In the Linux kernel, the following vulnerability has been resolved: powerpc/pseries/iommu: LPAR panics during boot up with a frozen PE At the time of LPAR boot up, partition firmware provides Open Firmware property ibm,dma-window for the PE. This property is provided on the PCI bus the PE is attached to. There are execptions where the partition firmware might not provide this property for the PE at the time of LPAR boot up. One of the scenario is where the firmware has frozen the PE due to some error condition. This PE is frozen for 24 hours or unless the whole system is reinitialized. Within this time frame, if the LPAR is booted, the frozen PE will be presented to the LPAR but ibm,dma-window property could be missing. Today, under these circumstances, the LPAR oopses with NULL pointer dereference, when configuring the PCI bus the PE is attached to. BUG: Kernel NULL pointer dereference on read at 0x000000c8 Faulting instruction address: 0xc0000000001024c0 Oops: Kernel access of bad area, sig: 7 [#1] LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries Modules linked in: Supported: Yes CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.4.0-150600.9-default #1 Hardware name: IBM,9043-MRX POWER10 (raw) 0x800200 0xf000006 of:IBM,FW1060.00 (NM1060_023) hv:phyp pSeries NIP: c0000000001024c0 LR: c0000000001024b0 CTR: c000000000102450 REGS: c0000000037db5c0 TRAP: 0300 Not tainted (6.4.0-150600.9-default) MSR: 8000000002009033 <SF,VEC,EE,ME,IR,DR,RI,LE> CR: 28000822 XER: 00000000 CFAR: c00000000010254c DAR: 00000000000000c8 DSISR: 00080000 IRQMASK: 0 ... NIP [c0000000001024c0] pci_dma_bus_setup_pSeriesLP+0x70/0x2a0 LR [c0000000001024b0] pci_dma_bus_setup_pSeriesLP+0x60/0x2a0 Call Trace: pci_dma_bus_setup_pSeriesLP+0x60/0x2a0 (unreliable) pcibios_setup_bus_self+0x1c0/0x370 __of_scan_bus+0x2f8/0x330 pcibios_scan_phb+0x280/0x3d0 pcibios_init+0x88/0x12c do_one_initcall+0x60/0x320 kernel_init_freeable+0x344/0x3e4 kernel_init+0x34/0x1d0 ret_from_kernel_user_thread+0x14/0x1c

In the Linux kernel before 5.16.3, drivers/bluetooth/hci_qca.c misinterprets the devm_gpiod_get_index_optional return value (expects it to be NULL in the error case, whereas it is actually an error pointer).

The udp_sendmsg function in the UDP implementation in (1) net/ipv4/udp.c and (2) net/ipv6/udp.c in the Linux kernel before 2.6.19 allows local users to gain privileges or cause a denial of service (NULL pointer dereference and system crash) via vectors involving the MSG_MORE flag and a UDP socket.

In the Linux kernel before 5.15.13, drivers/net/ethernet/mellanox/mlx5/core/steering/dr_domain.c misinterprets the mlx5_get_uars_page return value (expects it to be NULL in the error case, whereas it is actually an error pointer).

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Properly link new fs rules into the tree Previously, add_rule_fg would only add newly created rules from the handle into the tree when they had a refcount of 1. On the other hand, create_flow_handle tries hard to find and reference already existing identical rules instead of creating new ones. These two behaviors can result in a situation where create_flow_handle 1) creates a new rule and references it, then 2) in a subsequent step during the same handle creation references it again, resulting in a rule with a refcount of 2 that is not linked into the tree, will have a NULL parent and root and will result in a crash when the flow group is deleted because del_sw_hw_rule, invoked on rule deletion, assumes node->parent is != NULL. This happened in the wild, due to another bug related to incorrect handling of duplicate pkt_reformat ids, which lead to the code in create_flow_handle incorrectly referencing a just-added rule in the same flow handle, resulting in the problem described above. Full details are at [1]. This patch changes add_rule_fg to add new rules without parents into the tree, properly initializing them and avoiding the crash. This makes it more consistent with how rules are added to an FTE in create_flow_handle.

In the Linux kernel, the following vulnerability has been resolved: tracing/osnoise: Use a cpumask to know what threads are kthreads The start_kthread() and stop_thread() code was not always called with the interface_lock held. This means that the kthread variable could be unexpectedly changed causing the kthread_stop() to be called on it when it should not have been, leading to: while true; do rtla timerlat top -u -q & PID=$!; sleep 5; kill -INT $PID; sleep 0.001; kill -TERM $PID; wait $PID; done Causing the following OOPS: Oops: general protection fault, probably for non-canonical address 0xdffffc0000000002: 0000 [#1] PREEMPT SMP KASAN PTI KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017] CPU: 5 UID: 0 PID: 885 Comm: timerlatu/5 Not tainted 6.11.0-rc4-test-00002-gbc754cc76d1b-dirty #125 a533010b71dab205ad2f507188ce8c82203b0254 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 RIP: 0010:hrtimer_active+0x58/0x300 Code: 48 c1 ee 03 41 54 48 01 d1 48 01 d6 55 53 48 83 ec 20 80 39 00 0f 85 30 02 00 00 49 8b 6f 30 4c 8d 75 10 4c 89 f0 48 c1 e8 03 <0f> b6 3c 10 4c 89 f0 83 e0 07 83 c0 03 40 38 f8 7c 09 40 84 ff 0f RSP: 0018:ffff88811d97f940 EFLAGS: 00010202 RAX: 0000000000000002 RBX: ffff88823c6b5b28 RCX: ffffed10478d6b6b RDX: dffffc0000000000 RSI: ffffed10478d6b6c RDI: ffff88823c6b5b28 RBP: 0000000000000000 R08: ffff88823c6b5b58 R09: ffff88823c6b5b60 R10: ffff88811d97f957 R11: 0000000000000010 R12: 00000000000a801d R13: ffff88810d8b35d8 R14: 0000000000000010 R15: ffff88823c6b5b28 FS: 0000000000000000(0000) GS:ffff88823c680000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000561858ad7258 CR3: 000000007729e001 CR4: 0000000000170ef0 Call Trace: <TASK> ? die_addr+0x40/0xa0 ? exc_general_protection+0x154/0x230 ? asm_exc_general_protection+0x26/0x30 ? hrtimer_active+0x58/0x300 ? __pfx_mutex_lock+0x10/0x10 ? __pfx_locks_remove_file+0x10/0x10 hrtimer_cancel+0x15/0x40 timerlat_fd_release+0x8e/0x1f0 ? security_file_release+0x43/0x80 __fput+0x372/0xb10 task_work_run+0x11e/0x1f0 ? _raw_spin_lock+0x85/0xe0 ? __pfx_task_work_run+0x10/0x10 ? poison_slab_object+0x109/0x170 ? do_exit+0x7a0/0x24b0 do_exit+0x7bd/0x24b0 ? __pfx_migrate_enable+0x10/0x10 ? __pfx_do_exit+0x10/0x10 ? __pfx_read_tsc+0x10/0x10 ? ktime_get+0x64/0x140 ? _raw_spin_lock_irq+0x86/0xe0 do_group_exit+0xb0/0x220 get_signal+0x17ba/0x1b50 ? vfs_read+0x179/0xa40 ? timerlat_fd_read+0x30b/0x9d0 ? __pfx_get_signal+0x10/0x10 ? __pfx_timerlat_fd_read+0x10/0x10 arch_do_signal_or_restart+0x8c/0x570 ? __pfx_arch_do_signal_or_restart+0x10/0x10 ? vfs_read+0x179/0xa40 ? ksys_read+0xfe/0x1d0 ? __pfx_ksys_read+0x10/0x10 syscall_exit_to_user_mode+0xbc/0x130 do_syscall_64+0x74/0x110 ? __pfx___rseq_handle_notify_resume+0x10/0x10 ? __pfx_ksys_read+0x10/0x10 ? fpregs_restore_userregs+0xdb/0x1e0 ? fpregs_restore_userregs+0xdb/0x1e0 ? syscall_exit_to_user_mode+0x116/0x130 ? do_syscall_64+0x74/0x110 ? do_syscall_64+0x74/0x110 ? do_syscall_64+0x74/0x110 entry_SYSCALL_64_after_hwframe+0x71/0x79 RIP: 0033:0x7ff0070eca9c Code: Unable to access opcode bytes at 0x7ff0070eca72. RSP: 002b:00007ff006dff8c0 EFLAGS: 00000246 ORIG_RAX: 0000000000000000 RAX: 0000000000000000 RBX: 0000000000000005 RCX: 00007ff0070eca9c RDX: 0000000000000400 RSI: 00007ff006dff9a0 RDI: 0000000000000003 RBP: 00007ff006dffde0 R08: 0000000000000000 R09: 00007ff000000ba0 R10: 00007ff007004b08 R11: 0000000000000246 R12: 0000000000000003 R13: 00007ff006dff9a0 R14: 0000000000000007 R15: 0000000000000008 </TASK> Modules linked in: snd_hda_intel snd_intel_dspcfg snd_intel_sdw_acpi snd_hda_codec snd_hwdep snd_hda_core ---[ end trace 0000000000000000 ]--- This is because it would mistakenly call kthread_stop() on a user space thread making it "exit" before it actually exits. Since kthread ---truncated---

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: qca: fix NULL-deref on non-serdev suspend Qualcomm ROME controllers can be registered from the Bluetooth line discipline and in this case the HCI UART serdev pointer is NULL. Add the missing sanity check to prevent a NULL-pointer dereference when wakeup() is called for a non-serdev controller during suspend. Just return true for now to restore the original behaviour and address the crash with pre-6.2 kernels, which do not have commit e9b3e5b8c657 ("Bluetooth: hci_qca: only assign wakeup with serial port support") that causes the crash to happen already at setup() time.

In the Linux kernel before 5.19, drivers/gpu/drm/arm/malidp_planes.c misinterprets the get_sg_table return value (expects it to be NULL in the error case, whereas it is actually an error pointer).

In the Linux kernel before 6.1.2, kernel/module/decompress.c misinterprets the module_get_next_page return value (expects it to be NULL in the error case, whereas it is actually an error pointer).

In the Linux kernel before 5.17, drivers/phy/tegra/xusb.c mishandles the tegra_xusb_find_port_node return value. Callers expect NULL in the error case, but an error pointer is used.

The load_flat_shared_library function in fs/binfmt_flat.c in the flat subsystem in the Linux kernel before 2.6.31-rc6 allows local users to cause a denial of service (NULL pointer dereference and system crash) or possibly have unspecified other impact by executing a shared flat binary, which triggers an access of an "uninitialized cred pointer."

The ATI Rage 128 (aka r128) driver in the Linux kernel before 2.6.31-git11 does not properly verify Concurrent Command Engine (CCE) state initialization, which allows local users to cause a denial of service (NULL pointer dereference and system crash) or possibly gain privileges via unspecified ioctl calls.

In the Linux kernel, the following vulnerability has been resolved: mm: zswap: fix shrinker NULL crash with cgroup_disable=memory Christian reports a NULL deref in zswap that he bisected down to the zswap shrinker. The issue also cropped up in the bug trackers of libguestfs [1] and the Red Hat bugzilla [2]. The problem is that when memcg is disabled with the boot time flag, the zswap shrinker might get called with sc->memcg == NULL. This is okay in many places, like the lruvec operations. But it crashes in memcg_page_state() - which is only used due to the non-node accounting of cgroup's the zswap memory to begin with. Nhat spotted that the memcg can be NULL in the memcg-disabled case, and I was then able to reproduce the crash locally as well. [1] https://github.com/libguestfs/libguestfs/issues/139 [2] https://bugzilla.redhat.com/show_bug.cgi?id=2275252

In the Linux kernel, the following vulnerability has been resolved: media: mediatek: vcodec: adding lock to protect encoder context list Add a lock for the ctx_list, to avoid accessing a NULL pointer within the 'vpu_enc_ipi_handler' function when the ctx_list has been deleted due to an unexpected behavior on the SCP IP block.

In the Linux kernel, the following vulnerability has been resolved: net: phy: micrel: Fix potential null pointer dereference In lan8814_get_sig_rx() and lan8814_get_sig_tx() ptp_parse_header() may return NULL as ptp_header due to abnormal packet type or corrupted packet. Fix this bug by adding ptp_header check. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: PCI: of_property: Return error for int_map allocation failure Return -ENOMEM from of_pci_prop_intr_map() if kcalloc() fails to prevent a NULL pointer dereference in this case. [bhelgaas: commit log]

A null pointer dereference issue was found in the sctp network protocol in net/sctp/stream_sched.c in Linux Kernel. If stream_in allocation is failed, stream_out is freed which would further be accessed. A local user could use this flaw to crash the system or potentially cause a denial of service.

In the Linux kernel, the following vulnerability has been resolved: scsi: target: Fix WRITE_SAME No Data Buffer crash In newer version of the SBC specs, we have a NDOB bit that indicates there is no data buffer that gets written out. If this bit is set using commands like "sg_write_same --ndob" we will crash in target_core_iblock/file's execute_write_same handlers when we go to access the se_cmd->t_data_sg because its NULL. This patch adds a check for the NDOB bit in the common WRITE SAME code because we don't support it. And, it adds a check for zero SG elements in each handler in case the initiator tries to send a normal WRITE SAME with no data buffer.

The kvm_arch_vcpu_ioctl_set_sregs function in the KVM in Linux kernel 2.6 before 2.6.30, when running on x86 systems, does not validate the page table root in a KVM_SET_SREGS call, which allows local users to cause a denial of service (crash or hang) via a crafted cr3 value, which triggers a NULL pointer dereference in the gfn_to_rmap function.

A null pointer dereference issue was found in can protocol in net/can/af_can.c in the Linux before Linux. ml_priv may not be initialized in the receive path of CAN frames. A local user could use this flaw to crash the system or potentially cause a denial of service.

A NULL pointer dereference was found in io_file_bitmap_get in io_uring/filetable.c in the io_uring sub-component in the Linux Kernel. When fixed files are unregistered, some context information (file_alloc_{start,end} and alloc_hint) is not cleared. A subsequent request that has auto index selection enabled via IORING_FILE_INDEX_ALLOC can cause a NULL pointer dereference. An unprivileged user can use the flaw to cause a system crash.

In the Linux kernel, the following vulnerability has been resolved: rose: Fix NULL pointer dereference in rose_send_frame() The syzkaller reported an issue: KASAN: null-ptr-deref in range [0x0000000000000380-0x0000000000000387] CPU: 0 PID: 4069 Comm: kworker/0:15 Not tainted 6.0.0-syzkaller-02734-g0326074ff465 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/22/2022 Workqueue: rcu_gp srcu_invoke_callbacks RIP: 0010:rose_send_frame+0x1dd/0x2f0 net/rose/rose_link.c:101 Call Trace: <IRQ> rose_transmit_clear_request+0x1d5/0x290 net/rose/rose_link.c:255 rose_rx_call_request+0x4c0/0x1bc0 net/rose/af_rose.c:1009 rose_loopback_timer+0x19e/0x590 net/rose/rose_loopback.c:111 call_timer_fn+0x1a0/0x6b0 kernel/time/timer.c:1474 expire_timers kernel/time/timer.c:1519 [inline] __run_timers.part.0+0x674/0xa80 kernel/time/timer.c:1790 __run_timers kernel/time/timer.c:1768 [inline] run_timer_softirq+0xb3/0x1d0 kernel/time/timer.c:1803 __do_softirq+0x1d0/0x9c8 kernel/softirq.c:571 [...] </IRQ> It triggers NULL pointer dereference when 'neigh->dev->dev_addr' is called in the rose_send_frame(). It's the first occurrence of the `neigh` is in rose_loopback_timer() as `rose_loopback_neigh', and the 'dev' in 'rose_loopback_neigh' is initialized sa nullptr. It had been fixed by commit 3b3fd068c56e3fbea30090859216a368398e39bf ("rose: Fix Null pointer dereference in rose_send_frame()") ever. But it's introduced by commit 3c53cd65dece47dd1f9d3a809f32e59d1d87b2b8 ("rose: check NULL rose_loopback_neigh->loopback") again. We fix it by add NULL check in rose_transmit_clear_request(). When the 'dev' in 'neigh' is NULL, we don't reply the request and just clear it. syzkaller don't provide repro, and I provide a syz repro like: r0 = syz_init_net_socket$bt_sco(0x1f, 0x5, 0x2) ioctl$sock_inet_SIOCSIFFLAGS(r0, 0x8914, &(0x7f0000000180)={'rose0\x00', 0x201}) r1 = syz_init_net_socket$rose(0xb, 0x5, 0x0) bind$rose(r1, &(0x7f00000000c0)=@full={0xb, @dev, @null, 0x0, [@null, @null, @netrom, @netrom, @default, @null]}, 0x40) connect$rose(r1, &(0x7f0000000240)=@short={0xb, @dev={0xbb, 0xbb, 0xbb, 0x1, 0x0}, @remote={0xcc, 0xcc, 0xcc, 0xcc, 0xcc, 0xcc, 0x1}, 0x1, @netrom={0xbb, 0xbb, 0xbb, 0xbb, 0xbb, 0x0, 0x0}}, 0x1c)

NVIDIA CUDA Toolkit SDK contains a bug in cuobjdump, where a local user running the tool against an ill-formed binary may cause a null- pointer dereference, which may result in a limited denial of service.

In the Linux kernel, the following vulnerability has been resolved: IB/hfi1: Correctly move list in sc_disable() Commit 13bac861952a ("IB/hfi1: Fix abba locking issue with sc_disable()") incorrectly tries to move a list from one list head to another. The result is a kernel crash. The crash is triggered when a link goes down and there are waiters for a send to complete. The following signature is seen: BUG: kernel NULL pointer dereference, address: 0000000000000030 [...] Call Trace: sc_disable+0x1ba/0x240 [hfi1] pio_freeze+0x3d/0x60 [hfi1] handle_freeze+0x27/0x1b0 [hfi1] process_one_work+0x1b0/0x380 ? process_one_work+0x380/0x380 worker_thread+0x30/0x360 ? process_one_work+0x380/0x380 kthread+0xd7/0x100 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork+0x1f/0x30 The fix is to use the correct call to move the list.

In the Linux kernel, the following vulnerability has been resolved: net, neigh: Fix null-ptr-deref in neigh_table_clear() When IPv6 module gets initialized but hits an error in the middle, kenel panic with: KASAN: null-ptr-deref in range [0x0000000000000598-0x000000000000059f] CPU: 1 PID: 361 Comm: insmod Hardware name: QEMU Standard PC (i440FX + PIIX, 1996) RIP: 0010:__neigh_ifdown.isra.0+0x24b/0x370 RSP: 0018:ffff888012677908 EFLAGS: 00000202 ... Call Trace: <TASK> neigh_table_clear+0x94/0x2d0 ndisc_cleanup+0x27/0x40 [ipv6] inet6_init+0x21c/0x2cb [ipv6] do_one_initcall+0xd3/0x4d0 do_init_module+0x1ae/0x670 ... Kernel panic - not syncing: Fatal exception When ipv6 initialization fails, it will try to cleanup and calls: neigh_table_clear() neigh_ifdown(tbl, NULL) pneigh_queue_purge(&tbl->proxy_queue, dev_net(dev == NULL)) # dev_net(NULL) triggers null-ptr-deref. Fix it by passing NULL to pneigh_queue_purge() in neigh_ifdown() if dev is NULL, to make kernel not panic immediately.

A NULL pointer dereference vulnerability in the Linux kernel NVMe functionality, in nvmet_setup_auth(), allows an attacker to perform a Pre-Auth Denial of Service (DoS) attack on a remote machine. Affected versions v6.0-rc1 to v6.0-rc3, fixed in v6.0-rc4.

In the Linux kernel, the following vulnerability has been resolved: SUNRPC: Fix null-ptr-deref when xps sysfs alloc failed There is a null-ptr-deref when xps sysfs alloc failed: BUG: KASAN: null-ptr-deref in sysfs_do_create_link_sd+0x40/0xd0 Read of size 8 at addr 0000000000000030 by task gssproxy/457 CPU: 5 PID: 457 Comm: gssproxy Not tainted 6.0.0-09040-g02357b27ee03 #9 Call Trace: <TASK> dump_stack_lvl+0x34/0x44 kasan_report+0xa3/0x120 sysfs_do_create_link_sd+0x40/0xd0 rpc_sysfs_client_setup+0x161/0x1b0 rpc_new_client+0x3fc/0x6e0 rpc_create_xprt+0x71/0x220 rpc_create+0x1d4/0x350 gssp_rpc_create+0xc3/0x160 set_gssp_clnt+0xbc/0x140 write_gssp+0x116/0x1a0 proc_reg_write+0xd6/0x130 vfs_write+0x177/0x690 ksys_write+0xb9/0x150 do_syscall_64+0x35/0x80 entry_SYSCALL_64_after_hwframe+0x46/0xb0 When the xprt_switch sysfs alloc failed, should not add xprt and switch sysfs to it, otherwise, maybe null-ptr-deref; also initialize the 'xps_sysfs' to NULL to avoid oops when destroy it.

In the Linux kernel, the following vulnerability has been resolved: net: phy: at803x: fix NULL pointer dereference on AR9331 PHY Latest kernel will explode on the PHY interrupt config, since it depends now on allocated priv. So, run probe to allocate priv to fix it. ar9331_switch ethernet.1:10 lan0 (uninitialized): PHY [!ahb!ethernet@1a000000!mdio!switch@10:00] driver [Qualcomm Atheros AR9331 built-in PHY] (irq=13) CPU 0 Unable to handle kernel paging request at virtual address 0000000a, epc == 8050e8a8, ra == 80504b34 ... Call Trace: [<8050e8a8>] at803x_config_intr+0x5c/0xd0 [<80504b34>] phy_request_interrupt+0xa8/0xd0 [<8050289c>] phylink_bringup_phy+0x2d8/0x3ac [<80502b68>] phylink_fwnode_phy_connect+0x118/0x130 [<8074d8ec>] dsa_slave_create+0x270/0x420 [<80743b04>] dsa_port_setup+0x12c/0x148 [<8074580c>] dsa_register_switch+0xaf0/0xcc0 [<80511344>] ar9331_sw_probe+0x370/0x388 [<8050cb78>] mdio_probe+0x44/0x70 [<804df300>] really_probe+0x200/0x424 [<804df7b4>] __driver_probe_device+0x290/0x298 [<804df810>] driver_probe_device+0x54/0xe4 [<804dfd50>] __device_attach_driver+0xe4/0x130 [<804dcb00>] bus_for_each_drv+0xb4/0xd8 [<804dfac4>] __device_attach+0x104/0x1a4 [<804ddd24>] bus_probe_device+0x48/0xc4 [<804deb44>] deferred_probe_work_func+0xf0/0x10c [<800a0ffc>] process_one_work+0x314/0x4d4 [<800a17fc>] worker_thread+0x2a4/0x354 [<800a9a54>] kthread+0x134/0x13c [<8006306c>] ret_from_kernel_thread+0x14/0x1c Same Issue would affect some other PHYs (QCA8081, QCA9561), so fix it too.

In the Linux kernel, the following vulnerability has been resolved: scsi: ibmvfc: Store vhost pointer during subcrq allocation Currently the back pointer from a queue to the vhost adapter isn't set until after subcrq interrupt registration. The value is available when a queue is first allocated and can/should be also set for primary and async queues as well as subcrqs. This fixes a crash observed during kexec/kdump on Power 9 with legacy XICS interrupt controller where a pending subcrq interrupt from the previous kernel can be replayed immediately upon IRQ registration resulting in dereference of a garbage backpointer in ibmvfc_interrupt_scsi(). Kernel attempted to read user page (58) - exploit attempt? (uid: 0) BUG: Kernel NULL pointer dereference on read at 0x00000058 Faulting instruction address: 0xc008000003216a08 Oops: Kernel access of bad area, sig: 11 [#1] ... NIP [c008000003216a08] ibmvfc_interrupt_scsi+0x40/0xb0 [ibmvfc] LR [c0000000082079e8] __handle_irq_event_percpu+0x98/0x270 Call Trace: [c000000047fa3d80] [c0000000123e6180] 0xc0000000123e6180 (unreliable) [c000000047fa3df0] [c0000000082079e8] __handle_irq_event_percpu+0x98/0x270 [c000000047fa3ea0] [c000000008207d18] handle_irq_event+0x98/0x188 [c000000047fa3ef0] [c00000000820f564] handle_fasteoi_irq+0xc4/0x310 [c000000047fa3f40] [c000000008205c60] generic_handle_irq+0x50/0x80 [c000000047fa3f60] [c000000008015c40] __do_irq+0x70/0x1a0 [c000000047fa3f90] [c000000008016d7c] __do_IRQ+0x9c/0x130 [c000000014622f60] [0000000020000000] 0x20000000 [c000000014622ff0] [c000000008016e50] do_IRQ+0x40/0xa0 [c000000014623020] [c000000008017044] replay_soft_interrupts+0x194/0x2f0 [c000000014623210] [c0000000080172a8] arch_local_irq_restore+0x108/0x170 [c000000014623240] [c000000008eb1008] _raw_spin_unlock_irqrestore+0x58/0xb0 [c000000014623270] [c00000000820b12c] __setup_irq+0x49c/0x9f0 [c000000014623310] [c00000000820b7c0] request_threaded_irq+0x140/0x230 [c000000014623380] [c008000003212a50] ibmvfc_register_scsi_channel+0x1e8/0x2f0 [ibmvfc] [c000000014623450] [c008000003213d1c] ibmvfc_init_sub_crqs+0xc4/0x1f0 [ibmvfc] [c0000000146234d0] [c0080000032145a8] ibmvfc_reset_crq+0x150/0x210 [ibmvfc] [c000000014623550] [c0080000032147c8] ibmvfc_init_crq+0x160/0x280 [ibmvfc] [c0000000146235f0] [c00800000321a9cc] ibmvfc_probe+0x2a4/0x530 [ibmvfc]

In the Linux kernel, the following vulnerability has been resolved: bpftool: Fix NULL pointer dereference when pin {PROG, MAP, LINK} without FILE When using bpftool to pin {PROG, MAP, LINK} without FILE, segmentation fault will occur. The reson is that the lack of FILE will cause strlen to trigger NULL pointer dereference. The corresponding stacktrace is shown below: do_pin do_pin_any do_pin_fd mount_bpffs_for_pin strlen(name) <- NULL pointer dereference Fix it by adding validation to the common process.

In the Linux kernel, the following vulnerability has been resolved: drm/amdkfd: Fix NULL pointer dereference in svm_migrate_to_ram() ./drivers/gpu/drm/amd/amdkfd/kfd_migrate.c:985:58-62: ERROR: p is NULL but dereferenced.

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: fix general-protection-fault in ieee80211_subif_start_xmit() When device is running and the interface status is changed, the gpf issue is triggered. The problem triggering process is as follows: Thread A: Thread B ieee80211_runtime_change_iftype() process_one_work() ... ... ieee80211_do_stop() ... ... ... sdata->bss = NULL ... ... ieee80211_subif_start_xmit() ieee80211_multicast_to_unicast //!sdata->bss->multicast_to_unicast cause gpf issue When the interface status is changed, the sending queue continues to send packets. After the bss is set to NULL, the bss is accessed. As a result, this causes a general-protection-fault issue. The following is the stack information: general protection fault, probably for non-canonical address 0xdffffc000000002f: 0000 [#1] PREEMPT SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000178-0x000000000000017f] Workqueue: mld mld_ifc_work RIP: 0010:ieee80211_subif_start_xmit+0x25b/0x1310 Call Trace: <TASK> dev_hard_start_xmit+0x1be/0x990 __dev_queue_xmit+0x2c9a/0x3b60 ip6_finish_output2+0xf92/0x1520 ip6_finish_output+0x6af/0x11e0 ip6_output+0x1ed/0x540 mld_sendpack+0xa09/0xe70 mld_ifc_work+0x71c/0xdb0 process_one_work+0x9bf/0x1710 worker_thread+0x665/0x1080 kthread+0x2e4/0x3a0 ret_from_fork+0x1f/0x30 </TASK>

In the Linux kernel, the following vulnerability has been resolved: RDMA/hns: Fix NULL pointer problem in free_mr_init() Lock grab occurs in a concurrent scenario, resulting in stepping on a NULL pointer. It should be init mutex_init() first before use the lock. Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 Call trace: __mutex_lock.constprop.0+0xd0/0x5c0 __mutex_lock_slowpath+0x1c/0x2c mutex_lock+0x44/0x50 free_mr_send_cmd_to_hw+0x7c/0x1c0 [hns_roce_hw_v2] hns_roce_v2_dereg_mr+0x30/0x40 [hns_roce_hw_v2] hns_roce_dereg_mr+0x4c/0x130 [hns_roce_hw_v2] ib_dereg_mr_user+0x54/0x124 uverbs_free_mr+0x24/0x30 destroy_hw_idr_uobject+0x38/0x74 uverbs_destroy_uobject+0x48/0x1c4 uobj_destroy+0x74/0xcc ib_uverbs_cmd_verbs+0x368/0xbb0 ib_uverbs_ioctl+0xec/0x1a4 __arm64_sys_ioctl+0xb4/0x100 invoke_syscall+0x50/0x120 el0_svc_common.constprop.0+0x58/0x190 do_el0_svc+0x30/0x90 el0_svc+0x2c/0xb4 el0t_64_sync_handler+0x1a4/0x1b0 el0t_64_sync+0x19c/0x1a0

In the Linux kernel, the following vulnerability has been resolved: pinctrl: renesas: rzn1: Fix possible null-ptr-deref in sh_pfc_map_resources() It will cause null-ptr-deref when using 'res', if platform_get_resource() returns NULL, so move using 'res' after devm_ioremap_resource() that will check it to avoid null-ptr-deref. And use devm_platform_get_and_ioremap_resource() to simplify code.

In the Linux kernel, the following vulnerability has been resolved: media: venus: hfi: avoid null dereference in deinit If venus_probe fails at pm_runtime_put_sync the error handling first calls hfi_destroy and afterwards hfi_core_deinit. As hfi_destroy sets core->ops to NULL, hfi_core_deinit cannot call the core_deinit function anymore. Avoid this null pointer derefence by skipping the call when necessary.

In the Linux kernel, the following vulnerability has been resolved: net: ethernet: stmmac: fix altr_tse_pcs function when using a fixed-link When using a fixed-link, the altr_tse_pcs driver crashes due to null-pointer dereference as no phy_device is provided to tse_pcs_fix_mac_speed function. Fix this by adding a check for phy_dev before calling the tse_pcs_fix_mac_speed() function. Also clean up the tse_pcs_fix_mac_speed function a bit. There is no need to check for splitter_base and sgmii_adapter_base because the driver will fail if these 2 variables are not derived from the device tree.

In the Linux kernel, the following vulnerability has been resolved: drm/rockchip: vop: fix possible null-ptr-deref in vop_bind() It will cause null-ptr-deref in resource_size(), if platform_get_resource() returns NULL, move calling resource_size() after devm_ioremap_resource() that will check 'res' to avoid null-ptr-deref.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/cs: make commands with 0 chunks illegal behaviour. Submitting a cs with 0 chunks, causes an oops later, found trying to execute the wrong userspace driver. MESA_LOADER_DRIVER_OVERRIDE=v3d glxinfo [172536.665184] BUG: kernel NULL pointer dereference, address: 00000000000001d8 [172536.665188] #PF: supervisor read access in kernel mode [172536.665189] #PF: error_code(0x0000) - not-present page [172536.665191] PGD 6712a0067 P4D 6712a0067 PUD 5af9ff067 PMD 0 [172536.665195] Oops: 0000 [#1] SMP NOPTI [172536.665197] CPU: 7 PID: 2769838 Comm: glxinfo Tainted: P O 5.10.81 #1-NixOS [172536.665199] Hardware name: To be filled by O.E.M. To be filled by O.E.M./CROSSHAIR V FORMULA-Z, BIOS 2201 03/23/2015 [172536.665272] RIP: 0010:amdgpu_cs_ioctl+0x96/0x1ce0 [amdgpu] [172536.665274] Code: 75 18 00 00 4c 8b b2 88 00 00 00 8b 46 08 48 89 54 24 68 49 89 f7 4c 89 5c 24 60 31 d2 4c 89 74 24 30 85 c0 0f 85 c0 01 00 00 <48> 83 ba d8 01 00 00 00 48 8b b4 24 90 00 00 00 74 16 48 8b 46 10 [172536.665276] RSP: 0018:ffffb47c0e81bbe0 EFLAGS: 00010246 [172536.665277] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000 [172536.665278] RDX: 0000000000000000 RSI: ffffb47c0e81be28 RDI: ffffb47c0e81bd68 [172536.665279] RBP: ffff936524080010 R08: 0000000000000000 R09: ffffb47c0e81be38 [172536.665281] R10: ffff936524080010 R11: ffff936524080000 R12: ffffb47c0e81bc40 [172536.665282] R13: ffffb47c0e81be28 R14: ffff9367bc410000 R15: ffffb47c0e81be28 [172536.665283] FS: 00007fe35e05d740(0000) GS:ffff936c1edc0000(0000) knlGS:0000000000000000 [172536.665284] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [172536.665286] CR2: 00000000000001d8 CR3: 0000000532e46000 CR4: 00000000000406e0 [172536.665287] Call Trace: [172536.665322] ? amdgpu_cs_find_mapping+0x110/0x110 [amdgpu] [172536.665332] drm_ioctl_kernel+0xaa/0xf0 [drm] [172536.665338] drm_ioctl+0x201/0x3b0 [drm] [172536.665369] ? amdgpu_cs_find_mapping+0x110/0x110 [amdgpu] [172536.665372] ? selinux_file_ioctl+0x135/0x230 [172536.665399] amdgpu_drm_ioctl+0x49/0x80 [amdgpu] [172536.665403] __x64_sys_ioctl+0x83/0xb0 [172536.665406] do_syscall_64+0x33/0x40 [172536.665409] entry_SYSCALL_64_after_hwframe+0x44/0xa9 Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2018

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix a NULL pointer dereference in amdgpu_dm_connector_add_common_modes() In amdgpu_dm_connector_add_common_modes(), amdgpu_dm_create_common_mode() is assigned to mode and is passed to drm_mode_probed_add() directly after that. drm_mode_probed_add() passes &mode->head to list_add_tail(), and there is a dereference of it in list_add_tail() without recoveries, which could lead to NULL pointer dereference on failure of amdgpu_dm_create_common_mode(). Fix this by adding a NULL check of mode. This bug was found by a static analyzer. Builds with 'make allyesconfig' show no new warnings, and our static analyzer no longer warns about this code.

In the Linux kernel, the following vulnerability has been resolved: SUNRPC: Fix the svc_deferred_event trace class Fix a NULL deref crash that occurs when an svc_rqst is deferred while the sunrpc tracing subsystem is enabled. svc_revisit() sets dr->xprt to NULL, so it can't be relied upon in the tracepoint to provide the remote's address. Unfortunately we can't revert the "svc_deferred_class" hunk in commit ece200ddd54b ("sunrpc: Save remote presentation address in svc_xprt for trace events") because there is now a specific check of event format specifiers for unsafe dereferences. The warning that check emits is: event svc_defer_recv has unsafe dereference of argument 1 A "%pISpc" format specifier with a "struct sockaddr *" is indeed flagged by this check. Instead, take the brute-force approach used by the svcrdma_qp_error tracepoint. Convert the dr::addr field into a presentation address in the TP_fast_assign() arm of the trace event, and store that as a string. This fix can be backported to -stable kernels. In the meantime, commit c6ced22997ad ("tracing: Update print fmt check to handle new __get_sockaddr() macro") is now in v5.18, so this wonky fix can be replaced with __sockaddr() and friends properly during the v5.19 merge window.

In the Linux kernel, the following vulnerability has been resolved: drm/v3d: Fix null pointer dereference of pointer perfmon In the unlikely event that pointer perfmon is null the WARN_ON return path occurs after the pointer has already been deferenced. Fix this by only dereferencing perfmon after it has been null checked.

In the Linux kernel, the following vulnerability has been resolved: rtc: cmos: Fix event handler registration ordering issue Because acpi_install_fixed_event_handler() enables the event automatically on success, it is incorrect to call it before the handler routine passed to it is ready to handle events. Unfortunately, the rtc-cmos driver does exactly the incorrect thing by calling cmos_wake_setup(), which passes rtc_handler() to acpi_install_fixed_event_handler(), before cmos_do_probe(), because rtc_handler() uses dev_get_drvdata() to get to the cmos object pointer and the driver data pointer is only populated in cmos_do_probe(). This leads to a NULL pointer dereference in rtc_handler() on boot if the RTC fixed event happens to be active at the init time. To address this issue, change the initialization ordering of the driver so that cmos_wake_setup() is always called after a successful cmos_do_probe() call. While at it, change cmos_pnp_probe() to call cmos_do_probe() after the initial if () statement used for computing the IRQ argument to be passed to cmos_do_probe() which is cleaner than calling it in each branch of that if () (local variable "irq" can be of type int, because it is passed to that function as an argument of type int). Note that commit 6492fed7d8c9 ("rtc: rtc-cmos: Do not check ACPI_FADT_LOW_POWER_S0") caused this issue to affect a larger number of systems, because previously it only affected systems with ACPI_FADT_LOW_POWER_S0 set, but it is present regardless of that commit.

In the Linux kernel, the following vulnerability has been resolved: drm/msm/disp/dpu1: avoid clearing hw interrupts if hw_intr is null during drm uninit If edp modeset init is failed due to panel being not ready and probe defers during drm bind, avoid clearing irqs and dereference hw_intr when hw_intr is null. BUG: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 Call trace: dpu_core_irq_uninstall+0x50/0xb0 dpu_irq_uninstall+0x18/0x24 msm_drm_uninit+0xd8/0x16c msm_drm_bind+0x580/0x5fc try_to_bring_up_master+0x168/0x1c0 __component_add+0xb4/0x178 component_add+0x1c/0x28 dp_display_probe+0x38c/0x400 platform_probe+0xb0/0xd0 really_probe+0xcc/0x2c8 __driver_probe_device+0xbc/0xe8 driver_probe_device+0x48/0xf0 __device_attach_driver+0xa0/0xc8 bus_for_each_drv+0x8c/0xd8 __device_attach+0xc4/0x150 device_initial_probe+0x1c/0x28 Changes in V2: - Update commit message and coreect fixes tag. Patchwork: https://patchwork.freedesktop.org/patch/484430/

In the Linux kernel, the following vulnerability has been resolved: drm/msm: Fix null pointer dereferences without iommu Check if 'aspace' is set before using it as it will stay null without IOMMU, such as on msm8974.

In the Linux kernel, the following vulnerability has been resolved: ice: always check VF VSI pointer values The ice_get_vf_vsi function can return NULL in some cases, such as if handling messages during a reset where the VSI is being removed and recreated. Several places throughout the driver do not bother to check whether this VSI pointer is valid. Static analysis tools maybe report issues because they detect paths where a potentially NULL pointer could be dereferenced. Fix this by checking the return value of ice_get_vf_vsi everywhere.

In the Linux kernel, the following vulnerability has been resolved: mac802154: fix missing INIT_LIST_HEAD in ieee802154_if_add() Kernel fault injection test reports null-ptr-deref as follows: BUG: kernel NULL pointer dereference, address: 0000000000000008 RIP: 0010:cfg802154_netdev_notifier_call+0x120/0x310 include/linux/list.h:114 Call Trace: <TASK> raw_notifier_call_chain+0x6d/0xa0 kernel/notifier.c:87 call_netdevice_notifiers_info+0x6e/0xc0 net/core/dev.c:1944 unregister_netdevice_many_notify+0x60d/0xcb0 net/core/dev.c:1982 unregister_netdevice_queue+0x154/0x1a0 net/core/dev.c:10879 register_netdevice+0x9a8/0xb90 net/core/dev.c:10083 ieee802154_if_add+0x6ed/0x7e0 net/mac802154/iface.c:659 ieee802154_register_hw+0x29c/0x330 net/mac802154/main.c:229 mcr20a_probe+0xaaa/0xcb1 drivers/net/ieee802154/mcr20a.c:1316 ieee802154_if_add() allocates wpan_dev as netdev's private data, but not init the list in struct wpan_dev. cfg802154_netdev_notifier_call() manage the list when device register/unregister, and may lead to null-ptr-deref. Use INIT_LIST_HEAD() on it to initialize it correctly.

In the Linux kernel, the following vulnerability has been resolved: drm/msm/dsi: invalid parameter check in msm_dsi_phy_enable The function performs a check on the "phy" input parameter, however, it is used before the check. Initialize the "dev" variable after the sanity check to avoid a possible NULL pointer dereference. Addresses-Coverity-ID: 1493860 ("Null pointer dereference")