TPLINK TL-ER5120G 4.0 2.0.0 Build 210817 Rel.80868n has a command injection vulnerability, when an attacker adds ACL rules after authentication, and the rule name parameter has injection points.

TPLINK TL-ER5120G 4.0 2.0.0 Build 210817 Rel.80868n has a command injection vulnerability, when an attacker adds NAPT rules after authentication, and the rule name has an injection point.

TP-Link TL-WPA4530 KIT V2 (EU)_170406 and V2 (EU)_161115 is vulnerable to Command Injection via _httpRpmPlcDeviceRemove.

TP-Link TL-WR940N V2/V4, TL-WR841N V8/V10, and TL-WR740N V1/V2 was discovered to contain a command injection vulnerability via the component /userRpm/WlanNetworkRpm .

An exploitable remote code execution vulnerability exists in the ping and tracert functionality of the TP-Link TL-R600VPN HWv3 FRNv1.3.0 and HWv2 FRNv1.2.3 http server. A specially crafted IP address can cause a stack overflow, resulting in remote code execution. An attacker can send a single authenticated HTTP request to trigger this vulnerability.

A vulnerability classified as critical has been found in TP-LINK Technologies TL-IPC544EP-W4 1.0.9 Build 240428 Rel 69493n. Affected is the function sub_69064 of the file /bin/main. The manipulation of the argument text leads to buffer overflow. It is possible to launch the attack remotely. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

TP-Link TL-WR902AC devices through V3 0.9.1 allow remote authenticated attackers to execute arbitrary code or cause a Denial of Service (DoS) by uploading a crafted firmware update because the signature check is inadequate.

A stack-based buffer overflow vulnerability exists in the web interface Radio Scheduling functionality of Tp-Link AC1350 Wireless MU-MIMO Gigabit Access Point (EAP225 V3) v5.1.0 Build 20220926. A specially crafted series of HTTP requests can lead to remote code execution. An attacker can make an authenticated HTTP request to trigger this vulnerability.This vulnerability refers specifically to the overflow that occurs via the `band` parameter at offset `0x0045aad8` of the `httpd_portal` binary shipped with v5.1.0 Build 20220926 of the EAP225.

A stack-based buffer overflow vulnerability exists in the web interface Radio Scheduling functionality of Tp-Link AC1350 Wireless MU-MIMO Gigabit Access Point (EAP225 V3) v5.1.0 Build 20220926. A specially crafted series of HTTP requests can lead to remote code execution. An attacker can make an authenticated HTTP request to trigger this vulnerability.This vulnerability refers specifically to the overflow that occurs via the `action` parameter at offset `0x422448` of the `httpd` binary shipped with v5.0.4 Build 20220216 of the EAP115.

A stack-based buffer overflow vulnerability exists in the web interface Radio Scheduling functionality of Tp-Link AC1350 Wireless MU-MIMO Gigabit Access Point (EAP225 V3) v5.1.0 Build 20220926. A specially crafted series of HTTP requests can lead to remote code execution. An attacker can make an authenticated HTTP request to trigger this vulnerability.This vulnerability refers specifically to the overflow that occurs via the `profile` parameter at offset `0x4224b0` of the `httpd` binary shipped with v5.0.4 Build 20220216 of the EAP115.

A stack-based buffer overflow vulnerability exists in the web interface Radio Scheduling functionality of Tp-Link AC1350 Wireless MU-MIMO Gigabit Access Point (EAP225 V3) v5.1.0 Build 20220926. A specially crafted series of HTTP requests can lead to remote code execution. An attacker can make an authenticated HTTP request to trigger this vulnerability.This vulnerability refers specifically to the overflow that occurs via the `ssid` parameter at offset `0x42247c` of the `httpd` binary shipped with v5.0.4 Build 20220216 of the EAP115.

A stack-based buffer overflow vulnerability exists in the web interface Radio Scheduling functionality of Tp-Link AC1350 Wireless MU-MIMO Gigabit Access Point (EAP225 V3) v5.1.0 Build 20220926. A specially crafted series of HTTP requests can lead to remote code execution. An attacker can make an authenticated HTTP request to trigger this vulnerability.This vulnerability refers specifically to the overflow that occurs via the `band` parameter at offset `0x422420` of the `httpd` binary shipped with v5.0.4 Build 20220216 of the EAP115.

TP Link Archer AX10 V1 Firmware Version 1.3.1 Build 20220401 Rel. 57450(5553) was discovered to allow authenticated attackers to execute arbitrary code via a crafted backup file.

A stack-based buffer overflow vulnerability exists in the web interface Radio Scheduling functionality of Tp-Link AC1350 Wireless MU-MIMO Gigabit Access Point (EAP225 V3) v5.1.0 Build 20220926. A specially crafted series of HTTP requests can lead to remote code execution. An attacker can make an authenticated HTTP request to trigger this vulnerability.This vulnerability refers specifically to the overflow that occurs via the `action` parameter at offset `0x0045ab38` of the `httpd_portal` binary shipped with v5.1.0 Build 20220926 of the EAP225.

A stack-based buffer overflow vulnerability exists in the web interface Radio Scheduling functionality of Tp-Link AC1350 Wireless MU-MIMO Gigabit Access Point (EAP225 V3) v5.1.0 Build 20220926. A specially crafted series of HTTP requests can lead to remote code execution. An attacker can make an authenticated HTTP request to trigger this vulnerability.This vulnerability refers specifically to the overflow that occurs via the `profile` parameter at offset `0x0045abc8` of the `httpd_portal` binary shipped with v5.1.0 Build 20220926 of the EAP225.

A stack-based buffer overflow vulnerability exists in the web interface Radio Scheduling functionality of Tp-Link AC1350 Wireless MU-MIMO Gigabit Access Point (EAP225 V3) v5.1.0 Build 20220926. A specially crafted series of HTTP requests can lead to remote code execution. An attacker can make an authenticated HTTP request to trigger this vulnerability.This vulnerability refers specifically to the overflow that occurs via the `ssid` parameter at offset `0x0045ab7c` of the `httpd_portal` binary shipped with v5.1.0 Build 20220926 of the EAP225.

In TP-Link Router AX50 firmware 210730 and older, import of a malicious backup file via web interface can lead to remote code execution due to improper validation.

A buffer overflow in the httpd daemon on TP-Link TL-WR841N V12 (firmware version 3.16.9) devices allows an authenticated remote attacker to execute arbitrary code via a GET request to the page for the System Tools of the Wi-Fi network. This affects TL-WR841 V12 TL-WR841N(EU)_V12_160624 and TL-WR841 V11 TL-WR841N(EU)_V11_160325 , TL-WR841N_V11_150616 and TL-WR841 V10 TL-WR841N_V10_150310 are also affected.

TP-Link JetStream Smart Switch TL-SG2210P 5.0 Build 20211201 allows attackers to escalate privileges via modification of the 'tid' and 'usrlvl' values in GET requests.

There is remote authenticated OS command injection on TP-Link Archer C20i 0.9.1 3.2 v003a.0 Build 170221 Rel.55462n devices vie the X_TP_ExternalIPv6Address HTTP parameter, allowing a remote attacker to run arbitrary commands on the router with root privileges.

httpd on TP-Link TL-WPA4220 devices (versions 2 through 4) allows remote authenticated users to execute arbitrary OS commands by sending crafted POST requests to the endpoint /admin/powerline. Fixed version: TL-WPA4220(EU)_V4_201023

TP-LINK NC200 devices through 2.1.10 build 200401, NC210 devices through 1.0.10 build 200401, NC220 devices through 1.3.1 build 200401, NC230 devices through 1.3.1 build 200401, NC250 devices through 1.3.1 build 200401, NC260 devices through 1.5.3 build_200401, and NC450 devices through 1.5.4 build 200401 have a Buffer Overflow

Certain TP-Link devices allow Command Injection. This affects NC260 1.5.2 build 200304 and NC450 1.5.3 build 200304.

Certain TP-Link devices allow Command Injection. This affects NC200 2.1.9 build 200225, NC210 1.0.9 build 200304, NC220 1.3.0 build 200304, NC230 1.3.0 build 200304, NC250 1.3.0 build 200304, NC260 1.5.2 build 200304, and NC450 1.5.3 build 200304.

TP-Link wifi router TL-WR802N V4(JP), with firmware version prior to 211202, is vulnerable to OS command injection.

A Command Injection issue in the traceroute feature on TP-Link TL-WR841N V13 (JP) with firmware versions prior to 201216 allows authenticated users to execute arbitrary code as root via shell metacharacters, a different vulnerability than CVE-2018-12577.

TP-Link Archer AX21 (AX1800) firmware versions before 1.1.4 Build 20230219 contained a command injection vulnerability in the country form of the /cgi-bin/luci;stok=/locale endpoint on the web management interface. Specifically, the country parameter of the write operation was not sanitized before being used in a call to popen(), allowing an unauthenticated attacker to inject commands, which would be run as root, with a simple POST request.

A command execution vulnerability exists in the tddpd enable_test_mode functionality of Tp-Link AC1350 Wireless MU-MIMO Gigabit Access Point (EAP225 V3) v5.1.0 Build 20220926 and Tp-Link N300 Wireless Access Point (EAP115 V4) v5.0.4 Build 20220216. A specially crafted series of network requests can lead to arbitrary command execution. An attacker can send a sequence of unauthenticated packets to trigger this vulnerability.This vulnerability impacts `uclited` on the EAP115(V4) 5.0.4 Build 20220216 of the N300 Wireless Gigabit Access Point.

TP-Link TL-WR841N ated_tp Command Injection Remote Code Execution Vulnerability. This vulnerability allows network-adjacent attackers to execute arbitrary code on affected installations of TP-Link TL-WR841N routers. Authentication is not required to exploit this vulnerability. The specific flaw exists within the ated_tp service. The issue results from the lack of proper validation of a user-supplied string before using it to execute a system call. An attacker can leverage this vulnerability to execute code in the context of root. Was ZDI-CAN-21825.

The affected device expose a network service called "rftest" that is vulnerable to unauthenticated command injection on ports TCP/8888, TCP/8889, and TCP/8890. By successfully exploiting this flaw, remote unauthenticated attacker can gain arbitrary command execution on the device with elevated privileges.This issue affects Archer C4500X: through 1_1.1.6.

TP-Link TL-WPA8630P (US)_ V2_ Version 171011 was discovered to contain a command injection vulnerability via the key parameter in the function sub_ 40A774.

A command injection issue was found in TP-Link MR3020 v.1_150921 that allows a remote attacker to execute arbitrary commands via a crafted request to the tftp endpoint.

A command execution vulnerability exists in the tddpd enable_test_mode functionality of Tp-Link AC1350 Wireless MU-MIMO Gigabit Access Point (EAP225 V3) v5.1.0 Build 20220926 and Tp-Link N300 Wireless Access Point (EAP115 V4) v5.0.4 Build 20220216. A specially crafted series of network requests can lead to arbitrary command execution. An attacker can send a sequence of unauthenticated packets to trigger this vulnerability.This vulnerability impacts `uclited` on the EAP225(V3) 5.1.0 Build 20220926 of the AC1350 Wireless MU-MIMO Gigabit Access Point.

TP-Link Tapo C200 IP camera, on its 1.1.15 firmware version and below, is affected by an unauthenticated RCE vulnerability, present in the uhttpd binary running by default as root. The exploitation of this vulnerability allows an attacker to take full control of the camera.

TP-Link TL-WPA8630P (US)_ V2_ Version 171011 was discovered to contain a command injection vulnerability via the devicePwd parameter in the function sub_ 40A80C.

TP-Link TL-IPC42C V4.0_20211227_1.0.16 is vulnerable to command injection due to the lack of malicious code verification on both the frontend and backend.

The web-based configuration interface of the TP-Link M7350 V3 with firmware before 190531 is affected by several post-authentication command injection vulnerabilities.

A vulnerability was found in TOTOLINK X15 1.0.0-B20230714.1105. It has been classified as critical. Affected is an unknown function of the file /boafrm/formMapDelDevice of the component HTTP POST Request Handler. The manipulation of the argument macstr leads to buffer overflow. It is possible to launch the attack remotely. The exploit has been disclosed to the public and may be used.

A vulnerability was found in D-Link DIR‑818L up to 1.05B01. This issue affects the function getenv of the file /htdocs/cgibin of the component ssdpcgi. The manipulation leads to command injection. The attack may be initiated remotely. The exploit has been disclosed to the public and may be used.

Multiple vulnerabilities in the web management interface of Cisco Firepower Management Center (FMC) Software could allow an authenticated, remote attacker to execute arbitrary commands on the underlying operating system. The attacker would need valid device credentials but does not require administrator privileges to exploit this vulnerability. These vulnerabilities are due to insufficient validation of user-supplied input for certain configuration options. An attacker could exploit these vulnerabilities by using crafted input within the device configuration GUI. A successful exploit could allow the attacker to execute arbitrary commands on the device including the underlying operating system which could also affect the availability of the device.

Possible Elevation of Privilege Vulnerability in iManager has been discovered in OpenText™ iManager. This impacts all versions before 3.2.5

Improper Neutralization of Special Elements used in a Command ('Command Injection') vulnerability in Liman Central Management System Liman MYS (HTTP/Controllers, CronMail, Jobs modules) allows Command Injection.This issue affects Liman Central Management System: from 1.7.0 before 1.8.3-462.

Multiple vulnerabilities in the web-based management interface of Cisco Firepower Management Center (FMC) Software could allow an authenticated, remote attacker to execute arbitrary commands on the underlying operating system. To exploit these vulnerabilities, the attacker must have valid device credentials, but does not need Administrator privileges. These vulnerabilities are due to insufficient validation of user-supplied input for certain configuration options. An attacker could exploit these vulnerabilities by using crafted input within the device configuration GUI. A successful exploit could allow the attacker to execute arbitrary commands on the device, including on the underlying operating system, which could also affect the availability of the device.

A vulnerability was found in TOTOLINK T6 4.1.5cu.748_B20211015. It has been declared as critical. This vulnerability affects the function setTracerouteCfg of the file /cgi-bin/cstecgi.cgi of the component HTTP POST Request Handler. The manipulation of the argument command leads to command injection. The attack can be initiated remotely. The exploit has been disclosed to the public and may be used.

A vulnerability classified as critical was found in Tenda O3V2 1.0.0.12(3880). This vulnerability affects the function fromNetToolGet of the file /goform/setPingInfo of the component httpd. The manipulation of the argument domain leads to os command injection. The attack can be initiated remotely. The exploit has been disclosed to the public and may be used.

A vulnerability, which was classified as critical, has been found in D-Link DI-7300G+ 19.12.25A1. Affected by this issue is some unknown functionality of the file in proxy_client.asp. The manipulation of the argument proxy_srv/proxy_lanport/proxy_lanip/proxy_srvport leads to os command injection. The attack may be launched remotely. The exploit has been disclosed to the public and may be used.

A vulnerability was found in D-Link DIR-645 up to 1.05B01 and classified as critical. This issue affects the function ssdpcgi_main of the file /htdocs/cgibin of the component ssdpcgi. The manipulation leads to command injection. The attack may be initiated remotely. The exploit has been disclosed to the public and may be used. This vulnerability only affects products that are no longer supported by the maintainer.

A vulnerability, which was classified as critical, has been found in TRENDnet TEW-652BRP 3.04B01. This issue affects some unknown processing of the file get_set.ccp of the component Web Management Interface. The manipulation leads to command injection. The attack may be initiated remotely. The exploit has been disclosed to the public and may be used. The associated identifier of this vulnerability is VDB-219935.

An authenticated remote code execution vulnerability exists in the AOS-CX Network Analytics Engine. Successful exploitation of this vulnerability results in the ability to execute arbitrary code as a privileged user on the underlying operating system, leading to a complete compromise of the switch running AOS-CX.

Command Injection in GitHub repository froxlor/froxlor prior to 2.0.8.