IP-in-IP protocol specifies IP Encapsulation within IP standard (RFC 2003, STD 1) that decapsulate and route IP-in-IP traffic is vulnerable to spoofing, access-control bypass and other unexpected behavior due to the lack of validation to verify network packets before decapsulation and routing.
A vulnerability in the web UI of Cisco Umbrella could allow an unauthenticated, remote attacker to negatively affect the performance of this service. The vulnerability exists due to insufficient rate limiting controls in the web UI. An attacker could exploit this vulnerability by sending crafted HTTPS packets at a high and sustained rate. A successful exploit could allow the attacker to negatively affect the performance of the web UI. Cisco has addressed this vulnerability.
A vulnerability in the DHCP version 4 (DHCPv4) server feature of Cisco IOS XR Software could allow an unauthenticated, remote attacker to trigger a crash of the dhcpd process, resulting in a denial of service (DoS) condition. This vulnerability exists because certain DHCPv4 messages are improperly validated when they are processed by an affected device. An attacker could exploit this vulnerability by sending a malformed DHCPv4 message to an affected device. A successful exploit could allow the attacker to cause a crash of the dhcpd process. While the dhcpd process is restarting, which may take approximately two minutes, DHCPv4 server services are unavailable on the affected device. This could temporarily prevent network access to clients that join the network during that time period and rely on the DHCPv4 server of the affected device. Notes: Only the dhcpd process crashes and eventually restarts automatically. The router does not reload. This vulnerability only applies to DHCPv4. DHCP version 6 (DHCPv6) is not affected.
A vulnerability in chat messaging features of Cisco Enterprise Chat and Email (ECE) could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition. This vulnerability is due to improper validation of user-supplied input to chat entry points. An attacker could exploit this vulnerability by sending malicious requests to a messaging chat entry point in the affected application. A successful exploit could allow the attacker to cause the application to stop responding, resulting in a DoS condition. The application may not recover on its own and may need an administrator to manually restart services to recover.
A vulnerability in the web UI of Cisco Desk Phone 9800 Series, Cisco IP Phone 7800 and 8800 Series, and Cisco Video Phone 8875 running Cisco SIP Software could allow an unauthenticated, remote attacker to cause a DoS condition on an affected device. This vulnerability is due to a buffer overflow when an affected device processes HTTP packets. An attacker could exploit this vulnerability by sending crafted HTTP input to the device. A successful exploit could allow the attacker to cause the device to reload, resulting in a DoS condition. Note: To exploit this vulnerability, the phone must be registered to Cisco Unified Communications Manager and have Web Access enabled. Web Access is disabled by default.
A vulnerability in the RADIUS setting Reject RADIUS requests from clients with repeated failures on Cisco Identity Services Engine (ISE) could allow an unauthenticated, remote attacker to cause Cisco ISE to restart unexpectedly. This vulnerability is due to a logic error when processing a RADIUS access request for a MAC address that is already a rejected endpoint. An attacker could exploit this vulnerability by sending a specific sequence of multiple crafted RADIUS access request messages to Cisco ISE. A successful exploit could allow the attacker to cause a denial of service (DoS) condition when Cisco ISE restarts.
A vulnerability in Universal Disk Format (UDF) processing of ClamAV could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to a memory overread during UDF file scanning. An attacker could exploit this vulnerability by submitting a crafted file containing UDF content to be scanned by ClamAV on an affected device. A successful exploit could allow the attacker to terminate the ClamAV scanning process, resulting in a DoS condition on the affected software. For a description of this vulnerability, see the .
A vulnerability in the SIP processing subsystem of Cisco BroadWorks could allow an unauthenticated, remote attacker to halt the processing of incoming SIP requests, resulting in a denial of service (DoS) condition. This vulnerability is due to improper memory handling for certain SIP requests. An attacker could exploit this vulnerability by sending a high number of SIP requests to an affected system. A successful exploit could allow the attacker to exhaust the memory that was allocated to the Cisco BroadWorks Network Servers that handle SIP traffic. If no memory is available, the Network Servers can no longer process incoming requests, resulting in a DoS condition that requires manual intervention to recover.
A vulnerability in the Cisco IOx application hosting environment of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause the Cisco IOx application hosting environment to stop responding, resulting in a denial of service (DoS) condition. This vulnerability is due to the improper handling of HTTP requests. An attacker could exploit this vulnerability by sending crafted HTTP requests to an affected device. A successful exploit could allow the attacker to cause the Cisco IOx application hosting environment to stop responding. The IOx process will need to be manually restarted to recover services.
A vulnerability in the Object Linking and Embedding 2 (OLE2) decryption routine of ClamAV could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to an integer underflow in a bounds check that allows for a heap buffer overflow read. An attacker could exploit this vulnerability by submitting a crafted file containing OLE2 content to be scanned by ClamAV on an affected device. A successful exploit could allow the attacker to terminate the ClamAV scanning process, resulting in a DoS condition on the affected software. For a description of this vulnerability, see the . Cisco has released software updates that address this vulnerability. There are no workarounds that address this vulnerability.
A vulnerability in the system resource management of Cisco Elastic Services Controller (ESC) could allow an unauthenticated, remote attacker to cause a denial of service (DoS) to the health monitor API on an affected device. The vulnerability is due to inadequate provisioning of kernel parameters for the maximum number of TCP connections and SYN backlog. An attacker could exploit this vulnerability by sending a flood of crafted TCP packets to an affected device. A successful exploit could allow the attacker to block TCP listening ports that are used by the health monitor API. This vulnerability only affects customers who use the health monitor API.
The IKEv1 implementation in Cisco IOS 12.2 through 12.4 and 15.0 through 15.2 and IOS XE 2.1.x through 2.6.x and 3.1.xS through 3.4.xS before 3.4.2S, 3.5.xS before 3.5.1S, and 3.2.xSG before 3.2.2SG allows remote attackers to cause a denial of service (device reload) by sending IKE UDP packets over (1) IPv4 or (2) IPv6, aka Bug ID CSCts38429.
A vulnerability in the Internet Key Exchange Version 2 (IKEv2) module of Cisco IOS 15.0 through 15.6 and Cisco IOS XE 3.5 through 16.5 could allow an unauthenticated, remote attacker to cause high CPU utilization, traceback messages, or a reload of an affected device that leads to a denial of service (DoS) condition. The vulnerability is due to how an affected device processes certain IKEv2 packets. An attacker could exploit this vulnerability by sending specific IKEv2 packets to an affected device to be processed. A successful exploit could allow the attacker to cause high CPU utilization, traceback messages, or a reload of the affected device that leads to a DoS condition. This vulnerability affects Cisco devices that have the Internet Security Association and Key Management Protocol (ISAKMP) enabled. Although only IKEv2 packets can be used to trigger this vulnerability, devices that are running Cisco IOS Software or Cisco IOS XE Software are vulnerable when ISAKMP is enabled. A device does not need to be configured with any IKEv2-specific features to be vulnerable. Many features use IKEv2, including different types of VPNs such as the following: LAN-to-LAN VPN; Remote-access VPN, excluding SSL VPN; Dynamic Multipoint VPN (DMVPN); and FlexVPN. Cisco Bug IDs: CSCvc41277.
A vulnerability in the implementation of the PROFINET Discovery and Configuration Protocol (PN-DCP) for Cisco IOS 12.2 through 15.6 could allow an unauthenticated, remote attacker to cause an affected device to reload, resulting in a denial of service (DoS) condition. The vulnerability is due to the improper parsing of ingress PN-DCP Identify Request packets destined to an affected device. An attacker could exploit this vulnerability by sending a crafted PN-DCP Identify Request packet to an affected device and then continuing to send normal PN-DCP Identify Request packets to the device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition. This vulnerability affects Cisco devices that are configured to process PROFINET messages. Beginning with Cisco IOS Software Release 12.2(52)SE, PROFINET is enabled by default on all the base switch module and expansion-unit Ethernet ports. Cisco Bug IDs: CSCuz47179.
Multiple vulnerabilities in the implementation of the Common Industrial Protocol (CIP) feature in Cisco IOS 12.4 through 15.6 could allow an unauthenticated, remote attacker to cause an affected device to reload, resulting in a denial of service (DoS) condition. The vulnerabilities are due to the improper parsing of crafted CIP packets destined to an affected device. An attacker could exploit these vulnerabilities by sending crafted CIP packets to be processed by an affected device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition. Cisco Bug IDs: CSCvc43709.
A memory leak vulnerability exists in Cisco IOS before 15.2(1)T due to a memory leak in the HTTP PROXY Server process (aka CSCtu52820), when configured with Cisco ISR Web Security with Cisco ScanSafe and User Authenticaiton NTLM configured.
Multiple vulnerabilities in the implementation of the Common Industrial Protocol (CIP) feature in Cisco IOS 12.4 through 15.6 could allow an unauthenticated, remote attacker to cause an affected device to reload, resulting in a denial of service (DoS) condition. The vulnerabilities are due to the improper parsing of crafted CIP packets destined to an affected device. An attacker could exploit these vulnerabilities by sending crafted CIP packets to be processed by an affected device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition. Cisco Bug IDs: CSCuz95334.
A vulnerability in the implementation of Network Address Translation (NAT) functionality in Cisco IOS 12.4 through 15.6 could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. The vulnerability is due to the improper translation of H.323 messages that use the Registration, Admission, and Status (RAS) protocol and are sent to an affected device via IPv4 packets. An attacker could exploit this vulnerability by sending a crafted H.323 RAS packet through an affected device. A successful exploit could allow the attacker to cause the affected device to crash and reload, resulting in a DoS condition. This vulnerability affects Cisco devices that are configured to use an application layer gateway with NAT (NAT ALG) for H.323 RAS messages. By default, a NAT ALG is enabled for H.323 RAS messages. Cisco Bug IDs: CSCvc57217.
The cat6000-dot1x component in Cisco IOS 12.2 before 12.2(33)SXI7 does not properly handle an external loop between a pair of dot1x enabled ports, which allows remote attackers to cause a denial of service (traffic storm) via unspecified vectors that trigger many unicast EAPoL Protocol Data Units (PDUs), aka Bug ID CSCtq36336.
The ethernet-lldp component in Cisco IOS 12.2 before 12.2(33)SXJ1 does not properly support a large number of LLDP Management Address (MA) TLVs, which allows remote attackers to cause a denial of service (device crash) via crafted LLDPDUs, aka Bug ID CSCtj22354.
A vulnerability in the AutoIt module of ClamAV could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to a logic error in the memory management of an affected device. An attacker could exploit this vulnerability by submitting a crafted AutoIt file to be scanned by ClamAV on the affected device. A successful exploit could allow the attacker to cause the ClamAV scanning process to restart unexpectedly, resulting in a DoS condition.
A vulnerability in the IPv6 DHCP version 6 (DHCPv6) relay and server features of Cisco IOS and IOS XE Software could allow an unauthenticated, remote attacker to trigger a denial of service (DoS) condition. This vulnerability is due to insufficient validation of data boundaries. An attacker could exploit this vulnerability by sending crafted DHCPv6 messages to an affected device. A successful exploit could allow the attacker to cause the device to reload unexpectedly.
Multiple vulnerabilities in the web-based management interface of certain Cisco IP Phones could allow an unauthenticated, remote attacker to execute arbitrary code or cause a denial of service (DoS) condition. For more information about these vulnerabilities, see the Details section of this advisory.
A vulnerability in a logging API in Cisco Firepower Management Center (FMC) Software could allow an unauthenticated, remote attacker to cause the device to become unresponsive or trigger an unexpected reload. This vulnerability could also allow an attacker with valid user credentials, but not Administrator privileges, to view a system log file that they would not normally have access to. This vulnerability is due to a lack of rate-limiting of requests that are sent to a specific API that is related to an FMC log. An attacker could exploit this vulnerability by sending a high rate of HTTP requests to the API. A successful exploit could allow the attacker to cause a denial of service (DoS) condition due to the FMC CPU spiking to 100 percent utilization or to the device reloading. CPU utilization would return to normal if the attack traffic was stopped before an unexpected reload was triggered.
A vulnerability in the bidirectional forwarding detection (BFD) hardware offload feature of Cisco IOS XR Software for Cisco ASR 9000 Series Aggregation Services Routers, ASR 9902 Compact High-Performance Routers, and ASR 9903 Compact High-Performance Routers could allow an unauthenticated, remote attacker to cause a line card to reset, resulting in a denial of service (DoS) condition. This vulnerability is due to the incorrect handling of malformed BFD packets that are received on line cards where the BFD hardware offload feature is enabled. An attacker could exploit this vulnerability by sending a crafted IPv4 BFD packet to an affected device. A successful exploit could allow the attacker to cause line card exceptions or a hard reset, resulting in loss of traffic over that line card while the line card reloads.
A vulnerability in an API of the Web Bridge feature of Cisco Meeting Server could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition. This vulnerability is due to insufficient validation of HTTP requests. An attacker could exploit this vulnerability by sending crafted HTTP packets to an affected device. A successful exploit could allow the attacker to cause a partial availability condition, which could cause ongoing video calls to be dropped due to the invalid packets reaching the Web Bridge.
A vulnerability in the Vector Packet Processor (VPP) of Cisco Packet Data Network Gateway (PGW) could allow an unauthenticated, remote attacker to stop ICMP traffic from being processed over an IPsec connection. This vulnerability is due to the VPP improperly handling a malformed packet. An attacker could exploit this vulnerability by sending a malformed Encapsulating Security Payload (ESP) packet over an IPsec connection. A successful exploit could allow the attacker to stop ICMP traffic over an IPsec connection and cause a denial of service (DoS).
A vulnerability in the Multicast Leaf Recycle Elimination (mLRE) feature of Cisco IOS XE Software for Cisco ASR 1000 Series Aggregation Services Routers could allow an unauthenticated, remote attacker to cause the affected device to reload, resulting in a denial of service (DoS) condition. This vulnerability is due to incorrect handling of certain IPv6 multicast packets when they are fanned out more than seven times on an affected device. An attacker could exploit this vulnerability by sending a specific IPv6 multicast or IPv6 multicast VPN (MVPNv6) packet through the affected device. A successful exploit could allow the attacker to cause a reload of the affected device, resulting in a DoS condition.
Multiple vulnerabilities in the web-based user interface of certain Cisco Small Business Series Switches could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition or execute arbitrary code with root privileges on an affected device. These vulnerabilities are due to improper validation of requests that are sent to the web interface. For more information about these vulnerabilities, see the Details section of this advisory.
A vulnerability in the filesystem image parser for Hierarchical File System Plus (HFS+) of ClamAV could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to an incorrect check for completion when a file is decompressed, which may result in a loop condition that could cause the affected software to stop responding. An attacker could exploit this vulnerability by submitting a crafted HFS+ filesystem image to be scanned by ClamAV on an affected device. A successful exploit could allow the attacker to cause the ClamAV scanning process to stop responding, resulting in a DoS condition on the affected software and consuming available system resources. For a description of this vulnerability, see the ClamAV blog .
A vulnerability in an API endpoint of multiple Cisco Unified Communications Products could allow an unauthenticated, remote attacker to cause high CPU utilization, which could impact access to the web-based management interface and cause delays with call processing. This API is not used for device management and is unlikely to be used in normal operations of the device. This vulnerability is due to improper API authentication and incomplete validation of the API request. An attacker could exploit this vulnerability by sending a crafted HTTP request to a specific API on the device. A successful exploit could allow the attacker to cause a denial of service (DoS) condition due to high CPU utilization, which could negatively impact user traffic and management access. When the attack stops, the device will recover without manual intervention.
A vulnerability in the SSH service of Cisco Catalyst SD-WAN Manager could allow an unauthenticated, remote attacker to cause a process crash, resulting in a DoS condition for SSH access only. This vulnerability does not prevent the system from continuing to function, and web UI access is not affected. This vulnerability is due to insufficient resource management when an affected system is in an error condition. An attacker could exploit this vulnerability by sending malicious traffic to the affected system. A successful exploit could allow the attacker to cause the SSH process to crash and restart, resulting in a DoS condition for the SSH service.
A vulnerability in Application Quality of Experience (AppQoE) and Unified Threat Defense (UTD) on Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause an affected device to reload unexpectedly, resulting in a denial of service (DoS) condition. This vulnerability is due to the mishandling of a crafted packet stream through the AppQoE or UTD application. An attacker could exploit this vulnerability by sending a crafted packet stream through an affected device. A successful exploit could allow the attacker to cause the device to reload, resulting in a DoS condition.
A vulnerability in the XCP Authentication Service of the Cisco Unified Communications Manager IM & Presence Service (Unified CM IM&P) could allow an unauthenticated, remote attacker to cause a temporary service outage for all Cisco Unified CM IM&P users who are attempting to authenticate to the service, resulting in a denial of service (DoS) condition. This vulnerability is due to improper validation of user-supplied input. An attacker could exploit this vulnerability by sending a crafted login message to the affected device. A successful exploit could allow the attacker to cause an unexpected restart of the authentication service, preventing new users from successfully authenticating. Exploitation of this vulnerability does not impact Cisco Unified CM IM&P users who were authenticated prior to an attack.
A vulnerability in the hardware-based SSL/TLS cryptography functionality of Cisco Adaptive Security Appliance (ASA) Software and Cisco Firepower Threat Defense (FTD) Software for Cisco Firepower 2100 Series Appliances could allow an unauthenticated, remote attacker to cause an affected device to reload unexpectedly, resulting in a denial of service (DoS) condition. This vulnerability is due to an implementation error within the cryptographic functions for SSL/TLS traffic processing when they are offloaded to the hardware. An attacker could exploit this vulnerability by sending a crafted stream of SSL/TLS traffic to an affected device. A successful exploit could allow the attacker to cause an unexpected error in the hardware-based cryptography engine, which could cause the device to reload.
The AAA service in Cisco IOS 12.0 through 12.4 and 15.0 through 15.6 and IOS XE 2.1 through 3.18 and 16.2 allows remote attackers to cause a denial of service (device reload) via a failed SSH connection attempt that is mishandled during generation of an error-log message, aka Bug ID CSCuy87667.
Cisco ACE A2(3.6) allows log retention DoS.
A vulnerability in the web-based management interface of Cisco Small Business 200 Series Smart Switches, Cisco Small Business 300 Series Managed Switches, and Cisco Small Business 500 Series Stackable Managed Switches could allow an unauthenticated, remote attacker to render the web-based management interface unusable, resulting in a denial of service (DoS) condition. This vulnerability is due to improper validation of HTTP requests. An attacker could exploit this vulnerability by sending a crafted HTTP request to an affected device. A successful exploit could allow the attacker to cause a permanent invalid redirect for requests sent to the web-based management interface of the device, resulting in a DoS condition.
A vulnerability in an API of the Call Bridge feature of Cisco Meeting Server could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition. This vulnerability is due to improper handling of large series of message requests. An attacker could exploit this vulnerability by sending a series of messages to the vulnerable API. A successful exploit could allow the attacker to cause the affected device to reload, dropping all ongoing calls and resulting in a DoS condition.
A vulnerability in SSL/TLS message handler for Cisco Adaptive Security Appliance (ASA) Software and Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability exists because incoming SSL/TLS packets are not properly processed. An attacker could exploit this vulnerability by sending a crafted SSL/TLS packet to an affected device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition.
A vulnerability in the web services interface of Cisco Adaptive Security Appliance (ASA) Software and Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to trigger a denial of service (DoS) condition. This vulnerability is due to improper input validation when parsing HTTPS requests. An attacker could exploit this vulnerability by sending a malicious HTTPS request to an affected device. A successful exploit could allow the attacker to cause the device to reload, resulting in a DoS condition.
Cisco IOS XR 3.4.0 through 3.9.1, when BGP is enabled, does not properly handle unrecognized transitive attributes, which allows remote attackers to cause a denial of service (peering reset) via a crafted prefix announcement, as demonstrated in the wild in August 2010 with attribute type code 99, aka Bug ID CSCti62211.
Multiple Cisco products are affected by a vulnerability in Snort rules that could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device.The vulnerability is due to improper handling of the Block with Reset or Interactive Block with Reset actions if a rule is configured without proper constraints. An attacker could exploit this vulnerability by sending a crafted IP packet to the affected device. A successful exploit could allow the attacker to cause through traffic to be dropped. Note: Only products with Snort3 configured and either a rule with Block with Reset or Interactive Block with Reset actions configured are vulnerable. Products configured with Snort2 are not vulnerable.
Multiple Cisco products are affected by a vulnerability in the way the Snort detection engine processes ICMP traffic that could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. The vulnerability is due to improper memory resource management while the Snort detection engine is processing ICMP packets. An attacker could exploit this vulnerability by sending a series of ICMP packets through an affected device. A successful exploit could allow the attacker to exhaust resources on the affected device, causing the device to reload.
Multiple vulnerabilities in the Control and Provisioning of Wireless Access Points (CAPWAP) protocol processing of Cisco IOS XE Software for Cisco Catalyst 9000 Family Wireless Controllers could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. These vulnerabilities are due to insufficient validation of CAPWAP packets. An attacker could exploit the vulnerabilities by sending a malformed CAPWAP packet to an affected device. A successful exploit could allow the attacker to cause the affected device to crash and reload, resulting in a DoS condition.
The Multicast Source Discovery Protocol (MSDP) implementation in Cisco IOS 12.0, 12.2 through 12.4, and 15.0 through 15.2 and IOS XE 2.1.x through 2.6.x and 3.1.xS through 3.4.xS before 3.4.1S and 3.1.xSG and 3.2.xSG before 3.2.2SG allows remote attackers to cause a denial of service (device reload) via encapsulated IGMP data in an MSDP packet, aka Bug ID CSCtr28857.
Multiple vulnerabilities in the Control and Provisioning of Wireless Access Points (CAPWAP) protocol processing of Cisco IOS XE Software for Cisco Catalyst 9000 Family Wireless Controllers could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. These vulnerabilities are due to insufficient validation of CAPWAP packets. An attacker could exploit the vulnerabilities by sending a malformed CAPWAP packet to an affected device. A successful exploit could allow the attacker to cause the affected device to crash and reload, resulting in a DoS condition.
Multiple vulnerabilities in the Cisco ATA 190 Series Analog Telephone Adapter Software could allow an attacker to perform a command injection attack resulting in remote code execution or cause a denial of service (DoS) condition on an affected device. For more information about these vulnerabilities, see the Details section of this advisory.
A vulnerability in the nginx configurations that are provided as part of the VPN-less reverse proxy for Cisco Finesse could allow an unauthenticated, remote attacker to create a denial of service (DoS) condition for new and existing users who are connected through a load balancer. This vulnerability is due to improper IP address filtering by the reverse proxy. An attacker could exploit this vulnerability by sending a series of unauthenticated requests to the reverse proxy. A successful exploit could allow the attacker to cause all current traffic and subsequent requests to the reverse proxy through a load balancer to be dropped, resulting in a DoS condition.
A vulnerability in the email scanning algorithm of Cisco AsyncOS software for Cisco Email Security Appliance (ESA) could allow an unauthenticated, remote attacker to perform a denial of service (DoS) attack against an affected device. This vulnerability is due to insufficient input validation of incoming emails. An attacker could exploit this vulnerability by sending a crafted email through Cisco ESA. A successful exploit could allow the attacker to exhaust all the available CPU resources on an affected device for an extended period of time, preventing other emails from being processed and resulting in a DoS condition.