In the Linux kernel, the following vulnerability has been resolved: io_uring: fix ltout double free on completion race Always remove linked timeout on io_link_timeout_fn() from the master request link list, otherwise we may get use-after-free when first io_link_timeout_fn() puts linked timeout in the fail path, and then will be found and put on master's free.

In the Linux kernel, the following vulnerability has been resolved: habanalabs/gaudi: Fix a potential use after free in gaudi_memset_device_memory Our code analyzer reported a uaf. In gaudi_memset_device_memory, cb is get via hl_cb_kernel_create() with 2 refcount. If hl_cs_allocate_job() failed, the execution runs into release_cb branch. One ref of cb is dropped by hl_cb_put(cb) and could be freed if other thread also drops one ref. Then cb is used by cb->id later, which is a potential uaf. My patch add a variable 'id' to accept the value of cb->id before the hl_cb_put(cb) is called, to avoid the potential uaf.

In the Linux kernel, the following vulnerability has been resolved: sctp: do asoc update earlier in sctp_sf_do_dupcook_a There's a panic that occurs in a few of envs, the call trace is as below: [] general protection fault, ... 0x29acd70f1000a: 0000 [#1] SMP PTI [] RIP: 0010:sctp_ulpevent_notify_peer_addr_change+0x4b/0x1fa [sctp] [] sctp_assoc_control_transport+0x1b9/0x210 [sctp] [] sctp_do_8_2_transport_strike.isra.16+0x15c/0x220 [sctp] [] sctp_cmd_interpreter.isra.21+0x1231/0x1a10 [sctp] [] sctp_do_sm+0xc3/0x2a0 [sctp] [] sctp_generate_timeout_event+0x81/0xf0 [sctp] This is caused by a transport use-after-free issue. When processing a duplicate COOKIE-ECHO chunk in sctp_sf_do_dupcook_a(), both COOKIE-ACK and SHUTDOWN chunks are allocated with the transort from the new asoc. However, later in the sideeffect machine, the old asoc is used to send them out and old asoc's shutdown_last_sent_to is set to the transport that SHUTDOWN chunk attached to in sctp_cmd_setup_t2(), which actually belongs to the new asoc. After the new_asoc is freed and the old asoc T2 timeout, the old asoc's shutdown_last_sent_to that is already freed would be accessed in sctp_sf_t2_timer_expire(). Thanks Alexander and Jere for helping dig into this issue. To fix it, this patch is to do the asoc update first, then allocate the COOKIE-ACK and SHUTDOWN chunks with the 'updated' old asoc. This would make more sense, as a chunk from an asoc shouldn't be sent out with another asoc. We had fixed quite a few issues caused by this.

In the Linux kernel, the following vulnerability has been resolved: net: usb: fix possible use-after-free in smsc75xx_bind The commit 46a8b29c6306 ("net: usb: fix memory leak in smsc75xx_bind") fails to clean up the work scheduled in smsc75xx_reset-> smsc75xx_set_multicast, which leads to use-after-free if the work is scheduled to start after the deallocation. In addition, this patch also removes a dangling pointer - dev->data[0]. This patch calls cancel_work_sync to cancel the scheduled work and set the dangling pointer to NULL.

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_tables: fix use-after-free in nft_set_catchall_destroy() We need to use list_for_each_entry_safe() iterator because we can not access @catchall after kfree_rcu() call. syzbot reported: BUG: KASAN: use-after-free in nft_set_catchall_destroy net/netfilter/nf_tables_api.c:4486 [inline] BUG: KASAN: use-after-free in nft_set_destroy net/netfilter/nf_tables_api.c:4504 [inline] BUG: KASAN: use-after-free in nft_set_destroy+0x3fd/0x4f0 net/netfilter/nf_tables_api.c:4493 Read of size 8 at addr ffff8880716e5b80 by task syz-executor.3/8871 CPU: 1 PID: 8871 Comm: syz-executor.3 Not tainted 5.16.0-rc5-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 print_address_description.constprop.0.cold+0x8d/0x2ed mm/kasan/report.c:247 __kasan_report mm/kasan/report.c:433 [inline] kasan_report.cold+0x83/0xdf mm/kasan/report.c:450 nft_set_catchall_destroy net/netfilter/nf_tables_api.c:4486 [inline] nft_set_destroy net/netfilter/nf_tables_api.c:4504 [inline] nft_set_destroy+0x3fd/0x4f0 net/netfilter/nf_tables_api.c:4493 __nft_release_table+0x79f/0xcd0 net/netfilter/nf_tables_api.c:9626 nft_rcv_nl_event+0x4f8/0x670 net/netfilter/nf_tables_api.c:9688 notifier_call_chain+0xb5/0x200 kernel/notifier.c:83 blocking_notifier_call_chain kernel/notifier.c:318 [inline] blocking_notifier_call_chain+0x67/0x90 kernel/notifier.c:306 netlink_release+0xcb6/0x1dd0 net/netlink/af_netlink.c:788 __sock_release+0xcd/0x280 net/socket.c:649 sock_close+0x18/0x20 net/socket.c:1314 __fput+0x286/0x9f0 fs/file_table.c:280 task_work_run+0xdd/0x1a0 kernel/task_work.c:164 tracehook_notify_resume include/linux/tracehook.h:189 [inline] exit_to_user_mode_loop kernel/entry/common.c:175 [inline] exit_to_user_mode_prepare+0x27e/0x290 kernel/entry/common.c:207 __syscall_exit_to_user_mode_work kernel/entry/common.c:289 [inline] syscall_exit_to_user_mode+0x19/0x60 kernel/entry/common.c:300 do_syscall_64+0x42/0xb0 arch/x86/entry/common.c:86 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f75fbf28adb Code: 0f 05 48 3d 00 f0 ff ff 77 45 c3 0f 1f 40 00 48 83 ec 18 89 7c 24 0c e8 63 fc ff ff 8b 7c 24 0c 41 89 c0 b8 03 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 35 44 89 c7 89 44 24 0c e8 a1 fc ff ff 8b 44 RSP: 002b:00007ffd8da7ec10 EFLAGS: 00000293 ORIG_RAX: 0000000000000003 RAX: 0000000000000000 RBX: 0000000000000004 RCX: 00007f75fbf28adb RDX: 00007f75fc08e828 RSI: ffffffffffffffff RDI: 0000000000000003 RBP: 00007f75fc08a960 R08: 0000000000000000 R09: 00007f75fc08e830 R10: 00007ffd8da7ed10 R11: 0000000000000293 R12: 00000000002067c3 R13: 00007ffd8da7ed10 R14: 00007f75fc088f60 R15: 0000000000000032 </TASK> Allocated by task 8886: kasan_save_stack+0x1e/0x50 mm/kasan/common.c:38 kasan_set_track mm/kasan/common.c:46 [inline] set_alloc_info mm/kasan/common.c:434 [inline] ____kasan_kmalloc mm/kasan/common.c:513 [inline] ____kasan_kmalloc mm/kasan/common.c:472 [inline] __kasan_kmalloc+0xa6/0xd0 mm/kasan/common.c:522 kasan_kmalloc include/linux/kasan.h:269 [inline] kmem_cache_alloc_trace+0x1ea/0x4a0 mm/slab.c:3575 kmalloc include/linux/slab.h:590 [inline] nft_setelem_catchall_insert net/netfilter/nf_tables_api.c:5544 [inline] nft_setelem_insert net/netfilter/nf_tables_api.c:5562 [inline] nft_add_set_elem+0x232e/0x2f40 net/netfilter/nf_tables_api.c:5936 nf_tables_newsetelem+0x6ff/0xbb0 net/netfilter/nf_tables_api.c:6032 nfnetlink_rcv_batch+0x1710/0x25f0 net/netfilter/nfnetlink.c:513 nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:634 [inline] nfnetlink_rcv+0x3af/0x420 net/netfilter/nfnetlink.c:652 netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline] netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1345 netlink_sendmsg+0x904/0xdf0 net/netlink/af_netlink.c:1921 sock_sendmsg_nosec net/ ---truncated---

In the Linux kernel, the following vulnerability has been resolved: RDMA/rtrs-clt: destroy sysfs after removing session from active list A session can be removed dynamically by sysfs interface "remove_path" that eventually calls rtrs_clt_remove_path_from_sysfs function. The current rtrs_clt_remove_path_from_sysfs first removes the sysfs interfaces and frees sess->stats object. Second it removes the session from the active list. Therefore some functions could access non-connected session and access the freed sess->stats object even-if they check the session status before accessing the session. For instance rtrs_clt_request and get_next_path_min_inflight check the session status and try to send IO to the session. The session status could be changed when they are trying to send IO but they could not catch the change and update the statistics information in sess->stats object, and generate use-after-free problem. (see: "RDMA/rtrs-clt: Check state of the rtrs_clt_sess before reading its stats") This patch changes the rtrs_clt_remove_path_from_sysfs to remove the session from the active session list and then destroy the sysfs interfaces. Each function still should check the session status because closing or error recovery paths can change the status.

In the Linux kernel, the following vulnerability has been resolved: mm/damon/dbgfs: protect targets destructions with kdamond_lock DAMON debugfs interface iterates current monitoring targets in 'dbgfs_target_ids_read()' while holding the corresponding 'kdamond_lock'. However, it also destructs the monitoring targets in 'dbgfs_before_terminate()' without holding the lock. This can result in a use_after_free bug. This commit avoids the race by protecting the destruction with the corresponding 'kdamond_lock'.

In the Linux kernel, the following vulnerability has been resolved: scsi: ufs: bsg: Set bsg_queue to NULL after removal Currently, this does not cause any issues, but I believe it is necessary to set bsg_queue to NULL after removing it to prevent potential use-after-free (UAF) access.

In the Linux kernel, the following vulnerability has been resolved: regmap: set debugfs_name to NULL after it is freed There is a upstream commit cffa4b2122f5("regmap:debugfs: Fix a memory leak when calling regmap_attach_dev") that adds a if condition when create name for debugfs_name. With below function invoking logical, debugfs_name is freed in regmap_debugfs_exit(), but it is not created again because of the if condition introduced by above commit. regmap_reinit_cache() regmap_debugfs_exit() ... regmap_debugfs_init() So, set debugfs_name to NULL after it is freed.

In the Linux kernel, the following vulnerability has been resolved: ethernet:enic: Fix a use after free bug in enic_hard_start_xmit In enic_hard_start_xmit, it calls enic_queue_wq_skb(). Inside enic_queue_wq_skb, if some error happens, the skb will be freed by dev_kfree_skb(skb). But the freed skb is still used in skb_tx_timestamp(skb). My patch makes enic_queue_wq_skb() return error and goto spin_unlock() incase of error. The solution is provided by Govind. See https://lkml.org/lkml/2021/4/30/961.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix use-after-free of encap entry in neigh update handler Function mlx5e_rep_neigh_update() wasn't updated to accommodate rtnl lock removal from TC filter update path and properly handle concurrent encap entry insertion/deletion which can lead to following use-after-free: [23827.464923] ================================================================== [23827.469446] BUG: KASAN: use-after-free in mlx5e_encap_take+0x72/0x140 [mlx5_core] [23827.470971] Read of size 4 at addr ffff8881d132228c by task kworker/u20:6/21635 [23827.472251] [23827.472615] CPU: 9 PID: 21635 Comm: kworker/u20:6 Not tainted 5.13.0-rc3+ #5 [23827.473788] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 [23827.475639] Workqueue: mlx5e mlx5e_rep_neigh_update [mlx5_core] [23827.476731] Call Trace: [23827.477260] dump_stack+0xbb/0x107 [23827.477906] print_address_description.constprop.0+0x18/0x140 [23827.478896] ? mlx5e_encap_take+0x72/0x140 [mlx5_core] [23827.479879] ? mlx5e_encap_take+0x72/0x140 [mlx5_core] [23827.480905] kasan_report.cold+0x7c/0xd8 [23827.481701] ? mlx5e_encap_take+0x72/0x140 [mlx5_core] [23827.482744] kasan_check_range+0x145/0x1a0 [23827.493112] mlx5e_encap_take+0x72/0x140 [mlx5_core] [23827.494054] ? mlx5e_tc_tun_encap_info_equal_generic+0x140/0x140 [mlx5_core] [23827.495296] mlx5e_rep_neigh_update+0x41e/0x5e0 [mlx5_core] [23827.496338] ? mlx5e_rep_neigh_entry_release+0xb80/0xb80 [mlx5_core] [23827.497486] ? read_word_at_a_time+0xe/0x20 [23827.498250] ? strscpy+0xa0/0x2a0 [23827.498889] process_one_work+0x8ac/0x14e0 [23827.499638] ? lockdep_hardirqs_on_prepare+0x400/0x400 [23827.500537] ? pwq_dec_nr_in_flight+0x2c0/0x2c0 [23827.501359] ? rwlock_bug.part.0+0x90/0x90 [23827.502116] worker_thread+0x53b/0x1220 [23827.502831] ? process_one_work+0x14e0/0x14e0 [23827.503627] kthread+0x328/0x3f0 [23827.504254] ? _raw_spin_unlock_irq+0x24/0x40 [23827.505065] ? __kthread_bind_mask+0x90/0x90 [23827.505912] ret_from_fork+0x1f/0x30 [23827.506621] [23827.506987] Allocated by task 28248: [23827.507694] kasan_save_stack+0x1b/0x40 [23827.508476] __kasan_kmalloc+0x7c/0x90 [23827.509197] mlx5e_attach_encap+0xde1/0x1d40 [mlx5_core] [23827.510194] mlx5e_tc_add_fdb_flow+0x397/0xc40 [mlx5_core] [23827.511218] __mlx5e_add_fdb_flow+0x519/0xb30 [mlx5_core] [23827.512234] mlx5e_configure_flower+0x191c/0x4870 [mlx5_core] [23827.513298] tc_setup_cb_add+0x1d5/0x420 [23827.514023] fl_hw_replace_filter+0x382/0x6a0 [cls_flower] [23827.514975] fl_change+0x2ceb/0x4a51 [cls_flower] [23827.515821] tc_new_tfilter+0x89a/0x2070 [23827.516548] rtnetlink_rcv_msg+0x644/0x8c0 [23827.517300] netlink_rcv_skb+0x11d/0x340 [23827.518021] netlink_unicast+0x42b/0x700 [23827.518742] netlink_sendmsg+0x743/0xc20 [23827.519467] sock_sendmsg+0xb2/0xe0 [23827.520131] ____sys_sendmsg+0x590/0x770 [23827.520851] ___sys_sendmsg+0xd8/0x160 [23827.521552] __sys_sendmsg+0xb7/0x140 [23827.522238] do_syscall_64+0x3a/0x70 [23827.522907] entry_SYSCALL_64_after_hwframe+0x44/0xae [23827.523797] [23827.524163] Freed by task 25948: [23827.524780] kasan_save_stack+0x1b/0x40 [23827.525488] kasan_set_track+0x1c/0x30 [23827.526187] kasan_set_free_info+0x20/0x30 [23827.526968] __kasan_slab_free+0xed/0x130 [23827.527709] slab_free_freelist_hook+0xcf/0x1d0 [23827.528528] kmem_cache_free_bulk+0x33a/0x6e0 [23827.529317] kfree_rcu_work+0x55f/0xb70 [23827.530024] process_one_work+0x8ac/0x14e0 [23827.530770] worker_thread+0x53b/0x1220 [23827.531480] kthread+0x328/0x3f0 [23827.532114] ret_from_fork+0x1f/0x30 [23827.532785] [23827.533147] Last potentially related work creation: [23827.534007] kasan_save_stack+0x1b/0x40 [23827.534710] kasan_record_aux_stack+0xab/0xc0 [23827.535492] kvfree_call_rcu+0x31/0x7b0 [23827.536206] mlx5e_tc_del ---truncated---

In the Linux kernel, the following vulnerability has been resolved: spi: Fix use-after-free with devm_spi_alloc_* We can't rely on the contents of the devres list during spi_unregister_controller(), as the list is already torn down at the time we perform devres_find() for devm_spi_release_controller. This causes devices registered with devm_spi_alloc_{master,slave}() to be mistakenly identified as legacy, non-devm managed devices and have their reference counters decremented below 0. ------------[ cut here ]------------ WARNING: CPU: 1 PID: 660 at lib/refcount.c:28 refcount_warn_saturate+0x108/0x174 [<b0396f04>] (refcount_warn_saturate) from [<b03c56a4>] (kobject_put+0x90/0x98) [<b03c5614>] (kobject_put) from [<b0447b4c>] (put_device+0x20/0x24) r4:b6700140 [<b0447b2c>] (put_device) from [<b07515e8>] (devm_spi_release_controller+0x3c/0x40) [<b07515ac>] (devm_spi_release_controller) from [<b045343c>] (release_nodes+0x84/0xc4) r5:b6700180 r4:b6700100 [<b04533b8>] (release_nodes) from [<b0454160>] (devres_release_all+0x5c/0x60) r8:b1638c54 r7:b117ad94 r6:b1638c10 r5:b117ad94 r4:b163dc10 [<b0454104>] (devres_release_all) from [<b044e41c>] (__device_release_driver+0x144/0x1ec) r5:b117ad94 r4:b163dc10 [<b044e2d8>] (__device_release_driver) from [<b044f70c>] (device_driver_detach+0x84/0xa0) r9:00000000 r8:00000000 r7:b117ad94 r6:b163dc54 r5:b1638c10 r4:b163dc10 [<b044f688>] (device_driver_detach) from [<b044d274>] (unbind_store+0xe4/0xf8) Instead, determine the devm allocation state as a flag on the controller which is guaranteed to be stable during cleanup.

In the Linux kernel, the following vulnerability has been resolved: xen-netback: take a reference to the RX task thread Do this in order to prevent the task from being freed if the thread returns (which can be triggered by the frontend) before the call to kthread_stop done as part of the backend tear down. Not taking the reference will lead to a use-after-free in that scenario. Such reference was taken before but dropped as part of the rework done in 2ac061ce97f4. Reintroduce the reference taking and add a comment this time explaining why it's needed. This is XSA-374 / CVE-2021-28691.

In the Linux kernel, the following vulnerability has been resolved: net:emac/emac-mac: Fix a use after free in emac_mac_tx_buf_send In emac_mac_tx_buf_send, it calls emac_tx_fill_tpd(..,skb,..). If some error happens in emac_tx_fill_tpd(), the skb will be freed via dev_kfree_skb(skb) in error branch of emac_tx_fill_tpd(). But the freed skb is still used via skb->len by netdev_sent_queue(,skb->len). As i observed that emac_tx_fill_tpd() haven't modified the value of skb->len, thus my patch assigns skb->len to 'len' before the possible free and use 'len' instead of skb->len later.

In the Linux kernel, the following vulnerability has been resolved: ACPI: custom_method: fix potential use-after-free issue In cm_write(), buf is always freed when reaching the end of the function. If the requested count is less than table.length, the allocated buffer will be freed but subsequent calls to cm_write() will still try to access it. Remove the unconditional kfree(buf) at the end of the function and set the buf to NULL in the -EINVAL error path to match the rest of function.

In the Linux kernel, the following vulnerability has been resolved: net: dpaa2-eth: fix use-after-free in dpaa2_eth_remove Access to netdev after free_netdev() will cause use-after-free bug. Move debug log before free_netdev() call to avoid it.

In the Linux kernel, the following vulnerability has been resolved: drm/prime: Fix use after free in mmap with drm_gem_ttm_mmap drm_gem_ttm_mmap() drops a reference to the gem object on success. If the gem object's refcount == 1 on entry to drm_gem_prime_mmap(), that drop will free the gem object, and the subsequent drm_gem_object_get() will be a UAF. Fix by grabbing a reference before calling the mmap helper. This issue was forseen when the reference dropping was adding in commit 9786b65bc61ac ("drm/ttm: fix mmap refcounting"): "For that to work properly the drm_gem_object_get() call in drm_gem_ttm_mmap() must be moved so it happens before calling obj->funcs->mmap(), otherwise the gem refcount would go down to zero."

In the Linux kernel, the following vulnerability has been resolved: i40e: Fix use-after-free in i40e_client_subtask() Currently the call to i40e_client_del_instance frees the object pf->cinst, however pf->cinst->lan_info is being accessed after the free. Fix this by adding the missing return. Addresses-Coverity: ("Read from pointer after free")

In the Linux kernel, the following vulnerability has been resolved: KVM: Destroy I/O bus devices on unregister failure _after_ sync'ing SRCU If allocating a new instance of an I/O bus fails when unregistering a device, wait to destroy the device until after all readers are guaranteed to see the new null bus. Destroying devices before the bus is nullified could lead to use-after-free since readers expect the devices on their reference of the bus to remain valid.

In the Linux kernel, the following vulnerability has been resolved: net/tls: Fix use-after-free after the TLS device goes down and up When a netdev with active TLS offload goes down, tls_device_down is called to stop the offload and tear down the TLS context. However, the socket stays alive, and it still points to the TLS context, which is now deallocated. If a netdev goes up, while the connection is still active, and the data flow resumes after a number of TCP retransmissions, it will lead to a use-after-free of the TLS context. This commit addresses this bug by keeping the context alive until its normal destruction, and implements the necessary fallbacks, so that the connection can resume in software (non-offloaded) kTLS mode. On the TX side tls_sw_fallback is used to encrypt all packets. The RX side already has all the necessary fallbacks, because receiving non-decrypted packets is supported. The thing needed on the RX side is to block resync requests, which are normally produced after receiving non-decrypted packets. The necessary synchronization is implemented for a graceful teardown: first the fallbacks are deployed, then the driver resources are released (it used to be possible to have a tls_dev_resync after tls_dev_del). A new flag called TLS_RX_DEV_DEGRADED is added to indicate the fallback mode. It's used to skip the RX resync logic completely, as it becomes useless, and some objects may be released (for example, resync_async, which is allocated and freed by the driver).

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Fix use-after-free in lpfc_unreg_rpi() routine An error is detected with the following report when unloading the driver: "KASAN: use-after-free in lpfc_unreg_rpi+0x1b1b" The NLP_REG_LOGIN_SEND nlp_flag is set in lpfc_reg_fab_ctrl_node(), but the flag is not cleared upon completion of the login. This allows a second call to lpfc_unreg_rpi() to proceed with nlp_rpi set to LPFC_RPI_ALLOW_ERROR. This results in a use after free access when used as an rpi_ids array index. Fix by clearing the NLP_REG_LOGIN_SEND nlp_flag in lpfc_mbx_cmpl_fc_reg_login().

In the Linux kernel, the following vulnerability has been resolved: bus: mhi: core: Fix invalid error returning in mhi_queue mhi_queue returns an error when the doorbell is not accessible in the current state. This can happen when the device is in non M0 state, like M3, and needs to be waken-up prior ringing the DB. This case is managed earlier by triggering an asynchronous M3 exit via controller resume/suspend callbacks, that in turn will cause M0 transition and DB update. So, since it's not an error but just delaying of doorbell update, there is no reason to return an error. This also fixes a use after free error for skb case, indeed a caller queuing skb will try to free the skb if the queueing fails, but in that case queueing has been done.

In the Linux kernel, the following vulnerability has been resolved: net/nfc: fix use-after-free llcp_sock_bind/connect Commits 8a4cd82d ("nfc: fix refcount leak in llcp_sock_connect()") and c33b1cc62 ("nfc: fix refcount leak in llcp_sock_bind()") fixed a refcount leak bug in bind/connect but introduced a use-after-free if the same local is assigned to 2 different sockets. This can be triggered by the following simple program: int sock1 = socket( AF_NFC, SOCK_STREAM, NFC_SOCKPROTO_LLCP ); int sock2 = socket( AF_NFC, SOCK_STREAM, NFC_SOCKPROTO_LLCP ); memset( &addr, 0, sizeof(struct sockaddr_nfc_llcp) ); addr.sa_family = AF_NFC; addr.nfc_protocol = NFC_PROTO_NFC_DEP; bind( sock1, (struct sockaddr*) &addr, sizeof(struct sockaddr_nfc_llcp) ) bind( sock2, (struct sockaddr*) &addr, sizeof(struct sockaddr_nfc_llcp) ) close(sock1); close(sock2); Fix this by assigning NULL to llcp_sock->local after calling nfc_llcp_local_put. This addresses CVE-2021-23134.

In the Linux kernel, the following vulnerability has been resolved: bpf: Reject struct_ops registration that uses module ptr and the module btf_id is missing There is a UAF report in the bpf_struct_ops when CONFIG_MODULES=n. In particular, the report is on tcp_congestion_ops that has a "struct module *owner" member. For struct_ops that has a "struct module *owner" member, it can be extended either by the regular kernel module or by the bpf_struct_ops. bpf_try_module_get() will be used to do the refcounting and different refcount is done based on the owner pointer. When CONFIG_MODULES=n, the btf_id of the "struct module" is missing: WARN: resolve_btfids: unresolved symbol module Thus, the bpf_try_module_get() cannot do the correct refcounting. Not all subsystem's struct_ops requires the "struct module *owner" member. e.g. the recent sched_ext_ops. This patch is to disable bpf_struct_ops registration if the struct_ops has the "struct module *" member and the "struct module" btf_id is missing. The btf_type_is_fwd() helper is moved to the btf.h header file for this test. This has happened since the beginning of bpf_struct_ops which has gone through many changes. The Fixes tag is set to a recent commit that this patch can apply cleanly. Considering CONFIG_MODULES=n is not common and the age of the issue, targeting for bpf-next also.

In the Linux kernel, the following vulnerability has been resolved: spi: spi-zynqmp-gqspi: fix use-after-free in zynqmp_qspi_exec_op When handling op->addr, it is using the buffer "tmpbuf" which has been freed. This will trigger a use-after-free KASAN warning. Let's use temporary variables to store op->addr.val and op->cmd.opcode to fix this issue.

The do_get_mempolicy function in mm/mempolicy.c in the Linux kernel before 4.12.9 allows local users to cause a denial of service (use-after-free) or possibly have unspecified other impact via crafted system calls.

In the Linux kernel, the following vulnerability has been resolved: gfs2: Fix use-after-free in gfs2_glock_shrink_scan The GLF_LRU flag is checked under lru_lock in gfs2_glock_remove_from_lru() to remove the glock from the lru list in __gfs2_glock_put(). On the shrink scan path, the same flag is cleared under lru_lock but because of cond_resched_lock(&lru_lock) in gfs2_dispose_glock_lru(), progress on the put side can be made without deleting the glock from the lru list. Keep GLF_LRU across the race window opened by cond_resched_lock(&lru_lock) to ensure correct behavior on both sides - clear GLF_LRU after list_del under lru_lock.

In the Linux kernel, the following vulnerability has been resolved: inet: fully convert sk->sk_rx_dst to RCU rules syzbot reported various issues around early demux, one being included in this changelog [1] sk->sk_rx_dst is using RCU protection without clearly documenting it. And following sequences in tcp_v4_do_rcv()/tcp_v6_do_rcv() are not following standard RCU rules. [a] dst_release(dst); [b] sk->sk_rx_dst = NULL; They look wrong because a delete operation of RCU protected pointer is supposed to clear the pointer before the call_rcu()/synchronize_rcu() guarding actual memory freeing. In some cases indeed, dst could be freed before [b] is done. We could cheat by clearing sk_rx_dst before calling dst_release(), but this seems the right time to stick to standard RCU annotations and debugging facilities. [1] BUG: KASAN: use-after-free in dst_check include/net/dst.h:470 [inline] BUG: KASAN: use-after-free in tcp_v4_early_demux+0x95b/0x960 net/ipv4/tcp_ipv4.c:1792 Read of size 2 at addr ffff88807f1cb73a by task syz-executor.5/9204 CPU: 0 PID: 9204 Comm: syz-executor.5 Not tainted 5.16.0-rc5-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 print_address_description.constprop.0.cold+0x8d/0x320 mm/kasan/report.c:247 __kasan_report mm/kasan/report.c:433 [inline] kasan_report.cold+0x83/0xdf mm/kasan/report.c:450 dst_check include/net/dst.h:470 [inline] tcp_v4_early_demux+0x95b/0x960 net/ipv4/tcp_ipv4.c:1792 ip_rcv_finish_core.constprop.0+0x15de/0x1e80 net/ipv4/ip_input.c:340 ip_list_rcv_finish.constprop.0+0x1b2/0x6e0 net/ipv4/ip_input.c:583 ip_sublist_rcv net/ipv4/ip_input.c:609 [inline] ip_list_rcv+0x34e/0x490 net/ipv4/ip_input.c:644 __netif_receive_skb_list_ptype net/core/dev.c:5508 [inline] __netif_receive_skb_list_core+0x549/0x8e0 net/core/dev.c:5556 __netif_receive_skb_list net/core/dev.c:5608 [inline] netif_receive_skb_list_internal+0x75e/0xd80 net/core/dev.c:5699 gro_normal_list net/core/dev.c:5853 [inline] gro_normal_list net/core/dev.c:5849 [inline] napi_complete_done+0x1f1/0x880 net/core/dev.c:6590 virtqueue_napi_complete drivers/net/virtio_net.c:339 [inline] virtnet_poll+0xca2/0x11b0 drivers/net/virtio_net.c:1557 __napi_poll+0xaf/0x440 net/core/dev.c:7023 napi_poll net/core/dev.c:7090 [inline] net_rx_action+0x801/0xb40 net/core/dev.c:7177 __do_softirq+0x29b/0x9c2 kernel/softirq.c:558 invoke_softirq kernel/softirq.c:432 [inline] __irq_exit_rcu+0x123/0x180 kernel/softirq.c:637 irq_exit_rcu+0x5/0x20 kernel/softirq.c:649 common_interrupt+0x52/0xc0 arch/x86/kernel/irq.c:240 asm_common_interrupt+0x1e/0x40 arch/x86/include/asm/idtentry.h:629 RIP: 0033:0x7f5e972bfd57 Code: 39 d1 73 14 0f 1f 80 00 00 00 00 48 8b 50 f8 48 83 e8 08 48 39 ca 77 f3 48 39 c3 73 3e 48 89 13 48 8b 50 f8 48 89 38 49 8b 0e <48> 8b 3e 48 83 c3 08 48 83 c6 08 eb bc 48 39 d1 72 9e 48 39 d0 73 RSP: 002b:00007fff8a413210 EFLAGS: 00000283 RAX: 00007f5e97108990 RBX: 00007f5e97108338 RCX: ffffffff81d3aa45 RDX: ffffffff81d3aa45 RSI: 00007f5e97108340 RDI: ffffffff81d3aa45 RBP: 00007f5e97107eb8 R08: 00007f5e97108d88 R09: 0000000093c2e8d9 R10: 0000000000000000 R11: 0000000000000000 R12: 00007f5e97107eb0 R13: 00007f5e97108338 R14: 00007f5e97107ea8 R15: 0000000000000019 </TASK> Allocated by task 13: kasan_save_stack+0x1e/0x50 mm/kasan/common.c:38 kasan_set_track mm/kasan/common.c:46 [inline] set_alloc_info mm/kasan/common.c:434 [inline] __kasan_slab_alloc+0x90/0xc0 mm/kasan/common.c:467 kasan_slab_alloc include/linux/kasan.h:259 [inline] slab_post_alloc_hook mm/slab.h:519 [inline] slab_alloc_node mm/slub.c:3234 [inline] slab_alloc mm/slub.c:3242 [inline] kmem_cache_alloc+0x202/0x3a0 mm/slub.c:3247 dst_alloc+0x146/0x1f0 net/core/dst.c:92 rt_dst_alloc+0x73/0x430 net/ipv4/route.c:1613 ip_route_input_slow+0x1817/0x3a20 net/ipv4/route.c:234 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: Drivers: hv: vmbus: Use after free in __vmbus_open() The "open_info" variable is added to the &vmbus_connection.chn_msg_list, but the error handling frees "open_info" without removing it from the list. This will result in a use after free. First remove it from the list, and then free it.

In the Linux kernel, the following vulnerability has been resolved: net: ethernet: fix potential use-after-free in ec_bhf_remove static void ec_bhf_remove(struct pci_dev *dev) { ... struct ec_bhf_priv *priv = netdev_priv(net_dev); unregister_netdev(net_dev); free_netdev(net_dev); pci_iounmap(dev, priv->dma_io); pci_iounmap(dev, priv->io); ... } priv is netdev private data, but it is used after free_netdev(). It can cause use-after-free when accessing priv pointer. So, fix it by moving free_netdev() after pci_iounmap() calls.

In the Linux kernel, the following vulnerability has been resolved: net: bridge: fix vlan tunnel dst refcnt when egressing The egress tunnel code uses dst_clone() and directly sets the result which is wrong because the entry might have 0 refcnt or be already deleted, causing number of problems. It also triggers the WARN_ON() in dst_hold()[1] when a refcnt couldn't be taken. Fix it by using dst_hold_safe() and checking if a reference was actually taken before setting the dst. [1] dmesg WARN_ON log and following refcnt errors WARNING: CPU: 5 PID: 38 at include/net/dst.h:230 br_handle_egress_vlan_tunnel+0x10b/0x134 [bridge] Modules linked in: 8021q garp mrp bridge stp llc bonding ipv6 virtio_net CPU: 5 PID: 38 Comm: ksoftirqd/5 Kdump: loaded Tainted: G W 5.13.0-rc3+ #360 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33 04/01/2014 RIP: 0010:br_handle_egress_vlan_tunnel+0x10b/0x134 [bridge] Code: e8 85 bc 01 e1 45 84 f6 74 90 45 31 f6 85 db 48 c7 c7 a0 02 19 a0 41 0f 94 c6 31 c9 31 d2 44 89 f6 e8 64 bc 01 e1 85 db 75 02 <0f> 0b 31 c9 31 d2 44 89 f6 48 c7 c7 70 02 19 a0 e8 4b bc 01 e1 49 RSP: 0018:ffff8881003d39e8 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffffffffa01902a0 RBP: ffff8881040c6700 R08: 0000000000000000 R09: 0000000000000001 R10: 2ce93d0054fe0d00 R11: 54fe0d00000e0000 R12: ffff888109515000 R13: 0000000000000000 R14: 0000000000000001 R15: 0000000000000401 FS: 0000000000000000(0000) GS:ffff88822bf40000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f42ba70f030 CR3: 0000000109926000 CR4: 00000000000006e0 Call Trace: br_handle_vlan+0xbc/0xca [bridge] __br_forward+0x23/0x164 [bridge] deliver_clone+0x41/0x48 [bridge] br_handle_frame_finish+0x36f/0x3aa [bridge] ? skb_dst+0x2e/0x38 [bridge] ? br_handle_ingress_vlan_tunnel+0x3e/0x1c8 [bridge] ? br_handle_frame_finish+0x3aa/0x3aa [bridge] br_handle_frame+0x2c3/0x377 [bridge] ? __skb_pull+0x33/0x51 ? vlan_do_receive+0x4f/0x36a ? br_handle_frame_finish+0x3aa/0x3aa [bridge] __netif_receive_skb_core+0x539/0x7c6 ? __list_del_entry_valid+0x16e/0x1c2 __netif_receive_skb_list_core+0x6d/0xd6 netif_receive_skb_list_internal+0x1d9/0x1fa gro_normal_list+0x22/0x3e dev_gro_receive+0x55b/0x600 ? detach_buf_split+0x58/0x140 napi_gro_receive+0x94/0x12e virtnet_poll+0x15d/0x315 [virtio_net] __napi_poll+0x2c/0x1c9 net_rx_action+0xe6/0x1fb __do_softirq+0x115/0x2d8 run_ksoftirqd+0x18/0x20 smpboot_thread_fn+0x183/0x19c ? smpboot_unregister_percpu_thread+0x66/0x66 kthread+0x10a/0x10f ? kthread_mod_delayed_work+0xb6/0xb6 ret_from_fork+0x22/0x30 ---[ end trace 49f61b07f775fd2b ]--- dst_release: dst:00000000c02d677a refcnt:-1 dst_release underflow

In the Linux kernel, the following vulnerability has been resolved: RDMA/siw: Fix a use after free in siw_alloc_mr Our code analyzer reported a UAF. In siw_alloc_mr(), it calls siw_mr_add_mem(mr,..). In the implementation of siw_mr_add_mem(), mem is assigned to mr->mem and then mem is freed via kfree(mem) if xa_alloc_cyclic() failed. Here, mr->mem still point to a freed object. After, the execution continue up to the err_out branch of siw_alloc_mr, and the freed mr->mem is used in siw_mr_drop_mem(mr). My patch moves "mr->mem = mem" behind the if (xa_alloc_cyclic(..)<0) {} section, to avoid the uaf.

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix potential out-of-bounds memory access in nilfs_find_entry() Syzbot reported that when searching for records in a directory where the inode's i_size is corrupted and has a large value, memory access outside the folio/page range may occur, or a use-after-free bug may be detected if KASAN is enabled. This is because nilfs_last_byte(), which is called by nilfs_find_entry() and others to calculate the number of valid bytes of directory data in a page from i_size and the page index, loses the upper 32 bits of the 64-bit size information due to an inappropriate type of local variable to which the i_size value is assigned. This caused a large byte offset value due to underflow in the end address calculation in the calling nilfs_find_entry(), resulting in memory access that exceeds the folio/page size. Fix this issue by changing the type of the local variable causing the bit loss from "unsigned int" to "u64". The return value of nilfs_last_byte() is also of type "unsigned int", but it is truncated so as not to exceed PAGE_SIZE and no bit loss occurs, so no change is required.

In the Linux kernel, the following vulnerability has been resolved: ath10k: Fix a use after free in ath10k_htc_send_bundle In ath10k_htc_send_bundle, the bundle_skb could be freed by dev_kfree_skb_any(bundle_skb). But the bundle_skb is used later by bundle_skb->len. As skb_len = bundle_skb->len, my patch replaces bundle_skb->len to skb_len after the bundle_skb was freed.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix use-after-free of nreq in reqsk_timer_handler(). The cited commit replaced inet_csk_reqsk_queue_drop_and_put() with __inet_csk_reqsk_queue_drop() and reqsk_put() in reqsk_timer_handler(). Then, oreq should be passed to reqsk_put() instead of req; otherwise use-after-free of nreq could happen when reqsk is migrated but the retry attempt failed (e.g. due to timeout). Let's pass oreq to reqsk_put().

In the Linux kernel, the following vulnerability has been resolved: net: explicitly clear the sk pointer, when pf->create fails We have recently noticed the exact same KASAN splat as in commit 6cd4a78d962b ("net: do not leave a dangling sk pointer, when socket creation fails"). The problem is that commit did not fully address the problem, as some pf->create implementations do not use sk_common_release in their error paths. For example, we can use the same reproducer as in the above commit, but changing ping to arping. arping uses AF_PACKET socket and if packet_create fails, it will just sk_free the allocated sk object. While we could chase all the pf->create implementations and make sure they NULL the freed sk object on error from the socket, we can't guarantee future protocols will not make the same mistake. So it is easier to just explicitly NULL the sk pointer upon return from pf->create in __sock_create. We do know that pf->create always releases the allocated sk object on error, so if the pointer is not NULL, it is definitely dangling.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix use-after-free in SMB request handling A race condition exists between SMB request handling in `ksmbd_conn_handler_loop()` and the freeing of `ksmbd_conn` in the workqueue handler `handle_ksmbd_work()`. This leads to a UAF. - KASAN: slab-use-after-free Read in handle_ksmbd_work - KASAN: slab-use-after-free in rtlock_slowlock_locked This race condition arises as follows: - `ksmbd_conn_handler_loop()` waits for `conn->r_count` to reach zero: `wait_event(conn->r_count_q, atomic_read(&conn->r_count) == 0);` - Meanwhile, `handle_ksmbd_work()` decrements `conn->r_count` using `atomic_dec_return(&conn->r_count)`, and if it reaches zero, calls `ksmbd_conn_free()`, which frees `conn`. - However, after `handle_ksmbd_work()` decrements `conn->r_count`, it may still access `conn->r_count_q` in the following line: `waitqueue_active(&conn->r_count_q)` or `wake_up(&conn->r_count_q)` This results in a UAF, as `conn` has already been freed. The discovery of this UAF can be referenced in the following PR for syzkaller's support for SMB requests.

In the Linux kernel, the following vulnerability has been resolved: nfsd: release svc_expkey/svc_export with rcu_work The last reference for `cache_head` can be reduced to zero in `c_show` and `e_show`(using `rcu_read_lock` and `rcu_read_unlock`). Consequently, `svc_export_put` and `expkey_put` will be invoked, leading to two issues: 1. The `svc_export_put` will directly free ex_uuid. However, `e_show`/`c_show` will access `ex_uuid` after `cache_put`, which can trigger a use-after-free issue, shown below. ================================================================== BUG: KASAN: slab-use-after-free in svc_export_show+0x362/0x430 [nfsd] Read of size 1 at addr ff11000010fdc120 by task cat/870 CPU: 1 UID: 0 PID: 870 Comm: cat Not tainted 6.12.0-rc3+ #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.1-2.fc37 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x53/0x70 print_address_description.constprop.0+0x2c/0x3a0 print_report+0xb9/0x280 kasan_report+0xae/0xe0 svc_export_show+0x362/0x430 [nfsd] c_show+0x161/0x390 [sunrpc] seq_read_iter+0x589/0x770 seq_read+0x1e5/0x270 proc_reg_read+0xe1/0x140 vfs_read+0x125/0x530 ksys_read+0xc1/0x160 do_syscall_64+0x5f/0x170 entry_SYSCALL_64_after_hwframe+0x76/0x7e Allocated by task 830: kasan_save_stack+0x20/0x40 kasan_save_track+0x14/0x30 __kasan_kmalloc+0x8f/0xa0 __kmalloc_node_track_caller_noprof+0x1bc/0x400 kmemdup_noprof+0x22/0x50 svc_export_parse+0x8a9/0xb80 [nfsd] cache_do_downcall+0x71/0xa0 [sunrpc] cache_write_procfs+0x8e/0xd0 [sunrpc] proc_reg_write+0xe1/0x140 vfs_write+0x1a5/0x6d0 ksys_write+0xc1/0x160 do_syscall_64+0x5f/0x170 entry_SYSCALL_64_after_hwframe+0x76/0x7e Freed by task 868: kasan_save_stack+0x20/0x40 kasan_save_track+0x14/0x30 kasan_save_free_info+0x3b/0x60 __kasan_slab_free+0x37/0x50 kfree+0xf3/0x3e0 svc_export_put+0x87/0xb0 [nfsd] cache_purge+0x17f/0x1f0 [sunrpc] nfsd_destroy_serv+0x226/0x2d0 [nfsd] nfsd_svc+0x125/0x1e0 [nfsd] write_threads+0x16a/0x2a0 [nfsd] nfsctl_transaction_write+0x74/0xa0 [nfsd] vfs_write+0x1a5/0x6d0 ksys_write+0xc1/0x160 do_syscall_64+0x5f/0x170 entry_SYSCALL_64_after_hwframe+0x76/0x7e 2. We cannot sleep while using `rcu_read_lock`/`rcu_read_unlock`. However, `svc_export_put`/`expkey_put` will call path_put, which subsequently triggers a sleeping operation due to the following `dput`. ============================= WARNING: suspicious RCU usage 5.10.0-dirty #141 Not tainted ----------------------------- ... Call Trace: dump_stack+0x9a/0xd0 ___might_sleep+0x231/0x240 dput+0x39/0x600 path_put+0x1b/0x30 svc_export_put+0x17/0x80 e_show+0x1c9/0x200 seq_read_iter+0x63f/0x7c0 seq_read+0x226/0x2d0 vfs_read+0x113/0x2c0 ksys_read+0xc9/0x170 do_syscall_64+0x33/0x40 entry_SYSCALL_64_after_hwframe+0x67/0xd1 Fix these issues by using `rcu_work` to help release `svc_expkey`/`svc_export`. This approach allows for an asynchronous context to invoke `path_put` and also facilitates the freeing of `uuid/exp/key` after an RCU grace period.

In the Linux kernel, the following vulnerability has been resolved: fsnotify: Fix ordering of iput() and watched_objects decrement Ensure the superblock is kept alive until we're done with iput(). Holding a reference to an inode is not allowed unless we ensure the superblock stays alive, which fsnotify does by keeping the watched_objects count elevated, so iput() must happen before the watched_objects decrement. This can lead to a UAF of something like sb->s_fs_info in tmpfs, but the UAF is hard to hit because race orderings that oops are more likely, thanks to the CHECK_DATA_CORRUPTION() block in generic_shutdown_super(). Also, ensure that fsnotify_put_sb_watched_objects() doesn't call fsnotify_sb_watched_objects() on a superblock that may have already been freed, which would cause a UAF read of sb->s_fsnotify_info.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: MGMT: Fix slab-use-after-free Read in set_powered_sync This fixes the following crash: ================================================================== BUG: KASAN: slab-use-after-free in set_powered_sync+0x3a/0xc0 net/bluetooth/mgmt.c:1353 Read of size 8 at addr ffff888029b4dd18 by task kworker/u9:0/54 CPU: 1 UID: 0 PID: 54 Comm: kworker/u9:0 Not tainted 6.11.0-rc6-syzkaller-01155-gf723224742fc #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/06/2024 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> __dump_stack lib/dump_stack.c:93 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:119 print_address_description mm/kasan/report.c:377 [inline] print_report+0x169/0x550 mm/kasan/report.c:488 q kasan_report+0x143/0x180 mm/kasan/report.c:601 set_powered_sync+0x3a/0xc0 net/bluetooth/mgmt.c:1353 hci_cmd_sync_work+0x22b/0x400 net/bluetooth/hci_sync.c:328 process_one_work kernel/workqueue.c:3231 [inline] process_scheduled_works+0xa2c/0x1830 kernel/workqueue.c:3312 worker_thread+0x86d/0xd10 kernel/workqueue.c:3389 kthread+0x2f0/0x390 kernel/kthread.c:389 ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 </TASK> Allocated by task 5247: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x3f/0x80 mm/kasan/common.c:68 poison_kmalloc_redzone mm/kasan/common.c:370 [inline] __kasan_kmalloc+0x98/0xb0 mm/kasan/common.c:387 kasan_kmalloc include/linux/kasan.h:211 [inline] __kmalloc_cache_noprof+0x19c/0x2c0 mm/slub.c:4193 kmalloc_noprof include/linux/slab.h:681 [inline] kzalloc_noprof include/linux/slab.h:807 [inline] mgmt_pending_new+0x65/0x250 net/bluetooth/mgmt_util.c:269 mgmt_pending_add+0x36/0x120 net/bluetooth/mgmt_util.c:296 set_powered+0x3cd/0x5e0 net/bluetooth/mgmt.c:1394 hci_mgmt_cmd+0xc47/0x11d0 net/bluetooth/hci_sock.c:1712 hci_sock_sendmsg+0x7b8/0x11c0 net/bluetooth/hci_sock.c:1832 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x221/0x270 net/socket.c:745 sock_write_iter+0x2dd/0x400 net/socket.c:1160 new_sync_write fs/read_write.c:497 [inline] vfs_write+0xa72/0xc90 fs/read_write.c:590 ksys_write+0x1a0/0x2c0 fs/read_write.c:643 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f Freed by task 5246: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x3f/0x80 mm/kasan/common.c:68 kasan_save_free_info+0x40/0x50 mm/kasan/generic.c:579 poison_slab_object+0xe0/0x150 mm/kasan/common.c:240 __kasan_slab_free+0x37/0x60 mm/kasan/common.c:256 kasan_slab_free include/linux/kasan.h:184 [inline] slab_free_hook mm/slub.c:2256 [inline] slab_free mm/slub.c:4477 [inline] kfree+0x149/0x360 mm/slub.c:4598 settings_rsp+0x2bc/0x390 net/bluetooth/mgmt.c:1443 mgmt_pending_foreach+0xd1/0x130 net/bluetooth/mgmt_util.c:259 __mgmt_power_off+0x112/0x420 net/bluetooth/mgmt.c:9455 hci_dev_close_sync+0x665/0x11a0 net/bluetooth/hci_sync.c:5191 hci_dev_do_close net/bluetooth/hci_core.c:483 [inline] hci_dev_close+0x112/0x210 net/bluetooth/hci_core.c:508 sock_do_ioctl+0x158/0x460 net/socket.c:1222 sock_ioctl+0x629/0x8e0 net/socket.c:1341 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:907 [inline] __se_sys_ioctl+0xfc/0x170 fs/ioctl.c:893 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83gv entry_SYSCALL_64_after_hwframe+0x77/0x7f

In the Linux kernel, the following vulnerability has been resolved: ubifs: authentication: Fix use-after-free in ubifs_tnc_end_commit After an insertion in TNC, the tree might split and cause a node to change its `znode->parent`. A further deletion of other nodes in the tree (which also could free the nodes), the aforementioned node's `znode->cparent` could still point to a freed node. This `znode->cparent` may not be updated when getting nodes to commit in `ubifs_tnc_start_commit()`. This could then trigger a use-after-free when accessing the `znode->cparent` in `write_index()` in `ubifs_tnc_end_commit()`. This can be triggered by running rm -f /etc/test-file.bin dd if=/dev/urandom of=/etc/test-file.bin bs=1M count=60 conv=fsync in a loop, and with `CONFIG_UBIFS_FS_AUTHENTICATION`. KASAN then reports: BUG: KASAN: use-after-free in ubifs_tnc_end_commit+0xa5c/0x1950 Write of size 32 at addr ffffff800a3af86c by task ubifs_bgt0_20/153 Call trace: dump_backtrace+0x0/0x340 show_stack+0x18/0x24 dump_stack_lvl+0x9c/0xbc print_address_description.constprop.0+0x74/0x2b0 kasan_report+0x1d8/0x1f0 kasan_check_range+0xf8/0x1a0 memcpy+0x84/0xf4 ubifs_tnc_end_commit+0xa5c/0x1950 do_commit+0x4e0/0x1340 ubifs_bg_thread+0x234/0x2e0 kthread+0x36c/0x410 ret_from_fork+0x10/0x20 Allocated by task 401: kasan_save_stack+0x38/0x70 __kasan_kmalloc+0x8c/0xd0 __kmalloc+0x34c/0x5bc tnc_insert+0x140/0x16a4 ubifs_tnc_add+0x370/0x52c ubifs_jnl_write_data+0x5d8/0x870 do_writepage+0x36c/0x510 ubifs_writepage+0x190/0x4dc __writepage+0x58/0x154 write_cache_pages+0x394/0x830 do_writepages+0x1f0/0x5b0 filemap_fdatawrite_wbc+0x170/0x25c file_write_and_wait_range+0x140/0x190 ubifs_fsync+0xe8/0x290 vfs_fsync_range+0xc0/0x1e4 do_fsync+0x40/0x90 __arm64_sys_fsync+0x34/0x50 invoke_syscall.constprop.0+0xa8/0x260 do_el0_svc+0xc8/0x1f0 el0_svc+0x34/0x70 el0t_64_sync_handler+0x108/0x114 el0t_64_sync+0x1a4/0x1a8 Freed by task 403: kasan_save_stack+0x38/0x70 kasan_set_track+0x28/0x40 kasan_set_free_info+0x28/0x4c __kasan_slab_free+0xd4/0x13c kfree+0xc4/0x3a0 tnc_delete+0x3f4/0xe40 ubifs_tnc_remove_range+0x368/0x73c ubifs_tnc_remove_ino+0x29c/0x2e0 ubifs_jnl_delete_inode+0x150/0x260 ubifs_evict_inode+0x1d4/0x2e4 evict+0x1c8/0x450 iput+0x2a0/0x3c4 do_unlinkat+0x2cc/0x490 __arm64_sys_unlinkat+0x90/0x100 invoke_syscall.constprop.0+0xa8/0x260 do_el0_svc+0xc8/0x1f0 el0_svc+0x34/0x70 el0t_64_sync_handler+0x108/0x114 el0t_64_sync+0x1a4/0x1a8 The offending `memcpy()` in `ubifs_copy_hash()` has a use-after-free when a node becomes root in TNC but still has a `cparent` to an already freed node. More specifically, consider the following TNC: zroot / / zp1 / / zn Inserting a new node `zn_new` with a key smaller then `zn` will trigger a split in `tnc_insert()` if `zp1` is full: zroot / \ / \ zp1 zp2 / \ / \ zn_new zn `zn->parent` has now been moved to `zp2`, *but* `zn->cparent` still points to `zp1`. Now, consider a removal of all the nodes _except_ `zn`. Just when `tnc_delete()` is about to delete `zroot` and `zp2`: zroot \ \ zp2 \ \ zn `zroot` and `zp2` get freed and the tree collapses: zn `zn` now becomes the new `zroot`. `get_znodes_to_commit()` will now only find `zn`, the new `zroot`, and `write_index()` will check its `znode->cparent` that wrongly points to the already freed `zp1`. `ubifs_copy_hash()` thus gets wrongly called with `znode->cparent->zbranch[znode->iip].hash` that triggers the use-after-free! Fix this by explicitly setting `znode->cparent` to `NULL` in `get_znodes_to_commit()` for the root node. The search for the dirty nodes ---truncated---

In the Linux kernel, the following vulnerability has been resolved: HID: amd_sfh: free driver_data after destroying hid device HID driver callbacks aren't called anymore once hid_destroy_device() has been called. Hence, hid driver_data should be freed only after the hid_destroy_device() function returned as driver_data is used in several callbacks. I observed a crash with kernel 6.10.0 on my T14s Gen 3, after enabling KASAN to debug memory allocation, I got this output: [ 13.050438] ================================================================== [ 13.054060] BUG: KASAN: slab-use-after-free in amd_sfh_get_report+0x3ec/0x530 [amd_sfh] [ 13.054809] psmouse serio1: trackpoint: Synaptics TrackPoint firmware: 0x02, buttons: 3/3 [ 13.056432] Read of size 8 at addr ffff88813152f408 by task (udev-worker)/479 [ 13.060970] CPU: 5 PID: 479 Comm: (udev-worker) Not tainted 6.10.0-arch1-2 #1 893bb55d7f0073f25c46adbb49eb3785fefd74b0 [ 13.063978] Hardware name: LENOVO 21CQCTO1WW/21CQCTO1WW, BIOS R22ET70W (1.40 ) 03/21/2024 [ 13.067860] Call Trace: [ 13.069383] input: TPPS/2 Synaptics TrackPoint as /devices/platform/i8042/serio1/input/input8 [ 13.071486] <TASK> [ 13.071492] dump_stack_lvl+0x5d/0x80 [ 13.074870] snd_hda_intel 0000:33:00.6: enabling device (0000 -> 0002) [ 13.078296] ? amd_sfh_get_report+0x3ec/0x530 [amd_sfh 05f43221435b5205f734cd9da29399130f398a38] [ 13.082199] print_report+0x174/0x505 [ 13.085776] ? __pfx__raw_spin_lock_irqsave+0x10/0x10 [ 13.089367] ? srso_alias_return_thunk+0x5/0xfbef5 [ 13.093255] ? amd_sfh_get_report+0x3ec/0x530 [amd_sfh 05f43221435b5205f734cd9da29399130f398a38] [ 13.097464] kasan_report+0xc8/0x150 [ 13.101461] ? amd_sfh_get_report+0x3ec/0x530 [amd_sfh 05f43221435b5205f734cd9da29399130f398a38] [ 13.105802] amd_sfh_get_report+0x3ec/0x530 [amd_sfh 05f43221435b5205f734cd9da29399130f398a38] [ 13.110303] amdtp_hid_request+0xb8/0x110 [amd_sfh 05f43221435b5205f734cd9da29399130f398a38] [ 13.114879] ? srso_alias_return_thunk+0x5/0xfbef5 [ 13.119450] sensor_hub_get_feature+0x1d3/0x540 [hid_sensor_hub 3f13be3016ff415bea03008d45d99da837ee3082] [ 13.124097] hid_sensor_parse_common_attributes+0x4d0/0xad0 [hid_sensor_iio_common c3a5cbe93969c28b122609768bbe23efe52eb8f5] [ 13.127404] ? srso_alias_return_thunk+0x5/0xfbef5 [ 13.131925] ? __pfx_hid_sensor_parse_common_attributes+0x10/0x10 [hid_sensor_iio_common c3a5cbe93969c28b122609768bbe23efe52eb8f5] [ 13.136455] ? _raw_spin_lock_irqsave+0x96/0xf0 [ 13.140197] ? __pfx__raw_spin_lock_irqsave+0x10/0x10 [ 13.143602] ? devm_iio_device_alloc+0x34/0x50 [industrialio 3d261d5e5765625d2b052be40e526d62b1d2123b] [ 13.147234] ? srso_alias_return_thunk+0x5/0xfbef5 [ 13.150446] ? __devm_add_action+0x167/0x1d0 [ 13.155061] hid_gyro_3d_probe+0x120/0x7f0 [hid_sensor_gyro_3d 63da36a143b775846ab2dbb86c343b401b5e3172] [ 13.158581] ? srso_alias_return_thunk+0x5/0xfbef5 [ 13.161814] platform_probe+0xa2/0x150 [ 13.165029] really_probe+0x1e3/0x8a0 [ 13.168243] __driver_probe_device+0x18c/0x370 [ 13.171500] driver_probe_device+0x4a/0x120 [ 13.175000] __driver_attach+0x190/0x4a0 [ 13.178521] ? __pfx___driver_attach+0x10/0x10 [ 13.181771] bus_for_each_dev+0x106/0x180 [ 13.185033] ? __pfx__raw_spin_lock+0x10/0x10 [ 13.188229] ? __pfx_bus_for_each_dev+0x10/0x10 [ 13.191446] ? srso_alias_return_thunk+0x5/0xfbef5 [ 13.194382] bus_add_driver+0x29e/0x4d0 [ 13.197328] driver_register+0x1a5/0x360 [ 13.200283] ? __pfx_hid_gyro_3d_platform_driver_init+0x10/0x10 [hid_sensor_gyro_3d 63da36a143b775846ab2dbb86c343b401b5e3172] [ 13.203362] do_one_initcall+0xa7/0x380 [ 13.206432] ? __pfx_do_one_initcall+0x10/0x10 [ 13.210175] ? srso_alias_return_thunk+0x5/0xfbef5 [ 13.213211] ? kasan_unpoison+0x44/0x70 [ 13.216688] do_init_module+0x238/0x750 [ 13.2196 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: scsi: bfa: Fix use-after-free in bfad_im_module_exit() BUG: KASAN: slab-use-after-free in __lock_acquire+0x2aca/0x3a20 Read of size 8 at addr ffff8881082d80c8 by task modprobe/25303 Call Trace: <TASK> dump_stack_lvl+0x95/0xe0 print_report+0xcb/0x620 kasan_report+0xbd/0xf0 __lock_acquire+0x2aca/0x3a20 lock_acquire+0x19b/0x520 _raw_spin_lock+0x2b/0x40 attribute_container_unregister+0x30/0x160 fc_release_transport+0x19/0x90 [scsi_transport_fc] bfad_im_module_exit+0x23/0x60 [bfa] bfad_init+0xdb/0xff0 [bfa] do_one_initcall+0xdc/0x550 do_init_module+0x22d/0x6b0 load_module+0x4e96/0x5ff0 init_module_from_file+0xcd/0x130 idempotent_init_module+0x330/0x620 __x64_sys_finit_module+0xb3/0x110 do_syscall_64+0xc1/0x1d0 entry_SYSCALL_64_after_hwframe+0x77/0x7f </TASK> Allocated by task 25303: kasan_save_stack+0x24/0x50 kasan_save_track+0x14/0x30 __kasan_kmalloc+0x7f/0x90 fc_attach_transport+0x4f/0x4740 [scsi_transport_fc] bfad_im_module_init+0x17/0x80 [bfa] bfad_init+0x23/0xff0 [bfa] do_one_initcall+0xdc/0x550 do_init_module+0x22d/0x6b0 load_module+0x4e96/0x5ff0 init_module_from_file+0xcd/0x130 idempotent_init_module+0x330/0x620 __x64_sys_finit_module+0xb3/0x110 do_syscall_64+0xc1/0x1d0 entry_SYSCALL_64_after_hwframe+0x77/0x7f Freed by task 25303: kasan_save_stack+0x24/0x50 kasan_save_track+0x14/0x30 kasan_save_free_info+0x3b/0x60 __kasan_slab_free+0x38/0x50 kfree+0x212/0x480 bfad_im_module_init+0x7e/0x80 [bfa] bfad_init+0x23/0xff0 [bfa] do_one_initcall+0xdc/0x550 do_init_module+0x22d/0x6b0 load_module+0x4e96/0x5ff0 init_module_from_file+0xcd/0x130 idempotent_init_module+0x330/0x620 __x64_sys_finit_module+0xb3/0x110 do_syscall_64+0xc1/0x1d0 entry_SYSCALL_64_after_hwframe+0x77/0x7f Above issue happens as follows: bfad_init error = bfad_im_module_init() fc_release_transport(bfad_im_scsi_transport_template); if (error) goto ext; ext: bfad_im_module_exit(); fc_release_transport(bfad_im_scsi_transport_template); --> Trigger double release Don't call bfad_im_module_exit() if bfad_im_module_init() failed.

In the Linux kernel, the following vulnerability has been resolved: smb: prevent use-after-free due to open_cached_dir error paths If open_cached_dir() encounters an error parsing the lease from the server, the error handling may race with receiving a lease break, resulting in open_cached_dir() freeing the cfid while the queued work is pending. Update open_cached_dir() to drop refs rather than directly freeing the cfid. Have cached_dir_lease_break(), cfids_laundromat_worker(), and invalidate_all_cached_dirs() clear has_lease immediately while still holding cfids->cfid_list_lock, and then use this to also simplify the reference counting in cfids_laundromat_worker() and invalidate_all_cached_dirs(). Fixes this KASAN splat (which manually injects an error and lease break in open_cached_dir()): ================================================================== BUG: KASAN: slab-use-after-free in smb2_cached_lease_break+0x27/0xb0 Read of size 8 at addr ffff88811cc24c10 by task kworker/3:1/65 CPU: 3 UID: 0 PID: 65 Comm: kworker/3:1 Not tainted 6.12.0-rc6-g255cf264e6e5-dirty #87 Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 11/12/2020 Workqueue: cifsiod smb2_cached_lease_break Call Trace: <TASK> dump_stack_lvl+0x77/0xb0 print_report+0xce/0x660 kasan_report+0xd3/0x110 smb2_cached_lease_break+0x27/0xb0 process_one_work+0x50a/0xc50 worker_thread+0x2ba/0x530 kthread+0x17c/0x1c0 ret_from_fork+0x34/0x60 ret_from_fork_asm+0x1a/0x30 </TASK> Allocated by task 2464: kasan_save_stack+0x33/0x60 kasan_save_track+0x14/0x30 __kasan_kmalloc+0xaa/0xb0 open_cached_dir+0xa7d/0x1fb0 smb2_query_path_info+0x43c/0x6e0 cifs_get_fattr+0x346/0xf10 cifs_get_inode_info+0x157/0x210 cifs_revalidate_dentry_attr+0x2d1/0x460 cifs_getattr+0x173/0x470 vfs_statx_path+0x10f/0x160 vfs_statx+0xe9/0x150 vfs_fstatat+0x5e/0xc0 __do_sys_newfstatat+0x91/0xf0 do_syscall_64+0x95/0x1a0 entry_SYSCALL_64_after_hwframe+0x76/0x7e Freed by task 2464: kasan_save_stack+0x33/0x60 kasan_save_track+0x14/0x30 kasan_save_free_info+0x3b/0x60 __kasan_slab_free+0x51/0x70 kfree+0x174/0x520 open_cached_dir+0x97f/0x1fb0 smb2_query_path_info+0x43c/0x6e0 cifs_get_fattr+0x346/0xf10 cifs_get_inode_info+0x157/0x210 cifs_revalidate_dentry_attr+0x2d1/0x460 cifs_getattr+0x173/0x470 vfs_statx_path+0x10f/0x160 vfs_statx+0xe9/0x150 vfs_fstatat+0x5e/0xc0 __do_sys_newfstatat+0x91/0xf0 do_syscall_64+0x95/0x1a0 entry_SYSCALL_64_after_hwframe+0x76/0x7e Last potentially related work creation: kasan_save_stack+0x33/0x60 __kasan_record_aux_stack+0xad/0xc0 insert_work+0x32/0x100 __queue_work+0x5c9/0x870 queue_work_on+0x82/0x90 open_cached_dir+0x1369/0x1fb0 smb2_query_path_info+0x43c/0x6e0 cifs_get_fattr+0x346/0xf10 cifs_get_inode_info+0x157/0x210 cifs_revalidate_dentry_attr+0x2d1/0x460 cifs_getattr+0x173/0x470 vfs_statx_path+0x10f/0x160 vfs_statx+0xe9/0x150 vfs_fstatat+0x5e/0xc0 __do_sys_newfstatat+0x91/0xf0 do_syscall_64+0x95/0x1a0 entry_SYSCALL_64_after_hwframe+0x76/0x7e The buggy address belongs to the object at ffff88811cc24c00 which belongs to the cache kmalloc-1k of size 1024 The buggy address is located 16 bytes inside of freed 1024-byte region [ffff88811cc24c00, ffff88811cc25000)

In the Linux kernel, the following vulnerability has been resolved: iommu/s390: Implement blocking domain This fixes a crash when surprise hot-unplugging a PCI device. This crash happens because during hot-unplug __iommu_group_set_domain_nofail() attaching the default domain fails when the platform no longer recognizes the device as it has already been removed and we end up with a NULL domain pointer and UAF. This is exactly the case referred to in the second comment in __iommu_device_set_domain() and just as stated there if we can instead attach the blocking domain the UAF is prevented as this can handle the already removed device. Implement the blocking domain to use this handling. With this change, the crash is fixed but we still hit a warning attempting to change DMA ownership on a blocked device.

In the Linux kernel, the following vulnerability has been resolved: PCI: Fix use-after-free of slot->bus on hot remove Dennis reports a boot crash on recent Lenovo laptops with a USB4 dock. Since commit 0fc70886569c ("thunderbolt: Reset USB4 v2 host router") and commit 59a54c5f3dbd ("thunderbolt: Reset topology created by the boot firmware"), USB4 v2 and v1 Host Routers are reset on probe of the thunderbolt driver. The reset clears the Presence Detect State and Data Link Layer Link Active bits at the USB4 Host Router's Root Port and thus causes hot removal of the dock. The crash occurs when pciehp is unbound from one of the dock's Downstream Ports: pciehp creates a pci_slot on bind and destroys it on unbind. The pci_slot contains a pointer to the pci_bus below the Downstream Port, but a reference on that pci_bus is never acquired. The pci_bus is destroyed before the pci_slot, so a use-after-free ensues when pci_slot_release() accesses slot->bus. In principle this should not happen because pci_stop_bus_device() unbinds pciehp (and therefore destroys the pci_slot) before the pci_bus is destroyed by pci_remove_bus_device(). However the stacktrace provided by Dennis shows that pciehp is unbound from pci_remove_bus_device() instead of pci_stop_bus_device(). To understand the significance of this, one needs to know that the PCI core uses a two step process to remove a portion of the hierarchy: It first unbinds all drivers in the sub-hierarchy in pci_stop_bus_device() and then actually removes the devices in pci_remove_bus_device(). There is no precaution to prevent driver binding in-between pci_stop_bus_device() and pci_remove_bus_device(). In Dennis' case, it seems removal of the hierarchy by pciehp races with driver binding by pci_bus_add_devices(). pciehp is bound to the Downstream Port after pci_stop_bus_device() has run, so it is unbound by pci_remove_bus_device() instead of pci_stop_bus_device(). Because the pci_bus has already been destroyed at that point, accesses to it result in a use-after-free. One might conclude that driver binding needs to be prevented after pci_stop_bus_device() has run. However it seems risky that pci_slot points to pci_bus without holding a reference. Solely relying on correct ordering of driver unbind versus pci_bus destruction is certainly not defensive programming. If pci_slot has a need to access data in pci_bus, it ought to acquire a reference. Amend pci_create_slot() accordingly. Dennis reports that the crash is not reproducible with this change. Abridged stacktrace: pcieport 0000:00:07.0: PME: Signaling with IRQ 156 pcieport 0000:00:07.0: pciehp: Slot #12 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Interlock- NoCompl+ IbPresDis- LLActRep+ pci_bus 0000:20: dev 00, created physical slot 12 pcieport 0000:00:07.0: pciehp: Slot(12): Card not present ... pcieport 0000:21:02.0: pciehp: pcie_disable_notification: SLOTCTRL d8 write cmd 0 Oops: general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6b6b: 0000 [#1] PREEMPT SMP NOPTI CPU: 13 UID: 0 PID: 134 Comm: irq/156-pciehp Not tainted 6.11.0-devel+ #1 RIP: 0010:dev_driver_string+0x12/0x40 pci_destroy_slot pciehp_remove pcie_port_remove_service device_release_driver_internal bus_remove_device device_del device_unregister remove_iter device_for_each_child pcie_portdrv_remove pci_device_remove device_release_driver_internal bus_remove_device device_del pci_remove_bus_device (recursive invocation) pci_remove_bus_device pciehp_unconfigure_device pciehp_disable_slot pciehp_handle_presence_or_link_change pciehp_ist

In the Linux kernel, the following vulnerability has been resolved: ALSA: 6fire: Release resources at card release The current 6fire code tries to release the resources right after the call of usb6fire_chip_abort(). But at this moment, the card object might be still in use (as we're calling snd_card_free_when_closed()). For avoid potential UAFs, move the release of resources to the card's private_free instead of the manual call of usb6fire_chip_destroy() at the USB disconnect callback.

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix use-after-free of signing key Customers have reported use-after-free in @ses->auth_key.response with SMB2.1 + sign mounts which occurs due to following race: task A task B cifs_mount() dfs_mount_share() get_session() cifs_mount_get_session() cifs_send_recv() cifs_get_smb_ses() compound_send_recv() cifs_setup_session() smb2_setup_request() kfree_sensitive() smb2_calc_signature() crypto_shash_setkey() *UAF* Fix this by ensuring that we have a valid @ses->auth_key.response by checking whether @ses->ses_status is SES_GOOD or SES_EXITING with @ses->ses_lock held. After commit 24a9799aa8ef ("smb: client: fix UAF in smb2_reconnect_server()"), we made sure to call ->logoff() only when @ses was known to be good (e.g. valid ->auth_key.response), so it's safe to access signing key when @ses->ses_status == SES_EXITING.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix race in concurrent f2fs_stop_gc_thread In my test case, concurrent calls to f2fs shutdown report the following stack trace: Oops: general protection fault, probably for non-canonical address 0xc6cfff63bb5513fc: 0000 [#1] PREEMPT SMP PTI CPU: 0 UID: 0 PID: 678 Comm: f2fs_rep_shutdo Not tainted 6.12.0-rc5-next-20241029-g6fb2fa9805c5-dirty #85 Call Trace: <TASK> ? show_regs+0x8b/0xa0 ? __die_body+0x26/0xa0 ? die_addr+0x54/0x90 ? exc_general_protection+0x24b/0x5c0 ? asm_exc_general_protection+0x26/0x30 ? kthread_stop+0x46/0x390 f2fs_stop_gc_thread+0x6c/0x110 f2fs_do_shutdown+0x309/0x3a0 f2fs_ioc_shutdown+0x150/0x1c0 __f2fs_ioctl+0xffd/0x2ac0 f2fs_ioctl+0x76/0xe0 vfs_ioctl+0x23/0x60 __x64_sys_ioctl+0xce/0xf0 x64_sys_call+0x2b1b/0x4540 do_syscall_64+0xa7/0x240 entry_SYSCALL_64_after_hwframe+0x76/0x7e The root cause is a race condition in f2fs_stop_gc_thread() called from different f2fs shutdown paths: [CPU0] [CPU1] ---------------------- ----------------------- f2fs_stop_gc_thread f2fs_stop_gc_thread gc_th = sbi->gc_thread gc_th = sbi->gc_thread kfree(gc_th) sbi->gc_thread = NULL < gc_th != NULL > kthread_stop(gc_th->f2fs_gc_task) //UAF The commit c7f114d864ac ("f2fs: fix to avoid use-after-free in f2fs_stop_gc_thread()") attempted to fix this issue by using a read semaphore to prevent races between shutdown and remount threads, but it fails to prevent all race conditions. Fix it by converting to write lock of s_umount in f2fs_do_shutdown().

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: fix use-after-free in device_for_each_child() Syzbot has reported the following KASAN splat: BUG: KASAN: slab-use-after-free in device_for_each_child+0x18f/0x1a0 Read of size 8 at addr ffff88801f605308 by task kbnepd bnep0/4980 CPU: 0 UID: 0 PID: 4980 Comm: kbnepd bnep0 Not tainted 6.12.0-rc4-00161-gae90f6a6170d #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x100/0x190 ? device_for_each_child+0x18f/0x1a0 print_report+0x13a/0x4cb ? __virt_addr_valid+0x5e/0x590 ? __phys_addr+0xc6/0x150 ? device_for_each_child+0x18f/0x1a0 kasan_report+0xda/0x110 ? device_for_each_child+0x18f/0x1a0 ? __pfx_dev_memalloc_noio+0x10/0x10 device_for_each_child+0x18f/0x1a0 ? __pfx_device_for_each_child+0x10/0x10 pm_runtime_set_memalloc_noio+0xf2/0x180 netdev_unregister_kobject+0x1ed/0x270 unregister_netdevice_many_notify+0x123c/0x1d80 ? __mutex_trylock_common+0xde/0x250 ? __pfx_unregister_netdevice_many_notify+0x10/0x10 ? trace_contention_end+0xe6/0x140 ? __mutex_lock+0x4e7/0x8f0 ? __pfx_lock_acquire.part.0+0x10/0x10 ? rcu_is_watching+0x12/0xc0 ? unregister_netdev+0x12/0x30 unregister_netdevice_queue+0x30d/0x3f0 ? __pfx_unregister_netdevice_queue+0x10/0x10 ? __pfx_down_write+0x10/0x10 unregister_netdev+0x1c/0x30 bnep_session+0x1fb3/0x2ab0 ? __pfx_bnep_session+0x10/0x10 ? __pfx_lock_release+0x10/0x10 ? __pfx_woken_wake_function+0x10/0x10 ? __kthread_parkme+0x132/0x200 ? __pfx_bnep_session+0x10/0x10 ? kthread+0x13a/0x370 ? __pfx_bnep_session+0x10/0x10 kthread+0x2b7/0x370 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x48/0x80 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> Allocated by task 4974: kasan_save_stack+0x30/0x50 kasan_save_track+0x14/0x30 __kasan_kmalloc+0xaa/0xb0 __kmalloc_noprof+0x1d1/0x440 hci_alloc_dev_priv+0x1d/0x2820 __vhci_create_device+0xef/0x7d0 vhci_write+0x2c7/0x480 vfs_write+0x6a0/0xfc0 ksys_write+0x12f/0x260 do_syscall_64+0xc7/0x250 entry_SYSCALL_64_after_hwframe+0x77/0x7f Freed by task 4979: kasan_save_stack+0x30/0x50 kasan_save_track+0x14/0x30 kasan_save_free_info+0x3b/0x60 __kasan_slab_free+0x4f/0x70 kfree+0x141/0x490 hci_release_dev+0x4d9/0x600 bt_host_release+0x6a/0xb0 device_release+0xa4/0x240 kobject_put+0x1ec/0x5a0 put_device+0x1f/0x30 vhci_release+0x81/0xf0 __fput+0x3f6/0xb30 task_work_run+0x151/0x250 do_exit+0xa79/0x2c30 do_group_exit+0xd5/0x2a0 get_signal+0x1fcd/0x2210 arch_do_signal_or_restart+0x93/0x780 syscall_exit_to_user_mode+0x140/0x290 do_syscall_64+0xd4/0x250 entry_SYSCALL_64_after_hwframe+0x77/0x7f In 'hci_conn_del_sysfs()', 'device_unregister()' may be called when an underlying (kobject) reference counter is greater than 1. This means that reparenting (happened when the device is actually freed) is delayed and, during that delay, parent controller device (hciX) may be deleted. Since the latter may create a dangling pointer to freed parent, avoid that scenario by reparenting to NULL explicitly.