A vulnerability in the Link Layer Discovery Protocol (LLDP) feature for Cisco Nexus 9000 Series Fabric Switches in Application Centric Infrastructure (ACI) Mode could allow an unauthenticated, adjacent attacker to cause a memory leak, which could result in an unexpected reload of the device. This vulnerability is due to incorrect error checking when parsing ingress LLDP packets. An attacker could exploit this vulnerability by sending a steady stream of crafted LLDP packets to an affected device. A successful exploit could allow the attacker to cause a memory leak, which could result in a denial of service (DoS) condition when the device unexpectedly reloads. Note: This vulnerability cannot be exploited by transit traffic through the device. The crafted LLDP packet must be targeted to a directly connected interface, and the attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent). In addition, the attack surface for this vulnerability can be reduced by disabling LLDP on interfaces where it is not required.

Cisco Adaptive Security Appliance (ASA) Software, when DHCPv6 replay is configured, allows remote attackers to cause a denial of service (device reload) via a crafted DHCPv6 packet, aka Bug ID CSCun45520.

The packet driver in Cisco IOS allows remote attackers to cause a denial of service (device reload) via a series of (1) Virtual Switching Systems (VSS) or (2) Bidirectional Forwarding Detection (BFD) packets, aka Bug IDs CSCug41049 and CSCue61890.

A vulnerability in the Layer 2 Ethernet services of Cisco IOS XR Software could allow an unauthenticated, adjacent attacker to cause the line card network processor to reset, resulting in a denial of service (DoS) condition. This vulnerability is due to the incorrect handling of specific Ethernet frames that are received on line cards that have the Layer 2 services feature enabled. An attacker could exploit this vulnerability by sending specific Ethernet frames through an affected device. A successful exploit could allow the attacker to cause the ingress interface network processor to reset, resulting in a loss of traffic over the interfaces that are supported by the network processor. Multiple resets of the network processor would cause the line card to reset, resulting in a DoS condition.

A vulnerability in the implementation of Cisco Discovery Protocol functionality in Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, adjacent attacker to exhaust memory on an affected device, resulting in a denial of service (DoS) condition. The vulnerability is due to improper memory handling by the affected software when the software processes high rates of Cisco Discovery Protocol packets that are sent to a device. An attacker could exploit this vulnerability by sending a high rate of Cisco Discovery Protocol packets to an affected device. A successful exploit could allow the attacker to exhaust memory on the affected device, resulting in a DoS condition.

A vulnerability in the Layer 2 punt code of Cisco IOS XR Software running on Cisco ASR 9000 Series Aggregation Services Routers could allow an unauthenticated, adjacent attacker to cause the affected line card to reboot. This vulnerability is due to incorrect handling of specific Ethernet frames that cause a spin loop that can make the network processors unresponsive. An attacker could exploit this vulnerability by sending specific types of Ethernet frames on the segment where the affected line cards are attached. A successful exploit could allow the attacker to cause the affected line card to reboot.

A vulnerability in the Link Layer Discovery Protocol (LLDP) implementation for the Cisco Video Surveillance 7000 Series IP Cameras firmware could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition. This vulnerability is due to improper management of memory resources, referred to as a double free. An attacker could exploit this vulnerability by sending crafted LLDP packets to an affected device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition. Note: LLDP is a Layer 2 protocol. To exploit these vulnerabilities, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent).

A vulnerability in the WLAN Control Protocol (WCP) implementation for Cisco Aironet Access Point (AP) software could allow an unauthenticated, adjacent attacker to cause a reload of an affected device, resulting in a denial of service (DoS) condition. This vulnerability is due to incorrect error handling when an affected device receives an unexpected 802.11 frame. An attacker could exploit this vulnerability by sending certain 802.11 frames over the wireless network to an interface on an affected AP. A successful exploit could allow the attacker to cause a packet buffer leak. This could eventually result in buffer allocation failures, which would trigger a reload of the affected device.

A vulnerability in the Open Shortest Path First (OSPF) implementation of Cisco Adaptive Security Appliance (ASA) Software and Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, adjacent attacker to cause a reload of an affected device, resulting in a denial of service (DoS) condition. The vulnerability exists because the affected software improperly parses certain options in OSPF link-state advertisement (LSA) type 11 packets. An attacker could exploit this vulnerability by sending a crafted LSA type 11 OSPF packet to an affected device. A successful exploit could allow the attacker to cause a reload of the affected device, resulting in a DoS condition for client traffic that is traversing the device.

A vulnerability with the Ethernet VPN (EVPN) Layer 2 ingress packet processing of Cisco Nexus 3600 Platform Switches and Cisco Nexus 9500-R Series Switching Platforms could allow an unauthenticated, adjacent attacker to trigger a Layer 2 traffic loop. This vulnerability is due to a logic error when processing a crafted Layer 2 ingress frame. An attacker could exploit this vulnerability by sending a stream of crafted Ethernet frames through the targeted device. A successful exploit could allow the attacker to cause a Layer 2 Virtual eXtensible LAN (VxLAN) traffic loop, which, in turn, could result in a denial of service (DoS) condition. This Layer 2 loop could oversubscribe the bandwidth on network interfaces, which would result in all data plane traffic being dropped. To exploit this vulnerability, the attacker must be Layer 2-adjacent to the affected device. Note: To stop active exploitation of this vulnerability, manual intervention is required to both stop the crafted traffic and flap all involved network interfaces. For additional assistance if a Layer 2 loop that is related to this vulnerability is suspected, contact the Cisco Technical Assistance Center (TAC) or the proper support provider. 

A vulnerability in the implementation of a protocol in Cisco Integrated Services Routers Generation 2 (ISR G2) Routers running Cisco IOS 15.0 through 15.6 could allow an unauthenticated, adjacent attacker to cause an affected device to reload, resulting in a denial of service (DoS) condition. The vulnerability is due to a misclassification of Ethernet frames. An attacker could exploit this vulnerability by sending a crafted Ethernet frame to an affected device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition. Cisco Bug IDs: CSCvc03809.

A vulnerability in 802.11 association request frame processing for the Cisco Aironet 1560, 2800, and 3800 Series Access Points could allow an unauthenticated, Layer 2 radio frequency (RF) adjacent attacker to cause the Access Point (AP) to reload, resulting in a denial of service (DoS) condition. The vulnerability is due to insufficient frame validation of the 802.11 association request. An attacker could exploit this vulnerability by sending a malformed 802.11 association request to the targeted device. An exploit could allow the attacker to cause the AP to reload, resulting in a DoS condition while the AP is reloading. This vulnerability affects the following Cisco products running either the Lightweight AP Software or Mobility Express image: Aironet 1560 Series Access Points, Aironet 2800 Series Access Points, Aironet 3800 Series Access Points. Note: The Cisco Aironet 1560 Series Access Point device is supported as of release 8.3.112.0. Cisco Bug IDs: CSCve12189.

A vulnerability in the implementation of the Intermediate System–to–Intermediate System (IS–IS) routing protocol functionality in Cisco IOS XR Software could allow an unauthenticated attacker who is in the same IS–IS area to cause a denial of service (DoS) condition. The vulnerability is due to incorrect processing of crafted IS–IS link-state protocol data units (PDUs). An attacker could exploit this vulnerability by sending a crafted link-state PDU to an affected system to be processed. A successful exploit could allow the attacker to cause all routers within the IS–IS area to unexpectedly restart the IS–IS process, resulting in a DoS condition. This vulnerability affects Cisco devices if they are running a vulnerable release of Cisco IOS XR Software earlier than Release 6.6.3 and are configured with the IS–IS routing protocol. Cisco has confirmed that this vulnerability affects both Cisco IOS XR 32-bit Software and Cisco IOS XR 64-bit Software.

The IPv6 implementation in Cisco NX-OS does not properly handle neighbor-table adjacencies, which allows remote attackers to cause a denial of service (NS processing outage) via a series of malformed packets, aka Bug ID CSCtd15904.

The IP Device Tracking (IPDT) feature in Cisco IOS and IOS XE allows remote attackers to cause a denial of service (IPDT AVL corruption and device reload) via a crafted sequence of ARP packets, aka Bug ID CSCuh38133.

The mDNS snooping functionality on Cisco Wireless LAN Controller (WLC) devices with software 7.4.1.54 and earlier does not properly manage buffers, which allows remote authenticated users to cause a denial of service (device reload) via crafted mDNS packets, aka Bug ID CSCue04153.

The Ethernet frame-forwarding implementation in Cisco NX-OS on Nexus 7000 devices allows remote attackers to cause a denial of service (forwarding loop and service outage) via a crafted frame, aka Bug ID CSCug47098.

The HTTP Profiler on the Cisco Aironet Access Point with software 15.2 and earlier does not properly manage buffers, which allows remote attackers to cause a denial of service (device reload) via crafted HTTP requests, aka Bug ID CSCuc62460.

Cisco ASR 1000 devices with software before 3.8S, when BDI routing is enabled, allow remote attackers to cause a denial of service (device reload) via crafted (1) broadcast or (2) multicast ICMP packets with fragmentation, aka Bug ID CSCub55948.

Cisco NX-OS 5.2 and 6.1 on Nexus 7000 series switches allows remote attackers to cause a denial of service (process crash or packet loss) via a large number of ARP packets, aka Bug ID CSCtr44822.

dot11t/t_if_dot11_hal_ath.c in Cisco IOS 12.3, 12.4, 15.0, and 15.1 allows remote attackers to cause a denial of service (assertion failure and reboot) via 802.11 wireless traffic, as demonstrated by a video call from Apple iOS 5.0 on an iPhone 4S, aka Bug ID CSCtt94391.

Cisco IOS before 15.1(1)SY on ASR 1000 devices, when Multicast Listener Discovery (MLD) tracking is enabled for IPv6, allows remote attackers to cause a denial of service (device reload) via crafted MLD packets, aka Bug ID CSCtz28544.

A vulnerability in the multicast DNS (mDNS) gateway feature of Cisco Aironet Series Access Points Software could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to insufficient input validation of incoming mDNS traffic. An attacker could exploit this vulnerability by sending a crafted mDNS packet to an affected device through a wireless network that is configured in FlexConnect local switching mode or through a wired network on a configured mDNS VLAN. A successful exploit could allow the attacker to cause the access point (AP) to reboot, resulting in a DoS condition.

Multiple vulnerabilities exist in the Link Layer Discovery Protocol (LLDP) implementation for Cisco Small Business RV Series Routers. An unauthenticated, adjacent attacker could execute arbitrary code or cause an affected router to leak system memory or reload. A memory leak or device reload would cause a denial of service (DoS) condition on an affected device. For more information about these vulnerabilities, see the Details section of this advisory. Note: LLDP is a Layer 2 protocol. To exploit these vulnerabilities, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent).

A vulnerability in the DECnet Phase IV and DECnet/OSI protocol processing of Cisco IOS XE Software could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition on an affected device. The vulnerability is due to insufficient input validation of DECnet traffic that is received by an affected device. An attacker could exploit this vulnerability by sending DECnet traffic to an affected device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition.

A vulnerability in the IPv6 protocol handling of the management interfaces of Cisco IOS XR Software could allow an unauthenticated, adjacent attacker to cause an IPv6 flood on the management interface network of an affected device. The vulnerability exists because the software incorrectly forwards IPv6 packets that have an IPv6 node-local multicast group address destination and are received on the management interfaces. An attacker could exploit this vulnerability by connecting to the same network as the management interfaces and injecting IPv6 packets that have an IPv6 node-local multicast group address destination. A successful exploit could allow the attacker to cause an IPv6 flood on the corresponding network. Depending on the number of Cisco IOS XR Software nodes on that network segment, exploitation could cause excessive network traffic, resulting in network degradation or a denial of service (DoS) condition.

A vulnerability in the Cisco Discovery Protocol implementation for Cisco Video Surveillance 8000 Series IP Cameras could allow an unauthenticated, adjacent attacker to cause an affected IP camera to reload. This vulnerability is due to missing checks when processing Cisco Discovery Protocol messages. An attacker could exploit this vulnerability by sending a malicious Cisco Discovery Protocol packet to an affected IP camera. A successful exploit could allow the attacker to cause the affected IP camera to reload unexpectedly, resulting in a denial of service (DoS) condition. Note: Cisco Discovery Protocol is a Layer 2 protocol. To exploit this vulnerability, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent).

A vulnerability in Cisco Nexus 9000 Series Fabric Switches in ACI mode could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to insufficient validation when processing specific Ethernet frames. An attacker could exploit this vulnerability by sending a crafted Ethernet frame to the management interface of an affected device. A successful exploit could allow the attacker to cause the device to reload unexpectedly, resulting in a DoS condition. Note: Only the out-of-band (OOB) management interface is affected.

A vulnerability in the Intermediate System-to-Intermediate System (IS-IS) multi-instance routing feature of Cisco IOS XR Software could allow an unauthenticated, adjacent attacker to cause the IS-IS process to restart unexpectedly. This vulnerability is due to insufficient input validation of ingress IS-IS packets. An attacker could exploit this vulnerability by sending crafted IS-IS packets to an affected device after forming an adjacency. A successful exploit could allow the attacker to cause the IS-IS process to restart unexpectedly, resulting in a temporary loss of connectivity to advertised networks and a denial of service (DoS) condition. Note: The IS-IS protocol is a routing protocol. To exploit this vulnerability, an attacker must be Layer 2-adjacent to the affected device and must have formed an adjacency.  

A vulnerability in the Link Layer Discovery Protocol (LLDP) feature of Cisco NX-OS Software could allow an unauthenticated, adjacent attacker to cause the LLDP process to restart, which could cause an affected device to reload unexpectedly. This vulnerability is due to improper handling of specific fields in an LLDP frame. An attacker could exploit this vulnerability by sending a crafted LLDP packet to an interface of an affected device. A successful exploit could allow the attacker to cause the device to reload, resulting in a denial of service (DoS) condition. Note: LLDP is a Layer 2 link protocol. To exploit this vulnerability, an attacker would need to be directly connected to an interface of an affected device, either physically or logically (for example, through a Layer 2 Tunnel configured to transport the LLDP protocol).

A vulnerability in the TLS library of Cisco IOS XE Software could allow an unauthenticated, adjacent attacker to exhaust the available memory of an affected device. This vulnerability is due to improper management of memory resources during TLS connection setup. An attacker could exploit this vulnerability by repeatedly triggering the conditions that cause the memory increase. This could be done in a variety of ways, such as by repeatedly attempting Extensible Authentication Protocol (EAP) authentication when local EAP is enabled on an affected device or by using a machine-in-the-middle attack and resetting TLS connections between the affected device and other devices. A successful exploit could allow the attacker to exhaust the available memory on an affected device, resulting in an unexpected reload and a denial of service (DoS) condition.

A vulnerability in the Ethernet packet handling of Cisco Aironet Access Points (APs) Software could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition on an affected device. The vulnerability is due to insufficient input validation. An attacker could exploit this vulnerability by connecting as a wired client to the Ethernet interface of an affected device and sending a series of specific packets within a short time frame. A successful exploit could allow the attacker to cause a NULL pointer access that results in a reload of the affected device.

A vulnerability in Simple Network Management Protocol (SNMP) trap generation for wireless clients of the Cisco IOS XE Wireless Controller Software for the Cisco Catalyst 9000 Family could allow an unauthenticated, adjacent attacker to cause the device to unexpectedly reload, causing a denial of service (DoS) condition on an affected device. The vulnerability is due to the lack of input validation of the information used to generate an SNMP trap in relation to a wireless client connection. An attacker could exploit this vulnerability by sending an 802.1x packet with crafted parameters during the wireless authentication setup phase of a connection. A successful exploit could allow the attacker to cause the device to reload, causing a DoS condition.

Multiple vulnerabilities in the Control and Provisioning of Wireless Access Points (CAPWAP) protocol processing of Cisco IOS XE Software for Cisco Catalyst 9800 Series Wireless Controllers could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition of an affected device. These vulnerabilities are due to insufficient validation of CAPWAP packets. An attacker could exploit these vulnerabilities by sending a malformed CAPWAP packet to an affected device. A successful exploit could allow the attacker to cause the affected device to crash and reload, resulting in a DoS condition on the affected device.

Multiple vulnerabilities in the Control and Provisioning of Wireless Access Points (CAPWAP) protocol processing of Cisco IOS XE Software for Cisco Catalyst 9800 Series Wireless Controllers could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition of an affected device. These vulnerabilities are due to insufficient validation of CAPWAP packets. An attacker could exploit these vulnerabilities by sending a malformed CAPWAP packet to an affected device. A successful exploit could allow the attacker to cause the affected device to crash and reload, resulting in a DoS condition on the affected device.

Multiple vulnerabilities in the Control and Provisioning of Wireless Access Points (CAPWAP) protocol processing of Cisco IOS XE Software for Cisco Catalyst 9800 Series Wireless Controllers could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition of an affected device. These vulnerabilities are due to insufficient validation of CAPWAP packets. An attacker could exploit these vulnerabilities by sending a malformed CAPWAP packet to an affected device. A successful exploit could allow the attacker to cause the affected device to crash and reload, resulting in a DoS condition on the affected device.

A vulnerability in Cisco IOS XE Software could allow an unauthenticated, adjacent attacker to cause a device to reload. The vulnerability is due to incorrect handling of certain valid, but not typical, Ethernet frames. An attacker could exploit this vulnerability by sending the Ethernet frames onto the Ethernet segment. A successful exploit could allow the attacker to cause the device to reload, resulting in a denial of service (DoS) condition.

Multiple vulnerabilities in the Control and Provisioning of Wireless Access Points (CAPWAP) protocol processing of Cisco IOS XE Software for Cisco Catalyst 9800 Series Wireless Controllers could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition of an affected device. These vulnerabilities are due to insufficient validation of CAPWAP packets. An attacker could exploit these vulnerabilities by sending a malformed CAPWAP packet to an affected device. A successful exploit could allow the attacker to cause the affected device to crash and reload, resulting in a DoS condition on the affected device.

Multiple vulnerabilities in the Control and Provisioning of Wireless Access Points (CAPWAP) protocol processing of Cisco IOS XE Software for Cisco Catalyst 9800 Series Wireless Controllers could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition of an affected device. These vulnerabilities are due to insufficient validation of CAPWAP packets. An attacker could exploit these vulnerabilities by sending a malformed CAPWAP packet to an affected device. A successful exploit could allow the attacker to cause the affected device to crash and reload, resulting in a DoS condition on the affected device.

A vulnerability in the Cisco Discovery Protocol implementation for Cisco FXOS Software, Cisco IOS XR Software, and Cisco NX-OS Software could allow an unauthenticated, adjacent attacker to cause a reload of an affected device, resulting in a denial of service (DoS) condition. The vulnerability is due to a missing check when the affected software processes Cisco Discovery Protocol messages. An attacker could exploit this vulnerability by sending a malicious Cisco Discovery Protocol packet to an affected device. A successful exploit could allow the attacker to exhaust system memory, causing the device to reload. Cisco Discovery Protocol is a Layer 2 protocol. To exploit this vulnerability, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent).

Multiple vulnerabilities in the Control and Provisioning of Wireless Access Points (CAPWAP) protocol processing of Cisco IOS XE Software for Cisco Catalyst 9800 Series Wireless Controllers could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition of an affected device. These vulnerabilities are due to insufficient validation of CAPWAP packets. An attacker could exploit these vulnerabilities by sending a malformed CAPWAP packet to an affected device. A successful exploit could allow the attacker to cause the affected device to crash and reload, resulting in a DoS condition on the affected device.

The Cisco Wireless LAN Controller (WLC), Cisco Catalyst 6500 Wireless Services Module (WiSM), and Cisco Catalyst 3750 Integrated Wireless LAN Controller with software 4.x before 4.2.176.0 and 5.x before 5.2 allow remote attackers to cause a denial of service (web authentication outage or device reload) via unspecified network traffic, as demonstrated by a vulnerability scanner.

Cisco IOS XE 16.1.1 allows remote attackers to cause a denial of service (device reload) via a packet with the 00-00-00-00-00-00 source MAC address, aka Bug ID CSCux48405.