In the Linux kernel, the following vulnerability has been resolved: ath11k: fix netdev open race Make sure to allocate resources needed before registering the device. This specifically avoids having a racing open() trigger a BUG_ON() in mod_timer() when ath11k_mac_op_start() is called before the mon_reap_timer as been set up. I did not see this issue with next-20220310, but I hit it on every probe with next-20220511. Perhaps some timing changed in between. Here's the backtrace: [ 51.346947] kernel BUG at kernel/time/timer.c:990! [ 51.346958] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ... [ 51.578225] Call trace: [ 51.583293] __mod_timer+0x298/0x390 [ 51.589518] mod_timer+0x14/0x20 [ 51.595368] ath11k_mac_op_start+0x41c/0x4a0 [ath11k] [ 51.603165] drv_start+0x38/0x60 [mac80211] [ 51.610110] ieee80211_do_open+0x29c/0x7d0 [mac80211] [ 51.617945] ieee80211_open+0x60/0xb0 [mac80211] [ 51.625311] __dev_open+0x100/0x1c0 [ 51.631420] __dev_change_flags+0x194/0x210 [ 51.638214] dev_change_flags+0x24/0x70 [ 51.644646] do_setlink+0x228/0xdb0 [ 51.650723] __rtnl_newlink+0x460/0x830 [ 51.657162] rtnl_newlink+0x4c/0x80 [ 51.663229] rtnetlink_rcv_msg+0x124/0x390 [ 51.669917] netlink_rcv_skb+0x58/0x130 [ 51.676314] rtnetlink_rcv+0x18/0x30 [ 51.682460] netlink_unicast+0x250/0x310 [ 51.688960] netlink_sendmsg+0x19c/0x3e0 [ 51.695458] ____sys_sendmsg+0x220/0x290 [ 51.701938] ___sys_sendmsg+0x7c/0xc0 [ 51.708148] __sys_sendmsg+0x68/0xd0 [ 51.714254] __arm64_sys_sendmsg+0x28/0x40 [ 51.720900] invoke_syscall+0x48/0x120 Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3

In the Linux kernel, the following vulnerability has been resolved: pinmux: fix race causing mux_owner NULL with active mux_usecount commit 5a3e85c3c397 ("pinmux: Use sequential access to access desc->pinmux data") tried to address the issue when two client of the same gpio calls pinctrl_select_state() for the same functionality, was resulting in NULL pointer issue while accessing desc->mux_owner. However, issue was not completely fixed due to the way it was handled and it can still result in the same NULL pointer. The issue occurs due to the following interleaving: cpu0 (process A) cpu1 (process B) pin_request() { pin_free() { mutex_lock() desc->mux_usecount--; //becomes 0 .. mutex_unlock() mutex_lock(desc->mux) desc->mux_usecount++; // becomes 1 desc->mux_owner = owner; mutex_unlock(desc->mux) mutex_lock(desc->mux) desc->mux_owner = NULL; mutex_unlock(desc->mux) This sequence leads to a state where the pin appears to be in use (`mux_usecount == 1`) but has no owner (`mux_owner == NULL`), which can cause NULL pointer on next pin_request on the same pin. Ensure that updates to mux_usecount and mux_owner are performed atomically under the same lock. Only clear mux_owner when mux_usecount reaches zero and no new owner has been assigned.

In the Linux kernel, the following vulnerability has been resolved: bus: mhi: host: Fix race between unprepare and queue_buf A client driver may use mhi_unprepare_from_transfer() to quiesce incoming data during the client driver's tear down. The client driver might also be processing data at the same time, resulting in a call to mhi_queue_buf() which will invoke mhi_gen_tre(). If mhi_gen_tre() runs after mhi_unprepare_from_transfer() has torn down the channel, a panic will occur due to an invalid dereference leading to a page fault. This occurs because mhi_gen_tre() does not verify the channel state after locking it. Fix this by having mhi_gen_tre() confirm the channel state is valid, or return error to avoid accessing deinitialized data. [mani: added stable tag]

In the Linux kernel, the following vulnerability has been resolved: drm/v3d: Assign job pointer to NULL before signaling the fence In commit e4b5ccd392b9 ("drm/v3d: Ensure job pointer is set to NULL after job completion"), we introduced a change to assign the job pointer to NULL after completing a job, indicating job completion. However, this approach created a race condition between the DRM scheduler workqueue and the IRQ execution thread. As soon as the fence is signaled in the IRQ execution thread, a new job starts to be executed. This results in a race condition where the IRQ execution thread sets the job pointer to NULL simultaneously as the `run_job()` function assigns a new job to the pointer. This race condition can lead to a NULL pointer dereference if the IRQ execution thread sets the job pointer to NULL after `run_job()` assigns it to the new job. When the new job completes and the GPU emits an interrupt, `v3d_irq()` is triggered, potentially causing a crash. [ 466.310099] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000c0 [ 466.318928] Mem abort info: [ 466.321723] ESR = 0x0000000096000005 [ 466.325479] EC = 0x25: DABT (current EL), IL = 32 bits [ 466.330807] SET = 0, FnV = 0 [ 466.333864] EA = 0, S1PTW = 0 [ 466.337010] FSC = 0x05: level 1 translation fault [ 466.341900] Data abort info: [ 466.344783] ISV = 0, ISS = 0x00000005, ISS2 = 0x00000000 [ 466.350285] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 466.355350] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 466.360677] user pgtable: 4k pages, 39-bit VAs, pgdp=0000000089772000 [ 466.367140] [00000000000000c0] pgd=0000000000000000, p4d=0000000000000000, pud=0000000000000000 [ 466.375875] Internal error: Oops: 0000000096000005 [#1] PREEMPT SMP [ 466.382163] Modules linked in: rfcomm snd_seq_dummy snd_hrtimer snd_seq snd_seq_device algif_hash algif_skcipher af_alg bnep binfmt_misc vc4 snd_soc_hdmi_codec drm_display_helper cec brcmfmac_wcc spidev rpivid_hevc(C) drm_client_lib brcmfmac hci_uart drm_dma_helper pisp_be btbcm brcmutil snd_soc_core aes_ce_blk v4l2_mem2mem bluetooth aes_ce_cipher snd_compress videobuf2_dma_contig ghash_ce cfg80211 gf128mul snd_pcm_dmaengine videobuf2_memops ecdh_generic sha2_ce ecc videobuf2_v4l2 snd_pcm v3d sha256_arm64 rfkill videodev snd_timer sha1_ce libaes gpu_sched snd videobuf2_common sha1_generic drm_shmem_helper mc rp1_pio drm_kms_helper raspberrypi_hwmon spi_bcm2835 gpio_keys i2c_brcmstb rp1 raspberrypi_gpiomem rp1_mailbox rp1_adc nvmem_rmem uio_pdrv_genirq uio i2c_dev drm ledtrig_pattern drm_panel_orientation_quirks backlight fuse dm_mod ip_tables x_tables ipv6 [ 466.458429] CPU: 0 UID: 1000 PID: 2008 Comm: chromium Tainted: G C 6.13.0-v8+ #18 [ 466.467336] Tainted: [C]=CRAP [ 466.470306] Hardware name: Raspberry Pi 5 Model B Rev 1.0 (DT) [ 466.476157] pstate: 404000c9 (nZcv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 466.483143] pc : v3d_irq+0x118/0x2e0 [v3d] [ 466.487258] lr : __handle_irq_event_percpu+0x60/0x228 [ 466.492327] sp : ffffffc080003ea0 [ 466.495646] x29: ffffffc080003ea0 x28: ffffff80c0c94200 x27: 0000000000000000 [ 466.502807] x26: ffffffd08dd81d7b x25: ffffff80c0c94200 x24: ffffff8003bdc200 [ 466.509969] x23: 0000000000000001 x22: 00000000000000a7 x21: 0000000000000000 [ 466.517130] x20: ffffff8041bb0000 x19: 0000000000000001 x18: 0000000000000000 [ 466.524291] x17: ffffffafadfb0000 x16: ffffffc080000000 x15: 0000000000000000 [ 466.531452] x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000 [ 466.538613] x11: 0000000000000000 x10: 0000000000000000 x9 : ffffffd08c527eb0 [ 466.545777] x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000000000 [ 466.552941] x5 : ffffffd08c4100d0 x4 : ffffffafadfb0000 x3 : ffffffc080003f70 [ 466.560102] x2 : ffffffc0829e8058 x1 : 0000000000000001 x0 : 0000000000000000 [ 466.567263] Call trace: [ 466.569711] v3d_irq+0x118/0x2e0 [v3d] (P) [ 466. ---truncated---

In the Linux kernel, the following vulnerability has been resolved: RDMA/mlx5: Fix the recovery flow of the UMR QP This patch addresses an issue in the recovery flow of the UMR QP, ensuring tasks do not get stuck, as highlighted by the call trace [1]. During recovery, before transitioning the QP to the RESET state, the software must wait for all outstanding WRs to complete. Failing to do so can cause the firmware to skip sending some flushed CQEs with errors and simply discard them upon the RESET, as per the IB specification. This race condition can result in lost CQEs and tasks becoming stuck. To resolve this, the patch sends a final WR which serves only as a barrier before moving the QP state to RESET. Once a CQE is received for that final WR, it guarantees that no outstanding WRs remain, making it safe to transition the QP to RESET and subsequently back to RTS, restoring proper functionality. Note: For the barrier WR, we simply reuse the failed and ready WR. Since the QP is in an error state, it will only receive IB_WC_WR_FLUSH_ERR. However, as it serves only as a barrier we don't care about its status. [1] INFO: task rdma_resource_l:1922 blocked for more than 120 seconds. Tainted: G W 6.12.0-rc7+ #1626 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. task:rdma_resource_l state:D stack:0 pid:1922 tgid:1922 ppid:1369 flags:0x00004004 Call Trace: <TASK> __schedule+0x420/0xd30 schedule+0x47/0x130 schedule_timeout+0x280/0x300 ? mark_held_locks+0x48/0x80 ? lockdep_hardirqs_on_prepare+0xe5/0x1a0 wait_for_completion+0x75/0x130 mlx5r_umr_post_send_wait+0x3c2/0x5b0 [mlx5_ib] ? __pfx_mlx5r_umr_done+0x10/0x10 [mlx5_ib] mlx5r_umr_revoke_mr+0x93/0xc0 [mlx5_ib] __mlx5_ib_dereg_mr+0x299/0x520 [mlx5_ib] ? _raw_spin_unlock_irq+0x24/0x40 ? wait_for_completion+0xfe/0x130 ? rdma_restrack_put+0x63/0xe0 [ib_core] ib_dereg_mr_user+0x5f/0x120 [ib_core] ? lock_release+0xc6/0x280 destroy_hw_idr_uobject+0x1d/0x60 [ib_uverbs] uverbs_destroy_uobject+0x58/0x1d0 [ib_uverbs] uobj_destroy+0x3f/0x70 [ib_uverbs] ib_uverbs_cmd_verbs+0x3e4/0xbb0 [ib_uverbs] ? __pfx_uverbs_destroy_def_handler+0x10/0x10 [ib_uverbs] ? __lock_acquire+0x64e/0x2080 ? mark_held_locks+0x48/0x80 ? find_held_lock+0x2d/0xa0 ? lock_acquire+0xc1/0x2f0 ? ib_uverbs_ioctl+0xcb/0x170 [ib_uverbs] ? __fget_files+0xc3/0x1b0 ib_uverbs_ioctl+0xe7/0x170 [ib_uverbs] ? ib_uverbs_ioctl+0xcb/0x170 [ib_uverbs] __x64_sys_ioctl+0x1b0/0xa70 do_syscall_64+0x6b/0x140 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7f99c918b17b RSP: 002b:00007ffc766d0468 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 00007ffc766d0578 RCX: 00007f99c918b17b RDX: 00007ffc766d0560 RSI: 00000000c0181b01 RDI: 0000000000000003 RBP: 00007ffc766d0540 R08: 00007f99c8f99010 R09: 000000000000bd7e R10: 00007f99c94c1c70 R11: 0000000000000246 R12: 00007ffc766d0530 R13: 000000000000001c R14: 0000000040246a80 R15: 0000000000000000 </TASK>

A pivot_root race condition in fs/namespace.c in the Linux kernel 4.4.x before 4.4.221, 4.9.x before 4.9.221, 4.14.x before 4.14.178, 4.19.x before 4.19.119, and 5.x before 5.3 allows local users to cause a denial of service (panic) by corrupting a mountpoint reference counter.

In the Linux kernel, the following vulnerability has been resolved: io_uring/zcrx: fix user_ref race between scrub and refill paths The io_zcrx_put_niov_uref() function uses a non-atomic check-then-decrement pattern (atomic_read followed by separate atomic_dec) to manipulate user_refs. This is serialized against other callers by rq_lock, but io_zcrx_scrub() modifies the same counter with atomic_xchg() WITHOUT holding rq_lock. On SMP systems, the following race exists: CPU0 (refill, holds rq_lock) CPU1 (scrub, no rq_lock) put_niov_uref: atomic_read(uref) - 1 // window opens atomic_xchg(uref, 0) - 1 return_niov_freelist(niov) [PUSH #1] // window closes atomic_dec(uref) - wraps to -1 returns true return_niov(niov) return_niov_freelist(niov) [PUSH #2: DOUBLE-FREE] The same niov is pushed to the freelist twice, causing free_count to exceed nr_iovs. Subsequent freelist pushes then perform an out-of-bounds write (a u32 value) past the kvmalloc'd freelist array into the adjacent slab object. Fix this by replacing the non-atomic read-then-dec in io_zcrx_put_niov_uref() with an atomic_try_cmpxchg loop that atomically tests and decrements user_refs. This makes the operation safe against concurrent atomic_xchg from scrub without requiring scrub to acquire rq_lock. [pavel: removed a warning and a comment]

Race condition in the ext4_file_write_iter function in fs/ext4/file.c in the Linux kernel through 3.17 allows local users to cause a denial of service (file unavailability) via a combination of a write action and an F_SETFL fcntl operation for the O_DIRECT flag.

In the Linux kernel, the following vulnerability has been resolved: wifi: rtw89: fix potential race condition between napi_init and napi_enable A race condition can happen if netdev is registered, but NAPI isn't initialized yet, and meanwhile user space starts the netdev that will enable NAPI. Then, it hits BUG_ON(): kernel BUG at net/core/dev.c:6423! invalid opcode: 0000 [#1] PREEMPT SMP NOPTI CPU: 0 PID: 417 Comm: iwd Not tainted 6.2.7-slab-dirty #3 eb0f5a8a9d91 Hardware name: LENOVO 21DL/LNVNB161216, BIOS JPCN20WW(V1.06) 09/20/2022 RIP: 0010:napi_enable+0x3f/0x50 Code: 48 89 c2 48 83 e2 f6 f6 81 89 08 00 00 02 74 0d 48 83 ... RSP: 0018:ffffada1414f3548 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffffa01425802080 RCX: 0000000000000000 RDX: 00000000000002ff RSI: ffffada14e50c614 RDI: ffffa01425808dc0 RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: 0000000000000100 R12: ffffa01425808f58 R13: 0000000000000000 R14: ffffa01423498940 R15: 0000000000000001 FS: 00007f5577c0a740(0000) GS:ffffa0169fc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f5577a19972 CR3: 0000000125a7a000 CR4: 0000000000750ef0 PKRU: 55555554 Call Trace: <TASK> rtw89_pci_ops_start+0x1c/0x70 [rtw89_pci 6cbc75429515c181cbc386478d5cfb32ffc5a0f8] rtw89_core_start+0xbe/0x160 [rtw89_core fe07ecb874820b6d778370d4acb6ef8a37847f22] rtw89_ops_start+0x26/0x40 [rtw89_core fe07ecb874820b6d778370d4acb6ef8a37847f22] drv_start+0x42/0x100 [mac80211 c07fa22af8c3cf3f7d7ab3884ca990784d72e2d2] ieee80211_do_open+0x311/0x7d0 [mac80211 c07fa22af8c3cf3f7d7ab3884ca990784d72e2d2] ieee80211_open+0x6a/0x90 [mac80211 c07fa22af8c3cf3f7d7ab3884ca990784d72e2d2] __dev_open+0xe0/0x180 __dev_change_flags+0x1da/0x250 dev_change_flags+0x26/0x70 do_setlink+0x37c/0x12c0 ? ep_poll_callback+0x246/0x290 ? __nla_validate_parse+0x61/0xd00 ? __wake_up_common_lock+0x8f/0xd0 To fix this, follow Jonas' suggestion to switch the order of these functions and move register netdev to be the last step of PCI probe. Also, correct the error handling of rtw89_core_register_hw().

In the Linux kernel, the following vulnerability has been resolved: net: openvswitch: fix race on port output assume the following setup on a single machine: 1. An openvswitch instance with one bridge and default flows 2. two network namespaces "server" and "client" 3. two ovs interfaces "server" and "client" on the bridge 4. for each ovs interface a veth pair with a matching name and 32 rx and tx queues 5. move the ends of the veth pairs to the respective network namespaces 6. assign ip addresses to each of the veth ends in the namespaces (needs to be the same subnet) 7. start some http server on the server network namespace 8. test if a client in the client namespace can reach the http server when following the actions below the host has a chance of getting a cpu stuck in a infinite loop: 1. send a large amount of parallel requests to the http server (around 3000 curls should work) 2. in parallel delete the network namespace (do not delete interfaces or stop the server, just kill the namespace) there is a low chance that this will cause the below kernel cpu stuck message. If this does not happen just retry. Below there is also the output of bpftrace for the functions mentioned in the output. The series of events happening here is: 1. the network namespace is deleted calling `unregister_netdevice_many_notify` somewhere in the process 2. this sets first `NETREG_UNREGISTERING` on both ends of the veth and then runs `synchronize_net` 3. it then calls `call_netdevice_notifiers` with `NETDEV_UNREGISTER` 4. this is then handled by `dp_device_event` which calls `ovs_netdev_detach_dev` (if a vport is found, which is the case for the veth interface attached to ovs) 5. this removes the rx_handlers of the device but does not prevent packages to be sent to the device 6. `dp_device_event` then queues the vport deletion to work in background as a ovs_lock is needed that we do not hold in the unregistration path 7. `unregister_netdevice_many_notify` continues to call `netdev_unregister_kobject` which sets `real_num_tx_queues` to 0 8. port deletion continues (but details are not relevant for this issue) 9. at some future point the background task deletes the vport If after 7. but before 9. a packet is send to the ovs vport (which is not deleted at this point in time) which forwards it to the `dev_queue_xmit` flow even though the device is unregistering. In `skb_tx_hash` (which is called in the `dev_queue_xmit`) path there is a while loop (if the packet has a rx_queue recorded) that is infinite if `dev->real_num_tx_queues` is zero. To prevent this from happening we update `do_output` to handle devices without carrier the same as if the device is not found (which would be the code path after 9. is done). Additionally we now produce a warning in `skb_tx_hash` if we will hit the infinite loop. bpftrace (first word is function name): __dev_queue_xmit server: real_num_tx_queues: 1, cpu: 2, pid: 28024, tid: 28024, skb_addr: 0xffff9edb6f207000, reg_state: 1 netdev_core_pick_tx server: addr: 0xffff9f0a46d4a000 real_num_tx_queues: 1, cpu: 2, pid: 28024, tid: 28024, skb_addr: 0xffff9edb6f207000, reg_state: 1 dp_device_event server: real_num_tx_queues: 1 cpu 9, pid: 21024, tid: 21024, event 2, reg_state: 1 synchronize_rcu_expedited: cpu 9, pid: 21024, tid: 21024 synchronize_rcu_expedited: cpu 9, pid: 21024, tid: 21024 synchronize_rcu_expedited: cpu 9, pid: 21024, tid: 21024 synchronize_rcu_expedited: cpu 9, pid: 21024, tid: 21024 dp_device_event server: real_num_tx_queues: 1 cpu 9, pid: 21024, tid: 21024, event 6, reg_state: 2 ovs_netdev_detach_dev server: real_num_tx_queues: 1 cpu 9, pid: 21024, tid: 21024, reg_state: 2 netdev_rx_handler_unregister server: real_num_tx_queues: 1, cpu: 9, pid: 21024, tid: 21024, reg_state: 2 synchronize_rcu_expedited: cpu 9, pid: 21024, tid: 21024 netdev_rx_handler_unregister ret server: real_num_tx_queues: 1, cpu: 9, pid: 21024, tid: 21024, reg_state: 2 dp_ ---truncated---

In the Linux kernel, the following vulnerability has been resolved: comedi: dt2815: add hardware detection to prevent crash The dt2815 driver crashes when attached to I/O ports without actual hardware present. This occurs because syzkaller or users can attach the driver to arbitrary I/O addresses via COMEDI_DEVCONFIG ioctl. When no hardware exists at the specified port, inb() operations return 0xff (floating bus), but outb() operations can trigger page faults due to undefined behavior, especially under race conditions: BUG: unable to handle page fault for address: 000000007fffff90 #PF: supervisor write access in kernel mode #PF: error_code(0x0002) - not-present page RIP: 0010:dt2815_attach+0x6e0/0x1110 Add hardware detection by reading the status register before attempting any write operations. If the read returns 0xff, assume no hardware is present and fail the attach with -ENODEV. This prevents crashes from outb() operations on non-existent hardware.

In the Linux kernel, the following vulnerability has been resolved: i2c: designware: amdisp: Fix resume-probe race condition issue Identified resume-probe race condition in kernel v7.0 with the commit 38fa29b01a6a ("i2c: designware: Combine the init functions"),but this issue existed from the beginning though not detected. The amdisp i2c device requires ISP to be in power-on state for probe to succeed. To meet this requirement, this device is added to genpd to control ISP power using runtime PM. The pm_runtime_get_sync() called before i2c_dw_probe() triggers PM resume, which powers on ISP and also invokes the amdisp i2c runtime resume before the probe completes resulting in this race condition and a NULL dereferencing issue in v7.0 Fix this race condition by using the genpd APIs directly during probe: - Call dev_pm_genpd_resume() to Power ON ISP before probe - Call dev_pm_genpd_suspend() to Power OFF ISP after probe - Set the device to suspended state with pm_runtime_set_suspended() - Enable runtime PM only after the device is fully initialized

In the Linux kernel, the following vulnerability has been resolved: mm/pagewalk: fix race between concurrent split and refault The splitting of a PUD entry in walk_pud_range() can race with a concurrent thread refaulting the PUD leaf entry causing it to try walking a PMD range that has disappeared. An example and reproduction of this is to try reading numa_maps of a process while VFIO-PCI is setting up DMA (specifically the vfio_pin_pages_remote call) on a large BAR for that process. This will trigger a kernel BUG: vfio-pci 0000:03:00.0: enabling device (0000 -> 0002) BUG: unable to handle page fault for address: ffffa23980000000 PGD 0 P4D 0 Oops: Oops: 0000 [#1] SMP NOPTI ... RIP: 0010:walk_pgd_range+0x3b5/0x7a0 Code: 8d 43 ff 48 89 44 24 28 4d 89 ce 4d 8d a7 00 00 20 00 48 8b 4c 24 28 49 81 e4 00 00 e0 ff 49 8d 44 24 ff 48 39 c8 4c 0f 43 e3 <49> f7 06 9f ff ff ff 75 3b 48 8b 44 24 20 48 8b 40 28 48 85 c0 74 RSP: 0018:ffffac23e1ecf808 EFLAGS: 00010287 RAX: 00007f44c01fffff RBX: 00007f4500000000 RCX: 00007f44ffffffff RDX: 0000000000000000 RSI: 000ffffffffff000 RDI: ffffffff93378fe0 RBP: ffffac23e1ecf918 R08: 0000000000000004 R09: ffffa23980000000 R10: 0000000000000020 R11: 0000000000000004 R12: 00007f44c0200000 R13: 00007f44c0000000 R14: ffffa23980000000 R15: 00007f44c0000000 FS: 00007fe884739580(0000) GS:ffff9b7d7a9c0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffa23980000000 CR3: 000000c0650e2005 CR4: 0000000000770ef0 PKRU: 55555554 Call Trace: <TASK> __walk_page_range+0x195/0x1b0 walk_page_vma+0x62/0xc0 show_numa_map+0x12b/0x3b0 seq_read_iter+0x297/0x440 seq_read+0x11d/0x140 vfs_read+0xc2/0x340 ksys_read+0x5f/0xe0 do_syscall_64+0x68/0x130 ? get_page_from_freelist+0x5c2/0x17e0 ? mas_store_prealloc+0x17e/0x360 ? vma_set_page_prot+0x4c/0xa0 ? __alloc_pages_noprof+0x14e/0x2d0 ? __mod_memcg_lruvec_state+0x8d/0x140 ? __lruvec_stat_mod_folio+0x76/0xb0 ? __folio_mod_stat+0x26/0x80 ? do_anonymous_page+0x705/0x900 ? __handle_mm_fault+0xa8d/0x1000 ? __count_memcg_events+0x53/0xf0 ? handle_mm_fault+0xa5/0x360 ? do_user_addr_fault+0x342/0x640 ? arch_exit_to_user_mode_prepare.constprop.0+0x16/0xa0 ? irqentry_exit_to_user_mode+0x24/0x100 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7fe88464f47e Code: c0 e9 b6 fe ff ff 50 48 8d 3d be 07 0b 00 e8 69 01 02 00 66 0f 1f 84 00 00 00 00 00 64 8b 04 25 18 00 00 00 85 c0 75 14 0f 05 <48> 3d 00 f0 ff ff 77 5a c3 66 0f 1f 84 00 00 00 00 00 48 83 ec 28 RSP: 002b:00007ffe6cd9a9b8 EFLAGS: 00000246 ORIG_RAX: 0000000000000000 RAX: ffffffffffffffda RBX: 0000000000020000 RCX: 00007fe88464f47e RDX: 0000000000020000 RSI: 00007fe884543000 RDI: 0000000000000003 RBP: 00007fe884543000 R08: 00007fe884542010 R09: 0000000000000000 R10: fffffffffffffbc5 R11: 0000000000000246 R12: 0000000000000000 R13: 0000000000000003 R14: 0000000000020000 R15: 0000000000020000 </TASK> Fix this by validating the PUD entry in walk_pmd_range() using a stable snapshot (pudp_get()). If the PUD is not present or is a leaf, retry the walk via ACTION_AGAIN instead of descending further. This mirrors the retry logic in walk_pte_range(), which lets walk_pmd_range() retry if the PTE is not being got by pte_offset_map_lock().

Race condition in the __kvm_migrate_pit_timer function in arch/x86/kvm/i8254.c in the KVM subsystem in the Linux kernel through 3.17.2 allows guest OS users to cause a denial of service (host OS crash) by leveraging incorrect PIT emulation.

In the Linux kernel, the following vulnerability has been resolved: io-wq: check for wq exit after adding new worker task_work We check IO_WQ_BIT_EXIT before attempting to create a new worker, and wq exit cancels pending work if we have any. But it's possible to have a race between the two, where creation checks exit finding it not set, but we're in the process of exiting. The exit side will cancel pending creation task_work, but there's a gap where we add task_work after we've canceled existing creations at exit time. Fix this by checking the EXIT bit post adding the creation task_work. If it's set, run the same cancelation that exit does.

In the Linux kernel, the following vulnerability has been resolved: s390/qeth: fix deadlock during failing recovery Commit 0b9902c1fcc5 ("s390/qeth: fix deadlock during recovery") removed taking discipline_mutex inside qeth_do_reset(), fixing potential deadlocks. An error path was missed though, that still takes discipline_mutex and thus has the original deadlock potential. Intermittent deadlocks were seen when a qeth channel path is configured offline, causing a race between qeth_do_reset and ccwgroup_remove. Call qeth_set_offline() directly in the qeth_do_reset() error case and then a new variant of ccwgroup_set_offline(), without taking discipline_mutex.

In the Linux kernel, the following vulnerability has been resolved: nfsd: Fix nsfd startup race (again) Commit bd5ae9288d64 ("nfsd: register pernet ops last, unregister first") has re-opened rpc_pipefs_event() race against nfsd_net_id registration (register_pernet_subsys()) which has been fixed by commit bb7ffbf29e76 ("nfsd: fix nsfd startup race triggering BUG_ON"). Restore the order of register_pernet_subsys() vs register_cld_notifier(). Add WARN_ON() to prevent a future regression. Crash info: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000012 CPU: 8 PID: 345 Comm: mount Not tainted 5.4.144-... #1 pc : rpc_pipefs_event+0x54/0x120 [nfsd] lr : rpc_pipefs_event+0x48/0x120 [nfsd] Call trace: rpc_pipefs_event+0x54/0x120 [nfsd] blocking_notifier_call_chain rpc_fill_super get_tree_keyed rpc_fs_get_tree vfs_get_tree do_mount ksys_mount __arm64_sys_mount el0_svc_handler el0_svc

In the Linux kernel, the following vulnerability has been resolved: net/smc: fix kernel panic caused by race of smc_sock A crash occurs when smc_cdc_tx_handler() tries to access smc_sock but smc_release() has already freed it. [ 4570.695099] BUG: unable to handle page fault for address: 000000002eae9e88 [ 4570.696048] #PF: supervisor write access in kernel mode [ 4570.696728] #PF: error_code(0x0002) - not-present page [ 4570.697401] PGD 0 P4D 0 [ 4570.697716] Oops: 0002 [#1] PREEMPT SMP NOPTI [ 4570.698228] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.16.0-rc4+ #111 [ 4570.699013] Hardware name: Alibaba Cloud Alibaba Cloud ECS, BIOS 8c24b4c 04/0 [ 4570.699933] RIP: 0010:_raw_spin_lock+0x1a/0x30 <...> [ 4570.711446] Call Trace: [ 4570.711746] <IRQ> [ 4570.711992] smc_cdc_tx_handler+0x41/0xc0 [ 4570.712470] smc_wr_tx_tasklet_fn+0x213/0x560 [ 4570.712981] ? smc_cdc_tx_dismisser+0x10/0x10 [ 4570.713489] tasklet_action_common.isra.17+0x66/0x140 [ 4570.714083] __do_softirq+0x123/0x2f4 [ 4570.714521] irq_exit_rcu+0xc4/0xf0 [ 4570.714934] common_interrupt+0xba/0xe0 Though smc_cdc_tx_handler() checked the existence of smc connection, smc_release() may have already dismissed and released the smc socket before smc_cdc_tx_handler() further visits it. smc_cdc_tx_handler() |smc_release() if (!conn) | | |smc_cdc_tx_dismiss_slots() | smc_cdc_tx_dismisser() | |sock_put(&smc->sk) <- last sock_put, | smc_sock freed bh_lock_sock(&smc->sk) (panic) | To make sure we won't receive any CDC messages after we free the smc_sock, add a refcount on the smc_connection for inflight CDC message(posted to the QP but haven't received related CQE), and don't release the smc_connection until all the inflight CDC messages haven been done, for both success or failed ones. Using refcount on CDC messages brings another problem: when the link is going to be destroyed, smcr_link_clear() will reset the QP, which then remove all the pending CQEs related to the QP in the CQ. To make sure all the CQEs will always come back so the refcount on the smc_connection can always reach 0, smc_ib_modify_qp_reset() was replaced by smc_ib_modify_qp_error(). And remove the timeout in smc_wr_tx_wait_no_pending_sends() since we need to wait for all pending WQEs done, or we may encounter use-after- free when handling CQEs. For IB device removal routine, we need to wait for all the QPs on that device been destroyed before we can destroy CQs on the device, or the refcount on smc_connection won't reach 0 and smc_sock cannot be released.

In the Linux kernel, the following vulnerability has been resolved: userfaultfd: fix a race between writeprotect and exit_mmap() A race is possible when a process exits, its VMAs are removed by exit_mmap() and at the same time userfaultfd_writeprotect() is called. The race was detected by KASAN on a development kernel, but it appears to be possible on vanilla kernels as well. Use mmget_not_zero() to prevent the race as done in other userfaultfd operations.

In the Linux kernel, the following vulnerability has been resolved: spi: tegra210-quad: Protect curr_xfer check in IRQ handler Now that all other accesses to curr_xfer are done under the lock, protect the curr_xfer NULL check in tegra_qspi_isr_thread() with the spinlock. Without this protection, the following race can occur: CPU0 (ISR thread) CPU1 (timeout path) ---------------- ------------------- if (!tqspi->curr_xfer) // sees non-NULL spin_lock() tqspi->curr_xfer = NULL spin_unlock() handle_*_xfer() spin_lock() t = tqspi->curr_xfer // NULL! ... t->len ... // NULL dereference! With this patch, all curr_xfer accesses are now properly synchronized. Although all accesses to curr_xfer are done under the lock, in tegra_qspi_isr_thread() it checks for NULL, releases the lock and reacquires it later in handle_cpu_based_xfer()/handle_dma_based_xfer(). There is a potential for an update in between, which could cause a NULL pointer dereference. To handle this, add a NULL check inside the handlers after acquiring the lock. This ensures that if the timeout path has already cleared curr_xfer, the handler will safely return without dereferencing the NULL pointer.

In the Linux kernel, the following vulnerability has been resolved: mptcp: fix race in mptcp_pm_nl_flush_addrs_doit() syzbot and Eulgyu Kim reported crashes in mptcp_pm_nl_get_local_id() and/or mptcp_pm_nl_is_backup() Root cause is list_splice_init() in mptcp_pm_nl_flush_addrs_doit() which is not RCU ready. list_splice_init_rcu() can not be called here while holding pernet->lock spinlock. Many thanks to Eulgyu Kim for providing a repro and testing our patches.

In the Linux kernel, the following vulnerability has been resolved: dst: fix races in rt6_uncached_list_del() and rt_del_uncached_list() syzbot was able to crash the kernel in rt6_uncached_list_flush_dev() in an interesting way [1] Crash happens in list_del_init()/INIT_LIST_HEAD() while writing list->prev, while the prior write on list->next went well. static inline void INIT_LIST_HEAD(struct list_head *list) { WRITE_ONCE(list->next, list); // This went well WRITE_ONCE(list->prev, list); // Crash, @list has been freed. } Issue here is that rt6_uncached_list_del() did not attempt to lock ul->lock, as list_empty(&rt->dst.rt_uncached) returned true because the WRITE_ONCE(list->next, list) happened on the other CPU. We might use list_del_init_careful() and list_empty_careful(), or make sure rt6_uncached_list_del() always grabs the spinlock whenever rt->dst.rt_uncached_list has been set. A similar fix is neeed for IPv4. [1] BUG: KASAN: slab-use-after-free in INIT_LIST_HEAD include/linux/list.h:46 [inline] BUG: KASAN: slab-use-after-free in list_del_init include/linux/list.h:296 [inline] BUG: KASAN: slab-use-after-free in rt6_uncached_list_flush_dev net/ipv6/route.c:191 [inline] BUG: KASAN: slab-use-after-free in rt6_disable_ip+0x633/0x730 net/ipv6/route.c:5020 Write of size 8 at addr ffff8880294cfa78 by task kworker/u8:14/3450 CPU: 0 UID: 0 PID: 3450 Comm: kworker/u8:14 Tainted: G L syzkaller #0 PREEMPT_{RT,(full)} Tainted: [L]=SOFTLOCKUP Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/25/2025 Workqueue: netns cleanup_net Call Trace: <TASK> dump_stack_lvl+0xe8/0x150 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0xca/0x240 mm/kasan/report.c:482 kasan_report+0x118/0x150 mm/kasan/report.c:595 INIT_LIST_HEAD include/linux/list.h:46 [inline] list_del_init include/linux/list.h:296 [inline] rt6_uncached_list_flush_dev net/ipv6/route.c:191 [inline] rt6_disable_ip+0x633/0x730 net/ipv6/route.c:5020 addrconf_ifdown+0x143/0x18a0 net/ipv6/addrconf.c:3853 addrconf_notify+0x1bc/0x1050 net/ipv6/addrconf.c:-1 notifier_call_chain+0x19d/0x3a0 kernel/notifier.c:85 call_netdevice_notifiers_extack net/core/dev.c:2268 [inline] call_netdevice_notifiers net/core/dev.c:2282 [inline] netif_close_many+0x29c/0x410 net/core/dev.c:1785 unregister_netdevice_many_notify+0xb50/0x2330 net/core/dev.c:12353 ops_exit_rtnl_list net/core/net_namespace.c:187 [inline] ops_undo_list+0x3dc/0x990 net/core/net_namespace.c:248 cleanup_net+0x4de/0x7b0 net/core/net_namespace.c:696 process_one_work kernel/workqueue.c:3257 [inline] process_scheduled_works+0xad1/0x1770 kernel/workqueue.c:3340 worker_thread+0x8a0/0xda0 kernel/workqueue.c:3421 kthread+0x711/0x8a0 kernel/kthread.c:463 ret_from_fork+0x510/0xa50 arch/x86/kernel/process.c:158 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:246 </TASK> Allocated by task 803: kasan_save_stack mm/kasan/common.c:57 [inline] kasan_save_track+0x3e/0x80 mm/kasan/common.c:78 unpoison_slab_object mm/kasan/common.c:340 [inline] __kasan_slab_alloc+0x6c/0x80 mm/kasan/common.c:366 kasan_slab_alloc include/linux/kasan.h:253 [inline] slab_post_alloc_hook mm/slub.c:4953 [inline] slab_alloc_node mm/slub.c:5263 [inline] kmem_cache_alloc_noprof+0x18d/0x6c0 mm/slub.c:5270 dst_alloc+0x105/0x170 net/core/dst.c:89 ip6_dst_alloc net/ipv6/route.c:342 [inline] icmp6_dst_alloc+0x75/0x460 net/ipv6/route.c:3333 mld_sendpack+0x683/0xe60 net/ipv6/mcast.c:1844 mld_send_cr net/ipv6/mcast.c:2154 [inline] mld_ifc_work+0x83e/0xd60 net/ipv6/mcast.c:2693 process_one_work kernel/workqueue.c:3257 [inline] process_scheduled_works+0xad1/0x1770 kernel/workqueue.c:3340 worker_thread+0x8a0/0xda0 kernel/workqueue.c:3421 kthread+0x711/0x8a0 kernel/kthread.c:463 ret_from_fork+0x510/0xa50 arch/x86/kernel/process.c:158 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entr ---truncated---

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Prevent concurrent access to IPSec ASO context The query or updating IPSec offload object is through Access ASO WQE. The driver uses a single mlx5e_ipsec_aso struct for each PF, which contains a shared DMA-mapped context for all ASO operations. A race condition exists because the ASO spinlock is released before the hardware has finished processing WQE. If a second operation is initiated immediately after, it overwrites the shared context in the DMA area. When the first operation's completion is processed later, it reads this corrupted context, leading to unexpected behavior and incorrect results. This commit fixes the race by introducing a private context within each IPSec offload object. The shared ASO context is now copied to this private context while the ASO spinlock is held. Subsequent processing uses this saved, per-object context, ensuring its integrity is maintained.

In the Linux kernel, the following vulnerability has been resolved: rxrpc: Fix data-race warning and potential load/store tearing Fix the following: BUG: KCSAN: data-race in rxrpc_peer_keepalive_worker / rxrpc_send_data_packet which is reporting an issue with the reads and writes to ->last_tx_at in: conn->peer->last_tx_at = ktime_get_seconds(); and: keepalive_at = peer->last_tx_at + RXRPC_KEEPALIVE_TIME; The lockless accesses to these to values aren't actually a problem as the read only needs an approximate time of last transmission for the purposes of deciding whether or not the transmission of a keepalive packet is warranted yet. Also, as ->last_tx_at is a 64-bit value, tearing can occur on a 32-bit arch. Fix both of these by switching to an unsigned int for ->last_tx_at and only storing the LSW of the time64_t. It can then be reconstructed at need provided no more than 68 years has elapsed since the last transmission.

In the Linux kernel, the following vulnerability has been resolved: gpiolib: fix race condition for gdev->srcu If two drivers were calling gpiochip_add_data_with_key(), one may be traversing the srcu-protected list in gpio_name_to_desc(), meanwhile other has just added its gdev in gpiodev_add_to_list_unlocked(). This creates a non-mutexed and non-protected timeframe, when one instance is dereferencing and using &gdev->srcu, before the other has initialized it, resulting in crash: [ 4.935481] Unable to handle kernel paging request at virtual address ffff800272bcc000 [ 4.943396] Mem abort info: [ 4.943400] ESR = 0x0000000096000005 [ 4.943403] EC = 0x25: DABT (current EL), IL = 32 bits [ 4.943407] SET = 0, FnV = 0 [ 4.943410] EA = 0, S1PTW = 0 [ 4.943413] FSC = 0x05: level 1 translation fault [ 4.943416] Data abort info: [ 4.943418] ISV = 0, ISS = 0x00000005, ISS2 = 0x00000000 [ 4.946220] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 4.955261] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 4.955268] swapper pgtable: 4k pages, 48-bit VAs, pgdp=0000000038e6c000 [ 4.961449] [ffff800272bcc000] pgd=0000000000000000 [ 4.969203] , p4d=1000000039739003 [ 4.979730] , pud=0000000000000000 [ 4.980210] phandle (CPU): 0x0000005e, phandle (BE): 0x5e000000 for node "reset" [ 4.991736] Internal error: Oops: 0000000096000005 [#1] PREEMPT SMP ... [ 5.121359] pc : __srcu_read_lock+0x44/0x98 [ 5.131091] lr : gpio_name_to_desc+0x60/0x1a0 [ 5.153671] sp : ffff8000833bb430 [ 5.298440] [ 5.298443] Call trace: [ 5.298445] __srcu_read_lock+0x44/0x98 [ 5.309484] gpio_name_to_desc+0x60/0x1a0 [ 5.320692] gpiochip_add_data_with_key+0x488/0xf00 5.946419] ---[ end trace 0000000000000000 ]--- Move initialization code for gdev fields before it is added to gpio_devices, with adjacent initialization code. Adjust goto statements to reflect modified order of operations [Bartosz: fixed a build issue, removed stray newline]

In the Linux kernel, the following vulnerability has been resolved: regmap: Fix race condition in hwspinlock irqsave routine Previously, the address of the shared member '&map->spinlock_flags' was passed directly to 'hwspin_lock_timeout_irqsave'. This creates a race condition where multiple contexts contending for the lock could overwrite the shared flags variable, potentially corrupting the state for the current lock owner. Fix this by using a local stack variable 'flags' to store the IRQ state temporarily.

In the Linux kernel, the following vulnerability has been resolved: scsi: core: Wake up the error handler when final completions race against each other The fragile ordering between marking commands completed or failed so that the error handler only wakes when the last running command completes or times out has race conditions. These race conditions can cause the SCSI layer to fail to wake the error handler, leaving I/O through the SCSI host stuck as the error state cannot advance. First, there is an memory ordering issue within scsi_dec_host_busy(). The write which clears SCMD_STATE_INFLIGHT may be reordered with reads counting in scsi_host_busy(). While the local CPU will see its own write, reordering can allow other CPUs in scsi_dec_host_busy() or scsi_eh_inc_host_failed() to see a raised busy count, causing no CPU to see a host busy equal to the host_failed count. This race condition can be prevented with a memory barrier on the error path to force the write to be visible before counting host busy commands. Second, there is a general ordering issue with scsi_eh_inc_host_failed(). By counting busy commands before incrementing host_failed, it can race with a final command in scsi_dec_host_busy(), such that scsi_dec_host_busy() does not see host_failed incremented but scsi_eh_inc_host_failed() counts busy commands before SCMD_STATE_INFLIGHT is cleared by scsi_dec_host_busy(), resulting in neither waking the error handler task. This needs the call to scsi_host_busy() to be moved after host_failed is incremented to close the race condition.

In the Linux kernel, the following vulnerability has been resolved: mm/shmem, swap: fix race of truncate and swap entry split The helper for shmem swap freeing is not handling the order of swap entries correctly. It uses xa_cmpxchg_irq to erase the swap entry, but it gets the entry order before that using xa_get_order without lock protection, and it may get an outdated order value if the entry is split or changed in other ways after the xa_get_order and before the xa_cmpxchg_irq. And besides, the order could grow and be larger than expected, and cause truncation to erase data beyond the end border. For example, if the target entry and following entries are swapped in or freed, then a large folio was added in place and swapped out, using the same entry, the xa_cmpxchg_irq will still succeed, it's very unlikely to happen though. To fix that, open code the Xarray cmpxchg and put the order retrieval and value checking in the same critical section. Also, ensure the order won't exceed the end border, skip it if the entry goes across the border. Skipping large swap entries crosses the end border is safe here. Shmem truncate iterates the range twice, in the first iteration, find_lock_entries already filtered such entries, and shmem will swapin the entries that cross the end border and partially truncate the folio (split the folio or at least zero part of it). So in the second loop here, if we see a swap entry that crosses the end order, it must at least have its content erased already. I observed random swapoff hangs and kernel panics when stress testing ZSWAP with shmem. After applying this patch, all problems are gone.

In the Linux kernel, the following vulnerability has been resolved: serial: Fix not set tty->port race condition Revert commit bfc467db60b7 ("serial: remove redundant tty_port_link_device()") because the tty_port_link_device() is not redundant: the tty->port has to be confured before we call uart_configure_port(), otherwise user-space can open console without TTY linked to the driver. This tty_port_link_device() was added explicitly to avoid this exact issue in commit fb2b90014d78 ("tty: link tty and port before configuring it as console"), so offending commit basically reverted the fix saying it is redundant without addressing the actual race condition presented there. Reproducible always as tty->port warning on Qualcomm SoC with most of devices disabled, so with very fast boot, and one serial device being the console: printk: legacy console [ttyMSM0] enabled printk: legacy console [ttyMSM0] enabled printk: legacy bootconsole [qcom_geni0] disabled printk: legacy bootconsole [qcom_geni0] disabled ------------[ cut here ]------------ tty_init_dev: ttyMSM driver does not set tty->port. This would crash the kernel. Fix the driver! WARNING: drivers/tty/tty_io.c:1414 at tty_init_dev.part.0+0x228/0x25c, CPU#2: systemd/1 Modules linked in: socinfo tcsrcc_eliza gcc_eliza sm3_ce fuse ipv6 CPU: 2 UID: 0 PID: 1 Comm: systemd Tainted: G S 6.19.0-rc4-next-20260108-00024-g2202f4d30aa8 #73 PREEMPT Tainted: [S]=CPU_OUT_OF_SPEC Hardware name: Qualcomm Technologies, Inc. Eliza (DT) ... tty_init_dev.part.0 (drivers/tty/tty_io.c:1414 (discriminator 11)) (P) tty_open (arch/arm64/include/asm/atomic_ll_sc.h:95 (discriminator 3) drivers/tty/tty_io.c:2073 (discriminator 3) drivers/tty/tty_io.c:2120 (discriminator 3)) chrdev_open (fs/char_dev.c:411) do_dentry_open (fs/open.c:962) vfs_open (fs/open.c:1094) do_open (fs/namei.c:4634) path_openat (fs/namei.c:4793) do_filp_open (fs/namei.c:4820) do_sys_openat2 (fs/open.c:1391 (discriminator 3)) ... Starting Network Name Resolution... Apparently the flow with this small Yocto-based ramdisk user-space is: driver (qcom_geni_serial.c): user-space: ============================ =========== qcom_geni_serial_probe() uart_add_one_port() serial_core_register_port() serial_core_add_one_port() uart_configure_port() register_console() | | open console | ... | tty_init_dev() | driver->ports[idx] is NULL | tty_port_register_device_attr_serdev() tty_port_link_device() <- set driver->ports[idx]

In the Linux kernel, the following vulnerability has been resolved: af_unix: Fix data-races around user->unix_inflight. user->unix_inflight is changed under spin_lock(unix_gc_lock), but too_many_unix_fds() reads it locklessly. Let's annotate the write/read accesses to user->unix_inflight. BUG: KCSAN: data-race in unix_attach_fds / unix_inflight write to 0xffffffff8546f2d0 of 8 bytes by task 44798 on cpu 1: unix_inflight+0x157/0x180 net/unix/scm.c:66 unix_attach_fds+0x147/0x1e0 net/unix/scm.c:123 unix_scm_to_skb net/unix/af_unix.c:1827 [inline] unix_dgram_sendmsg+0x46a/0x14f0 net/unix/af_unix.c:1950 unix_seqpacket_sendmsg net/unix/af_unix.c:2308 [inline] unix_seqpacket_sendmsg+0xba/0x130 net/unix/af_unix.c:2292 sock_sendmsg_nosec net/socket.c:725 [inline] sock_sendmsg+0x148/0x160 net/socket.c:748 ____sys_sendmsg+0x4e4/0x610 net/socket.c:2494 ___sys_sendmsg+0xc6/0x140 net/socket.c:2548 __sys_sendmsg+0x94/0x140 net/socket.c:2577 __do_sys_sendmsg net/socket.c:2586 [inline] __se_sys_sendmsg net/socket.c:2584 [inline] __x64_sys_sendmsg+0x45/0x50 net/socket.c:2584 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x6e/0xd8 read to 0xffffffff8546f2d0 of 8 bytes by task 44814 on cpu 0: too_many_unix_fds net/unix/scm.c:101 [inline] unix_attach_fds+0x54/0x1e0 net/unix/scm.c:110 unix_scm_to_skb net/unix/af_unix.c:1827 [inline] unix_dgram_sendmsg+0x46a/0x14f0 net/unix/af_unix.c:1950 unix_seqpacket_sendmsg net/unix/af_unix.c:2308 [inline] unix_seqpacket_sendmsg+0xba/0x130 net/unix/af_unix.c:2292 sock_sendmsg_nosec net/socket.c:725 [inline] sock_sendmsg+0x148/0x160 net/socket.c:748 ____sys_sendmsg+0x4e4/0x610 net/socket.c:2494 ___sys_sendmsg+0xc6/0x140 net/socket.c:2548 __sys_sendmsg+0x94/0x140 net/socket.c:2577 __do_sys_sendmsg net/socket.c:2586 [inline] __se_sys_sendmsg net/socket.c:2584 [inline] __x64_sys_sendmsg+0x45/0x50 net/socket.c:2584 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x6e/0xd8 value changed: 0x000000000000000c -> 0x000000000000000d Reported by Kernel Concurrency Sanitizer on: CPU: 0 PID: 44814 Comm: systemd-coredum Not tainted 6.4.0-11989-g6843306689af #6 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014

In the Linux kernel, the following vulnerability has been resolved: rxrpc: Fix potential data race in rxrpc_wait_to_be_connected() Inside the loop in rxrpc_wait_to_be_connected() it checks call->error to see if it should exit the loop without first checking the call state. This is probably safe as if call->error is set, the call is dead anyway, but we should probably wait for the call state to have been set to completion first, lest it cause surprise on the way out. Fix this by only accessing call->error if the call is complete. We don't actually need to access the error inside the loop as we'll do that after. This caused the following report: BUG: KCSAN: data-race in rxrpc_send_data / rxrpc_set_call_completion write to 0xffff888159cf3c50 of 4 bytes by task 25673 on cpu 1: rxrpc_set_call_completion+0x71/0x1c0 net/rxrpc/call_state.c:22 rxrpc_send_data_packet+0xba9/0x1650 net/rxrpc/output.c:479 rxrpc_transmit_one+0x1e/0x130 net/rxrpc/output.c:714 rxrpc_decant_prepared_tx net/rxrpc/call_event.c:326 [inline] rxrpc_transmit_some_data+0x496/0x600 net/rxrpc/call_event.c:350 rxrpc_input_call_event+0x564/0x1220 net/rxrpc/call_event.c:464 rxrpc_io_thread+0x307/0x1d80 net/rxrpc/io_thread.c:461 kthread+0x1ac/0x1e0 kernel/kthread.c:376 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:308 read to 0xffff888159cf3c50 of 4 bytes by task 25672 on cpu 0: rxrpc_send_data+0x29e/0x1950 net/rxrpc/sendmsg.c:296 rxrpc_do_sendmsg+0xb7a/0xc20 net/rxrpc/sendmsg.c:726 rxrpc_sendmsg+0x413/0x520 net/rxrpc/af_rxrpc.c:565 sock_sendmsg_nosec net/socket.c:724 [inline] sock_sendmsg net/socket.c:747 [inline] ____sys_sendmsg+0x375/0x4c0 net/socket.c:2501 ___sys_sendmsg net/socket.c:2555 [inline] __sys_sendmmsg+0x263/0x500 net/socket.c:2641 __do_sys_sendmmsg net/socket.c:2670 [inline] __se_sys_sendmmsg net/socket.c:2667 [inline] __x64_sys_sendmmsg+0x57/0x60 net/socket.c:2667 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd value changed: 0x00000000 -> 0xffffffea

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: Fix hci_suspend_sync crash If hci_unregister_dev() frees the hci_dev object but hci_suspend_notifier may still be accessing it, it can cause the program to crash. Here's the call trace: <4>[102152.653246] Call Trace: <4>[102152.653254] hci_suspend_sync+0x109/0x301 [bluetooth] <4>[102152.653259] hci_suspend_dev+0x78/0xcd [bluetooth] <4>[102152.653263] hci_suspend_notifier+0x42/0x7a [bluetooth] <4>[102152.653268] notifier_call_chain+0x43/0x6b <4>[102152.653271] __blocking_notifier_call_chain+0x48/0x69 <4>[102152.653273] __pm_notifier_call_chain+0x22/0x39 <4>[102152.653276] pm_suspend+0x287/0x57c <4>[102152.653278] state_store+0xae/0xe5 <4>[102152.653281] kernfs_fop_write+0x109/0x173 <4>[102152.653284] __vfs_write+0x16f/0x1a2 <4>[102152.653287] ? selinux_file_permission+0xca/0x16f <4>[102152.653289] ? security_file_permission+0x36/0x109 <4>[102152.653291] vfs_write+0x114/0x21d <4>[102152.653293] __x64_sys_write+0x7b/0xdb <4>[102152.653296] do_syscall_64+0x59/0x194 <4>[102152.653299] entry_SYSCALL_64_after_hwframe+0x5c/0xc1 This patch holds the reference count of the hci_dev object while processing it in hci_suspend_notifier to avoid potential crash caused by the race condition.

In the Linux kernel, the following vulnerability has been resolved: firewire: core: fix race condition against transaction list The list of transaction is enumerated without acquiring card lock when processing AR response event. This causes a race condition bug when processing AT request completion event concurrently. This commit fixes the bug by put timer start for split transaction expiration into the scope of lock. The value of jiffies in card structure is referred before acquiring the lock.

In the Linux kernel, the following vulnerability has been resolved: power: supply: bq25890: Fix external_power_changed race bq25890_charger_external_power_changed() dereferences bq->charger, which gets sets in bq25890_power_supply_init() like this: bq->charger = devm_power_supply_register(bq->dev, &bq->desc, &psy_cfg); As soon as devm_power_supply_register() has called device_add() the external_power_changed callback can get called. So there is a window where bq25890_charger_external_power_changed() may get called while bq->charger has not been set yet leading to a NULL pointer dereference. This race hits during boot sometimes on a Lenovo Yoga Book 1 yb1-x90f when the cht_wcove_pwrsrc (extcon) power_supply is done with detecting the connected charger-type which happens to exactly hit the small window: BUG: kernel NULL pointer dereference, address: 0000000000000018 <snip> RIP: 0010:__power_supply_is_supplied_by+0xb/0xb0 <snip> Call Trace: <TASK> __power_supply_get_supplier_property+0x19/0x50 class_for_each_device+0xb1/0xe0 power_supply_get_property_from_supplier+0x2e/0x50 bq25890_charger_external_power_changed+0x38/0x1b0 [bq25890_charger] __power_supply_changed_work+0x30/0x40 class_for_each_device+0xb1/0xe0 power_supply_changed_work+0x5f/0xe0 <snip> Fixing this is easy. The external_power_changed callback gets passed the power_supply which will eventually get stored in bq->charger, so bq25890_charger_external_power_changed() can simply directly use the passed in psy argument which is always valid.

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: f_fs: Remove WARN_ON in functionfs_bind This commit addresses an issue related to below kernel panic where panic_on_warn is enabled. It is caused by the unnecessary use of WARN_ON in functionsfs_bind, which easily leads to the following scenarios. 1.adb_write in adbd 2. UDC write via configfs ================= ===================== ->usb_ffs_open_thread() ->UDC write ->open_functionfs() ->configfs_write_iter() ->adb_open() ->gadget_dev_desc_UDC_store() ->adb_write() ->usb_gadget_register_driver_owner ->driver_register() ->StartMonitor() ->bus_add_driver() ->adb_read() ->gadget_bind_driver() <times-out without BIND event> ->configfs_composite_bind() ->usb_add_function() ->open_functionfs() ->ffs_func_bind() ->adb_open() ->functionfs_bind() <ffs->state !=FFS_ACTIVE> The adb_open, adb_read, and adb_write operations are invoked from the daemon, but trying to bind the function is a process that is invoked by UDC write through configfs, which opens up the possibility of a race condition between the two paths. In this race scenario, the kernel panic occurs due to the WARN_ON from functionfs_bind when panic_on_warn is enabled. This commit fixes the kernel panic by removing the unnecessary WARN_ON. Kernel panic - not syncing: kernel: panic_on_warn set ... [ 14.542395] Call trace: [ 14.542464] ffs_func_bind+0x1c8/0x14a8 [ 14.542468] usb_add_function+0xcc/0x1f0 [ 14.542473] configfs_composite_bind+0x468/0x588 [ 14.542478] gadget_bind_driver+0x108/0x27c [ 14.542483] really_probe+0x190/0x374 [ 14.542488] __driver_probe_device+0xa0/0x12c [ 14.542492] driver_probe_device+0x3c/0x220 [ 14.542498] __driver_attach+0x11c/0x1fc [ 14.542502] bus_for_each_dev+0x104/0x160 [ 14.542506] driver_attach+0x24/0x34 [ 14.542510] bus_add_driver+0x154/0x270 [ 14.542514] driver_register+0x68/0x104 [ 14.542518] usb_gadget_register_driver_owner+0x48/0xf4 [ 14.542523] gadget_dev_desc_UDC_store+0xf8/0x144 [ 14.542526] configfs_write_iter+0xf0/0x138

In the Linux kernel, the following vulnerability has been resolved: rpmsg: core: fix race in driver_override_show() and use core helper The driver_override_show function reads the driver_override string without holding the device_lock. However, the store function modifies and frees the string while holding the device_lock. This creates a race condition where the string can be freed by the store function while being read by the show function, leading to a use-after-free. To fix this, replace the rpmsg_string_attr macro with explicit show and store functions. The new driver_override_store uses the standard driver_set_override helper. Since the introduction of driver_set_override, the comments in include/linux/rpmsg.h have stated that this helper must be used to set or clear driver_override, but the implementation was not updated until now. Because driver_set_override modifies and frees the string while holding the device_lock, the new driver_override_show now correctly holds the device_lock during the read operation to prevent the race. Additionally, since rpmsg_string_attr has only ever been used for driver_override, removing the macro simplifies the code.

In the Linux kernel, the following vulnerability has been resolved: drm/xe/guc_submit: fix race around suspend_pending Currently in some testcases we can trigger: xe 0000:03:00.0: [drm] Assertion `exec_queue_destroyed(q)` failed! .... WARNING: CPU: 18 PID: 2640 at drivers/gpu/drm/xe/xe_guc_submit.c:1826 xe_guc_sched_done_handler+0xa54/0xef0 [xe] xe 0000:03:00.0: [drm] *ERROR* GT1: DEREGISTER_DONE: Unexpected engine state 0x00a1, guc_id=57 Looking at a snippet of corresponding ftrace for this GuC id we can see: 162.673311: xe_sched_msg_add: dev=0000:03:00.0, gt=1 guc_id=57, opcode=3 162.673317: xe_sched_msg_recv: dev=0000:03:00.0, gt=1 guc_id=57, opcode=3 162.673319: xe_exec_queue_scheduling_disable: dev=0000:03:00.0, 1:0x2, gt=1, width=1, guc_id=57, guc_state=0x29, flags=0x0 162.674089: xe_exec_queue_kill: dev=0000:03:00.0, 1:0x2, gt=1, width=1, guc_id=57, guc_state=0x29, flags=0x0 162.674108: xe_exec_queue_close: dev=0000:03:00.0, 1:0x2, gt=1, width=1, guc_id=57, guc_state=0xa9, flags=0x0 162.674488: xe_exec_queue_scheduling_done: dev=0000:03:00.0, 1:0x2, gt=1, width=1, guc_id=57, guc_state=0xa9, flags=0x0 162.678452: xe_exec_queue_deregister: dev=0000:03:00.0, 1:0x2, gt=1, width=1, guc_id=57, guc_state=0xa1, flags=0x0 It looks like we try to suspend the queue (opcode=3), setting suspend_pending and triggering a disable_scheduling. The user then closes the queue. However the close will also forcefully signal the suspend fence after killing the queue, later when the G2H response for disable_scheduling comes back we have now cleared suspend_pending when signalling the suspend fence, so the disable_scheduling now incorrectly tries to also deregister the queue. This leads to warnings since the queue has yet to even be marked for destruction. We also seem to trigger errors later with trying to double unregister the same queue. To fix this tweak the ordering when handling the response to ensure we don't race with a disable_scheduling that didn't actually intend to perform an unregister. The destruction path should now also correctly wait for any pending_disable before marking as destroyed. (cherry picked from commit f161809b362f027b6d72bd998e47f8f0bad60a2e)

In the Linux kernel, the following vulnerability has been resolved: accel/ivpu: Prevent recovery invocation during probe and resume Refactor IPC send and receive functions to allow correct handling of operations that should not trigger a recovery process. Expose ivpu_send_receive_internal(), which is now utilized by the D0i3 entry, DCT initialization, and HWS initialization functions. These functions have been modified to return error codes gracefully, rather than initiating recovery. The updated functions are invoked within ivpu_probe() and ivpu_resume(), ensuring that any errors encountered during these stages result in a proper teardown or shutdown sequence. The previous approach of triggering recovery within these functions could lead to a race condition, potentially causing undefined behavior and kernel crashes due to null pointer dereferences.

In the Linux kernel, the following vulnerability has been resolved: media: i2c: tc358743: Fix crash in the probe error path when using polling If an error occurs in the probe() function, we should remove the polling timer that was alarmed earlier, otherwise the timer is called with arguments that are already freed, which results in a crash. ------------[ cut here ]------------ WARNING: CPU: 3 PID: 0 at kernel/time/timer.c:1830 __run_timers+0x244/0x268 Modules linked in: CPU: 3 UID: 0 PID: 0 Comm: swapper/3 Not tainted 6.11.0 #226 Hardware name: Diasom DS-RK3568-SOM-EVB (DT) pstate: 804000c9 (Nzcv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : __run_timers+0x244/0x268 lr : __run_timers+0x1d4/0x268 sp : ffffff80eff2baf0 x29: ffffff80eff2bb50 x28: 7fffffffffffffff x27: ffffff80eff2bb00 x26: ffffffc080f669c0 x25: ffffff80efef6bf0 x24: ffffff80eff2bb00 x23: 0000000000000000 x22: dead000000000122 x21: 0000000000000000 x20: ffffff80efef6b80 x19: ffffff80041c8bf8 x18: ffffffffffffffff x17: ffffffc06f146000 x16: ffffff80eff27dc0 x15: 000000000000003e x14: 0000000000000000 x13: 00000000000054da x12: 0000000000000000 x11: 00000000000639c0 x10: 000000000000000c x9 : 0000000000000009 x8 : ffffff80eff2cb40 x7 : ffffff80eff2cb40 x6 : ffffff8002bee480 x5 : ffffffc080cb2220 x4 : ffffffc080cb2150 x3 : 00000000000f4240 x2 : 0000000000000102 x1 : ffffff80eff2bb00 x0 : ffffff80041c8bf0 Call trace:  __run_timers+0x244/0x268  timer_expire_remote+0x50/0x68  tmigr_handle_remote+0x388/0x39c  run_timer_softirq+0x38/0x44  handle_softirqs+0x138/0x298  __do_softirq+0x14/0x20  ____do_softirq+0x10/0x1c  call_on_irq_stack+0x24/0x4c  do_softirq_own_stack+0x1c/0x2c  irq_exit_rcu+0x9c/0xcc  el1_interrupt+0x48/0xc0  el1h_64_irq_handler+0x18/0x24  el1h_64_irq+0x7c/0x80  default_idle_call+0x34/0x68  do_idle+0x23c/0x294  cpu_startup_entry+0x38/0x3c  secondary_start_kernel+0x128/0x160  __secondary_switched+0xb8/0xbc ---[ end trace 0000000000000000 ]---

v9fs_wstat in hw/9pfs/9p.c in QEMU allows guest OS users to cause a denial of service (crash) because of a race condition during file renaming.

In the Linux kernel, the following vulnerability has been resolved: tty: serial: fsl_lpuart: fix race on RX DMA shutdown From time to time DMA completion can come in the middle of DMA shutdown: <process ctx>: <IRQ>: lpuart32_shutdown() lpuart_dma_shutdown() del_timer_sync() lpuart_dma_rx_complete() lpuart_copy_rx_to_tty() mod_timer() lpuart_dma_rx_free() When the timer fires a bit later, sport->dma_rx_desc is NULL: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004 pc : lpuart_copy_rx_to_tty+0xcc/0x5bc lr : lpuart_timer_func+0x1c/0x2c Call trace: lpuart_copy_rx_to_tty lpuart_timer_func call_timer_fn __run_timers.part.0 run_timer_softirq __do_softirq __irq_exit_rcu irq_exit handle_domain_irq gic_handle_irq call_on_irq_stack do_interrupt_handler ... To fix this fold del_timer_sync() into lpuart_dma_rx_free() after dmaengine_terminate_sync() to make sure timer will not be re-started in lpuart_copy_rx_to_tty() <= lpuart_dma_rx_complete().

In the Linux kernel, the following vulnerability has been resolved: nvme: tcp: avoid race between queue_lock lock and destroy Commit 76d54bf20cdc ("nvme-tcp: don't access released socket during error recovery") added a mutex_lock() call for the queue->queue_lock in nvme_tcp_get_address(). However, the mutex_lock() races with mutex_destroy() in nvme_tcp_free_queue(), and causes the WARN below. DEBUG_LOCKS_WARN_ON(lock->magic != lock) WARNING: CPU: 3 PID: 34077 at kernel/locking/mutex.c:587 __mutex_lock+0xcf0/0x1220 Modules linked in: nvmet_tcp nvmet nvme_tcp nvme_fabrics iw_cm ib_cm ib_core pktcdvd nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip_set nf_tables qrtr sunrpc ppdev 9pnet_virtio 9pnet pcspkr netfs parport_pc parport e1000 i2c_piix4 i2c_smbus loop fuse nfnetlink zram bochs drm_vram_helper drm_ttm_helper ttm drm_kms_helper xfs drm sym53c8xx floppy nvme scsi_transport_spi nvme_core nvme_auth serio_raw ata_generic pata_acpi dm_multipath qemu_fw_cfg [last unloaded: ib_uverbs] CPU: 3 UID: 0 PID: 34077 Comm: udisksd Not tainted 6.11.0-rc7 #319 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014 RIP: 0010:__mutex_lock+0xcf0/0x1220 Code: 08 84 d2 0f 85 c8 04 00 00 8b 15 ef b6 c8 01 85 d2 0f 85 78 f4 ff ff 48 c7 c6 20 93 ee af 48 c7 c7 60 91 ee af e8 f0 a7 6d fd <0f> 0b e9 5e f4 ff ff 48 b8 00 00 00 00 00 fc ff df 4c 89 f2 48 c1 RSP: 0018:ffff88811305f760 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff88812c652058 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000001 RBP: ffff88811305f8b0 R08: 0000000000000001 R09: ffffed1075c36341 R10: ffff8883ae1b1a0b R11: 0000000000010498 R12: 0000000000000000 R13: 0000000000000000 R14: dffffc0000000000 R15: ffff88812c652058 FS: 00007f9713ae4980(0000) GS:ffff8883ae180000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fcd78483c7c CR3: 0000000122c38000 CR4: 00000000000006f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? __warn.cold+0x5b/0x1af ? __mutex_lock+0xcf0/0x1220 ? report_bug+0x1ec/0x390 ? handle_bug+0x3c/0x80 ? exc_invalid_op+0x13/0x40 ? asm_exc_invalid_op+0x16/0x20 ? __mutex_lock+0xcf0/0x1220 ? nvme_tcp_get_address+0xc2/0x1e0 [nvme_tcp] ? __pfx___mutex_lock+0x10/0x10 ? __lock_acquire+0xd6a/0x59e0 ? nvme_tcp_get_address+0xc2/0x1e0 [nvme_tcp] nvme_tcp_get_address+0xc2/0x1e0 [nvme_tcp] ? __pfx_nvme_tcp_get_address+0x10/0x10 [nvme_tcp] nvme_sysfs_show_address+0x81/0xc0 [nvme_core] dev_attr_show+0x42/0x80 ? __asan_memset+0x1f/0x40 sysfs_kf_seq_show+0x1f0/0x370 seq_read_iter+0x2cb/0x1130 ? rw_verify_area+0x3b1/0x590 ? __mutex_lock+0x433/0x1220 vfs_read+0x6a6/0xa20 ? lockdep_hardirqs_on+0x78/0x100 ? __pfx_vfs_read+0x10/0x10 ksys_read+0xf7/0x1d0 ? __pfx_ksys_read+0x10/0x10 ? __x64_sys_openat+0x105/0x1d0 do_syscall_64+0x93/0x180 ? lockdep_hardirqs_on_prepare+0x16d/0x400 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on+0x78/0x100 ? do_syscall_64+0x9f/0x180 ? __pfx_ksys_read+0x10/0x10 ? lockdep_hardirqs_on_prepare+0x16d/0x400 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on+0x78/0x100 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on_prepare+0x16d/0x400 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on+0x78/0x100 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on_prepare+0x16d/0x400 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on+0x78/0x100 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on_prepare+0x16d/0x400 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on+0x78/0x100 ? do_syscall_64+0x9f/0x180 ? do_syscall_64+0x9f/0x180 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7f9713f55cfa Code: 55 48 89 e5 48 83 ec 20 48 89 55 e8 48 89 75 f0 89 7d f8 e8 e8 74 f8 ff 48 8b 55 e8 48 8b 75 f0 4 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Fix deletion race condition System crash when using debug kernel due to link list corruption. The cause of the link list corruption is due to session deletion was allowed to queue up twice. Here's the internal trace that show the same port was allowed to double queue for deletion on different cpu. 20808683956 015 qla2xxx [0000:13:00.1]-e801:4: Scheduling sess ffff93ebf9306800 for deletion 50:06:0e:80:12:48:ff:50 fc4_type 1 20808683957 027 qla2xxx [0000:13:00.1]-e801:4: Scheduling sess ffff93ebf9306800 for deletion 50:06:0e:80:12:48:ff:50 fc4_type 1 Move the clearing/setting of deleted flag lock.

In the Linux kernel, the following vulnerability has been resolved: rcu/kvfree: Fix data-race in __mod_timer / kvfree_call_rcu KCSAN reports a data race when access the krcp->monitor_work.timer.expires variable in the schedule_delayed_monitor_work() function: <snip> BUG: KCSAN: data-race in __mod_timer / kvfree_call_rcu read to 0xffff888237d1cce8 of 8 bytes by task 10149 on cpu 1: schedule_delayed_monitor_work kernel/rcu/tree.c:3520 [inline] kvfree_call_rcu+0x3b8/0x510 kernel/rcu/tree.c:3839 trie_update_elem+0x47c/0x620 kernel/bpf/lpm_trie.c:441 bpf_map_update_value+0x324/0x350 kernel/bpf/syscall.c:203 generic_map_update_batch+0x401/0x520 kernel/bpf/syscall.c:1849 bpf_map_do_batch+0x28c/0x3f0 kernel/bpf/syscall.c:5143 __sys_bpf+0x2e5/0x7a0 __do_sys_bpf kernel/bpf/syscall.c:5741 [inline] __se_sys_bpf kernel/bpf/syscall.c:5739 [inline] __x64_sys_bpf+0x43/0x50 kernel/bpf/syscall.c:5739 x64_sys_call+0x2625/0x2d60 arch/x86/include/generated/asm/syscalls_64.h:322 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xc9/0x1c0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f write to 0xffff888237d1cce8 of 8 bytes by task 56 on cpu 0: __mod_timer+0x578/0x7f0 kernel/time/timer.c:1173 add_timer_global+0x51/0x70 kernel/time/timer.c:1330 __queue_delayed_work+0x127/0x1a0 kernel/workqueue.c:2523 queue_delayed_work_on+0xdf/0x190 kernel/workqueue.c:2552 queue_delayed_work include/linux/workqueue.h:677 [inline] schedule_delayed_monitor_work kernel/rcu/tree.c:3525 [inline] kfree_rcu_monitor+0x5e8/0x660 kernel/rcu/tree.c:3643 process_one_work kernel/workqueue.c:3229 [inline] process_scheduled_works+0x483/0x9a0 kernel/workqueue.c:3310 worker_thread+0x51d/0x6f0 kernel/workqueue.c:3391 kthread+0x1d1/0x210 kernel/kthread.c:389 ret_from_fork+0x4b/0x60 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 Reported by Kernel Concurrency Sanitizer on: CPU: 0 UID: 0 PID: 56 Comm: kworker/u8:4 Not tainted 6.12.0-rc2-syzkaller-00050-g5b7c893ed5ed #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 Workqueue: events_unbound kfree_rcu_monitor <snip> kfree_rcu_monitor() rearms the work if a "krcp" has to be still offloaded and this is done without holding krcp->lock, whereas the kvfree_call_rcu() holds it. Fix it by acquiring the "krcp->lock" for kfree_rcu_monitor() so both functions do not race anymore.

In the Linux kernel, the following vulnerability has been resolved: timers: Fix NULL function pointer race in timer_shutdown_sync() There is a race condition between timer_shutdown_sync() and timer expiration that can lead to hitting a WARN_ON in expire_timers(). The issue occurs when timer_shutdown_sync() clears the timer function to NULL while the timer is still running on another CPU. The race scenario looks like this: CPU0 CPU1 <SOFTIRQ> lock_timer_base() expire_timers() base->running_timer = timer; unlock_timer_base() [call_timer_fn enter] mod_timer() ... timer_shutdown_sync() lock_timer_base() // For now, will not detach the timer but only clear its function to NULL if (base->running_timer != timer) ret = detach_if_pending(timer, base, true); if (shutdown) timer->function = NULL; unlock_timer_base() [call_timer_fn exit] lock_timer_base() base->running_timer = NULL; unlock_timer_base() ... // Now timer is pending while its function set to NULL. // next timer trigger <SOFTIRQ> expire_timers() WARN_ON_ONCE(!fn) // hit ... lock_timer_base() // Now timer will detach if (base->running_timer != timer) ret = detach_if_pending(timer, base, true); if (shutdown) timer->function = NULL; unlock_timer_base() The problem is that timer_shutdown_sync() clears the timer function regardless of whether the timer is currently running. This can leave a pending timer with a NULL function pointer, which triggers the WARN_ON_ONCE(!fn) check in expire_timers(). Fix this by only clearing the timer function when actually detaching the timer. If the timer is running, leave the function pointer intact, which is safe because the timer will be properly detached when it finishes running.

In the Linux kernel, the following vulnerability has been resolved: accel/ivpu: Fix race condition when unbinding BOs Fix 'Memory manager not clean during takedown' warning that occurs when ivpu_gem_bo_free() removes the BO from the BOs list before it gets unmapped. Then file_priv_unbind() triggers a warning in drm_mm_takedown() during context teardown. Protect the unmapping sequence with bo_list_lock to ensure the BO is always fully unmapped when removed from the list. This ensures the BO is either fully unmapped at context teardown time or present on the list and unmapped by file_priv_unbind().