In the Linux kernel, the following vulnerability has been resolved: vxlan: Fix NPD in {arp,neigh}_reduce() when using nexthop objects When the "proxy" option is enabled on a VXLAN device, the device will suppress ARP requests and IPv6 Neighbor Solicitation messages if it is able to reply on behalf of the remote host. That is, if a matching and valid neighbor entry is configured on the VXLAN device whose MAC address is not behind the "any" remote (0.0.0.0 / ::). The code currently assumes that the FDB entry for the neighbor's MAC address points to a valid remote destination, but this is incorrect if the entry is associated with an FDB nexthop group. This can result in a NPD [1][3] which can be reproduced using [2][4]. Fix by checking that the remote destination exists before dereferencing it. [1] BUG: kernel NULL pointer dereference, address: 0000000000000000 [...] CPU: 4 UID: 0 PID: 365 Comm: arping Not tainted 6.17.0-rc2-virtme-g2a89cb21162c #2 PREEMPT(voluntary) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-4.fc41 04/01/2014 RIP: 0010:vxlan_xmit+0xb58/0x15f0 [...] Call Trace: <TASK> dev_hard_start_xmit+0x5d/0x1c0 __dev_queue_xmit+0x246/0xfd0 packet_sendmsg+0x113a/0x1850 __sock_sendmsg+0x38/0x70 __sys_sendto+0x126/0x180 __x64_sys_sendto+0x24/0x30 do_syscall_64+0xa4/0x260 entry_SYSCALL_64_after_hwframe+0x4b/0x53 [2] #!/bin/bash ip address add 192.0.2.1/32 dev lo ip nexthop add id 1 via 192.0.2.2 fdb ip nexthop add id 10 group 1 fdb ip link add name vx0 up type vxlan id 10010 local 192.0.2.1 dstport 4789 proxy ip neigh add 192.0.2.3 lladdr 00:11:22:33:44:55 nud perm dev vx0 bridge fdb add 00:11:22:33:44:55 dev vx0 self static nhid 10 arping -b -c 1 -s 192.0.2.1 -I vx0 192.0.2.3 [3] BUG: kernel NULL pointer dereference, address: 0000000000000000 [...] CPU: 13 UID: 0 PID: 372 Comm: ndisc6 Not tainted 6.17.0-rc2-virtmne-g6ee90cb26014 #3 PREEMPT(voluntary) Hardware name: QEMU Standard PC (i440FX + PIIX, 1v996), BIOS 1.17.0-4.fc41 04/01/2x014 RIP: 0010:vxlan_xmit+0x803/0x1600 [...] Call Trace: <TASK> dev_hard_start_xmit+0x5d/0x1c0 __dev_queue_xmit+0x246/0xfd0 ip6_finish_output2+0x210/0x6c0 ip6_finish_output+0x1af/0x2b0 ip6_mr_output+0x92/0x3e0 ip6_send_skb+0x30/0x90 rawv6_sendmsg+0xe6e/0x12e0 __sock_sendmsg+0x38/0x70 __sys_sendto+0x126/0x180 __x64_sys_sendto+0x24/0x30 do_syscall_64+0xa4/0x260 entry_SYSCALL_64_after_hwframe+0x4b/0x53 RIP: 0033:0x7f383422ec77 [4] #!/bin/bash ip address add 2001:db8:1::1/128 dev lo ip nexthop add id 1 via 2001:db8:1::1 fdb ip nexthop add id 10 group 1 fdb ip link add name vx0 up type vxlan id 10010 local 2001:db8:1::1 dstport 4789 proxy ip neigh add 2001:db8:1::3 lladdr 00:11:22:33:44:55 nud perm dev vx0 bridge fdb add 00:11:22:33:44:55 dev vx0 self static nhid 10 ndisc6 -r 1 -s 2001:db8:1::1 -w 1 2001:db8:1::3 vx0

In the Linux kernel, the following vulnerability has been resolved: crypto: ccp - Always pass in an error pointer to __sev_platform_shutdown_locked() When 9770b428b1a2 ("crypto: ccp - Move dev_info/err messages for SEV/SNP init and shutdown") moved the error messages dumping so that they don't need to be issued by the callers, it missed the case where __sev_firmware_shutdown() calls __sev_platform_shutdown_locked() with a NULL argument which leads to a NULL ptr deref on the shutdown path, during suspend to disk: #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: Oops: 0000 [#1] SMP NOPTI CPU: 0 UID: 0 PID: 983 Comm: hib.sh Not tainted 6.17.0-rc4+ #1 PREEMPT(voluntary) Hardware name: Supermicro Super Server/H12SSL-i, BIOS 2.5 09/08/2022 RIP: 0010:__sev_platform_shutdown_locked.cold+0x0/0x21 [ccp] That rIP is: 00000000000006fd <__sev_platform_shutdown_locked.cold>: 6fd: 8b 13 mov (%rbx),%edx 6ff: 48 8b 7d 00 mov 0x0(%rbp),%rdi 703: 89 c1 mov %eax,%ecx Code: 74 05 31 ff 41 89 3f 49 8b 3e 89 ea 48 c7 c6 a0 8e 54 a0 41 bf 92 ff ff ff e8 e5 2e 09 e1 c6 05 2a d4 38 00 01 e9 26 af ff ff <8b> 13 48 8b 7d 00 89 c1 48 c7 c6 18 90 54 a0 89 44 24 04 e8 c1 2e RSP: 0018:ffffc90005467d00 EFLAGS: 00010282 RAX: 00000000ffffff92 RBX: 0000000000000000 RCX: 0000000000000000 ^^^^^^^^^^^^^^^^ and %rbx is nice and clean. Call Trace: <TASK> __sev_firmware_shutdown.isra.0 sev_dev_destroy psp_dev_destroy sp_destroy pci_device_shutdown device_shutdown kernel_power_off hibernate.cold state_store kernfs_fop_write_iter vfs_write ksys_write do_syscall_64 entry_SYSCALL_64_after_hwframe Pass in a pointer to the function-local error var in the caller. With that addressed, suspending the ccp shows the error properly at least: ccp 0000:47:00.1: sev command 0x2 timed out, disabling PSP ccp 0000:47:00.1: SEV: failed to SHUTDOWN error 0x0, rc -110 SEV-SNP: Leaking PFN range 0x146800-0x146a00 SEV-SNP: PFN 0x146800 unassigned, dumping non-zero entries in 2M PFN region: [0x146800 - 0x146a00] ... ccp 0000:47:00.1: SEV-SNP firmware shutdown failed, rc -16, error 0x0 ACPI: PM: Preparing to enter system sleep state S5 kvm: exiting hardware virtualization reboot: Power down Btw, this driver is crying to be cleaned up to pass in a proper I/O struct which can be used to store information between the different functions, otherwise stuff like that will happen in the future again.

In the Linux kernel, the following vulnerability has been resolved: ceph: always call ceph_shift_unused_folios_left() The function ceph_process_folio_batch() sets folio_batch entries to NULL, which is an illegal state. Before folio_batch_release() crashes due to this API violation, the function ceph_shift_unused_folios_left() is supposed to remove those NULLs from the array. However, since commit ce80b76dd327 ("ceph: introduce ceph_process_folio_batch() method"), this shifting doesn't happen anymore because the "for" loop got moved to ceph_process_folio_batch(), and now the `i` variable that remains in ceph_writepages_start() doesn't get incremented anymore, making the shifting effectively unreachable much of the time. Later, commit 1551ec61dc55 ("ceph: introduce ceph_submit_write() method") added more preconditions for doing the shift, replacing the `i` check (with something that is still just as broken): - if ceph_process_folio_batch() fails, shifting never happens - if ceph_move_dirty_page_in_page_array() was never called (because ceph_process_folio_batch() has returned early for some of various reasons), shifting never happens - if `processed_in_fbatch` is zero (because ceph_process_folio_batch() has returned early for some of the reasons mentioned above or because ceph_move_dirty_page_in_page_array() has failed), shifting never happens Since those two commits, any problem in ceph_process_folio_batch() could crash the kernel, e.g. this way: BUG: kernel NULL pointer dereference, address: 0000000000000034 #PF: supervisor write access in kernel mode #PF: error_code(0x0002) - not-present page PGD 0 P4D 0 Oops: Oops: 0002 [#1] SMP NOPTI CPU: 172 UID: 0 PID: 2342707 Comm: kworker/u778:8 Not tainted 6.15.10-cm4all1-es #714 NONE Hardware name: Dell Inc. PowerEdge R7615/0G9DHV, BIOS 1.6.10 12/08/2023 Workqueue: writeback wb_workfn (flush-ceph-1) RIP: 0010:folios_put_refs+0x85/0x140 Code: 83 c5 01 39 e8 7e 76 48 63 c5 49 8b 5c c4 08 b8 01 00 00 00 4d 85 ed 74 05 41 8b 44 ad 00 48 8b 15 b0 > RSP: 0018:ffffb880af8db778 EFLAGS: 00010207 RAX: 0000000000000001 RBX: 0000000000000000 RCX: 0000000000000003 RDX: ffffe377cc3b0000 RSI: 0000000000000000 RDI: ffffb880af8db8c0 RBP: 0000000000000000 R08: 000000000000007d R09: 000000000102b86f R10: 0000000000000001 R11: 00000000000000ac R12: ffffb880af8db8c0 R13: 0000000000000000 R14: 0000000000000000 R15: ffff9bd262c97000 FS: 0000000000000000(0000) GS:ffff9c8efc303000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000034 CR3: 0000000160958004 CR4: 0000000000770ef0 PKRU: 55555554 Call Trace: <TASK> ceph_writepages_start+0xeb9/0x1410 The crash can be reproduced easily by changing the ceph_check_page_before_write() return value to `-E2BIG`. (Interestingly, the crash happens only if `huge_zero_folio` has already been allocated; without `huge_zero_folio`, is_huge_zero_folio(NULL) returns true and folios_put_refs() skips NULL entries instead of dereferencing them. That makes reproducing the bug somewhat unreliable. See https://lore.kernel.org/20250826231626.218675-1-max.kellermann@ionos.com for a discussion of this detail.) My suggestion is to move the ceph_shift_unused_folios_left() to right after ceph_process_folio_batch() to ensure it always gets called to fix up the illegal folio_batch state.

In the Linux kernel, the following vulnerability has been resolved: vxlan: Fix NPD when refreshing an FDB entry with a nexthop object VXLAN FDB entries can point to either a remote destination or an FDB nexthop group. The latter is usually used in EVPN deployments where learning is disabled. However, when learning is enabled, an incoming packet might try to refresh an FDB entry that points to an FDB nexthop group and therefore does not have a remote. Such packets should be dropped, but they are only dropped after dereferencing the non-existent remote, resulting in a NPD [1] which can be reproduced using [2]. Fix by dropping such packets earlier. Remove the misleading comment from first_remote_rcu(). [1] BUG: kernel NULL pointer dereference, address: 0000000000000000 [...] CPU: 13 UID: 0 PID: 361 Comm: mausezahn Not tainted 6.17.0-rc1-virtme-g9f6b606b6b37 #1 PREEMPT(voluntary) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-4.fc41 04/01/2014 RIP: 0010:vxlan_snoop+0x98/0x1e0 [...] Call Trace: <TASK> vxlan_encap_bypass+0x209/0x240 encap_bypass_if_local+0xb1/0x100 vxlan_xmit_one+0x1375/0x17e0 vxlan_xmit+0x6b4/0x15f0 dev_hard_start_xmit+0x5d/0x1c0 __dev_queue_xmit+0x246/0xfd0 packet_sendmsg+0x113a/0x1850 __sock_sendmsg+0x38/0x70 __sys_sendto+0x126/0x180 __x64_sys_sendto+0x24/0x30 do_syscall_64+0xa4/0x260 entry_SYSCALL_64_after_hwframe+0x4b/0x53 [2] #!/bin/bash ip address add 192.0.2.1/32 dev lo ip address add 192.0.2.2/32 dev lo ip nexthop add id 1 via 192.0.2.3 fdb ip nexthop add id 10 group 1 fdb ip link add name vx0 up type vxlan id 10010 local 192.0.2.1 dstport 12345 localbypass ip link add name vx1 up type vxlan id 10020 local 192.0.2.2 dstport 54321 learning bridge fdb add 00:11:22:33:44:55 dev vx0 self static dst 192.0.2.2 port 54321 vni 10020 bridge fdb add 00:aa:bb:cc:dd:ee dev vx1 self static nhid 10 mausezahn vx0 -a 00:aa:bb:cc:dd:ee -b 00:11:22:33:44:55 -c 1 -q

In the Linux kernel, the following vulnerability has been resolved: of_numa: fix uninitialized memory nodes causing kernel panic When there are memory-only nodes (nodes without CPUs), these nodes are not properly initialized, causing kernel panic during boot. of_numa_init of_numa_parse_cpu_nodes node_set(nid, numa_nodes_parsed); of_numa_parse_memory_nodes In of_numa_parse_cpu_nodes, numa_nodes_parsed gets updated only for nodes containing CPUs. Memory-only nodes should have been updated in of_numa_parse_memory_nodes, but they weren't. Subsequently, when free_area_init() attempts to access NODE_DATA() for these uninitialized memory nodes, the kernel panics due to NULL pointer dereference. This can be reproduced on ARM64 QEMU with 1 CPU and 2 memory nodes: qemu-system-aarch64 \ -cpu host -nographic \ -m 4G -smp 1 \ -machine virt,accel=kvm,gic-version=3,iommu=smmuv3 \ -object memory-backend-ram,size=2G,id=mem0 \ -object memory-backend-ram,size=2G,id=mem1 \ -numa node,nodeid=0,memdev=mem0 \ -numa node,nodeid=1,memdev=mem1 \ -kernel $IMAGE \ -hda $DISK \ -append "console=ttyAMA0 root=/dev/vda rw earlycon" [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x481fd010] [ 0.000000] Linux version 6.17.0-rc1-00001-gabb4b3daf18c-dirty (yintirui@local) (gcc (GCC) 12.3.1, GNU ld (GNU Binutils) 2.41) #52 SMP PREEMPT Mon Aug 18 09:49:40 CST 2025 [ 0.000000] KASLR enabled [ 0.000000] random: crng init done [ 0.000000] Machine model: linux,dummy-virt [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: pl11 at MMIO 0x0000000009000000 (options '') [ 0.000000] printk: legacy bootconsole [pl11] enabled [ 0.000000] OF: reserved mem: Reserved memory: No reserved-memory node in the DT [ 0.000000] NODE_DATA(0) allocated [mem 0xbfffd9c0-0xbfffffff] [ 0.000000] node 1 must be removed before remove section 23 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x000000013fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] node 1: [mem 0x00000000c0000000-0x000000013fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000a0 [ 0.000000] Mem abort info: [ 0.000000] ESR = 0x0000000096000004 [ 0.000000] EC = 0x25: DABT (current EL), IL = 32 bits [ 0.000000] SET = 0, FnV = 0 [ 0.000000] EA = 0, S1PTW = 0 [ 0.000000] FSC = 0x04: level 0 translation fault [ 0.000000] Data abort info: [ 0.000000] ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 [ 0.000000] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 0.000000] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 0.000000] [00000000000000a0] user address but active_mm is swapper [ 0.000000] Internal error: Oops: 0000000096000004 [#1] SMP [ 0.000000] Modules linked in: [ 0.000000] CPU: 0 UID: 0 PID: 0 Comm: swapper Not tainted 6.17.0-rc1-00001-g760c6dabf762-dirty #54 PREEMPT [ 0.000000] Hardware name: linux,dummy-virt (DT) [ 0.000000] pstate: 800000c5 (Nzcv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 0.000000] pc : free_area_init+0x50c/0xf9c [ 0.000000] lr : free_area_init+0x5c0/0xf9c [ 0.000000] sp : ffffa02ca0f33c00 [ 0.000000] x29: ffffa02ca0f33cb0 x28: 0000000000000000 x27: 0000000000000000 [ 0.000000] x26: 4ec4ec4ec4ec4ec5 x25: 00000000000c0000 x24: 00000000000c0000 [ 0.000000] x23: 0000000000040000 x22: 0000000000000000 x21: ffffa02ca0f3b368 [ 0.000000] x20: ffffa02ca14c7b98 x19: 0000000000000000 x18: 0000000000000002 [ 0.000000] x17: 000000000000cacc x16: 0000000000000001 x15: 0000000000000001 [ 0.000000] x14: 0000000080000000 x13: 0000000000000018 x12: 0000000000000002 [ 0.0 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: devlink: fix xa_alloc_cyclic() error handling In case of returning 1 from xa_alloc_cyclic() (wrapping) ERR_PTR(1) will be returned, which will cause IS_ERR() to be false. Which can lead to dereference not allocated pointer (rel). Fix it by checking if err is lower than zero. This wasn't found in real usecase, only noticed. Credit to Pierre.

In the Linux kernel, the following vulnerability has been resolved: mm/slub: avoid accessing metadata when pointer is invalid in object_err() object_err() reports details of an object for further debugging, such as the freelist pointer, redzone, etc. However, if the pointer is invalid, attempting to access object metadata can lead to a crash since it does not point to a valid object. One known path to the crash is when alloc_consistency_checks() determines the pointer to the allocated object is invalid because of a freelist corruption, and calls object_err() to report it. The debug code should report and handle the corruption gracefully and not crash in the process. In case the pointer is NULL or check_valid_pointer() returns false for the pointer, only print the pointer value and skip accessing metadata.

In the Linux kernel, the following vulnerability has been resolved: wifi: brcmfmac: Check the return value of of_property_read_string_index() Somewhen between 6.10 and 6.11 the driver started to crash on my MacBookPro14,3. The property doesn't exist and 'tmp' remains uninitialized, so we pass a random pointer to devm_kstrdup(). The crash I am getting looks like this: BUG: unable to handle page fault for address: 00007f033c669379 PF: supervisor read access in kernel mode PF: error_code(0x0001) - permissions violation PGD 8000000101341067 P4D 8000000101341067 PUD 101340067 PMD 1013bb067 PTE 800000010aee9025 Oops: Oops: 0001 [#1] SMP PTI CPU: 4 UID: 0 PID: 827 Comm: (udev-worker) Not tainted 6.11.8-gentoo #1 Hardware name: Apple Inc. MacBookPro14,3/Mac-551B86E5744E2388, BIOS 529.140.2.0.0 06/23/2024 RIP: 0010:strlen+0x4/0x30 Code: f7 75 ec 31 c0 c3 cc cc cc cc 48 89 f8 c3 cc cc cc cc 0f 1f 40 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 f3 0f 1e fa <80> 3f 00 74 14 48 89 f8 48 83 c0 01 80 38 00 75 f7 48 29 f8 c3 cc RSP: 0018:ffffb4aac0683ad8 EFLAGS: 00010202 RAX: 00000000ffffffea RBX: 00007f033c669379 RCX: 0000000000000001 RDX: 0000000000000cc0 RSI: 00007f033c669379 RDI: 00007f033c669379 RBP: 00000000ffffffea R08: 0000000000000000 R09: 00000000c0ba916a R10: ffffffffffffffff R11: ffffffffb61ea260 R12: ffff91f7815b50c8 R13: 0000000000000cc0 R14: ffff91fafefffe30 R15: ffffb4aac0683b30 FS: 00007f033ccbe8c0(0000) GS:ffff91faeed00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f033c669379 CR3: 0000000107b1e004 CR4: 00000000003706f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? __die+0x23/0x70 ? page_fault_oops+0x149/0x4c0 ? raw_spin_rq_lock_nested+0xe/0x20 ? sched_balance_newidle+0x22b/0x3c0 ? update_load_avg+0x78/0x770 ? exc_page_fault+0x6f/0x150 ? asm_exc_page_fault+0x26/0x30 ? __pfx_pci_conf1_write+0x10/0x10 ? strlen+0x4/0x30 devm_kstrdup+0x25/0x70 brcmf_of_probe+0x273/0x350 [brcmfmac]

In the Linux kernel, the following vulnerability has been resolved: igb: Fix NULL pointer dereference in ethtool loopback test The igb driver currently causes a NULL pointer dereference when executing the ethtool loopback test. This occurs because there is no associated q_vector for the test ring when it is set up, as interrupts are typically not added to the test rings. Since commit 5ef44b3cb43b removed the napi_id assignment in __xdp_rxq_info_reg(), there is no longer a need to pass a napi_id to it. Therefore, simply use 0 as the last parameter.

In the Linux kernel, the following vulnerability has been resolved: sctp: sysctl: rto_min/max: avoid using current->nsproxy As mentioned in a previous commit of this series, using the 'net' structure via 'current' is not recommended for different reasons: - Inconsistency: getting info from the reader's/writer's netns vs only from the opener's netns. - current->nsproxy can be NULL in some cases, resulting in an 'Oops' (null-ptr-deref), e.g. when the current task is exiting, as spotted by syzbot [1] using acct(2). The 'net' structure can be obtained from the table->data using container_of(). Note that table->data could also be used directly, as this is the only member needed from the 'net' structure, but that would increase the size of this fix, to use '*data' everywhere 'net->sctp.rto_min/max' is used.

In the Linux kernel, the following vulnerability has been resolved: net: ethernet: ti: am65-cpsw-nuss: Fix null pointer dereference for ndev In the TX completion packet stage of TI SoCs with CPSW2G instance, which has single external ethernet port, ndev is accessed without being initialized if no TX packets have been processed. It results into null pointer dereference, causing kernel to crash. Fix this by having a check on the number of TX packets which have been processed.

In the Linux kernel, the following vulnerability has been resolved: pcmcia: Fix a NULL pointer dereference in __iodyn_find_io_region() In __iodyn_find_io_region(), pcmcia_make_resource() is assigned to res and used in pci_bus_alloc_resource(). There is a dereference of res in pci_bus_alloc_resource(), which could lead to a NULL pointer dereference on failure of pcmcia_make_resource(). Fix this bug by adding a check of res.

In the Linux kernel, the following vulnerability has been resolved: net: rfkill: gpio: Fix crash due to dereferencering uninitialized pointer Since commit 7d5e9737efda ("net: rfkill: gpio: get the name and type from device property") rfkill_find_type() gets called with the possibly uninitialized "const char *type_name;" local variable. On x86 systems when rfkill-gpio binds to a "BCM4752" or "LNV4752" acpi_device, the rfkill->type is set based on the ACPI acpi_device_id: rfkill->type = (unsigned)id->driver_data; and there is no "type" property so device_property_read_string() will fail and leave type_name uninitialized, leading to a potential crash. rfkill_find_type() does accept a NULL pointer, fix the potential crash by initializing type_name to NULL. Note likely sofar this has not been caught because: 1. Not many x86 machines actually have a "BCM4752"/"LNV4752" acpi_device 2. The stack happened to contain NULL where type_name is stored

In the Linux kernel, the following vulnerability has been resolved: net: xilinx: axienet: Add error handling for RX metadata pointer retrieval Add proper error checking for dmaengine_desc_get_metadata_ptr() which can return an error pointer and lead to potential crashes or undefined behaviour if the pointer retrieval fails. Properly handle the error by unmapping DMA buffer, freeing the skb and returning early to prevent further processing with invalid data.

In the Linux kernel, the following vulnerability has been resolved: drm: bridge: anx7625: Fix NULL pointer dereference with early IRQ If the interrupt occurs before resource initialization is complete, the interrupt handler/worker may access uninitialized data such as the I2C tcpc_client device, potentially leading to NULL pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: cifs: prevent NULL pointer dereference in UTF16 conversion There can be a NULL pointer dereference bug here. NULL is passed to __cifs_sfu_make_node without checks, which passes it unchecked to cifs_strndup_to_utf16, which in turn passes it to cifs_local_to_utf16_bytes where '*from' is dereferenced, causing a crash. This patch adds a check for NULL 'src' in cifs_strndup_to_utf16 and returns NULL early to prevent dereferencing NULL pointer. Found by Linux Verification Center (linuxtesting.org) with SVACE

In the Linux kernel, the following vulnerability has been resolved: eth: mlx4: Fix IS_ERR() vs NULL check bug in mlx4_en_create_rx_ring Replace NULL check with IS_ERR() check after calling page_pool_create() since this function returns error pointers (ERR_PTR). Using NULL check could lead to invalid pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: pcmcia: Add error handling for add_interval() in do_validate_mem() In the do_validate_mem(), the call to add_interval() does not handle errors. If kmalloc() fails in add_interval(), it could result in a null pointer being inserted into the linked list, leading to illegal memory access when sub_interval() is called next. This patch adds an error handling for the add_interval(). If add_interval() returns an error, the function will return early with the error code.

In the Linux kernel, the following vulnerability has been resolved: media: imx-jpeg: Fix potential error pointer dereference in detach_pm() The proble is on the first line: if (jpeg->pd_dev[i] && !pm_runtime_suspended(jpeg->pd_dev[i])) If jpeg->pd_dev[i] is an error pointer, then passing it to pm_runtime_suspended() will lead to an Oops. The other conditions check for both error pointers and NULL, but it would be more clear to use the IS_ERR_OR_NULL() check for that.

In the Linux kernel, the following vulnerability has been resolved: ASoC: qcom: q6apm-lpass-dais: Fix NULL pointer dereference if source graph failed If earlier opening of source graph fails (e.g. ADSP rejects due to incorrect audioreach topology), the graph is closed and "dai_data->graph[dai->id]" is assigned NULL. Preparing the DAI for sink graph continues though and next call to q6apm_lpass_dai_prepare() receives dai_data->graph[dai->id]=NULL leading to NULL pointer exception: qcom-apm gprsvc:service:2:1: Error (1) Processing 0x01001002 cmd qcom-apm gprsvc:service:2:1: DSP returned error[1001002] 1 q6apm-lpass-dais 30000000.remoteproc:glink-edge:gpr:service@1:bedais: fail to start APM port 78 q6apm-lpass-dais 30000000.remoteproc:glink-edge:gpr:service@1:bedais: ASoC: error at snd_soc_pcm_dai_prepare on TX_CODEC_DMA_TX_3: -22 Unable to handle kernel NULL pointer dereference at virtual address 00000000000000a8 ... Call trace: q6apm_graph_media_format_pcm+0x48/0x120 (P) q6apm_lpass_dai_prepare+0x110/0x1b4 snd_soc_pcm_dai_prepare+0x74/0x108 __soc_pcm_prepare+0x44/0x160 dpcm_be_dai_prepare+0x124/0x1c0

In the Linux kernel, the following vulnerability has been resolved: ceph: fix crash after fscrypt_encrypt_pagecache_blocks() error The function move_dirty_folio_in_page_array() was created by commit ce80b76dd327 ("ceph: introduce ceph_process_folio_batch() method") by moving code from ceph_writepages_start() to this function. This new function is supposed to return an error code which is checked by the caller (now ceph_process_folio_batch()), and on error, the caller invokes redirty_page_for_writepage() and then breaks from the loop. However, the refactoring commit has gone wrong, and it by accident, it always returns 0 (= success) because it first NULLs the pointer and then returns PTR_ERR(NULL) which is always 0. This means errors are silently ignored, leaving NULL entries in the page array, which may later crash the kernel. The simple solution is to call PTR_ERR() before clearing the pointer.

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: tests: Fix potential NULL dereference in test_cfg80211_parse_colocated_ap() kunit_kzalloc() may return NULL, dereferencing it without NULL check may lead to NULL dereference. Add a NULL check for ies.

In the Linux kernel, the following vulnerability has been resolved: net/smc: fix one NULL pointer dereference in smc_ib_is_sg_need_sync() BUG: kernel NULL pointer dereference, address: 00000000000002ec PGD 0 P4D 0 Oops: Oops: 0000 [#1] SMP PTI CPU: 28 UID: 0 PID: 343 Comm: kworker/28:1 Kdump: loaded Tainted: G OE 6.17.0-rc2+ #9 NONE Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.15.0-1 04/01/2014 Workqueue: smc_hs_wq smc_listen_work [smc] RIP: 0010:smc_ib_is_sg_need_sync+0x9e/0xd0 [smc] ... Call Trace: <TASK> smcr_buf_map_link+0x211/0x2a0 [smc] __smc_buf_create+0x522/0x970 [smc] smc_buf_create+0x3a/0x110 [smc] smc_find_rdma_v2_device_serv+0x18f/0x240 [smc] ? smc_vlan_by_tcpsk+0x7e/0xe0 [smc] smc_listen_find_device+0x1dd/0x2b0 [smc] smc_listen_work+0x30f/0x580 [smc] process_one_work+0x18c/0x340 worker_thread+0x242/0x360 kthread+0xe7/0x220 ret_from_fork+0x13a/0x160 ret_from_fork_asm+0x1a/0x30 </TASK> If the software RoCE device is used, ibdev->dma_device is a null pointer. As a result, the problem occurs. Null pointer detection is added to prevent problems.

In the Linux kernel, the following vulnerability has been resolved: devlink: rate: Unset parent pointer in devl_rate_nodes_destroy The function devl_rate_nodes_destroy is documented to "Unset parent for all rate objects". However, it was only calling the driver-specific `rate_leaf_parent_set` or `rate_node_parent_set` ops and decrementing the parent's refcount, without actually setting the `devlink_rate->parent` pointer to NULL. This leaves a dangling pointer in the `devlink_rate` struct, which cause refcount error in netdevsim[1] and mlx5[2]. In addition, this is inconsistent with the behavior of `devlink_nl_rate_parent_node_set`, where the parent pointer is correctly cleared. This patch fixes the issue by explicitly setting `devlink_rate->parent` to NULL after notifying the driver, thus fulfilling the function's documented behavior for all rate objects. [1] repro steps: echo 1 > /sys/bus/netdevsim/new_device devlink dev eswitch set netdevsim/netdevsim1 mode switchdev echo 1 > /sys/bus/netdevsim/devices/netdevsim1/sriov_numvfs devlink port function rate add netdevsim/netdevsim1/test_node devlink port function rate set netdevsim/netdevsim1/128 parent test_node echo 1 > /sys/bus/netdevsim/del_device dmesg: refcount_t: decrement hit 0; leaking memory. WARNING: CPU: 8 PID: 1530 at lib/refcount.c:31 refcount_warn_saturate+0x42/0xe0 CPU: 8 UID: 0 PID: 1530 Comm: bash Not tainted 6.18.0-rc4+ #1 NONE Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 RIP: 0010:refcount_warn_saturate+0x42/0xe0 Call Trace: <TASK> devl_rate_leaf_destroy+0x8d/0x90 __nsim_dev_port_del+0x6c/0x70 [netdevsim] nsim_dev_reload_destroy+0x11c/0x140 [netdevsim] nsim_drv_remove+0x2b/0xb0 [netdevsim] device_release_driver_internal+0x194/0x1f0 bus_remove_device+0xc6/0x130 device_del+0x159/0x3c0 device_unregister+0x1a/0x60 del_device_store+0x111/0x170 [netdevsim] kernfs_fop_write_iter+0x12e/0x1e0 vfs_write+0x215/0x3d0 ksys_write+0x5f/0xd0 do_syscall_64+0x55/0x10f0 entry_SYSCALL_64_after_hwframe+0x4b/0x53 [2] devlink dev eswitch set pci/0000:08:00.0 mode switchdev devlink port add pci/0000:08:00.0 flavour pcisf pfnum 0 sfnum 1000 devlink port function rate add pci/0000:08:00.0/group1 devlink port function rate set pci/0000:08:00.0/32768 parent group1 modprobe -r mlx5_ib mlx5_fwctl mlx5_core dmesg: refcount_t: decrement hit 0; leaking memory. WARNING: CPU: 7 PID: 16151 at lib/refcount.c:31 refcount_warn_saturate+0x42/0xe0 CPU: 7 UID: 0 PID: 16151 Comm: bash Not tainted 6.17.0-rc7_for_upstream_min_debug_2025_10_02_12_44 #1 NONE Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014 RIP: 0010:refcount_warn_saturate+0x42/0xe0 Call Trace: <TASK> devl_rate_leaf_destroy+0x8d/0x90 mlx5_esw_offloads_devlink_port_unregister+0x33/0x60 [mlx5_core] mlx5_esw_offloads_unload_rep+0x3f/0x50 [mlx5_core] mlx5_eswitch_unload_sf_vport+0x40/0x90 [mlx5_core] mlx5_sf_esw_event+0xc4/0x120 [mlx5_core] notifier_call_chain+0x33/0xa0 blocking_notifier_call_chain+0x3b/0x50 mlx5_eswitch_disable_locked+0x50/0x110 [mlx5_core] mlx5_eswitch_disable+0x63/0x90 [mlx5_core] mlx5_unload+0x1d/0x170 [mlx5_core] mlx5_uninit_one+0xa2/0x130 [mlx5_core] remove_one+0x78/0xd0 [mlx5_core] pci_device_remove+0x39/0xa0 device_release_driver_internal+0x194/0x1f0 unbind_store+0x99/0xa0 kernfs_fop_write_iter+0x12e/0x1e0 vfs_write+0x215/0x3d0 ksys_write+0x5f/0xd0 do_syscall_64+0x53/0x1f0 entry_SYSCALL_64_after_hwframe+0x4b/0x53

In the Linux kernel, the following vulnerability has been resolved: net: fec: Fix possible NPD in fec_enet_phy_reset_after_clk_enable() The function of_phy_find_device may return NULL, so we need to take care before dereferencing phy_dev.

In the Linux kernel, the following vulnerability has been resolved: soc: aspeed: lpc-snoop: Don't disable channels that aren't enabled Mitigate e.g. the following: # echo 1e789080.lpc-snoop > /sys/bus/platform/drivers/aspeed-lpc-snoop/unbind ... [ 120.363594] Unable to handle kernel NULL pointer dereference at virtual address 00000004 when write [ 120.373866] [00000004] *pgd=00000000 [ 120.377910] Internal error: Oops: 805 [#1] SMP ARM [ 120.383306] CPU: 1 UID: 0 PID: 315 Comm: sh Not tainted 6.15.0-rc1-00009-g926217bc7d7d-dirty #20 NONE ... [ 120.679543] Call trace: [ 120.679559] misc_deregister from aspeed_lpc_snoop_remove+0x84/0xac [ 120.692462] aspeed_lpc_snoop_remove from platform_remove+0x28/0x38 [ 120.700996] platform_remove from device_release_driver_internal+0x188/0x200 ...

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: remove oem i2c adapter on finish Fixes a bug where unbinding of the GPU would leave the oem i2c adapter registered resulting in a null pointer dereference when applications try to access the invalid device. (cherry picked from commit 89923fb7ead4fdd37b78dd49962d9bb5892403e6)

In the Linux kernel, the following vulnerability has been resolved: firmware: qcom: scm: Fix missing read barrier in qcom_scm_get_tzmem_pool() Commit 2e4955167ec5 ("firmware: qcom: scm: Fix __scm and waitq completion variable initialization") introduced a write barrier in probe function to store global '__scm' variable. We all known barriers are paired (see memory-barriers.txt: "Note that write barriers should normally be paired with read or address-dependency barriers"), therefore accessing it from concurrent contexts requires read barrier. Previous commit added such barrier in qcom_scm_is_available(), so let's use that directly. Lack of this read barrier can result in fetching stale '__scm' variable value, NULL, and dereferencing it. Note that barrier in qcom_scm_is_available() satisfies here the control dependency.

In the Linux kernel, the following vulnerability has been resolved: tee: fix NULL pointer dereference in tee_shm_put tee_shm_put have NULL pointer dereference: __optee_disable_shm_cache --> shm = reg_pair_to_ptr(...);//shm maybe return NULL tee_shm_free(shm); --> tee_shm_put(shm);//crash Add check in tee_shm_put to fix it. panic log: Unable to handle kernel paging request at virtual address 0000000000100cca Mem abort info: ESR = 0x0000000096000004 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x04: level 0 translation fault Data abort info: ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 CM = 0, WnR = 0, TnD = 0, TagAccess = 0 GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 user pgtable: 4k pages, 48-bit VAs, pgdp=0000002049d07000 [0000000000100cca] pgd=0000000000000000, p4d=0000000000000000 Internal error: Oops: 0000000096000004 [#1] SMP CPU: 2 PID: 14442 Comm: systemd-sleep Tainted: P OE ------- ---- 6.6.0-39-generic #38 Source Version: 938b255f6cb8817c95b0dd5c8c2944acfce94b07 Hardware name: greatwall GW-001Y1A-FTH, BIOS Great Wall BIOS V3.0 10/26/2022 pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : tee_shm_put+0x24/0x188 lr : tee_shm_free+0x14/0x28 sp : ffff001f98f9faf0 x29: ffff001f98f9faf0 x28: ffff0020df543cc0 x27: 0000000000000000 x26: ffff001f811344a0 x25: ffff8000818dac00 x24: ffff800082d8d048 x23: ffff001f850fcd18 x22: 0000000000000001 x21: ffff001f98f9fb88 x20: ffff001f83e76218 x19: ffff001f83e761e0 x18: 000000000000ffff x17: 303a30303a303030 x16: 0000000000000000 x15: 0000000000000003 x14: 0000000000000001 x13: 0000000000000000 x12: 0101010101010101 x11: 0000000000000001 x10: 0000000000000001 x9 : ffff800080e08d0c x8 : ffff001f98f9fb88 x7 : 0000000000000000 x6 : 0000000000000000 x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000 x2 : ffff001f83e761e0 x1 : 00000000ffff001f x0 : 0000000000100cca Call trace: tee_shm_put+0x24/0x188 tee_shm_free+0x14/0x28 __optee_disable_shm_cache+0xa8/0x108 optee_shutdown+0x28/0x38 platform_shutdown+0x28/0x40 device_shutdown+0x144/0x2b0 kernel_power_off+0x3c/0x80 hibernate+0x35c/0x388 state_store+0x64/0x80 kobj_attr_store+0x14/0x28 sysfs_kf_write+0x48/0x60 kernfs_fop_write_iter+0x128/0x1c0 vfs_write+0x270/0x370 ksys_write+0x6c/0x100 __arm64_sys_write+0x20/0x30 invoke_syscall+0x4c/0x120 el0_svc_common.constprop.0+0x44/0xf0 do_el0_svc+0x24/0x38 el0_svc+0x24/0x88 el0t_64_sync_handler+0x134/0x150 el0t_64_sync+0x14c/0x15

In the Linux kernel, the following vulnerability has been resolved: net/tcp: Fix a NULL pointer dereference when using TCP-AO with TCP_REPAIR A NULL pointer dereference can occur in tcp_ao_finish_connect() during a connect() system call on a socket with a TCP-AO key added and TCP_REPAIR enabled. The function is called with skb being NULL and attempts to dereference it on tcp_hdr(skb)->seq without a prior skb validation. Fix this by checking if skb is NULL before dereferencing it. The commentary is taken from bpf_skops_established(), which is also called in the same flow. Unlike the function being patched, bpf_skops_established() validates the skb before dereferencing it. int main(void){ struct sockaddr_in sockaddr; struct tcp_ao_add tcp_ao; int sk; int one = 1; memset(&sockaddr,'\0',sizeof(sockaddr)); memset(&tcp_ao,'\0',sizeof(tcp_ao)); sk = socket(AF_INET, SOCK_STREAM, IPPROTO_TCP); sockaddr.sin_family = AF_INET; memcpy(tcp_ao.alg_name,"cmac(aes128)",12); memcpy(tcp_ao.key,"ABCDEFGHABCDEFGH",16); tcp_ao.keylen = 16; memcpy(&tcp_ao.addr,&sockaddr,sizeof(sockaddr)); setsockopt(sk, IPPROTO_TCP, TCP_AO_ADD_KEY, &tcp_ao, sizeof(tcp_ao)); setsockopt(sk, IPPROTO_TCP, TCP_REPAIR, &one, sizeof(one)); sockaddr.sin_family = AF_INET; sockaddr.sin_port = htobe16(123); inet_aton("127.0.0.1", &sockaddr.sin_addr); connect(sk,(struct sockaddr *)&sockaddr,sizeof(sockaddr)); return 0; } $ gcc tcp-ao-nullptr.c -o tcp-ao-nullptr -Wall $ unshare -Urn BUG: kernel NULL pointer dereference, address: 00000000000000b6 PGD 1f648d067 P4D 1f648d067 PUD 1982e8067 PMD 0 Oops: Oops: 0000 [#1] SMP NOPTI Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 11/12/2020 RIP: 0010:tcp_ao_finish_connect (net/ipv4/tcp_ao.c:1182)

In the Linux kernel, the following vulnerability has been resolved: gpio: grgpio: Add NULL check in grgpio_probe devm_kasprintf() can return a NULL pointer on failure,but this returned value in grgpio_probe is not checked. Add NULL check in grgpio_probe, to handle kernel NULL pointer dereference error.

In the Linux kernel, the following vulnerability has been resolved: ALSA: usb: scarlett2: Fix missing NULL check scarlett2_input_select_ctl_info() sets up the string arrays allocated via kasprintf(), but it misses NULL checks, which may lead to NULL dereference Oops. Let's add the proper NULL check.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: fix a NULL pointer dereference in amdgpu_dm_i2c_xfer() When ddc_service_construct() is called, it explicitly checks both the link type and whether there is something on the link which will dictate whether the pin is marked as hw_supported. If the pin isn't set or the link is not set (such as from unloading/reloading amdgpu in an IGT test) then fail the amdgpu_dm_i2c_xfer() call.

In the Linux kernel, the following vulnerability has been resolved: s390/sclp: Fix SCCB present check Tracing code called by the SCLP interrupt handler contains early exits if the SCCB address associated with an interrupt is NULL. This check is performed after physical to virtual address translation. If the kernel identity mapping does not start at address zero, the resulting virtual address is never zero, so that the NULL checks won't work. Subsequently this may result in incorrect accesses to the first page of the identity mapping. Fix this by introducing a function that handles the NULL case before address translation.

In the Linux kernel, the following vulnerability has been resolved: KVM: SVM: Reject SEV{-ES} intra host migration if vCPU creation is in-flight Reject migration of SEV{-ES} state if either the source or destination VM is actively creating a vCPU, i.e. if kvm_vm_ioctl_create_vcpu() is in the section between incrementing created_vcpus and online_vcpus. The bulk of vCPU creation runs _outside_ of kvm->lock to allow creating multiple vCPUs in parallel, and so sev_info.es_active can get toggled from false=>true in the destination VM after (or during) svm_vcpu_create(), resulting in an SEV{-ES} VM effectively having a non-SEV{-ES} vCPU. The issue manifests most visibly as a crash when trying to free a vCPU's NULL VMSA page in an SEV-ES VM, but any number of things can go wrong. BUG: unable to handle page fault for address: ffffebde00000000 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: Oops: 0000 [#1] SMP KASAN NOPTI CPU: 227 UID: 0 PID: 64063 Comm: syz.5.60023 Tainted: G U O 6.15.0-smp-DEV #2 NONE Tainted: [U]=USER, [O]=OOT_MODULE Hardware name: Google, Inc. Arcadia_IT_80/Arcadia_IT_80, BIOS 12.52.0-0 10/28/2024 RIP: 0010:constant_test_bit arch/x86/include/asm/bitops.h:206 [inline] RIP: 0010:arch_test_bit arch/x86/include/asm/bitops.h:238 [inline] RIP: 0010:_test_bit include/asm-generic/bitops/instrumented-non-atomic.h:142 [inline] RIP: 0010:PageHead include/linux/page-flags.h:866 [inline] RIP: 0010:___free_pages+0x3e/0x120 mm/page_alloc.c:5067 Code: <49> f7 06 40 00 00 00 75 05 45 31 ff eb 0c 66 90 4c 89 f0 4c 39 f0 RSP: 0018:ffff8984551978d0 EFLAGS: 00010246 RAX: 0000777f80000001 RBX: 0000000000000000 RCX: ffffffff918aeb98 RDX: 0000000000000000 RSI: 0000000000000008 RDI: ffffebde00000000 RBP: 0000000000000000 R08: ffffebde00000007 R09: 1ffffd7bc0000000 R10: dffffc0000000000 R11: fffff97bc0000001 R12: dffffc0000000000 R13: ffff8983e19751a8 R14: ffffebde00000000 R15: 1ffffd7bc0000000 FS: 0000000000000000(0000) GS:ffff89ee661d3000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffebde00000000 CR3: 000000793ceaa000 CR4: 0000000000350ef0 DR0: 0000000000000000 DR1: 0000000000000b5f DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Call Trace: <TASK> sev_free_vcpu+0x413/0x630 arch/x86/kvm/svm/sev.c:3169 svm_vcpu_free+0x13a/0x2a0 arch/x86/kvm/svm/svm.c:1515 kvm_arch_vcpu_destroy+0x6a/0x1d0 arch/x86/kvm/x86.c:12396 kvm_vcpu_destroy virt/kvm/kvm_main.c:470 [inline] kvm_destroy_vcpus+0xd1/0x300 virt/kvm/kvm_main.c:490 kvm_arch_destroy_vm+0x636/0x820 arch/x86/kvm/x86.c:12895 kvm_put_kvm+0xb8e/0xfb0 virt/kvm/kvm_main.c:1310 kvm_vm_release+0x48/0x60 virt/kvm/kvm_main.c:1369 __fput+0x3e4/0x9e0 fs/file_table.c:465 task_work_run+0x1a9/0x220 kernel/task_work.c:227 exit_task_work include/linux/task_work.h:40 [inline] do_exit+0x7f0/0x25b0 kernel/exit.c:953 do_group_exit+0x203/0x2d0 kernel/exit.c:1102 get_signal+0x1357/0x1480 kernel/signal.c:3034 arch_do_signal_or_restart+0x40/0x690 arch/x86/kernel/signal.c:337 exit_to_user_mode_loop kernel/entry/common.c:111 [inline] exit_to_user_mode_prepare include/linux/entry-common.h:329 [inline] __syscall_exit_to_user_mode_work kernel/entry/common.c:207 [inline] syscall_exit_to_user_mode+0x67/0xb0 kernel/entry/common.c:218 do_syscall_64+0x7c/0x150 arch/x86/entry/syscall_64.c:100 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7f87a898e969 </TASK> Modules linked in: gq(O) gsmi: Log Shutdown Reason 0x03 CR2: ffffebde00000000 ---[ end trace 0000000000000000 ]--- Deliberately don't check for a NULL VMSA when freeing the vCPU, as crashing the host is likely desirable due to the VMSA being consumed by hardware. E.g. if KVM manages to allow VMRUN on the vCPU, hardware may read/write a bogus VMSA page. Accessing P ---truncated---

In the Linux kernel, the following vulnerability has been resolved: drm/mediatek: Add error handling for old state CRTC in atomic_disable Introduce error handling to address an issue where, after a hotplug event, the cursor continues to update. This situation can lead to a kernel panic due to accessing the NULL `old_state->crtc`. E,g. Unable to handle kernel NULL pointer dereference at virtual address Call trace: mtk_crtc_plane_disable+0x24/0x140 mtk_plane_atomic_update+0x8c/0xa8 drm_atomic_helper_commit_planes+0x114/0x2c8 drm_atomic_helper_commit_tail_rpm+0x4c/0x158 commit_tail+0xa0/0x168 drm_atomic_helper_commit+0x110/0x120 drm_atomic_commit+0x8c/0xe0 drm_atomic_helper_update_plane+0xd4/0x128 __setplane_atomic+0xcc/0x110 drm_mode_cursor_common+0x250/0x440 drm_mode_cursor_ioctl+0x44/0x70 drm_ioctl+0x264/0x5d8 __arm64_sys_ioctl+0xd8/0x510 invoke_syscall+0x6c/0xe0 do_el0_svc+0x68/0xe8 el0_svc+0x34/0x60 el0t_64_sync_handler+0x1c/0xf8 el0t_64_sync+0x180/0x188 Adding NULL pointer checks to ensure stability by preventing operations on an invalid CRTC state.

In the Linux kernel, the following vulnerability has been resolved: atm: clip: Fix potential null-ptr-deref in to_atmarpd(). atmarpd is protected by RTNL since commit f3a0592b37b8 ("[ATM]: clip causes unregister hang"). However, it is not enough because to_atmarpd() is called without RTNL, especially clip_neigh_solicit() / neigh_ops->solicit() is unsleepable. Also, there is no RTNL dependency around atmarpd. Let's use a private mutex and RCU to protect access to atmarpd in to_atmarpd().

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Avoid a NULL pointer dereference [WHY] Although unlikely drm_atomic_get_new_connector_state() or drm_atomic_get_old_connector_state() can return NULL. [HOW] Check returns before dereference. (cherry picked from commit 1e5e8d672fec9f2ab352be121be971877bff2af9)

In the Linux kernel, the following vulnerability has been resolved: staging: gpib: Fix cb7210 pcmcia Oops The pcmcia_driver struct was still only using the old .name initialization in the drv field. This led to a NULL pointer deref Oops in strcmp called from pcmcia_register_driver. Initialize the pcmcia_driver struct name field.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: fix a Null pointer dereference vulnerability [Why] A null pointer dereference vulnerability exists in the AMD display driver's (DC module) cleanup function dc_destruct(). When display control context (dc->ctx) construction fails (due to memory allocation failure), this pointer remains NULL. During subsequent error handling when dc_destruct() is called, there's no NULL check before dereferencing the perf_trace member (dc->ctx->perf_trace), causing a kernel null pointer dereference crash. [How] Check if dc->ctx is non-NULL before dereferencing. (Updated commit text and removed unnecessary error message) (cherry picked from commit 9dd8e2ba268c636c240a918e0a31e6feaee19404)

In the Linux kernel, the following vulnerability has been resolved: drm/msm/dpu: Add a null ptr check for dpu_encoder_needs_modeset The drm_atomic_get_new_connector_state() can return NULL if the connector is not part of the atomic state. Add a check to prevent a NULL pointer dereference. This follows the same pattern used in dpu_encoder_update_topology() within the same file, which checks for NULL before using conn_state. Patchwork: https://patchwork.freedesktop.org/patch/665188/

In the Linux kernel, the following vulnerability has been resolved: net: ethernet: rtsn: Fix a null pointer dereference in rtsn_probe() Add check for the return value of rcar_gen4_ptp_alloc() to prevent potential null pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: pinctrl: qcom: msm: mark certain pins as invalid for interrupts On some platforms, the UFS-reset pin has no interrupt logic in TLMM but is nevertheless registered as a GPIO in the kernel. This enables the user-space to trigger a BUG() in the pinctrl-msm driver by running, for example: `gpiomon -c 0 113` on RB2. The exact culprit is requesting pins whose intr_detection_width setting is not 1 or 2 for interrupts. This hits a BUG() in msm_gpio_irq_set_type(). Potentially crashing the kernel due to an invalid request from user-space is not optimal, so let's go through the pins and mark those that would fail the check as invalid for the irq chip as we should not even register them as available irqs. This function can be extended if we determine that there are more corner-cases like this.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix null pointer dereference error in generate_encryptionkey If client send two session setups with krb5 authenticate to ksmbd, null pointer dereference error in generate_encryptionkey could happen. sess->Preauth_HashValue is set to NULL if session is valid. So this patch skip generate encryption key if session is valid.

In the Linux kernel, the following vulnerability has been resolved: block: reject bs > ps block devices when THP is disabled If THP is disabled and when a block device with logical block size > page size is present, the following null ptr deref panic happens during boot: [ [13.2 mK AOSAN: null-ptr-deref in range [0x0000000000000000-0x0000000000K0 0 0[07] [ 13.017749] RIP: 0010:create_empty_buffers+0x3b/0x380 <snip> [ 13.025448] Call Trace: [ 13.025692] <TASK> [ 13.025895] block_read_full_folio+0x610/0x780 [ 13.026379] ? __pfx_blkdev_get_block+0x10/0x10 [ 13.027008] ? __folio_batch_add_and_move+0x1fa/0x2b0 [ 13.027548] ? __pfx_blkdev_read_folio+0x10/0x10 [ 13.028080] filemap_read_folio+0x9b/0x200 [ 13.028526] ? __pfx_filemap_read_folio+0x10/0x10 [ 13.029030] ? __filemap_get_folio+0x43/0x620 [ 13.029497] do_read_cache_folio+0x155/0x3b0 [ 13.029962] ? __pfx_blkdev_read_folio+0x10/0x10 [ 13.030381] read_part_sector+0xb7/0x2a0 [ 13.030805] read_lba+0x174/0x2c0 <snip> [ 13.045348] nvme_scan_ns+0x684/0x850 [nvme_core] [ 13.045858] ? __pfx_nvme_scan_ns+0x10/0x10 [nvme_core] [ 13.046414] ? _raw_spin_unlock+0x15/0x40 [ 13.046843] ? __switch_to+0x523/0x10a0 [ 13.047253] ? kvm_clock_get_cycles+0x14/0x30 [ 13.047742] ? __pfx_nvme_scan_ns_async+0x10/0x10 [nvme_core] [ 13.048353] async_run_entry_fn+0x96/0x4f0 [ 13.048787] process_one_work+0x667/0x10a0 [ 13.049219] worker_thread+0x63c/0xf60 As large folio support depends on THP, only allow bs > ps block devices if THP is enabled.

In the Linux kernel, the following vulnerability has been resolved: Revert "drm/gem-dma: Use dma_buf from GEM object instance" This reverts commit e8afa1557f4f963c9a511bd2c6074a941c308685. The dma_buf field in struct drm_gem_object is not stable over the object instance's lifetime. The field becomes NULL when user space releases the final GEM handle on the buffer object. This resulted in a NULL-pointer deref. Workarounds in commit 5307dce878d4 ("drm/gem: Acquire references on GEM handles for framebuffers") and commit f6bfc9afc751 ("drm/framebuffer: Acquire internal references on GEM handles") only solved the problem partially. They especially don't work for buffer objects without a DRM framebuffer associated. Hence, this revert to going back to using .import_attach->dmabuf. v3: - cc stable

In the Linux kernel, the following vulnerability has been resolved: drm/hisilicon/hibmc: fix the hibmc loaded failed bug When hibmc loaded failed, the driver use hibmc_unload to free the resource, but the mutexes in mode.config are not init, which will access an NULL pointer. Just change goto statement to return, because hibnc_hw_init() doesn't need to free anything.

In the Linux kernel, the following vulnerability has been resolved: power: supply: cpcap-charger: Fix null check for power_supply_get_by_name In the cpcap_usb_detect() function, the power_supply_get_by_name() function may return `NULL` instead of an error pointer. To prevent potential null pointer dereferences, Added a null check.

In the Linux kernel, the following vulnerability has been resolved: gfs2: No more self recovery When a node withdraws and it turns out that it is the only node that has the filesystem mounted, gfs2 currently tries to replay the local journal to bring the filesystem back into a consistent state. Not only is that a very bad idea, it has also never worked because gfs2_recover_func() will refuse to do anything during a withdraw. However, before even getting to this point, gfs2_recover_func() dereferences sdp->sd_jdesc->jd_inode. This was a use-after-free before commit 04133b607a78 ("gfs2: Prevent double iput for journal on error") and is a NULL pointer dereference since then. Simply get rid of self recovery to fix that.

In the Linux kernel, the following vulnerability has been resolved: ALSA: timer: fix ida_free call while not allocated In the snd_utimer_create() function, if the kasprintf() function return NULL, snd_utimer_put_id() will be called, finally use ida_free() to free the unallocated id 0. the syzkaller reported the following information: ------------[ cut here ]------------ ida_free called for id=0 which is not allocated. WARNING: CPU: 1 PID: 1286 at lib/idr.c:592 ida_free+0x1fd/0x2f0 lib/idr.c:592 Modules linked in: CPU: 1 UID: 0 PID: 1286 Comm: syz-executor164 Not tainted 6.15.8 #3 PREEMPT(lazy) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-4.fc42 04/01/2014 RIP: 0010:ida_free+0x1fd/0x2f0 lib/idr.c:592 Code: f8 fc 41 83 fc 3e 76 69 e8 70 b2 f8 (...) RSP: 0018:ffffc900007f79c8 EFLAGS: 00010282 RAX: 0000000000000000 RBX: 1ffff920000fef3b RCX: ffffffff872176a5 RDX: ffff88800369d200 RSI: 0000000000000000 RDI: ffff88800369d200 RBP: 0000000000000000 R08: ffffffff87ba60a5 R09: 0000000000000000 R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000000 R13: 0000000000000002 R14: 0000000000000000 R15: 0000000000000000 FS: 00007f6f1abc1740(0000) GS:ffff8880d76a0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f6f1ad7a784 CR3: 000000007a6e2000 CR4: 00000000000006f0 Call Trace: <TASK> snd_utimer_put_id sound/core/timer.c:2043 [inline] [snd_timer] snd_utimer_create+0x59b/0x6a0 sound/core/timer.c:2184 [snd_timer] snd_utimer_ioctl_create sound/core/timer.c:2202 [inline] [snd_timer] __snd_timer_user_ioctl.isra.0+0x724/0x1340 sound/core/timer.c:2287 [snd_timer] snd_timer_user_ioctl+0x75/0xc0 sound/core/timer.c:2298 [snd_timer] vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:907 [inline] __se_sys_ioctl fs/ioctl.c:893 [inline] __x64_sys_ioctl+0x198/0x200 fs/ioctl.c:893 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0x7b/0x160 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x76/0x7e [...] The utimer->id should be set properly before the kasprintf() function, ensures the snd_utimer_put_id() function will free the allocated id.