In the Linux kernel, the following vulnerability has been resolved: iio: health: afe4403: Fix oob read in afe4403_read_raw KASAN report out-of-bounds read as follows: BUG: KASAN: global-out-of-bounds in afe4403_read_raw+0x42e/0x4c0 Read of size 4 at addr ffffffffc02ac638 by task cat/279 Call Trace: afe4403_read_raw iio_read_channel_info dev_attr_show The buggy address belongs to the variable: afe4403_channel_leds+0x18/0xffffffffffffe9e0 This issue can be reproduced by singe command: $ cat /sys/bus/spi/devices/spi0.0/iio\:device0/in_intensity6_raw The array size of afe4403_channel_leds is less than channels, so access with chan->address cause OOB read in afe4403_read_raw. Fix it by moving access before use it.

In the Linux kernel, the following vulnerability has been resolved: powerpc/xive/spapr: correct bitmap allocation size kasan detects access beyond the end of the xibm->bitmap allocation: BUG: KASAN: slab-out-of-bounds in _find_first_zero_bit+0x40/0x140 Read of size 8 at addr c00000001d1d0118 by task swapper/0/1 CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.19.0-rc2-00001-g90df023b36dd #28 Call Trace: [c00000001d98f770] [c0000000012baab8] dump_stack_lvl+0xac/0x108 (unreliable) [c00000001d98f7b0] [c00000000068faac] print_report+0x37c/0x710 [c00000001d98f880] [c0000000006902c0] kasan_report+0x110/0x354 [c00000001d98f950] [c000000000692324] __asan_load8+0xa4/0xe0 [c00000001d98f970] [c0000000011c6ed0] _find_first_zero_bit+0x40/0x140 [c00000001d98f9b0] [c0000000000dbfbc] xive_spapr_get_ipi+0xcc/0x260 [c00000001d98fa70] [c0000000000d6d28] xive_setup_cpu_ipi+0x1e8/0x450 [c00000001d98fb30] [c000000004032a20] pSeries_smp_probe+0x5c/0x118 [c00000001d98fb60] [c000000004018b44] smp_prepare_cpus+0x944/0x9ac [c00000001d98fc90] [c000000004009f9c] kernel_init_freeable+0x2d4/0x640 [c00000001d98fd90] [c0000000000131e8] kernel_init+0x28/0x1d0 [c00000001d98fe10] [c00000000000cd54] ret_from_kernel_thread+0x5c/0x64 Allocated by task 0: kasan_save_stack+0x34/0x70 __kasan_kmalloc+0xb4/0xf0 __kmalloc+0x268/0x540 xive_spapr_init+0x4d0/0x77c pseries_init_irq+0x40/0x27c init_IRQ+0x44/0x84 start_kernel+0x2a4/0x538 start_here_common+0x1c/0x20 The buggy address belongs to the object at c00000001d1d0118 which belongs to the cache kmalloc-8 of size 8 The buggy address is located 0 bytes inside of 8-byte region [c00000001d1d0118, c00000001d1d0120) The buggy address belongs to the physical page: page:c00c000000074740 refcount:1 mapcount:0 mapping:0000000000000000 index:0xc00000001d1d0558 pfn:0x1d1d flags: 0x7ffff000000200(slab|node=0|zone=0|lastcpupid=0x7ffff) raw: 007ffff000000200 c00000001d0003c8 c00000001d0003c8 c00000001d010480 raw: c00000001d1d0558 0000000001e1000a 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: c00000001d1d0000: fc 00 fc fc fc fc fc fc fc fc fc fc fc fc fc fc c00000001d1d0080: fc fc 00 fc fc fc fc fc fc fc fc fc fc fc fc fc >c00000001d1d0100: fc fc fc 02 fc fc fc fc fc fc fc fc fc fc fc fc ^ c00000001d1d0180: fc fc fc fc 04 fc fc fc fc fc fc fc fc fc fc fc c00000001d1d0200: fc fc fc fc fc 04 fc fc fc fc fc fc fc fc fc fc This happens because the allocation uses the wrong unit (bits) when it should pass (BITS_TO_LONGS(count) * sizeof(long)) or equivalent. With small numbers of bits, the allocated object can be smaller than sizeof(long), which results in invalid accesses. Use bitmap_zalloc() to allocate and initialize the irq bitmap, paired with bitmap_free() for consistency.

In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Fix an out-of-bounds bug in __snd_usb_parse_audio_interface() There may be a bad USB audio device with a USB ID of (0x04fa, 0x4201) and the number of it's interfaces less than 4, an out-of-bounds read bug occurs when parsing the interface descriptor for this device. Fix this by checking the number of interfaces.

In the Linux kernel, the following vulnerability has been resolved: usb: isp1760: Fix out-of-bounds array access Running the driver through kasan gives an interesting splat: BUG: KASAN: global-out-of-bounds in isp1760_register+0x180/0x70c Read of size 20 at addr f1db2e64 by task swapper/0/1 (...) isp1760_register from isp1760_plat_probe+0x1d8/0x220 (...) This happens because the loop reading the regmap fields for the different ISP1760 variants look like this: for (i = 0; i < HC_FIELD_MAX; i++) { ... } Meaning it expects the arrays to be at least HC_FIELD_MAX - 1 long. However the arrays isp1760_hc_reg_fields[], isp1763_hc_reg_fields[], isp1763_hc_volatile_ranges[] and isp1763_dc_volatile_ranges[] are dynamically sized during compilation. Fix this by putting an empty assignment to the [HC_FIELD_MAX] and [DC_FIELD_MAX] array member at the end of each array. This will make the array one member longer than it needs to be, but avoids the risk of overwriting whatever is inside [HC_FIELD_MAX - 1] and is simple and intuitive to read. Also add comments explaining what is going on.

In the Linux kernel, the following vulnerability has been resolved: net: mvneta: Prevent out of bounds read in mvneta_config_rss() The pp->indir[0] value comes from the user. It is passed to: if (cpu_online(pp->rxq_def)) inside the mvneta_percpu_elect() function. It needs bounds checkeding to ensure that it is not beyond the end of the cpu bitmap.

In the Linux kernel, the following vulnerability has been resolved: HID: hid-thrustmaster: fix OOB read in thrustmaster_interrupts Syzbot reported an slab-out-of-bounds Read in thrustmaster_probe() bug. The root case is in missing validation check of actual number of endpoints. Code should not blindly access usb_host_interface::endpoint array, since it may contain less endpoints than code expects. Fix it by adding missing validaion check and print an error if number of endpoints do not match expected number

In the Linux kernel, the following vulnerability has been resolved: drm/dp: Fix OOB read when handling Post Cursor2 register The link_status array was not large enough to read the Adjust Request Post Cursor2 register, so remove the common helper function to avoid an OOB read, found with a -Warray-bounds build: drivers/gpu/drm/drm_dp_helper.c: In function 'drm_dp_get_adjust_request_post_cursor': drivers/gpu/drm/drm_dp_helper.c:59:27: error: array subscript 10 is outside array bounds of 'const u8[6]' {aka 'const unsigned char[6]'} [-Werror=array-bounds] 59 | return link_status[r - DP_LANE0_1_STATUS]; | ~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~ drivers/gpu/drm/drm_dp_helper.c:147:51: note: while referencing 'link_status' 147 | u8 drm_dp_get_adjust_request_post_cursor(const u8 link_status[DP_LINK_STATUS_SIZE], | ~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Replace the only user of the helper with an open-coded fetch and decode, similar to drivers/gpu/drm/amd/display/dc/core/dc_link_dp.c.

In the Linux kernel, the following vulnerability has been resolved: Squashfs: check the inode number is not the invalid value of zero Syskiller has produced an out of bounds access in fill_meta_index(). That out of bounds access is ultimately caused because the inode has an inode number with the invalid value of zero, which was not checked. The reason this causes the out of bounds access is due to following sequence of events: 1. Fill_meta_index() is called to allocate (via empty_meta_index()) and fill a metadata index. It however suffers a data read error and aborts, invalidating the newly returned empty metadata index. It does this by setting the inode number of the index to zero, which means unused (zero is not a valid inode number). 2. When fill_meta_index() is subsequently called again on another read operation, locate_meta_index() returns the previous index because it matches the inode number of 0. Because this index has been returned it is expected to have been filled, and because it hasn't been, an out of bounds access is performed. This patch adds a sanity check which checks that the inode number is not zero when the inode is created and returns -EINVAL if it is. [phillip@squashfs.org.uk: whitespace fix]

In the Linux kernel, the following vulnerability has been resolved: tunnels: fix out of bounds access when building IPv6 PMTU error If the ICMPv6 error is built from a non-linear skb we get the following splat, BUG: KASAN: slab-out-of-bounds in do_csum+0x220/0x240 Read of size 4 at addr ffff88811d402c80 by task netperf/820 CPU: 0 PID: 820 Comm: netperf Not tainted 6.8.0-rc1+ #543 ... kasan_report+0xd8/0x110 do_csum+0x220/0x240 csum_partial+0xc/0x20 skb_tunnel_check_pmtu+0xeb9/0x3280 vxlan_xmit_one+0x14c2/0x4080 vxlan_xmit+0xf61/0x5c00 dev_hard_start_xmit+0xfb/0x510 __dev_queue_xmit+0x7cd/0x32a0 br_dev_queue_push_xmit+0x39d/0x6a0 Use skb_checksum instead of csum_partial who cannot deal with non-linear SKBs.

In the Linux kernel, the following vulnerability has been resolved: um: Fix out-of-bounds read in LDT setup syscall_stub_data() expects the data_count parameter to be the number of longs, not bytes. ================================================================== BUG: KASAN: stack-out-of-bounds in syscall_stub_data+0x70/0xe0 Read of size 128 at addr 000000006411f6f0 by task swapper/1 CPU: 0 PID: 1 Comm: swapper Not tainted 5.18.0+ #18 Call Trace: show_stack.cold+0x166/0x2a7 __dump_stack+0x3a/0x43 dump_stack_lvl+0x1f/0x27 print_report.cold+0xdb/0xf81 kasan_report+0x119/0x1f0 kasan_check_range+0x3a3/0x440 memcpy+0x52/0x140 syscall_stub_data+0x70/0xe0 write_ldt_entry+0xac/0x190 init_new_ldt+0x515/0x960 init_new_context+0x2c4/0x4d0 mm_init.constprop.0+0x5ed/0x760 mm_alloc+0x118/0x170 0x60033f48 do_one_initcall+0x1d7/0x860 0x60003e7b kernel_init+0x6e/0x3d4 new_thread_handler+0x1e7/0x2c0 The buggy address belongs to stack of task swapper/1 and is located at offset 64 in frame: init_new_ldt+0x0/0x960 This frame has 2 objects: [32, 40) 'addr' [64, 80) 'desc' ==================================================================

In the Linux kernel, the following vulnerability has been resolved: iio: health: afe4404: Fix oob read in afe4404_[read|write]_raw KASAN report out-of-bounds read as follows: BUG: KASAN: global-out-of-bounds in afe4404_read_raw+0x2ce/0x380 Read of size 4 at addr ffffffffc00e4658 by task cat/278 Call Trace: afe4404_read_raw iio_read_channel_info dev_attr_show The buggy address belongs to the variable: afe4404_channel_leds+0x18/0xffffffffffffe9c0 This issue can be reproduce by singe command: $ cat /sys/bus/i2c/devices/0-0058/iio\:device0/in_intensity6_raw The array size of afe4404_channel_leds and afe4404_channel_offdacs are less than channels, so access with chan->address cause OOB read in afe4404_[read|write]_raw. Fix it by moving access before use them.

In the Linux kernel, the following vulnerability has been resolved: exfat: check if cluster num is valid Syzbot reported slab-out-of-bounds read in exfat_clear_bitmap. This was triggered by reproducer calling truncute with size 0, which causes the following trace: BUG: KASAN: slab-out-of-bounds in exfat_clear_bitmap+0x147/0x490 fs/exfat/balloc.c:174 Read of size 8 at addr ffff888115aa9508 by task syz-executor251/365 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack_lvl+0x1e2/0x24b lib/dump_stack.c:118 print_address_description+0x81/0x3c0 mm/kasan/report.c:233 __kasan_report mm/kasan/report.c:419 [inline] kasan_report+0x1a4/0x1f0 mm/kasan/report.c:436 __asan_report_load8_noabort+0x14/0x20 mm/kasan/report_generic.c:309 exfat_clear_bitmap+0x147/0x490 fs/exfat/balloc.c:174 exfat_free_cluster+0x25a/0x4a0 fs/exfat/fatent.c:181 __exfat_truncate+0x99e/0xe00 fs/exfat/file.c:217 exfat_truncate+0x11b/0x4f0 fs/exfat/file.c:243 exfat_setattr+0xa03/0xd40 fs/exfat/file.c:339 notify_change+0xb76/0xe10 fs/attr.c:336 do_truncate+0x1ea/0x2d0 fs/open.c:65 Move the is_valid_cluster() helper from fatent.c to a common header to make it reusable in other *.c files. And add is_valid_cluster() to validate if cluster number is within valid range in exfat_clear_bitmap() and exfat_set_bitmap().

In the Linux kernel, the following vulnerability has been resolved: ASoC: hdmi-codec: Fix OOB memory accesses Correct size of iec_status array by changing it to the size of status array of the struct snd_aes_iec958. This fixes out-of-bounds slab read accesses made by memcpy() of the hdmi-codec driver. This problem is reported by KASAN.

An issue was discovered in the Linux kernel before 6.0.11. Missing offset validation in drivers/net/wireless/microchip/wilc1000/hif.c in the WILC1000 wireless driver can trigger an out-of-bounds read when parsing a Robust Security Network (RSN) information element from a Netlink packet.

In the Linux kernel, the following vulnerability has been resolved: net: qualcomm: rmnet: fix global oob in rmnet_policy The variable rmnet_link_ops assign a *bigger* maxtype which leads to a global out-of-bounds read when parsing the netlink attributes. See bug trace below: ================================================================== BUG: KASAN: global-out-of-bounds in validate_nla lib/nlattr.c:386 [inline] BUG: KASAN: global-out-of-bounds in __nla_validate_parse+0x24af/0x2750 lib/nlattr.c:600 Read of size 1 at addr ffffffff92c438d0 by task syz-executor.6/84207 CPU: 0 PID: 84207 Comm: syz-executor.6 Tainted: G N 6.1.0 #3 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x8b/0xb3 lib/dump_stack.c:106 print_address_description mm/kasan/report.c:284 [inline] print_report+0x172/0x475 mm/kasan/report.c:395 kasan_report+0xbb/0x1c0 mm/kasan/report.c:495 validate_nla lib/nlattr.c:386 [inline] __nla_validate_parse+0x24af/0x2750 lib/nlattr.c:600 __nla_parse+0x3e/0x50 lib/nlattr.c:697 nla_parse_nested_deprecated include/net/netlink.h:1248 [inline] __rtnl_newlink+0x50a/0x1880 net/core/rtnetlink.c:3485 rtnl_newlink+0x64/0xa0 net/core/rtnetlink.c:3594 rtnetlink_rcv_msg+0x43c/0xd70 net/core/rtnetlink.c:6091 netlink_rcv_skb+0x14f/0x410 net/netlink/af_netlink.c:2540 netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline] netlink_unicast+0x54e/0x800 net/netlink/af_netlink.c:1345 netlink_sendmsg+0x930/0xe50 net/netlink/af_netlink.c:1921 sock_sendmsg_nosec net/socket.c:714 [inline] sock_sendmsg+0x154/0x190 net/socket.c:734 ____sys_sendmsg+0x6df/0x840 net/socket.c:2482 ___sys_sendmsg+0x110/0x1b0 net/socket.c:2536 __sys_sendmsg+0xf3/0x1c0 net/socket.c:2565 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd RIP: 0033:0x7fdcf2072359 Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 f1 19 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007fdcf13e3168 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00007fdcf219ff80 RCX: 00007fdcf2072359 RDX: 0000000000000000 RSI: 0000000020000200 RDI: 0000000000000003 RBP: 00007fdcf20bd493 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 00007fffbb8d7bdf R14: 00007fdcf13e3300 R15: 0000000000022000 </TASK> The buggy address belongs to the variable: rmnet_policy+0x30/0xe0 The buggy address belongs to the physical page: page:0000000065bdeb3c refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x155243 flags: 0x200000000001000(reserved|node=0|zone=2) raw: 0200000000001000 ffffea00055490c8 ffffea00055490c8 0000000000000000 raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffffffff92c43780: f9 f9 f9 f9 00 00 00 02 f9 f9 f9 f9 00 00 00 07 ffffffff92c43800: f9 f9 f9 f9 00 00 00 05 f9 f9 f9 f9 06 f9 f9 f9 >ffffffff92c43880: f9 f9 f9 f9 00 00 00 00 00 00 f9 f9 f9 f9 f9 f9 ^ ffffffff92c43900: 00 00 00 00 00 00 00 00 07 f9 f9 f9 f9 f9 f9 f9 ffffffff92c43980: 00 00 00 07 f9 f9 f9 f9 00 00 00 05 f9 f9 f9 f9 According to the comment of `nla_parse_nested_deprecated`, the maxtype should be len(destination array) - 1. Hence use `IFLA_RMNET_MAX` here.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: validate mech token in session setup If client send invalid mech token in session setup request, ksmbd validate and make the error if it is invalid.

In the Linux kernel, the following vulnerability has been resolved: jfs: fix slab-out-of-bounds read in ea_get() During the "size_check" label in ea_get(), the code checks if the extended attribute list (xattr) size matches ea_size. If not, it logs "ea_get: invalid extended attribute" and calls print_hex_dump(). Here, EALIST_SIZE(ea_buf->xattr) returns 4110417968, which exceeds INT_MAX (2,147,483,647). Then ea_size is clamped: int size = clamp_t(int, ea_size, 0, EALIST_SIZE(ea_buf->xattr)); Although clamp_t aims to bound ea_size between 0 and 4110417968, the upper limit is treated as an int, causing an overflow above 2^31 - 1. This leads "size" to wrap around and become negative (-184549328). The "size" is then passed to print_hex_dump() (called "len" in print_hex_dump()), it is passed as type size_t (an unsigned type), this is then stored inside a variable called "int remaining", which is then assigned to "int linelen" which is then passed to hex_dump_to_buffer(). In print_hex_dump() the for loop, iterates through 0 to len-1, where len is 18446744073525002176, calling hex_dump_to_buffer() on each iteration: for (i = 0; i < len; i += rowsize) { linelen = min(remaining, rowsize); remaining -= rowsize; hex_dump_to_buffer(ptr + i, linelen, rowsize, groupsize, linebuf, sizeof(linebuf), ascii); ... } The expected stopping condition (i < len) is effectively broken since len is corrupted and very large. This eventually leads to the "ptr+i" being passed to hex_dump_to_buffer() to get closer to the end of the actual bounds of "ptr", eventually an out of bounds access is done in hex_dump_to_buffer() in the following for loop: for (j = 0; j < len; j++) { if (linebuflen < lx + 2) goto overflow2; ch = ptr[j]; ... } To fix this we should validate "EALIST_SIZE(ea_buf->xattr)" before it is utilised.

In the Linux kernel, the following vulnerability has been resolved: wifi: brcmfmac: Check the count value of channel spec to prevent out-of-bounds reads This patch fixes slab-out-of-bounds reads in brcmfmac that occur in brcmf_construct_chaninfo() and brcmf_enable_bw40_2g() when the count value of channel specifications provided by the device is greater than the length of 'list->element[]', decided by the size of the 'list' allocated with kzalloc(). The patch adds checks that make the functions free the buffer and return -EINVAL if that is the case. Note that the negative return is handled by the caller, brcmf_setup_wiphybands() or brcmf_cfg80211_attach(). Found by a modified version of syzkaller. Crash Report from brcmf_construct_chaninfo(): ================================================================== BUG: KASAN: slab-out-of-bounds in brcmf_setup_wiphybands+0x1238/0x1430 Read of size 4 at addr ffff888115f24600 by task kworker/0:2/1896 CPU: 0 PID: 1896 Comm: kworker/0:2 Tainted: G W O 5.14.0+ #132 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 Workqueue: usb_hub_wq hub_event Call Trace: dump_stack_lvl+0x57/0x7d print_address_description.constprop.0.cold+0x93/0x334 kasan_report.cold+0x83/0xdf brcmf_setup_wiphybands+0x1238/0x1430 brcmf_cfg80211_attach+0x2118/0x3fd0 brcmf_attach+0x389/0xd40 brcmf_usb_probe+0x12de/0x1690 usb_probe_interface+0x25f/0x710 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 bus_for_each_drv+0x123/0x1a0 __device_attach+0x207/0x330 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 usb_set_configuration+0x984/0x1770 usb_generic_driver_probe+0x69/0x90 usb_probe_device+0x9c/0x220 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 bus_for_each_drv+0x123/0x1a0 __device_attach+0x207/0x330 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 usb_new_device.cold+0x463/0xf66 hub_event+0x10d5/0x3330 process_one_work+0x873/0x13e0 worker_thread+0x8b/0xd10 kthread+0x379/0x450 ret_from_fork+0x1f/0x30 Allocated by task 1896: kasan_save_stack+0x1b/0x40 __kasan_kmalloc+0x7c/0x90 kmem_cache_alloc_trace+0x19e/0x330 brcmf_setup_wiphybands+0x290/0x1430 brcmf_cfg80211_attach+0x2118/0x3fd0 brcmf_attach+0x389/0xd40 brcmf_usb_probe+0x12de/0x1690 usb_probe_interface+0x25f/0x710 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 bus_for_each_drv+0x123/0x1a0 __device_attach+0x207/0x330 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 usb_set_configuration+0x984/0x1770 usb_generic_driver_probe+0x69/0x90 usb_probe_device+0x9c/0x220 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 bus_for_each_drv+0x123/0x1a0 __device_attach+0x207/0x330 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 usb_new_device.cold+0x463/0xf66 hub_event+0x10d5/0x3330 process_one_work+0x873/0x13e0 worker_thread+0x8b/0xd10 kthread+0x379/0x450 ret_from_fork+0x1f/0x30 The buggy address belongs to the object at ffff888115f24000 which belongs to the cache kmalloc-2k of size 2048 The buggy address is located 1536 bytes inside of 2048-byte region [ffff888115f24000, ffff888115f24800) Memory state around the buggy address: ffff888115f24500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff888115f24580: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffff888115f24600: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffff888115f24680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff888115f24700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ================================================================== Crash Report from brcmf_enable_bw40_2g(): ========== ---truncated---

In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: limit printed string from FW file There's no guarantee here that the file is always with a NUL-termination, so reading the string may read beyond the end of the TLV. If that's the last TLV in the file, it can perhaps even read beyond the end of the file buffer. Fix that by limiting the print format to the size of the buffer we have.

In the Linux kernel, the following vulnerability has been resolved: vlan: enforce underlying device type Currently, VLAN devices can be created on top of non-ethernet devices. Besides the fact that it doesn't make much sense, this also causes a bug which leaks the address of a kernel function to usermode. When creating a VLAN device, we initialize GARP (garp_init_applicant) and MRP (mrp_init_applicant) for the underlying device. As part of the initialization process, we add the multicast address of each applicant to the underlying device, by calling dev_mc_add. __dev_mc_add uses dev->addr_len to determine the length of the new multicast address. This causes an out-of-bounds read if dev->addr_len is greater than 6, since the multicast addresses provided by GARP and MRP are only 6 bytes long. This behaviour can be reproduced using the following commands: ip tunnel add gretest mode ip6gre local ::1 remote ::2 dev lo ip l set up dev gretest ip link add link gretest name vlantest type vlan id 100 Then, the following command will display the address of garp_pdu_rcv: ip maddr show | grep 01:80:c2:00:00:21 Fix the bug by enforcing the type of the underlying device during VLAN device initialization.

In the Linux kernel, the following vulnerability has been resolved: kvm: avoid speculation-based attacks from out-of-range memslot accesses KVM's mechanism for accessing guest memory translates a guest physical address (gpa) to a host virtual address using the right-shifted gpa (also known as gfn) and a struct kvm_memory_slot. The translation is performed in __gfn_to_hva_memslot using the following formula: hva = slot->userspace_addr + (gfn - slot->base_gfn) * PAGE_SIZE It is expected that gfn falls within the boundaries of the guest's physical memory. However, a guest can access invalid physical addresses in such a way that the gfn is invalid. __gfn_to_hva_memslot is called from kvm_vcpu_gfn_to_hva_prot, which first retrieves a memslot through __gfn_to_memslot. While __gfn_to_memslot does check that the gfn falls within the boundaries of the guest's physical memory or not, a CPU can speculate the result of the check and continue execution speculatively using an illegal gfn. The speculation can result in calculating an out-of-bounds hva. If the resulting host virtual address is used to load another guest physical address, this is effectively a Spectre gadget consisting of two consecutive reads, the second of which is data dependent on the first. Right now it's not clear if there are any cases in which this is exploitable. One interesting case was reported by the original author of this patch, and involves visiting guest page tables on x86. Right now these are not vulnerable because the hva read goes through get_user(), which contains an LFENCE speculation barrier. However, there are patches in progress for x86 uaccess.h to mask kernel addresses instead of using LFENCE; once these land, a guest could use speculation to read from the VMM's ring 3 address space. Other architectures such as ARM already use the address masking method, and would be susceptible to this same kind of data-dependent access gadgets. Therefore, this patch proactively protects from these attacks by masking out-of-bounds gfns in __gfn_to_hva_memslot, which blocks speculation of invalid hvas. Sean Christopherson noted that this patch does not cover kvm_read_guest_offset_cached. This however is limited to a few bytes past the end of the cache, and therefore it is unlikely to be useful in the context of building a chain of data dependent accesses.

In the Linux kernel, the following vulnerability has been resolved: net: validate lwtstate->data before returning from skb_tunnel_info() skb_tunnel_info() returns pointer of lwtstate->data as ip_tunnel_info type without validation. lwtstate->data can have various types such as mpls_iptunnel_encap, etc and these are not compatible. So skb_tunnel_info() should validate before returning that pointer. Splat looks like: BUG: KASAN: slab-out-of-bounds in vxlan_get_route+0x418/0x4b0 [vxlan] Read of size 2 at addr ffff888106ec2698 by task ping/811 CPU: 1 PID: 811 Comm: ping Not tainted 5.13.0+ #1195 Call Trace: dump_stack_lvl+0x56/0x7b print_address_description.constprop.8.cold.13+0x13/0x2ee ? vxlan_get_route+0x418/0x4b0 [vxlan] ? vxlan_get_route+0x418/0x4b0 [vxlan] kasan_report.cold.14+0x83/0xdf ? vxlan_get_route+0x418/0x4b0 [vxlan] vxlan_get_route+0x418/0x4b0 [vxlan] [ ... ] vxlan_xmit_one+0x148b/0x32b0 [vxlan] [ ... ] vxlan_xmit+0x25c5/0x4780 [vxlan] [ ... ] dev_hard_start_xmit+0x1ae/0x6e0 __dev_queue_xmit+0x1f39/0x31a0 [ ... ] neigh_xmit+0x2f9/0x940 mpls_xmit+0x911/0x1600 [mpls_iptunnel] lwtunnel_xmit+0x18f/0x450 ip_finish_output2+0x867/0x2040 [ ... ]

In the Linux kernel, the following vulnerability has been resolved: sch_cake: Fix out of bounds when parsing TCP options and header The TCP option parser in cake qdisc (cake_get_tcpopt and cake_tcph_may_drop) could read one byte out of bounds. When the length is 1, the execution flow gets into the loop, reads one byte of the opcode, and if the opcode is neither TCPOPT_EOL nor TCPOPT_NOP, it reads one more byte, which exceeds the length of 1. This fix is inspired by commit 9609dad263f8 ("ipv4: tcp_input: fix stack out of bounds when parsing TCP options."). v2 changes: Added doff validation in cake_get_tcphdr to avoid parsing garbage as TCP header. Although it wasn't strictly an out-of-bounds access (memory was allocated), garbage values could be read where CAKE expected the TCP header if doff was smaller than 5.

In the Linux kernel, the following vulnerability has been resolved: net/sched: fq_pie: fix OOB access in the traffic path the following script: # tc qdisc add dev eth0 handle 0x1 root fq_pie flows 2 # tc qdisc add dev eth0 clsact # tc filter add dev eth0 egress matchall action skbedit priority 0x10002 # ping 192.0.2.2 -I eth0 -c2 -w1 -q produces the following splat: BUG: KASAN: slab-out-of-bounds in fq_pie_qdisc_enqueue+0x1314/0x19d0 [sch_fq_pie] Read of size 4 at addr ffff888171306924 by task ping/942 CPU: 3 PID: 942 Comm: ping Not tainted 5.12.0+ #441 Hardware name: Red Hat KVM, BIOS 1.11.1-4.module+el8.1.0+4066+0f1aadab 04/01/2014 Call Trace: dump_stack+0x92/0xc1 print_address_description.constprop.7+0x1a/0x150 kasan_report.cold.13+0x7f/0x111 fq_pie_qdisc_enqueue+0x1314/0x19d0 [sch_fq_pie] __dev_queue_xmit+0x1034/0x2b10 ip_finish_output2+0xc62/0x2120 __ip_finish_output+0x553/0xea0 ip_output+0x1ca/0x4d0 ip_send_skb+0x37/0xa0 raw_sendmsg+0x1c4b/0x2d00 sock_sendmsg+0xdb/0x110 __sys_sendto+0x1d7/0x2b0 __x64_sys_sendto+0xdd/0x1b0 do_syscall_64+0x3c/0x80 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7fe69735c3eb Code: 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 f3 0f 1e fa 48 8d 05 75 42 2c 00 41 89 ca 8b 00 85 c0 75 14 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 75 c3 0f 1f 40 00 41 57 4d 89 c7 41 56 41 89 RSP: 002b:00007fff06d7fb38 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 000055e961413700 RCX: 00007fe69735c3eb RDX: 0000000000000040 RSI: 000055e961413700 RDI: 0000000000000003 RBP: 0000000000000040 R08: 000055e961410500 R09: 0000000000000010 R10: 0000000000000000 R11: 0000000000000246 R12: 00007fff06d81260 R13: 00007fff06d7fb40 R14: 00007fff06d7fc30 R15: 000055e96140f0a0 Allocated by task 917: kasan_save_stack+0x19/0x40 __kasan_kmalloc+0x7f/0xa0 __kmalloc_node+0x139/0x280 fq_pie_init+0x555/0x8e8 [sch_fq_pie] qdisc_create+0x407/0x11b0 tc_modify_qdisc+0x3c2/0x17e0 rtnetlink_rcv_msg+0x346/0x8e0 netlink_rcv_skb+0x120/0x380 netlink_unicast+0x439/0x630 netlink_sendmsg+0x719/0xbf0 sock_sendmsg+0xe2/0x110 ____sys_sendmsg+0x5ba/0x890 ___sys_sendmsg+0xe9/0x160 __sys_sendmsg+0xd3/0x170 do_syscall_64+0x3c/0x80 entry_SYSCALL_64_after_hwframe+0x44/0xae The buggy address belongs to the object at ffff888171306800 which belongs to the cache kmalloc-256 of size 256 The buggy address is located 36 bytes to the right of 256-byte region [ffff888171306800, ffff888171306900) The buggy address belongs to the page: page:00000000bcfb624e refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x171306 head:00000000bcfb624e order:1 compound_mapcount:0 flags: 0x17ffffc0010200(slab|head|node=0|zone=2|lastcpupid=0x1fffff) raw: 0017ffffc0010200 dead000000000100 dead000000000122 ffff888100042b40 raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff888171306800: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff888171306880: 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc fc >ffff888171306900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffff888171306980: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff888171306a00: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fix fq_pie traffic path to avoid selecting 'q->flows + q->flows_cnt' as a valid flow: it's an address beyond the allocated memory.

An out-of-bounds read vulnerability was found in smb2_dump_detail in fs/smb/client/smb2ops.c in the Linux Kernel. This issue could allow a local attacker to crash the system or leak internal kernel information.

In the Linux kernel, the following vulnerability has been resolved: netlabel: fix out-of-bounds memory accesses There are two array out-of-bounds memory accesses, one in cipso_v4_map_lvl_valid(), the other in netlbl_bitmap_walk(). Both errors are embarassingly simple, and the fixes are straightforward. As a FYI for anyone backporting this patch to kernels prior to v4.8, you'll want to apply the netlbl_bitmap_walk() patch to cipso_v4_bitmap_walk() as netlbl_bitmap_walk() doesn't exist before Linux v4.8.

In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Fix stack-out-of-bounds memory access from ioapic_write_indirect() KASAN reports the following issue: BUG: KASAN: stack-out-of-bounds in kvm_make_vcpus_request_mask+0x174/0x440 [kvm] Read of size 8 at addr ffffc9001364f638 by task qemu-kvm/4798 CPU: 0 PID: 4798 Comm: qemu-kvm Tainted: G X --------- --- Hardware name: AMD Corporation DAYTONA_X/DAYTONA_X, BIOS RYM0081C 07/13/2020 Call Trace: dump_stack+0xa5/0xe6 print_address_description.constprop.0+0x18/0x130 ? kvm_make_vcpus_request_mask+0x174/0x440 [kvm] __kasan_report.cold+0x7f/0x114 ? kvm_make_vcpus_request_mask+0x174/0x440 [kvm] kasan_report+0x38/0x50 kasan_check_range+0xf5/0x1d0 kvm_make_vcpus_request_mask+0x174/0x440 [kvm] kvm_make_scan_ioapic_request_mask+0x84/0xc0 [kvm] ? kvm_arch_exit+0x110/0x110 [kvm] ? sched_clock+0x5/0x10 ioapic_write_indirect+0x59f/0x9e0 [kvm] ? static_obj+0xc0/0xc0 ? __lock_acquired+0x1d2/0x8c0 ? kvm_ioapic_eoi_inject_work+0x120/0x120 [kvm] The problem appears to be that 'vcpu_bitmap' is allocated as a single long on stack and it should really be KVM_MAX_VCPUS long. We also seem to clear the lower 16 bits of it with bitmap_zero() for no particular reason (my guess would be that 'bitmap' and 'vcpu_bitmap' variables in kvm_bitmap_or_dest_vcpus() caused the confusion: while the later is indeed 16-bit long, the later should accommodate all possible vCPUs).

In the Linux kernel, the following vulnerability has been resolved: xfrm: state: fix out-of-bounds read during lookup lookup and resize can run in parallel. The xfrm_state_hash_generation seqlock ensures a retry, but the hash functions can observe a hmask value that is too large for the new hlist array. rehash does: rcu_assign_pointer(net->xfrm.state_bydst, ndst) [..] net->xfrm.state_hmask = nhashmask; While state lookup does: h = xfrm_dst_hash(net, daddr, saddr, tmpl->reqid, encap_family); hlist_for_each_entry_rcu(x, net->xfrm.state_bydst + h, bydst) { This is only safe in case the update to state_bydst is larger than net->xfrm.xfrm_state_hmask (or if the lookup function gets serialized via state spinlock again). Fix this by prefetching state_hmask and the associated pointers. The xfrm_state_hash_generation seqlock retry will ensure that the pointer and the hmask will be consistent. The existing helpers, like xfrm_dst_hash(), are now unsafe for RCU side, add lockdep assertions to document that they are only safe for insert side. xfrm_state_lookup_byaddr() uses the spinlock rather than RCU. AFAICS this is an oversight from back when state lookup was converted to RCU, this lock should be replaced with RCU in a future patch.

In the Linux kernel, the following vulnerability has been resolved: HID: intel-ish-hid: ipc: Disable and reenable ACPI GPE bit The EHL (Elkhart Lake) based platforms provide a OOB (Out of band) service, which allows to wakup device when the system is in S5 (Soft-Off state). This OOB service can be enabled/disabled from BIOS settings. When enabled, the ISH device gets PME wake capability. To enable PME wakeup, driver also needs to enable ACPI GPE bit. On resume, BIOS will clear the wakeup bit. So driver need to re-enable it in resume function to keep the next wakeup capability. But this BIOS clearing of wakeup bit doesn't decrement internal OS GPE reference count, so this reenabling on every resume will cause reference count to overflow. So first disable and reenable ACPI GPE bit using acpi_disable_gpe().

In the Linux kernel, the following vulnerability has been resolved: x86/CPU/AMD: Terminate the erratum_1386_microcode array The erratum_1386_microcode array requires an empty entry at the end. Otherwise x86_match_cpu_with_stepping() will continue iterate the array after it ended. Add an empty entry to erratum_1386_microcode to its end.

In the Linux kernel, the following vulnerability has been resolved: objtool, nvmet: Fix out-of-bounds stack access in nvmet_ctrl_state_show() The csts_state_names[] array only has six sparse entries, but the iteration code in nvmet_ctrl_state_show() iterates seven, resulting in a potential out-of-bounds stack read. Fix that. Fixes the following warning with an UBSAN kernel: vmlinux.o: warning: objtool: .text.nvmet_ctrl_state_show: unexpected end of section

In the Linux kernel, the following vulnerability has been resolved: jfs: fix out-of-bounds in dbNextAG() and diAlloc() In dbNextAG() , there is no check for the case where bmp->db_numag is greater or same than MAXAG due to a polluted image, which causes an out-of-bounds. Therefore, a bounds check should be added in dbMount(). And in dbNextAG(), a check for the case where agpref is greater than bmp->db_numag should be added, so an out-of-bounds exception should be prevented. Additionally, a check for the case where agno is greater or same than MAXAG should be added in diAlloc() to prevent out-of-bounds.

In the Linux kernel, the following vulnerability has been resolved: wifi: rtw89: remove unused C2H event ID RTW89_MAC_C2H_FUNC_READ_WOW_CAM to prevent out-of-bounds reading The handler of firmware C2H event RTW89_MAC_C2H_FUNC_READ_WOW_CAM isn't implemented, but driver expects number of handlers is NUM_OF_RTW89_MAC_C2H_FUNC_WOW causing out-of-bounds access. Fix it by removing ID. Addresses-Coverity-ID: 1598775 ("Out-of-bounds read")

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix potential oob read in nilfs_btree_check_delete() The function nilfs_btree_check_delete(), which checks whether degeneration to direct mapping occurs before deleting a b-tree entry, causes memory access outside the block buffer when retrieving the maximum key if the root node has no entries. This does not usually happen because b-tree mappings with 0 child nodes are never created by mkfs.nilfs2 or nilfs2 itself. However, it can happen if the b-tree root node read from a device is configured that way, so fix this potential issue by adding a check for that case.

An out-of-bounds read vulnerability was found in smbCalcSize in fs/smb/client/netmisc.c in the Linux Kernel. This issue could allow a local attacker to crash the system or leak internal kernel information.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix ucode out-of-bounds read warning Clear warning that read ucode[] may out-of-bounds.

In the Linux kernel, the following vulnerability has been resolved: ext4: fix OOB read when checking dotdot dir Mounting a corrupted filesystem with directory which contains '.' dir entry with rec_len == block size results in out-of-bounds read (later on, when the corrupted directory is removed). ext4_empty_dir() assumes every ext4 directory contains at least '.' and '..' as directory entries in the first data block. It first loads the '.' dir entry, performs sanity checks by calling ext4_check_dir_entry() and then uses its rec_len member to compute the location of '..' dir entry (in ext4_next_entry). It assumes the '..' dir entry fits into the same data block. If the rec_len of '.' is precisely one block (4KB), it slips through the sanity checks (it is considered the last directory entry in the data block) and leaves "struct ext4_dir_entry_2 *de" point exactly past the memory slot allocated to the data block. The following call to ext4_check_dir_entry() on new value of de then dereferences this pointer which results in out-of-bounds mem access. Fix this by extending __ext4_check_dir_entry() to check for '.' dir entries that reach the end of data block. Make sure to ignore the phony dir entries for checksum (by checking name_len for non-zero). Note: This is reported by KASAN as use-after-free in case another structure was recently freed from the slot past the bound, but it is really an OOB read. This issue was found by syzkaller tool. Call Trace: [ 38.594108] BUG: KASAN: slab-use-after-free in __ext4_check_dir_entry+0x67e/0x710 [ 38.594649] Read of size 2 at addr ffff88802b41a004 by task syz-executor/5375 [ 38.595158] [ 38.595288] CPU: 0 UID: 0 PID: 5375 Comm: syz-executor Not tainted 6.14.0-rc7 #1 [ 38.595298] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014 [ 38.595304] Call Trace: [ 38.595308] <TASK> [ 38.595311] dump_stack_lvl+0xa7/0xd0 [ 38.595325] print_address_description.constprop.0+0x2c/0x3f0 [ 38.595339] ? __ext4_check_dir_entry+0x67e/0x710 [ 38.595349] print_report+0xaa/0x250 [ 38.595359] ? __ext4_check_dir_entry+0x67e/0x710 [ 38.595368] ? kasan_addr_to_slab+0x9/0x90 [ 38.595378] kasan_report+0xab/0xe0 [ 38.595389] ? __ext4_check_dir_entry+0x67e/0x710 [ 38.595400] __ext4_check_dir_entry+0x67e/0x710 [ 38.595410] ext4_empty_dir+0x465/0x990 [ 38.595421] ? __pfx_ext4_empty_dir+0x10/0x10 [ 38.595432] ext4_rmdir.part.0+0x29a/0xd10 [ 38.595441] ? __dquot_initialize+0x2a7/0xbf0 [ 38.595455] ? __pfx_ext4_rmdir.part.0+0x10/0x10 [ 38.595464] ? __pfx___dquot_initialize+0x10/0x10 [ 38.595478] ? down_write+0xdb/0x140 [ 38.595487] ? __pfx_down_write+0x10/0x10 [ 38.595497] ext4_rmdir+0xee/0x140 [ 38.595506] vfs_rmdir+0x209/0x670 [ 38.595517] ? lookup_one_qstr_excl+0x3b/0x190 [ 38.595529] do_rmdir+0x363/0x3c0 [ 38.595537] ? __pfx_do_rmdir+0x10/0x10 [ 38.595544] ? strncpy_from_user+0x1ff/0x2e0 [ 38.595561] __x64_sys_unlinkat+0xf0/0x130 [ 38.595570] do_syscall_64+0x5b/0x180 [ 38.595583] entry_SYSCALL_64_after_hwframe+0x76/0x7e

In the Linux kernel, the following vulnerability has been resolved: HID: cougar: fix slab-out-of-bounds Read in cougar_report_fixup report_fixup for the Cougar 500k Gaming Keyboard was not verifying that the report descriptor size was correct before accessing it

In the Linux kernel, the following vulnerability has been resolved: media: uvcvideo: Fix OOB read If the index provided by the user is bigger than the mask size, we might do an out of bound read.

In the Linux kernel, the following vulnerability has been resolved: ring-buffer: Do not attempt to read past "commit" When iterating over the ring buffer while the ring buffer is active, the writer can corrupt the reader. There's barriers to help detect this and handle it, but that code missed the case where the last event was at the very end of the page and has only 4 bytes left. The checks to detect the corruption by the writer to reads needs to see the length of the event. If the length in the first 4 bytes is zero then the length is stored in the second 4 bytes. But if the writer is in the process of updating that code, there's a small window where the length in the first 4 bytes could be zero even though the length is only 4 bytes. That will cause rb_event_length() to read the next 4 bytes which could happen to be off the allocated page. To protect against this, fail immediately if the next event pointer is less than 8 bytes from the end of the commit (last byte of data), as all events must be a minimum of 8 bytes anyway.

In the Linux kernel, the following vulnerability has been resolved: nfc: nci: assert requested protocol is valid The protocol is used in a bit mask to determine if the protocol is supported. Assert the provided protocol is less than the maximum defined so it doesn't potentially perform a shift-out-of-bounds and provide a clearer error for undefined protocols vs unsupported ones.

In the Linux kernel, the following vulnerability has been resolved: wifi: mwifiex: Fix oob check condition in mwifiex_process_rx_packet Only skip the code path trying to access the rfc1042 headers when the buffer is too small, so the driver can still process packets without rfc1042 headers.

In the Linux kernel, the following vulnerability has been resolved: s390/ptrace: handle setting of fpc register correctly If the content of the floating point control (fpc) register of a traced process is modified with the ptrace interface the new value is tested for validity by temporarily loading it into the fpc register. This may lead to corruption of the fpc register of the tracing process: if an interrupt happens while the value is temporarily loaded into the fpc register, and within interrupt context floating point or vector registers are used, the current fp/vx registers are saved with save_fpu_regs() assuming they belong to user space and will be loaded into fp/vx registers when returning to user space. test_fp_ctl() restores the original user space fpc register value, however it will be discarded, when returning to user space. In result the tracer will incorrectly continue to run with the value that was supposed to be used for the traced process. Fix this by saving fpu register contents with save_fpu_regs() before using test_fp_ctl().

In the Linux kernel, the following vulnerability has been resolved: x86/alternatives: Disable KASAN in apply_alternatives() Fei has reported that KASAN triggers during apply_alternatives() on a 5-level paging machine: BUG: KASAN: out-of-bounds in rcu_is_watching() Read of size 4 at addr ff110003ee6419a0 by task swapper/0/0 ... __asan_load4() rcu_is_watching() trace_hardirqs_on() text_poke_early() apply_alternatives() ... On machines with 5-level paging, cpu_feature_enabled(X86_FEATURE_LA57) gets patched. It includes KASAN code, where KASAN_SHADOW_START depends on __VIRTUAL_MASK_SHIFT, which is defined with cpu_feature_enabled(). KASAN gets confused when apply_alternatives() patches the KASAN_SHADOW_START users. A test patch that makes KASAN_SHADOW_START static, by replacing __VIRTUAL_MASK_SHIFT with 56, works around the issue. Fix it for real by disabling KASAN while the kernel is patching alternatives. [ mingo: updated the changelog ]

In the Linux kernel, the following vulnerability has been resolved: thermal: intel: powerclamp: fix mismatch in get function for max_idle KASAN reported this [ 444.853098] BUG: KASAN: global-out-of-bounds in param_get_int+0x77/0x90 [ 444.853111] Read of size 4 at addr ffffffffc16c9220 by task cat/2105 ... [ 444.853442] The buggy address belongs to the variable: [ 444.853443] max_idle+0x0/0xffffffffffffcde0 [intel_powerclamp] There is a mismatch between the param_get_int and the definition of max_idle. Replacing param_get_int with param_get_byte resolves this issue.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix operation precedence bug in port timestamping napi_poll context Indirection (*) is of lower precedence than postfix increment (++). Logic in napi_poll context would cause an out-of-bound read by first increment the pointer address by byte address space and then dereference the value. Rather, the intended logic was to dereference first and then increment the underlying value.

In the Linux kernel, the following vulnerability has been resolved: i3c: mipi-i3c-hci: Fix out of bounds access in hci_dma_irq_handler Do not loop over ring headers in hci_dma_irq_handler() that are not allocated and enabled in hci_dma_init(). Otherwise out of bounds access will occur from rings->headers[i] access when i >= number of allocated ring headers.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: fix possible out-of-bound read in ath12k_htt_pull_ppdu_stats() len is extracted from HTT message and could be an unexpected value in case errors happen, so add validation before using to avoid possible out-of-bound read in the following message iteration and parsing. The same issue also applies to ppdu_info->ppdu_stats.common.num_users, so validate it before using too. These are found during code review. Compile test only.

In the Linux kernel, the following vulnerability has been resolved: netfilter: x_tables: fix LED ID check in led_tg_check() Syzbot has reported the following BUG detected by KASAN: BUG: KASAN: slab-out-of-bounds in strlen+0x58/0x70 Read of size 1 at addr ffff8881022da0c8 by task repro/5879 ... Call Trace: <TASK> dump_stack_lvl+0x241/0x360 ? __pfx_dump_stack_lvl+0x10/0x10 ? __pfx__printk+0x10/0x10 ? _printk+0xd5/0x120 ? __virt_addr_valid+0x183/0x530 ? __virt_addr_valid+0x183/0x530 print_report+0x169/0x550 ? __virt_addr_valid+0x183/0x530 ? __virt_addr_valid+0x183/0x530 ? __virt_addr_valid+0x45f/0x530 ? __phys_addr+0xba/0x170 ? strlen+0x58/0x70 kasan_report+0x143/0x180 ? strlen+0x58/0x70 strlen+0x58/0x70 kstrdup+0x20/0x80 led_tg_check+0x18b/0x3c0 xt_check_target+0x3bb/0xa40 ? __pfx_xt_check_target+0x10/0x10 ? stack_depot_save_flags+0x6e4/0x830 ? nft_target_init+0x174/0xc30 nft_target_init+0x82d/0xc30 ? __pfx_nft_target_init+0x10/0x10 ? nf_tables_newrule+0x1609/0x2980 ? nf_tables_newrule+0x1609/0x2980 ? rcu_is_watching+0x15/0xb0 ? nf_tables_newrule+0x1609/0x2980 ? nf_tables_newrule+0x1609/0x2980 ? __kmalloc_noprof+0x21a/0x400 nf_tables_newrule+0x1860/0x2980 ? __pfx_nf_tables_newrule+0x10/0x10 ? __nla_parse+0x40/0x60 nfnetlink_rcv+0x14e5/0x2ab0 ? __pfx_validate_chain+0x10/0x10 ? __pfx_nfnetlink_rcv+0x10/0x10 ? __lock_acquire+0x1384/0x2050 ? netlink_deliver_tap+0x2e/0x1b0 ? __pfx_lock_release+0x10/0x10 ? netlink_deliver_tap+0x2e/0x1b0 netlink_unicast+0x7f8/0x990 ? __pfx_netlink_unicast+0x10/0x10 ? __virt_addr_valid+0x183/0x530 ? __check_object_size+0x48e/0x900 netlink_sendmsg+0x8e4/0xcb0 ? __pfx_netlink_sendmsg+0x10/0x10 ? aa_sock_msg_perm+0x91/0x160 ? __pfx_netlink_sendmsg+0x10/0x10 __sock_sendmsg+0x223/0x270 ____sys_sendmsg+0x52a/0x7e0 ? __pfx_____sys_sendmsg+0x10/0x10 __sys_sendmsg+0x292/0x380 ? __pfx___sys_sendmsg+0x10/0x10 ? lockdep_hardirqs_on_prepare+0x43d/0x780 ? __pfx_lockdep_hardirqs_on_prepare+0x10/0x10 ? exc_page_fault+0x590/0x8c0 ? do_syscall_64+0xb6/0x230 do_syscall_64+0xf3/0x230 entry_SYSCALL_64_after_hwframe+0x77/0x7f ... </TASK> Since an invalid (without '\0' byte at all) byte sequence may be passed from userspace, add an extra check to ensure that such a sequence is rejected as possible ID and so never passed to 'kstrdup()' and further.

In the Linux kernel, the following vulnerability has been resolved: ice: Fix increasing MSI-X on VF Increasing MSI-X value on a VF leads to invalid memory operations. This is caused by not reallocating some arrays. Reproducer: modprobe ice echo 0 > /sys/bus/pci/devices/$PF_PCI/sriov_drivers_autoprobe echo 1 > /sys/bus/pci/devices/$PF_PCI/sriov_numvfs echo 17 > /sys/bus/pci/devices/$VF0_PCI/sriov_vf_msix_count Default MSI-X is 16, so 17 and above triggers this issue. KASAN reports: BUG: KASAN: slab-out-of-bounds in ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice] Read of size 8 at addr ffff8888b937d180 by task bash/28433 (...) Call Trace: (...) ? ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice] kasan_report+0xed/0x120 ? ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice] ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice] ice_vsi_cfg_def+0x3360/0x4770 [ice] ? mutex_unlock+0x83/0xd0 ? __pfx_ice_vsi_cfg_def+0x10/0x10 [ice] ? __pfx_ice_remove_vsi_lkup_fltr+0x10/0x10 [ice] ice_vsi_cfg+0x7f/0x3b0 [ice] ice_vf_reconfig_vsi+0x114/0x210 [ice] ice_sriov_set_msix_vec_count+0x3d0/0x960 [ice] sriov_vf_msix_count_store+0x21c/0x300 (...) Allocated by task 28201: (...) ice_vsi_cfg_def+0x1c8e/0x4770 [ice] ice_vsi_cfg+0x7f/0x3b0 [ice] ice_vsi_setup+0x179/0xa30 [ice] ice_sriov_configure+0xcaa/0x1520 [ice] sriov_numvfs_store+0x212/0x390 (...) To fix it, use ice_vsi_rebuild() instead of ice_vf_reconfig_vsi(). This causes the required arrays to be reallocated taking the new queue count into account (ice_vsi_realloc_stat_arrays()). Set req_txq and req_rxq before ice_vsi_rebuild(), so that realloc uses the newly set queue count. Additionally, ice_vsi_rebuild() does not remove VSI filters (ice_fltr_remove_all()), so ice_vf_init_host_cfg() is no longer necessary.