In the Linux kernel, the following vulnerability has been resolved: ice: Don't process extts if PTP is disabled The ice_ptp_extts_event() function can race with ice_ptp_release() and result in a NULL pointer dereference which leads to a kernel panic. Panic occurs because the ice_ptp_extts_event() function calls ptp_clock_event() with a NULL pointer. The ice driver has already released the PTP clock by the time the interrupt for the next external timestamp event occurs. To fix this, modify the ice_ptp_extts_event() function to check the PTP state and bail early if PTP is not ready.

In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Complete command early within lock A crash was observed while performing NPIV and FW reset, BUG: kernel NULL pointer dereference, address: 000000000000001c #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 1 PREEMPT_RT SMP NOPTI RIP: 0010:dma_direct_unmap_sg+0x51/0x1e0 RSP: 0018:ffffc90026f47b88 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000021 RCX: 0000000000000002 RDX: 0000000000000021 RSI: 0000000000000000 RDI: ffff8881041130d0 RBP: ffff8881041130d0 R08: 0000000000000000 R09: 0000000000000034 R10: ffffc90026f47c48 R11: 0000000000000031 R12: 0000000000000000 R13: 0000000000000000 R14: ffff8881565e4a20 R15: 0000000000000000 FS: 00007f4c69ed3d00(0000) GS:ffff889faac80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000000000001c CR3: 0000000288a50002 CR4: 00000000007706e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> ? __die_body+0x1a/0x60 ? page_fault_oops+0x16f/0x4a0 ? do_user_addr_fault+0x174/0x7f0 ? exc_page_fault+0x69/0x1a0 ? asm_exc_page_fault+0x22/0x30 ? dma_direct_unmap_sg+0x51/0x1e0 ? preempt_count_sub+0x96/0xe0 qla2xxx_qpair_sp_free_dma+0x29f/0x3b0 [qla2xxx] qla2xxx_qpair_sp_compl+0x60/0x80 [qla2xxx] __qla2x00_abort_all_cmds+0xa2/0x450 [qla2xxx] The command completion was done early while aborting the commands in driver unload path but outside lock to avoid the WARN_ON condition of performing dma_free_attr within the lock. However this caused race condition while command completion via multiple paths causing system crash. Hence complete the command early in unload path but within the lock to avoid race condition.

In the Linux kernel, the following vulnerability has been resolved: ocfs2: fix races between hole punching and AIO+DIO After commit "ocfs2: return real error code in ocfs2_dio_wr_get_block", fstests/generic/300 become from always failed to sometimes failed: ======================================================================== [ 473.293420 ] run fstests generic/300 [ 475.296983 ] JBD2: Ignoring recovery information on journal [ 475.302473 ] ocfs2: Mounting device (253,1) on (node local, slot 0) with ordered data mode. [ 494.290998 ] OCFS2: ERROR (device dm-1): ocfs2_change_extent_flag: Owner 5668 has an extent at cpos 78723 which can no longer be found [ 494.291609 ] On-disk corruption discovered. Please run fsck.ocfs2 once the filesystem is unmounted. [ 494.292018 ] OCFS2: File system is now read-only. [ 494.292224 ] (kworker/19:11,2628,19):ocfs2_mark_extent_written:5272 ERROR: status = -30 [ 494.292602 ] (kworker/19:11,2628,19):ocfs2_dio_end_io_write:2374 ERROR: status = -3 fio: io_u error on file /mnt/scratch/racer: Read-only file system: write offset=460849152, buflen=131072 ========================================================================= In __blockdev_direct_IO, ocfs2_dio_wr_get_block is called to add unwritten extents to a list. extents are also inserted into extent tree in ocfs2_write_begin_nolock. Then another thread call fallocate to puch a hole at one of the unwritten extent. The extent at cpos was removed by ocfs2_remove_extent(). At end io worker thread, ocfs2_search_extent_list found there is no such extent at the cpos. T1 T2 T3 inode lock ... insert extents ... inode unlock ocfs2_fallocate __ocfs2_change_file_space inode lock lock ip_alloc_sem ocfs2_remove_inode_range inode ocfs2_remove_btree_range ocfs2_remove_extent ^---remove the extent at cpos 78723 ... unlock ip_alloc_sem inode unlock ocfs2_dio_end_io ocfs2_dio_end_io_write lock ip_alloc_sem ocfs2_mark_extent_written ocfs2_change_extent_flag ocfs2_search_extent_list ^---failed to find extent ... unlock ip_alloc_sem In most filesystems, fallocate is not compatible with racing with AIO+DIO, so fix it by adding to wait for all dio before fallocate/punch_hole like ext4.

In the Linux kernel, the following vulnerability has been resolved: sock_map: avoid race between sock_map_close and sk_psock_put sk_psock_get will return NULL if the refcount of psock has gone to 0, which will happen when the last call of sk_psock_put is done. However, sk_psock_drop may not have finished yet, so the close callback will still point to sock_map_close despite psock being NULL. This can be reproduced with a thread deleting an element from the sock map, while the second one creates a socket, adds it to the map and closes it. That will trigger the WARN_ON_ONCE: ------------[ cut here ]------------ WARNING: CPU: 1 PID: 7220 at net/core/sock_map.c:1701 sock_map_close+0x2a2/0x2d0 net/core/sock_map.c:1701 Modules linked in: CPU: 1 PID: 7220 Comm: syz-executor380 Not tainted 6.9.0-syzkaller-07726-g3c999d1ae3c7 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/02/2024 RIP: 0010:sock_map_close+0x2a2/0x2d0 net/core/sock_map.c:1701 Code: df e8 92 29 88 f8 48 8b 1b 48 89 d8 48 c1 e8 03 42 80 3c 20 00 74 08 48 89 df e8 79 29 88 f8 4c 8b 23 eb 89 e8 4f 15 23 f8 90 <0f> 0b 90 48 83 c4 08 5b 41 5c 41 5d 41 5e 41 5f 5d e9 13 26 3d 02 RSP: 0018:ffffc9000441fda8 EFLAGS: 00010293 RAX: ffffffff89731ae1 RBX: ffffffff94b87540 RCX: ffff888029470000 RDX: 0000000000000000 RSI: ffffffff8bcab5c0 RDI: ffffffff8c1faba0 RBP: 0000000000000000 R08: ffffffff92f9b61f R09: 1ffffffff25f36c3 R10: dffffc0000000000 R11: fffffbfff25f36c4 R12: ffffffff89731840 R13: ffff88804b587000 R14: ffff88804b587000 R15: ffffffff89731870 FS: 000055555e080380(0000) GS:ffff8880b9500000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 00000000207d4000 CR4: 0000000000350ef0 Call Trace: <TASK> unix_release+0x87/0xc0 net/unix/af_unix.c:1048 __sock_release net/socket.c:659 [inline] sock_close+0xbe/0x240 net/socket.c:1421 __fput+0x42b/0x8a0 fs/file_table.c:422 __do_sys_close fs/open.c:1556 [inline] __se_sys_close fs/open.c:1541 [inline] __x64_sys_close+0x7f/0x110 fs/open.c:1541 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf5/0x240 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7fb37d618070 Code: 00 00 48 c7 c2 b8 ff ff ff f7 d8 64 89 02 b8 ff ff ff ff eb d4 e8 10 2c 00 00 80 3d 31 f0 07 00 00 74 17 b8 03 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 48 c3 0f 1f 80 00 00 00 00 48 83 ec 18 89 7c RSP: 002b:00007ffcd4a525d8 EFLAGS: 00000202 ORIG_RAX: 0000000000000003 RAX: ffffffffffffffda RBX: 0000000000000005 RCX: 00007fb37d618070 RDX: 0000000000000010 RSI: 00000000200001c0 RDI: 0000000000000004 RBP: 0000000000000000 R08: 0000000100000000 R09: 0000000100000000 R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000000000 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 </TASK> Use sk_psock, which will only check that the pointer is not been set to NULL yet, which should only happen after the callbacks are restored. If, then, a reference can still be gotten, we may call sk_psock_stop and cancel psock->work. As suggested by Paolo Abeni, reorder the condition so the control flow is less convoluted. After that change, the reproducer does not trigger the WARN_ON_ONCE anymore.

In the Linux kernel, the following vulnerability has been resolved: dm: fix mempool NULL pointer race when completing IO dm_io_dec_pending() calls end_io_acct() first and will then dec md in-flight pending count. But if a task is swapping DM table at same time this can result in a crash due to mempool->elements being NULL: task1 task2 do_resume ->do_suspend ->dm_wait_for_completion bio_endio ->clone_endio ->dm_io_dec_pending ->end_io_acct ->wakeup task1 ->dm_swap_table ->__bind ->__bind_mempools ->bioset_exit ->mempool_exit ->free_io [ 67.330330] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 ...... [ 67.330494] pstate: 80400085 (Nzcv daIf +PAN -UAO) [ 67.330510] pc : mempool_free+0x70/0xa0 [ 67.330515] lr : mempool_free+0x4c/0xa0 [ 67.330520] sp : ffffff8008013b20 [ 67.330524] x29: ffffff8008013b20 x28: 0000000000000004 [ 67.330530] x27: ffffffa8c2ff40a0 x26: 00000000ffff1cc8 [ 67.330535] x25: 0000000000000000 x24: ffffffdada34c800 [ 67.330541] x23: 0000000000000000 x22: ffffffdada34c800 [ 67.330547] x21: 00000000ffff1cc8 x20: ffffffd9a1304d80 [ 67.330552] x19: ffffffdada34c970 x18: 000000b312625d9c [ 67.330558] x17: 00000000002dcfbf x16: 00000000000006dd [ 67.330563] x15: 000000000093b41e x14: 0000000000000010 [ 67.330569] x13: 0000000000007f7a x12: 0000000034155555 [ 67.330574] x11: 0000000000000001 x10: 0000000000000001 [ 67.330579] x9 : 0000000000000000 x8 : 0000000000000000 [ 67.330585] x7 : 0000000000000000 x6 : ffffff80148b5c1a [ 67.330590] x5 : ffffff8008013ae0 x4 : 0000000000000001 [ 67.330596] x3 : ffffff80080139c8 x2 : ffffff801083bab8 [ 67.330601] x1 : 0000000000000000 x0 : ffffffdada34c970 [ 67.330609] Call trace: [ 67.330616] mempool_free+0x70/0xa0 [ 67.330627] bio_put+0xf8/0x110 [ 67.330638] dec_pending+0x13c/0x230 [ 67.330644] clone_endio+0x90/0x180 [ 67.330649] bio_endio+0x198/0x1b8 [ 67.330655] dec_pending+0x190/0x230 [ 67.330660] clone_endio+0x90/0x180 [ 67.330665] bio_endio+0x198/0x1b8 [ 67.330673] blk_update_request+0x214/0x428 [ 67.330683] scsi_end_request+0x2c/0x300 [ 67.330688] scsi_io_completion+0xa0/0x710 [ 67.330695] scsi_finish_command+0xd8/0x110 [ 67.330700] scsi_softirq_done+0x114/0x148 [ 67.330708] blk_done_softirq+0x74/0xd0 [ 67.330716] __do_softirq+0x18c/0x374 [ 67.330724] irq_exit+0xb4/0xb8 [ 67.330732] __handle_domain_irq+0x84/0xc0 [ 67.330737] gic_handle_irq+0x148/0x1b0 [ 67.330744] el1_irq+0xe8/0x190 [ 67.330753] lpm_cpuidle_enter+0x4f8/0x538 [ 67.330759] cpuidle_enter_state+0x1fc/0x398 [ 67.330764] cpuidle_enter+0x18/0x20 [ 67.330772] do_idle+0x1b4/0x290 [ 67.330778] cpu_startup_entry+0x20/0x28 [ 67.330786] secondary_start_kernel+0x160/0x170 Fix this by: 1) Establishing pointers to 'struct dm_io' members in dm_io_dec_pending() so that they may be passed into end_io_acct() _after_ free_io() is called. 2) Moving end_io_acct() after free_io().

In the Linux kernel, the following vulnerability has been resolved: btrfs: protect folio::private when attaching extent buffer folios [BUG] Since v6.8 there are rare kernel crashes reported by various people, the common factor is bad page status error messages like this: BUG: Bad page state in process kswapd0 pfn:d6e840 page: refcount:0 mapcount:0 mapping:000000007512f4f2 index:0x2796c2c7c pfn:0xd6e840 aops:btree_aops ino:1 flags: 0x17ffffe0000008(uptodate|node=0|zone=2|lastcpupid=0x3fffff) page_type: 0xffffffff() raw: 0017ffffe0000008 dead000000000100 dead000000000122 ffff88826d0be4c0 raw: 00000002796c2c7c 0000000000000000 00000000ffffffff 0000000000000000 page dumped because: non-NULL mapping [CAUSE] Commit 09e6cef19c9f ("btrfs: refactor alloc_extent_buffer() to allocate-then-attach method") changes the sequence when allocating a new extent buffer. Previously we always called grab_extent_buffer() under mapping->i_private_lock, to ensure the safety on modification on folio::private (which is a pointer to extent buffer for regular sectorsize). This can lead to the following race: Thread A is trying to allocate an extent buffer at bytenr X, with 4 4K pages, meanwhile thread B is trying to release the page at X + 4K (the second page of the extent buffer at X). Thread A | Thread B -----------------------------------+------------------------------------- | btree_release_folio() | | This is for the page at X + 4K, | | Not page X. | | alloc_extent_buffer() | |- release_extent_buffer() |- filemap_add_folio() for the | | |- atomic_dec_and_test(eb->refs) | page at bytenr X (the first | | | | page). | | | | Which returned -EEXIST. | | | | | | | |- filemap_lock_folio() | | | | Returned the first page locked. | | | | | | | |- grab_extent_buffer() | | | | |- atomic_inc_not_zero() | | | | | Returned false | | | | |- folio_detach_private() | | |- folio_detach_private() for X | |- folio_test_private() | | |- folio_test_private() | Returned true | | | Returned true |- folio_put() | |- folio_put() Now there are two puts on the same folio at folio X, leading to refcount underflow of the folio X, and eventually causing the BUG_ON() on the page->mapping. The condition is not that easy to hit: - The release must be triggered for the middle page of an eb If the release is on the same first page of an eb, page lock would kick in and prevent the race. - folio_detach_private() has a very small race window It's only between folio_test_private() and folio_clear_private(). That's exactly when mapping->i_private_lock is used to prevent such race, and commit 09e6cef19c9f ("btrfs: refactor alloc_extent_buffer() to allocate-then-attach method") screwed that up. At that time, I thought the page lock would kick in as filemap_release_folio() also requires the page to be locked, but forgot the filemap_release_folio() only locks one page, not all pages of an extent buffer. [FIX] Move all the code requiring i_private_lock into attach_eb_folio_to_filemap(), so that everything is done with proper lock protection. Furthermore to prevent future problems, add an extra lockdep_assert_locked() to ensure we're holding the proper lock. To reproducer that is able to hit the race (takes a few minutes with instrumented code inserting delays to alloc_extent_buffer()): #!/bin/sh drop_caches () { while(true); do echo 3 > /proc/sys/vm/drop_caches echo 1 > /proc/sys/vm/compact_memory done } run_tar () { while(true); do for x in `seq 1 80` ; do tar cf /dev/zero /mnt > /dev/null & done wait done } mkfs.btrfs -f -d single -m single ---truncated---

In the Linux kernel, the following vulnerability has been resolved: usb: yurex: fix race in probe The bbu member of the descriptor must be set to the value standing for uninitialized values before the URB whose completion handler sets bbu is submitted. Otherwise there is a window during which probing can overwrite already retrieved data.

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: f_rndis: Protect RNDIS options with mutex The class/subclass/protocol options are suspectible to race conditions as they can be accessed concurrently through configfs. Use existing mutex to protect these options. This issue was identified during code inspection.

In the Linux kernel, the following vulnerability has been resolved: cgroup: fix race between task migration and iteration When a task is migrated out of a css_set, cgroup_migrate_add_task() first moves it from cset->tasks to cset->mg_tasks via: list_move_tail(&task->cg_list, &cset->mg_tasks); If a css_task_iter currently has it->task_pos pointing to this task, css_set_move_task() calls css_task_iter_skip() to keep the iterator valid. However, since the task has already been moved to ->mg_tasks, the iterator is advanced relative to the mg_tasks list instead of the original tasks list. As a result, remaining tasks on cset->tasks, as well as tasks queued on cset->mg_tasks, can be skipped by iteration. Fix this by calling css_set_skip_task_iters() before unlinking task->cg_list from cset->tasks. This advances all active iterators to the next task on cset->tasks, so iteration continues correctly even when a task is concurrently being migrated. This race is hard to hit in practice without instrumentation, but it can be reproduced by artificially slowing down cgroup_procs_show(). For example, on an Android device a temporary /sys/kernel/cgroup/cgroup_test knob can be added to inject a delay into cgroup_procs_show(), and then: 1) Spawn three long-running tasks (PIDs 101, 102, 103). 2) Create a test cgroup and move the tasks into it. 3) Enable a large delay via /sys/kernel/cgroup/cgroup_test. 4) In one shell, read cgroup.procs from the test cgroup. 5) Within the delay window, in another shell migrate PID 102 by writing it to a different cgroup.procs file. Under this setup, cgroup.procs can intermittently show only PID 101 while skipping PID 103. Once the migration completes, reading the file again shows all tasks as expected. Note that this change does not allow removing the existing css_set_skip_task_iters() call in css_set_move_task(). The new call in cgroup_migrate_add_task() only handles iterators that are racing with migration while the task is still on cset->tasks. Iterators may also start after the task has been moved to cset->mg_tasks. If we dropped css_set_skip_task_iters() from css_set_move_task(), such iterators could keep task_pos pointing to a migrating task, causing css_task_iter_advance() to malfunction on the destination css_set, up to and including crashes or infinite loops. The race window between migration and iteration is very small, and css_task_iter is not on a hot path. In the worst case, when an iterator is positioned on the first thread of the migrating process, cgroup_migrate_add_task() may have to skip multiple tasks via css_set_skip_task_iters(). However, this only happens when migration and iteration actually race, so the performance impact is negligible compared to the correctness fix provided here.

In the Linux kernel, the following vulnerability has been resolved: md/bitmap: fix GPF in write_page caused by resize race A General Protection Fault occurs in write_page() during array resize: RIP: 0010:write_page+0x22b/0x3c0 [md_mod] This is a use-after-free race between bitmap_daemon_work() and __bitmap_resize(). The daemon iterates over `bitmap->storage.filemap` without locking, while the resize path frees that storage via md_bitmap_file_unmap(). `quiesce()` does not stop the md thread, allowing concurrent access to freed pages. Fix by holding `mddev->bitmap_info.mutex` during the bitmap update.

In the Linux kernel, the following vulnerability has been resolved: io_uring/zcrx: fix user_ref race between scrub and refill paths The io_zcrx_put_niov_uref() function uses a non-atomic check-then-decrement pattern (atomic_read followed by separate atomic_dec) to manipulate user_refs. This is serialized against other callers by rq_lock, but io_zcrx_scrub() modifies the same counter with atomic_xchg() WITHOUT holding rq_lock. On SMP systems, the following race exists: CPU0 (refill, holds rq_lock) CPU1 (scrub, no rq_lock) put_niov_uref: atomic_read(uref) - 1 // window opens atomic_xchg(uref, 0) - 1 return_niov_freelist(niov) [PUSH #1] // window closes atomic_dec(uref) - wraps to -1 returns true return_niov(niov) return_niov_freelist(niov) [PUSH #2: DOUBLE-FREE] The same niov is pushed to the freelist twice, causing free_count to exceed nr_iovs. Subsequent freelist pushes then perform an out-of-bounds write (a u32 value) past the kvmalloc'd freelist array into the adjacent slab object. Fix this by replacing the non-atomic read-then-dec in io_zcrx_put_niov_uref() with an atomic_try_cmpxchg loop that atomically tests and decrements user_refs. This makes the operation safe against concurrent atomic_xchg from scrub without requiring scrub to acquire rq_lock. [pavel: removed a warning and a comment]

In the Linux kernel, the following vulnerability has been resolved: scsi: ufs: core: Flush exception handling work when RPM level is zero Ensure that the exception event handling work is explicitly flushed during suspend when the runtime power management level is set to UFS_PM_LVL_0. When the RPM level is zero, the device power mode and link state both remain active. Previously, the UFS core driver bypassed flushing exception event handling jobs in this configuration. This created a race condition where the driver could attempt to access the host controller to handle an exception after the system had already entered a deep power-down state, resulting in a system crash. Explicitly flush this work and disable auto BKOPs before the suspend callback proceeds. This guarantees that pending exception tasks complete and prevents illegal hardware access during the power-down sequence.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix race between DIM disable and net_dim() There's a race between disabling DIM and NAPI callbacks using the dim pointer on the RQ or SQ. If NAPI checks the DIM state bit and sees it still set, it assumes `rq->dim` or `sq->dim` is valid. But if DIM gets disabled right after that check, the pointer might already be set to NULL, leading to a NULL pointer dereference in net_dim(). Fix this by calling `synchronize_net()` before freeing the DIM context. This ensures all in-progress NAPI callbacks are finished before the pointer is cleared. Kernel log: BUG: kernel NULL pointer dereference, address: 0000000000000000 ... RIP: 0010:net_dim+0x23/0x190 ... Call Trace: <TASK> ? __die+0x20/0x60 ? page_fault_oops+0x150/0x3e0 ? common_interrupt+0xf/0xa0 ? sysvec_call_function_single+0xb/0x90 ? exc_page_fault+0x74/0x130 ? asm_exc_page_fault+0x22/0x30 ? net_dim+0x23/0x190 ? mlx5e_poll_ico_cq+0x41/0x6f0 [mlx5_core] ? sysvec_apic_timer_interrupt+0xb/0x90 mlx5e_handle_rx_dim+0x92/0xd0 [mlx5_core] mlx5e_napi_poll+0x2cd/0xac0 [mlx5_core] ? mlx5e_poll_ico_cq+0xe5/0x6f0 [mlx5_core] busy_poll_stop+0xa2/0x200 ? mlx5e_napi_poll+0x1d9/0xac0 [mlx5_core] ? mlx5e_trigger_irq+0x130/0x130 [mlx5_core] __napi_busy_loop+0x345/0x3b0 ? sysvec_call_function_single+0xb/0x90 ? asm_sysvec_call_function_single+0x16/0x20 ? sysvec_apic_timer_interrupt+0xb/0x90 ? pcpu_free_area+0x1e4/0x2e0 napi_busy_loop+0x11/0x20 xsk_recvmsg+0x10c/0x130 sock_recvmsg+0x44/0x70 __sys_recvfrom+0xbc/0x130 ? __schedule+0x398/0x890 __x64_sys_recvfrom+0x20/0x30 do_syscall_64+0x4c/0x100 entry_SYSCALL_64_after_hwframe+0x4b/0x53 ... ---[ end trace 0000000000000000 ]--- ... ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]---

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: u_ether: Fix race between gether_disconnect and eth_stop A race condition between gether_disconnect() and eth_stop() leads to a NULL pointer dereference. Specifically, if eth_stop() is triggered concurrently while gether_disconnect() is tearing down the endpoints, eth_stop() attempts to access the cleared endpoint descriptor, causing the following NPE: Unable to handle kernel NULL pointer dereference Call trace: __dwc3_gadget_ep_enable+0x60/0x788 dwc3_gadget_ep_enable+0x70/0xe4 usb_ep_enable+0x60/0x15c eth_stop+0xb8/0x108 Because eth_stop() crashes while holding the dev->lock, the thread running gether_disconnect() fails to acquire the same lock and spins forever, resulting in a hardlockup: Core - Debugging Information for Hardlockup core(7) Call trace: queued_spin_lock_slowpath+0x94/0x488 _raw_spin_lock+0x64/0x6c gether_disconnect+0x19c/0x1e8 ncm_set_alt+0x68/0x1a0 composite_setup+0x6a0/0xc50 The root cause is that the clearing of dev->port_usb in gether_disconnect() is delayed until the end of the function. Move the clearing of dev->port_usb to the very beginning of gether_disconnect() while holding dev->lock. This cuts off the link immediately, ensuring eth_stop() will see dev->port_usb as NULL and safely bail out.

In the Linux kernel, the following vulnerability has been resolved: mm/pagewalk: fix race between concurrent split and refault The splitting of a PUD entry in walk_pud_range() can race with a concurrent thread refaulting the PUD leaf entry causing it to try walking a PMD range that has disappeared. An example and reproduction of this is to try reading numa_maps of a process while VFIO-PCI is setting up DMA (specifically the vfio_pin_pages_remote call) on a large BAR for that process. This will trigger a kernel BUG: vfio-pci 0000:03:00.0: enabling device (0000 -> 0002) BUG: unable to handle page fault for address: ffffa23980000000 PGD 0 P4D 0 Oops: Oops: 0000 [#1] SMP NOPTI ... RIP: 0010:walk_pgd_range+0x3b5/0x7a0 Code: 8d 43 ff 48 89 44 24 28 4d 89 ce 4d 8d a7 00 00 20 00 48 8b 4c 24 28 49 81 e4 00 00 e0 ff 49 8d 44 24 ff 48 39 c8 4c 0f 43 e3 <49> f7 06 9f ff ff ff 75 3b 48 8b 44 24 20 48 8b 40 28 48 85 c0 74 RSP: 0018:ffffac23e1ecf808 EFLAGS: 00010287 RAX: 00007f44c01fffff RBX: 00007f4500000000 RCX: 00007f44ffffffff RDX: 0000000000000000 RSI: 000ffffffffff000 RDI: ffffffff93378fe0 RBP: ffffac23e1ecf918 R08: 0000000000000004 R09: ffffa23980000000 R10: 0000000000000020 R11: 0000000000000004 R12: 00007f44c0200000 R13: 00007f44c0000000 R14: ffffa23980000000 R15: 00007f44c0000000 FS: 00007fe884739580(0000) GS:ffff9b7d7a9c0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffa23980000000 CR3: 000000c0650e2005 CR4: 0000000000770ef0 PKRU: 55555554 Call Trace: <TASK> __walk_page_range+0x195/0x1b0 walk_page_vma+0x62/0xc0 show_numa_map+0x12b/0x3b0 seq_read_iter+0x297/0x440 seq_read+0x11d/0x140 vfs_read+0xc2/0x340 ksys_read+0x5f/0xe0 do_syscall_64+0x68/0x130 ? get_page_from_freelist+0x5c2/0x17e0 ? mas_store_prealloc+0x17e/0x360 ? vma_set_page_prot+0x4c/0xa0 ? __alloc_pages_noprof+0x14e/0x2d0 ? __mod_memcg_lruvec_state+0x8d/0x140 ? __lruvec_stat_mod_folio+0x76/0xb0 ? __folio_mod_stat+0x26/0x80 ? do_anonymous_page+0x705/0x900 ? __handle_mm_fault+0xa8d/0x1000 ? __count_memcg_events+0x53/0xf0 ? handle_mm_fault+0xa5/0x360 ? do_user_addr_fault+0x342/0x640 ? arch_exit_to_user_mode_prepare.constprop.0+0x16/0xa0 ? irqentry_exit_to_user_mode+0x24/0x100 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7fe88464f47e Code: c0 e9 b6 fe ff ff 50 48 8d 3d be 07 0b 00 e8 69 01 02 00 66 0f 1f 84 00 00 00 00 00 64 8b 04 25 18 00 00 00 85 c0 75 14 0f 05 <48> 3d 00 f0 ff ff 77 5a c3 66 0f 1f 84 00 00 00 00 00 48 83 ec 28 RSP: 002b:00007ffe6cd9a9b8 EFLAGS: 00000246 ORIG_RAX: 0000000000000000 RAX: ffffffffffffffda RBX: 0000000000020000 RCX: 00007fe88464f47e RDX: 0000000000020000 RSI: 00007fe884543000 RDI: 0000000000000003 RBP: 00007fe884543000 R08: 00007fe884542010 R09: 0000000000000000 R10: fffffffffffffbc5 R11: 0000000000000246 R12: 0000000000000000 R13: 0000000000000003 R14: 0000000000020000 R15: 0000000000020000 </TASK> Fix this by validating the PUD entry in walk_pmd_range() using a stable snapshot (pudp_get()). If the PUD is not present or is a leaf, retry the walk via ACTION_AGAIN instead of descending further. This mirrors the retry logic in walk_pte_range(), which lets walk_pmd_range() retry if the PTE is not being got by pte_offset_map_lock().

In the Linux kernel, the following vulnerability has been resolved: iommu/amd/pgtbl: Fix possible race while increase page table level The AMD IOMMU host page table implementation supports dynamic page table levels (up to 6 levels), starting with a 3-level configuration that expands based on IOVA address. The kernel maintains a root pointer and current page table level to enable proper page table walks in alloc_pte()/fetch_pte() operations. The IOMMU IOVA allocator initially starts with 32-bit address and onces its exhuasted it switches to 64-bit address (max address is determined based on IOMMU and device DMA capability). To support larger IOVA, AMD IOMMU driver increases page table level. But in unmap path (iommu_v1_unmap_pages()), fetch_pte() reads pgtable->[root/mode] without lock. So its possible that in exteme corner case, when increase_address_space() is updating pgtable->[root/mode], fetch_pte() reads wrong page table level (pgtable->mode). It does compare the value with level encoded in page table and returns NULL. This will result is iommu_unmap ops to fail and upper layer may retry/log WARN_ON. CPU 0 CPU 1 ------ ------ map pages unmap pages alloc_pte() -> increase_address_space() iommu_v1_unmap_pages() -> fetch_pte() pgtable->root = pte (new root value) READ pgtable->[mode/root] Reads new root, old mode Updates mode (pgtable->mode += 1) Since Page table level updates are infrequent and already synchronized with a spinlock, implement seqcount to enable lock-free read operations on the read path.

In the Linux kernel, the following vulnerability has been resolved: media: i2c: tc358743: Fix crash in the probe error path when using polling If an error occurs in the probe() function, we should remove the polling timer that was alarmed earlier, otherwise the timer is called with arguments that are already freed, which results in a crash. ------------[ cut here ]------------ WARNING: CPU: 3 PID: 0 at kernel/time/timer.c:1830 __run_timers+0x244/0x268 Modules linked in: CPU: 3 UID: 0 PID: 0 Comm: swapper/3 Not tainted 6.11.0 #226 Hardware name: Diasom DS-RK3568-SOM-EVB (DT) pstate: 804000c9 (Nzcv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : __run_timers+0x244/0x268 lr : __run_timers+0x1d4/0x268 sp : ffffff80eff2baf0 x29: ffffff80eff2bb50 x28: 7fffffffffffffff x27: ffffff80eff2bb00 x26: ffffffc080f669c0 x25: ffffff80efef6bf0 x24: ffffff80eff2bb00 x23: 0000000000000000 x22: dead000000000122 x21: 0000000000000000 x20: ffffff80efef6b80 x19: ffffff80041c8bf8 x18: ffffffffffffffff x17: ffffffc06f146000 x16: ffffff80eff27dc0 x15: 000000000000003e x14: 0000000000000000 x13: 00000000000054da x12: 0000000000000000 x11: 00000000000639c0 x10: 000000000000000c x9 : 0000000000000009 x8 : ffffff80eff2cb40 x7 : ffffff80eff2cb40 x6 : ffffff8002bee480 x5 : ffffffc080cb2220 x4 : ffffffc080cb2150 x3 : 00000000000f4240 x2 : 0000000000000102 x1 : ffffff80eff2bb00 x0 : ffffff80041c8bf0 Call trace:  __run_timers+0x244/0x268  timer_expire_remote+0x50/0x68  tmigr_handle_remote+0x388/0x39c  run_timer_softirq+0x38/0x44  handle_softirqs+0x138/0x298  __do_softirq+0x14/0x20  ____do_softirq+0x10/0x1c  call_on_irq_stack+0x24/0x4c  do_softirq_own_stack+0x1c/0x2c  irq_exit_rcu+0x9c/0xcc  el1_interrupt+0x48/0xc0  el1h_64_irq_handler+0x18/0x24  el1h_64_irq+0x7c/0x80  default_idle_call+0x34/0x68  do_idle+0x23c/0x294  cpu_startup_entry+0x38/0x3c  secondary_start_kernel+0x128/0x160  __secondary_switched+0xb8/0xbc ---[ end trace 0000000000000000 ]---

In the Linux kernel, the following vulnerability has been resolved: gpiolib: fix race condition for gdev->srcu If two drivers were calling gpiochip_add_data_with_key(), one may be traversing the srcu-protected list in gpio_name_to_desc(), meanwhile other has just added its gdev in gpiodev_add_to_list_unlocked(). This creates a non-mutexed and non-protected timeframe, when one instance is dereferencing and using &gdev->srcu, before the other has initialized it, resulting in crash: [ 4.935481] Unable to handle kernel paging request at virtual address ffff800272bcc000 [ 4.943396] Mem abort info: [ 4.943400] ESR = 0x0000000096000005 [ 4.943403] EC = 0x25: DABT (current EL), IL = 32 bits [ 4.943407] SET = 0, FnV = 0 [ 4.943410] EA = 0, S1PTW = 0 [ 4.943413] FSC = 0x05: level 1 translation fault [ 4.943416] Data abort info: [ 4.943418] ISV = 0, ISS = 0x00000005, ISS2 = 0x00000000 [ 4.946220] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 4.955261] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 4.955268] swapper pgtable: 4k pages, 48-bit VAs, pgdp=0000000038e6c000 [ 4.961449] [ffff800272bcc000] pgd=0000000000000000 [ 4.969203] , p4d=1000000039739003 [ 4.979730] , pud=0000000000000000 [ 4.980210] phandle (CPU): 0x0000005e, phandle (BE): 0x5e000000 for node "reset" [ 4.991736] Internal error: Oops: 0000000096000005 [#1] PREEMPT SMP ... [ 5.121359] pc : __srcu_read_lock+0x44/0x98 [ 5.131091] lr : gpio_name_to_desc+0x60/0x1a0 [ 5.153671] sp : ffff8000833bb430 [ 5.298440] [ 5.298443] Call trace: [ 5.298445] __srcu_read_lock+0x44/0x98 [ 5.309484] gpio_name_to_desc+0x60/0x1a0 [ 5.320692] gpiochip_add_data_with_key+0x488/0xf00 5.946419] ---[ end trace 0000000000000000 ]--- Move initialization code for gdev fields before it is added to gpio_devices, with adjacent initialization code. Adjust goto statements to reflect modified order of operations [Bartosz: fixed a build issue, removed stray newline]

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Prevent concurrent access to IPSec ASO context The query or updating IPSec offload object is through Access ASO WQE. The driver uses a single mlx5e_ipsec_aso struct for each PF, which contains a shared DMA-mapped context for all ASO operations. A race condition exists because the ASO spinlock is released before the hardware has finished processing WQE. If a second operation is initiated immediately after, it overwrites the shared context in the DMA area. When the first operation's completion is processed later, it reads this corrupted context, leading to unexpected behavior and incorrect results. This commit fixes the race by introducing a private context within each IPSec offload object. The shared ASO context is now copied to this private context while the ASO spinlock is held. Subsequent processing uses this saved, per-object context, ensuring its integrity is maintained.

In the Linux kernel, the following vulnerability has been resolved: soc: fsl: qbman: fix race condition in qman_destroy_fq When QMAN_FQ_FLAG_DYNAMIC_FQID is set, there's a race condition between fq_table[fq->idx] state and freeing/allocating from the pool and WARN_ON(fq_table[fq->idx]) in qman_create_fq() gets triggered. Indeed, we can have: Thread A Thread B qman_destroy_fq() qman_create_fq() qman_release_fqid() qman_shutdown_fq() gen_pool_free() -- At this point, the fqid is available again -- qman_alloc_fqid() -- so, we can get the just-freed fqid in thread B -- fq->fqid = fqid; fq->idx = fqid * 2; WARN_ON(fq_table[fq->idx]); fq_table[fq->idx] = fq; fq_table[fq->idx] = NULL; And adding some logs between qman_release_fqid() and fq_table[fq->idx] = NULL makes the WARN_ON() trigger a lot more. To prevent that, ensure that fq_table[fq->idx] is set to NULL before gen_pool_free() is called by using smp_wmb().

In the Linux kernel, the following vulnerability has been resolved: comedi: dt2815: add hardware detection to prevent crash The dt2815 driver crashes when attached to I/O ports without actual hardware present. This occurs because syzkaller or users can attach the driver to arbitrary I/O addresses via COMEDI_DEVCONFIG ioctl. When no hardware exists at the specified port, inb() operations return 0xff (floating bus), but outb() operations can trigger page faults due to undefined behavior, especially under race conditions: BUG: unable to handle page fault for address: 000000007fffff90 #PF: supervisor write access in kernel mode #PF: error_code(0x0002) - not-present page RIP: 0010:dt2815_attach+0x6e0/0x1110 Add hardware detection by reading the status register before attempting any write operations. If the read returns 0xff, assume no hardware is present and fail the attach with -ENODEV. This prevents crashes from outb() operations on non-existent hardware.

In the Linux kernel, the following vulnerability has been resolved: firewire: core: fix race condition against transaction list The list of transaction is enumerated without acquiring card lock when processing AR response event. This causes a race condition bug when processing AT request completion event concurrently. This commit fixes the bug by put timer start for split transaction expiration into the scope of lock. The value of jiffies in card structure is referred before acquiring the lock.

In the Linux kernel, the following vulnerability has been resolved: cxl: Fix race of nvdimm_bus object when creating nvdimm objects Found issue during running of cxl-translate.sh unit test. Adding a 3s sleep right before the test seems to make the issue reproduce fairly consistently. The cxl_translate module has dependency on cxl_acpi and causes orphaned nvdimm objects to reprobe after cxl_acpi is removed. The nvdimm_bus object is registered by the cxl_nvb object when cxl_acpi_probe() is called. With the nvdimm_bus object missing, __nd_device_register() will trigger NULL pointer dereference when accessing the dev->parent that points to &nvdimm_bus->dev. [ 192.884510] BUG: kernel NULL pointer dereference, address: 000000000000006c [ 192.895383] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS edk2-20250812-19.fc42 08/12/2025 [ 192.897721] Workqueue: cxl_port cxl_bus_rescan_queue [cxl_core] [ 192.899459] RIP: 0010:kobject_get+0xc/0x90 [ 192.924871] Call Trace: [ 192.925959] <TASK> [ 192.926976] ? pm_runtime_init+0xb9/0xe0 [ 192.929712] __nd_device_register.part.0+0x4d/0xc0 [libnvdimm] [ 192.933314] __nvdimm_create+0x206/0x290 [libnvdimm] [ 192.936662] cxl_nvdimm_probe+0x119/0x1d0 [cxl_pmem] [ 192.940245] cxl_bus_probe+0x1a/0x60 [cxl_core] [ 192.943349] really_probe+0xde/0x380 This patch also relies on the previous change where devm_cxl_add_nvdimm_bridge() is called from drivers/cxl/pmem.c instead of drivers/cxl/core.c to ensure the dependency of cxl_acpi on cxl_pmem. 1. Set probe_type of cxl_nvb to PROBE_FORCE_SYNCHRONOUS to ensure the driver is probed synchronously when add_device() is called. 2. Add a check in __devm_cxl_add_nvdimm_bridge() to ensure that the cxl_nvb driver is attached during cxl_acpi_probe(). 3. Take the cxl_root uport_dev lock and the cxl_nvb->dev lock in devm_cxl_add_nvdimm() before checking nvdimm_bus is valid. 4. Set cxl_nvdimm flag to CXL_NVD_F_INVALIDATED so cxl_nvdimm_probe() will exit with -EBUSY. The removal of cxl_nvdimm devices should prevent any orphaned devices from probing once the nvdimm_bus is gone. [ dj: Fixed 0-day reported kdoc issue. ] [ dj: Fix cxl_nvb reference leak on error. Gregory (kreview-0811365) ]

In the Linux kernel, the following vulnerability has been resolved: i2c: designware: amdisp: Fix resume-probe race condition issue Identified resume-probe race condition in kernel v7.0 with the commit 38fa29b01a6a ("i2c: designware: Combine the init functions"),but this issue existed from the beginning though not detected. The amdisp i2c device requires ISP to be in power-on state for probe to succeed. To meet this requirement, this device is added to genpd to control ISP power using runtime PM. The pm_runtime_get_sync() called before i2c_dw_probe() triggers PM resume, which powers on ISP and also invokes the amdisp i2c runtime resume before the probe completes resulting in this race condition and a NULL dereferencing issue in v7.0 Fix this race condition by using the genpd APIs directly during probe: - Call dev_pm_genpd_resume() to Power ON ISP before probe - Call dev_pm_genpd_suspend() to Power OFF ISP after probe - Set the device to suspended state with pm_runtime_set_suspended() - Enable runtime PM only after the device is fully initialized

In the Linux kernel, the following vulnerability has been resolved: PM: runtime: Fix a race condition related to device removal The following code in pm_runtime_work() may dereference the dev->parent pointer after the parent device has been freed: /* Maybe the parent is now able to suspend. */ if (parent && !parent->power.ignore_children) { spin_unlock(&dev->power.lock); spin_lock(&parent->power.lock); rpm_idle(parent, RPM_ASYNC); spin_unlock(&parent->power.lock); spin_lock(&dev->power.lock); } Fix this by inserting a flush_work() call in pm_runtime_remove(). Without this patch blktest block/001 triggers the following complaint sporadically: BUG: KASAN: slab-use-after-free in lock_acquire+0x70/0x160 Read of size 1 at addr ffff88812bef7198 by task kworker/u553:1/3081 Workqueue: pm pm_runtime_work Call Trace: <TASK> dump_stack_lvl+0x61/0x80 print_address_description.constprop.0+0x8b/0x310 print_report+0xfd/0x1d7 kasan_report+0xd8/0x1d0 __kasan_check_byte+0x42/0x60 lock_acquire.part.0+0x38/0x230 lock_acquire+0x70/0x160 _raw_spin_lock+0x36/0x50 rpm_suspend+0xc6a/0xfe0 rpm_idle+0x578/0x770 pm_runtime_work+0xee/0x120 process_one_work+0xde3/0x1410 worker_thread+0x5eb/0xfe0 kthread+0x37b/0x480 ret_from_fork+0x6cb/0x920 ret_from_fork_asm+0x11/0x20 </TASK> Allocated by task 4314: kasan_save_stack+0x2a/0x50 kasan_save_track+0x18/0x40 kasan_save_alloc_info+0x3d/0x50 __kasan_kmalloc+0xa0/0xb0 __kmalloc_noprof+0x311/0x990 scsi_alloc_target+0x122/0xb60 [scsi_mod] __scsi_scan_target+0x101/0x460 [scsi_mod] scsi_scan_channel+0x179/0x1c0 [scsi_mod] scsi_scan_host_selected+0x259/0x2d0 [scsi_mod] store_scan+0x2d2/0x390 [scsi_mod] dev_attr_store+0x43/0x80 sysfs_kf_write+0xde/0x140 kernfs_fop_write_iter+0x3ef/0x670 vfs_write+0x506/0x1470 ksys_write+0xfd/0x230 __x64_sys_write+0x76/0xc0 x64_sys_call+0x213/0x1810 do_syscall_64+0xee/0xfc0 entry_SYSCALL_64_after_hwframe+0x4b/0x53 Freed by task 4314: kasan_save_stack+0x2a/0x50 kasan_save_track+0x18/0x40 kasan_save_free_info+0x3f/0x50 __kasan_slab_free+0x67/0x80 kfree+0x225/0x6c0 scsi_target_dev_release+0x3d/0x60 [scsi_mod] device_release+0xa3/0x220 kobject_cleanup+0x105/0x3a0 kobject_put+0x72/0xd0 put_device+0x17/0x20 scsi_device_dev_release+0xacf/0x12c0 [scsi_mod] device_release+0xa3/0x220 kobject_cleanup+0x105/0x3a0 kobject_put+0x72/0xd0 put_device+0x17/0x20 scsi_device_put+0x7f/0xc0 [scsi_mod] sdev_store_delete+0xa5/0x120 [scsi_mod] dev_attr_store+0x43/0x80 sysfs_kf_write+0xde/0x140 kernfs_fop_write_iter+0x3ef/0x670 vfs_write+0x506/0x1470 ksys_write+0xfd/0x230 __x64_sys_write+0x76/0xc0 x64_sys_call+0x213/0x1810

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix race in cpumap on PREEMPT_RT On PREEMPT_RT kernels, the per-CPU xdp_bulk_queue (bq) can be accessed concurrently by multiple preemptible tasks on the same CPU. The original code assumes bq_enqueue() and __cpu_map_flush() run atomically with respect to each other on the same CPU, relying on local_bh_disable() to prevent preemption. However, on PREEMPT_RT, local_bh_disable() only calls migrate_disable() (when PREEMPT_RT_NEEDS_BH_LOCK is not set) and does not disable preemption, which allows CFS scheduling to preempt a task during bq_flush_to_queue(), enabling another task on the same CPU to enter bq_enqueue() and operate on the same per-CPU bq concurrently. This leads to several races: 1. Double __list_del_clearprev(): after bq->count is reset in bq_flush_to_queue(), a preempting task can call bq_enqueue() -> bq_flush_to_queue() on the same bq when bq->count reaches CPU_MAP_BULK_SIZE. Both tasks then call __list_del_clearprev() on the same bq->flush_node, the second call dereferences the prev pointer that was already set to NULL by the first. 2. bq->count and bq->q[] races: concurrent bq_enqueue() can corrupt the packet queue while bq_flush_to_queue() is processing it. The race between task A (__cpu_map_flush -> bq_flush_to_queue) and task B (bq_enqueue -> bq_flush_to_queue) on the same CPU: Task A (xdp_do_flush) Task B (cpu_map_enqueue) ---------------------- ------------------------ bq_flush_to_queue(bq) spin_lock(&q->producer_lock) /* flush bq->q[] to ptr_ring */ bq->count = 0 spin_unlock(&q->producer_lock) bq_enqueue(rcpu, xdpf) <-- CFS preempts Task A --> bq->q[bq->count++] = xdpf /* ... more enqueues until full ... */ bq_flush_to_queue(bq) spin_lock(&q->producer_lock) /* flush to ptr_ring */ spin_unlock(&q->producer_lock) __list_del_clearprev(flush_node) /* sets flush_node.prev = NULL */ <-- Task A resumes --> __list_del_clearprev(flush_node) flush_node.prev->next = ... /* prev is NULL -> kernel oops */ Fix this by adding a local_lock_t to xdp_bulk_queue and acquiring it in bq_enqueue() and __cpu_map_flush(). These paths already run under local_bh_disable(), so use local_lock_nested_bh() which on non-RT is a pure annotation with no overhead, and on PREEMPT_RT provides a per-CPU sleeping lock that serializes access to the bq. To reproduce, insert an mdelay(100) between bq->count = 0 and __list_del_clearprev() in bq_flush_to_queue(), then run reproducer provided by syzkaller.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix race condition during IPSec ESN update In IPSec full offload mode, the device reports an ESN (Extended Sequence Number) wrap event to the driver. The driver validates this event by querying the IPSec ASO and checking that the esn_event_arm field is 0x0, which indicates an event has occurred. After handling the event, the driver must re-arm the context by setting esn_event_arm back to 0x1. A race condition exists in this handling path. After validating the event, the driver calls mlx5_accel_esp_modify_xfrm() to update the kernel's xfrm state. This function temporarily releases and re-acquires the xfrm state lock. So, need to acknowledge the event first by setting esn_event_arm to 0x1. This prevents the driver from reprocessing the same ESN update if the hardware sends events for other reason. Since the next ESN update only occurs after nearly 2^31 packets are received, there's no risk of missing an update, as it will happen long after this handling has finished. Processing the event twice causes the ESN high-order bits (esn_msb) to be incremented incorrectly. The driver then programs the hardware with this invalid ESN state, which leads to anti-replay failures and a complete halt of IPSec traffic. Fix this by re-arming the ESN event immediately after it is validated, before calling mlx5_accel_esp_modify_xfrm(). This ensures that any spurious, duplicate events are correctly ignored, closing the race window.

In the Linux kernel, the following vulnerability has been resolved: spi: tegra210-quad: Protect curr_xfer check in IRQ handler Now that all other accesses to curr_xfer are done under the lock, protect the curr_xfer NULL check in tegra_qspi_isr_thread() with the spinlock. Without this protection, the following race can occur: CPU0 (ISR thread) CPU1 (timeout path) ---------------- ------------------- if (!tqspi->curr_xfer) // sees non-NULL spin_lock() tqspi->curr_xfer = NULL spin_unlock() handle_*_xfer() spin_lock() t = tqspi->curr_xfer // NULL! ... t->len ... // NULL dereference! With this patch, all curr_xfer accesses are now properly synchronized. Although all accesses to curr_xfer are done under the lock, in tegra_qspi_isr_thread() it checks for NULL, releases the lock and reacquires it later in handle_cpu_based_xfer()/handle_dma_based_xfer(). There is a potential for an update in between, which could cause a NULL pointer dereference. To handle this, add a NULL check inside the handlers after acquiring the lock. This ensures that if the timeout path has already cleared curr_xfer, the handler will safely return without dereferencing the NULL pointer.

In the Linux kernel, the following vulnerability has been resolved: rxrpc: Fix data-race warning and potential load/store tearing Fix the following: BUG: KCSAN: data-race in rxrpc_peer_keepalive_worker / rxrpc_send_data_packet which is reporting an issue with the reads and writes to ->last_tx_at in: conn->peer->last_tx_at = ktime_get_seconds(); and: keepalive_at = peer->last_tx_at + RXRPC_KEEPALIVE_TIME; The lockless accesses to these to values aren't actually a problem as the read only needs an approximate time of last transmission for the purposes of deciding whether or not the transmission of a keepalive packet is warranted yet. Also, as ->last_tx_at is a 64-bit value, tearing can occur on a 32-bit arch. Fix both of these by switching to an unsigned int for ->last_tx_at and only storing the LSW of the time64_t. It can then be reconstructed at need provided no more than 68 years has elapsed since the last transmission.

In the Linux kernel, the following vulnerability has been resolved: mptcp: fix race in mptcp_pm_nl_flush_addrs_doit() syzbot and Eulgyu Kim reported crashes in mptcp_pm_nl_get_local_id() and/or mptcp_pm_nl_is_backup() Root cause is list_splice_init() in mptcp_pm_nl_flush_addrs_doit() which is not RCU ready. list_splice_init_rcu() can not be called here while holding pernet->lock spinlock. Many thanks to Eulgyu Kim for providing a repro and testing our patches.

In the Linux kernel, the following vulnerability has been resolved: regmap: Fix race condition in hwspinlock irqsave routine Previously, the address of the shared member '&map->spinlock_flags' was passed directly to 'hwspin_lock_timeout_irqsave'. This creates a race condition where multiple contexts contending for the lock could overwrite the shared flags variable, potentially corrupting the state for the current lock owner. Fix this by using a local stack variable 'flags' to store the IRQ state temporarily.

In the Linux kernel, the following vulnerability has been resolved: drm/imagination: Synchronize interrupts before suspending the GPU The runtime PM suspend callback doesn't know whether the IRQ handler is in progress on a different CPU core and doesn't wait for it to finish. Depending on timing, the IRQ handler could be running while the GPU is suspended, leading to kernel crashes when trying to access GPU registers. See example signature below. In a power off sequence initiated by the runtime PM suspend callback, wait for any IRQ handlers in progress on other CPU cores to finish, by calling synchronize_irq(). At the same time, remove the runtime PM resume/put calls in the threaded IRQ handler. On top of not being the right approach to begin with, and being at the wrong place as they should have wrapped all GPU register accesses, the driver would hit a deadlock between synchronize_irq() being called from a runtime PM suspend callback, holding the device power lock, and the resume callback requiring the same. Example crash signature on a TI AM68 SK platform: [ 337.241218] SError Interrupt on CPU0, code 0x00000000bf000000 -- SError [ 337.241239] CPU: 0 UID: 0 PID: 112 Comm: irq/234-gpu Tainted: G M 6.17.7-B2C-00005-g9c7bbe4ea16c #2 PREEMPT [ 337.241246] Tainted: [M]=MACHINE_CHECK [ 337.241249] Hardware name: Texas Instruments AM68 SK (DT) [ 337.241252] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 337.241256] pc : pvr_riscv_irq_pending+0xc/0x24 [ 337.241277] lr : pvr_device_irq_thread_handler+0x64/0x310 [ 337.241282] sp : ffff800085b0bd30 [ 337.241284] x29: ffff800085b0bd50 x28: ffff0008070d9eab x27: ffff800083a5ce10 [ 337.241291] x26: ffff000806e48f80 x25: ffff0008070d9eac x24: 0000000000000000 [ 337.241296] x23: ffff0008068e9bf0 x22: ffff0008068e9bd0 x21: ffff800085b0bd30 [ 337.241301] x20: ffff0008070d9e00 x19: ffff0008068e9000 x18: 0000000000000001 [ 337.241305] x17: 637365645f656c70 x16: 0000000000000000 x15: ffff000b7df9ff40 [ 337.241310] x14: 0000a585fe3c0d0e x13: 000000999704f060 x12: 000000000002771a [ 337.241314] x11: 00000000000000c0 x10: 0000000000000af0 x9 : ffff800085b0bd00 [ 337.241318] x8 : ffff0008071175d0 x7 : 000000000000b955 x6 : 0000000000000003 [ 337.241323] x5 : 0000000000000000 x4 : 0000000000000002 x3 : 0000000000000000 [ 337.241327] x2 : ffff800080e39d20 x1 : ffff800080e3fc48 x0 : 0000000000000000 [ 337.241333] Kernel panic - not syncing: Asynchronous SError Interrupt [ 337.241337] CPU: 0 UID: 0 PID: 112 Comm: irq/234-gpu Tainted: G M 6.17.7-B2C-00005-g9c7bbe4ea16c #2 PREEMPT [ 337.241342] Tainted: [M]=MACHINE_CHECK [ 337.241343] Hardware name: Texas Instruments AM68 SK (DT) [ 337.241345] Call trace: [ 337.241348] show_stack+0x18/0x24 (C) [ 337.241357] dump_stack_lvl+0x60/0x80 [ 337.241364] dump_stack+0x18/0x24 [ 337.241368] vpanic+0x124/0x2ec [ 337.241373] abort+0x0/0x4 [ 337.241377] add_taint+0x0/0xbc [ 337.241384] arm64_serror_panic+0x70/0x80 [ 337.241389] do_serror+0x3c/0x74 [ 337.241392] el1h_64_error_handler+0x30/0x48 [ 337.241400] el1h_64_error+0x6c/0x70 [ 337.241404] pvr_riscv_irq_pending+0xc/0x24 (P) [ 337.241410] irq_thread_fn+0x2c/0xb0 [ 337.241416] irq_thread+0x170/0x334 [ 337.241421] kthread+0x12c/0x210 [ 337.241428] ret_from_fork+0x10/0x20 [ 337.241434] SMP: stopping secondary CPUs [ 337.241451] Kernel Offset: disabled [ 337.241453] CPU features: 0x040000,02002800,20002001,0400421b [ 337.241456] Memory Limit: none [ 337.457921] ---[ end Kernel panic - not syncing: Asynchronous SError Interrupt ]---

In the Linux kernel, the following vulnerability has been resolved: dst: fix races in rt6_uncached_list_del() and rt_del_uncached_list() syzbot was able to crash the kernel in rt6_uncached_list_flush_dev() in an interesting way [1] Crash happens in list_del_init()/INIT_LIST_HEAD() while writing list->prev, while the prior write on list->next went well. static inline void INIT_LIST_HEAD(struct list_head *list) { WRITE_ONCE(list->next, list); // This went well WRITE_ONCE(list->prev, list); // Crash, @list has been freed. } Issue here is that rt6_uncached_list_del() did not attempt to lock ul->lock, as list_empty(&rt->dst.rt_uncached) returned true because the WRITE_ONCE(list->next, list) happened on the other CPU. We might use list_del_init_careful() and list_empty_careful(), or make sure rt6_uncached_list_del() always grabs the spinlock whenever rt->dst.rt_uncached_list has been set. A similar fix is neeed for IPv4. [1] BUG: KASAN: slab-use-after-free in INIT_LIST_HEAD include/linux/list.h:46 [inline] BUG: KASAN: slab-use-after-free in list_del_init include/linux/list.h:296 [inline] BUG: KASAN: slab-use-after-free in rt6_uncached_list_flush_dev net/ipv6/route.c:191 [inline] BUG: KASAN: slab-use-after-free in rt6_disable_ip+0x633/0x730 net/ipv6/route.c:5020 Write of size 8 at addr ffff8880294cfa78 by task kworker/u8:14/3450 CPU: 0 UID: 0 PID: 3450 Comm: kworker/u8:14 Tainted: G L syzkaller #0 PREEMPT_{RT,(full)} Tainted: [L]=SOFTLOCKUP Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/25/2025 Workqueue: netns cleanup_net Call Trace: <TASK> dump_stack_lvl+0xe8/0x150 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0xca/0x240 mm/kasan/report.c:482 kasan_report+0x118/0x150 mm/kasan/report.c:595 INIT_LIST_HEAD include/linux/list.h:46 [inline] list_del_init include/linux/list.h:296 [inline] rt6_uncached_list_flush_dev net/ipv6/route.c:191 [inline] rt6_disable_ip+0x633/0x730 net/ipv6/route.c:5020 addrconf_ifdown+0x143/0x18a0 net/ipv6/addrconf.c:3853 addrconf_notify+0x1bc/0x1050 net/ipv6/addrconf.c:-1 notifier_call_chain+0x19d/0x3a0 kernel/notifier.c:85 call_netdevice_notifiers_extack net/core/dev.c:2268 [inline] call_netdevice_notifiers net/core/dev.c:2282 [inline] netif_close_many+0x29c/0x410 net/core/dev.c:1785 unregister_netdevice_many_notify+0xb50/0x2330 net/core/dev.c:12353 ops_exit_rtnl_list net/core/net_namespace.c:187 [inline] ops_undo_list+0x3dc/0x990 net/core/net_namespace.c:248 cleanup_net+0x4de/0x7b0 net/core/net_namespace.c:696 process_one_work kernel/workqueue.c:3257 [inline] process_scheduled_works+0xad1/0x1770 kernel/workqueue.c:3340 worker_thread+0x8a0/0xda0 kernel/workqueue.c:3421 kthread+0x711/0x8a0 kernel/kthread.c:463 ret_from_fork+0x510/0xa50 arch/x86/kernel/process.c:158 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:246 </TASK> Allocated by task 803: kasan_save_stack mm/kasan/common.c:57 [inline] kasan_save_track+0x3e/0x80 mm/kasan/common.c:78 unpoison_slab_object mm/kasan/common.c:340 [inline] __kasan_slab_alloc+0x6c/0x80 mm/kasan/common.c:366 kasan_slab_alloc include/linux/kasan.h:253 [inline] slab_post_alloc_hook mm/slub.c:4953 [inline] slab_alloc_node mm/slub.c:5263 [inline] kmem_cache_alloc_noprof+0x18d/0x6c0 mm/slub.c:5270 dst_alloc+0x105/0x170 net/core/dst.c:89 ip6_dst_alloc net/ipv6/route.c:342 [inline] icmp6_dst_alloc+0x75/0x460 net/ipv6/route.c:3333 mld_sendpack+0x683/0xe60 net/ipv6/mcast.c:1844 mld_send_cr net/ipv6/mcast.c:2154 [inline] mld_ifc_work+0x83e/0xd60 net/ipv6/mcast.c:2693 process_one_work kernel/workqueue.c:3257 [inline] process_scheduled_works+0xad1/0x1770 kernel/workqueue.c:3340 worker_thread+0x8a0/0xda0 kernel/workqueue.c:3421 kthread+0x711/0x8a0 kernel/kthread.c:463 ret_from_fork+0x510/0xa50 arch/x86/kernel/process.c:158 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entr ---truncated---

In the Linux kernel, the following vulnerability has been resolved: net: dsa: improve shutdown sequence Alexander Sverdlin presents 2 problems during shutdown with the lan9303 driver. One is specific to lan9303 and the other just happens to reproduce there. The first problem is that lan9303 is unique among DSA drivers in that it calls dev_get_drvdata() at "arbitrary runtime" (not probe, not shutdown, not remove): phy_state_machine() -> ... -> dsa_user_phy_read() -> ds->ops->phy_read() -> lan9303_phy_read() -> chip->ops->phy_read() -> lan9303_mdio_phy_read() -> dev_get_drvdata() But we never stop the phy_state_machine(), so it may continue to run after dsa_switch_shutdown(). Our common pattern in all DSA drivers is to set drvdata to NULL to suppress the remove() method that may come afterwards. But in this case it will result in an NPD. The second problem is that the way in which we set dp->conduit->dsa_ptr = NULL; is concurrent with receive packet processing. dsa_switch_rcv() checks once whether dev->dsa_ptr is NULL, but afterwards, rather than continuing to use that non-NULL value, dev->dsa_ptr is dereferenced again and again without NULL checks: dsa_conduit_find_user() and many other places. In between dereferences, there is no locking to ensure that what was valid once continues to be valid. Both problems have the common aspect that closing the conduit interface solves them. In the first case, dev_close(conduit) triggers the NETDEV_GOING_DOWN event in dsa_user_netdevice_event() which closes user ports as well. dsa_port_disable_rt() calls phylink_stop(), which synchronously stops the phylink state machine, and ds->ops->phy_read() will thus no longer call into the driver after this point. In the second case, dev_close(conduit) should do this, as per Documentation/networking/driver.rst: | Quiescence | ---------- | | After the ndo_stop routine has been called, the hardware must | not receive or transmit any data. All in flight packets must | be aborted. If necessary, poll or wait for completion of | any reset commands. So it should be sufficient to ensure that later, when we zeroize conduit->dsa_ptr, there will be no concurrent dsa_switch_rcv() call on this conduit. The addition of the netif_device_detach() function is to ensure that ioctls, rtnetlinks and ethtool requests on the user ports no longer propagate down to the driver - we're no longer prepared to handle them. The race condition actually did not exist when commit 0650bf52b31f ("net: dsa: be compatible with masters which unregister on shutdown") first introduced dsa_switch_shutdown(). It was created later, when we stopped unregistering the user interfaces from a bad spot, and we just replaced that sequence with a racy zeroization of conduit->dsa_ptr (one which doesn't ensure that the interfaces aren't up).

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix a data-race around bpf_jit_limit. While reading bpf_jit_limit, it can be changed concurrently via sysctl, WRITE_ONCE() in __do_proc_doulongvec_minmax(). The size of bpf_jit_limit is long, so we need to add a paired READ_ONCE() to avoid load-tearing.

In the Linux kernel, the following vulnerability has been resolved: ice: Fix race condition during interface enslave Commit 5dbbbd01cbba83 ("ice: Avoid RTNL lock when re-creating auxiliary device") changes a process of re-creation of aux device so ice_plug_aux_dev() is called from ice_service_task() context. This unfortunately opens a race window that can result in dead-lock when interface has left LAG and immediately enters LAG again. Reproducer: ``` #!/bin/sh ip link add lag0 type bond mode 1 miimon 100 ip link set lag0 for n in {1..10}; do echo Cycle: $n ip link set ens7f0 master lag0 sleep 1 ip link set ens7f0 nomaster done ``` This results in: [20976.208697] Workqueue: ice ice_service_task [ice] [20976.213422] Call Trace: [20976.215871] __schedule+0x2d1/0x830 [20976.219364] schedule+0x35/0xa0 [20976.222510] schedule_preempt_disabled+0xa/0x10 [20976.227043] __mutex_lock.isra.7+0x310/0x420 [20976.235071] enum_all_gids_of_dev_cb+0x1c/0x100 [ib_core] [20976.251215] ib_enum_roce_netdev+0xa4/0xe0 [ib_core] [20976.256192] ib_cache_setup_one+0x33/0xa0 [ib_core] [20976.261079] ib_register_device+0x40d/0x580 [ib_core] [20976.266139] irdma_ib_register_device+0x129/0x250 [irdma] [20976.281409] irdma_probe+0x2c1/0x360 [irdma] [20976.285691] auxiliary_bus_probe+0x45/0x70 [20976.289790] really_probe+0x1f2/0x480 [20976.298509] driver_probe_device+0x49/0xc0 [20976.302609] bus_for_each_drv+0x79/0xc0 [20976.306448] __device_attach+0xdc/0x160 [20976.310286] bus_probe_device+0x9d/0xb0 [20976.314128] device_add+0x43c/0x890 [20976.321287] __auxiliary_device_add+0x43/0x60 [20976.325644] ice_plug_aux_dev+0xb2/0x100 [ice] [20976.330109] ice_service_task+0xd0c/0xed0 [ice] [20976.342591] process_one_work+0x1a7/0x360 [20976.350536] worker_thread+0x30/0x390 [20976.358128] kthread+0x10a/0x120 [20976.365547] ret_from_fork+0x1f/0x40 ... [20976.438030] task:ip state:D stack: 0 pid:213658 ppid:213627 flags:0x00004084 [20976.446469] Call Trace: [20976.448921] __schedule+0x2d1/0x830 [20976.452414] schedule+0x35/0xa0 [20976.455559] schedule_preempt_disabled+0xa/0x10 [20976.460090] __mutex_lock.isra.7+0x310/0x420 [20976.464364] device_del+0x36/0x3c0 [20976.467772] ice_unplug_aux_dev+0x1a/0x40 [ice] [20976.472313] ice_lag_event_handler+0x2a2/0x520 [ice] [20976.477288] notifier_call_chain+0x47/0x70 [20976.481386] __netdev_upper_dev_link+0x18b/0x280 [20976.489845] bond_enslave+0xe05/0x1790 [bonding] [20976.494475] do_setlink+0x336/0xf50 [20976.502517] __rtnl_newlink+0x529/0x8b0 [20976.543441] rtnl_newlink+0x43/0x60 [20976.546934] rtnetlink_rcv_msg+0x2b1/0x360 [20976.559238] netlink_rcv_skb+0x4c/0x120 [20976.563079] netlink_unicast+0x196/0x230 [20976.567005] netlink_sendmsg+0x204/0x3d0 [20976.570930] sock_sendmsg+0x4c/0x50 [20976.574423] ____sys_sendmsg+0x1eb/0x250 [20976.586807] ___sys_sendmsg+0x7c/0xc0 [20976.606353] __sys_sendmsg+0x57/0xa0 [20976.609930] do_syscall_64+0x5b/0x1a0 [20976.613598] entry_SYSCALL_64_after_hwframe+0x65/0xca 1. Command 'ip link ... set nomaster' causes that ice_plug_aux_dev() is called from ice_service_task() context, aux device is created and associated device->lock is taken. 2. Command 'ip link ... set master...' calls ice's notifier under RTNL lock and that notifier calls ice_unplug_aux_dev(). That function tries to take aux device->lock but this is already taken by ice_plug_aux_dev() in step 1 3. Later ice_plug_aux_dev() tries to take RTNL lock but this is already taken in step 2 4. Dead-lock The patch fixes this issue by following changes: - Bit ICE_FLAG_PLUG_AUX_DEV is kept to be set during ice_plug_aux_dev() call in ice_service_task() - The bit is checked in ice_clear_rdma_cap() and only if it is not set then ice_unplug_aux_dev() is called. If it is set (in other words plugging of aux device was requested and ice_plug_aux_dev() is potentially running) then the function only clears the ---truncated---

In the Linux kernel, the following vulnerability has been resolved: ath11k: fix netdev open race Make sure to allocate resources needed before registering the device. This specifically avoids having a racing open() trigger a BUG_ON() in mod_timer() when ath11k_mac_op_start() is called before the mon_reap_timer as been set up. I did not see this issue with next-20220310, but I hit it on every probe with next-20220511. Perhaps some timing changed in between. Here's the backtrace: [ 51.346947] kernel BUG at kernel/time/timer.c:990! [ 51.346958] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ... [ 51.578225] Call trace: [ 51.583293] __mod_timer+0x298/0x390 [ 51.589518] mod_timer+0x14/0x20 [ 51.595368] ath11k_mac_op_start+0x41c/0x4a0 [ath11k] [ 51.603165] drv_start+0x38/0x60 [mac80211] [ 51.610110] ieee80211_do_open+0x29c/0x7d0 [mac80211] [ 51.617945] ieee80211_open+0x60/0xb0 [mac80211] [ 51.625311] __dev_open+0x100/0x1c0 [ 51.631420] __dev_change_flags+0x194/0x210 [ 51.638214] dev_change_flags+0x24/0x70 [ 51.644646] do_setlink+0x228/0xdb0 [ 51.650723] __rtnl_newlink+0x460/0x830 [ 51.657162] rtnl_newlink+0x4c/0x80 [ 51.663229] rtnetlink_rcv_msg+0x124/0x390 [ 51.669917] netlink_rcv_skb+0x58/0x130 [ 51.676314] rtnetlink_rcv+0x18/0x30 [ 51.682460] netlink_unicast+0x250/0x310 [ 51.688960] netlink_sendmsg+0x19c/0x3e0 [ 51.695458] ____sys_sendmsg+0x220/0x290 [ 51.701938] ___sys_sendmsg+0x7c/0xc0 [ 51.708148] __sys_sendmsg+0x68/0xd0 [ 51.714254] __arm64_sys_sendmsg+0x28/0x40 [ 51.720900] invoke_syscall+0x48/0x120 Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3

In the Linux kernel, the following vulnerability has been resolved: scsi: target: iscsi: Fix a race condition between login_work and the login thread In case a malicious initiator sends some random data immediately after a login PDU; the iscsi_target_sk_data_ready() callback will schedule the login_work and, at the same time, the negotiation may end without clearing the LOGIN_FLAGS_INITIAL_PDU flag (because no additional PDU exchanges are required to complete the login). The login has been completed but the login_work function will find the LOGIN_FLAGS_INITIAL_PDU flag set and will never stop from rescheduling itself; at this point, if the initiator drops the connection, the iscsit_conn structure will be freed, login_work will dereference a released socket structure and the kernel crashes. BUG: kernel NULL pointer dereference, address: 0000000000000230 PF: supervisor write access in kernel mode PF: error_code(0x0002) - not-present page Workqueue: events iscsi_target_do_login_rx [iscsi_target_mod] RIP: 0010:_raw_read_lock_bh+0x15/0x30 Call trace: iscsi_target_do_login_rx+0x75/0x3f0 [iscsi_target_mod] process_one_work+0x1e8/0x3c0 Fix this bug by forcing login_work to stop after the login has been completed and the socket callbacks have been restored. Add a comment to clearify the return values of iscsi_target_do_login()

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: f_fs: Remove WARN_ON in functionfs_bind This commit addresses an issue related to below kernel panic where panic_on_warn is enabled. It is caused by the unnecessary use of WARN_ON in functionsfs_bind, which easily leads to the following scenarios. 1.adb_write in adbd 2. UDC write via configfs ================= ===================== ->usb_ffs_open_thread() ->UDC write ->open_functionfs() ->configfs_write_iter() ->adb_open() ->gadget_dev_desc_UDC_store() ->adb_write() ->usb_gadget_register_driver_owner ->driver_register() ->StartMonitor() ->bus_add_driver() ->adb_read() ->gadget_bind_driver() <times-out without BIND event> ->configfs_composite_bind() ->usb_add_function() ->open_functionfs() ->ffs_func_bind() ->adb_open() ->functionfs_bind() <ffs->state !=FFS_ACTIVE> The adb_open, adb_read, and adb_write operations are invoked from the daemon, but trying to bind the function is a process that is invoked by UDC write through configfs, which opens up the possibility of a race condition between the two paths. In this race scenario, the kernel panic occurs due to the WARN_ON from functionfs_bind when panic_on_warn is enabled. This commit fixes the kernel panic by removing the unnecessary WARN_ON. Kernel panic - not syncing: kernel: panic_on_warn set ... [ 14.542395] Call trace: [ 14.542464] ffs_func_bind+0x1c8/0x14a8 [ 14.542468] usb_add_function+0xcc/0x1f0 [ 14.542473] configfs_composite_bind+0x468/0x588 [ 14.542478] gadget_bind_driver+0x108/0x27c [ 14.542483] really_probe+0x190/0x374 [ 14.542488] __driver_probe_device+0xa0/0x12c [ 14.542492] driver_probe_device+0x3c/0x220 [ 14.542498] __driver_attach+0x11c/0x1fc [ 14.542502] bus_for_each_dev+0x104/0x160 [ 14.542506] driver_attach+0x24/0x34 [ 14.542510] bus_add_driver+0x154/0x270 [ 14.542514] driver_register+0x68/0x104 [ 14.542518] usb_gadget_register_driver_owner+0x48/0xf4 [ 14.542523] gadget_dev_desc_UDC_store+0xf8/0x144 [ 14.542526] configfs_write_iter+0xf0/0x138

In the Linux kernel, the following vulnerability has been resolved: fgraph: Add READ_ONCE() when accessing fgraph_array[] In __ftrace_return_to_handler(), a loop iterates over the fgraph_array[] elements, which are fgraph_ops. The loop checks if an element is a fgraph_stub to prevent using a fgraph_stub afterward. However, if the compiler reloads fgraph_array[] after this check, it might race with an update to fgraph_array[] that introduces a fgraph_stub. This could result in the stub being processed, but the stub contains a null "func_hash" field, leading to a NULL pointer dereference. To ensure that the gops compared against the fgraph_stub matches the gops processed later, add a READ_ONCE(). A similar patch appears in commit 63a8dfb ("function_graph: Add READ_ONCE() when accessing fgraph_array[]").

In the Linux kernel, the following vulnerability has been resolved: drm/xe/guc_submit: fix race around suspend_pending Currently in some testcases we can trigger: xe 0000:03:00.0: [drm] Assertion `exec_queue_destroyed(q)` failed! .... WARNING: CPU: 18 PID: 2640 at drivers/gpu/drm/xe/xe_guc_submit.c:1826 xe_guc_sched_done_handler+0xa54/0xef0 [xe] xe 0000:03:00.0: [drm] *ERROR* GT1: DEREGISTER_DONE: Unexpected engine state 0x00a1, guc_id=57 Looking at a snippet of corresponding ftrace for this GuC id we can see: 162.673311: xe_sched_msg_add: dev=0000:03:00.0, gt=1 guc_id=57, opcode=3 162.673317: xe_sched_msg_recv: dev=0000:03:00.0, gt=1 guc_id=57, opcode=3 162.673319: xe_exec_queue_scheduling_disable: dev=0000:03:00.0, 1:0x2, gt=1, width=1, guc_id=57, guc_state=0x29, flags=0x0 162.674089: xe_exec_queue_kill: dev=0000:03:00.0, 1:0x2, gt=1, width=1, guc_id=57, guc_state=0x29, flags=0x0 162.674108: xe_exec_queue_close: dev=0000:03:00.0, 1:0x2, gt=1, width=1, guc_id=57, guc_state=0xa9, flags=0x0 162.674488: xe_exec_queue_scheduling_done: dev=0000:03:00.0, 1:0x2, gt=1, width=1, guc_id=57, guc_state=0xa9, flags=0x0 162.678452: xe_exec_queue_deregister: dev=0000:03:00.0, 1:0x2, gt=1, width=1, guc_id=57, guc_state=0xa1, flags=0x0 It looks like we try to suspend the queue (opcode=3), setting suspend_pending and triggering a disable_scheduling. The user then closes the queue. However the close will also forcefully signal the suspend fence after killing the queue, later when the G2H response for disable_scheduling comes back we have now cleared suspend_pending when signalling the suspend fence, so the disable_scheduling now incorrectly tries to also deregister the queue. This leads to warnings since the queue has yet to even be marked for destruction. We also seem to trigger errors later with trying to double unregister the same queue. To fix this tweak the ordering when handling the response to ensure we don't race with a disable_scheduling that didn't actually intend to perform an unregister. The destruction path should now also correctly wait for any pending_disable before marking as destroyed. (cherry picked from commit f161809b362f027b6d72bd998e47f8f0bad60a2e)

In the Linux kernel, the following vulnerability has been resolved: accel/ivpu: Prevent recovery invocation during probe and resume Refactor IPC send and receive functions to allow correct handling of operations that should not trigger a recovery process. Expose ivpu_send_receive_internal(), which is now utilized by the D0i3 entry, DCT initialization, and HWS initialization functions. These functions have been modified to return error codes gracefully, rather than initiating recovery. The updated functions are invoked within ivpu_probe() and ivpu_resume(), ensuring that any errors encountered during these stages result in a proper teardown or shutdown sequence. The previous approach of triggering recovery within these functions could lead to a race condition, potentially causing undefined behavior and kernel crashes due to null pointer dereferences.

In the Linux kernel, the following vulnerability has been resolved: iommu/arm-smmu: Defer probe of clients after smmu device bound Null pointer dereference occurs due to a race between smmu driver probe and client driver probe, when of_dma_configure() for client is called after the iommu_device_register() for smmu driver probe has executed but before the driver_bound() for smmu driver has been called. Following is how the race occurs: T1:Smmu device probe T2: Client device probe really_probe() arm_smmu_device_probe() iommu_device_register() really_probe() platform_dma_configure() of_dma_configure() of_dma_configure_id() of_iommu_configure() iommu_probe_device() iommu_init_device() arm_smmu_probe_device() arm_smmu_get_by_fwnode() driver_find_device_by_fwnode() driver_find_device() next_device() klist_next() /* null ptr assigned to smmu */ /* null ptr dereference while smmu->streamid_mask */ driver_bound() klist_add_tail() When this null smmu pointer is dereferenced later in arm_smmu_probe_device, the device crashes. Fix this by deferring the probe of the client device until the smmu device has bound to the arm smmu driver. [will: Add comment]

In the Linux kernel, the following vulnerability has been resolved: net: fix data-races around sk->sk_forward_alloc Syzkaller reported this warning: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 16 at net/ipv4/af_inet.c:156 inet_sock_destruct+0x1c5/0x1e0 Modules linked in: CPU: 0 UID: 0 PID: 16 Comm: ksoftirqd/0 Not tainted 6.12.0-rc5 #26 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 RIP: 0010:inet_sock_destruct+0x1c5/0x1e0 Code: 24 12 4c 89 e2 5b 48 c7 c7 98 ec bb 82 41 5c e9 d1 18 17 ff 4c 89 e6 5b 48 c7 c7 d0 ec bb 82 41 5c e9 bf 18 17 ff 0f 0b eb 83 <0f> 0b eb 97 0f 0b eb 87 0f 0b e9 68 ff ff ff 66 66 2e 0f 1f 84 00 RSP: 0018:ffffc9000008bd90 EFLAGS: 00010206 RAX: 0000000000000300 RBX: ffff88810b172a90 RCX: 0000000000000007 RDX: 0000000000000002 RSI: 0000000000000300 RDI: ffff88810b172a00 RBP: ffff88810b172a00 R08: ffff888104273c00 R09: 0000000000100007 R10: 0000000000020000 R11: 0000000000000006 R12: ffff88810b172a00 R13: 0000000000000004 R14: 0000000000000000 R15: ffff888237c31f78 FS: 0000000000000000(0000) GS:ffff888237c00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007ffc63fecac8 CR3: 000000000342e000 CR4: 00000000000006f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? __warn+0x88/0x130 ? inet_sock_destruct+0x1c5/0x1e0 ? report_bug+0x18e/0x1a0 ? handle_bug+0x53/0x90 ? exc_invalid_op+0x18/0x70 ? asm_exc_invalid_op+0x1a/0x20 ? inet_sock_destruct+0x1c5/0x1e0 __sk_destruct+0x2a/0x200 rcu_do_batch+0x1aa/0x530 ? rcu_do_batch+0x13b/0x530 rcu_core+0x159/0x2f0 handle_softirqs+0xd3/0x2b0 ? __pfx_smpboot_thread_fn+0x10/0x10 run_ksoftirqd+0x25/0x30 smpboot_thread_fn+0xdd/0x1d0 kthread+0xd3/0x100 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x34/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> ---[ end trace 0000000000000000 ]--- Its possible that two threads call tcp_v6_do_rcv()/sk_forward_alloc_add() concurrently when sk->sk_state == TCP_LISTEN with sk->sk_lock unlocked, which triggers a data-race around sk->sk_forward_alloc: tcp_v6_rcv tcp_v6_do_rcv skb_clone_and_charge_r sk_rmem_schedule __sk_mem_schedule sk_forward_alloc_add() skb_set_owner_r sk_mem_charge sk_forward_alloc_add() __kfree_skb skb_release_all skb_release_head_state sock_rfree sk_mem_uncharge sk_forward_alloc_add() sk_mem_reclaim // set local var reclaimable __sk_mem_reclaim sk_forward_alloc_add() In this syzkaller testcase, two threads call tcp_v6_do_rcv() with skb->truesize=768, the sk_forward_alloc changes like this: (cpu 1) | (cpu 2) | sk_forward_alloc ... | ... | 0 __sk_mem_schedule() | | +4096 = 4096 | __sk_mem_schedule() | +4096 = 8192 sk_mem_charge() | | -768 = 7424 | sk_mem_charge() | -768 = 6656 ... | ... | sk_mem_uncharge() | | +768 = 7424 reclaimable=7424 | | | sk_mem_uncharge() | +768 = 8192 | reclaimable=8192 | __sk_mem_reclaim() | | -4096 = 4096 | __sk_mem_reclaim() | -8192 = -4096 != 0 The skb_clone_and_charge_r() should not be called in tcp_v6_do_rcv() when sk->sk_state is TCP_LISTEN, it happens later in tcp_v6_syn_recv_sock(). Fix the same issue in dccp_v6_do_rcv().

In the Linux kernel, the following vulnerability has been resolved: i40e: fix race condition by adding filter's intermediate sync state Fix a race condition in the i40e driver that leads to MAC/VLAN filters becoming corrupted and leaking. Address the issue that occurs under heavy load when multiple threads are concurrently modifying MAC/VLAN filters by setting mac and port VLAN. 1. Thread T0 allocates a filter in i40e_add_filter() within i40e_ndo_set_vf_port_vlan(). 2. Thread T1 concurrently frees the filter in __i40e_del_filter() within i40e_ndo_set_vf_mac(). 3. Subsequently, i40e_service_task() calls i40e_sync_vsi_filters(), which refers to the already freed filter memory, causing corruption. Reproduction steps: 1. Spawn multiple VFs. 2. Apply a concurrent heavy load by running parallel operations to change MAC addresses on the VFs and change port VLANs on the host. 3. Observe errors in dmesg: "Error I40E_AQ_RC_ENOSPC adding RX filters on VF XX, please set promiscuous on manually for VF XX". Exact code for stable reproduction Intel can't open-source now. The fix involves implementing a new intermediate filter state, I40E_FILTER_NEW_SYNC, for the time when a filter is on a tmp_add_list. These filters cannot be deleted from the hash list directly but must be removed using the full process.

In the Linux kernel, the following vulnerability has been resolved: rcu/kvfree: Fix data-race in __mod_timer / kvfree_call_rcu KCSAN reports a data race when access the krcp->monitor_work.timer.expires variable in the schedule_delayed_monitor_work() function: <snip> BUG: KCSAN: data-race in __mod_timer / kvfree_call_rcu read to 0xffff888237d1cce8 of 8 bytes by task 10149 on cpu 1: schedule_delayed_monitor_work kernel/rcu/tree.c:3520 [inline] kvfree_call_rcu+0x3b8/0x510 kernel/rcu/tree.c:3839 trie_update_elem+0x47c/0x620 kernel/bpf/lpm_trie.c:441 bpf_map_update_value+0x324/0x350 kernel/bpf/syscall.c:203 generic_map_update_batch+0x401/0x520 kernel/bpf/syscall.c:1849 bpf_map_do_batch+0x28c/0x3f0 kernel/bpf/syscall.c:5143 __sys_bpf+0x2e5/0x7a0 __do_sys_bpf kernel/bpf/syscall.c:5741 [inline] __se_sys_bpf kernel/bpf/syscall.c:5739 [inline] __x64_sys_bpf+0x43/0x50 kernel/bpf/syscall.c:5739 x64_sys_call+0x2625/0x2d60 arch/x86/include/generated/asm/syscalls_64.h:322 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xc9/0x1c0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f write to 0xffff888237d1cce8 of 8 bytes by task 56 on cpu 0: __mod_timer+0x578/0x7f0 kernel/time/timer.c:1173 add_timer_global+0x51/0x70 kernel/time/timer.c:1330 __queue_delayed_work+0x127/0x1a0 kernel/workqueue.c:2523 queue_delayed_work_on+0xdf/0x190 kernel/workqueue.c:2552 queue_delayed_work include/linux/workqueue.h:677 [inline] schedule_delayed_monitor_work kernel/rcu/tree.c:3525 [inline] kfree_rcu_monitor+0x5e8/0x660 kernel/rcu/tree.c:3643 process_one_work kernel/workqueue.c:3229 [inline] process_scheduled_works+0x483/0x9a0 kernel/workqueue.c:3310 worker_thread+0x51d/0x6f0 kernel/workqueue.c:3391 kthread+0x1d1/0x210 kernel/kthread.c:389 ret_from_fork+0x4b/0x60 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 Reported by Kernel Concurrency Sanitizer on: CPU: 0 UID: 0 PID: 56 Comm: kworker/u8:4 Not tainted 6.12.0-rc2-syzkaller-00050-g5b7c893ed5ed #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 Workqueue: events_unbound kfree_rcu_monitor <snip> kfree_rcu_monitor() rearms the work if a "krcp" has to be still offloaded and this is done without holding krcp->lock, whereas the kvfree_call_rcu() holds it. Fix it by acquiring the "krcp->lock" for kfree_rcu_monitor() so both functions do not race anymore.

In the Linux kernel, the following vulnerability has been resolved: nvme: tcp: avoid race between queue_lock lock and destroy Commit 76d54bf20cdc ("nvme-tcp: don't access released socket during error recovery") added a mutex_lock() call for the queue->queue_lock in nvme_tcp_get_address(). However, the mutex_lock() races with mutex_destroy() in nvme_tcp_free_queue(), and causes the WARN below. DEBUG_LOCKS_WARN_ON(lock->magic != lock) WARNING: CPU: 3 PID: 34077 at kernel/locking/mutex.c:587 __mutex_lock+0xcf0/0x1220 Modules linked in: nvmet_tcp nvmet nvme_tcp nvme_fabrics iw_cm ib_cm ib_core pktcdvd nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip_set nf_tables qrtr sunrpc ppdev 9pnet_virtio 9pnet pcspkr netfs parport_pc parport e1000 i2c_piix4 i2c_smbus loop fuse nfnetlink zram bochs drm_vram_helper drm_ttm_helper ttm drm_kms_helper xfs drm sym53c8xx floppy nvme scsi_transport_spi nvme_core nvme_auth serio_raw ata_generic pata_acpi dm_multipath qemu_fw_cfg [last unloaded: ib_uverbs] CPU: 3 UID: 0 PID: 34077 Comm: udisksd Not tainted 6.11.0-rc7 #319 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014 RIP: 0010:__mutex_lock+0xcf0/0x1220 Code: 08 84 d2 0f 85 c8 04 00 00 8b 15 ef b6 c8 01 85 d2 0f 85 78 f4 ff ff 48 c7 c6 20 93 ee af 48 c7 c7 60 91 ee af e8 f0 a7 6d fd <0f> 0b e9 5e f4 ff ff 48 b8 00 00 00 00 00 fc ff df 4c 89 f2 48 c1 RSP: 0018:ffff88811305f760 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff88812c652058 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000001 RBP: ffff88811305f8b0 R08: 0000000000000001 R09: ffffed1075c36341 R10: ffff8883ae1b1a0b R11: 0000000000010498 R12: 0000000000000000 R13: 0000000000000000 R14: dffffc0000000000 R15: ffff88812c652058 FS: 00007f9713ae4980(0000) GS:ffff8883ae180000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fcd78483c7c CR3: 0000000122c38000 CR4: 00000000000006f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? __warn.cold+0x5b/0x1af ? __mutex_lock+0xcf0/0x1220 ? report_bug+0x1ec/0x390 ? handle_bug+0x3c/0x80 ? exc_invalid_op+0x13/0x40 ? asm_exc_invalid_op+0x16/0x20 ? __mutex_lock+0xcf0/0x1220 ? nvme_tcp_get_address+0xc2/0x1e0 [nvme_tcp] ? __pfx___mutex_lock+0x10/0x10 ? __lock_acquire+0xd6a/0x59e0 ? nvme_tcp_get_address+0xc2/0x1e0 [nvme_tcp] nvme_tcp_get_address+0xc2/0x1e0 [nvme_tcp] ? __pfx_nvme_tcp_get_address+0x10/0x10 [nvme_tcp] nvme_sysfs_show_address+0x81/0xc0 [nvme_core] dev_attr_show+0x42/0x80 ? __asan_memset+0x1f/0x40 sysfs_kf_seq_show+0x1f0/0x370 seq_read_iter+0x2cb/0x1130 ? rw_verify_area+0x3b1/0x590 ? __mutex_lock+0x433/0x1220 vfs_read+0x6a6/0xa20 ? lockdep_hardirqs_on+0x78/0x100 ? __pfx_vfs_read+0x10/0x10 ksys_read+0xf7/0x1d0 ? __pfx_ksys_read+0x10/0x10 ? __x64_sys_openat+0x105/0x1d0 do_syscall_64+0x93/0x180 ? lockdep_hardirqs_on_prepare+0x16d/0x400 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on+0x78/0x100 ? do_syscall_64+0x9f/0x180 ? __pfx_ksys_read+0x10/0x10 ? lockdep_hardirqs_on_prepare+0x16d/0x400 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on+0x78/0x100 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on_prepare+0x16d/0x400 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on+0x78/0x100 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on_prepare+0x16d/0x400 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on+0x78/0x100 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on_prepare+0x16d/0x400 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on+0x78/0x100 ? do_syscall_64+0x9f/0x180 ? do_syscall_64+0x9f/0x180 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7f9713f55cfa Code: 55 48 89 e5 48 83 ec 20 48 89 55 e8 48 89 75 f0 89 7d f8 e8 e8 74 f8 ff 48 8b 55 e8 48 8b 75 f0 4 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: mm: revert "mm: shmem: fix data-race in shmem_getattr()" Revert d949d1d14fa2 ("mm: shmem: fix data-race in shmem_getattr()") as suggested by Chuck [1]. It is causing deadlocks when accessing tmpfs over NFS. As Hugh commented, "added just to silence a syzbot sanitizer splat: added where there has never been any practical problem".

In the Linux kernel, the following vulnerability has been resolved: tracing/timerlat: Fix a race during cpuhp processing There is another found exception that the "timerlat/1" thread was scheduled on CPU0, and lead to timer corruption finally: ``` ODEBUG: init active (active state 0) object: ffff888237c2e108 object type: hrtimer hint: timerlat_irq+0x0/0x220 WARNING: CPU: 0 PID: 426 at lib/debugobjects.c:518 debug_print_object+0x7d/0xb0 Modules linked in: CPU: 0 UID: 0 PID: 426 Comm: timerlat/1 Not tainted 6.11.0-rc7+ #45 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014 RIP: 0010:debug_print_object+0x7d/0xb0 ... Call Trace: <TASK> ? __warn+0x7c/0x110 ? debug_print_object+0x7d/0xb0 ? report_bug+0xf1/0x1d0 ? prb_read_valid+0x17/0x20 ? handle_bug+0x3f/0x70 ? exc_invalid_op+0x13/0x60 ? asm_exc_invalid_op+0x16/0x20 ? debug_print_object+0x7d/0xb0 ? debug_print_object+0x7d/0xb0 ? __pfx_timerlat_irq+0x10/0x10 __debug_object_init+0x110/0x150 hrtimer_init+0x1d/0x60 timerlat_main+0xab/0x2d0 ? __pfx_timerlat_main+0x10/0x10 kthread+0xb7/0xe0 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2d/0x40 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> ``` After tracing the scheduling event, it was discovered that the migration of the "timerlat/1" thread was performed during thread creation. Further analysis confirmed that it is because the CPU online processing for osnoise is implemented through workers, which is asynchronous with the offline processing. When the worker was scheduled to create a thread, the CPU may has already been removed from the cpu_online_mask during the offline process, resulting in the inability to select the right CPU: T1 | T2 [CPUHP_ONLINE] | cpu_device_down() osnoise_hotplug_workfn() | | cpus_write_lock() | takedown_cpu(1) | cpus_write_unlock() [CPUHP_OFFLINE] | cpus_read_lock() | start_kthread(1) | cpus_read_unlock() | To fix this, skip online processing if the CPU is already offline.

In the Linux kernel, the following vulnerability has been resolved: mm/gup: fix memfd_pin_folios alloc race panic If memfd_pin_folios tries to create a hugetlb page, but someone else already did, then folio gets the value -EEXIST here: folio = memfd_alloc_folio(memfd, start_idx); if (IS_ERR(folio)) { ret = PTR_ERR(folio); if (ret != -EEXIST) goto err; then on the next trip through the "while start_idx" loop we panic here: if (folio) { folio_put(folio); To fix, set the folio to NULL on error.