In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix slab-use-after-free in smb3_preauth_hash_rsp ksmbd_user_session_put should be called under smb3_preauth_hash_rsp(). It will avoid freeing session before calling smb3_preauth_hash_rsp().

In the Linux kernel, the following vulnerability has been resolved: netfilter: Fix use-after-free in get_info() ip6table_nat module unload has refcnt warning for UAF. call trace is: WARNING: CPU: 1 PID: 379 at kernel/module/main.c:853 module_put+0x6f/0x80 Modules linked in: ip6table_nat(-) CPU: 1 UID: 0 PID: 379 Comm: ip6tables Not tainted 6.12.0-rc4-00047-gc2ee9f594da8-dirty #205 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 RIP: 0010:module_put+0x6f/0x80 Call Trace: <TASK> get_info+0x128/0x180 do_ip6t_get_ctl+0x6a/0x430 nf_getsockopt+0x46/0x80 ipv6_getsockopt+0xb9/0x100 rawv6_getsockopt+0x42/0x190 do_sock_getsockopt+0xaa/0x180 __sys_getsockopt+0x70/0xc0 __x64_sys_getsockopt+0x20/0x30 do_syscall_64+0xa2/0x1a0 entry_SYSCALL_64_after_hwframe+0x77/0x7f Concurrent execution of module unload and get_info() trigered the warning. The root cause is as follows: cpu0 cpu1 module_exit //mod->state = MODULE_STATE_GOING ip6table_nat_exit xt_unregister_template kfree(t) //removed from templ_list getinfo() t = xt_find_table_lock list_for_each_entry(tmpl, &xt_templates[af]...) if (strcmp(tmpl->name, name)) continue; //table not found try_module_get list_for_each_entry(t, &xt_net->tables[af]...) return t; //not get refcnt module_put(t->me) //uaf unregister_pernet_subsys //remove table from xt_net list While xt_table module was going away and has been removed from xt_templates list, we couldnt get refcnt of xt_table->me. Check module in xt_net->tables list re-traversal to fix it.

In the Linux kernel, the following vulnerability has been resolved: net: sched: use RCU read-side critical section in taprio_dump() Fix possible use-after-free in 'taprio_dump()' by adding RCU read-side critical section there. Never seen on x86 but found on a KASAN-enabled arm64 system when investigating https://syzkaller.appspot.com/bug?extid=b65e0af58423fc8a73aa: [T15862] BUG: KASAN: slab-use-after-free in taprio_dump+0xa0c/0xbb0 [T15862] Read of size 4 at addr ffff0000d4bb88f8 by task repro/15862 [T15862] [T15862] CPU: 0 UID: 0 PID: 15862 Comm: repro Not tainted 6.11.0-rc1-00293-gdefaf1a2113a-dirty #2 [T15862] Hardware name: QEMU QEMU Virtual Machine, BIOS edk2-20240524-5.fc40 05/24/2024 [T15862] Call trace: [T15862] dump_backtrace+0x20c/0x220 [T15862] show_stack+0x2c/0x40 [T15862] dump_stack_lvl+0xf8/0x174 [T15862] print_report+0x170/0x4d8 [T15862] kasan_report+0xb8/0x1d4 [T15862] __asan_report_load4_noabort+0x20/0x2c [T15862] taprio_dump+0xa0c/0xbb0 [T15862] tc_fill_qdisc+0x540/0x1020 [T15862] qdisc_notify.isra.0+0x330/0x3a0 [T15862] tc_modify_qdisc+0x7b8/0x1838 [T15862] rtnetlink_rcv_msg+0x3c8/0xc20 [T15862] netlink_rcv_skb+0x1f8/0x3d4 [T15862] rtnetlink_rcv+0x28/0x40 [T15862] netlink_unicast+0x51c/0x790 [T15862] netlink_sendmsg+0x79c/0xc20 [T15862] __sock_sendmsg+0xe0/0x1a0 [T15862] ____sys_sendmsg+0x6c0/0x840 [T15862] ___sys_sendmsg+0x1ac/0x1f0 [T15862] __sys_sendmsg+0x110/0x1d0 [T15862] __arm64_sys_sendmsg+0x74/0xb0 [T15862] invoke_syscall+0x88/0x2e0 [T15862] el0_svc_common.constprop.0+0xe4/0x2a0 [T15862] do_el0_svc+0x44/0x60 [T15862] el0_svc+0x50/0x184 [T15862] el0t_64_sync_handler+0x120/0x12c [T15862] el0t_64_sync+0x190/0x194 [T15862] [T15862] Allocated by task 15857: [T15862] kasan_save_stack+0x3c/0x70 [T15862] kasan_save_track+0x20/0x3c [T15862] kasan_save_alloc_info+0x40/0x60 [T15862] __kasan_kmalloc+0xd4/0xe0 [T15862] __kmalloc_cache_noprof+0x194/0x334 [T15862] taprio_change+0x45c/0x2fe0 [T15862] tc_modify_qdisc+0x6a8/0x1838 [T15862] rtnetlink_rcv_msg+0x3c8/0xc20 [T15862] netlink_rcv_skb+0x1f8/0x3d4 [T15862] rtnetlink_rcv+0x28/0x40 [T15862] netlink_unicast+0x51c/0x790 [T15862] netlink_sendmsg+0x79c/0xc20 [T15862] __sock_sendmsg+0xe0/0x1a0 [T15862] ____sys_sendmsg+0x6c0/0x840 [T15862] ___sys_sendmsg+0x1ac/0x1f0 [T15862] __sys_sendmsg+0x110/0x1d0 [T15862] __arm64_sys_sendmsg+0x74/0xb0 [T15862] invoke_syscall+0x88/0x2e0 [T15862] el0_svc_common.constprop.0+0xe4/0x2a0 [T15862] do_el0_svc+0x44/0x60 [T15862] el0_svc+0x50/0x184 [T15862] el0t_64_sync_handler+0x120/0x12c [T15862] el0t_64_sync+0x190/0x194 [T15862] [T15862] Freed by task 6192: [T15862] kasan_save_stack+0x3c/0x70 [T15862] kasan_save_track+0x20/0x3c [T15862] kasan_save_free_info+0x4c/0x80 [T15862] poison_slab_object+0x110/0x160 [T15862] __kasan_slab_free+0x3c/0x74 [T15862] kfree+0x134/0x3c0 [T15862] taprio_free_sched_cb+0x18c/0x220 [T15862] rcu_core+0x920/0x1b7c [T15862] rcu_core_si+0x10/0x1c [T15862] handle_softirqs+0x2e8/0xd64 [T15862] __do_softirq+0x14/0x20

In the Linux kernel, the following vulnerability has been resolved: drm/amd/pm: Vangogh: Fix kernel memory out of bounds write KASAN reports that the GPU metrics table allocated in vangogh_tables_init() is not large enough for the memset done in smu_cmn_init_soft_gpu_metrics(). Condensed report follows: [ 33.861314] BUG: KASAN: slab-out-of-bounds in smu_cmn_init_soft_gpu_metrics+0x73/0x200 [amdgpu] [ 33.861799] Write of size 168 at addr ffff888129f59500 by task mangoapp/1067 ... [ 33.861808] CPU: 6 UID: 1000 PID: 1067 Comm: mangoapp Tainted: G W 6.12.0-rc4 #356 1a56f59a8b5182eeaf67eb7cb8b13594dd23b544 [ 33.861816] Tainted: [W]=WARN [ 33.861818] Hardware name: Valve Galileo/Galileo, BIOS F7G0107 12/01/2023 [ 33.861822] Call Trace: [ 33.861826] <TASK> [ 33.861829] dump_stack_lvl+0x66/0x90 [ 33.861838] print_report+0xce/0x620 [ 33.861853] kasan_report+0xda/0x110 [ 33.862794] kasan_check_range+0xfd/0x1a0 [ 33.862799] __asan_memset+0x23/0x40 [ 33.862803] smu_cmn_init_soft_gpu_metrics+0x73/0x200 [amdgpu 13b1bc364ec578808f676eba412c20eaab792779] [ 33.863306] vangogh_get_gpu_metrics_v2_4+0x123/0xad0 [amdgpu 13b1bc364ec578808f676eba412c20eaab792779] [ 33.864257] vangogh_common_get_gpu_metrics+0xb0c/0xbc0 [amdgpu 13b1bc364ec578808f676eba412c20eaab792779] [ 33.865682] amdgpu_dpm_get_gpu_metrics+0xcc/0x110 [amdgpu 13b1bc364ec578808f676eba412c20eaab792779] [ 33.866160] amdgpu_get_gpu_metrics+0x154/0x2d0 [amdgpu 13b1bc364ec578808f676eba412c20eaab792779] [ 33.867135] dev_attr_show+0x43/0xc0 [ 33.867147] sysfs_kf_seq_show+0x1f1/0x3b0 [ 33.867155] seq_read_iter+0x3f8/0x1140 [ 33.867173] vfs_read+0x76c/0xc50 [ 33.867198] ksys_read+0xfb/0x1d0 [ 33.867214] do_syscall_64+0x90/0x160 ... [ 33.867353] Allocated by task 378 on cpu 7 at 22.794876s: [ 33.867358] kasan_save_stack+0x33/0x50 [ 33.867364] kasan_save_track+0x17/0x60 [ 33.867367] __kasan_kmalloc+0x87/0x90 [ 33.867371] vangogh_init_smc_tables+0x3f9/0x840 [amdgpu] [ 33.867835] smu_sw_init+0xa32/0x1850 [amdgpu] [ 33.868299] amdgpu_device_init+0x467b/0x8d90 [amdgpu] [ 33.868733] amdgpu_driver_load_kms+0x19/0xf0 [amdgpu] [ 33.869167] amdgpu_pci_probe+0x2d6/0xcd0 [amdgpu] [ 33.869608] local_pci_probe+0xda/0x180 [ 33.869614] pci_device_probe+0x43f/0x6b0 Empirically we can confirm that the former allocates 152 bytes for the table, while the latter memsets the 168 large block. Root cause appears that when GPU metrics tables for v2_4 parts were added it was not considered to enlarge the table to fit. The fix in this patch is rather "brute force" and perhaps later should be done in a smarter way, by extracting and consolidating the part version to size logic to a common helper, instead of brute forcing the largest possible allocation. Nevertheless, for now this works and fixes the out of bounds write. v2: * Drop impossible v3_0 case. (Mario) (cherry picked from commit 0880f58f9609f0200483a49429af0f050d281703)

In the Linux kernel, the following vulnerability has been resolved: block, bfq: fix uaf for accessing waker_bfqq after splitting After commit 42c306ed7233 ("block, bfq: don't break merge chain in bfq_split_bfqq()"), if the current procress is the last holder of bfqq, the bfqq can be freed after bfq_split_bfqq(). Hence recored the bfqq and then access bfqq->waker_bfqq may trigger UAF. What's more, the waker_bfqq may in the merge chain of bfqq, hence just recored waker_bfqq is still not safe. Fix the problem by adding a helper bfq_waker_bfqq() to check if bfqq->waker_bfqq is in the merge chain, and current procress is the only holder.

In the Linux kernel, the following vulnerability has been resolved: spi: mpc52xx: Add cancel_work_sync before module remove If we remove the module which will call mpc52xx_spi_remove it will free 'ms' through spi_unregister_controller. while the work ms->work will be used. The sequence of operations that may lead to a UAF bug. Fix it by ensuring that the work is canceled before proceeding with the cleanup in mpc52xx_spi_remove.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix slab-use-after-free in ksmbd_smb2_session_create There is a race condition between ksmbd_smb2_session_create and ksmbd_expire_session. This patch add missing sessions_table_lock while adding/deleting session from global session table.

In the Linux kernel, the following vulnerability has been resolved: ext4: avoid use-after-free in ext4_ext_show_leaf() In ext4_find_extent(), path may be freed by error or be reallocated, so using a previously saved *ppath may have been freed and thus may trigger use-after-free, as follows: ext4_split_extent path = *ppath; ext4_split_extent_at(ppath) path = ext4_find_extent(ppath) ext4_split_extent_at(ppath) // ext4_find_extent fails to free path // but zeroout succeeds ext4_ext_show_leaf(inode, path) eh = path[depth].p_hdr // path use-after-free !!! Similar to ext4_split_extent_at(), we use *ppath directly as an input to ext4_ext_show_leaf(). Fix a spelling error by the way. Same problem in ext4_ext_handle_unwritten_extents(). Since 'path' is only used in ext4_ext_show_leaf(), remove 'path' and use *ppath directly. This issue is triggered only when EXT_DEBUG is defined and therefore does not affect functionality.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix user-after-free from session log off There is racy issue between smb2 session log off and smb2 session setup. It will cause user-after-free from session log off. This add session_lock when setting SMB2_SESSION_EXPIRED and referece count to session struct not to free session while it is being used.

In the Linux kernel, the following vulnerability has been resolved: bpf, arm64: Fix address emission with tag-based KASAN enabled When BPF_TRAMP_F_CALL_ORIG is enabled, the address of a bpf_tramp_image struct on the stack is passed during the size calculation pass and an address on the heap is passed during code generation. This may cause a heap buffer overflow if the heap address is tagged because emit_a64_mov_i64() will emit longer code than it did during the size calculation pass. The same problem could occur without tag-based KASAN if one of the 16-bit words of the stack address happened to be all-ones during the size calculation pass. Fix the problem by assuming the worst case (4 instructions) when calculating the size of the bpf_tramp_image address emission.

Integer overflow in the vc4_get_bcl function in drivers/gpu/drm/vc4/vc4_gem.c in the VideoCore DRM driver in the Linux kernel before 4.9.7 allows local users to cause a denial of service or possibly have unspecified other impact via a crafted size value in a VC4_SUBMIT_CL ioctl call.

In the Linux kernel, the following vulnerability has been resolved: cifs: Fix buffer overflow when parsing NFS reparse points ReparseDataLength is sum of the InodeType size and DataBuffer size. So to get DataBuffer size it is needed to subtract InodeType's size from ReparseDataLength. Function cifs_strndup_from_utf16() is currentlly accessing buf->DataBuffer at position after the end of the buffer because it does not subtract InodeType size from the length. Fix this problem and correctly subtract variable len. Member InodeType is present only when reparse buffer is large enough. Check for ReparseDataLength before accessing InodeType to prevent another invalid memory access. Major and minor rdev values are present also only when reparse buffer is large enough. Check for reparse buffer size before calling reparse_mkdev().

In the Linux kernel, the following vulnerability has been resolved: uprobe: avoid out-of-bounds memory access of fetching args Uprobe needs to fetch args into a percpu buffer, and then copy to ring buffer to avoid non-atomic context problem. Sometimes user-space strings, arrays can be very large, but the size of percpu buffer is only page size. And store_trace_args() won't check whether these data exceeds a single page or not, caused out-of-bounds memory access. It could be reproduced by following steps: 1. build kernel with CONFIG_KASAN enabled 2. save follow program as test.c ``` \#include <stdio.h> \#include <stdlib.h> \#include <string.h> // If string length large than MAX_STRING_SIZE, the fetch_store_strlen() // will return 0, cause __get_data_size() return shorter size, and // store_trace_args() will not trigger out-of-bounds access. // So make string length less than 4096. \#define STRLEN 4093 void generate_string(char *str, int n) { int i; for (i = 0; i < n; ++i) { char c = i % 26 + 'a'; str[i] = c; } str[n-1] = '\0'; } void print_string(char *str) { printf("%s\n", str); } int main() { char tmp[STRLEN]; generate_string(tmp, STRLEN); print_string(tmp); return 0; } ``` 3. compile program `gcc -o test test.c` 4. get the offset of `print_string()` ``` objdump -t test | grep -w print_string 0000000000401199 g F .text 000000000000001b print_string ``` 5. configure uprobe with offset 0x1199 ``` off=0x1199 cd /sys/kernel/debug/tracing/ echo "p /root/test:${off} arg1=+0(%di):ustring arg2=\$comm arg3=+0(%di):ustring" > uprobe_events echo 1 > events/uprobes/enable echo 1 > tracing_on ``` 6. run `test`, and kasan will report error. ================================================================== BUG: KASAN: use-after-free in strncpy_from_user+0x1d6/0x1f0 Write of size 8 at addr ffff88812311c004 by task test/499CPU: 0 UID: 0 PID: 499 Comm: test Not tainted 6.12.0-rc3+ #18 Hardware name: Red Hat KVM, BIOS 1.16.0-4.al8 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x55/0x70 print_address_description.constprop.0+0x27/0x310 kasan_report+0x10f/0x120 ? strncpy_from_user+0x1d6/0x1f0 strncpy_from_user+0x1d6/0x1f0 ? rmqueue.constprop.0+0x70d/0x2ad0 process_fetch_insn+0xb26/0x1470 ? __pfx_process_fetch_insn+0x10/0x10 ? _raw_spin_lock+0x85/0xe0 ? __pfx__raw_spin_lock+0x10/0x10 ? __pte_offset_map+0x1f/0x2d0 ? unwind_next_frame+0xc5f/0x1f80 ? arch_stack_walk+0x68/0xf0 ? is_bpf_text_address+0x23/0x30 ? kernel_text_address.part.0+0xbb/0xd0 ? __kernel_text_address+0x66/0xb0 ? unwind_get_return_address+0x5e/0xa0 ? __pfx_stack_trace_consume_entry+0x10/0x10 ? arch_stack_walk+0xa2/0xf0 ? _raw_spin_lock_irqsave+0x8b/0xf0 ? __pfx__raw_spin_lock_irqsave+0x10/0x10 ? depot_alloc_stack+0x4c/0x1f0 ? _raw_spin_unlock_irqrestore+0xe/0x30 ? stack_depot_save_flags+0x35d/0x4f0 ? kasan_save_stack+0x34/0x50 ? kasan_save_stack+0x24/0x50 ? mutex_lock+0x91/0xe0 ? __pfx_mutex_lock+0x10/0x10 prepare_uprobe_buffer.part.0+0x2cd/0x500 uprobe_dispatcher+0x2c3/0x6a0 ? __pfx_uprobe_dispatcher+0x10/0x10 ? __kasan_slab_alloc+0x4d/0x90 handler_chain+0xdd/0x3e0 handle_swbp+0x26e/0x3d0 ? __pfx_handle_swbp+0x10/0x10 ? uprobe_pre_sstep_notifier+0x151/0x1b0 irqentry_exit_to_user_mode+0xe2/0x1b0 asm_exc_int3+0x39/0x40 RIP: 0033:0x401199 Code: 01 c2 0f b6 45 fb 88 02 83 45 fc 01 8b 45 fc 3b 45 e4 7c b7 8b 45 e4 48 98 48 8d 50 ff 48 8b 45 e8 48 01 d0 ce RSP: 002b:00007ffdf00576a8 EFLAGS: 00000206 RAX: 00007ffdf00576b0 RBX: 0000000000000000 RCX: 0000000000000ff2 RDX: 0000000000000ffc RSI: 0000000000000ffd RDI: 00007ffdf00576b0 RBP: 00007ffdf00586b0 R08: 00007feb2f9c0d20 R09: 00007feb2f9c0d20 R10: 0000000000000001 R11: 0000000000000202 R12: 0000000000401040 R13: 00007ffdf0058780 R14: 0000000000000000 R15: 0000000000000000 </TASK> This commit enforces the buffer's maxlen less than a page-size to avoid store_trace_args() out-of-memory access.

In the Linux kernel, the following vulnerability has been resolved: net/xen-netback: prevent UAF in xenvif_flush_hash() During the list_for_each_entry_rcu iteration call of xenvif_flush_hash, kfree_rcu does not exist inside the rcu read critical section, so if kfree_rcu is called when the rcu grace period ends during the iteration, UAF occurs when accessing head->next after the entry becomes free. Therefore, to solve this, you need to change it to list_for_each_entry_safe.

An issue was discovered in these Pivotal RabbitMQ versions: all 3.4.x versions, all 3.5.x versions, and 3.6.x versions prior to 3.6.9; and these RabbitMQ for PCF versions: all 1.5.x versions, 1.6.x versions prior to 1.6.18, and 1.7.x versions prior to 1.7.15. RabbitMQ management UI stores signed-in user credentials in a browser's local storage without expiration, making it possible to retrieve them using a chained attack.

In the Linux kernel, the following vulnerability has been resolved: fbdev: pxafb: Fix possible use after free in pxafb_task() In the pxafb_probe function, it calls the pxafb_init_fbinfo function, after which &fbi->task is associated with pxafb_task. Moreover, within this pxafb_init_fbinfo function, the pxafb_blank function within the &pxafb_ops struct is capable of scheduling work. If we remove the module which will call pxafb_remove to make cleanup, it will call unregister_framebuffer function which can call do_unregister_framebuffer to free fbi->fb through put_fb_info(fb_info), while the work mentioned above will be used. The sequence of operations that may lead to a UAF bug is as follows: CPU0 CPU1 | pxafb_task pxafb_remove | unregister_framebuffer(info) | do_unregister_framebuffer(fb_info) | put_fb_info(fb_info) | // free fbi->fb | set_ctrlr_state(fbi, state) | __pxafb_lcd_power(fbi, 0) | fbi->lcd_power(on, &fbi->fb.var) | //use fbi->fb Fix it by ensuring that the work is canceled before proceeding with the cleanup in pxafb_remove. Note that only root user can remove the driver at runtime.

In the Linux kernel, the following vulnerability has been resolved: drm/xe/tracing: Fix a potential TP_printk UAF The commit afd2627f727b ("tracing: Check "%s" dereference via the field and not the TP_printk format") exposes potential UAFs in the xe_bo_move trace event. Fix those by avoiding dereferencing the xe_mem_type_to_name[] array at TP_printk time. Since some code refactoring has taken place, explicit backporting may be needed for kernels older than 6.10.

The do_shmat function in ipc/shm.c in the Linux kernel through 4.9.12 does not restrict the address calculated by a certain rounding operation, which allows local users to map page zero, and consequently bypass a protection mechanism that exists for the mmap system call, by making crafted shmget and shmat system calls in a privileged context.

In the Linux kernel, the following vulnerability has been resolved: isdn: cpai: check ctr->cnr to avoid array index out of bound The cmtp_add_connection() would add a cmtp session to a controller and run a kernel thread to process cmtp. __module_get(THIS_MODULE); session->task = kthread_run(cmtp_session, session, "kcmtpd_ctr_%d", session->num); During this process, the kernel thread would call detach_capi_ctr() to detach a register controller. if the controller was not attached yet, detach_capi_ctr() would trigger an array-index-out-bounds bug. [ 46.866069][ T6479] UBSAN: array-index-out-of-bounds in drivers/isdn/capi/kcapi.c:483:21 [ 46.867196][ T6479] index -1 is out of range for type 'capi_ctr *[32]' [ 46.867982][ T6479] CPU: 1 PID: 6479 Comm: kcmtpd_ctr_0 Not tainted 5.15.0-rc2+ #8 [ 46.869002][ T6479] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-2 04/01/2014 [ 46.870107][ T6479] Call Trace: [ 46.870473][ T6479] dump_stack_lvl+0x57/0x7d [ 46.870974][ T6479] ubsan_epilogue+0x5/0x40 [ 46.871458][ T6479] __ubsan_handle_out_of_bounds.cold+0x43/0x48 [ 46.872135][ T6479] detach_capi_ctr+0x64/0xc0 [ 46.872639][ T6479] cmtp_session+0x5c8/0x5d0 [ 46.873131][ T6479] ? __init_waitqueue_head+0x60/0x60 [ 46.873712][ T6479] ? cmtp_add_msgpart+0x120/0x120 [ 46.874256][ T6479] kthread+0x147/0x170 [ 46.874709][ T6479] ? set_kthread_struct+0x40/0x40 [ 46.875248][ T6479] ret_from_fork+0x1f/0x30 [ 46.875773][ T6479]

In the Linux kernel, the following vulnerability has been resolved: HID: core: zero-initialize the report buffer Since the report buffer is used by all kinds of drivers in various ways, let's zero-initialize it during allocation to make sure that it can't be ever used to leak kernel memory via specially-crafted report.

In the Linux kernel, the following vulnerability has been resolved: aoe: fix the potential use-after-free problem in more places For fixing CVE-2023-6270, f98364e92662 ("aoe: fix the potential use-after-free problem in aoecmd_cfg_pkts") makes tx() calling dev_put() instead of doing in aoecmd_cfg_pkts(). It avoids that the tx() runs into use-after-free. Then Nicolai Stange found more places in aoe have potential use-after-free problem with tx(). e.g. revalidate(), aoecmd_ata_rw(), resend(), probe() and aoecmd_cfg_rsp(). Those functions also use aoenet_xmit() to push packet to tx queue. So they should also use dev_hold() to increase the refcnt of skb->dev. On the other hand, moving dev_put() to tx() causes that the refcnt of skb->dev be reduced to a negative value, because corresponding dev_hold() are not called in revalidate(), aoecmd_ata_rw(), resend(), probe(), and aoecmd_cfg_rsp(). This patch fixed this issue.

In the Linux kernel, the following vulnerability has been resolved: ext4: fix timer use-after-free on failed mount Syzbot has found an ODEBUG bug in ext4_fill_super The del_timer_sync function cancels the s_err_report timer, which reminds about filesystem errors daily. We should guarantee the timer is no longer active before kfree(sbi). When filesystem mounting fails, the flow goes to failed_mount3, where an error occurs when ext4_stop_mmpd is called, causing a read I/O failure. This triggers the ext4_handle_error function that ultimately re-arms the timer, leaving the s_err_report timer active before kfree(sbi) is called. Fix the issue by canceling the s_err_report timer after calling ext4_stop_mmpd.

In the Linux kernel, the following vulnerability has been resolved: udf: fix uninit-value use in udf_get_fileshortad Check for overflow when computing alen in udf_current_aext to mitigate later uninit-value use in udf_get_fileshortad KMSAN bug[1]. After applying the patch reproducer did not trigger any issue[2]. [1] https://syzkaller.appspot.com/bug?extid=8901c4560b7ab5c2f9df [2] https://syzkaller.appspot.com/x/log.txt?x=10242227980000

In the Linux kernel, the following vulnerability has been resolved: vsock/virtio: Initialization of the dangling pointer occurring in vsk->trans During loopback communication, a dangling pointer can be created in vsk->trans, potentially leading to a Use-After-Free condition. This issue is resolved by initializing vsk->trans to NULL.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: add missing size check in amdgpu_debugfs_gprwave_read() Avoid a possible buffer overflow if size is larger than 4K. (cherry picked from commit f5d873f5825b40d886d03bd2aede91d4cf002434)

In the Linux kernel, the following vulnerability has been resolved: netfilter: bpf: must hold reference on net namespace BUG: KASAN: slab-use-after-free in __nf_unregister_net_hook+0x640/0x6b0 Read of size 8 at addr ffff8880106fe400 by task repro/72= bpf_nf_link_release+0xda/0x1e0 bpf_link_free+0x139/0x2d0 bpf_link_release+0x68/0x80 __fput+0x414/0xb60 Eric says: It seems that bpf was able to defer the __nf_unregister_net_hook() after exit()/close() time. Perhaps a netns reference is missing, because the netns has been dismantled/freed already. bpf_nf_link_attach() does : link->net = net; But I do not see a reference being taken on net. Add such a reference and release it after hook unreg. Note that I was unable to get syzbot reproducer to work, so I do not know if this resolves this splat.

In the Linux kernel, the following vulnerability has been resolved: x86/lam: Disable ADDRESS_MASKING in most cases Linear Address Masking (LAM) has a weakness related to transient execution as described in the SLAM paper[1]. Unless Linear Address Space Separation (LASS) is enabled this weakness may be exploitable. Until kernel adds support for LASS[2], only allow LAM for COMPILE_TEST, or when speculation mitigations have been disabled at compile time, otherwise keep LAM disabled. There are no processors in market that support LAM yet, so currently nobody is affected by this issue. [1] SLAM: https://download.vusec.net/papers/slam_sp24.pdf [2] LASS: https://lore.kernel.org/lkml/20230609183632.48706-1-alexander.shishkin@linux.intel.com/ [ dhansen: update SPECULATION_MITIGATIONS -> CPU_MITIGATIONS ]

In the Linux kernel, the following vulnerability has been resolved: net: ti: fix UAF in tlan_remove_one priv is netdev private data and it cannot be used after free_netdev() call. Using priv after free_netdev() can cause UAF bug. Fix it by moving free_netdev() at the end of the function.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: fix array out-of-bound access in SoC stats Currently, the ath12k_soc_dp_stats::hal_reo_error array is defined with a maximum size of DP_REO_DST_RING_MAX. However, the ath12k_dp_rx_process() function access ath12k_soc_dp_stats::hal_reo_error using the REO destination SRNG ring ID, which is incorrect. SRNG ring ID differ from normal ring ID, and this usage leads to out-of-bounds array access. To fix this issue, modify ath12k_dp_rx_process() to use the normal ring ID directly instead of the SRNG ring ID to avoid out-of-bounds array access. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix kernel bug due to missing clearing of checked flag Syzbot reported that in directory operations after nilfs2 detects filesystem corruption and degrades to read-only, __block_write_begin_int(), which is called to prepare block writes, may fail the BUG_ON check for accesses exceeding the folio/page size, triggering a kernel bug. This was found to be because the "checked" flag of a page/folio was not cleared when it was discarded by nilfs2's own routine, which causes the sanity check of directory entries to be skipped when the directory page/folio is reloaded. So, fix that. This was necessary when the use of nilfs2's own page discard routine was applied to more than just metadata files.

In the Linux kernel, the following vulnerability has been resolved: macsec: Fix use-after-free while sending the offloading packet KASAN reports the following UAF. The metadata_dst, which is used to store the SCI value for macsec offload, is already freed by metadata_dst_free() in macsec_free_netdev(), while driver still use it for sending the packet. To fix this issue, dst_release() is used instead to release metadata_dst. So it is not freed instantly in macsec_free_netdev() if still referenced by skb. BUG: KASAN: slab-use-after-free in mlx5e_xmit+0x1e8f/0x4190 [mlx5_core] Read of size 2 at addr ffff88813e42e038 by task kworker/7:2/714 [...] Workqueue: mld mld_ifc_work Call Trace: <TASK> dump_stack_lvl+0x51/0x60 print_report+0xc1/0x600 kasan_report+0xab/0xe0 mlx5e_xmit+0x1e8f/0x4190 [mlx5_core] dev_hard_start_xmit+0x120/0x530 sch_direct_xmit+0x149/0x11e0 __qdisc_run+0x3ad/0x1730 __dev_queue_xmit+0x1196/0x2ed0 vlan_dev_hard_start_xmit+0x32e/0x510 [8021q] dev_hard_start_xmit+0x120/0x530 __dev_queue_xmit+0x14a7/0x2ed0 macsec_start_xmit+0x13e9/0x2340 dev_hard_start_xmit+0x120/0x530 __dev_queue_xmit+0x14a7/0x2ed0 ip6_finish_output2+0x923/0x1a70 ip6_finish_output+0x2d7/0x970 ip6_output+0x1ce/0x3a0 NF_HOOK.constprop.0+0x15f/0x190 mld_sendpack+0x59a/0xbd0 mld_ifc_work+0x48a/0xa80 process_one_work+0x5aa/0xe50 worker_thread+0x79c/0x1290 kthread+0x28f/0x350 ret_from_fork+0x2d/0x70 ret_from_fork_asm+0x11/0x20 </TASK> Allocated by task 3922: kasan_save_stack+0x20/0x40 kasan_save_track+0x10/0x30 __kasan_kmalloc+0x77/0x90 __kmalloc_noprof+0x188/0x400 metadata_dst_alloc+0x1f/0x4e0 macsec_newlink+0x914/0x1410 __rtnl_newlink+0xe08/0x15b0 rtnl_newlink+0x5f/0x90 rtnetlink_rcv_msg+0x667/0xa80 netlink_rcv_skb+0x12c/0x360 netlink_unicast+0x551/0x770 netlink_sendmsg+0x72d/0xbd0 __sock_sendmsg+0xc5/0x190 ____sys_sendmsg+0x52e/0x6a0 ___sys_sendmsg+0xeb/0x170 __sys_sendmsg+0xb5/0x140 do_syscall_64+0x4c/0x100 entry_SYSCALL_64_after_hwframe+0x4b/0x53 Freed by task 4011: kasan_save_stack+0x20/0x40 kasan_save_track+0x10/0x30 kasan_save_free_info+0x37/0x50 poison_slab_object+0x10c/0x190 __kasan_slab_free+0x11/0x30 kfree+0xe0/0x290 macsec_free_netdev+0x3f/0x140 netdev_run_todo+0x450/0xc70 rtnetlink_rcv_msg+0x66f/0xa80 netlink_rcv_skb+0x12c/0x360 netlink_unicast+0x551/0x770 netlink_sendmsg+0x72d/0xbd0 __sock_sendmsg+0xc5/0x190 ____sys_sendmsg+0x52e/0x6a0 ___sys_sendmsg+0xeb/0x170 __sys_sendmsg+0xb5/0x140 do_syscall_64+0x4c/0x100 entry_SYSCALL_64_after_hwframe+0x4b/0x53

In the Linux kernel, the following vulnerability has been resolved: net: sched: fix use-after-free in taprio_change() In 'taprio_change()', 'admin' pointer may become dangling due to sched switch / removal caused by 'advance_sched()', and critical section protected by 'q->current_entry_lock' is too small to prevent from such a scenario (which causes use-after-free detected by KASAN). Fix this by prefer 'rcu_replace_pointer()' over 'rcu_assign_pointer()' to update 'admin' immediately before an attempt to schedule freeing.

Integer overflow in the check_offset function in b/wrestool/fileread.c in icoutils before 0.31.1 allows local users to cause a denial of service (process crash) and execute arbitrary code via a crafted executable.

In the Linux kernel, the following vulnerability has been resolved: mt76: mt7915: fix txrate reporting Properly check rate_info to fix unexpected reporting. [ 1215.161863] Call trace: [ 1215.164307] cfg80211_calculate_bitrate+0x124/0x200 [cfg80211] [ 1215.170139] ieee80211s_update_metric+0x80/0xc0 [mac80211] [ 1215.175624] ieee80211_tx_status_ext+0x508/0x838 [mac80211] [ 1215.181190] mt7915_mcu_get_rx_rate+0x28c/0x8d0 [mt7915e] [ 1215.186580] mt7915_mac_tx_free+0x324/0x7c0 [mt7915e] [ 1215.191623] mt7915_queue_rx_skb+0xa8/0xd0 [mt7915e] [ 1215.196582] mt76_dma_cleanup+0x7b0/0x11d0 [mt76] [ 1215.201276] __napi_poll+0x38/0xf8 [ 1215.204668] napi_workfn+0x40/0x80 [ 1215.208062] process_one_work+0x1fc/0x390 [ 1215.212062] worker_thread+0x48/0x4d0 [ 1215.215715] kthread+0x120/0x128 [ 1215.218935] ret_from_fork+0x10/0x1c

In the Linux kernel, the following vulnerability has been resolved: ext4: avoid OOB when system.data xattr changes underneath the filesystem When looking up for an entry in an inlined directory, if e_value_offs is changed underneath the filesystem by some change in the block device, it will lead to an out-of-bounds access that KASAN detects as an UAF. EXT4-fs (loop0): mounted filesystem 00000000-0000-0000-0000-000000000000 r/w without journal. Quota mode: none. loop0: detected capacity change from 2048 to 2047 ================================================================== BUG: KASAN: use-after-free in ext4_search_dir+0xf2/0x1c0 fs/ext4/namei.c:1500 Read of size 1 at addr ffff88803e91130f by task syz-executor269/5103 CPU: 0 UID: 0 PID: 5103 Comm: syz-executor269 Not tainted 6.11.0-rc4-syzkaller #0 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 Call Trace: <TASK> __dump_stack lib/dump_stack.c:93 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:119 print_address_description mm/kasan/report.c:377 [inline] print_report+0x169/0x550 mm/kasan/report.c:488 kasan_report+0x143/0x180 mm/kasan/report.c:601 ext4_search_dir+0xf2/0x1c0 fs/ext4/namei.c:1500 ext4_find_inline_entry+0x4be/0x5e0 fs/ext4/inline.c:1697 __ext4_find_entry+0x2b4/0x1b30 fs/ext4/namei.c:1573 ext4_lookup_entry fs/ext4/namei.c:1727 [inline] ext4_lookup+0x15f/0x750 fs/ext4/namei.c:1795 lookup_one_qstr_excl+0x11f/0x260 fs/namei.c:1633 filename_create+0x297/0x540 fs/namei.c:3980 do_symlinkat+0xf9/0x3a0 fs/namei.c:4587 __do_sys_symlinkat fs/namei.c:4610 [inline] __se_sys_symlinkat fs/namei.c:4607 [inline] __x64_sys_symlinkat+0x95/0xb0 fs/namei.c:4607 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f3e73ced469 Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 21 18 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007fff4d40c258 EFLAGS: 00000246 ORIG_RAX: 000000000000010a RAX: ffffffffffffffda RBX: 0032656c69662f2e RCX: 00007f3e73ced469 RDX: 0000000020000200 RSI: 00000000ffffff9c RDI: 00000000200001c0 RBP: 0000000000000000 R08: 00007fff4d40c290 R09: 00007fff4d40c290 R10: 0023706f6f6c2f76 R11: 0000000000000246 R12: 00007fff4d40c27c R13: 0000000000000003 R14: 431bde82d7b634db R15: 00007fff4d40c2b0 </TASK> Calling ext4_xattr_ibody_find right after reading the inode with ext4_get_inode_loc will lead to a check of the validity of the xattrs, avoiding this problem.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to avoid use-after-free in f2fs_stop_gc_thread() syzbot reports a f2fs bug as below: __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:114 print_report+0xe8/0x550 mm/kasan/report.c:491 kasan_report+0x143/0x180 mm/kasan/report.c:601 kasan_check_range+0x282/0x290 mm/kasan/generic.c:189 instrument_atomic_read_write include/linux/instrumented.h:96 [inline] atomic_fetch_add_relaxed include/linux/atomic/atomic-instrumented.h:252 [inline] __refcount_add include/linux/refcount.h:184 [inline] __refcount_inc include/linux/refcount.h:241 [inline] refcount_inc include/linux/refcount.h:258 [inline] get_task_struct include/linux/sched/task.h:118 [inline] kthread_stop+0xca/0x630 kernel/kthread.c:704 f2fs_stop_gc_thread+0x65/0xb0 fs/f2fs/gc.c:210 f2fs_do_shutdown+0x192/0x540 fs/f2fs/file.c:2283 f2fs_ioc_shutdown fs/f2fs/file.c:2325 [inline] __f2fs_ioctl+0x443a/0xbe60 fs/f2fs/file.c:4325 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:907 [inline] __se_sys_ioctl+0xfc/0x170 fs/ioctl.c:893 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f The root cause is below race condition, it may cause use-after-free issue in sbi->gc_th pointer. - remount - f2fs_remount - f2fs_stop_gc_thread - kfree(gc_th) - f2fs_ioc_shutdown - f2fs_do_shutdown - f2fs_stop_gc_thread - kthread_stop(gc_th->f2fs_gc_task) : sbi->gc_thread = NULL; We will call f2fs_do_shutdown() in two paths: - for f2fs_ioc_shutdown() path, we should grab sb->s_umount semaphore for fixing. - for f2fs_shutdown() path, it's safe since caller has already grabbed sb->s_umount semaphore.

An issue was discovered in aspeed_lpc_ctrl_mmap in drivers/soc/aspeed/aspeed-lpc-ctrl.c in the Linux kernel before 5.14.6. Local attackers able to access the Aspeed LPC control interface could overwrite memory in the kernel and potentially execute privileges, aka CID-b49a0e69a7b1. This occurs because a certain comparison uses values that are not memory sizes.

In the Linux kernel, the following vulnerability has been resolved: x86/tdx: Fix "in-kernel MMIO" check TDX only supports kernel-initiated MMIO operations. The handle_mmio() function checks if the #VE exception occurred in the kernel and rejects the operation if it did not. However, userspace can deceive the kernel into performing MMIO on its behalf. For example, if userspace can point a syscall to an MMIO address, syscall does get_user() or put_user() on it, triggering MMIO #VE. The kernel will treat the #VE as in-kernel MMIO. Ensure that the target MMIO address is within the kernel before decoding instruction.

In the Linux kernel, the following vulnerability has been resolved: af_unix: Don't return OOB skb in manage_oob(). syzbot reported use-after-free in unix_stream_recv_urg(). [0] The scenario is 1. send(MSG_OOB) 2. recv(MSG_OOB) -> The consumed OOB remains in recv queue 3. send(MSG_OOB) 4. recv() -> manage_oob() returns the next skb of the consumed OOB -> This is also OOB, but unix_sk(sk)->oob_skb is not cleared 5. recv(MSG_OOB) -> unix_sk(sk)->oob_skb is used but already freed The recent commit 8594d9b85c07 ("af_unix: Don't call skb_get() for OOB skb.") uncovered the issue. If the OOB skb is consumed and the next skb is peeked in manage_oob(), we still need to check if the skb is OOB. Let's do so by falling back to the following checks in manage_oob() and add the test case in selftest. Note that we need to add a similar check for SIOCATMARK. [0]: BUG: KASAN: slab-use-after-free in unix_stream_read_actor+0xa6/0xb0 net/unix/af_unix.c:2959 Read of size 4 at addr ffff8880326abcc4 by task syz-executor178/5235 CPU: 0 UID: 0 PID: 5235 Comm: syz-executor178 Not tainted 6.11.0-rc5-syzkaller-00742-gfbdaffe41adc #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/06/2024 Call Trace: <TASK> __dump_stack lib/dump_stack.c:93 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:119 print_address_description mm/kasan/report.c:377 [inline] print_report+0x169/0x550 mm/kasan/report.c:488 kasan_report+0x143/0x180 mm/kasan/report.c:601 unix_stream_read_actor+0xa6/0xb0 net/unix/af_unix.c:2959 unix_stream_recv_urg+0x1df/0x320 net/unix/af_unix.c:2640 unix_stream_read_generic+0x2456/0x2520 net/unix/af_unix.c:2778 unix_stream_recvmsg+0x22b/0x2c0 net/unix/af_unix.c:2996 sock_recvmsg_nosec net/socket.c:1046 [inline] sock_recvmsg+0x22f/0x280 net/socket.c:1068 ____sys_recvmsg+0x1db/0x470 net/socket.c:2816 ___sys_recvmsg net/socket.c:2858 [inline] __sys_recvmsg+0x2f0/0x3e0 net/socket.c:2888 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f5360d6b4e9 Code: 48 83 c4 28 c3 e8 37 17 00 00 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007fff29b3a458 EFLAGS: 00000246 ORIG_RAX: 000000000000002f RAX: ffffffffffffffda RBX: 00007fff29b3a638 RCX: 00007f5360d6b4e9 RDX: 0000000000002001 RSI: 0000000020000640 RDI: 0000000000000003 RBP: 00007f5360dde610 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000001 R13: 00007fff29b3a628 R14: 0000000000000001 R15: 0000000000000001 </TASK> Allocated by task 5235: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x3f/0x80 mm/kasan/common.c:68 unpoison_slab_object mm/kasan/common.c:312 [inline] __kasan_slab_alloc+0x66/0x80 mm/kasan/common.c:338 kasan_slab_alloc include/linux/kasan.h:201 [inline] slab_post_alloc_hook mm/slub.c:3988 [inline] slab_alloc_node mm/slub.c:4037 [inline] kmem_cache_alloc_node_noprof+0x16b/0x320 mm/slub.c:4080 __alloc_skb+0x1c3/0x440 net/core/skbuff.c:667 alloc_skb include/linux/skbuff.h:1320 [inline] alloc_skb_with_frags+0xc3/0x770 net/core/skbuff.c:6528 sock_alloc_send_pskb+0x91a/0xa60 net/core/sock.c:2815 sock_alloc_send_skb include/net/sock.h:1778 [inline] queue_oob+0x108/0x680 net/unix/af_unix.c:2198 unix_stream_sendmsg+0xd24/0xf80 net/unix/af_unix.c:2351 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x221/0x270 net/socket.c:745 ____sys_sendmsg+0x525/0x7d0 net/socket.c:2597 ___sys_sendmsg net/socket.c:2651 [inline] __sys_sendmsg+0x2b0/0x3a0 net/socket.c:2680 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f Freed by task 5235: kasan_save_stack mm/kasan/common.c:47 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix double put of @cfile in smb2_set_path_size() If smb2_compound_op() is called with a valid @cfile and returned -EINVAL, we need to call cifs_get_writable_path() before retrying it as the reference of @cfile was already dropped by previous call. This fixes the following KASAN splat when running fstests generic/013 against Windows Server 2022: CIFS: Attempting to mount //w22-fs0/scratch run fstests generic/013 at 2024-09-02 19:48:59 ================================================================== BUG: KASAN: slab-use-after-free in detach_if_pending+0xab/0x200 Write of size 8 at addr ffff88811f1a3730 by task kworker/3:2/176 CPU: 3 UID: 0 PID: 176 Comm: kworker/3:2 Not tainted 6.11.0-rc6 #2 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-2.fc40 04/01/2014 Workqueue: cifsoplockd cifs_oplock_break [cifs] Call Trace: <TASK> dump_stack_lvl+0x5d/0x80 ? detach_if_pending+0xab/0x200 print_report+0x156/0x4d9 ? detach_if_pending+0xab/0x200 ? __virt_addr_valid+0x145/0x300 ? __phys_addr+0x46/0x90 ? detach_if_pending+0xab/0x200 kasan_report+0xda/0x110 ? detach_if_pending+0xab/0x200 detach_if_pending+0xab/0x200 timer_delete+0x96/0xe0 ? __pfx_timer_delete+0x10/0x10 ? rcu_is_watching+0x20/0x50 try_to_grab_pending+0x46/0x3b0 __cancel_work+0x89/0x1b0 ? __pfx___cancel_work+0x10/0x10 ? kasan_save_track+0x14/0x30 cifs_close_deferred_file+0x110/0x2c0 [cifs] ? __pfx_cifs_close_deferred_file+0x10/0x10 [cifs] ? __pfx_down_read+0x10/0x10 cifs_oplock_break+0x4c1/0xa50 [cifs] ? __pfx_cifs_oplock_break+0x10/0x10 [cifs] ? lock_is_held_type+0x85/0xf0 ? mark_held_locks+0x1a/0x90 process_one_work+0x4c6/0x9f0 ? find_held_lock+0x8a/0xa0 ? __pfx_process_one_work+0x10/0x10 ? lock_acquired+0x220/0x550 ? __list_add_valid_or_report+0x37/0x100 worker_thread+0x2e4/0x570 ? __kthread_parkme+0xd1/0xf0 ? __pfx_worker_thread+0x10/0x10 kthread+0x17f/0x1c0 ? kthread+0xda/0x1c0 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x31/0x60 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> Allocated by task 1118: kasan_save_stack+0x30/0x50 kasan_save_track+0x14/0x30 __kasan_kmalloc+0xaa/0xb0 cifs_new_fileinfo+0xc8/0x9d0 [cifs] cifs_atomic_open+0x467/0x770 [cifs] lookup_open.isra.0+0x665/0x8b0 path_openat+0x4c3/0x1380 do_filp_open+0x167/0x270 do_sys_openat2+0x129/0x160 __x64_sys_creat+0xad/0xe0 do_syscall_64+0xbb/0x1d0 entry_SYSCALL_64_after_hwframe+0x77/0x7f Freed by task 83: kasan_save_stack+0x30/0x50 kasan_save_track+0x14/0x30 kasan_save_free_info+0x3b/0x70 poison_slab_object+0xe9/0x160 __kasan_slab_free+0x32/0x50 kfree+0xf2/0x300 process_one_work+0x4c6/0x9f0 worker_thread+0x2e4/0x570 kthread+0x17f/0x1c0 ret_from_fork+0x31/0x60 ret_from_fork_asm+0x1a/0x30 Last potentially related work creation: kasan_save_stack+0x30/0x50 __kasan_record_aux_stack+0xad/0xc0 insert_work+0x29/0xe0 __queue_work+0x5ea/0x760 queue_work_on+0x6d/0x90 _cifsFileInfo_put+0x3f6/0x770 [cifs] smb2_compound_op+0x911/0x3940 [cifs] smb2_set_path_size+0x228/0x270 [cifs] cifs_set_file_size+0x197/0x460 [cifs] cifs_setattr+0xd9c/0x14b0 [cifs] notify_change+0x4e3/0x740 do_truncate+0xfa/0x180 vfs_truncate+0x195/0x200 __x64_sys_truncate+0x109/0x150 do_syscall_64+0xbb/0x1d0 entry_SYSCALL_64_after_hwframe+0x77/0x7f

In the Linux kernel, the following vulnerability has been resolved: net: sched: flower: protect fl_walk() with rcu Patch that refactored fl_walk() to use idr_for_each_entry_continue_ul() also removed rcu protection of individual filters which causes following use-after-free when filter is deleted concurrently. Fix fl_walk() to obtain rcu read lock while iterating and taking the filter reference and temporary release the lock while calling arg->fn() callback that can sleep. KASAN trace: [ 352.773640] ================================================================== [ 352.775041] BUG: KASAN: use-after-free in fl_walk+0x159/0x240 [cls_flower] [ 352.776304] Read of size 4 at addr ffff8881c8251480 by task tc/2987 [ 352.777862] CPU: 3 PID: 2987 Comm: tc Not tainted 5.15.0-rc2+ #2 [ 352.778980] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 [ 352.781022] Call Trace: [ 352.781573] dump_stack_lvl+0x46/0x5a [ 352.782332] print_address_description.constprop.0+0x1f/0x140 [ 352.783400] ? fl_walk+0x159/0x240 [cls_flower] [ 352.784292] ? fl_walk+0x159/0x240 [cls_flower] [ 352.785138] kasan_report.cold+0x83/0xdf [ 352.785851] ? fl_walk+0x159/0x240 [cls_flower] [ 352.786587] kasan_check_range+0x145/0x1a0 [ 352.787337] fl_walk+0x159/0x240 [cls_flower] [ 352.788163] ? fl_put+0x10/0x10 [cls_flower] [ 352.789007] ? __mutex_unlock_slowpath.constprop.0+0x220/0x220 [ 352.790102] tcf_chain_dump+0x231/0x450 [ 352.790878] ? tcf_chain_tp_delete_empty+0x170/0x170 [ 352.791833] ? __might_sleep+0x2e/0xc0 [ 352.792594] ? tfilter_notify+0x170/0x170 [ 352.793400] ? __mutex_unlock_slowpath.constprop.0+0x220/0x220 [ 352.794477] tc_dump_tfilter+0x385/0x4b0 [ 352.795262] ? tc_new_tfilter+0x1180/0x1180 [ 352.796103] ? __mod_node_page_state+0x1f/0xc0 [ 352.796974] ? __build_skb_around+0x10e/0x130 [ 352.797826] netlink_dump+0x2c0/0x560 [ 352.798563] ? netlink_getsockopt+0x430/0x430 [ 352.799433] ? __mutex_unlock_slowpath.constprop.0+0x220/0x220 [ 352.800542] __netlink_dump_start+0x356/0x440 [ 352.801397] rtnetlink_rcv_msg+0x3ff/0x550 [ 352.802190] ? tc_new_tfilter+0x1180/0x1180 [ 352.802872] ? rtnl_calcit.isra.0+0x1f0/0x1f0 [ 352.803668] ? tc_new_tfilter+0x1180/0x1180 [ 352.804344] ? _copy_from_iter_nocache+0x800/0x800 [ 352.805202] ? kasan_set_track+0x1c/0x30 [ 352.805900] netlink_rcv_skb+0xc6/0x1f0 [ 352.806587] ? rht_deferred_worker+0x6b0/0x6b0 [ 352.807455] ? rtnl_calcit.isra.0+0x1f0/0x1f0 [ 352.808324] ? netlink_ack+0x4d0/0x4d0 [ 352.809086] ? netlink_deliver_tap+0x62/0x3d0 [ 352.809951] netlink_unicast+0x353/0x480 [ 352.810744] ? netlink_attachskb+0x430/0x430 [ 352.811586] ? __alloc_skb+0xd7/0x200 [ 352.812349] netlink_sendmsg+0x396/0x680 [ 352.813132] ? netlink_unicast+0x480/0x480 [ 352.813952] ? __import_iovec+0x192/0x210 [ 352.814759] ? netlink_unicast+0x480/0x480 [ 352.815580] sock_sendmsg+0x6c/0x80 [ 352.816299] ____sys_sendmsg+0x3a5/0x3c0 [ 352.817096] ? kernel_sendmsg+0x30/0x30 [ 352.817873] ? __ia32_sys_recvmmsg+0x150/0x150 [ 352.818753] ___sys_sendmsg+0xd8/0x140 [ 352.819518] ? sendmsg_copy_msghdr+0x110/0x110 [ 352.820402] ? ___sys_recvmsg+0xf4/0x1a0 [ 352.821110] ? __copy_msghdr_from_user+0x260/0x260 [ 352.821934] ? _raw_spin_lock+0x81/0xd0 [ 352.822680] ? __handle_mm_fault+0xef3/0x1b20 [ 352.823549] ? rb_insert_color+0x2a/0x270 [ 352.824373] ? copy_page_range+0x16b0/0x16b0 [ 352.825209] ? perf_event_update_userpage+0x2d0/0x2d0 [ 352.826190] ? __fget_light+0xd9/0xf0 [ 352.826941] __sys_sendmsg+0xb3/0x130 [ 352.827613] ? __sys_sendmsg_sock+0x20/0x20 [ 352.828377] ? do_user_addr_fault+0x2c5/0x8a0 [ 352.829184] ? fpregs_assert_state_consistent+0x52/0x60 [ 352.830001] ? exit_to_user_mode_prepare+0x32/0x160 [ 352.830845] do_syscall_64+0x35/0x80 [ 352.831445] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 352.832331] RIP: 0033:0x7f7bee973c17 [ ---truncated---

In the Linux kernel, the following vulnerability has been resolved: ASoC: meson: axg-card: fix 'use-after-free' Buffer 'card->dai_link' is reallocated in 'meson_card_reallocate_links()', so move 'pad' pointer initialization after this function when memory is already reallocated. Kasan bug report: ================================================================== BUG: KASAN: slab-use-after-free in axg_card_add_link+0x76c/0x9bc Read of size 8 at addr ffff000000e8b260 by task modprobe/356 CPU: 0 PID: 356 Comm: modprobe Tainted: G O 6.9.12-sdkernel #1 Call trace: dump_backtrace+0x94/0xec show_stack+0x18/0x24 dump_stack_lvl+0x78/0x90 print_report+0xfc/0x5c0 kasan_report+0xb8/0xfc __asan_load8+0x9c/0xb8 axg_card_add_link+0x76c/0x9bc [snd_soc_meson_axg_sound_card] meson_card_probe+0x344/0x3b8 [snd_soc_meson_card_utils] platform_probe+0x8c/0xf4 really_probe+0x110/0x39c __driver_probe_device+0xb8/0x18c driver_probe_device+0x108/0x1d8 __driver_attach+0xd0/0x25c bus_for_each_dev+0xe0/0x154 driver_attach+0x34/0x44 bus_add_driver+0x134/0x294 driver_register+0xa8/0x1e8 __platform_driver_register+0x44/0x54 axg_card_pdrv_init+0x20/0x1000 [snd_soc_meson_axg_sound_card] do_one_initcall+0xdc/0x25c do_init_module+0x10c/0x334 load_module+0x24c4/0x26cc init_module_from_file+0xd4/0x128 __arm64_sys_finit_module+0x1f4/0x41c invoke_syscall+0x60/0x188 el0_svc_common.constprop.0+0x78/0x13c do_el0_svc+0x30/0x40 el0_svc+0x38/0x78 el0t_64_sync_handler+0x100/0x12c el0t_64_sync+0x190/0x194

In the Linux kernel, the following vulnerability has been resolved: bus: mhi: core: Validate channel ID when processing command completions MHI reads the channel ID from the event ring element sent by the device which can be any value between 0 and 255. In order to prevent any out of bound accesses, add a check against the maximum number of channels supported by the controller and those channels not configured yet so as to skip processing of that event ring element.

In the Linux kernel, the following vulnerability has been resolved: drm/xe: prevent UAF around preempt fence The fence lock is part of the queue, therefore in the current design anything locking the fence should then also hold a ref to the queue to prevent the queue from being freed. However, currently it looks like we signal the fence and then drop the queue ref, but if something is waiting on the fence, the waiter is kicked to wake up at some later point, where upon waking up it first grabs the lock before checking the fence state. But if we have already dropped the queue ref, then the lock might already be freed as part of the queue, leading to uaf. To prevent this, move the fence lock into the fence itself so we don't run into lifetime issues. Alternative might be to have device level lock, or only release the queue in the fence release callback, however that might require pushing to another worker to avoid locking issues. References: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/2454 References: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/2342 References: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/2020 (cherry picked from commit 7116c35aacedc38be6d15bd21b2fc936eed0008b)

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/vcn: remove irq disabling in vcn 5 suspend We do not directly enable/disable VCN IRQ in vcn 5.0.0. And we do not handle the IRQ state as well. So the calls to disable IRQ and set state are removed. This effectively gets rid of the warining of "WARN_ON(!amdgpu_irq_enabled(adev, src, type))" in amdgpu_irq_put().

In the Linux kernel, the following vulnerability has been resolved: can: sja1000: fix use after free in ems_pcmcia_add_card() If the last channel is not available then "dev" is freed. Fortunately, we can just use "pdev->irq" instead. Also we should check if at least one channel was set up.

In the Linux kernel, the following vulnerability has been resolved: gfs2: Fix use-after-free in gfs2_glock_shrink_scan The GLF_LRU flag is checked under lru_lock in gfs2_glock_remove_from_lru() to remove the glock from the lru list in __gfs2_glock_put(). On the shrink scan path, the same flag is cleared under lru_lock but because of cond_resched_lock(&lru_lock) in gfs2_dispose_glock_lru(), progress on the put side can be made without deleting the glock from the lru list. Keep GLF_LRU across the race window opened by cond_resched_lock(&lru_lock) to ensure correct behavior on both sides - clear GLF_LRU after list_del under lru_lock.