spice versions though 0.13 are vulnerable to out-of-bounds memory access when processing specially crafted messages from authenticated attacker to the spice server resulting into crash and/or server memory leak.
Stack-based buffer overflow in the reslist function in ntpq in NTP before 4.2.8p10 and 4.3.x before 4.3.94 allows remote servers have unspecified impact via a long flagstr variable in a restriction list response.
Multiple buffer overflows in the ctl_put* functions in NTP before 4.2.8p10 and 4.3.x before 4.3.94 allow remote authenticated users to have unspecified impact via a long variable.
A stack buffer overflow flaw was found in the Quick Emulator (QEMU) before 2.9 built with the Network Block Device (NBD) client support. The flaw could occur while processing server's response to a 'NBD_OPT_LIST' request. A malicious NBD server could use this issue to crash a remote NBD client resulting in DoS or potentially execute arbitrary code on client host with privileges of the QEMU process.
A Buffer Overflow issue was discovered in Asterisk Open Source 13 before 13.18.1, 14 before 14.7.1, and 15 before 15.1.1 and Certified Asterisk 13.13 before 13.13-cert7. No size checking is done when setting the user field for Party B on a CDR. Thus, it is possible for someone to use an arbitrarily large string and write past the end of the user field storage buffer. NOTE: this is different from CVE-2017-7617, which was only about the Party A buffer.
An issue was discovered on Securifi Almond, Almond+, and Almond 2015 devices with firmware AL-R096. The device provides a user with the capability of adding new routes to the device. It seems that the POST parameters passed in this request to set up routes on the device can be set in such a way that would result in overflowing the stack set up and allow an attacker to control the $ra register stored on the stack. If the firmware version AL-R096 is dissected using binwalk tool, we obtain a cpio-root archive which contains the filesystem set up on the device that contains all the binaries. The binary "goahead" is the one that has the vulnerable function that recieves the values sent by the POST request. If we open this binary in IDA-pro we will notice that this follows a MIPS little endian format. The function sub_00420F38 in IDA pro is identified to be receiving the values sent in the POST request. The POST parameter "gateway" allows to overflow the stack and control the $ra register after 1546 characters. The value from this post parameter is then copied on the stack at address 0x00421348 as shown below. This allows an attacker to provide the payload of his/her choice and finally take control of the device.
Stack buffer overflow in httpd in Asuswrt-Merlin firmware 380.67_0RT-AC5300 and earlier for ASUS devices and ASUS firmware for ASUS RT-AC5300, RT_AC1900P, RT-AC68U, RT-AC68P, RT-AC88U, RT-AC66U, RT-AC66U_B1, RT-AC58U, RT-AC56U, RT-AC55U, RT-AC52U, RT-AC51U, RT-N18U, RT-N66U, RT-N56U, RT-AC3200, RT-AC3100, RT_AC1200GU, RT_AC1200G, RT-AC1200, RT-AC53, RT-N12HP, RT-N12HP_B1, RT-N12D1, RT-N12+, RT_N12+_PRO, RT-N16, and RT-N300 devices allows remote attackers to execute arbitrary code on the router by sending a crafted http GET request packet that includes a long delete_offline_client parameter in the url.
Recently it was discovered as a part of the research on IoT devices in the most recent firmware for Shekar Endoscope that an attacker connected to the device Wi-Fi SSID can exploit a memory corruption issue and execute remote code on the device. This device acts as an Endoscope camera that allows its users to use it in various industrial systems and settings, car garages, and also in some cases in the medical clinics to get access to areas that are difficult for a human being to reach. Any breach of this system can allow an attacker to get access to video feed and pictures viewed by that user and might allow them to get a foot hold in air gapped networks especially in case of nation critical infrastructure/industries. The firmware contains binary uvc_stream that is the UDP daemon which is responsible for handling all the UDP requests that the device receives. The client application sends a UDP request to change the Wi-Fi name which contains the following format: "SETCMD0001+0002+[2 byte length of wifipassword]+[Wifipassword]. This request is handled by "control_Dev_thread" function which at address "0x00409AE4" compares the incoming request and determines if the 10th byte is 02 and if it is then it redirects to 0x0040A7D8, which calls the function "setwifipassword". The function "setwifipassword" uses a memcpy function but uses the length of the payload obtained by using strlen function as the third parameter which is the number of bytes to copy and this allows an attacker to overflow the function and control the $PC value.
Recently it was discovered as a part of the research on IoT devices in the most recent firmware for Shekar Endoscope that an attacker connected to the device Wi-Fi SSID can exploit a memory corruption issue and execute remote code on the device. This device acts as an Endoscope camera that allows its users to use it in various industrial systems and settings, car garages, and also in some cases in the medical clinics to get access to areas that are difficult for a human being to reach. Any breach of this system can allow an attacker to get access to video feed and pictures viewed by that user and might allow them to get a foot hold in air gapped networks especially in case of nation critical infrastructure/industries. The firmware contains binary uvc_stream that is the UDP daemon which is responsible for handling all the UDP requests that the device receives. The client application sends a UDP request to change the Wi-Fi name which contains the following format: "SETCMD0001+0001+[2 byte length of wifiname]+[Wifiname]. This request is handled by "control_Dev_thread" function which at address "0x00409AE0" compares the incoming request and determines if the 10th byte is 01 and if it is then it redirects to 0x0040A74C which calls the function "setwifiname". The function "setwifiname" uses a memcpy function but uses the length of the payload obtained by using strlen function as the third parameter which is the number of bytes to copy and this allows an attacker to overflow the function and control the $PC value.