A NULL Pointer Dereference vulnerability in Juniper Networks Junos OS Evolved on ACX7024, ACX7100-32C and ACX7100-48L allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). If a specific IPv4 UDP packet is received and sent to the Routing Engine (RE) packetio crashes and restarts which causes a momentary traffic interruption. Continued receipt of such packets will lead to a sustained DoS. This issue does not happen with IPv6 packets. This issue affects Juniper Networks Junos OS Evolved on ACX7024, ACX7100-32C and ACX7100-48L: * 21.4-EVO versions earlier than 21.4R3-S6-EVO; * 22.1-EVO versions earlier than 22.1R3-S5-EVO; * 22.2-EVO versions earlier than 22.2R2-S1-EVO, 22.2R3-EVO; * 22.3-EVO versions earlier than 22.3R2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions earlier than 21.4R1-EVO.

An Allocation of Resources Without Limits or Throttling vulnerability in the kernel of Juniper Networks Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). If a high rate of specific valid packets are processed by the routing engine (RE) this will lead to a loss of connectivity of the RE with other components of the chassis and thereby a complete and persistent system outage. Please note that a carefully designed lo0 firewall filter will block or limit these packets which should prevent this issue from occurring. The following log messages can be seen when this issue occurs: <host> kernel: nf_conntrack: nf_conntrack: table full, dropping packet This issue affects Juniper Networks Junos OS Evolved: * All versions earlier than 20.4R3-S7-EVO; * 21.2R1-EVO and later versions; * 21.4-EVO versions earlier than 21.4R3-S5-EVO; * 22.1-EVO versions earlier than 22.1R3-S2-EVO; * 22.2-EVO versions earlier than 22.2R3-EVO; * 22.3-EVO versions earlier than 22.3R2-EVO; * 22.4-EVO versions earlier than 22.4R2-EVO.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on SRX Series and NFX Series allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS). If an affected device receives specific valid traffic destined to the device, it will cause the PFE to crash and restart. Continued receipt and processing of this traffic will create a sustained DoS condition. This issue affects Junos OS on SRX Series: * 21.4 versions before 21.4R3-S7.9, * 22.1 versions before 22.1R3-S5.3, * 22.2 versions before 22.2R3-S4.11, * 22.3 versions before 22.3R3, * 22.4 versions before 22.4R3. This issue affects Junos OS on NFX Series: * 21.4 versions before 21.4R3-S8, * 22.1 versions after 22.1R1, * 22.2 versions before 22.2R3-S5, * 22.3 versions before 22.3R3, * 22.4 versions before 22.4R3. Junos OS versions prior to 21.4R1 are not affected by this issue.

An Improper Handling of Syntactically Invalid Structure vulnerability in Object Flooding Protocol (OFP) service of Juniper Networks Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). On all Junos OS Evolved platforms, when specific TCP packets are received on an open OFP port, the OFP crashes leading to a restart of Routine Engine (RE). Continuous receipt of these specific TCP packets will lead to a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS Evolved * All versions earlier than 21.2R3-S7-EVO; * 21.3 versions earlier than 21.3R3-S5-EVO ; * 21.4 versions earlier than 21.4R3-S5-EVO; * 22.1 versions earlier than 22.1R3-S4-EVO; * 22.2 versions earlier than 22.2R3-S3-EVO ; * 22.3 versions earlier than 22.3R3-EVO; * 22.4 versions earlier than 22.4R2-EVO, 22.4R3-EVO.

An Improper Validation of Syntactic Correctness of Input vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). If a BGP update is received over an established BGP session which contains a tunnel encapsulation attribute with a specifically malformed TLV, rpd will crash and restart. This issue affects Juniper Networks Junos OS: * 20.4 versions 20.4R1 and later versions earlier than 20.4R3-S9; * 21.2 versions earlier than 21.2R3-S7; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R3-S4; * 22.2 versions earlier than 22.2R3-S3; * 22.3 versions earlier than 22.3R3-S1; * 22.4 versions earlier than 22.4R3; * 23.2 versions earlier than 23.2R1-S2, 23.2R2; Junos OS Evolved: * 20.4-EVO versions 20.4R1-EVO and later versions earlier than 20.4R3-S9-EVO; * 21.2-EVO versions earlier than 21.2R3-S7-EVO; * 21.3-EVO versions earlier than 21.3R3-S5-EVO; * 21.4-EVO versions earlier than 21.4R3-S5-EVO; * 22.1-EVO versions earlier than 22.1R3-S4-EVO; * 22.2-EVO versions earlier than 22.2R3-S3-EVO; * 22.3-EVO versions earlier than 22.3R3-S1-EVO; * 22.4-EVO versions earlier than 22.4R3-EVO; * 23.2-EVO versions earlier than 23.2R1-S2-EVO, 23.2R2-EVO; This issue does not affect Juniper Networks * Junos OS versions earlier than 20.4R1; * Junos OS Evolved versions earlier than 20.4R1-EVO. This is a related but separate issue than the one described in JSA79095.

An Improper Check for Unusual or Exceptional Conditions vulnerability in Routing Protocol Daemon (RPD) of Juniper Networks Junos OS and Junos OS Evolved allows a network-based, unauthenticated attacker to cause rpd to crash, leading to Denial of Service (DoS). On all Junos OS and Junos OS Evolved platforms, when NETCONF and gRPC are enabled, and a specific query is executed via Dynamic Rendering (DREND), rpd will crash and restart. Continuous execution of this specific query will cause a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS * 22.2 versions earlier than 22.2R2-S2, 22.2R3; * 22.3 versions earlier than 22.3R2, 22.3R3. Juniper Networks Junos OS Evolved * 22.2 versions earlier than 22.2R2-S2-EVO, 22.2R3-EVO; * 22.3 versions earlier than 22.3R2-EVO, 22.3R3-EVO. This issue does not affect Juniper Networks: Junos OS versions earlier than 22.2R1; Junos OS Evolved versions earlier than 22.2R1-EVO.

An Improper Validation of Syntactic Correctness of Input vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). If an attacker sends high rate of specific ICMP traffic to a device with VXLAN configured, this causes a deadlock of the PFE and results in the device becoming unresponsive. A manual restart will be required to recover the device. This issue only affects EX4100, EX4400, EX4600, QFX5000 Series devices. This issue affects: Juniper Networks Junos OS * 21.4R3 versions earlier than 21.4R3-S4; * 22.1R3 versions earlier than 22.1R3-S3; * 22.2R2 versions earlier than 22.2R3-S1; * 22.3 versions earlier than 22.3R2-S2, 22.3R3; * 22.4 versions earlier than 22.4R2; * 23.1 versions earlier than 23.1R2.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the chassis management daemon (chassisd) of Juniper Networks Junos OS allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS). If an attempt is made to access specific sensors on platforms not supporting these sensors, either via GRPC or netconf, chassisd will crash and restart leading to a restart of all FPCs and thereby a complete outage. This issue affects Junos OS: * 21.4 versions from 21.4R3 before 21.4R3-S5, * 22.1 versions from 22.1R3 before 22.1R3-S4, * 22.2 versions from 22.2R2 before 22.2R3, * 22.3 versions from 22.3R1 before 22.3R2-S2, 22.3R3, * 22.4 versions from 22.4R1 before 22.4R2. This issue does not affect Junos OS versions earlier than 21.4.

A Heap-based Buffer Overflow vulnerability in the telemetry sensor process (sensord) of Juniper Networks Junos OS on MX240, MX480, MX960 platforms using MPC10E causes a steady increase in memory utilization, ultimately leading to a Denial of Service (DoS). When the device is subscribed to a specific subscription on Junos Telemetry Interface, a slow memory leak occurs and eventually all resources are consumed and the device becomes unresponsive. A manual reboot of the Line Card will be required to restore the device to its normal functioning.  This issue is only seen when telemetry subscription is active. The Heap memory utilization can be monitored using the following command:   > show system processes extensive The following command can be used to monitor the memory utilization of the specific sensor   > show system info | match sensord PID NAME MEMORY PEAK MEMORY %CPU THREAD-COUNT CORE-AFFINITY UPTIME 1986 sensord 877.57MB 877.57MB 2 4 0,2-15 7-21:41:32 This issue affects Junos OS:  * from 21.2R3-S5 before 21.2R3-S7,  * from 21.4R3-S4 before 21.4R3-S6,  * from 22.2R3 before 22.2R3-S4,  * from 22.3R2 before 22.3R3-S2,  * from 22.4R1 before 22.4R3,  * from 23.2R1 before 23.2R2.

An Uncontrolled Resource Consumption vulnerability in the aftmand process of Juniper Networks Junos OS Evolved allows an unauthenticated, network-based attacker to consume memory resources, resulting in a Denial of Service (DoS) condition. The processes do not recover on their own and must be manually restarted. This issue affects both IPv4 and IPv6.  Changes in memory usage can be monitored using the following CLI command: user@device> show system memory node <fpc slot> | grep evo-aftmann This issue affects Junos OS Evolved:  * All versions before 21.2R3-S8-EVO,  * 21.3 versions before 21.3R3-S5-EVO,  * 21.4 versions before 21.4R3-S5-EVO,  * 22.1 versions before 22.1R3-S4-EVO,  * 22.2 versions before 22.2R3-S4-EVO, * 22.3 versions before 22.3R3-S3-EVO, * 22.4 versions before 22.4R2-S2-EVO, 22.4R3-EVO,  * 23.2 versions before 23.2R1-S1-EVO, 23.2R2-EVO.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the routing protocol daemon (RPD) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network based attacker to cause a Denial of Service (DoS).  In a scenario where BGP Monitoring Protocol (BMP) is configured with rib-in pre-policy monitoring, receiving a BGP update with a specifically malformed AS PATH attribute over an established BGP session, can cause an RPD crash and restart. This issue affects: Junos OS:  * All versions before 21.2R3-S8, * 21.4 versions before 21.4R3-S8, * 22.2 versions before 22.2R3-S4, * 22.3 versions before 22.3R3-S3, * 22.4 versions before 22.4R3-S2, * 23.2 versions before 23.2R2-S1, * 23.4 versions before 23.4R1-S2, 23.4R2; Junos OS Evolved: * All versions before 21.2R3-S8-EVO, * 21.4 versions before 21.4R3-S8-EVO, * 22.2 versions before 22.2R3-S4-EVO, * 22.3 versions before 22.3R3-S3-EVO, * 22.4 versions before 22.4R3-S2-EVO, * 23.2 versions before 23.2R2-S1-EVO, * 23.4 versions before 23.4R1-S2-EVO, 23.4R2-EVO.

In broadband environments, including but not limited to Enhanced Subscriber Management, (CHAP, PPP, DHCP, etc.), on Juniper Networks Junos OS devices where RADIUS servers are configured for managing subscriber access and a subscriber is logged in and then requests to logout, the subscriber may be forced into a "Terminating" state by an attacker who is able to send spoofed messages appearing to originate from trusted RADIUS server(s) destined to the device in response to the subscriber's request. These spoofed messages cause the Junos OS General Authentication Service (authd) daemon to force the broadband subscriber into this "Terminating" state which the subscriber will not recover from thereby causing a Denial of Service (DoS) to the endpoint device. Once in the "Terminating" state, the endpoint subscriber will no longer be able to access the network. Restarting the authd daemon on the Junos OS device will temporarily clear the subscribers out of the "Terminating" state. As long as the attacker continues to send these spoofed packets and subscribers request to be logged out, the subscribers will be returned to the "Terminating" state thereby creating a persistent Denial of Service to the subscriber. An indicator of compromise may be seen by displaying the output of "show subscribers summary". The presence of subscribers in the "Terminating" state may indicate the issue is occurring. This issue affects: Juniper Networks Junos OS 17.3 versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S8, 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R1-S4, 19.4R3-S3; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S1; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2. This issue does not affect: Juniper Networks Junos OS 12.3 version 12.3R1 and later versions; 15.1 version 15.1R1 and later versions.

On Juniper Networks Junos OS and Junos OS Evolved devices, processing a specific UPDATE for an EBGP peer can lead to a routing process daemon (RPD) crash and restart. This issue occurs only when the device is receiving and processing the BGP UPDATE for an EBGP peer. This issue does not occur when the device is receiving and processing the BGP UPDATE for an IBGP peer. However, the offending BGP UPDATE can originally come from an EBGP peer, propagates through the network via IBGP peers without causing crash, then it causes RPD crash when it is processed for a BGP UPDATE towards an EBGP peer. Repeated receipt and processing of the same specific BGP UPDATE can result in an extended Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS: 17.3R3-S6, 17.4R2-S7, and 18.1R3-S7. Juniper Networks Junos OS Evolved 19.2R2-EVO and later versions, prior to 19.3R1-EVO. Other Junos OS releases are not affected.

On Juniper Networks Junos OS devices configured with BGP origin validation using Resource Public Key Infrastructure (RPKI) receipt of a specific packet from the RPKI cache server may cause routing process daemon (RPD) to crash and restart, creating a Denial of Service (DoS) condition. Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS 17.3 versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S8, 18.4R3-S8; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R2-S4, 19.4R3-S3; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R2; 20.4 versions prior to 20.4R2. Juniper Networks Junos OS Evolved All versions prior to 20.4R2-S2-EVO.

On Juniper Networks Junos OS devices with Multipath or add-path feature enabled, processing a specific BGP UPDATE can lead to a routing process daemon (RPD) crash and restart, causing a Denial of Service (DoS). Continued receipt and processing of this UPDATE message will create a sustained Denial of Service (DoS) condition. This BGP UPDATE message can propagate to other BGP peers with vulnerable Junos versions on which Multipath or add-path feature is enabled, and cause RPD to crash and restart. This issue affects both IBGP and EBGP deployments in IPv4 or IPv6 network. Junos OS devices that do not have the BGP Multipath or add-path feature enabled are not affected by this issue. This issue affects: Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S18; 15.1 versions prior to 15.1R7-S9; 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S6, 18.4R3-S6; 19.1 versions prior to 19.1R3-S3;

A vulnerability in the handling of exceptional conditions in Juniper Networks Junos OS Evolved (EVO) allows an attacker to send specially crafted packets to the device, causing the Advanced Forwarding Toolkit manager (evo-aftmand-bt or evo-aftmand-zx) process to crash and restart, impacting all traffic going through the FPC, resulting in a Denial of Service (DoS). Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. Following messages will be logged prior to the crash: Feb 2 10:14:39 fpc0 evo-aftmand-bt[16263]: [Error] Nexthop: Failed to get fwd nexthop for nexthop:32710470974358 label:1089551617 for session:18 probe:35 Feb 2 10:14:39 fpc0 evo-aftmand-bt[16263]: [Error] Nexthop: Failed to get fwd nexthop for nexthop:19241453497049 label:1089551617 for session:18 probe:37 Feb 2 10:14:39 fpc0 evo-aftmand-bt[16263]: [Error] Nexthop: Failed to get fwd nexthop for nexthop:19241453497049 label:1089551617 for session:18 probe:44 Feb 2 10:14:39 fpc0 evo-aftmand-bt[16263]: [Error] Nexthop: Failed to get fwd nexthop for nexthop:32710470974358 label:1089551617 for session:18 probe:47 Feb 2 10:14:39 fpc0 audit[16263]: ANOM_ABEND auid=4294967295 uid=0 gid=0 ses=4294967295 pid=16263 comm="EvoAftManBt-mai" exe="/usr/sbin/evo-aftmand-bt" sig=11 Feb 2 10:14:39 fpc0 kernel: audit: type=1701 audit(1612260879.272:17): auid=4294967295 uid=0 gid=0 ses=4294967295 pid=16263 comm="EvoAftManBt-mai" exe="/usr/sbin/evo-aftmand-bt" sig=1 This issue affects Juniper Networks Junos OS Evolved: All versions prior to 20.4R2-EVO; 21.1 versions prior to 21.1R2-EVO.

An uncontrolled resource consumption vulnerability in Juniper Networks Junos OS on QFX5000 Series and EX4600 Series switches allows an attacker sending large amounts of legitimate traffic destined to the device to cause Interchassis Control Protocol (ICCP) interruptions, leading to an unstable control connection between the Multi-Chassis Link Aggregation Group (MC-LAG) nodes which can in turn lead to traffic loss. Continued receipt of this amount of traffic will create a sustained Denial of Service (DoS) condition. An indication that the system could be impacted by this issue is the following log message: "DDOS_PROTOCOL_VIOLATION_SET: Warning: Host-bound traffic for protocol/exception LOCALNH:aggregate exceeded its allowed bandwidth at fpc <fpc number> for <n> times, started at <timestamp>" This issue affects Juniper Networks Junos OS on QFX5000 Series and EX4600 Series: 15.1 versions prior to 15.1R7-S9; 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S5; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S8, 18.4R3-S7; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3-S2; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R2-S3, 20.2R3; 20.3 versions prior to 20.3R2; 20.4 versions prior to 20.4R1-S1, 20.4R2.

An Improper Handling of Exceptional Conditions vulnerability in the processing of a transit or directly received malformed IPv6 packet in Juniper Networks Junos OS results in a kernel crash, causing the device to restart, leading to a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue only affects systems with IPv6 configured. Devices with only IPv4 configured are not vulnerable to this issue. This issue affects Juniper Networks Junos OS: 19.4 versions prior to 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R1-S1, 20.2R2. This issue does not affect Juniper Networks Junos OS versions prior to 19.4R1.

Due to an Improper Initialization vulnerability in Juniper Networks Junos OS on PTX platforms and QFX10K Series with Paradise (PE) chipset-based line cards, ddos-protection configuration changes made from the CLI will not take effect as expected beyond the default DDoS (Distributed Denial of Service) settings in the Packet Forwarding Engine (PFE). This may cause BFD sessions to flap when a high rate of specific packets are received. Flapping of BFD sessions in turn may impact routing protocols and network stability, leading to a Denial of Service (DoS) condition. Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue affects only the following platforms with Paradise (PE) chipset-based line cards: PTX1000, PTX3000 (NextGen), PTX5000, PTX10008, PTX10016 Series and QFX10002 Series. This issue affects: Juniper Networks Junos OS 17.4 versions prior to 17.4R3-S5 on PTX Series, QFX10K Series; 18.2 versions prior to 18.2R3-S8 on PTX Series, QFX10K Series; 18.3 versions prior to 18.3R3-S5 on PTX Series, QFX10K Series; 18.4 versions prior to 18.4R2-S8 on PTX Series, QFX10K Series; 19.1 versions prior to 19.1R3-S5 on PTX Series, QFX10K Series; 19.2 versions prior to 19.2R3-S2 on PTX Series, QFX10K Series; 19.3 versions prior to 19.3R3-S2 on PTX Series, QFX10K Series; 19.4 versions prior to 19.4R3-S2 on PTX Series, QFX10K Series; 20.1 versions prior to 20.1R3 on PTX Series, QFX10K Series; 20.2 versions prior to 20.2R2-S3, 20.2R3 on PTX Series, QFX10K Series; 20.3 versions prior to 20.3R2 on PTX Series, QFX10K Series; 20.4 versions prior to 20.4R2 on PTX Series, QFX10K Series.

On Juniper Networks Junos OS Evolved devices, receipt of a specific IPv6 packet may cause an established IPv6 BGP session to terminate, creating a Denial of Service (DoS) condition. Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue does not affect IPv4 BGP sessions. This issue affects IBGP or EBGP peer sessions with IPv6. This issue affects: Juniper Networks Junos OS Evolved: 19.4 versions prior to 19.4R2-S3-EVO; 20.1 versions prior to 20.1R2-S3-EVO; 20.2 versions prior to 20.2R2-S1-EVO; 20.3 versions prior to 20.3R2-EVO. This issue does not affect Juniper Networks Junos OS releases.

An uncontrolled resource consumption vulnerability in Message Queue Telemetry Transport (MQTT) server of Juniper Networks Junos OS allows an attacker to cause MQTT server to crash and restart leading to a Denial of Service (DoS) by sending a stream of specific packets. A Juniper Extension Toolkit (JET) application designed with a listening port uses the Message Queue Telemetry Transport (MQTT) protocol to connect to a mosquitto broker that is running on Junos OS to subscribe for events. Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS: 16.1R1 and later versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R2-S4, 19.4R3-S2; 20.1 versions prior to 20.1R2-S1, 20.1R3; 20.2 versions prior to 20.2R2-S2, 20.2R3; 20.3 versions prior to 20.3R1-S1, 20.3R2. This issue does not affect Juniper Networks Junos OS versions prior to 16.1R1.

A vulnerability in Juniper Networks Junos OS ACX500 Series, ACX4000 Series, may allow an attacker to cause a Denial of Service (DoS) by sending a high rate of specific packets to the device, resulting in a Forwarding Engine Board (FFEB) crash. Continued receipt of these packets will sustain the Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on ACX500 Series, ACX4000 Series: 17.4 versions prior to 17.4R3-S2.

A NULL Pointer Dereference vulnerability in the Captive Portal Content Delivery (CPCD) services daemon (cpcd) of Juniper Networks Junos OS on MX Series with MS-PIC, MS-SPC3, MS-MIC or MS-MPC allows an attacker to send malformed HTTP packets to the device thereby causing a Denial of Service (DoS), crashing the Multiservices PIC Management Daemon (mspmand) process thereby denying users the ability to login, while concurrently impacting other mspmand services and traffic through the device. Continued receipt and processing of these malformed packets will create a sustained Denial of Service (DoS) condition. While the Services PIC is restarting, all PIC services will be bypassed until the Services PIC completes its boot process. An attacker sending these malformed HTTP packets to the device who is not part of the Captive Portal experience is not able to exploit this issue. This issue is not applicable to MX RE-based CPCD platforms. This issue affects: Juniper Networks Junos OS on MX Series 17.3 version 17.3R1 and later versions prior to 17.4 versions 17.4R2-S9, 17.4R3-S2; 18.1 versions prior to 18.1R3-S9; 18.2 versions prior to 18.2R3-S3; 18.3 versions prior to 18.3R3-S1; 18.4 versions prior to 18.4R3; 19.1 versions prior to 19.1R2-S2, 19.1R3; 19.2 versions prior to 19.2R2; 19.3 versions prior to 19.3R3. This issue does not affect: Juniper Networks Junos OS versions prior to 17.3R1.

On Juniper Networks SRX Series devices with link aggregation (lag) configured, executing any operation that fetches Aggregated Ethernet (AE) interface statistics, including but not limited to SNMP GET requests, causes a slow kernel memory leak. If all the available memory is consumed, the traffic will be impacted and a reboot might be required. The following log can be seen if this issue happens. /kernel: rt_pfe_veto: Memory over consumed. Op 1 err 12, rtsm_id 0:-1, msg type 72 /kernel: rt_pfe_veto: free kmem_map memory = (20770816) curproc = kmd An administrator can use the following CLI command to monitor the status of memory consumption (ifstat bucket): user@device > show system virtual-memory no-forwarding | match ifstat Type InUse MemUse HighUse Limit Requests Limit Limit Size(s) ifstat 2588977 162708K - 19633958 <<<< user@device > show system virtual-memory no-forwarding | match ifstat Type InUse MemUse HighUse Limit Requests Limit Limit Size(s) ifstat 3021629 189749K - 22914415 <<<< This issue affects Juniper Networks Junos OS on SRX Series: 17.1 versions 17.1R3 and above prior to 17.3R3-S11; 17.4 versions prior to 17.4R3-S5; 18.2 versions prior to 18.2R3-S7, 18.2R3-S8; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S7, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2-S2, 20.2R3; 20.3 versions prior to 20.3R1-S2, 20.3R2. This issue does not affect Juniper Networks Junos OS prior to 17.1R3.

An Improper Validation of Specified Type of Input vulnerability in Routing Protocol Daemon (RPD) of Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause Denial of Service (DoS). If a BGP update is received over an established BGP session which contains a tunnel encapsulation attribute with a specifically malformed TLV, rpd will crash and restart. This issue affects: Junos OS: * all versions before 21.2R3-S7,  * from 21.3 before 21.3R3-S5,  * from 21.4 before 21.4R3-S5,  * from 22.1 before 22.1R3-S5,  * from 22.2 before 22.2R3-S3,  * from 22.3 before 22.3R3-S2,  * from 22.4 before 22.4R3,  * from 23.2 before 23.2R1-S2, 23.2R2. Junos OS Evolved: * all versions before 21.2R3-S7-EVO,  * from 21.3-EVO before 21.3R3-S5-EVO,  * from 21.4-EVO before 21.4R3-S5-EVO,  * from 22.2-EVO before 22.2R3-S3-EVO,  * from 22.3-EVO before 22.3R3-S2-EVO,  * from 22.4-EVO before 22.4R3-EVO,  * from 23.2-EVO before 23.2R1-S2-EVO, 23.2R2-EVO. This is a related but separate issue than the one described in JSA75739

An Improper Handling of Exceptional Conditions vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a network-based, unauthenticated attacker to send a specific routing update, causing an rpd core due to memory corruption, leading to a Denial of Service (DoS). This issue can only be triggered when the system is configured for CoS-based forwarding (CBF) with a policy map containing a cos-next-hop-map action (see below). This issue affects: Junos OS: * all versions before 20.4R3-S10, * from 21.2 before 21.2R3-S8, * from 21.3 before 21.3R3, * from 21.4 before 21.4R3, * from 22.1 before 22.1R2; Junos OS Evolved: * all versions before 21.2R3-S8-EVO, * from 21.3 before 21.3R3-EVO, * from 21.4 before 21.4R3-EVO, * from 22.1 before 22.1R2-EVO.

A vulnerability in telnetd service on Junos OS allows a remote attacker to cause a limited memory and/or CPU consumption denial of service attack. This issue was found during internal product security testing. Affected releases are Juniper Networks Junos OS 12.1X46 prior to 12.1X46-D45; 12.3X48 prior to 12.3X48-D30; 14.1 prior to 14.1R4-S9, 14.1R8; 14.2 prior to 14.2R6; 15.1 prior to 15.1F5, 15.1R3; 15.1X49 prior to 15.1X49-D40; 15.1X53 prior to 15.1X53-D232, 15.1X53-D47.

Open redirect vulnerability in dana/home/homepage.cgi in Juniper Networks IVE 6.5R1 (Build 14599) and 6.5R2 (Build 14951) allows remote attackers to redirect users to arbitrary web sites and conduct phishing attacks via a URL in the Location parameter.

Pulse Connect Secure (aka PCS and formerly Juniper PCS) PSC6000, PCS6500, and MAG PSC360 8.1 before 8.1r5, 8.0 before 8.0r13, 7.4 before 7.4r13.5, and 7.1 before 7.1r22.2 and PPS 5.1 before 5.1R5 and 5.0 before 5.0R13, when Hardware Acceleration is enabled, does not properly validate the Finished TLS handshake message, which makes it easier for remote attackers to conduct man-in-the-middle attacks via a crafted Finished message.

Juniper Junos 11.4 before 11.4R12, 12.1 before 12.1R10, 12.1X44 before 12.1X44-D35, 12.1X45 before 12.1X45-D25, 12.1X46 before 12.1X46-D20, 12.1X47 before 12.1X47-D10, 12.2 before 12.2R8, 12.3 before 12.3R7, 13.1 before 13.1R4, 13.2 before 13.2R4, 13.3 before 13.3R2, and 14.1 before 14.1R1, when Auto-RP is enabled, allows remote attackers to cause a denial of service (RDP routing process crash and restart) via a malformed PIM packet.

Juniper Junos 11.4 before 11.4R12, 12.1X44 before 12.1X44-D32, 12.1X45 before 12.1X45-D25, 12.1X46 before 12.1X46-D20, and 12.1X47 before 12.1X47-D10 on SRX Series devices, when NAT protocol translation from IPv4 to IPv6 is enabled, allows remote attackers to cause a denial of service (flowd hang or crash) via a crafted packet.

The Juniper SRX Series devices with Junos 11.4 before 11.4R12-S4, 12.1X44 before 12.1X44-D40, 12.1X45 before 12.1X45-D30, 12.1X46 before 12.1X46-D25, and 12.1X47 before 12.1X47-D10, when an Application Layer Gateway (ALG) is enabled, allows remote attackers to cause a denial of service (flowd crash) via a crafted packet.

Juniper Junos 12.1X46 before 12.1X46-D20 and 12.1X47 before 12.1X47-D10 on SRX Series devices allows remote attackers to cause a denial of service (flowd crash) via a crafted SIP packet.

The Juniper Networks NetScreen Firewall devices with ScreenOS before 6.3r17, when configured to use the internal DNS lookup client, allows remote attackers to cause a denial of service (crash and reboot) via a sequence of malformed packets to the device IP.

An improper input validation vulnerability in the Routing Protocol Daemon (RPD) service of Juniper Networks Junos OS allows an attacker to send a malformed RSVP packet when bidirectional LSPs are in use, which when received by an egress router crashes the RPD causing a Denial of Service (DoS) condition. Continued receipt of the packet will sustain the Denial of Service. This issue affects: Juniper Networks Junos OS: All versions prior to 17.3R3-S10 except 15.1X49-D240 for SRX series; 17.4 versions prior to 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R2-S7, 18.2R3-S4; 18.3 versions prior to 18.3R3-S2; 18.4 versions prior to 18.4R1-S8, 18.4R2-S6, 18.4R3-S2; 19.1 versions prior to 19.1R1-S5, 19.1R3-S3; 19.2 versions prior to 19.2R3; 19.3 versions prior to 19.3R2-S5, 19.3R3; 19.4 versions prior to 19.4R2-S2, 19.4R3-S1; 20.1 versions prior to 20.1R1-S4, 20.1R2; 15.1X49 versions prior to 15.1X49-D240 on SRX Series. Juniper Networks Junos OS Evolved: 19.3 versions prior to 19.3R2-S5-EVO; 19.4 versions prior to 19.4R2-S2-EVO; 20.1 versions prior to 20.1R1-S4-EVO.

An Improper Input Validation vulnerability in the active-lease query portion in JDHCPD's DHCP Relay Agent of Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) by sending a crafted DHCP packet to the device thereby crashing the jdhcpd DHCP service. This is typically configured for Broadband Subscriber Sessions. Continued receipt and processing of this crafted packet will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS: 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R2-S1, 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R2. This issue does not affect Junos OS Evolved.

A vulnerability in the distributed or centralized periodic packet management daemon (PPMD) of Juniper Networks Junos OS may cause receipt of a malformed packet to crash and restart the PPMD process, leading to network destabilization, service interruption, and a Denial of Service (DoS) condition. Continued receipt and processing of these malformed packets will repeatedly crash the PPMD process and sustain the Denial of Service (DoS) condition. Due to the nature of the specifically crafted packet, exploitation of this issue requires direct, adjacent connectivity to the vulnerable component. This issue affects Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S12, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S6; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S4; 19.2 versions prior to 19.2R1-S5, 19.2R3-S1; 19.3 versions prior to 19.3R2-S5, 19.3R3-S1; 19.4 versions prior to 19.4R2-S2, 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R1-S2, 20.2R2.

Receipt of a specific Draft-Rosen MVPN control packet may cause the routing protocol daemon (RPD) process to crash and restart or may lead to remote code execution. By continuously sending the same specific Draft-Rosen MVPN control packet, an attacker can repeatedly crash the RPD process causing a prolonged denial of service. This issue may occur when the Junos OS device is configured for Draft-Rosen multicast virtual private network (MVPN). The VPN is multicast-enabled and configured to use Protocol Independent Multicast (PIM) protocol within the VPN. This issue can only be exploited from the PE device within the MPLS domain which is capable of forwarding IP multicast traffic in core. End-users connected to the CE device cannot cause this crash. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D77 on SRX Series; 12.3 versions prior to 12.3R12-S10; 12.3X48 versions prior to 12.3X48-D70 on SRX Series; 15.1 versions prior to 15.1R4-S9, 15.1R6-S6, 15.1R7; 15.1F6; 15.1X49 versions prior to 15.1X49-D140 on SRX Series; 15.1X53 versions prior to 15.1X53-D59 on EX2300/EX3400 Series; 15.1X53 versions prior to 15.1X53-D67 on QFX10K Series; 15.1X53 versions prior to 15.1X53-D233 on QFX5200/QFX5110 Series; 15.1X53 versions prior to 15.1X53-D471, 15.1X53-D490 on NFX Series; 16.1 versions prior to 16.1R4-S9, 16.1R5-S4, 16.1R6-S3, 16.1R7; 16.2 versions prior to 16.2R1-S6, 16.2R2-S6, 16.2R3; 17.1 versions prior to 17.1R1-S7, 17.1R2-S7, 17.1R3; 17.2 versions prior to 17.2R2-S4, 17.2R3; 17.3 versions prior to 17.3R2-S2, 17.3R3; 17.4 versions prior to 17.4R1-S3, 17.4R2; 18.1 versions prior to 18.1R2. No other Juniper Networks products or platforms are affected by this issue.

A Denial of Service vulnerability exists in the Juniper Networks Junos OS JDHCPD daemon which allows an attacker to core the JDHCPD daemon by sending a crafted IPv6 packet to the system. This issue is limited to systems which receives IPv6 DHCP packets on a system configured for DHCP processing using the JDHCPD daemon. This issue does not affect IPv4 DHCP packet processing. Affected releases are Juniper Networks Junos OS: 12.3 versions prior to 12.3R12-S10 on EX Series; 12.3X48 versions prior to 12.3X48-D70 on SRX Series; 14.1X53 versions prior to 14.1X53-D47 on EX2200/VC, EX3200, EX3300/VC, EX4200, EX4300, EX4550/VC, EX4600, EX6200, EX8200/VC (XRE), QFX3500, QFX3600, QFX5100; 14.1X53 versions prior to 14.1X53-D130 on QFabric; 15.1 versions prior to 15.1R4-S9, 15.1R6-S6, 15.1R7; 15.1X49 versions prior to 15.1X49-D140 on SRX Series; 15.1X53 versions prior to 15.1X53-D67 on QFX10000 Series; 15.1X53 versions prior to 15.1X53-D233 on QFX5110, QFX5200; 15.1X53 versions prior to 15.1X53-D471 on NFX 150, NFX 250; 16.1 versions prior to 16.1R3-S9, 16.1R4-S8, 16.1R5-S4, 16.1R6-S3, 16.1R7; 16.2 versions prior to 16.2R2-S5, 16.2R3; 17.1 versions prior to 17.1R1-S7, 17.1R2-S7, 17.1R3; 17.2 versions prior to 17.2R1-S6, 17.2R2-S4, 17.2R3; 17.3 versions prior to 17.3R1-S4, 17.3R2-S2, 17.3R3; 17.4 versions prior to 17.4R1-S3, 17.4R2.

Receipt of a specific MPLS packet may cause the routing protocol daemon (RPD) process to crash and restart or may lead to remote code execution. By continuously sending specific MPLS packets, an attacker can repeatedly crash the RPD process causing a sustained Denial of Service. This issue affects both IPv4 and IPv6. This issue can only be exploited from within the MPLS domain. End-users connected to the CE device cannot cause this crash. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D77 on SRX Series; 12.3 versions prior to 12.3R12-S10; 12.3X48 versions prior to 12.3X48-D75 on SRX Series; 14.1X53 versions prior to 14.1X53-D47 on QFX/EX Series; 14.1X53 versions prior to 14.1X53-D130 on QFabric Series; 15.1F6 versions prior to 15.1F6-S10; 15.1 versions prior to 15.1R4-S9 15.1R7; 15.1X49 versions prior to 15.1X49-D140 on SRX Series; 15.1X53 versions prior to 15.1X53-D59 on EX2300/EX3400 Series; 15.1X53 versions prior to 15.1X53-D67 on QFX10K Series; 15.1X53 versions prior to 15.1X53-D233 on QFX5200/QFX5110 Series; 15.1X53 versions prior to 15.1X53-D471 15.1X53-D490 on NFX Series; 16.1 versions prior to 16.1R3-S8 16.1R4-S8 16.1R5-S4 16.1R6-S4 16.1R7; 16.1X65 versions prior to 16.1X65-D48; 16.2 versions prior to 16.2R1-S6 16.2R3; 17.1 versions prior to 17.1R1-S7 17.1R2-S6 17.1R3; 17.2 versions prior to 17.2R1-S6 17.2R2-S3 17.2R3; 17.2X75 versions prior to 17.2X75-D100 17.2X75-D42 17.2X75-D91; 17.3 versions prior to 17.3R1-S4 17.3R2-S2 17.3R3; 17.4 versions prior to 17.4R1-S3 17.4R2 . No other Juniper Networks products or platforms are affected by this issue.

If a duplicate MAC address is learned by two different interfaces on an MX Series device, the MAC address learning function correctly flaps between the interfaces. However, the Layer 2 Address Learning Daemon (L2ALD) daemon might crash when attempting to delete the duplicate MAC address when the particular entry is not found in the internal MAC address table. This issue only occurs on MX Series devices with l2-backhaul VPN configured. No other products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS: 15.1 versions prior to 15.1R7-S1 on MX Series; 16.1 versions prior to 16.1R4-S12, 16.1R6-S6 on MX Series; 16.2 versions prior to 16.2R2-S7 on MX Series; 17.1 versions prior to 17.1R2-S9 on MX Series; 17.2 versions prior to 17.2R1-S7, 17.2R2-S6 on MX Series; 17.3 versions prior to 17.3R2-S4, 17.3R3-S1 on MX Series; 17.4 versions prior to 17.4R1-S5 on MX Series; 18.1 versions prior to 18.1R2 on MX Series.

Receipt of a specially crafted DHCPv6 message destined to a Junos OS device configured as a DHCP server in a Broadband Edge (BBE) environment may result in a jdhcpd daemon crash. The daemon automatically restarts without intervention, but a continuous receipt of crafted DHCPv6 packets could leaded to an extended denial of service condition. This issue only affects Junos OS 15.1 and later. Earlier releases are unaffected by this issue. Devices are only vulnerable to the specially crafted DHCPv6 message if DHCP services are configured. Devices not configured to act as a DHCP server are not vulnerable to this issue. Affected releases are Juniper Networks Junos OS: 15.1 versions prior to 15.1R7-S2; 15.1X49 versions prior to 15.1X49-D160; 15.1X53 versions prior to 15.1X53-D235, 15.1X53-D495; 16.1 versions prior to 16.1R4-S11, 16.1R6-S6, 16.1R7-S2; 16.2 versions prior to 16.2R2-S7; 17.1 versions prior to 17.1R2-S9; 17.2 versions prior to 17.2R2-S6; 17.3 versions prior to 17.3R3-S1; 17.4 versions prior to 17.4R1-S5; 18.1 versions prior to 18.1R2-S3; 18.2 versions prior to 18.2R1-S2; 18.2X75 versions prior to 18.2X75-D20.

Junos OS routing protocol daemon (RPD) process may crash and restart or may lead to remote code execution while processing specific BGP NOTIFICATION messages. By continuously sending crafted BGP NOTIFICATION messages, an attacker can repeatedly crash the RPD process causing a sustained Denial of Service. Due to design improvements, this issue does not affect Junos OS 16.1R1, and all subsequent releases. This issue only affects the receiving BGP device and is non-transitive in nature. Affected releases are Juniper Networks Junos OS: 15.1F5 versions starting from 15.1F5-S7 and all subsequent releases; 15.1F6 versions starting from 15.1F6-S3 and later releases prior to 15.1F6-S10; 15.1F7 versions 15.1 versions starting from 15.1R5 and later releases, including the Service Releases based on 15.1R5 and on 15.1R6 prior to 15.1R6-S6 and 15.1R7;

An improper input validation weakness in the device control daemon process (dcd) of Juniper Networks Junos OS allows an attacker to cause a Denial of Service to the dcd process and interfaces and connected clients when the Junos device is requesting an IP address for itself. Junos devices are not vulnerable to this issue when not configured to use DHCP. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D40 on SRX Series; 12.3X48 versions prior to 12.3X48-D20 on SRX Series; 14.1X53 versions prior to 14.1X53-D40 on EX2200/VC, EX3200, EX3300/VC, EX4200, EX4300, EX4550/VC, EX4600, EX6200, EX8200/VC (XRE), QFX3500, QFX3600, QFX5100; 15.1X49 versions prior to 15.1X49-D20 on SRX Series; 15.1X53 versions prior to 15.1X53-D68 on QFX10000 Series; 15.1X53 versions prior to 15.1X53-D235 on QFX5200/QFX5110; 15.1X53 versions prior to 15.1X53-D495 on NFX150, NFX250; 15.1X53 versions prior to 15.1X53-D590 on EX2300/EX3400; 15.1 versions prior to 15.1R7-S2.

An XPath Injection vulnerability due to Improper Input Validation in the J-Web component of Juniper Networks Junos OS allows an authenticated attacker to add an XPath command to the XPath stream, which may allow chaining to other unspecified vulnerabilities, leading to a partial loss of confidentiality. This issue affects Juniper Networks Junos OS: all versions prior to 19.1R3-S9; 19.2 versions prior to 19.2R3-S6; 19.3 versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R2-S7, 19.4R3-S8; 20.1 versions prior to 20.1R3-S5; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S2; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R2-S2, 21.3R3; 21.4 versions prior to 21.4R1-S2, 21.4R2-S1, 21.4R3; 22.1 versions prior to 22.1R1-S1, 22.1R2.