The Routing Engine in Juniper Junos OS 13.2R5 through 13.2R8, 13.3R1 before 13.3R8, 13.3R7 before 13.3R7-S3, 14.1R1 before 14.1R6, 14.1R3 before 14.1R3-S9, 14.1R4 before 14.1R4-S7, 14.1X51 before 14.1X51-D65, 14.1X53 before 14.1X53-D12, 14.1X53 before 14.1X53-D28, 14.1X53 before 4.1X53-D35, 14.2R1 before 14.2R5, 14.2R3 before 14.2R3-S4, 14.2R4 before 14.2R4-S1, 15.1 before 15.1R3, 15.1F2 before 15.1F2-S2, and 15.1X49 before 15.1X49-D40, when LDP is enabled, allows remote attackers to cause a denial of service (RPD routing process crash) via a crafted LDP packet.

Juniper Junos OS before 12.1X46-D45, 12.1X46-D50, 12.1X47 before 12.1X47-D35, 12.3X48 before 12.3X48-D30, 13.3 before 13.3R9-S1, 14.1 before 14.1R7, 14.2 before 14.2R6, 15.1 before 15.1F2-S5, 15.1F4 before 15.1F4-S2, 15.1R before 15.1R2-S3, 15.1 before 15.1R3, and 15.1X49 before 15.1X49-D40 allow remote attackers to cause a denial of service (kernel crash) via a crafted UDP packet destined to the interface IP address of a 64-bit OS device.

On SRX Series devices, a crafted ICMP packet embedded within a NAT64 IPv6 to IPv4 tunnel may cause the flowd process to crash. Repeated crashes of the flowd process constitutes an extended denial of service condition for the SRX Series device. This issue only occurs if NAT64 is configured. Affected releases are Juniper Networks Junos OS 12.1X46 prior to 12.1X46-D71, 12.3X48 prior to 12.3X48-D55, 15.1X49 prior to 15.1X49-D100 on SRX Series. No other Juniper Networks products or platforms are affected by this issue.

A vulnerability in the Network Address Translation - Protocol Translation (NAT-PT) feature of Junos OS on SRX series devices may allow a certain valid IPv6 packet to crash the flowd daemon. Repeated crashes of the flowd daemon can result in an extended denial of service condition for the SRX device. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D72; 12.3X48 versions prior to 12.3X48-D55; 15.1X49 versions prior to 15.1X49-D90.

The administrative web services interface in Juniper ScreenOS before 6.3.0r21 allows remote attackers to cause a denial of service (reboot) via a crafted SSL packet.

Juniper Junos OS before 12.1X46-D50, 12.1X47 before 12.1X47-D40, 12.3X48 before 12.3X48-D30, 13.3 before 13.3R9, 14.1 before 14.1R8, 14.1X53 before 14.1X53-D40, 14.2 before 14.2R6, 15.1 before 15.1F6 or 15.1R3, and 15.1X49 before 15.1X49-D40, when configured with a GRE or IPIP tunnel, allow remote attackers to cause a denial of service (kernel panic) via a crafted ICMP packet.

Juniper Junos OS before 12.1X46-D45, 12.1X47 before 12.1X47-D30, 12.1X48 before 12.3X48-D20, and 15.1X49 before 15.1X49-D30 on SRX series devices, when the Real Time Streaming Protocol Application Layer Gateway (RTSP ALG) is enabled, allow remote attackers to cause a denial of service (flowd crash) via a crafted RTSP packet.

Juniper Junos 10.0 before 10.0S28, 10.4 before 10.4R7, 11.1 before 11.1R5, 11.2 before 11.2R2, and 11.4 before 11.4R1, when in a Next-Generation Multicast VPN (NGEN MVPN) environment, allows remote attackers to cause a denial of service (RPD routing daemon crash) via a large number of crafted PIM (S,G) join requests.

Juniper Junos before 10.4S14, 11.4 before 11.4R5-S2, 12.1R before 12.1R3, 12.1X44 before 12.1X44-D20, and 12.1X45 before 12.1X45-D15 on SRX Series services gateways, when a plugin using TCP proxy is configured, allows remote attackers to cause a denial of service (flow daemon crash) via an unspecified sequence of TCP packets.

Receipt of a specially crafted IPv6 exception packet may be able to trigger a kernel crash (vmcore), causing the device to reboot. The issue is specific to the processing of Broadband Edge (BBE) client route processing on MX Series subscriber management platforms, introduced by the Tomcat (Next Generation Subscriber Management) functionality in Junos OS 15.1. This issue affects no other platforms or configurations. Affected releases are Juniper Networks Junos OS: 15.1 versions prior to 15.1R7-S2, 15.1R8 on MX Series; 16.1 versions prior to 16.1R4-S11, 16.1R7-S2, 16.1R8 on MX Series; 16.2 versions prior to 16.2R3 on MX Series; 17.1 versions prior to 17.1R2-S9, 17.1R3 on MX Series; 17.2 versions prior to 17.2R2-S6, 17.2R3 on MX Series; 17.3 versions prior to 17.3R2-S4, 17.3R3-S2, 17.3R4 on MX Series; 17.4 versions prior to 17.4R2 on MX Series; 18.1 versions prior to 18.1R2-S3, 18.1R3 on MX Series; 18.2 versions prior to 18.2R1-S1, 18.2R2 on MX Series.

A Denial of Service vulnerability in J-Web service may allow a remote unauthenticated user to cause Denial of Service which may prevent other users to authenticate or to perform J-Web operations. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D77 on SRX Series; 12.3 versions prior to 12.3R12-S10; 12.3X48 versions prior to 12.3X48-D60 on SRX Series; 15.1 versions prior to 15.1R7; 15.1F6; 15.1X49 versions prior to 15.1X49-D120 on SRX Series; 15.1X53 versions prior to 15.1X53-D59 on EX2300/EX3400 Series; 15.1X53 versions prior to 15.1X53-D67 on QFX10K Series; 15.1X53 versions prior to 15.1X53-D234 on QFX5200/QFX5110 Series; 15.1X53 versions prior to 15.1X53-D470, 15.1X53-D495 on NFX Series; 16.1 versions prior to 16.1R6; 16.2 versions prior to 16.2R2-S6, 16.2R3; 17.1 versions prior to 17.1R2-S6, 17.1R3; 17.2 versions prior to 17.2R3; 17.3 versions prior to 17.3R2. No other Juniper Networks products or platforms are affected by this issue.

The receipt of a crafted BGP UPDATE can lead to a routing process daemon (RPD) crash and restart. Repeated receipt of the same crafted BGP UPDATE can result in an extended denial of service condition for the device. This issue only affects the specific versions of Junos OS listed within this advisory. Earlier releases are unaffected by this vulnerability. This crafted BGP UPDATE does not propagate to other BGP peers. Affected releases are Juniper Networks Junos OS: 16.1X65 versions prior to 16.1X65-D47; 17.2X75 versions prior to 17.2X75-D91, 17.2X75-D110; 17.3 versions prior to 17.3R1-S4, 17.3R2; 17.4 versions prior to 17.4R1-S3, 17.4R2.

On Juniper Networks Junos OS and Junos OS Evolved devices, BGP session flapping can lead to a routing process daemon (RPD) crash and restart, limiting the attack surface to configured BGP peers. This issue only affects devices with BGP damping in combination with accepted-prefix-limit configuration. When the issue occurs the following messages will appear in the /var/log/messages: rpd[6046]: %DAEMON-4-BGP_PREFIX_THRESH_EXCEEDED: XXXX (External AS x): Configured maximum accepted prefix-limit threshold(1800) exceeded for inet6-unicast nlri: 1984 (instance master) rpd[6046]: %DAEMON-3-BGP_CEASE_PREFIX_LIMIT_EXCEEDED: 2001:x:x:x::2 (External AS x): Shutting down peer due to exceeding configured maximum accepted prefix-limit(2000) for inet6-unicast nlri: 2001 (instance master) rpd[6046]: %DAEMON-4: bgp_rt_maxprefixes_check_common:9284: NOTIFICATION sent to 2001:x:x:x::2 (External AS x): code 6 (Cease) subcode 1 (Maximum Number of Prefixes Reached) AFI: 2 SAFI: 1 prefix limit 2000 kernel: %KERN-5: mastership_relinquish_on_process_exit: RPD crashed on master RE. Sending SIGUSR2 to chassisd (5612:chassisd) to trigger RE switchover This issue affects: Juniper Networks Junos OS: 17.2R3-S3; 17.3 version 17.3R3-S3 and later versions, prior to 17.3R3-S8; 17.4 version 17.4R2-S4, 17.4R3 and later versions, prior to 17.4R2-S10, 17.4R3-S2; 18.1 version 18.1R3-S6 and later versions, prior to 18.1R3-S10; 18.2 version 18.2R3 and later versions, prior to 18.2R3-S4; 18.2X75 version 18.2X75-D50, 18.2X75-D60 and later versions, prior to 18.2X75-D53, 18.2X75-D65; 18.3 version 18.3R2 and later versions, prior to 18.3R2-S4, 18.3R3-S2; 18.4 version 18.4R2 and later versions, prior to 18.4R2-S5, 18.4R3-S2; 19.1 version 19.1R1 and later versions, prior to 19.1R2-S2, 19.1R3-S1; 19.2 version 19.2R1 and later versions, prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2; 20.1 versions prior to 20.1R1-S2, 20.1R2. Juniper Networks Junos OS Evolved prior to 20.1R2-EVO. This issue does not affect Juniper Networks Junos OS versions prior to 17.2R3-S3.

A vulnerability in Junos OS SNMP MIB-II subagent daemon (mib2d) may allow a remote network based attacker to cause the mib2d process to crash resulting in a denial of service condition (DoS) for the SNMP subsystem. While a mib2d process crash can disrupt the network monitoring via SNMP, it does not impact routing, switching or firewall functionalities. SNMP is disabled by default on devices running Junos OS. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D76; 12.3 versions prior to 12.3R12-S7, 12.3R13; 12.3X48 versions prior to 12.3X48-D65; 14.1 versions prior to 14.1R9; 14.1X53 versions prior to 14.1X53-D130; 15.1 versions prior to 15.1F2-S20, 15.1F6-S10, 15.1R7; 15.1X49 versions prior to 15.1X49-D130; 15.1X53 versions prior to 15.1X53-D233, 15.1X53-D471, 15.1X53-D472, 15.1X53-D58, 15.1X53-D66; 16.1 versions prior to 16.1R5-S3, 16.1R7; 16.1X65 versions prior to 16.1X65-D47; 16.1X70 versions prior to 16.1X70-D10; 16.2 versions prior to 16.2R1-S6, 16.2R2-S5, 16.2R3; 17.1 versions prior to 17.1R2-S6, 17.1R3;

A Denial of Service vulnerability in the SIP application layer gateway (ALG) component of Junos OS based platforms allows an attacker to crash MS-PIC, MS-MIC, MS-MPC, MS-DPC or SRX flow daemon (flowd) process. This issue affects Junos OS devices with NAT or stateful firewall configuration in combination with the SIP ALG enabled. SIP ALG is enabled by default on SRX Series devices except for SRX-HE devices. SRX-HE devices have SIP ALG disabled by default. The status of ALGs in SRX device can be obtained by executing the command: show security alg status Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D77; 12.3X48 versions prior to 12.3X48-D70; 15.1X49 versions prior to 15.1X49-D140; 15.1 versions prior to 15.1R4-S9, 15.1R7-S1; 15.1F6; 16.1 versions prior to 16.1R4-S9, 16.1R6-S1, 16.1R7; 16.2 versions prior to 16.2R2-S7, 16.2R3; 17.1 versions prior to 17.1R2-S7, 17.1R3; 17.2 versions prior to 17.2R1-S6, 17.2R2-S4, 17.2R3; 17.3 versions prior to 17.3R1-S5, 17.3R2-S2, 17.3R3; 17.4 versions prior to 17.4R2. No other Juniper Networks products or platforms are affected by this issue.

An improper input validation weakness in the device control daemon process (dcd) of Juniper Networks Junos OS allows an attacker to cause a Denial of Service to the dcd process and interfaces and connected clients when the Junos device is requesting an IP address for itself. Junos devices are not vulnerable to this issue when not configured to use DHCP. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D40 on SRX Series; 12.3X48 versions prior to 12.3X48-D20 on SRX Series; 14.1X53 versions prior to 14.1X53-D40 on EX2200/VC, EX3200, EX3300/VC, EX4200, EX4300, EX4550/VC, EX4600, EX6200, EX8200/VC (XRE), QFX3500, QFX3600, QFX5100; 15.1X49 versions prior to 15.1X49-D20 on SRX Series; 15.1X53 versions prior to 15.1X53-D68 on QFX10000 Series; 15.1X53 versions prior to 15.1X53-D235 on QFX5200/QFX5110; 15.1X53 versions prior to 15.1X53-D495 on NFX150, NFX250; 15.1X53 versions prior to 15.1X53-D590 on EX2300/EX3400; 15.1 versions prior to 15.1R7-S2.

A Denial of Service vulnerability exists in the Juniper Networks Junos OS JDHCPD daemon which allows an attacker to core the JDHCPD daemon by sending a crafted IPv6 packet to the system. This issue is limited to systems which receives IPv6 DHCP packets on a system configured for DHCP processing using the JDHCPD daemon. This issue does not affect IPv4 DHCP packet processing. Affected releases are Juniper Networks Junos OS: 12.3 versions prior to 12.3R12-S10 on EX Series; 12.3X48 versions prior to 12.3X48-D70 on SRX Series; 14.1X53 versions prior to 14.1X53-D47 on EX2200/VC, EX3200, EX3300/VC, EX4200, EX4300, EX4550/VC, EX4600, EX6200, EX8200/VC (XRE), QFX3500, QFX3600, QFX5100; 14.1X53 versions prior to 14.1X53-D130 on QFabric; 15.1 versions prior to 15.1R4-S9, 15.1R6-S6, 15.1R7; 15.1X49 versions prior to 15.1X49-D140 on SRX Series; 15.1X53 versions prior to 15.1X53-D67 on QFX10000 Series; 15.1X53 versions prior to 15.1X53-D233 on QFX5110, QFX5200; 15.1X53 versions prior to 15.1X53-D471 on NFX 150, NFX 250; 16.1 versions prior to 16.1R3-S9, 16.1R4-S8, 16.1R5-S4, 16.1R6-S3, 16.1R7; 16.2 versions prior to 16.2R2-S5, 16.2R3; 17.1 versions prior to 17.1R1-S7, 17.1R2-S7, 17.1R3; 17.2 versions prior to 17.2R1-S6, 17.2R2-S4, 17.2R3; 17.3 versions prior to 17.3R1-S4, 17.3R2-S2, 17.3R3; 17.4 versions prior to 17.4R1-S3, 17.4R2.

Junos OS may be impacted by the receipt of a malformed BGP UPDATE which can lead to a routing process daemon (rpd) crash and restart. Receipt of a repeated malformed BGP UPDATEs can result in an extended denial of service condition for the device. This malformed BGP UPDATE does not propagate to other BGP peers. Affected releases are Juniper Networks Junos OS: 14.1X53 versions prior to 14.1X53-D47; 15.1 versions prior to 15.1F6-S10, 15.1R4-S9, 15.1R6-S6, 15.1R7; 15.1X49 versions prior to 15.1X49-D130 on SRX; 15.1X53 versions prior to 15.1X53-D66 on QFX10K; 15.1X53 versions prior to 15.1X53-D58 on EX2300/EX3400; 15.1X53 versions prior to 15.1X53-D233 on QFX5200/QFX5110; 15.1X53 versions prior to 15.1X53-D471 on NFX; 16.1 versions prior to 16.1R3-S8, 16.1R4-S9, 16.1R5-S3, 16.1R6-S3, 16.1R7; 16.1X65 versions prior to 16.1X65-D47; 16.2 versions prior to 16.2R1-S6, 16.2R2-S5, 16.2R3; 17.1 versions prior to 17.1R2-S3, 17.1R3; 17.2 versions prior to 17.2R1-S3, 17.2R2-S1, 17.2R3; 17.2X75 versions prior to 17.2X75-D70; 13.2 versions above and including 13.2R1. Versions prior to 13.2R1 are not affected. Juniper SIRT is not aware of any malicious exploitation of this vulnerability. No other Juniper Networks products or platforms are affected by this issue.

Receipt of a crafted or malformed RSVP PATH message may cause the routing protocol daemon (RPD) to hang or crash. When RPD is unavailable, routing updates cannot be processed which can lead to an extended network outage. If RSVP is not enabled on an interface, then the issue cannot be triggered via that interface. This issue only affects Juniper Networks Junos OS 16.1 versions prior to 16.1R3. This issue does not affect Junos releases prior to 16.1R1.

Juniper Networks devices running affected Junos OS versions may be impacted by the receipt of a crafted BGP UPDATE which can lead to an rpd (routing process daemon) crash and restart. Repeated crashes of the rpd daemon can result in an extended denial of service condition. The affected Junos OS versions are: 15.1 prior to 15.1F2-S15, 15.1F5-S7, 15.1F6-S5, 15.1F7, 15.1R4-S7, 15.1R5-S2, 15.1R6; 15.1X49 prior to 15.1X49-D78, 15.1X49-D80; 15.1X53 prior to 15.1X53-D230, 15.1X53-D63, 15.1X53-D70; 16.1 prior to 16.1R3-S3, 16.1R4; 16.2 prior to 16.2R1-S3, 16.2R2; Releases prior to Junos OS 15.1 are unaffected by this vulnerability. 17.1R1, 17.2R1, and all subsequent releases have a resolution for this vulnerability.

Receipt of a malformed BGP OPEN message may cause the routing protocol daemon (rpd) process to crash and restart. By continuously sending specially crafted BGP OPEN messages, an attacker can repeatedly crash the rpd process causing prolonged denial of service. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS 12.3 prior to 12.3R12-S4, 12.3R13, 12.3R3-S4; 12.3X48 prior to 12.3X48-D50; 13.3 prior to 13.3R4-S11, 13.3R10; 14.1 prior to 14.1R8-S3, 14.1R9; 14.1X53 prior to 14.1X53-D40; 14.1X55 prior to 14.1X55-D35; 14.2 prior to 14.2R4-S7, 14.2R6-S4, 14.2R7; 15.1 prior to 15.1F2-S11, 15.1F4-S1-J1, 15.1F5-S3, 15.1F6, 15.1R4; 15.1X49 prior to 15.1X49-D100; 15.1X53 prior to 15.1X53-D33, 15.1X53-D50.

A denial of service vulnerability in rpd daemon of Juniper Networks Junos OS allows a malformed MPLS ping packet to crash the rpd daemon if MPLS OAM is configured. Repeated crashes of the rpd daemon can result in an extended denial of service condition for the device. The affected releases are Junos OS 12.3X48 prior to 12.3X48-D50, 12.3X48-D55; 13.3 prior to 13.3R10; 14.1 prior to 14.1R4-S13, 14.1R8-S3, 14.1R9; 14.1X53 prior to 14.1X53-D42, 14.1X53-D50; 14.2 prior to 14.2R4-S8, 14.2R7-S6, 14.2R8; 15.1 prior to 15.1F2-S14, 15.1F5-S7, 15.1F6-S4, 15.1F7, 15.1R4-S7, 15.1R5-S1, 15.1R6; 15.1X49 prior to 15.1X49-D100; 15.1X53 prior to 15.1X53-D105, 15.1X53-D47, 15.1X53-D62, 15.1X53-D70; 16.1 prior to 16.1R3-S3, 16.1R4. No other Juniper Networks products or platforms are affected by this issue.

On all vSRX and SRX Series devices, when the DHCP or DHCP relay is configured, specially crafted packet might cause the flowd process to crash, halting or interrupting traffic from flowing through the device(s). Repeated crashes of the flowd process may constitute an extended denial of service condition for the device(s). If the device is configured in high-availability, the RG1+ (data-plane) will fail-over to the secondary node. If the device is configured in stand-alone, there will be temporary traffic interruption until the flowd process is restored automatically. Sustained crafted packets may cause the secondary failover node to fail back, or fail completely, potentially halting flowd on both nodes of the cluster or causing flip-flop failovers to occur. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS 12.1X46 prior to 12.1X46-D67 on vSRX or SRX Series; 12.3X48 prior to 12.3X48-D50 on vSRX or SRX Series; 15.1X49 prior to 15.1X49-D91, 15.1X49-D100 on vSRX or SRX Series.

On Juniper Networks PTX and QFX Series devices with packet sampling configured using tunnel-observation mpls-over-udp, sampling of a malformed packet can cause the Kernel Routing Table (KRT) queue to become stuck. KRT is the module within the Routing Process Daemon (RPD) that synchronized the routing tables with the forwarding tables in the kernel. This table is then synchronized to the Packet Forwarding Engine (PFE) via the KRT queue. Thus, when KRT queue become stuck, it can lead to unexpected packet forwarding issues. An administrator can monitor the following command to check if there is the KRT queue is stuck: user@device > show krt state ... Number of async queue entries: 65007 <--- this value keep on increasing. When this issue occurs, the following message might appear in the /var/log/messages: DATE DEVICE kernel: %KERN-3: rt_pfe_veto: Too many delayed route/nexthop unrefs. Op 2 err 55, rtsm_id 5:-1, msg type 2 DATE DEVICE kernel: %KERN-3: rt_pfe_veto: Memory usage of M_RTNEXTHOP type = (0) Max size possible for M_RTNEXTHOP type = (7297134592) Current delayed unref = (60000), Current unique delayed unref = (18420), Max delayed unref on this platform = (40000) Current delayed weight unref = (60000) Max delayed weight unref on this platform= (400000) curproc = rpd This issue affects Juniper Networks Junos OS on PTX/QFX Series: 17.2X75 versions prior to 17.2X75-D105; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S5; 18.2X75 versions prior to 18.2X75-D420, 18.2X75-D53, 18.2X75-D65; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R1-S7, 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R2-S2, 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S2, 20.1R2. This issue does not affect Juniper Networks Junos OS prior to 18.1R1.

Receipt of a specifically malformed IPv6 packet processed by the router may trigger a line card reset: processor exception 0x68616c74 (halt) in task: scheduler. The line card will reboot and recover without user interaction. However, additional specifically malformed packets may cause follow-on line card resets and lead to an extended service outage. This issue only affects E Series routers with IPv6 licensed and enabled. Routers not configured to process IPv6 traffic are unaffected by this vulnerability. Juniper SIRT is not aware of any malicious exploitation of this vulnerability. No other Juniper Networks products or platforms are affected by this issue.

An Improper Check for Unusual or Exceptional Conditions vulnerability combined with a Race Condition in the flow daemon (flowd) of Juniper Networks Junos OS on SRX300 Series, SRX500 Series, SRX1500, and SRX5000 Series with SPC2 allows an unauthenticated network based attacker sending specific traffic to cause a crash of the flowd/srxpfe process, responsible for traffic forwarding in SRX, which will cause a Denial of Service (DoS). Continued receipt and processing of this specific traffic will create a sustained Denial of Service (DoS) condition. This issue can only occur when specific packets are trying to create the same session and logging for session-close is configured as a policy action. Affected platforms are: SRX300 Series, SRX500 Series, SRX1500, and SRX5000 Series with SPC2. Not affected platforms are: SRX4000 Series, SRX5000 Series with SPC3, and vSRX Series. This issue affects Juniper Networks Junos OS SRX300 Series, SRX500 Series, SRX1500, and SRX5000 Series with SPC2: All versions prior to 17.4R3-S5; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S4, 19.4R3-S3; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R2-S1, 20.3R3; 20.4 versions prior to 20.4R2.

On MX Series platforms with MS-MPC/MS-MIC, an Allocation of Resources Without Limits or Throttling vulnerability in Juniper Networks Junos OS allows an unauthenticated network attacker to cause a partial Denial of Service (DoS) with a high rate of specific traffic. If a Class of Service (CoS) rule is attached to the service-set and a high rate of specific traffic is processed by this service-set, for some of the other traffic which has services applied and is being processed by this MS-MPC/MS-MIC drops will be observed. Continued receipted of this high rate of specific traffic will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on MX Series with MS-MPC/MS-MIC: All versions prior to 17.4R3-S5; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S7, 19.3R3-S3; 19.4 versions prior to 19.4R3-S5; 20.1 versions prior to 20.1R2-S2, 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R2-S1, 20.4R3; 21.1 versions prior to 21.1R1-S1, 21.1R2.

Juniper Junos OS before 12.1X44-D60, 12.1X46 before 12.1X46-D40, 12.1X47 before 12.1X47-D30, 12.3 before 12.3R11, 12.3X48 before 12.3X48-D20, 13.2 before 13.2R9, 13.2X51 before 13.2X51-D39, 13.3 before 13.3R8, 14.1 before 14.1R6, 14.1X53 before 14.1X53-D30, 14.2 before 14.2R4-S1, 15.1 before 15.1R2, 15.1X49 before 15.1X49-D30, and 16.1 before 16.1R1 allow remote attackers to cause a denial of service (socket consumption) via crafted TCP timestamps.

In broadband environments, including but not limited to Enhanced Subscriber Management, (CHAP, PPP, DHCP, etc.), on Juniper Networks Junos OS devices where RADIUS servers are configured for managing subscriber access and a subscriber is logged in and then requests to logout, the subscriber may be forced into a "Terminating" state by an attacker who is able to send spoofed messages appearing to originate from trusted RADIUS server(s) destined to the device in response to the subscriber's request. These spoofed messages cause the Junos OS General Authentication Service (authd) daemon to force the broadband subscriber into this "Terminating" state which the subscriber will not recover from thereby causing a Denial of Service (DoS) to the endpoint device. Once in the "Terminating" state, the endpoint subscriber will no longer be able to access the network. Restarting the authd daemon on the Junos OS device will temporarily clear the subscribers out of the "Terminating" state. As long as the attacker continues to send these spoofed packets and subscribers request to be logged out, the subscribers will be returned to the "Terminating" state thereby creating a persistent Denial of Service to the subscriber. An indicator of compromise may be seen by displaying the output of "show subscribers summary". The presence of subscribers in the "Terminating" state may indicate the issue is occurring. This issue affects: Juniper Networks Junos OS 17.3 versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S8, 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R1-S4, 19.4R3-S3; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S1; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2. This issue does not affect: Juniper Networks Junos OS 12.3 version 12.3R1 and later versions; 15.1 version 15.1R1 and later versions.

In Point to MultiPoint (P2MP) scenarios within established sessions between network or adjacent neighbors the improper use of a source to destination copy write operation combined with a Stack-based Buffer Overflow on certain specific packets processed by the routing protocol daemon (RPD) of Juniper Networks Junos OS and Junos OS Evolved sent by a remote unauthenticated network attacker causes the RPD to crash causing a Denial of Service (DoS). Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3-S3; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R2-S3, 20.2R3; 20.3 versions prior to 20.3R2. This issue does not affect Juniper Networks Junos OS versions prior to 19.2R1. Juniper Networks Junos OS Evolved 20.1 versions prior to 20.1R3-EVO; 20.2 versions prior to 20.2R3-EVO; 20.3 versions prior to 20.3R2-EVO.

A vulnerability in telnetd service on Junos OS allows a remote attacker to cause a limited memory and/or CPU consumption denial of service attack. This issue was found during internal product security testing. Affected releases are Juniper Networks Junos OS 12.1X46 prior to 12.1X46-D45; 12.3X48 prior to 12.3X48-D30; 14.1 prior to 14.1R4-S9, 14.1R8; 14.2 prior to 14.2R6; 15.1 prior to 15.1F5, 15.1R3; 15.1X49 prior to 15.1X49-D40; 15.1X53 prior to 15.1X53-D232, 15.1X53-D47.

Juniper Networks Junos OS 16.1R1, and services releases based off of 16.1R1, are vulnerable to the receipt of a crafted BGP Protocol Data Unit (PDU) sent directly to the router, which can cause the RPD routing process to crash and restart. Unlike BGP UPDATEs, which are transitive in nature, this issue can only be triggered by a packet sent directly to the IP address of the router. Repeated crashes of the rpd daemon can result in an extended denial of service condition. This issue only affects devices running Junos OS 16.1R1 and services releases based off of 16.1R1 (e.g. 16.1R1-S1, 16.1R1-S2, 16.1R1-S3). No prior versions of Junos OS are affected by this vulnerability, and this issue was resolved in Junos OS 16.2 prior to 16.2R1. No other Juniper Networks products or platforms are affected by this issue. This issue was found during internal product security testing.

Any Juniper Networks SRX series device with one or more ALGs enabled may experience a flowd crash when traffic is processed by the Sun/MS-RPC ALGs. This vulnerability in the Sun/MS-RPC ALG services component of Junos OS allows an attacker to cause a repeated denial of service against the target. Repeated traffic in a cluster may cause repeated flip-flop failure operations or full failure to the flowd daemon halting traffic on all nodes. Only IPv6 traffic is affected by this issue. IPv4 traffic is unaffected. This issues is not seen with to-host traffic. This issue has no relation with HA services themselves, only the ALG service. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS 12.1X46 prior to 12.1X46-D55 on SRX; 12.1X47 prior to 12.1X47-D45 on SRX; 12.3X48 prior to 12.3X48-D32, 12.3X48-D35 on SRX; 15.1X49 prior to 15.1X49-D60 on SRX.

Receipt of specially crafted UDP/IP packets over MPLS may be able to bypass a stateless firewall filter. The crafted UDP packets must be encapsulated and meet a very specific packet format to be classified in a way that bypasses IP firewall filter rules. The packets themselves do not cause a service interruption (e.g. RPD crash), but receipt of a high rate of UDP packets may be able to contribute to a denial of service attack. This issue only affects processing of transit UDP/IP packets over MPLS, received on an interface with MPLS enabled. TCP packet processing and non-MPLS encapsulated UDP packet processing are unaffected by this issue. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D76; 12.3 versions prior to 12.3R12-S10; 12.3X48 versions prior to 12.3X48-D66, 12.3X48-D70; 14.1X53 versions prior to 14.1X53-D47; 15.1 versions prior to 15.1F6-S10, 15.1R4-S9, 15.1R6-S6, 15.1R7; 15.1X49 versions prior to 15.1X49-D131, 15.1X49-D140; 15.1X53 versions prior to 15.1X53-D59 on EX2300/EX3400; 15.1X53 versions prior to 15.1X53-D67 on QFX10K; 15.1X53 versions prior to 15.1X53-D233 on QFX5200/QFX5110; 15.1X53 versions prior to 15.1X53-D471, 15.1X53-D490 on NFX; 16.1 versions prior to 16.1R3-S8, 16.1R4-S9, 16.1R5-S4, 16.1R6-S3, 16.1R7; 16.2 versions prior to 16.2R1-S6, 16.2R2-S5, 16.2R3; 17.1 versions prior to 17.1R1-S7, 17.1R2-S7, 17.1R3; 17.2 versions prior to 17.2R1-S6, 17.2R2-S4, 17.2R3; 17.2X75 versions prior to 17.2X75-D100; 17.3 versions prior to 17.3R1-S4, 17.3R2-S2, 17.3R3; 17.4 versions prior to 17.4R1-S3, 17.4R2; 18.1 versions prior to 18.1R2; 18.2X75 versions prior to 18.2X75-D5.

If extended statistics are enabled via 'set chassis extended-statistics', when executing any operation that fetches interface statistics, including but not limited to SNMP GET requests, the pfem process or the FPC may crash and restart. Repeated crashes of PFE processing can result in an extended denial of service condition. This issue only affects the following platforms: (1) EX2200, EX3300, XRE200 (2) MX Series routers with MPC7E/8E/9E PFEs installed, and only if 'extended-statistics' are enabled under the [edit chassis] configuration. Affected releases are Juniper Networks Junos OS 14.1 prior to 14.1R8-S5, 14.1R9 on MX Series; 14.1X53 prior to 14.1X53-D46, 14.1X53-D50 on EX2200, EX3300, XRE200; 14.2 prior to 14.2R7-S9, 14.2R8 on MX Series; 15.1 prior to 15.1F5-S8, 15.1F6-S8, 15.1R5-S3, 15.1R6 on MX Series; 16.1 prior to 16.1R4-S5, 16.1R5, 16.1R6 on MX Series; 16.1X65 prior to 16.1X65-D45 on EX2200, EX3300, XRE200; 16.2 prior to 16.2R2-S1, 16.2R3 on MX Series; 17.1 prior to 17.1R2-S2, 17.1R3 on MX Series; 17.2 prior to 17.2R1-S3, 17.2R2 on MX Series; 17.2X75 prior to 17.2X75-D50 on MX Series; 17.3 prior to 17.3R1-S1, 17.3R2 on MX Series. No other Juniper Networks products or platforms are affected by this issue.

Unspecified vulnerability in Oracle MySQL Server 5.5.39 and earlier, and 5.6.20 and earlier, allows remote attackers to affect availability via vectors related to CLIENT:SSL:yaSSL, a different vulnerability than CVE-2014-6494.

The rpd daemon in Juniper Junos OS before 12.1X44-D60, 12.1X46 before 12.1X46-D45, 12.1X47 before 12.1X47-D30, 12.3 before 12.3R9, 12.3X48 before 12.3X48-D20, 13.2 before 13.2R7, 13.2X51 before 13.2X51-D40, 13.3 before 13.3R6, 14.1 before 14.1R4, and 14.2 before 14.2R2, when configured with BGP-based L2VPN or VPLS, allows remote attackers to cause a denial of service (daemon restart) via a crafted L2VPN family BGP update.

Juniper Junos OS before 12.1X46-D50, 12.1X47 before 12.1X47-D23, 12.3X48 before 12.3X48-D25, and 15.1X49 before 15.1X49-D40 on a High-End SRX-Series chassis system with one or more Application Layer Gateways (ALGs) enabled allow remote attackers to cause a denial of service (CPU consumption, fab link failure, or flip-flop failovers) via vectors related to in-transit traffic matching ALG rules.

named in ISC BIND 9.x before 9.9.8-P4 and 9.10.x before 9.10.3-P4 does not properly handle DNAME records when parsing fetch reply messages, which allows remote attackers to cause a denial of service (assertion failure and daemon exit) via a malformed packet to the rndc (aka control channel) interface, related to alist.c and sexpr.c.

Juniper Junos OS 14.1X53 before 14.1X53-D30 on QFX Series switches allows remote attackers to cause a denial of service (PFE panic) via a high rate of unspecified VXLAN packets.

On Juniper Networks products or platforms running Junos OS 11.4 prior to 11.4R13-S3, 12.1X46 prior to 12.1X46-D60, 12.3 prior to 12.3R12-S2 or 12.3R13, 12.3X48 prior to 12.3X48-D40, 13.2X51 prior to 13.2X51-D40, 13.3 prior to 13.3R10, 14.1 prior to 14.1R8, 14.1X53 prior to 14.1X53-D12 or 14.1X53-D35, 14.1X55 prior to 14.1X55-D35, 14.2 prior to 14.2R7, 15.1 prior to 15.1F6 or 15.1R3, 15.1X49 prior to 15.1X49-D60, 15.1X53 prior to 15.1X53-D30 and DHCPv6 enabled, when a crafted DHCPv6 packet is received from a subscriber, jdhcpd daemon crashes and restarts. Repeated crashes of the jdhcpd process may constitute an extended denial of service condition for subscribers attempting to obtain IPv6 addresses.

A Junos device with VPLS routing-instances configured on one or more interfaces may be susceptible to an mbuf leak when processing a specific MPLS packet. Approximately 1 mbuf is leaked per each packet processed. The number of mbufs is platform dependent. The following command provides the number of mbufs that are currently in use and maximum number of mbufs that can be allocated on a platform: > show system buffers 2437/3143/5580 mbufs in use (current/cache/total) Once the device runs out of mbufs it will become inaccessible and a restart will be required. This issue only affects end devices, transit devices are not affected. Affected releases are Juniper Networks Junos OS with VPLS configured running: 12.1X46 versions prior to 12.1X46-D76; 12.3X48 versions prior to 12.3X48-D66, 12.3X48-D70; 14.1 versions prior to 14.1R9; 14.1X53 versions prior to 14.1X53-D47; 14.2 versions prior to 14.2R8; 15.1 versions prior to 15.1F2-S19, 15.1F6-S10, 15.1R4-S9, 15.1R5-S7, 15.1R6-S4, 15.1R7; 15.1X49 versions prior to 15.1X49-D131, 15.1X49-D140; 15.1X53 versions prior to 15.1X53-D58 on EX2300/EX3400; 15.1X53 versions prior to 15.1X53-D233 on QFX5200/QFX5110; 15.1X53 versions prior to 15.1X53-D471 on NFX; 15.1X53 versions prior to 15.1X53-D66 on QFX10; 16.1 versions prior to 16.1R3-S8, 16.1R4-S6, 16.1R5; 16.2 versions prior to 16.2R1-S6, 16.2R2-S5, 16.2R3; 17.1 versions prior to 17.1R1-S7, 17.1R2-S6, 17.1R3; 17.2 versions prior to 17.2R1-S5, 17.2R2.

The Juniper Enhanced jdhcpd daemon may experience high CPU utilization, or crash and restart upon receipt of an invalid IPv6 UDP packet. Both high CPU utilization and repeated crashes of the jdhcpd daemon can result in a denial of service as DHCP service is interrupted. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS 14.1X53 prior to 14.1X53-D12, 14.1X53-D38, 14.1X53-D40 on QFX, EX, QFabric System; 15.1 prior to 15.1F2-S18, 15.1R4 on all products and platforms; 15.1X49 prior to 15.1X49-D80 on SRX; 15.1X53 prior to 15.1X53-D51, 15.1X53-D60 on NFX, QFX, EX.

When the "Intrusion Detection Service" (IDS) feature is configured on Juniper Networks MX series with a dynamic firewall filter using IPv6 source or destination prefix, it may incorrectly match the prefix as /32, causing the filter to block unexpected traffic. This issue affects only IPv6 prefixes when used as source and destination. This issue affects MX Series devices using MS-MPC, MS-MIC or MS-SPC3 service cards with IDS service configured. This issue affects: Juniper Networks Junos OS 17.3 versions prior to 17.3R3-S10 on MX Series; 17.4 versions prior to 17.4R3-S3 on MX Series; 18.1 versions prior to 18.1R3-S11 on MX Series; 18.2 versions prior to 18.2R3-S6 on MX Series; 18.3 versions prior to 18.3R3-S4 on MX Series; 18.4 versions prior to 18.4R3-S6 on MX Series; 19.1 versions prior to 19.1R2-S2, 19.1R3-S3 on MX Series; 19.2 versions prior to 19.2R3-S1 on MX Series; 19.3 versions prior to 19.3R2-S5, 19.3R3-S1 on MX Series; 19.4 versions prior to 19.4R3 on MX Series; 20.1 versions prior to 20.1R2 on MX Series; 20.2 versions prior to 20.2R2 on MX Series;

On Juniper Networks Junos OS devices configured with BGP origin validation using Resource Public Key Infrastructure (RPKI) receipt of a specific packet from the RPKI cache server may cause routing process daemon (RPD) to crash and restart, creating a Denial of Service (DoS) condition. Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS 17.3 versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S8, 18.4R3-S8; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R2-S4, 19.4R3-S3; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R2; 20.4 versions prior to 20.4R2. Juniper Networks Junos OS Evolved All versions prior to 20.4R2-S2-EVO.