.33), 9.1 before 9.1(6), 9.2 before 9.2(3.4), and 9.3 before 9.3(3), when Clientless SSL VPN, AnyConnect SSL VPN, or AnyConnect IKEv2 VPN is used, allows remote attackers to cause a denial of service (VPN outage or device reload) via a crafted XML document, aka Bug ID CSCus95290.

The high-speed logging (HSL) feature in Cisco IOS XE 2.x and 3.x before 3.10.4S, 3.11 before 3.11.3S, 3.12 before 3.12.1S, 3.13 before 3.13.0S, 3.14 before 3.14.0S, and 3.15 before 3.15.0S allows remote attackers to cause a denial of service (device reload) via large IP packets that require NAT and HSL processing after fragmentation, aka Bug ID CSCuo25741.

Cisco IOS 12.2, 12.4, 15.0, 15.2, and 15.3 allows remote attackers to cause a denial of service (device reload) via malformed Common Industrial Protocol (CIP) UDP packets, aka Bug ID CSCum98371.

The Service Discovery Gateway (aka mDNS Gateway) in Cisco IOS 12.2, 12.4, 15.0, 15.1, 15.2, 15.3, and 15.4 and IOS XE 3.9.xS and 3.10.xS before 3.10.4S, 3.11.xS before 3.11.3S, 3.12.xS before 3.12.2S, and 3.13.xS before 3.13.1S allows remote attackers to cause a denial of service (device reload) by sending malformed mDNS UDP packets over (1) IPv4 or (2) IPv6, aka Bug ID CSCup70579.

The virtualization layer in Cisco ASA FirePOWER Software before 5.3.1.2 and 5.4.x before 5.4.0.1 and ASA Context-Aware (CX) Software before 9.3.2.1-9 allows remote attackers to cause a denial of service (device reload) by rapidly sending crafted packets to the management interface, aka Bug IDs CSCus11007 and CSCun56954.

The Common Flow Table (CFT) feature in Cisco IOS XE 3.6 and 3.7 before 3.7.1S, 3.8 before 3.8.0S, 3.9 before 3.9.0S, 3.10 before 3.10.0S, 3.11 before 3.11.0S, 3.12 before 3.12.0S, 3.13 before 3.13.0S, 3.14 before 3.14.0S, and 3.15 before 3.15.0S, when MMON or NBAR is enabled, allows remote attackers to cause a denial of service (device reload) via malformed IPv6 packets with IPv4 UDP encapsulation, aka Bug ID CSCua79665.

Cisco IOS 12.2, 12.4, 15.0, 15.1, 15.2, 15.3, and 15.4 and IOS XE 2.5.x, 2.6.x, 3.1.xS through 3.12.xS before 3.12.3S, 3.2.xE through 3.7.xE before 3.7.1E, 3.3.xSG, 3.4.xSG, and 3.13.xS before 3.13.2S allow remote attackers to cause a denial of service (device reload) by sending malformed IKEv2 packets over (1) IPv4 or (2) IPv6, aka Bug ID CSCum36951.

The Session Description Protocol (SDP) implementation in Cisco TelePresence Video Communication Server (VCS) and Cisco Expressway before X8.2 and Cisco TelePresence Conductor before XC2.4 allows remote attackers to cause a denial of service (mishandled exception and device reload) via a crafted media description, aka Bug IDs CSCus96593 and CSCun73192.

A vulnerability in the TACACS+ client subsystem of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause an affected device to reload, resulting in a denial of service (DoS) condition. The vulnerability is due to improper handling of crafted TACACS+ response packets by the affected software. An attacker could exploit this vulnerability by injecting a crafted TACACS+ packet into an existing TACACS+ session between an affected device and a TACACS+ server or by impersonating a known, valid TACACS+ server and sending a crafted TACACS+ packet to an affected device when establishing a connection to the device. To exploit this vulnerability by using either method, the attacker must know the shared TACACS+ secret and the crafted packet must be sent in response to a TACACS+ request from a TACACS+ client. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition.

Cisco ONS 15310-CL, 15310-MA, 15327, 15454, 15454 SDH, and 15600 with software 7.0.2 through 7.0.6, 7.2.2, 8.0.x, 8.5.1, and 8.5.2 allows remote attackers to cause a denial of service (control-card reset) via a crafted TCP session.

A vulnerability in the User Data Services (UDS) API of Cisco Unified Communications Manager (Unified CM) could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on the management GUI. The vulnerability is due to improper validation of input parameters in the UDS API requests. An attacker could exploit this vulnerability by sending a crafted request to the UDS API of an affected device. A successful exploit could allow the attacker to make the A Cisco DB service quit unexpectedly, preventing admin access to the Unified CM management GUI. Manual intervention may be required to restore normal operation. Software versions 10.5, 11.5, 12.0, 12.5 are affected.

A vulnerability in the Cisco Fabric Services component of Cisco NX-OS Software could allow an unauthenticated, remote attacker to cause process crashes, which can result in a denial of service (DoS) condition on an affected system. The vulnerability is due to insufficient validation of TCP packets when processed by the Cisco Fabric Services over IP (CFSoIP) feature. An attacker could exploit this vulnerability by sending a malicious Cisco Fabric Services TCP packet to an affected device. A successful exploit could allow the attacker to cause process crashes, resulting in a device reload and a DoS condition. Note: There are three distribution methods that can be configured for Cisco Fabric Services. This vulnerability affects only distribution method CFSoIP, which is disabled by default. See the Details section for more information.

Cisco IOS 12.2 and 12.4, when NAT Skinny Call Control Protocol (SCCP) Fragmentation Support is enabled, allows remote attackers to cause a denial of service (device reload) via segmented SCCP messages, aka CSCsg22426, a different vulnerability than CVE-2008-3811.

Cisco TelePresence TC Software 4.x and 5.x and TE Software 4.x and 6.0 allow remote attackers to cause a denial of service (memory consumption) via crafted H.225 packets, aka Bug ID CSCtq78849.

The H.225 subsystem in Cisco TelePresence System MXP Series Software before F9.3.1 allows remote attackers to cause a denial of service (device reload) via crafted packets, aka Bug ID CSCtq78722.

The SIP implementation in Cisco TelePresence TC Software 4.x and 5.x and TE Software 4.x allows remote attackers to cause a denial of service (device reload) via crafted SIP packets, aka Bug ID CSCua64961.

The SIP implementation in Cisco TelePresence TC Software 4.x and 5.x and TE Software 4.x and 6.0 allows remote attackers to cause a denial of service (device reload) via crafted SIP packets, aka Bug ID CSCua86589.

Cisco TelePresence System MXP Series Software before F9.3.1 allows remote attackers to cause a denial of service (device reload) via crafted SIP packets, aka Bug ID CSCty45720.

The SIP implementation in Cisco TelePresence TC Software 4.x and 5.x and TE Software 4.x and 6.0 allows remote attackers to cause a denial of service (device reload) via crafted SIP packets, aka Bug ID CSCuj94651.

The EnergyWise module in Cisco IOS 12.2, 15.0, 15.1, 15.2, and 15.4 and IOS XE 3.2.xXO, 3.3.xSG, 3.4.xSG, and 3.5.xE before 3.5.3E allows remote attackers to cause a denial of service (device reload) via a crafted IPv4 packet, aka Bug ID CSCup52101.

The H.225 subsystem in Cisco TelePresence System MXP Series Software before F9.3.1 allows remote attackers to cause a denial of service (device reload) via crafted packets, aka Bug ID CSCty45745.

The H.225 subsystem in Cisco TelePresence System MXP Series Software before F9.3.1 allows remote attackers to cause a denial of service (device reload) via crafted packets, aka Bug ID CSCty45731.

The SIP implementation in Cisco TelePresence TC Software 4.x and 5.x and TE Software 4.x and 6.0 allows remote attackers to cause a denial of service (device reload) via crafted SIP packets, aka Bug ID CSCud29566.

Cisco IOS 12.2 and 15.0 through 15.3 and IOS XE 3.2 through 3.7 before 3.7.5S and 3.8 through 3.10 before 3.10.1S allow remote attackers to cause a denial of service (device reload) via a malformed IKEv2 packet, aka Bug ID CSCui88426.

A vulnerability in the Cisco Encrypted Traffic Analytics (ETA) feature of Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition. The vulnerability is due to a logic error that exists when handling a malformed incoming packet, leading to access to an internal data structure after it has been freed. An attacker could exploit this vulnerability by sending crafted, malformed IP packets to an affected device. A successful exploit could allow the attacker to cause an affected device to reload, resulting in a DoS condition.

A vulnerability in the ISDN functions of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause the device to reload. The vulnerability is due to incorrect processing of specific values in the Q.931 information elements. An attacker could exploit this vulnerability by calling the affected device with specific Q.931 information elements being present. An exploit could allow the attacker to cause the device to reload, resulting in a denial of service (DoS) condition on an affected device.

The HTTP server in Cisco Unified IP Phone 7935 and 7936 running SCCP firmware allows remote attackers to cause a denial of service (reboot) via a crafted HTTP request.

A vulnerability in the Network-Based Application Recognition (NBAR) feature of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause an affected device to reload. This vulnerability are due to a parsing issue on DNS packets. An attacker could exploit this vulnerability by sending crafted DNS packets through routers that are running an affected version and have NBAR enabled. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a denial of service (DoS) condition.

The TCP Input module in Cisco IOS 12.2 through 12.4 and 15.0 through 15.4, when NAT is used, allows remote attackers to cause a denial of service (memory consumption or device reload) via crafted TCP packets, aka Bug IDs CSCuh33843 and CSCuj41494.

Cisco IOS 15.3M before 15.3(3)M2 and IOS XE 3.10.xS before 3.10.2S allow remote attackers to cause a denial of service (device reload) via crafted SIP messages, aka Bug ID CSCug45898.

Cisco IOS 15.1 through 15.3 and IOS XE 3.3 and 3.5 before 3.5.2E; 3.7 before 3.7.5S; and 3.8, 3.9, and 3.10 before 3.10.2S allow remote attackers to cause a denial of service (I/O memory consumption and device reload) via a malformed IPv6 packet, aka Bug ID CSCui59540.

A vulnerability in the Border Gateway Protocol (BGP) implementation of Cisco NX-OS Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition due to the device unexpectedly reloading. The vulnerability is due to incomplete input validation of the BGP update messages. An attacker could exploit this vulnerability by sending a crafted BGP update message to the targeted device. An exploit could allow the attacker to cause the switch to reload unexpectedly. The Cisco implementation of the BGP protocol only accepts incoming BGP traffic from explicitly defined peers. To exploit this vulnerability, an attacker must be able to send the malicious packets over a TCP connection that appears to come from a trusted BGP peer or inject malformed messages into the victim's BGP network. This would require obtaining information about the BGP peers in the affected system's trusted network. The vulnerability may be triggered when the router receives a malformed BGP message from a peer on an existing BGP session. At least one BGP neighbor session must be established for a router to be vulnerable. This vulnerability affects Nexus 2000 Series Switches, Nexus 3000 Series Switches, Nexus 3500 Platform Switches, Nexus 3600 Platform Switches, Nexus 5500 Platform Switches, Nexus 5600 Platform Switches, Nexus 6000 Series Switches, Nexus 7000 Series Switches, Nexus 7700 Series Switches, Nexus 9000 Series Fabric Switches in Application Centric Infrastructure (ACI) mode, Nexus 9000 Series Switches in standalone NX-OS mode, Nexus 9500 R-Series Line Cards and Fabric Modules. Cisco Bug IDs: CSCve79599, CSCve87784, CSCve91371, CSCve91387.

A vulnerability in the Transport Layer Security (TLS) library of Cisco Adaptive Security Appliance (ASA) Software and Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to trigger a reload of the affected device, resulting in a denial of service (DoS) condition. The vulnerability is due to insufficient validation of user-supplied input. An attacker could exploit this vulnerability by sending a malicious TLS message to an interface enabled for Secure Layer Socket (SSL) services on an affected device. Messages using SSL Version 3 (SSLv3) or SSL Version 2 (SSLv2) cannot be be used to exploit this vulnerability. An exploit could allow the attacker to cause a buffer underflow, triggering a crash on an affected device. This vulnerability affects Cisco ASA Software and Cisco FTD Software that is running on the following Cisco products: Adaptive Security Virtual Appliance (ASAv), Firepower Threat Defense Virtual (FTDv), Firepower 2100 Series Security Appliance. Cisco Bug IDs: CSCve18902, CSCve34335, CSCve38446.

A vulnerability in the web UI of Cisco FXOS and Cisco UCS Fabric Interconnect Software could allow an unauthenticated, remote attacker to cause a buffer overflow on an affected system. The vulnerability is due to incorrect input validation in the web UI. An attacker could exploit this vulnerability by sending a malicious HTTP or HTTPS packet directed to the physical management interface of an affected system. A successful exploit could allow the attacker to cause the process to crash and possibly reload the device, resulting in a denial of service (DoS) condition on the affected system. This vulnerability affects Firepower 4100 Series Next-Generation Firewall, Firepower 9300 Security Appliance, UCS 6200 Series Fabric Interconnects, UCS 6300 Series Fabric Interconnects. Cisco Bug IDs: CSCvb61398, CSCvb86799.

A vulnerability in the ingress packet processing functionality of the Cisco Virtualized Packet Core-Distributed Instance (VPC-DI) Software could allow an unauthenticated, remote attacker to cause both control function (CF) instances on an affected system to reload, resulting in a denial of service (DoS) condition. The vulnerability is due to insufficient handling of user-supplied data by the affected software. An attacker could exploit this vulnerability by sending malicious traffic to the internal distributed instance (DI) network address on an affected system. A successful exploit could allow the attacker to cause an unhandled error condition on the affected system, which would cause the CF instances to reload and consequently cause the entire VPC to reload, resulting in the disconnection of all subscribers and a DoS condition on the affected system. This vulnerability affects Cisco Virtualized Packet Core-Distributed Instance (VPC-DI) Software N4.0 through N5.5 with the Cisco StarOS operating system 19.2 through 21.3. Cisco Bug IDs: CSCve17656.

A vulnerability in the IPv6 subsystem of Cisco IOS XR Software Release 5.3.4 for the Cisco Aggregation Services Router (ASR) 9000 Series could allow an unauthenticated, remote attacker to trigger a reload of one or more Trident-based line cards, resulting in a denial of service (DoS) condition. The vulnerability is due to incorrect handling of IPv6 packets with a fragment header extension. An attacker could exploit this vulnerability by sending IPv6 packets designed to trigger the issue either to or through the Trident-based line card. A successful exploit could allow the attacker to trigger a reload of Trident-based line cards, resulting in a DoS during the period of time the line card takes to restart. This vulnerability affects Cisco Aggregation Services Router (ASR) 9000 Series when the following conditions are met: The router is running Cisco IOS XR Software Release 5.3.4, and the router has installed Trident-based line cards that have IPv6 configured. A software maintenance upgrade (SMU) has been made available that addresses this vulnerability. The fix has also been incorporated into service pack 7 for Cisco IOS XR Software Release 5.3.4. Cisco Bug IDs: CSCvg46800.

A vulnerability in the implementation of Point-to-Point Tunneling Protocol (PPTP) functionality in Cisco Aironet 1810, 1830, and 1850 Series Access Points could allow an unauthenticated, remote attacker to cause an affected device to reload, resulting in a denial of service (DoS) condition. The vulnerability is due to insufficient validation of Generic Routing Encapsulation (GRE) frames that pass through the data plane of an affected access point. An attacker could exploit this vulnerability by initiating a PPTP connection to an affected access point from a device that is registered to the same wireless network as the access point and sending a malicious GRE frame through the data plane of the access point. A successful exploit could allow the attacker to cause the NSS core process on the affected access point to crash, which would cause the access point to reload and result in a DoS condition. This vulnerability affects Cisco Aironet 1810, 1830, and 1850 Series Access Points that are running Cisco Mobility Express Software Release 8.4.100.0, 8.5.103.0, or 8.5.105.0 and are configured as a master, subordinate, or standalone access point. Cisco Bug IDs: CSCvf73890.

A vulnerability in the Internet Key Exchange Version 2 (IKEv2) module of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause a memory leak or a reload of an affected device that leads to a denial of service (DoS) condition. The vulnerability is due to incorrect processing of certain IKEv2 packets. An attacker could exploit this vulnerability by sending crafted IKEv2 packets to an affected device to be processed. A successful exploit could cause an affected device to continuously consume memory and eventually reload, resulting in a DoS condition. Cisco Bug IDs: CSCvf22394.

A vulnerability in the implementation of Internet Key Exchange Version 1 (IKEv1) functionality in Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause an affected device to reload, resulting in a denial of service (DoS) condition. The vulnerability is due to improper validation of specific IKEv1 packets. An attacker could exploit this vulnerability by sending crafted IKEv1 packets to an affected device during an IKE negotiation. A successful exploit could allow the attacker to cause an affected device to reload, resulting in a DoS condition. Cisco Bug IDs: CSCuj73916.

A vulnerability in the SM-1T3/E3 firmware on Cisco Second Generation Integrated Services Routers (ISR G2) and the Cisco 4451-X Integrated Services Router (ISR4451-X) could allow an unauthenticated, remote attacker to cause the ISR G2 Router or the SM-1T3/E3 module on the ISR4451-X to reload, resulting in a denial of service (DoS) condition on an affected device. The vulnerability is due to improper handling of user input. An attacker could exploit this vulnerability by first connecting to the SM-1T3/E3 module console and entering a string sequence. A successful exploit could allow the attacker to cause the ISR G2 Router or the SM-1T3/E3 module on the ISR4451-X to reload, resulting in a DoS condition on an affected device.

A vulnerability in the DHCP option 82 encapsulation functionality of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause an affected device to reload, resulting in a denial of service (DoS) condition. The vulnerability exists because the affected software performs incomplete input validation of option 82 information that it receives in DHCP Version 4 (DHCPv4) packets from DHCP relay agents. An attacker could exploit this vulnerability by sending a crafted DHCPv4 packet to an affected device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition. Cisco Bug IDs: CSCuh91645.

A vulnerability in the Precision Time Protocol (PTP) feature of Cisco Nexus 5500, 5600, and 6000 Series Switches running Cisco NX-OS Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. The vulnerability is due to a lack of protection against PTP frame flood attacks. An attacker could exploit this vulnerability by sending large streams of malicious IPv4 or IPv6 PTP traffic to the affected device. A successful exploit could allow the attacker to cause a DoS condition, impacting the traffic passing through the device.

A vulnerability in the Smart Install feature of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to trigger a reload of an affected device, resulting in a denial of service (DoS) condition. The vulnerability is due to improper validation of packet data. An attacker could exploit this vulnerability by sending a crafted packet to an affected device on TCP port 4786. Only Smart Install client switches are affected. Cisco devices that are configured as a Smart Install director are not affected by this vulnerability. Cisco Bug IDs: CSCvd40673.

A vulnerability in the DHCP option 82 encapsulation functionality of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause an affected device to reload, resulting in a denial of service (DoS) condition. The vulnerability exists because the affected software performs incomplete input validation of option 82 information that it receives in DHCP Version 4 (DHCPv4) packets from DHCP relay agents. An attacker could exploit this vulnerability by sending a crafted DHCPv4 packet to an affected device. A successful exploit could allow the attacker to cause a heap overflow condition on the affected device, which will cause the device to reload and result in a DoS condition. Cisco Bug IDs: CSCvg62730.

A vulnerability in the IPv6 processing code of Cisco IOS and IOS XE Software could allow an unauthenticated, remote attacker to cause the device to reload. The vulnerability is due to incorrect handling of specific IPv6 hop-by-hop options. An attacker could exploit this vulnerability by sending a malicious IPv6 packet to or through the affected device. A successful exploit could allow the attacker to cause the device to reload, resulting in a denial of service (DoS) condition on an affected device.