An issue was discovered in the Linux kernel 3.16 through 5.5.6. set_fdc in drivers/block/floppy.c leads to a wait_til_ready out-of-bounds read because the FDC index is not checked for errors before assigning it, aka CID-2e90ca68b0d2.

In the Linux kernel, the following vulnerability has been resolved: rcu: Fix buffer overflow in print_cpu_stall_info() The rcuc-starvation output from print_cpu_stall_info() might overflow the buffer if there is a huge difference in jiffies difference. The situation might seem improbable, but computers sometimes get very confused about time, which can result in full-sized integers, and, in this case, buffer overflow. Also, the unsigned jiffies difference is printed using %ld, which is normally for signed integers. This is intentional for debugging purposes, but it is not obvious from the code. This commit therefore changes sprintf() to snprintf() and adds a clarifying comment about intention of %ld format. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: tty: serial: qcom-geni-serial: fix slab-out-of-bounds on RX FIFO buffer Driver's probe allocates memory for RX FIFO (port->rx_fifo) based on default RX FIFO depth, e.g. 16. Later during serial startup the qcom_geni_serial_port_setup() updates the RX FIFO depth (port->rx_fifo_depth) to match real device capabilities, e.g. to 32. The RX UART handle code will read "port->rx_fifo_depth" number of words into "port->rx_fifo" buffer, thus exceeding the bounds. This can be observed in certain configurations with Qualcomm Bluetooth HCI UART device and KASAN: Bluetooth: hci0: QCA Product ID :0x00000010 Bluetooth: hci0: QCA SOC Version :0x400a0200 Bluetooth: hci0: QCA ROM Version :0x00000200 Bluetooth: hci0: QCA Patch Version:0x00000d2b Bluetooth: hci0: QCA controller version 0x02000200 Bluetooth: hci0: QCA Downloading qca/htbtfw20.tlv bluetooth hci0: Direct firmware load for qca/htbtfw20.tlv failed with error -2 Bluetooth: hci0: QCA Failed to request file: qca/htbtfw20.tlv (-2) Bluetooth: hci0: QCA Failed to download patch (-2) ================================================================== BUG: KASAN: slab-out-of-bounds in handle_rx_uart+0xa8/0x18c Write of size 4 at addr ffff279347d578c0 by task swapper/0/0 CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.1.0-rt5-00350-gb2450b7e00be-dirty #26 Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT) Call trace: dump_backtrace.part.0+0xe0/0xf0 show_stack+0x18/0x40 dump_stack_lvl+0x8c/0xb8 print_report+0x188/0x488 kasan_report+0xb4/0x100 __asan_store4+0x80/0xa4 handle_rx_uart+0xa8/0x18c qcom_geni_serial_handle_rx+0x84/0x9c qcom_geni_serial_isr+0x24c/0x760 __handle_irq_event_percpu+0x108/0x500 handle_irq_event+0x6c/0x110 handle_fasteoi_irq+0x138/0x2cc generic_handle_domain_irq+0x48/0x64 If the RX FIFO depth changes after probe, be sure to resize the buffer.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to do sanity check on i_extra_isize in is_alive() syzbot found a f2fs bug: BUG: KASAN: slab-out-of-bounds in data_blkaddr fs/f2fs/f2fs.h:2891 [inline] BUG: KASAN: slab-out-of-bounds in is_alive fs/f2fs/gc.c:1117 [inline] BUG: KASAN: slab-out-of-bounds in gc_data_segment fs/f2fs/gc.c:1520 [inline] BUG: KASAN: slab-out-of-bounds in do_garbage_collect+0x386a/0x3df0 fs/f2fs/gc.c:1734 Read of size 4 at addr ffff888076557568 by task kworker/u4:3/52 CPU: 1 PID: 52 Comm: kworker/u4:3 Not tainted 6.1.0-rc4-syzkaller-00362-gfef7fd48922d #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022 Workqueue: writeback wb_workfn (flush-7:0) Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 print_address_description mm/kasan/report.c:284 [inline] print_report+0x15e/0x45d mm/kasan/report.c:395 kasan_report+0xbb/0x1f0 mm/kasan/report.c:495 data_blkaddr fs/f2fs/f2fs.h:2891 [inline] is_alive fs/f2fs/gc.c:1117 [inline] gc_data_segment fs/f2fs/gc.c:1520 [inline] do_garbage_collect+0x386a/0x3df0 fs/f2fs/gc.c:1734 f2fs_gc+0x88c/0x20a0 fs/f2fs/gc.c:1831 f2fs_balance_fs+0x544/0x6b0 fs/f2fs/segment.c:410 f2fs_write_inode+0x57e/0xe20 fs/f2fs/inode.c:753 write_inode fs/fs-writeback.c:1440 [inline] __writeback_single_inode+0xcfc/0x1440 fs/fs-writeback.c:1652 writeback_sb_inodes+0x54d/0xf90 fs/fs-writeback.c:1870 wb_writeback+0x2c5/0xd70 fs/fs-writeback.c:2044 wb_do_writeback fs/fs-writeback.c:2187 [inline] wb_workfn+0x2dc/0x12f0 fs/fs-writeback.c:2227 process_one_work+0x9bf/0x1710 kernel/workqueue.c:2289 worker_thread+0x665/0x1080 kernel/workqueue.c:2436 kthread+0x2e4/0x3a0 kernel/kthread.c:376 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:306 The root cause is that we forgot to do sanity check on .i_extra_isize in below path, result in accessing invalid address later, fix it. - gc_data_segment - is_alive - data_blkaddr - offset_in_addr