A vulnerability in the Address Resolution Protocol (ARP) implementation of Cisco IOS XR Software could allow an unauthenticated, adjacent attacker to trigger a broadcast storm, leading to a denial of service (DoS) condition on an affected device. This vulnerability is due to how Cisco IOS XR Software processes a high, sustained rate of ARP traffic hitting the management interface. Under certain conditions, an attacker could exploit this vulnerability by sending an excessive amount of traffic to the management interface of an affected device, overwhelming its ARP processing capabilities. A successful exploit could result in degraded device performance, loss of management connectivity, and complete unresponsiveness of the system, leading to a DoS condition.
A vulnerability in the Control and Provisioning of Wireless Access Points (CAPWAP) protocol implementation of Cisco Aironet and Catalyst 9100 Access Points (APs) could allow an unauthenticated, adjacent attacker to cause an affected device to restart unexpectedly, resulting in a denial of service (DoS) condition. The vulnerability is due to improper resource management during CAPWAP message processing. An attacker could exploit this vulnerability by sending a high volume of legitimate wireless management frames within a short time to an affected device. A successful exploit could allow the attacker to cause a device to restart unexpectedly, resulting in a DoS condition for clients associated with the AP.
A vulnerability in the ARP packet processing of Cisco Adaptive Security Appliance (ASA) Software and Cisco Firepower Threat Defense (FTD) Software for Cisco Firepower 2100 Series Security Appliances could allow an unauthenticated, adjacent attacker to cause an affected device to reload, resulting in a denial of service (DoS) condition on an affected device. The vulnerability is due to incorrect processing of ARP packets received by the management interface of an affected device. An attacker could exploit this vulnerability by sending a series of unicast ARP packets in a short timeframe that would reach the management interface of an affected device. A successful exploit could allow the attacker to consume resources on an affected device, which would prevent the device from sending internal system keepalives and eventually cause the device to reload, resulting in a denial of service (DoS) condition.
Multiple vulnerabilities in the implementation of the Cisco Discovery Protocol and Link Layer Discovery Protocol (LLDP) for Cisco Video Surveillance 7000 Series IP Cameras could allow an unauthenticated, adjacent attacker to cause a memory leak, which could lead to a denial of service (DoS) condition on an affected device. These vulnerabilities are due to incorrect processing of certain Cisco Discovery Protocol and LLDP packets at ingress time. An attacker could exploit these vulnerabilities by sending crafted Cisco Discovery Protocol or LLDP packets to an affected device. A successful exploit could allow the attacker to cause the affected device to continuously consume memory, which could cause the device to crash and reload, resulting in a DoS condition. Note: Cisco Discovery Protocol and LLDP are Layer 2 protocols. To exploit these vulnerabilities, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent).
Multiple vulnerabilities in the implementation of the Cisco Discovery Protocol and Link Layer Discovery Protocol (LLDP) for Cisco Video Surveillance 7000 Series IP Cameras could allow an unauthenticated, adjacent attacker to cause a memory leak, which could lead to a denial of service (DoS) condition on an affected device. These vulnerabilities are due to incorrect processing of certain Cisco Discovery Protocol and LLDP packets at ingress time. An attacker could exploit these vulnerabilities by sending crafted Cisco Discovery Protocol or LLDP packets to an affected device. A successful exploit could allow the attacker to cause the affected device to continuously consume memory, which could cause the device to crash and reload, resulting in a DoS condition. Note: Cisco Discovery Protocol and LLDP are Layer 2 protocols. To exploit these vulnerabilities, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent).
A vulnerability in the 802.11r Fast Transition feature set of Cisco IOS Access Points (APs) Software could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition on an affected device. The vulnerability is due to a corruption of certain timer mechanisms triggered by specific roaming events. This corruption will eventually cause a timer crash. An attacker could exploit this vulnerability by sending malicious reassociation events multiple times to the same AP in a short period of time, causing a DoS condition on the affected AP.
A vulnerability in the Cisco Discovery Protocol (CDP) module of Cisco IOS XE Software Releases 16.6.1 and 16.6.2 could allow an unauthenticated, adjacent attacker to cause a memory leak that may lead to a denial of service (DoS) condition. The vulnerability is due to incorrect processing of certain CDP packets. An attacker could exploit this vulnerability by sending certain CDP packets to an affected device. A successful exploit could cause an affected device to continuously consume memory and eventually result in a memory allocation failure that leads to a crash, triggering a reload of the affected device.
A vulnerability in the Cisco Discovery Protocol of Cisco Video Surveillance 8000 Series IP Cameras could allow an unauthenticated, adjacent attacker to cause a memory leak, which could lead to a denial of service (DoS) condition on an affected device. The vulnerability is due to incorrect processing of certain Cisco Discovery Protocol packets. An attacker could exploit this vulnerability by sending certain Cisco Discovery Protocol packets to an affected device. A successful exploit could allow the attacker to cause the affected device to continuously consume memory, which could cause the device to crash and reload, resulting in a DOS condition. Note: Cisco Discovery Protocol is a Layer 2 protocol. To exploit this vulnerability, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent).
A vulnerability in the WLAN Local Profiling feature of Cisco IOS XE Wireless Controller Software for the Cisco Catalyst 9000 Family could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition on an affected device. The vulnerability is due to incorrect parsing of HTTP packets while performing HTTP-based endpoint device classifications. An attacker could exploit this vulnerability by sending a crafted HTTP packet to an affected device. A successful exploit could cause an affected device to reboot, resulting in a DoS condition.
A vulnerability in the PROFINET handler for Link Layer Discovery Protocol (LLDP) messages of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, adjacent attacker to cause a crash on an affected device, resulting in a denial of service (DoS) condition. The vulnerability is due to insufficient validation of LLDP messages in the PROFINET LLDP message handler. An attacker could exploit this vulnerability by sending a malicious LLDP message to an affected device. A successful exploit could allow the attacker to cause the affected device to reload.
A vulnerability in the PROFINET feature of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, adjacent attacker to cause an affected device to crash and reload, resulting in a denial of service (DoS) condition on the device. The vulnerability is due to insufficient processing logic for crafted PROFINET packets that are sent to an affected device. An attacker could exploit this vulnerability by sending crafted PROFINET packets to an affected device for processing. A successful exploit could allow the attacker to cause the device to crash and reload, resulting in a DoS condition on the device.
A vulnerability in the Cisco Discovery Protocol of Cisco Video Surveillance 8000 Series IP Cameras could allow an unauthenticated, adjacent attacker to cause a memory leak, which could lead to a denial of service (DoS) condition on an affected device. The vulnerability is due to incorrect processing of certain Cisco Discovery Protocol packets. An attacker could exploit this vulnerability by sending certain Cisco Discovery Protocol packets to an affected device. A successful exploit could allow the attacker to cause the affected device to continuously consume memory, which could cause the device to crash and reload, resulting in a DOS condition. Note: Cisco Discovery Protocol is a Layer 2 protocol. To exploit this vulnerability, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent).
Multiple vulnerabilities in the Control and Provisioning of Wireless Access Points (CAPWAP) protocol processing of Cisco IOS XE Software for Cisco Catalyst 9800 Series Wireless Controllers could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition of an affected device. These vulnerabilities are due to insufficient validation of CAPWAP packets. An attacker could exploit these vulnerabilities by sending a malformed CAPWAP packet to an affected device. A successful exploit could allow the attacker to cause the affected device to crash and reload, resulting in a DoS condition on the affected device.
A vulnerability in the Cisco Nexus 9000 Series Platform Leaf Switches for Application Centric Infrastructure (ACI) could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition on the affected device. This vulnerability affects Cisco Nexus 9000 Series Leaf Switches (TOR) - ACI Mode and Cisco Application Policy Infrastructure Controller (APIC). More Information: CSCuy93241. Known Affected Releases: 11.2(2x) 11.2(3x) 11.3(1x) 11.3(2x) 12.0(1x). Known Fixed Releases: 11.2(2i) 11.2(2j) 11.2(3f) 11.2(3g) 11.2(3h) 11.2(3l) 11.3(0.236) 11.3(1j) 11.3(2i) 11.3(2j) 12.0(1r).
The DHCP Relay implementation in Cisco Adaptive Security Appliance (ASA) Software 8.4.7.29 and 9.1.7.4 allows remote attackers to cause a denial of service (interface wedge) via a crafted rate of DHCP packet transmission, aka Bug ID CSCuy66942.
The rate-limit feature in the 802.11 protocol implementation on Cisco Aironet 1800, 2800, and 3800 devices with software before 8.2.121.0 and 8.3.x before 8.3.102.0 allows remote attackers to cause a denial of service (device reload) via crafted 802.11 frames, aka Bug ID CSCva06192.
The Aggregated MAC Protocol Data Unit (AMPDU) implementation on Cisco Aironet 1800, 2800, and 3800 devices with software before 8.2.121.0 and 8.3.x before 8.3.102.0 allows remote attackers to cause a denial of service (device reload) via a crafted AMPDU header, aka Bug ID CSCuz56288.
Cisco Videoscape Session Resource Manager (VSRM) allows remote attackers to cause a denial of service (device restart) by sending a traffic flood to upstream devices, aka Bug ID CSCva01813.
Cisco IOS 15.2(1)T1.11 and 15.2(2)TST allows remote attackers to cause a denial of service (device crash) via a crafted LLDP packet, aka Bug ID CSCun63132.
Cisco IOS 15.0(2)SG5, 15.1(2)SG3, 15.2(1)E, 15.3(3)S, and 15.4(1.13)S allows remote attackers to cause a denial of service (device crash) via a crafted LLDP packet, aka Bug ID CSCun66735.
dot11t/t_if_dot11_hal_ath.c in Cisco IOS 12.3, 12.4, 15.0, and 15.1 allows remote attackers to cause a denial of service (assertion failure and reboot) via 802.11 wireless traffic, as demonstrated by a video call from Apple iOS 5.0 on an iPhone 4S, aka Bug ID CSCtt94391.
Cisco IOS before 15.1(1)SY on ASR 1000 devices, when Multicast Listener Discovery (MLD) tracking is enabled for IPv6, allows remote attackers to cause a denial of service (device reload) via crafted MLD packets, aka Bug ID CSCtz28544.
Cisco NX-OS 5.2 and 6.1 on Nexus 7000 series switches allows remote attackers to cause a denial of service (process crash or packet loss) via a large number of ARP packets, aka Bug ID CSCtr44822.
A vulnerability in the implementation of the cluster feature of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, adjacent attacker to trigger a denial of service (DoS) condition on an affected device. The vulnerability is due to improper input validation when handling Cluster Management Protocol (CMP) messages. An attacker could exploit this vulnerability by sending a malicious CMP message to an affected device. A successful exploit could allow the attacker to cause the switch to crash and reload or to hang, resulting in a DoS condition. If the switch hangs it will not reboot automatically, and it will need to be power cycled manually to recover.
A vulnerability in the 802.11 association frame validation of Cisco Catalyst 9100 Series Access Points (APs) could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to insufficient input validation of certain parameters within association request frames received by the AP. An attacker could exploit this vulnerability by sending a crafted 802.11 association request to a nearby device. An exploit could allow the attacker to unexpectedly reload the device, resulting in a DoS condition.
A vulnerability in the Open Shortest Path First version 3 (OSPFv3) implementation in Cisco IOS and IOS XE Software could allow an unauthenticated, adjacent attacker to cause an affected device to reload. The vulnerability is due to incorrect handling of specific OSPFv3 packets. An attacker could exploit this vulnerability by sending crafted OSPFv3 Link-State Advertisements (LSA) to an affected device. An exploit could allow the attacker to cause an affected device to reload, leading to a denial of service (DoS) condition.
A vulnerability in the Cisco Discovery Protocol service of Cisco FXOS Software and Cisco NX-OS Software could allow an unauthenticated, adjacent attacker to cause the service to restart, resulting in a denial of service (DoS) condition. This vulnerability is due to improper handling of Cisco Discovery Protocol messages that are processed by the Cisco Discovery Protocol service. An attacker could exploit this vulnerability by sending a series of malicious Cisco Discovery Protocol messages to an affected device. A successful exploit could allow the attacker to cause the Cisco Discovery Protocol service to fail and restart. In rare conditions, repeated failures of the process could occur, which could cause the entire device to restart.
A vulnerability in Simple Network Management Protocol (SNMP) trap generation for wireless clients of Cisco IOS XE Wireless Controller Software for the Catalyst 9000 Family could allow an unauthenticated, adjacent attacker to cause an affected device to unexpectedly reload, resulting in a denial of service (DoS) condition on the device. This vulnerability is due to a lack of input validation of the information used to generate an SNMP trap related to a wireless client connection event. An attacker could exploit this vulnerability by sending an 802.1x packet with crafted parameters during the wireless authentication setup phase of a connection. A successful exploit could allow the attacker to cause the device to reload, resulting in a DoS condition.
A vulnerability in the Cisco Discovery Protocol of Cisco Unified Communications Manager (Unified CM) and Cisco Unified Communications Manager Session Management Edition (Unified CM SME) could allow an unauthenticated, adjacent attacker to cause a kernel panic on an affected system, resulting in a denial of service (DoS) condition. This vulnerability is due to incorrect processing of certain Cisco Discovery Protocol packets. An attacker could exploit this vulnerability by continuously sending certain Cisco Discovery Protocol packets to an affected device. A successful exploit could allow the attacker to cause a kernel panic on the system that is running the affected software, resulting in a DoS condition.
A vulnerability in the implementation of IPv6 VPN over MPLS (6VPE) with Zone-Based Firewall (ZBFW) of Cisco IOS XE Software could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to improper error handling of an IPv6 packet that is forwarded from an MPLS and ZBFW-enabled interface in a 6VPE deployment. An attacker could exploit this vulnerability by sending a crafted IPv6 packet sourced from a device on the IPv6-enabled virtual routing and forwarding (VRF) interface through the affected device. A successful exploit could allow the attacker to reload the device, resulting in a DoS condition.
A vulnerability in the authentication functionality of Cisco Wireless LAN Controller (WLC) AireOS Software could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to insufficient error validation. An attacker could exploit this vulnerability by sending crafted packets to an affected device. A successful exploit could allow the attacker to cause the wireless LAN controller to crash, resulting in a DoS condition. Note: This vulnerability affects only devices that have Federal Information Processing Standards (FIPS) mode enabled.
A vulnerability in the integrated wireless access point (AP) packet processing of the Cisco 1000 Series Connected Grid Router (CGR1K) could allow an unauthenticated, adjacent attacker to cause a denial of service condition on an affected device. This vulnerability is due to insufficient input validation of received traffic. An attacker could exploit this vulnerability by sending crafted traffic to an affected device. A successful exploit could allow the attacker to cause the integrated AP to stop processing traffic, resulting in a DoS condition. It may be necessary to manually reload the CGR1K to restore AP operation.
A vulnerability in the HTTP-based client profiling feature of Cisco IOS XE Software for Wireless LAN Controllers (WLCs) could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to insufficient input validation of received traffic. An attacker could exploit this vulnerability by sending crafted traffic through a wireless access point. A successful exploit could allow the attacker to cause CPU utilization to increase, which could result in a DoS condition on an affected device and could cause new wireless client associations to fail. Once the offending traffic stops, the affected system will return to an operational state and new client associations will succeed.
The ARP implementation in Cisco NX-OS on Nexus 1000V devices for VMware vSphere 5.2(1)SV3(1.4), Nexus 3000 devices 7.3(0)ZD(0.47), Nexus 4000 devices 4.1(2)E1, Nexus 9000 devices 7.3(0)ZD(0.61), and MDS 9000 devices 7.0(0)HSK(0.353) and SAN-OS NX-OS on MDS 9000 devices 7.0(0)HSK(0.353) allows remote attackers to cause a denial of service (ARP process restart) via crafted packet-header fields, aka Bug ID CSCut25292.
The Neighbor Discovery (ND) protocol implementation in the IPv6 stack in Cisco IOS 15.3(3)S0.1 on ASR devices mishandles internal tables, which allows remote attackers to cause a denial of service (memory consumption or device crash) via a flood of crafted ND messages, aka Bug ID CSCup28217.
Cisco IOS 15.2(3)E and earlier and IOS XE 3.6(2)E and earlier allow remote attackers to cause a denial of service (functionality loss) via crafted Cisco Discovery Protocol (CDP) packets, aka Bug ID CSCuu25770.
A vulnerability in the 802.11r Fast Transition (FT) implementation for Cisco IOS Access Points (APs) Software could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition on an affected interface. The vulnerability is due to a lack of complete error handling condition for client authentication requests sent to a targeted interface configured for FT. An attacker could exploit this vulnerability by sending crafted authentication request traffic to the targeted interface, causing the device to restart unexpectedly.
A vulnerability in the implementation of Intermediate System–to–Intermediate System (IS–IS) routing protocol functionality in Cisco IOS XR Software could allow an unauthenticated attacker who is in the same IS-IS area to cause a denial of service (DoS) condition. The vulnerability is due to incorrect processing of IS–IS link-state protocol data units (PDUs). An attacker could exploit this vulnerability by sending specific link-state PDUs to an affected system to be processed. A successful exploit could allow the attacker to cause incorrect calculations used in the weighted remote shared risk link groups (SRLG) or in the IGP Flexible Algorithm. It could also cause tracebacks to the logs or potentially cause the receiving device to crash the IS–IS process, resulting in a DoS condition.
A vulnerability in Cisco IOS on Catalyst Switches and Nexus 9300 Series Switches could allow an unauthenticated, adjacent attacker to cause a Layer 2 network storm. More Information: CSCuu69332, CSCux07028. Known Affected Releases: 15.2(3)E. Known Fixed Releases: 12.2(50)SE4 12.2(50)SE5 12.2(50)SQ5 12.2(50)SQ6 12.2(50)SQ7 12.2(52)EY4 12.2(52)SE1 12.2(53)EX 12.2(53)SE 12.2(53)SE1 12.2(53)SE2 12.2(53)SG10 12.2(53)SG11 12.2(53)SG2 12.2(53)SG9 12.2(54)SG1 12.2(55)EX3 12.2(55)SE 12.2(55)SE1 12.2(55)SE10 12.2(55)SE2 12.2(55)SE3 12.2(55)SE4 12.2(55)SE5 12.2(55)SE6 12.2(55)SE7 12.2(55)SE8 12.2(55)SE9 12.2(58)EZ 12.2(58)SE1 12.2(58)SE2 12.2(60)EZ 12.2(60)EZ1 12.2(60)EZ2 12.2(60)EZ3 12.2(60)EZ4 12.2(60)EZ5 12.2(60)EZ6 12.2(60)EZ7 12.2(60)EZ8 15.0(1)EY2 15.0(1)SE 15.0(1)SE2 15.0(1)SE3 15.0(2)EA 15.0(2)EB 15.0(2)EC 15.0(2)ED 15.0(2)EH 15.0(2)EJ 15.0(2)EJ1 15.0(2)EK1 15.0(2)EX 15.0(2)EX1 15.0(2)EX3 15.0(2)EX4 15.0(2)EX5 15.0(2)EY 15.0(2)EY1 15.0(2)EY2 15.0(2)EZ 15.0(2)SE 15.0(2)SE1 15.0(2)SE2 15.0(2)SE3 15.0(2)SE4 15.0(2)SE5 15.0(2)SE6 15.0(2)SE7 15.0(2)SE9 15.0(2)SG10 15.0(2)SG3 15.0(2)SG6 15.0(2)SG7 15.0(2)SG8 15.0(2)SG9 15.0(2a)EX5 15.1(2)SG 15.1(2)SG1 15.1(2)SG2 15.1(2)SG3 15.1(2)SG4 15.1(2)SG5 15.1(2)SG6 15.2(1)E 15.2(1)E1 15.2(1)E2 15.2(1)E3 15.2(1)EY 15.2(2)E 15.2(2)E3 15.2(2b)E.
The Adaptive Wireless Intrusion Prevention System (wIPS) feature on Cisco Wireless LAN Controller (WLC) devices before 8.0.140.0, 8.1.x and 8.2.x before 8.2.121.0, and 8.3.x before 8.3.102.0 allows remote attackers to cause a denial of service (device restart) via a malformed wIPS packet, aka Bug ID CSCuz40263.
A vulnerability in the Cluster Management Protocol (CMP) processing code in Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, adjacent attacker to trigger a denial of service (DoS) condition on an affected device. The vulnerability is due to insufficient input validation when processing CMP management packets. An attacker could exploit this vulnerability by sending malicious CMP management packets to an affected device. A successful exploit could cause the switch to crash, resulting in a DoS condition. The switch will reload automatically.
A vulnerability in the ingress traffic validation of Cisco IOS XE Software for Cisco Aggregation Services Router (ASR) 900 Route Switch Processor 3 (RSP3) could allow an unauthenticated, adjacent attacker to trigger a reload of an affected device, resulting in a denial of service (DoS) condition. The vulnerability exists because the software insufficiently validates ingress traffic on the ASIC used on the RSP3 platform. An attacker could exploit this vulnerability by sending a malformed OSPF version 2 (OSPFv2) message to an affected device. A successful exploit could allow the attacker to cause a reload of the iosd process, triggering a reload of the affected device and resulting in a DoS condition.
A vulnerability in the Easy Virtual Switching System (VSS) of Cisco IOS XE Software on Catalyst 4500 Series Switches could allow an unauthenticated, adjacent attacker to cause the switches to reload. The vulnerability is due to incomplete error handling when processing Cisco Discovery Protocol (CDP) packets used with the Easy Virtual Switching System. An attacker could exploit this vulnerability by sending a specially crafted CDP packet. An exploit could allow the attacker to cause the device to reload, resulting in a denial of service (DoS) condition.
A vulnerability in the handling of Inter-Access Point Protocol (IAPP) messages by Cisco Wireless LAN Controller (WLC) Software could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition. The vulnerability exist because the software improperly validates input on fields within IAPP messages. An attacker could exploit the vulnerability by sending malicious IAPP messages to an affected device. A successful exploit could allow the attacker to cause the Cisco WLC Software to reload, resulting in a DoS condition. Software versions prior to 8.2.170.0, 8.5.150.0, and 8.8.100.0 are affected.
A vulnerability in the handling of Inter-Access Point Protocol (IAPP) messages by Cisco Wireless LAN Controller (WLC) Software could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition. The vulnerability exist because the software improperly validates input on fields within IAPP messages. An attacker could exploit the vulnerability by sending malicious IAPP messages to an affected device. A successful exploit could allow the attacker to cause the Cisco WLC Software to reload, resulting in a DoS condition. Software versions prior to 8.2.170.0, 8.5.150.0, and 8.8.100.0 are affected.
A vulnerability in the Border Gateway Patrol (BGP) Multiprotocol Label Switching (MPLS)-based Ethernet VPN (EVPN) implementation of Cisco IOS XR Software could allow an unauthenticated, adjacent attacker to trigger a denial of service (DoS) condition on an affected device. The vulnerability is due to a logic error that occurs when the affected software processes specific EVPN routing information. An attacker could exploit this vulnerability by injecting malicious traffic patterns into the targeted EVPN network. A successful exploit could result in a crash of the l2vpn_mgr process on Provider Edge (PE) device members of the same EVPN instance (EVI). On each of the affected devices, a crash could lead to system instability and the inability to process or forward traffic through the device, resulting in a DoS condition that would require manual intervention to restore normal operating conditions.
A vulnerability in the Multiprotocol Label Switching (MPLS) Operations, Administration, and Maintenance (OAM) implementation of Cisco IOS XR Software for Cisco ASR 9000 Series Aggregation Services Routers could allow an unauthenticated, adjacent attacker to trigger a denial of service (DoS) condition on an affected device. The vulnerability is due to the incorrect handling of certain MPLS OAM packets. An attacker could exploit this vulnerability by sending malicious MPLS OAM packets to an affected device. A successful exploit could allow the attacker to cause the lspv_server process to crash. The crash could lead to system instability and the inability to process or forward traffic though the device, resulting in a DoS condition that require manual intervention to restore normal operating conditions.
A vulnerability in the handling of Inter-Access Point Protocol (IAPP) messages by Cisco Wireless LAN Controller (WLC) Software could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition. The vulnerability exist because the software improperly validates input on fields within IAPP messages. An attacker could exploit the vulnerability by sending malicious IAPP messages to an affected device. A successful exploit could allow the attacker to cause the Cisco WLC Software to reload, resulting in a DoS condition. Software versions prior to 8.2.170.0, 8.5.150.0, and 8.8.100.0 are affected.
A vulnerability in the 802.1X implementation for Cisco NX-OS Software could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition on an affected device. The vulnerability is due to incomplete input validation of Extensible Authentication Protocol over LAN (EAPOL) frames. An attacker could exploit this vulnerability by sending a crafted EAPOL frame to an interface on the targeted device. A successful exploit could allow the attacker to cause the Layer 2 (L2) forwarding process to restart multiple times, leading to a system-level restart of the device and a DoS condition. Note: This vulnerability affects only NX-OS devices configured with 802.1X functionality. Cisco Nexus 1000V Switch for VMware vSphere devices are affected in versions prior to 5.2(1)SV3(1.4b). Nexus 3000 Series Switches are affected in versions prior to 7.0(3)I7(4). Nexus 3500 Platform Switches are affected in versions prior to 7.0(3)I7(4). Nexus 2000, 5500, 5600, and 6000 Series Switches are affected in versions prior to 7.3(5)N1(1) and 7.1(5)N1(1b). Nexus 7000 and 7700 Series Switches are affected in versions prior to 8.2(3). Nexus 9000 Series Fabric Switches in ACI Mode are affected in versions prior to 13.2(1l). Nexus 9000 Series Switches in Standalone NX-OS Mode are affected in versions prior to 7.0(3)I7(4).
A vulnerability in the Cisco Discovery Protocol or Link Layer Discovery Protocol (LLDP) implementation for the Cisco IP Phone 7800 and 8800 Series could allow an unauthenticated, adjacent attacker to cause an affected phone to reload unexpectedly, resulting in a temporary denial of service (DoS) condition. The vulnerability is due to missing length validation of certain Cisco Discovery Protocol or LLDP packet header fields. An attacker could exploit this vulnerability by sending a malicious Cisco Discovery Protocol or LLDP packet to the targeted phone. A successful exploit could allow the attacker to cause the affected phone to reload unexpectedly, resulting in a temporary DoS condition. Versions prior to 12.6(1)MN80 are affected.