In the Linux kernel, the following vulnerability has been resolved: clk: bcm: rpi: Add NULL check in raspberrypi_clk_register() devm_kasprintf() returns NULL when memory allocation fails. Currently, raspberrypi_clk_register() does not check for this case, which results in a NULL pointer dereference. Add NULL check after devm_kasprintf() to prevent this issue.

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7996: Fix null-ptr-deref in mt7996_mmio_wed_init() devm_ioremap() returns NULL on error. Currently, mt7996_mmio_wed_init() does not check for this case, which results in a NULL pointer dereference. Prevent null pointer dereference in mt7996_mmio_wed_init()

In the Linux kernel, the following vulnerability has been resolved: driver core: fix potential NULL pointer dereference in dev_uevent() If userspace reads "uevent" device attribute at the same time as another threads unbinds the device from its driver, change to dev->driver from a valid pointer to NULL may result in crash. Fix this by using READ_ONCE() when fetching the pointer, and take bus' drivers klist lock to make sure driver instance will not disappear while we access it. Use WRITE_ONCE() when setting the driver pointer to ensure there is no tearing.

A NULL pointer dereference issue was discovered in the Linux kernel in the MPTCP protocol when traversing the subflow list at disconnect time. A local user could use this flaw to potentially crash the system causing a denial of service.

A null pointer dereference issue was discovered in fs/io_uring.c in the Linux kernel before 5.15.62. A local user could use this flaw to crash the system or potentially cause a denial of service.

In the Linux kernel, the following vulnerability has been resolved: ublk: fix NULL pointer dereference in ublk_ctrl_set_size() ublk_ctrl_set_size() unconditionally dereferences ub->ub_disk via set_capacity_and_notify() without checking if it is NULL. ub->ub_disk is NULL before UBLK_CMD_START_DEV completes (it is only assigned in ublk_ctrl_start_dev()) and after UBLK_CMD_STOP_DEV runs (ublk_detach_disk() sets it to NULL). Since the UBLK_CMD_UPDATE_SIZE handler performs no state validation, a user can trigger a NULL pointer dereference by sending UPDATE_SIZE to a device that has been added but not yet started, or one that has been stopped. Fix this by checking ub->ub_disk under ub->mutex before dereferencing it, and returning -ENODEV if the disk is not available.

An issue was discovered in the Linux kernel brcm_nvram_parse in drivers/nvmem/brcm_nvram.c. Lacks for the check of the return value of kzalloc() can cause the NULL Pointer Dereference.

A NULL pointer dereference vulnerability was found in vmwgfx driver in drivers/gpu/vmxgfx/vmxgfx_execbuf.c in GPU component of Linux kernel with device file '/dev/dri/renderD128 (or Dxxx)'. This flaw allows a local attacker with a user account on the system to gain privilege, causing a denial of service(DoS).

In the Linux kernel, the following vulnerability has been resolved: can: dev: can_get_echo_skb(): prevent call to kfree_skb() in hard IRQ context If a driver calls can_get_echo_skb() during a hardware IRQ (which is often, but not always, the case), the 'WARN_ON(in_irq)' in net/core/skbuff.c#skb_release_head_state() might be triggered, under network congestion circumstances, together with the potential risk of a NULL pointer dereference. The root cause of this issue is the call to kfree_skb() instead of dev_kfree_skb_irq() in net/core/dev.c#enqueue_to_backlog(). This patch prevents the skb to be freed within the call to netif_rx() by incrementing its reference count with skb_get(). The skb is finally freed by one of the in-irq-context safe functions: dev_consume_skb_any() or dev_kfree_skb_any(). The "any" version is used because some drivers might call can_get_echo_skb() in a normal context. The reason for this issue to occur is that initially, in the core network stack, loopback skb were not supposed to be received in hardware IRQ context. The CAN stack is an exeption. This bug was previously reported back in 2017 in [1] but the proposed patch never got accepted. While [1] directly modifies net/core/dev.c, we try to propose here a smoother modification local to CAN network stack (the assumption behind is that only CAN devices are affected by this issue). [1] http://lore.kernel.org/r/57a3ffb6-3309-3ad5-5a34-e93c3fe3614d@cetitec.com

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: renesas_usb3: validate endpoint index in standard request handlers The GET_STATUS and SET/CLEAR_FEATURE handlers extract the endpoint number from the host-supplied wIndex without any sort of validation. Fix this up by validating the number of endpoints actually match up with the number the device has before attempting to dereference a pointer based on this math. This is just like what was done in commit ee0d382feb44 ("usb: gadget: aspeed_udc: validate endpoint index for ast udc") for the aspeed driver.

In the Linux kernel, the following vulnerability has been resolved: net: ethernet: mtk_ppe: avoid NULL deref when gmac0 is disabled If the gmac0 is disabled, the precheck for a valid ingress device will cause a NULL pointer deref and crash the system. This happens because eth->netdev[0] will be NULL but the code will directly try to access netdev_ops. Instead of just checking for the first net_device, it must be checked if any of the mtk_eth net_devices is matching the netdev_ops of the ingress device.

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix NULL i_assoc_inode dereference in nilfs_mdt_save_to_shadow_map The DAT inode's btree node cache (i_assoc_inode) is initialized lazily during btree operations. However, nilfs_mdt_save_to_shadow_map() assumes i_assoc_inode is already initialized when copying dirty pages to the shadow map during GC. If NILFS_IOCTL_CLEAN_SEGMENTS is called immediately after mount before any btree operation has occurred on the DAT inode, i_assoc_inode is NULL leading to a general protection fault. Fix this by calling nilfs_attach_btree_node_cache() on the DAT inode in nilfs_dat_read() at mount time, ensuring i_assoc_inode is always initialized before any GC operation can use it.

In the Linux kernel, the following vulnerability has been resolved: EDAC/mc: Fix error path ordering in edac_mc_alloc() When the mci->pvt_info allocation in edac_mc_alloc() fails, the error path will call put_device() which will end up calling the device's release function. However, the init ordering is wrong such that device_initialize() happens *after* the failed allocation and thus the device itself and the release function pointer are not initialized yet when they're called: MCE: In-kernel MCE decoding enabled. ------------[ cut here ]------------ kobject: '(null)': is not initialized, yet kobject_put() is being called. WARNING: lib/kobject.c:734 at kobject_put, CPU#22: systemd-udevd CPU: 22 UID: 0 PID: 538 Comm: systemd-udevd Not tainted 7.0.0-rc1+ #2 PREEMPT(full) RIP: 0010:kobject_put Call Trace: <TASK> edac_mc_alloc+0xbe/0xe0 [edac_core] amd64_edac_init+0x7a4/0xff0 [amd64_edac] ? __pfx_amd64_edac_init+0x10/0x10 [amd64_edac] do_one_initcall ... Reorder the calling sequence so that the device is initialized and thus the release function pointer is properly set before it can be used. This was found by Claude while reviewing another EDAC patch.

In the Linux kernel, the following vulnerability has been resolved: media: vidtv: fix NULL pointer dereference in vidtv_channel_pmt_match_sections syzbot reported a general protection fault in vidtv_psi_desc_assign [1]. vidtv_psi_pmt_stream_init() can return NULL on memory allocation failure, but vidtv_channel_pmt_match_sections() does not check for this. When tail is NULL, the subsequent call to vidtv_psi_desc_assign(&tail->descriptor, desc) dereferences a NULL pointer offset, causing a general protection fault. Add a NULL check after vidtv_psi_pmt_stream_init(). On failure, clean up the already-allocated stream chain and return. [1] Oops: general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] SMP KASAN PTI KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] RIP: 0010:vidtv_psi_desc_assign+0x24/0x90 drivers/media/test-drivers/vidtv/vidtv_psi.c:629 Call Trace: <TASK> vidtv_channel_pmt_match_sections drivers/media/test-drivers/vidtv/vidtv_channel.c:349 [inline] vidtv_channel_si_init+0x1445/0x1a50 drivers/media/test-drivers/vidtv/vidtv_channel.c:479 vidtv_mux_init+0x526/0xbe0 drivers/media/test-drivers/vidtv/vidtv_mux.c:519 vidtv_start_streaming drivers/media/test-drivers/vidtv/vidtv_bridge.c:194 [inline] vidtv_start_feed+0x33e/0x4d0 drivers/media/test-drivers/vidtv/vidtv_bridge.c:239

In the Linux kernel, the following vulnerability has been resolved: mm/damon/sysfs: check contexts->nr in repeat_call_fn damon_sysfs_repeat_call_fn() calls damon_sysfs_upd_tuned_intervals(), damon_sysfs_upd_schemes_stats(), and damon_sysfs_upd_schemes_effective_quotas() without checking contexts->nr. If nr_contexts is set to 0 via sysfs while DAMON is running, these functions dereference contexts_arr[0] and cause a NULL pointer dereference. Add the missing check. For example, the issue can be reproduced using DAMON sysfs interface and DAMON user-space tool (damo) [1] like below. $ sudo damo start --refresh_interval 1s $ echo 0 | sudo tee \ /sys/kernel/mm/damon/admin/kdamonds/0/contexts/nr_contexts

In the Linux kernel, the following vulnerability has been resolved: LoongArch: Fix missing NULL checks for kstrdup() 1. Replace "of_find_node_by_path("/")" with "of_root" to avoid multiple calls to "of_node_put()". 2. Fix a potential kernel oops during early boot when memory allocation fails while parsing CPU model from device tree.

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: u_ether: Fix NULL pointer deref in eth_get_drvinfo Commit ec35c1969650 ("usb: gadget: f_ncm: Fix net_device lifecycle with device_move") reparents the gadget device to /sys/devices/virtual during unbind, clearing the gadget pointer. If the userspace tool queries on the surviving interface during this detached window, this leads to a NULL pointer dereference. Unable to handle kernel NULL pointer dereference Call trace: eth_get_drvinfo+0x50/0x90 ethtool_get_drvinfo+0x5c/0x1f0 __dev_ethtool+0xaec/0x1fe0 dev_ethtool+0x134/0x2e0 dev_ioctl+0x338/0x560 Add a NULL check for dev->gadget in eth_get_drvinfo(). When detached, skip copying the fw_version and bus_info strings, which is natively handled by ethtool_get_drvinfo for empty strings.

In the Linux kernel, the following vulnerability has been resolved: wireguard: device: use exit_rtnl callback instead of manual rtnl_lock in pre_exit wg_netns_pre_exit() manually acquires rtnl_lock() inside the pernet .pre_exit callback. This causes a hung task when another thread holds rtnl_mutex - the cleanup_net workqueue (or the setup_net failure rollback path) blocks indefinitely in wg_netns_pre_exit() waiting to acquire the lock. Convert to .exit_rtnl, introduced in commit 7a60d91c690b ("net: Add ->exit_rtnl() hook to struct pernet_operations."), where the framework already holds RTNL and batches all callbacks under a single rtnl_lock()/rtnl_unlock() pair, eliminating the contention window. The rcu_assign_pointer(wg->creating_net, NULL) is safe to move from .pre_exit to .exit_rtnl (which runs after synchronize_rcu()) because all RCU readers of creating_net either use maybe_get_net() - which returns NULL for a dying namespace with zero refcount - or access net->user_ns which remains valid throughout the entire ops_undo_list sequence. [ Jason: added __net_exit and __read_mostly annotations that were missing. ]

In the Linux kernel, the following vulnerability has been resolved: HID: alps: fix NULL pointer dereference in alps_raw_event() Commit ecfa6f34492c ("HID: Add HID_CLAIMED_INPUT guards in raw_event callbacks missing them") attempted to fix up the HID drivers that had missed the previous fix that was done in 2ff5baa9b527 ("HID: appleir: Fix potential NULL dereference at raw event handle"), but the alps driver was missed. Fix this up by properly checking in the hid-alps driver that it had been claimed correctly before attempting to process the raw event.

In the Linux kernel, the following vulnerability has been resolved: KVM: SEV: Protect *all* of sev_mem_enc_register_region() with kvm->lock Take and hold kvm->lock for before checking sev_guest() in sev_mem_enc_register_region(), as sev_guest() isn't stable unless kvm->lock is held (or KVM can guarantee KVM_SEV_INIT{2} has completed and can't rollack state). If KVM_SEV_INIT{2} fails, KVM can end up trying to add to a not-yet-initialized sev->regions_list, e.g. triggering a #GP Oops: general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] SMP KASAN NOPTI KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] CPU: 110 UID: 0 PID: 72717 Comm: syz.15.11462 Tainted: G U W O 6.16.0-smp-DEV #1 NONE Tainted: [U]=USER, [W]=WARN, [O]=OOT_MODULE Hardware name: Google, Inc. Arcadia_IT_80/Arcadia_IT_80, BIOS 12.52.0-0 10/28/2024 RIP: 0010:sev_mem_enc_register_region+0x3f0/0x4f0 ../include/linux/list.h:83 Code: <41> 80 3c 04 00 74 08 4c 89 ff e8 f1 c7 a2 00 49 39 ed 0f 84 c6 00 RSP: 0018:ffff88838647fbb8 EFLAGS: 00010256 RAX: dffffc0000000000 RBX: 1ffff92015cf1e0b RCX: dffffc0000000000 RDX: 0000000000000000 RSI: 0000000000001000 RDI: ffff888367870000 RBP: ffffc900ae78f050 R08: ffffea000d9e0007 R09: 1ffffd4001b3c000 R10: dffffc0000000000 R11: fffff94001b3c001 R12: 0000000000000000 R13: ffff8982ab0bde00 R14: ffffc900ae78f058 R15: 0000000000000000 FS: 00007f34e9dc66c0(0000) GS:ffff89ee64d33000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fe180adef98 CR3: 000000047210e000 CR4: 0000000000350ef0 Call Trace: <TASK> kvm_arch_vm_ioctl+0xa72/0x1240 ../arch/x86/kvm/x86.c:7371 kvm_vm_ioctl+0x649/0x990 ../virt/kvm/kvm_main.c:5363 __se_sys_ioctl+0x101/0x170 ../fs/ioctl.c:51 do_syscall_x64 ../arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0x6f/0x1f0 ../arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7f34e9f7e9a9 Code: <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 a8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f34e9dc6038 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 00007f34ea1a6080 RCX: 00007f34e9f7e9a9 RDX: 0000200000000280 RSI: 000000008010aebb RDI: 0000000000000007 RBP: 00007f34ea000d69 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 0000000000000000 R14: 00007f34ea1a6080 R15: 00007ffce77197a8 </TASK> with a syzlang reproducer that looks like: syz_kvm_add_vcpu$x86(0x0, &(0x7f0000000040)={0x0, &(0x7f0000000180)=ANY=[], 0x70}) (async) syz_kvm_add_vcpu$x86(0x0, &(0x7f0000000080)={0x0, &(0x7f0000000180)=ANY=[@ANYBLOB="..."], 0x4f}) (async) r0 = openat$kvm(0xffffffffffffff9c, &(0x7f0000000200), 0x0, 0x0) r1 = ioctl$KVM_CREATE_VM(r0, 0xae01, 0x0) r2 = openat$kvm(0xffffffffffffff9c, &(0x7f0000000240), 0x0, 0x0) r3 = ioctl$KVM_CREATE_VM(r2, 0xae01, 0x0) ioctl$KVM_SET_CLOCK(r3, 0xc008aeba, &(0x7f0000000040)={0x1, 0x8, 0x0, 0x5625e9b0}) (async) ioctl$KVM_SET_PIT2(r3, 0x8010aebb, &(0x7f0000000280)={[...], 0x5}) (async) ioctl$KVM_SET_PIT2(r1, 0x4070aea0, 0x0) (async) r4 = ioctl$KVM_CREATE_VM(0xffffffffffffffff, 0xae01, 0x0) openat$kvm(0xffffffffffffff9c, 0x0, 0x0, 0x0) (async) ioctl$KVM_SET_USER_MEMORY_REGION(r4, 0x4020ae46, &(0x7f0000000400)={0x0, 0x0, 0x0, 0x2000, &(0x7f0000001000/0x2000)=nil}) (async) r5 = ioctl$KVM_CREATE_VCPU(r4, 0xae41, 0x2) close(r0) (async) openat$kvm(0xffffffffffffff9c, &(0x7f0000000000), 0x8000, 0x0) (async) ioctl$KVM_SET_GUEST_DEBUG(r5, 0x4048ae9b, &(0x7f0000000300)={0x4376ea830d46549b, 0x0, [0x46, 0x0, 0x0, 0x0, 0x0, 0x1000]}) (async) ioctl$KVM_RUN(r5, 0xae80, 0x0) Opportunistically use guard() to avoid having to define a new error label and goto usage.

In the Linux kernel, the following vulnerability has been resolved: btrfs: set BTRFS_ROOT_ORPHAN_CLEANUP during subvol create We have recently observed a number of subvolumes with broken dentries. ls-ing the parent dir looks like: drwxrwxrwt 1 root root 16 Jan 23 16:49 . drwxr-xr-x 1 root root 24 Jan 23 16:48 .. d????????? ? ? ? ? ? broken_subvol and similarly stat-ing the file fails. In this state, deleting the subvol fails with ENOENT, but attempting to create a new file or subvol over it errors out with EEXIST and even aborts the fs. Which leaves us a bit stuck. dmesg contains a single notable error message reading: "could not do orphan cleanup -2" 2 is ENOENT and the error comes from the failure handling path of btrfs_orphan_cleanup(), with the stack leading back up to btrfs_lookup(). btrfs_lookup btrfs_lookup_dentry btrfs_orphan_cleanup // prints that message and returns -ENOENT After some detailed inspection of the internal state, it became clear that: - there are no orphan items for the subvol - the subvol is otherwise healthy looking, it is not half-deleted or anything, there is no drop progress, etc. - the subvol was created a while ago and does the meaningful first btrfs_orphan_cleanup() call that sets BTRFS_ROOT_ORPHAN_CLEANUP much later. - after btrfs_orphan_cleanup() fails, btrfs_lookup_dentry() returns -ENOENT, which results in a negative dentry for the subvolume via d_splice_alias(NULL, dentry), leading to the observed behavior. The bug can be mitigated by dropping the dentry cache, at which point we can successfully delete the subvolume if we want. i.e., btrfs_lookup() btrfs_lookup_dentry() if (!sb_rdonly(inode->vfs_inode)->vfs_inode) btrfs_orphan_cleanup(sub_root) test_and_set_bit(BTRFS_ROOT_ORPHAN_CLEANUP) btrfs_search_slot() // finds orphan item for inode N ... prints "could not do orphan cleanup -2" if (inode == ERR_PTR(-ENOENT)) inode = NULL; return d_splice_alias(NULL, dentry) // NEGATIVE DENTRY for valid subvolume btrfs_orphan_cleanup() does test_and_set_bit(BTRFS_ROOT_ORPHAN_CLEANUP) on the root when it runs, so it cannot run more than once on a given root, so something else must run concurrently. However, the obvious routes to deleting an orphan when nlinks goes to 0 should not be able to run without first doing a lookup into the subvolume, which should run btrfs_orphan_cleanup() and set the bit. The final important observation is that create_subvol() calls d_instantiate_new() but does not set BTRFS_ROOT_ORPHAN_CLEANUP, so if the dentry cache gets dropped, the next lookup into the subvolume will make a real call into btrfs_orphan_cleanup() for the first time. This opens up the possibility of concurrently deleting the inode/orphan items but most typical evict() paths will be holding a reference on the parent dentry (child dentry holds parent->d_lockref.count via dget in d_alloc(), released in __dentry_kill()) and prevent the parent from being removed from the dentry cache. The one exception is delayed iputs. Ordered extent creation calls igrab() on the inode. If the file is unlinked and closed while those refs are held, iput() in __dentry_kill() decrements i_count but does not trigger eviction (i_count > 0). The child dentry is freed and the subvol dentry's d_lockref.count drops to 0, making it evictable while the inode is still alive. Since there are two races (the race between writeback and unlink and the race between lookup and delayed iputs), and there are too many moving parts, the following three diagrams show the complete picture. (Only the second and third are races) Phase 1: Create Subvol in dentry cache without BTRFS_ROOT_ORPHAN_CLEANUP set btrfs_mksubvol() lookup_one_len() __lookup_slow() d_alloc_parallel() __d_alloc() // d_lockref.count = 1 create_subvol(dentry) // doesn't touch the bit.. d_instantiate_new(dentry, inode) // dentry in cache with d_lockref.c ---truncated---

In the Linux kernel, the following vulnerability has been resolved: i2c: cp2615: fix serial string NULL-deref at probe The cp2615 driver uses the USB device serial string as the i2c adapter name but does not make sure that the string exists. Verify that the device has a serial number before accessing it to avoid triggering a NULL-pointer dereference (e.g. with malicious devices).

kernel/trace/ftrace.c in the Linux kernel before 2.6.35.5, when debugfs is enabled, does not properly handle interaction between mutex possession and llseek operations, which allows local users to cause a denial of service (NULL pointer dereference and outage of all function tracing files) via an lseek call on a file descriptor associated with the set_ftrace_filter file.

In the Linux kernel, the following vulnerability has been resolved: tracing: Drain deferred trigger frees if kthread creation fails Boot-time trigger registration can fail before the trigger-data cleanup kthread exists. Deferring those frees until late init is fine, but the post-boot fallback must still drain the deferred list if kthread creation never succeeds. Otherwise, boot-deferred nodes can accumulate on trigger_data_free_list, later frees fall back to synchronously freeing only the current object, and the older queued entries are leaked forever. To trigger this, add the following to the kernel command line: trace_event=sched_switch trace_trigger=sched_switch.traceon,sched_switch.traceon The second traceon trigger will fail and be freed. This triggers a NULL pointer dereference and crashes the kernel. Keep the deferred boot-time behavior, but when kthread creation fails, drain the whole queued list synchronously. Do the same in the late-init drain path so queued entries are not stranded there either.

In the Linux kernel, the following vulnerability has been resolved: firmware: arm_scmi: Fix NULL dereference on notify error path Since commit b5daf93b809d1 ("firmware: arm_scmi: Avoid notifier registration for unsupported events") the call chains leading to the helper __scmi_event_handler_get_ops expect an ERR_PTR to be returned on failure to get an handler for the requested event key, while the current helper can still return a NULL when no handler could be found or created. Fix by forcing an ERR_PTR return value when the handler reference is NULL.

In the Linux kernel, the following vulnerability has been resolved: auxdisplay: line-display: fix NULL dereference in linedisp_release linedisp_release() currently retrieves the enclosing struct linedisp via to_linedisp(). That lookup depends on the attachment list, but the attachment may already have been removed before put_device() invokes the release callback. This can happen in linedisp_unregister(), and can also be reached from some linedisp_register() error paths. In that case, to_linedisp() returns NULL and linedisp_release() dereferences it while freeing the display resources. The struct device released here is the embedded linedisp->dev used by linedisp_register(), so retrieve the enclosing object directly with container_of() instead.

In the Linux kernel, the following vulnerability has been resolved: mm/damon/sysfs: check contexts->nr before accessing contexts_arr[0] Multiple sysfs command paths dereference contexts_arr[0] without first verifying that kdamond->contexts->nr == 1. A user can set nr_contexts to 0 via sysfs while DAMON is running, causing NULL pointer dereferences. In more detail, the issue can be triggered by privileged users like below. First, start DAMON and make contexts directory empty (kdamond->contexts->nr == 0). # damo start # cd /sys/kernel/mm/damon/admin/kdamonds/0 # echo 0 > contexts/nr_contexts Then, each of below commands will cause the NULL pointer dereference. # echo update_schemes_stats > state # echo update_schemes_tried_regions > state # echo update_schemes_tried_bytes > state # echo update_schemes_effective_quotas > state # echo update_tuned_intervals > state Guard all commands (except OFF) at the entry point of damon_sysfs_handle_cmd().

In the Linux kernel, the following vulnerability has been resolved: usb: cdns3: gadget: fix NULL pointer dereference in ep_queue When the gadget endpoint is disabled or not yet configured, the ep->desc pointer can be NULL. This leads to a NULL pointer dereference when __cdns3_gadget_ep_queue() is called, causing a kernel crash. Add a check to return -ESHUTDOWN if ep->desc is NULL, which is the standard return code for unconfigured endpoints. This prevents potential crashes when ep_queue is called on endpoints that are not ready.

In the Linux kernel, the following vulnerability has been resolved: net: lan966x: fix page_pool error handling in lan966x_fdma_rx_alloc_page_pool() page_pool_create() can return an ERR_PTR on failure. The return value is used unconditionally in the loop that follows, passing the error pointer through xdp_rxq_info_reg_mem_model() into page_pool_use_xdp_mem(), which dereferences it, causing a kernel oops. Add an IS_ERR check after page_pool_create() to return early on failure.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Change AMDGPU_VA_RESERVED_TRAP_SIZE to 64KB Currently, AMDGPU_VA_RESERVED_TRAP_SIZE is hardcoded to 8KB, while KFD_CWSR_TBA_TMA_SIZE is defined as 2 * PAGE_SIZE. On systems with 4K pages, both values match (8KB), so allocation and reserved space are consistent. However, on 64K page-size systems, KFD_CWSR_TBA_TMA_SIZE becomes 128KB, while the reserved trap area remains 8KB. This mismatch causes the kernel to crash when running rocminfo or rccl unit tests. Kernel attempted to read user page (2) - exploit attempt? (uid: 1001) BUG: Kernel NULL pointer dereference on read at 0x00000002 Faulting instruction address: 0xc0000000002c8a64 Oops: Kernel access of bad area, sig: 11 [#1] LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries CPU: 34 UID: 1001 PID: 9379 Comm: rocminfo Tainted: G E 6.19.0-rc4-amdgpu-00320-gf23176405700 #56 VOLUNTARY Tainted: [E]=UNSIGNED_MODULE Hardware name: IBM,9105-42A POWER10 (architected) 0x800200 0xf000006 of:IBM,FW1060.30 (ML1060_896) hv:phyp pSeries NIP: c0000000002c8a64 LR: c00000000125dbc8 CTR: c00000000125e730 REGS: c0000001e0957580 TRAP: 0300 Tainted: G E MSR: 8000000000009033 <SF,EE,ME,IR,DR,RI,LE> CR: 24008268 XER: 00000036 CFAR: c00000000125dbc4 DAR: 0000000000000002 DSISR: 40000000 IRQMASK: 1 GPR00: c00000000125d908 c0000001e0957820 c0000000016e8100 c00000013d814540 GPR04: 0000000000000002 c00000013d814550 0000000000000045 0000000000000000 GPR08: c00000013444d000 c00000013d814538 c00000013d814538 0000000084002268 GPR12: c00000000125e730 c000007e2ffd5f00 ffffffffffffffff 0000000000020000 GPR16: 0000000000000000 0000000000000002 c00000015f653000 0000000000000000 GPR20: c000000138662400 c00000013d814540 0000000000000000 c00000013d814500 GPR24: 0000000000000000 0000000000000002 c0000001e0957888 c0000001e0957878 GPR28: c00000013d814548 0000000000000000 c00000013d814540 c0000001e0957888 NIP [c0000000002c8a64] __mutex_add_waiter+0x24/0xc0 LR [c00000000125dbc8] __mutex_lock.constprop.0+0x318/0xd00 Call Trace: 0xc0000001e0957890 (unreliable) __mutex_lock.constprop.0+0x58/0xd00 amdgpu_amdkfd_gpuvm_alloc_memory_of_gpu+0x6fc/0xb60 [amdgpu] kfd_process_alloc_gpuvm+0x54/0x1f0 [amdgpu] kfd_process_device_init_cwsr_dgpu+0xa4/0x1a0 [amdgpu] kfd_process_device_init_vm+0xd8/0x2e0 [amdgpu] kfd_ioctl_acquire_vm+0xd0/0x130 [amdgpu] kfd_ioctl+0x514/0x670 [amdgpu] sys_ioctl+0x134/0x180 system_call_exception+0x114/0x300 system_call_vectored_common+0x15c/0x2ec This patch changes AMDGPU_VA_RESERVED_TRAP_SIZE to 64 KB and KFD_CWSR_TBA_TMA_SIZE to the AMD GPU page size. This means we reserve 64 KB for the trap in the address space, but only allocate 8 KB within it. With this approach, the allocation size never exceeds the reserved area. (cherry picked from commit 31b8de5e55666f26ea7ece5f412b83eab3f56dbb)

In the Linux kernel, the following vulnerability has been resolved: net: bonding: fix NULL deref in bond_debug_rlb_hash_show rlb_clear_slave intentionally keeps RLB hash-table entries on the rx_hashtbl_used_head list with slave set to NULL when no replacement slave is available. However, bond_debug_rlb_hash_show visites client_info->slave without checking if it's NULL. Other used-list iterators in bond_alb.c already handle this NULL-slave state safely: - rlb_update_client returns early on !client_info->slave - rlb_req_update_slave_clients, rlb_clear_slave, and rlb_rebalance compare slave values before visiting - lb_req_update_subnet_clients continues if slave is NULL The following NULL deref crash can be trigger in bond_debug_rlb_hash_show: [ 1.289791] BUG: kernel NULL pointer dereference, address: 0000000000000000 [ 1.292058] RIP: 0010:bond_debug_rlb_hash_show (drivers/net/bonding/bond_debugfs.c:41) [ 1.293101] RSP: 0018:ffffc900004a7d00 EFLAGS: 00010286 [ 1.293333] RAX: 0000000000000000 RBX: ffff888102b48200 RCX: ffff888102b48204 [ 1.293631] RDX: ffff888102b48200 RSI: ffffffff839daad5 RDI: ffff888102815078 [ 1.293924] RBP: ffff888102815078 R08: ffff888102b4820e R09: 0000000000000000 [ 1.294267] R10: 0000000000000000 R11: 0000000000000000 R12: ffff888100f929c0 [ 1.294564] R13: ffff888100f92a00 R14: 0000000000000001 R15: ffffc900004a7ed8 [ 1.294864] FS: 0000000001395380(0000) GS:ffff888196e75000(0000) knlGS:0000000000000000 [ 1.295239] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1.295480] CR2: 0000000000000000 CR3: 0000000102adc004 CR4: 0000000000772ef0 [ 1.295897] Call Trace: [ 1.296134] seq_read_iter (fs/seq_file.c:231) [ 1.296341] seq_read (fs/seq_file.c:164) [ 1.296493] full_proxy_read (fs/debugfs/file.c:378 (discriminator 1)) [ 1.296658] vfs_read (fs/read_write.c:572) [ 1.296981] ksys_read (fs/read_write.c:717) [ 1.297132] do_syscall_64 (arch/x86/entry/syscall_64.c:63 (discriminator 1) arch/x86/entry/syscall_64.c:94 (discriminator 1)) [ 1.297325] entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130) Add a NULL check and print "(none)" for entries with no assigned slave.

In the Linux kernel, the following vulnerability has been resolved: comedi: ni_atmio16d: Fix invalid clean-up after failed attach If the driver's COMEDI "attach" handler function (`atmio16d_attach()`) returns an error, the COMEDI core will call the driver's "detach" handler function (`atmio16d_detach()`) to clean up. This calls `reset_atmio16d()` unconditionally, but depending on where the error occurred in the attach handler, the device may not have been sufficiently initialized to call `reset_atmio16d()`. It uses `dev->iobase` as the I/O port base address and `dev->private` as the pointer to the COMEDI device's private data structure. `dev->iobase` may still be set to its initial value of 0, which would result in undesired writes to low I/O port addresses. `dev->private` may still be `NULL`, which would result in null pointer dereferences. Fix `atmio16d_detach()` by checking that `dev->private` is valid (non-null) before calling `reset_atmio16d()`. This implies that `dev->iobase` was set correctly since that is set up before `dev->private`.

In the Linux kernel, the following vulnerability has been resolved: drm/mediatek: dsi: Store driver data before invoking mipi_dsi_host_register The call to mipi_dsi_host_register triggers a callback to mtk_dsi_bind, which uses dev_get_drvdata to retrieve the mtk_dsi struct, so this structure needs to be stored inside the driver data before invoking it. As drvdata is currently uninitialized it leads to a crash when registering the DSI DRM encoder right after acquiring the mode_config.idr_mutex, blocking all subsequent DRM operations. Fixes the following crash during mediatek-drm probe (tested on Xiaomi Smart Clock x04g): Unable to handle kernel NULL pointer dereference at virtual address 0000000000000040 [...] Modules linked in: mediatek_drm(+) drm_display_helper cec drm_client_lib drm_dma_helper drm_kms_helper panel_simple [...] Call trace: drm_mode_object_add+0x58/0x98 (P) __drm_encoder_init+0x48/0x140 drm_encoder_init+0x6c/0xa0 drm_simple_encoder_init+0x20/0x34 [drm_kms_helper] mtk_dsi_bind+0x34/0x13c [mediatek_drm] component_bind_all+0x120/0x280 mtk_drm_bind+0x284/0x67c [mediatek_drm] try_to_bring_up_aggregate_device+0x23c/0x320 __component_add+0xa4/0x198 component_add+0x14/0x20 mtk_dsi_host_attach+0x78/0x100 [mediatek_drm] mipi_dsi_attach+0x2c/0x50 panel_simple_dsi_probe+0x4c/0x9c [panel_simple] mipi_dsi_drv_probe+0x1c/0x28 really_probe+0xc0/0x3dc __driver_probe_device+0x80/0x160 driver_probe_device+0x40/0x120 __device_attach_driver+0xbc/0x17c bus_for_each_drv+0x88/0xf0 __device_attach+0x9c/0x1cc device_initial_probe+0x54/0x60 bus_probe_device+0x34/0xa0 device_add+0x5b0/0x800 mipi_dsi_device_register_full+0xdc/0x16c mipi_dsi_host_register+0xc4/0x17c mtk_dsi_probe+0x10c/0x260 [mediatek_drm] platform_probe+0x5c/0xa4 really_probe+0xc0/0x3dc __driver_probe_device+0x80/0x160 driver_probe_device+0x40/0x120 __driver_attach+0xc8/0x1f8 bus_for_each_dev+0x7c/0xe0 driver_attach+0x24/0x30 bus_add_driver+0x11c/0x240 driver_register+0x68/0x130 __platform_register_drivers+0x64/0x160 mtk_drm_init+0x24/0x1000 [mediatek_drm] do_one_initcall+0x60/0x1d0 do_init_module+0x54/0x240 load_module+0x1838/0x1dc0 init_module_from_file+0xd8/0xf0 __arm64_sys_finit_module+0x1b4/0x428 invoke_syscall.constprop.0+0x48/0xc8 do_el0_svc+0x3c/0xb8 el0_svc+0x34/0xe8 el0t_64_sync_handler+0xa0/0xe4 el0t_64_sync+0x198/0x19c Code: 52800022 941004ab 2a0003f3 37f80040 (29005a80)

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix null-ptr-deref in block_dirty_buffer tracepoint When using the "block:block_dirty_buffer" tracepoint, mark_buffer_dirty() may cause a NULL pointer dereference, or a general protection fault when KASAN is enabled. This happens because, since the tracepoint was added in mark_buffer_dirty(), it references the dev_t member bh->b_bdev->bd_dev regardless of whether the buffer head has a pointer to a block_device structure. In the current implementation, nilfs_grab_buffer(), which grabs a buffer to read (or create) a block of metadata, including b-tree node blocks, does not set the block device, but instead does so only if the buffer is not in the "uptodate" state for each of its caller block reading functions. However, if the uptodate flag is set on a folio/page, and the buffer heads are detached from it by try_to_free_buffers(), and new buffer heads are then attached by create_empty_buffers(), the uptodate flag may be restored to each buffer without the block device being set to bh->b_bdev, and mark_buffer_dirty() may be called later in that state, resulting in the bug mentioned above. Fix this issue by making nilfs_grab_buffer() always set the block device of the super block structure to the buffer head, regardless of the state of the buffer's uptodate flag.

In the Linux kernel, the following vulnerability has been resolved: bridge: guard local VLAN-0 FDB helpers against NULL vlan group When CONFIG_BRIDGE_VLAN_FILTERING is not set, br_vlan_group() and nbp_vlan_group() return NULL (br_private.h stub definitions). The BR_BOOLOPT_FDB_LOCAL_VLAN_0 toggle code is compiled unconditionally and reaches br_fdb_delete_locals_per_vlan_port() and br_fdb_insert_locals_per_vlan_port(), where the NULL vlan group pointer is dereferenced via list_for_each_entry(v, &vg->vlan_list, vlist). The observed crash is in the delete path, triggered when creating a bridge with IFLA_BR_MULTI_BOOLOPT containing BR_BOOLOPT_FDB_LOCAL_VLAN_0 via RTM_NEWLINK. The insert helper has the same bug pattern. Oops: general protection fault, probably for non-canonical address 0xdffffc0000000056: 0000 [#1] KASAN NOPTI KASAN: null-ptr-deref in range [0x00000000000002b0-0x00000000000002b7] RIP: 0010:br_fdb_delete_locals_per_vlan+0x2b9/0x310 Call Trace: br_fdb_toggle_local_vlan_0+0x452/0x4c0 br_toggle_fdb_local_vlan_0+0x31/0x80 net/bridge/br.c:276 br_boolopt_toggle net/bridge/br.c:313 br_boolopt_multi_toggle net/bridge/br.c:364 br_changelink net/bridge/br_netlink.c:1542 br_dev_newlink net/bridge/br_netlink.c:1575 Add NULL checks for the vlan group pointer in both helpers, returning early when there are no VLANs to iterate. This matches the existing pattern used by other bridge FDB functions such as br_fdb_add() and br_fdb_delete().

A vulnerability was found in Linux Kernel where in the spk_ttyio_receive_buf2() function, it would dereference spk_ttyio_synth without checking whether it is NULL or not, and may lead to a NULL-ptr deref crash.

In the Linux kernel, the following vulnerability has been resolved: tracing: kprobe: Fix potential null-ptr-deref on trace_event_file in kprobe_event_gen_test_exit() When trace_get_event_file() failed, gen_kretprobe_test will be assigned as the error code. If module kprobe_event_gen_test is removed now, the null pointer dereference will happen in kprobe_event_gen_test_exit(). Check if gen_kprobe_test or gen_kretprobe_test is error code or NULL before dereference them. BUG: kernel NULL pointer dereference, address: 0000000000000012 PGD 0 P4D 0 Oops: 0000 [#1] SMP PTI CPU: 3 PID: 2210 Comm: modprobe Not tainted 6.1.0-rc1-00171-g2159299a3b74-dirty #217 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014 RIP: 0010:kprobe_event_gen_test_exit+0x1c/0xb5 [kprobe_event_gen_test] Code: Unable to access opcode bytes at 0xffffffff9ffffff2. RSP: 0018:ffffc900015bfeb8 EFLAGS: 00010246 RAX: ffffffffffffffea RBX: ffffffffa0002080 RCX: 0000000000000000 RDX: ffffffffa0001054 RSI: ffffffffa0001064 RDI: ffffffffdfc6349c RBP: ffffffffa0000000 R08: 0000000000000004 R09: 00000000001e95c0 R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000800 R13: ffffffffa0002420 R14: 0000000000000000 R15: 0000000000000000 FS: 00007f56b75be540(0000) GS:ffff88813bc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffff9ffffff2 CR3: 000000010874a006 CR4: 0000000000330ee0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> __x64_sys_delete_module+0x206/0x380 ? lockdep_hardirqs_on_prepare+0xd8/0x190 ? syscall_enter_from_user_mode+0x1c/0x50 do_syscall_64+0x3f/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd

In the Linux kernel, the following vulnerability has been resolved: ACPI: processor: Fix previous acpi_processor_errata_piix4() fix After commi f132e089fe89 ("ACPI: processor: Fix NULL-pointer dereference in acpi_processor_errata_piix4()"), device pointers may be dereferenced after dropping references to the device objects pointed to by them, which may cause a use-after-free to occur. Moreover, debug messages about enabling the errata may be printed if the errata flags corresponding to them are unset. Address all of these issues by moving message printing to the points in the code where the errata flags are set.

In the Linux kernel, the following vulnerability has been resolved: udp_tunnel: fix NULL deref caused by udp_sock_create6 when CONFIG_IPV6=n When CONFIG_IPV6 is disabled, the udp_sock_create6() function returns 0 (success) without actually creating a socket. Callers such as fou_create() then proceed to dereference the uninitialized socket pointer, resulting in a NULL pointer dereference. The captured NULL deref crash: BUG: kernel NULL pointer dereference, address: 0000000000000018 RIP: 0010:fou_nl_add_doit (net/ipv4/fou_core.c:590 net/ipv4/fou_core.c:764) [...] Call Trace: <TASK> genl_family_rcv_msg_doit.constprop.0 (net/netlink/genetlink.c:1114) genl_rcv_msg (net/netlink/genetlink.c:1194 net/netlink/genetlink.c:1209) [...] netlink_rcv_skb (net/netlink/af_netlink.c:2550) genl_rcv (net/netlink/genetlink.c:1219) netlink_unicast (net/netlink/af_netlink.c:1319 net/netlink/af_netlink.c:1344) netlink_sendmsg (net/netlink/af_netlink.c:1894) __sock_sendmsg (net/socket.c:727 (discriminator 1) net/socket.c:742 (discriminator 1)) __sys_sendto (./include/linux/file.h:62 (discriminator 1) ./include/linux/file.h:83 (discriminator 1) net/socket.c:2183 (discriminator 1)) __x64_sys_sendto (net/socket.c:2213 (discriminator 1) net/socket.c:2209 (discriminator 1) net/socket.c:2209 (discriminator 1)) do_syscall_64 (arch/x86/entry/syscall_64.c:63 (discriminator 1) arch/x86/entry/syscall_64.c:94 (discriminator 1)) entry_SYSCALL_64_after_hwframe (net/arch/x86/entry/entry_64.S:130) This patch makes udp_sock_create6 return -EPFNOSUPPORT instead, so callers correctly take their error paths. There is only one caller of the vulnerable function and only privileged users can trigger it.

In the Linux kernel, the following vulnerability has been resolved: ipv6: add NULL checks for idev in SRv6 paths __in6_dev_get() can return NULL when the device has no IPv6 configuration (e.g. MTU < IPV6_MIN_MTU or after NETDEV_UNREGISTER). Add NULL checks for idev returned by __in6_dev_get() in both seg6_hmac_validate_skb() and ipv6_srh_rcv() to prevent potential NULL pointer dereferences.

In the Linux kernel, the following vulnerability has been resolved: arm_mpam: Fix null pointer dereference when restoring bandwidth counters When an MSC supporting memory bandwidth monitoring is brought offline and then online, mpam_restore_mbwu_state() calls __ris_msmon_read() via ipi to restore the configuration of the bandwidth counters. It doesn't care about the value read, mbwu_arg.val, and doesn't set it leading to a null pointer dereference when __ris_msmon_read() adds to it. This results in a kernel oops with a call trace such as: Call trace: __ris_msmon_read+0x19c/0x64c (P) mpam_restore_mbwu_state+0xa0/0xe8 smp_call_on_cpu_callback+0x1c/0x38 process_one_work+0x154/0x4b4 worker_thread+0x188/0x310 kthread+0x11c/0x130 ret_from_fork+0x10/0x20 Provide a local variable for val to avoid __ris_msmon_read() dereferencing a null pointer when adding to val.

NVIDIA GPU Display Driver for Linux contains a vulnerability in the kernel mode layer handler, where an unhandled return value can lead to a null-pointer dereference, which may lead to denial of service.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix NULL pointer dereference in dcn401_init_hw() dcn401_init_hw() assumes that update_bw_bounding_box() is valid when entering the update path. However, the existing condition: ((!fams2_enable && update_bw_bounding_box) || freq_changed) does not guarantee this, as the freq_changed branch can evaluate to true independently of the callback pointer. This can result in calling update_bw_bounding_box() when it is NULL. Fix this by separating the update condition from the pointer checks and ensuring the callback, dc->clk_mgr, and bw_params are validated before use. Fixes the below: ../dc/hwss/dcn401/dcn401_hwseq.c:367 dcn401_init_hw() error: we previously assumed 'dc->res_pool->funcs->update_bw_bounding_box' could be null (see line 362) (cherry picked from commit 86117c5ab42f21562fedb0a64bffea3ee5fcd477)

NVIDIA GPU Display Driver for Windows and Linux contains a vulnerability in the kernel mode layer, where an unprivileged user can cause a null-pointer dereference, which may lead to denial of service.

In the Linux kernel, the following vulnerability has been resolved: idpf: Fix RSS LUT NULL ptr issue after soft reset During soft reset, the RSS LUT is freed and not restored unless the interface is up. If an ethtool command that accesses the rss lut is attempted immediately after reset, it will result in NULL ptr dereference. Also, there is no need to reset the rss lut if the soft reset does not involve queue count change. After soft reset, set the RSS LUT to default values based on the updated queue count only if the reset was a result of a queue count change and the LUT was not configured by the user. In all other cases, don't touch the LUT. Steps to reproduce: ** Bring the interface down (if up) ifconfig eth1 down ** update the queue count (eg., 27->20) ethtool -L eth1 combined 20 ** display the RSS LUT ethtool -x eth1 [82375.558338] BUG: kernel NULL pointer dereference, address: 0000000000000000 [82375.558373] #PF: supervisor read access in kernel mode [82375.558391] #PF: error_code(0x0000) - not-present page [82375.558408] PGD 0 P4D 0 [82375.558421] Oops: Oops: 0000 [#1] SMP NOPTI <snip> [82375.558516] RIP: 0010:idpf_get_rxfh+0x108/0x150 [idpf] [82375.558786] Call Trace: [82375.558793] <TASK> [82375.558804] rss_prepare.isra.0+0x187/0x2a0 [82375.558827] rss_prepare_data+0x3a/0x50 [82375.558845] ethnl_default_doit+0x13d/0x3e0 [82375.558863] genl_family_rcv_msg_doit+0x11f/0x180 [82375.558886] genl_rcv_msg+0x1ad/0x2b0 [82375.558902] ? __pfx_ethnl_default_doit+0x10/0x10 [82375.558920] ? __pfx_genl_rcv_msg+0x10/0x10 [82375.558937] netlink_rcv_skb+0x58/0x100 [82375.558957] genl_rcv+0x2c/0x50 [82375.558971] netlink_unicast+0x289/0x3e0 [82375.558988] netlink_sendmsg+0x215/0x440 [82375.559005] __sys_sendto+0x234/0x240 [82375.559555] __x64_sys_sendto+0x28/0x30 [82375.560068] x64_sys_call+0x1909/0x1da0 [82375.560576] do_syscall_64+0x7a/0xfa0 [82375.561076] ? clear_bhb_loop+0x60/0xb0 [82375.561567] entry_SYSCALL_64_after_hwframe+0x76/0x7e <snip>

In the Linux kernel, the following vulnerability has been resolved: net: marvell: prestera: fix NULL dereference on devlink_alloc() failure devlink_alloc() may return NULL on allocation failure, but prestera_devlink_alloc() unconditionally calls devlink_priv() on the returned pointer. This leads to a NULL pointer dereference if devlink allocation fails. Add a check for a NULL devlink pointer and return NULL early to avoid the crash.

In the Linux kernel, the following vulnerability has been resolved: perf: sched: Fix perf crash with new is_user_task() helper In order to do a user space stacktrace the current task needs to be a user task that has executed in user space. It use to be possible to test if a task is a user task or not by simply checking the task_struct mm field. If it was non NULL, it was a user task and if not it was a kernel task. But things have changed over time, and some kernel tasks now have their own mm field. An idea was made to instead test PF_KTHREAD and two functions were used to wrap this check in case it became more complex to test if a task was a user task or not[1]. But this was rejected and the C code simply checked the PF_KTHREAD directly. It was later found that not all kernel threads set PF_KTHREAD. The io-uring helpers instead set PF_USER_WORKER and this needed to be added as well. But checking the flags is still not enough. There's a very small window when a task exits that it frees its mm field and it is set back to NULL. If perf were to trigger at this moment, the flags test would say its a user space task but when perf would read the mm field it would crash with at NULL pointer dereference. Now there are flags that can be used to test if a task is exiting, but they are set in areas that perf may still want to profile the user space task (to see where it exited). The only real test is to check both the flags and the mm field. Instead of making this modification in every location, create a new is_user_task() helper function that does all the tests needed to know if it is safe to read the user space memory or not. [1] https://lore.kernel.org/all/20250425204120.639530125@goodmis.org/

In the Linux kernel, the following vulnerability has been resolved: idpf: detach and close netdevs while handling a reset Protect the reset path from callbacks by setting the netdevs to detached state and close any netdevs in UP state until the reset handling has completed. During a reset, the driver will de-allocate resources for the vport, and there is no guarantee that those will recover, which is why the existing vport_ctrl_lock does not provide sufficient protection. idpf_detach_and_close() is called right before reset handling. If the reset handling succeeds, the netdevs state is recovered via call to idpf_attach_and_open(). If the reset handling fails the netdevs remain down. The detach/down calls are protected with RTNL lock to avoid racing with callbacks. On the recovery side the attach can be done without holding the RTNL lock as there are no callbacks expected at that point, due to detach/close always being done first in that flow. The previous logic restoring the netdevs state based on the IDPF_VPORT_UP_REQUESTED flag in the init task is not needed anymore, hence the removal of idpf_set_vport_state(). The IDPF_VPORT_UP_REQUESTED is still being used to restore the state of the netdevs following the reset, but has no use outside of the reset handling flow. idpf_init_hard_reset() is converted to void, since it was used as such and there is no error handling being done based on its return value. Before this change, invoking hard and soft resets simultaneously will cause the driver to lose the vport state: ip -br a <inf> UP echo 1 > /sys/class/net/ens801f0/device/reset& \ ethtool -L ens801f0 combined 8 ip -br a <inf> DOWN ip link set <inf> up ip -br a <inf> DOWN Also in case of a failure in the reset path, the netdev is left exposed to external callbacks, while vport resources are not initialized, leading to a crash on subsequent ifup/down: [408471.398966] idpf 0000:83:00.0: HW reset detected [408471.411744] idpf 0000:83:00.0: Device HW Reset initiated [408472.277901] idpf 0000:83:00.0: The driver was unable to contact the device's firmware. Check that the FW is running. Driver state= 0x2 [408508.125551] BUG: kernel NULL pointer dereference, address: 0000000000000078 [408508.126112] #PF: supervisor read access in kernel mode [408508.126687] #PF: error_code(0x0000) - not-present page [408508.127256] PGD 2aae2f067 P4D 0 [408508.127824] Oops: Oops: 0000 [#1] SMP NOPTI ... [408508.130871] RIP: 0010:idpf_stop+0x39/0x70 [idpf] ... [408508.139193] Call Trace: [408508.139637] <TASK> [408508.140077] __dev_close_many+0xbb/0x260 [408508.140533] __dev_change_flags+0x1cf/0x280 [408508.140987] netif_change_flags+0x26/0x70 [408508.141434] dev_change_flags+0x3d/0xb0 [408508.141878] devinet_ioctl+0x460/0x890 [408508.142321] inet_ioctl+0x18e/0x1d0 [408508.142762] ? _copy_to_user+0x22/0x70 [408508.143207] sock_do_ioctl+0x3d/0xe0 [408508.143652] sock_ioctl+0x10e/0x330 [408508.144091] ? find_held_lock+0x2b/0x80 [408508.144537] __x64_sys_ioctl+0x96/0xe0 [408508.144979] do_syscall_64+0x79/0x3d0 [408508.145415] entry_SYSCALL_64_after_hwframe+0x76/0x7e [408508.145860] RIP: 0033:0x7f3e0bb4caff

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix NULL pointer dereference in amdgpu_gmc_filter_faults_remove On APUs such as Raven and Renoir (GC 9.1.0, 9.2.2, 9.3.0), the ih1 and ih2 interrupt ring buffers are not initialized. This is by design, as these secondary IH rings are only available on discrete GPUs. See vega10_ih_sw_init() which explicitly skips ih1/ih2 initialization when AMD_IS_APU is set. However, amdgpu_gmc_filter_faults_remove() unconditionally uses ih1 to get the timestamp of the last interrupt entry. When retry faults are enabled on APUs (noretry=0), this function is called from the SVM page fault recovery path, resulting in a NULL pointer dereference when amdgpu_ih_decode_iv_ts_helper() attempts to access ih->ring[]. The crash manifests as: BUG: kernel NULL pointer dereference, address: 0000000000000004 RIP: 0010:amdgpu_ih_decode_iv_ts_helper+0x22/0x40 [amdgpu] Call Trace: amdgpu_gmc_filter_faults_remove+0x60/0x130 [amdgpu] svm_range_restore_pages+0xae5/0x11c0 [amdgpu] amdgpu_vm_handle_fault+0xc8/0x340 [amdgpu] gmc_v9_0_process_interrupt+0x191/0x220 [amdgpu] amdgpu_irq_dispatch+0xed/0x2c0 [amdgpu] amdgpu_ih_process+0x84/0x100 [amdgpu] This issue was exposed by commit 1446226d32a4 ("drm/amdgpu: Remove GC HW IP 9.3.0 from noretry=1") which changed the default for Renoir APU from noretry=1 to noretry=0, enabling retry fault handling and thus exercising the buggy code path. Fix this by adding a check for ih1.ring_size before attempting to use it. Also restore the soft_ih support from commit dd299441654f ("drm/amdgpu: Rework retry fault removal"). This is needed if the hardware doesn't support secondary HW IH rings. v2: additional updates (Alex) (cherry picked from commit 6ce8d536c80aa1f059e82184f0d1994436b1d526)

In the Linux kernel, the following vulnerability has been resolved: ipv6: Fix ECMP sibling count mismatch when clearing RTF_ADDRCONF syzbot reported a kernel BUG in fib6_add_rt2node() when adding an IPv6 route. [0] Commit f72514b3c569 ("ipv6: clear RA flags when adding a static route") introduced logic to clear RTF_ADDRCONF from existing routes when a static route with the same nexthop is added. However, this causes a problem when the existing route has a gateway. When RTF_ADDRCONF is cleared from a route that has a gateway, that route becomes eligible for ECMP, i.e. rt6_qualify_for_ecmp() returns true. The issue is that this route was never added to the fib6_siblings list. This leads to a mismatch between the following counts: - The sibling count computed by iterating fib6_next chain, which includes the newly ECMP-eligible route - The actual siblings in fib6_siblings list, which does not include that route When a subsequent ECMP route is added, fib6_add_rt2node() hits BUG_ON(sibling->fib6_nsiblings != rt->fib6_nsiblings) because the counts don't match. Fix this by only clearing RTF_ADDRCONF when the existing route does not have a gateway. Routes without a gateway cannot qualify for ECMP anyway (rt6_qualify_for_ecmp() requires fib_nh_gw_family), so clearing RTF_ADDRCONF on them is safe and matches the original intent of the commit. [0]: kernel BUG at net/ipv6/ip6_fib.c:1217! Oops: invalid opcode: 0000 [#1] SMP KASAN PTI CPU: 0 UID: 0 PID: 6010 Comm: syz.0.17 Not tainted syzkaller #0 PREEMPT(full) Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/25/2025 RIP: 0010:fib6_add_rt2node+0x3433/0x3470 net/ipv6/ip6_fib.c:1217 [...] Call Trace: <TASK> fib6_add+0x8da/0x18a0 net/ipv6/ip6_fib.c:1532 __ip6_ins_rt net/ipv6/route.c:1351 [inline] ip6_route_add+0xde/0x1b0 net/ipv6/route.c:3946 ipv6_route_ioctl+0x35c/0x480 net/ipv6/route.c:4571 inet6_ioctl+0x219/0x280 net/ipv6/af_inet6.c:577 sock_do_ioctl+0xdc/0x300 net/socket.c:1245 sock_ioctl+0x576/0x790 net/socket.c:1366 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:597 [inline] __se_sys_ioctl+0xfc/0x170 fs/ioctl.c:583 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xfa/0xf80 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f