In the Linux kernel, the following vulnerability has been resolved: KVM: Destroy I/O bus devices on unregister failure _after_ sync'ing SRCU If allocating a new instance of an I/O bus fails when unregistering a device, wait to destroy the device until after all readers are guaranteed to see the new null bus. Destroying devices before the bus is nullified could lead to use-after-free since readers expect the devices on their reference of the bus to remain valid.

In the Linux kernel, the following vulnerability has been resolved: serial: liteuart: fix use-after-free and memleak on unbind Deregister the port when unbinding the driver to prevent it from being used after releasing the driver data and leaking memory allocated by serial core.

In the Linux kernel, the following vulnerability has been resolved: igc: Fix use-after-free error during reset Cleans the next descriptor to watch (next_to_watch) when cleaning the TX ring. Failure to do so can cause invalid memory accesses. If igc_poll() runs while the controller is being reset this can lead to the driver try to free a skb that was already freed. Log message: [ 101.525242] refcount_t: underflow; use-after-free. [ 101.525251] WARNING: CPU: 1 PID: 646 at lib/refcount.c:28 refcount_warn_saturate+0xab/0xf0 [ 101.525259] Modules linked in: sch_etf(E) sch_mqprio(E) rfkill(E) intel_rapl_msr(E) intel_rapl_common(E) x86_pkg_temp_thermal(E) intel_powerclamp(E) coretemp(E) binfmt_misc(E) kvm_intel(E) kvm(E) irqbypass(E) crc32_pclmul(E) ghash_clmulni_intel(E) aesni_intel(E) mei_wdt(E) libaes(E) crypto_simd(E) cryptd(E) glue_helper(E) snd_hda_codec_hdmi(E) rapl(E) intel_cstate(E) snd_hda_intel(E) snd_intel_dspcfg(E) sg(E) soundwire_intel(E) intel_uncore(E) at24(E) soundwire_generic_allocation(E) iTCO_wdt(E) soundwire_cadence(E) intel_pmc_bxt(E) serio_raw(E) snd_hda_codec(E) iTCO_vendor_support(E) watchdog(E) snd_hda_core(E) snd_hwdep(E) snd_soc_core(E) snd_compress(E) snd_pcsp(E) soundwire_bus(E) snd_pcm(E) evdev(E) snd_timer(E) mei_me(E) snd(E) soundcore(E) mei(E) configfs(E) ip_tables(E) x_tables(E) autofs4(E) ext4(E) crc32c_generic(E) crc16(E) mbcache(E) jbd2(E) sd_mod(E) t10_pi(E) crc_t10dif(E) crct10dif_generic(E) i915(E) ahci(E) libahci(E) ehci_pci(E) igb(E) xhci_pci(E) ehci_hcd(E) [ 101.525303] drm_kms_helper(E) dca(E) xhci_hcd(E) libata(E) crct10dif_pclmul(E) cec(E) crct10dif_common(E) tsn(E) igc(E) e1000e(E) ptp(E) i2c_i801(E) crc32c_intel(E) psmouse(E) i2c_algo_bit(E) i2c_smbus(E) scsi_mod(E) lpc_ich(E) pps_core(E) usbcore(E) drm(E) button(E) video(E) [ 101.525318] CPU: 1 PID: 646 Comm: irq/37-enp7s0-T Tainted: G E 5.10.30-rt37-tsn1-rt-ipipe #ipipe [ 101.525320] Hardware name: SIEMENS AG SIMATIC IPC427D/A5E31233588, BIOS V17.02.09 03/31/2017 [ 101.525322] RIP: 0010:refcount_warn_saturate+0xab/0xf0 [ 101.525325] Code: 05 31 48 44 01 01 e8 f0 c6 42 00 0f 0b c3 80 3d 1f 48 44 01 00 75 90 48 c7 c7 78 a8 f3 a6 c6 05 0f 48 44 01 01 e8 d1 c6 42 00 <0f> 0b c3 80 3d fe 47 44 01 00 0f 85 6d ff ff ff 48 c7 c7 d0 a8 f3 [ 101.525327] RSP: 0018:ffffbdedc0917cb8 EFLAGS: 00010286 [ 101.525329] RAX: 0000000000000000 RBX: ffff98fd6becbf40 RCX: 0000000000000001 [ 101.525330] RDX: 0000000000000001 RSI: ffffffffa6f2700c RDI: 00000000ffffffff [ 101.525332] RBP: ffff98fd6becc14c R08: ffffffffa7463d00 R09: ffffbdedc0917c50 [ 101.525333] R10: ffffffffa74c3578 R11: 0000000000000034 R12: 00000000ffffff00 [ 101.525335] R13: ffff98fd6b0b1000 R14: 0000000000000039 R15: ffff98fd6be35c40 [ 101.525337] FS: 0000000000000000(0000) GS:ffff98fd6e240000(0000) knlGS:0000000000000000 [ 101.525339] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 101.525341] CR2: 00007f34135a3a70 CR3: 0000000150210003 CR4: 00000000001706e0 [ 101.525343] Call Trace: [ 101.525346] sock_wfree+0x9c/0xa0 [ 101.525353] unix_destruct_scm+0x7b/0xa0 [ 101.525358] skb_release_head_state+0x40/0x90 [ 101.525362] skb_release_all+0xe/0x30 [ 101.525364] napi_consume_skb+0x57/0x160 [ 101.525367] igc_poll+0xb7/0xc80 [igc] [ 101.525376] ? sched_clock+0x5/0x10 [ 101.525381] ? sched_clock_cpu+0xe/0x100 [ 101.525385] net_rx_action+0x14c/0x410 [ 101.525388] __do_softirq+0xe9/0x2f4 [ 101.525391] __local_bh_enable_ip+0xe3/0x110 [ 101.525395] ? irq_finalize_oneshot.part.47+0xe0/0xe0 [ 101.525398] irq_forced_thread_fn+0x6a/0x80 [ 101.525401] irq_thread+0xe8/0x180 [ 101.525403] ? wake_threads_waitq+0x30/0x30 [ 101.525406] ? irq_thread_check_affinity+0xd0/0xd0 [ 101.525408] kthread+0x183/0x1a0 [ 101.525412] ? kthread_park+0x80/0x80 [ 101.525415] ret_from_fork+0x22/0x30

In the Linux kernel, the following vulnerability has been resolved: can: dev: can_restart: fix use after free bug After calling netif_rx_ni(skb), dereferencing skb is unsafe. Especially, the can_frame cf which aliases skb memory is accessed after the netif_rx_ni() in: stats->rx_bytes += cf->len; Reordering the lines solves the issue.

In the Linux kernel, the following vulnerability has been resolved: net: ti: fix UAF in tlan_remove_one priv is netdev private data and it cannot be used after free_netdev() call. Using priv after free_netdev() can cause UAF bug. Fix it by moving free_netdev() at the end of the function.

In the Linux kernel, the following vulnerability has been resolved: staging: greybus: uart: fix tty use after free User space can hold a tty open indefinitely and tty drivers must not release the underlying structures until the last user is gone. Switch to using the tty-port reference counter to manage the life time of the greybus tty state to avoid use after free after a disconnect.

In the Linux kernel, the following vulnerability has been resolved: igb: Fix use-after-free error during reset Cleans the next descriptor to watch (next_to_watch) when cleaning the TX ring. Failure to do so can cause invalid memory accesses. If igb_poll() runs while the controller is reset this can lead to the driver try to free a skb that was already freed. (The crash is harder to reproduce with the igb driver, but the same potential problem exists as the code is identical to igc)

In the Linux kernel, the following vulnerability has been resolved: can: j1939: j1939_netdev_start(): fix UAF for rx_kref of j1939_priv It will trigger UAF for rx_kref of j1939_priv as following. cpu0 cpu1 j1939_sk_bind(socket0, ndev0, ...) j1939_netdev_start j1939_sk_bind(socket1, ndev0, ...) j1939_netdev_start j1939_priv_set j1939_priv_get_by_ndev_locked j1939_jsk_add ..... j1939_netdev_stop kref_put_lock(&priv->rx_kref, ...) kref_get(&priv->rx_kref, ...) REFCOUNT_WARN("addition on 0;...") ==================================================== refcount_t: addition on 0; use-after-free. WARNING: CPU: 1 PID: 20874 at lib/refcount.c:25 refcount_warn_saturate+0x169/0x1e0 RIP: 0010:refcount_warn_saturate+0x169/0x1e0 Call Trace: j1939_netdev_start+0x68b/0x920 j1939_sk_bind+0x426/0xeb0 ? security_socket_bind+0x83/0xb0 The rx_kref's kref_get() and kref_put() should use j1939_netdev_lock to protect.

In the Linux kernel, the following vulnerability has been resolved: net: fddi: fix UAF in fza_probe fp is netdev private data and it cannot be used after free_netdev() call. Using fp after free_netdev() can cause UAF bug. Fix it by moving free_netdev() after error message. TURBOchannel adapter")

In the Linux kernel, the following vulnerability has been resolved: ACPI: custom_method: fix potential use-after-free issue In cm_write(), buf is always freed when reaching the end of the function. If the requested count is less than table.length, the allocated buffer will be freed but subsequent calls to cm_write() will still try to access it. Remove the unconditional kfree(buf) at the end of the function and set the buf to NULL in the -EINVAL error path to match the rest of function.

In the Linux kernel, the following vulnerability has been resolved: bpf: Track subprog poke descriptors correctly and fix use-after-free Subprograms are calling map_poke_track(), but on program release there is no hook to call map_poke_untrack(). However, on program release, the aux memory (and poke descriptor table) is freed even though we still have a reference to it in the element list of the map aux data. When we run map_poke_run(), we then end up accessing free'd memory, triggering KASAN in prog_array_map_poke_run(): [...] [ 402.824689] BUG: KASAN: use-after-free in prog_array_map_poke_run+0xc2/0x34e [ 402.824698] Read of size 4 at addr ffff8881905a7940 by task hubble-fgs/4337 [ 402.824705] CPU: 1 PID: 4337 Comm: hubble-fgs Tainted: G I 5.12.0+ #399 [ 402.824715] Call Trace: [ 402.824719] dump_stack+0x93/0xc2 [ 402.824727] print_address_description.constprop.0+0x1a/0x140 [ 402.824736] ? prog_array_map_poke_run+0xc2/0x34e [ 402.824740] ? prog_array_map_poke_run+0xc2/0x34e [ 402.824744] kasan_report.cold+0x7c/0xd8 [ 402.824752] ? prog_array_map_poke_run+0xc2/0x34e [ 402.824757] prog_array_map_poke_run+0xc2/0x34e [ 402.824765] bpf_fd_array_map_update_elem+0x124/0x1a0 [...] The elements concerned are walked as follows: for (i = 0; i < elem->aux->size_poke_tab; i++) { poke = &elem->aux->poke_tab[i]; [...] The access to size_poke_tab is a 4 byte read, verified by checking offsets in the KASAN dump: [ 402.825004] The buggy address belongs to the object at ffff8881905a7800 which belongs to the cache kmalloc-1k of size 1024 [ 402.825008] The buggy address is located 320 bytes inside of 1024-byte region [ffff8881905a7800, ffff8881905a7c00) The pahole output of bpf_prog_aux: struct bpf_prog_aux { [...] /* --- cacheline 5 boundary (320 bytes) --- */ u32 size_poke_tab; /* 320 4 */ [...] In general, subprograms do not necessarily manage their own data structures. For example, BTF func_info and linfo are just pointers to the main program structure. This allows reference counting and cleanup to be done on the latter which simplifies their management a bit. The aux->poke_tab struct, however, did not follow this logic. The initial proposed fix for this use-after-free bug further embedded poke data tracking into the subprogram with proper reference counting. However, Daniel and Alexei questioned why we were treating these objects special; I agree, its unnecessary. The fix here removes the per subprogram poke table allocation and map tracking and instead simply points the aux->poke_tab pointer at the main programs poke table. This way, map tracking is simplified to the main program and we do not need to manage them per subprogram. This also means, bpf_prog_free_deferred(), which unwinds the program reference counting and kfrees objects, needs to ensure that we don't try to double free the poke_tab when free'ing the subprog structures. This is easily solved by NULL'ing the poke_tab pointer. The second detail is to ensure that per subprogram JIT logic only does fixups on poke_tab[] entries it owns. To do this, we add a pointer in the poke structure to point at the subprogram value so JITs can easily check while walking the poke_tab structure if the current entry belongs to the current program. The aux pointer is stable and therefore suitable for such comparison. On the jit_subprogs() error path, we omit cleaning up the poke->aux field because these are only ever referenced from the JIT side, but on error we will never make it to the JIT, so its fine to leave them dangling. Removing these pointers would complicate the error path for no reason. However, we do need to untrack all poke descriptors from the main program as otherwise they could race with the freeing of JIT memory from the subprograms. Lastly, a748c6975dea3 ("bpf: propagate poke des ---truncated---

In the Linux kernel, the following vulnerability has been resolved: xen-netback: take a reference to the RX task thread Do this in order to prevent the task from being freed if the thread returns (which can be triggered by the frontend) before the call to kthread_stop done as part of the backend tear down. Not taking the reference will lead to a use-after-free in that scenario. Such reference was taken before but dropped as part of the rework done in 2ac061ce97f4. Reintroduce the reference taking and add a comment this time explaining why it's needed. This is XSA-374 / CVE-2021-28691.

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix potential UAF of struct nilfs_sc_info in nilfs_segctor_thread() The finalization of nilfs_segctor_thread() can race with nilfs_segctor_kill_thread() which terminates that thread, potentially causing a use-after-free BUG as KASAN detected. At the end of nilfs_segctor_thread(), it assigns NULL to "sc_task" member of "struct nilfs_sc_info" to indicate the thread has finished, and then notifies nilfs_segctor_kill_thread() of this using waitqueue "sc_wait_task" on the struct nilfs_sc_info. However, here, immediately after the NULL assignment to "sc_task", it is possible that nilfs_segctor_kill_thread() will detect it and return to continue the deallocation, freeing the nilfs_sc_info structure before the thread does the notification. This fixes the issue by protecting the NULL assignment to "sc_task" and its notification, with spinlock "sc_state_lock" of the struct nilfs_sc_info. Since nilfs_segctor_kill_thread() does a final check to see if "sc_task" is NULL with "sc_state_lock" locked, this can eliminate the race.

In the Linux kernel, the following vulnerability has been resolved: watchdog: Fix possible use-after-free by calling del_timer_sync() This driver's remove path calls del_timer(). However, that function does not wait until the timer handler finishes. This means that the timer handler may still be running after the driver's remove function has finished, which would result in a use-after-free. Fix by calling del_timer_sync(), which makes sure the timer handler has finished, and unable to re-schedule itself.

In the Linux kernel, the following vulnerability has been resolved: regmap: set debugfs_name to NULL after it is freed There is a upstream commit cffa4b2122f5("regmap:debugfs: Fix a memory leak when calling regmap_attach_dev") that adds a if condition when create name for debugfs_name. With below function invoking logical, debugfs_name is freed in regmap_debugfs_exit(), but it is not created again because of the if condition introduced by above commit. regmap_reinit_cache() regmap_debugfs_exit() ... regmap_debugfs_init() So, set debugfs_name to NULL after it is freed.

In the Linux kernel, the following vulnerability has been resolved: net: fix use-after-free in tw_timer_handler A real world panic issue was found as follow in Linux 5.4. BUG: unable to handle page fault for address: ffffde49a863de28 PGD 7e6fe62067 P4D 7e6fe62067 PUD 7e6fe63067 PMD f51e064067 PTE 0 RIP: 0010:tw_timer_handler+0x20/0x40 Call Trace: <IRQ> call_timer_fn+0x2b/0x120 run_timer_softirq+0x1ef/0x450 __do_softirq+0x10d/0x2b8 irq_exit+0xc7/0xd0 smp_apic_timer_interrupt+0x68/0x120 apic_timer_interrupt+0xf/0x20 This issue was also reported since 2017 in the thread [1], unfortunately, the issue was still can be reproduced after fixing DCCP. The ipv4_mib_exit_net is called before tcp_sk_exit_batch when a net namespace is destroyed since tcp_sk_ops is registered befrore ipv4_mib_ops, which means tcp_sk_ops is in the front of ipv4_mib_ops in the list of pernet_list. There will be a use-after-free on net->mib.net_statistics in tw_timer_handler after ipv4_mib_exit_net if there are some inflight time-wait timers. This bug is not introduced by commit f2bf415cfed7 ("mib: add net to NET_ADD_STATS_BH") since the net_statistics is a global variable instead of dynamic allocation and freeing. Actually, commit 61a7e26028b9 ("mib: put net statistics on struct net") introduces the bug since it put net statistics on struct net and free it when net namespace is destroyed. Moving init_ipv4_mibs() to the front of tcp_init() to fix this bug and replace pr_crit() with panic() since continuing is meaningless when init_ipv4_mibs() fails. [1] https://groups.google.com/g/syzkaller/c/p1tn-_Kc6l4/m/smuL_FMAAgAJ?pli=1

In the Linux kernel, the following vulnerability has been resolved: can: vxcan: vxcan_xmit: fix use after free bug After calling netif_rx_ni(skb), dereferencing skb is unsafe. Especially, the canfd_frame cfd which aliases skb memory is accessed after the netif_rx_ni().

In the Linux kernel, the following vulnerability has been resolved: net/nfc: fix use-after-free llcp_sock_bind/connect Commits 8a4cd82d ("nfc: fix refcount leak in llcp_sock_connect()") and c33b1cc62 ("nfc: fix refcount leak in llcp_sock_bind()") fixed a refcount leak bug in bind/connect but introduced a use-after-free if the same local is assigned to 2 different sockets. This can be triggered by the following simple program: int sock1 = socket( AF_NFC, SOCK_STREAM, NFC_SOCKPROTO_LLCP ); int sock2 = socket( AF_NFC, SOCK_STREAM, NFC_SOCKPROTO_LLCP ); memset( &addr, 0, sizeof(struct sockaddr_nfc_llcp) ); addr.sa_family = AF_NFC; addr.nfc_protocol = NFC_PROTO_NFC_DEP; bind( sock1, (struct sockaddr*) &addr, sizeof(struct sockaddr_nfc_llcp) ) bind( sock2, (struct sockaddr*) &addr, sizeof(struct sockaddr_nfc_llcp) ) close(sock1); close(sock2); Fix this by assigning NULL to llcp_sock->local after calling nfc_llcp_local_put. This addresses CVE-2021-23134.

In the Linux kernel, the following vulnerability has been resolved: net: sched: flower: protect fl_walk() with rcu Patch that refactored fl_walk() to use idr_for_each_entry_continue_ul() also removed rcu protection of individual filters which causes following use-after-free when filter is deleted concurrently. Fix fl_walk() to obtain rcu read lock while iterating and taking the filter reference and temporary release the lock while calling arg->fn() callback that can sleep. KASAN trace: [ 352.773640] ================================================================== [ 352.775041] BUG: KASAN: use-after-free in fl_walk+0x159/0x240 [cls_flower] [ 352.776304] Read of size 4 at addr ffff8881c8251480 by task tc/2987 [ 352.777862] CPU: 3 PID: 2987 Comm: tc Not tainted 5.15.0-rc2+ #2 [ 352.778980] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 [ 352.781022] Call Trace: [ 352.781573] dump_stack_lvl+0x46/0x5a [ 352.782332] print_address_description.constprop.0+0x1f/0x140 [ 352.783400] ? fl_walk+0x159/0x240 [cls_flower] [ 352.784292] ? fl_walk+0x159/0x240 [cls_flower] [ 352.785138] kasan_report.cold+0x83/0xdf [ 352.785851] ? fl_walk+0x159/0x240 [cls_flower] [ 352.786587] kasan_check_range+0x145/0x1a0 [ 352.787337] fl_walk+0x159/0x240 [cls_flower] [ 352.788163] ? fl_put+0x10/0x10 [cls_flower] [ 352.789007] ? __mutex_unlock_slowpath.constprop.0+0x220/0x220 [ 352.790102] tcf_chain_dump+0x231/0x450 [ 352.790878] ? tcf_chain_tp_delete_empty+0x170/0x170 [ 352.791833] ? __might_sleep+0x2e/0xc0 [ 352.792594] ? tfilter_notify+0x170/0x170 [ 352.793400] ? __mutex_unlock_slowpath.constprop.0+0x220/0x220 [ 352.794477] tc_dump_tfilter+0x385/0x4b0 [ 352.795262] ? tc_new_tfilter+0x1180/0x1180 [ 352.796103] ? __mod_node_page_state+0x1f/0xc0 [ 352.796974] ? __build_skb_around+0x10e/0x130 [ 352.797826] netlink_dump+0x2c0/0x560 [ 352.798563] ? netlink_getsockopt+0x430/0x430 [ 352.799433] ? __mutex_unlock_slowpath.constprop.0+0x220/0x220 [ 352.800542] __netlink_dump_start+0x356/0x440 [ 352.801397] rtnetlink_rcv_msg+0x3ff/0x550 [ 352.802190] ? tc_new_tfilter+0x1180/0x1180 [ 352.802872] ? rtnl_calcit.isra.0+0x1f0/0x1f0 [ 352.803668] ? tc_new_tfilter+0x1180/0x1180 [ 352.804344] ? _copy_from_iter_nocache+0x800/0x800 [ 352.805202] ? kasan_set_track+0x1c/0x30 [ 352.805900] netlink_rcv_skb+0xc6/0x1f0 [ 352.806587] ? rht_deferred_worker+0x6b0/0x6b0 [ 352.807455] ? rtnl_calcit.isra.0+0x1f0/0x1f0 [ 352.808324] ? netlink_ack+0x4d0/0x4d0 [ 352.809086] ? netlink_deliver_tap+0x62/0x3d0 [ 352.809951] netlink_unicast+0x353/0x480 [ 352.810744] ? netlink_attachskb+0x430/0x430 [ 352.811586] ? __alloc_skb+0xd7/0x200 [ 352.812349] netlink_sendmsg+0x396/0x680 [ 352.813132] ? netlink_unicast+0x480/0x480 [ 352.813952] ? __import_iovec+0x192/0x210 [ 352.814759] ? netlink_unicast+0x480/0x480 [ 352.815580] sock_sendmsg+0x6c/0x80 [ 352.816299] ____sys_sendmsg+0x3a5/0x3c0 [ 352.817096] ? kernel_sendmsg+0x30/0x30 [ 352.817873] ? __ia32_sys_recvmmsg+0x150/0x150 [ 352.818753] ___sys_sendmsg+0xd8/0x140 [ 352.819518] ? sendmsg_copy_msghdr+0x110/0x110 [ 352.820402] ? ___sys_recvmsg+0xf4/0x1a0 [ 352.821110] ? __copy_msghdr_from_user+0x260/0x260 [ 352.821934] ? _raw_spin_lock+0x81/0xd0 [ 352.822680] ? __handle_mm_fault+0xef3/0x1b20 [ 352.823549] ? rb_insert_color+0x2a/0x270 [ 352.824373] ? copy_page_range+0x16b0/0x16b0 [ 352.825209] ? perf_event_update_userpage+0x2d0/0x2d0 [ 352.826190] ? __fget_light+0xd9/0xf0 [ 352.826941] __sys_sendmsg+0xb3/0x130 [ 352.827613] ? __sys_sendmsg_sock+0x20/0x20 [ 352.828377] ? do_user_addr_fault+0x2c5/0x8a0 [ 352.829184] ? fpregs_assert_state_consistent+0x52/0x60 [ 352.830001] ? exit_to_user_mode_prepare+0x32/0x160 [ 352.830845] do_syscall_64+0x35/0x80 [ 352.831445] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 352.832331] RIP: 0033:0x7f7bee973c17 [ ---truncated---

In the Linux kernel, the following vulnerability has been resolved: RDMA: Fix use-after-free in rxe_queue_cleanup On error handling path in rxe_qp_from_init() qp->sq.queue is freed and then rxe_create_qp() will drop last reference to this object. qp clean up function will try to free this queue one time and it causes UAF bug. Fix it by zeroing queue pointer after freeing queue in rxe_qp_from_init().

In the Linux kernel, the following vulnerability has been resolved: ext4: fix possible UAF when remounting r/o a mmp-protected file system After commit 618f003199c6 ("ext4: fix memory leak in ext4_fill_super"), after the file system is remounted read-only, there is a race where the kmmpd thread can exit, causing sbi->s_mmp_tsk to point at freed memory, which the call to ext4_stop_mmpd() can trip over. Fix this by only allowing kmmpd() to exit when it is stopped via ext4_stop_mmpd(). Bug-Report-Link: <20210629143603.2166962-1-yebin10@huawei.com>

In the Linux kernel, the following vulnerability has been resolved: scsi: iscsi: Fix iscsi_task use after free Commit d39df158518c ("scsi: iscsi: Have abort handler get ref to conn") added iscsi_get_conn()/iscsi_put_conn() calls during abort handling but then also changed the handling of the case where we detect an already completed task where we now end up doing a goto to the common put/cleanup code. This results in a iscsi_task use after free, because the common cleanup code will do a put on the iscsi_task. This reverts the goto and moves the iscsi_get_conn() to after we've checked if the iscsi_task is valid.

In the Linux kernel, the following vulnerability has been resolved: bus: mhi: core: Fix invalid error returning in mhi_queue mhi_queue returns an error when the doorbell is not accessible in the current state. This can happen when the device is in non M0 state, like M3, and needs to be waken-up prior ringing the DB. This case is managed earlier by triggering an asynchronous M3 exit via controller resume/suspend callbacks, that in turn will cause M0 transition and DB update. So, since it's not an error but just delaying of doorbell update, there is no reason to return an error. This also fixes a use after free error for skb case, indeed a caller queuing skb will try to free the skb if the queueing fails, but in that case queueing has been done.

In the Linux kernel, the following vulnerability has been resolved: bus: mhi: pci_generic: Fix possible use-after-free in mhi_pci_remove() This driver's remove path calls del_timer(). However, that function does not wait until the timer handler finishes. This means that the timer handler may still be running after the driver's remove function has finished, which would result in a use-after-free. Fix by calling del_timer_sync(), which makes sure the timer handler has finished, and unable to re-schedule itself.

In the Linux kernel, the following vulnerability has been resolved: xfrm: fix slab-use-after-free in decode_session6 When the xfrm device is set to the qdisc of the sfb type, the cb field of the sent skb may be modified during enqueuing. Then, slab-use-after-free may occur when the xfrm device sends IPv6 packets. The stack information is as follows: BUG: KASAN: slab-use-after-free in decode_session6+0x103f/0x1890 Read of size 1 at addr ffff8881111458ef by task swapper/3/0 CPU: 3 PID: 0 Comm: swapper/3 Not tainted 6.4.0-next-20230707 #409 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33 04/01/2014 Call Trace: <IRQ> dump_stack_lvl+0xd9/0x150 print_address_description.constprop.0+0x2c/0x3c0 kasan_report+0x11d/0x130 decode_session6+0x103f/0x1890 __xfrm_decode_session+0x54/0xb0 xfrmi_xmit+0x173/0x1ca0 dev_hard_start_xmit+0x187/0x700 sch_direct_xmit+0x1a3/0xc30 __qdisc_run+0x510/0x17a0 __dev_queue_xmit+0x2215/0x3b10 neigh_connected_output+0x3c2/0x550 ip6_finish_output2+0x55a/0x1550 ip6_finish_output+0x6b9/0x1270 ip6_output+0x1f1/0x540 ndisc_send_skb+0xa63/0x1890 ndisc_send_rs+0x132/0x6f0 addrconf_rs_timer+0x3f1/0x870 call_timer_fn+0x1a0/0x580 expire_timers+0x29b/0x4b0 run_timer_softirq+0x326/0x910 __do_softirq+0x1d4/0x905 irq_exit_rcu+0xb7/0x120 sysvec_apic_timer_interrupt+0x97/0xc0 </IRQ> <TASK> asm_sysvec_apic_timer_interrupt+0x1a/0x20 RIP: 0010:intel_idle_hlt+0x23/0x30 Code: 1f 84 00 00 00 00 00 f3 0f 1e fa 41 54 41 89 d4 0f 1f 44 00 00 66 90 0f 1f 44 00 00 0f 00 2d c4 9f ab 00 0f 1f 44 00 00 fb f4 <fa> 44 89 e0 41 5c c3 66 0f 1f 44 00 00 f3 0f 1e fa 41 54 41 89 d4 RSP: 0018:ffffc90000197d78 EFLAGS: 00000246 RAX: 00000000000a83c3 RBX: ffffe8ffffd09c50 RCX: ffffffff8a22d8e5 RDX: 0000000000000001 RSI: ffffffff8d3f8080 RDI: ffffe8ffffd09c50 RBP: ffffffff8d3f8080 R08: 0000000000000001 R09: ffffed1026ba6d9d R10: ffff888135d36ceb R11: 0000000000000001 R12: 0000000000000001 R13: ffffffff8d3f8100 R14: 0000000000000001 R15: 0000000000000000 cpuidle_enter_state+0xd3/0x6f0 cpuidle_enter+0x4e/0xa0 do_idle+0x2fe/0x3c0 cpu_startup_entry+0x18/0x20 start_secondary+0x200/0x290 secondary_startup_64_no_verify+0x167/0x16b </TASK> Allocated by task 939: kasan_save_stack+0x22/0x40 kasan_set_track+0x25/0x30 __kasan_slab_alloc+0x7f/0x90 kmem_cache_alloc_node+0x1cd/0x410 kmalloc_reserve+0x165/0x270 __alloc_skb+0x129/0x330 inet6_ifa_notify+0x118/0x230 __ipv6_ifa_notify+0x177/0xbe0 addrconf_dad_completed+0x133/0xe00 addrconf_dad_work+0x764/0x1390 process_one_work+0xa32/0x16f0 worker_thread+0x67d/0x10c0 kthread+0x344/0x440 ret_from_fork+0x1f/0x30 The buggy address belongs to the object at ffff888111145800 which belongs to the cache skbuff_small_head of size 640 The buggy address is located 239 bytes inside of freed 640-byte region [ffff888111145800, ffff888111145a80) As commit f855691975bb ("xfrm6: Fix the nexthdr offset in _decode_session6.") showed, xfrm_decode_session was originally intended only for the receive path. IP6CB(skb)->nhoff is not set during transmission. Therefore, set the cb field in the skb to 0 before sending packets.

In the Linux kernel, the following vulnerability has been resolved: gfs2: Fix use-after-free in gfs2_glock_shrink_scan The GLF_LRU flag is checked under lru_lock in gfs2_glock_remove_from_lru() to remove the glock from the lru list in __gfs2_glock_put(). On the shrink scan path, the same flag is cleared under lru_lock but because of cond_resched_lock(&lru_lock) in gfs2_dispose_glock_lru(), progress on the put side can be made without deleting the glock from the lru list. Keep GLF_LRU across the race window opened by cond_resched_lock(&lru_lock) to ensure correct behavior on both sides - clear GLF_LRU after list_del under lru_lock.

In the Linux kernel, the following vulnerability has been resolved: net: qcom/emac: fix UAF in emac_remove adpt is netdev private data and it cannot be used after free_netdev() call. Using adpt after free_netdev() can cause UAF bug. Fix it by moving free_netdev() at the end of the function.

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_tables: unlink table before deleting it syzbot reports following UAF: BUG: KASAN: use-after-free in memcmp+0x18f/0x1c0 lib/string.c:955 nla_strcmp+0xf2/0x130 lib/nlattr.c:836 nft_table_lookup.part.0+0x1a2/0x460 net/netfilter/nf_tables_api.c:570 nft_table_lookup net/netfilter/nf_tables_api.c:4064 [inline] nf_tables_getset+0x1b3/0x860 net/netfilter/nf_tables_api.c:4064 nfnetlink_rcv_msg+0x659/0x13f0 net/netfilter/nfnetlink.c:285 netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2504 Problem is that all get operations are lockless, so the commit_mutex held by nft_rcv_nl_event() isn't enough to stop a parallel GET request from doing read-accesses to the table object even after synchronize_rcu(). To avoid this, unlink the table first and store the table objects in on-stack scratch space.

In the Linux kernel, the following vulnerability has been resolved: blk-cgroup: fix UAF by grabbing blkcg lock before destroying blkg pd KASAN reports a use-after-free report when doing fuzz test: [693354.104835] ================================================================== [693354.105094] BUG: KASAN: use-after-free in bfq_io_set_weight_legacy+0xd3/0x160 [693354.105336] Read of size 4 at addr ffff888be0a35664 by task sh/1453338 [693354.105607] CPU: 41 PID: 1453338 Comm: sh Kdump: loaded Not tainted 4.18.0-147 [693354.105610] Hardware name: Huawei 2288H V5/BC11SPSCB0, BIOS 0.81 07/02/2018 [693354.105612] Call Trace: [693354.105621] dump_stack+0xf1/0x19b [693354.105626] ? show_regs_print_info+0x5/0x5 [693354.105634] ? printk+0x9c/0xc3 [693354.105638] ? cpumask_weight+0x1f/0x1f [693354.105648] print_address_description+0x70/0x360 [693354.105654] kasan_report+0x1b2/0x330 [693354.105659] ? bfq_io_set_weight_legacy+0xd3/0x160 [693354.105665] ? bfq_io_set_weight_legacy+0xd3/0x160 [693354.105670] bfq_io_set_weight_legacy+0xd3/0x160 [693354.105675] ? bfq_cpd_init+0x20/0x20 [693354.105683] cgroup_file_write+0x3aa/0x510 [693354.105693] ? ___slab_alloc+0x507/0x540 [693354.105698] ? cgroup_file_poll+0x60/0x60 [693354.105702] ? 0xffffffff89600000 [693354.105708] ? usercopy_abort+0x90/0x90 [693354.105716] ? mutex_lock+0xef/0x180 [693354.105726] kernfs_fop_write+0x1ab/0x280 [693354.105732] ? cgroup_file_poll+0x60/0x60 [693354.105738] vfs_write+0xe7/0x230 [693354.105744] ksys_write+0xb0/0x140 [693354.105749] ? __ia32_sys_read+0x50/0x50 [693354.105760] do_syscall_64+0x112/0x370 [693354.105766] ? syscall_return_slowpath+0x260/0x260 [693354.105772] ? do_page_fault+0x9b/0x270 [693354.105779] ? prepare_exit_to_usermode+0xf9/0x1a0 [693354.105784] ? enter_from_user_mode+0x30/0x30 [693354.105793] entry_SYSCALL_64_after_hwframe+0x65/0xca [693354.105875] Allocated by task 1453337: [693354.106001] kasan_kmalloc+0xa0/0xd0 [693354.106006] kmem_cache_alloc_node_trace+0x108/0x220 [693354.106010] bfq_pd_alloc+0x96/0x120 [693354.106015] blkcg_activate_policy+0x1b7/0x2b0 [693354.106020] bfq_create_group_hierarchy+0x1e/0x80 [693354.106026] bfq_init_queue+0x678/0x8c0 [693354.106031] blk_mq_init_sched+0x1f8/0x460 [693354.106037] elevator_switch_mq+0xe1/0x240 [693354.106041] elevator_switch+0x25/0x40 [693354.106045] elv_iosched_store+0x1a1/0x230 [693354.106049] queue_attr_store+0x78/0xb0 [693354.106053] kernfs_fop_write+0x1ab/0x280 [693354.106056] vfs_write+0xe7/0x230 [693354.106060] ksys_write+0xb0/0x140 [693354.106064] do_syscall_64+0x112/0x370 [693354.106069] entry_SYSCALL_64_after_hwframe+0x65/0xca [693354.106114] Freed by task 1453336: [693354.106225] __kasan_slab_free+0x130/0x180 [693354.106229] kfree+0x90/0x1b0 [693354.106233] blkcg_deactivate_policy+0x12c/0x220 [693354.106238] bfq_exit_queue+0xf5/0x110 [693354.106241] blk_mq_exit_sched+0x104/0x130 [693354.106245] __elevator_exit+0x45/0x60 [693354.106249] elevator_switch_mq+0xd6/0x240 [693354.106253] elevator_switch+0x25/0x40 [693354.106257] elv_iosched_store+0x1a1/0x230 [693354.106261] queue_attr_store+0x78/0xb0 [693354.106264] kernfs_fop_write+0x1ab/0x280 [693354.106268] vfs_write+0xe7/0x230 [693354.106271] ksys_write+0xb0/0x140 [693354.106275] do_syscall_64+0x112/0x370 [693354.106280] entry_SYSCALL_64_after_hwframe+0x65/0xca [693354.106329] The buggy address belongs to the object at ffff888be0a35580 which belongs to the cache kmalloc-1k of size 1024 [693354.106736] The buggy address is located 228 bytes inside of 1024-byte region [ffff888be0a35580, ffff888be0a35980) [693354.107114] The buggy address belongs to the page: [693354.107273] page:ffffea002f828c00 count:1 mapcount:0 mapping:ffff888107c17080 index:0x0 compound_mapcount: 0 [693354.107606] flags: 0x17ffffc0008100(slab|head) [693354.107760] raw: 0017ffffc0008100 ffffea002fcbc808 ffffea0030bd3a08 ffff888107c17080 [693354.108020] r ---truncated---

In the Linux kernel, the following vulnerability has been resolved: i2c: virtio: disable timeout handling If a timeout is hit, it can result is incorrect data on the I2C bus and/or memory corruptions in the guest since the device can still be operating on the buffers it was given while the guest has freed them. Here is, for example, the start of a slub_debug splat which was triggered on the next transfer after one transfer was forced to timeout by setting a breakpoint in the backend (rust-vmm/vhost-device): BUG kmalloc-1k (Not tainted): Poison overwritten First byte 0x1 instead of 0x6b Allocated in virtio_i2c_xfer+0x65/0x35c age=350 cpu=0 pid=29 __kmalloc+0xc2/0x1c9 virtio_i2c_xfer+0x65/0x35c __i2c_transfer+0x429/0x57d i2c_transfer+0x115/0x134 i2cdev_ioctl_rdwr+0x16a/0x1de i2cdev_ioctl+0x247/0x2ed vfs_ioctl+0x21/0x30 sys_ioctl+0xb18/0xb41 Freed in virtio_i2c_xfer+0x32e/0x35c age=244 cpu=0 pid=29 kfree+0x1bd/0x1cc virtio_i2c_xfer+0x32e/0x35c __i2c_transfer+0x429/0x57d i2c_transfer+0x115/0x134 i2cdev_ioctl_rdwr+0x16a/0x1de i2cdev_ioctl+0x247/0x2ed vfs_ioctl+0x21/0x30 sys_ioctl+0xb18/0xb41 There is no simple fix for this (the driver would have to always create bounce buffers and hold on to them until the device eventually returns the buffers), so just disable the timeout support for now.

In the Linux kernel, the following vulnerability has been resolved: media: davinci: vpif: fix use-after-free on driver unbind The driver allocates and registers two platform device structures during probe, but the devices were never deregistered on driver unbind. This results in a use-after-free on driver unbind as the device structures were allocated using devres and would be freed by driver core when remove() returns. Fix this by adding the missing deregistration calls to the remove() callback and failing probe on registration errors. Note that the platform device structures must be freed using a proper release callback to avoid leaking associated resources like device names.

In the Linux kernel, the following vulnerability has been resolved: misc/libmasm/module: Fix two use after free in ibmasm_init_one In ibmasm_init_one, it calls ibmasm_init_remote_input_dev(). Inside ibmasm_init_remote_input_dev, mouse_dev and keybd_dev are allocated by input_allocate_device(), and assigned to sp->remote.mouse_dev and sp->remote.keybd_dev respectively. In the err_free_devices error branch of ibmasm_init_one, mouse_dev and keybd_dev are freed by input_free_device(), and return error. Then the execution runs into error_send_message error branch of ibmasm_init_one, where ibmasm_free_remote_input_dev(sp) is called to unregister the freed sp->remote.mouse_dev and sp->remote.keybd_dev. My patch add a "error_init_remote" label to handle the error of ibmasm_init_remote_input_dev(), to avoid the uaf bugs.

In the Linux kernel, the following vulnerability has been resolved: RDMA/irdma: Fix a user-after-free in add_pble_prm When irdma_hmc_sd_one fails, 'chunk' is freed while its still on the PBLE info list. Add the chunk entry to the PBLE info list only after successful setting of the SD in irdma_hmc_sd_one.

In the Linux kernel, the following vulnerability has been resolved: habanalabs/gaudi: Fix a potential use after free in gaudi_memset_device_memory Our code analyzer reported a uaf. In gaudi_memset_device_memory, cb is get via hl_cb_kernel_create() with 2 refcount. If hl_cs_allocate_job() failed, the execution runs into release_cb branch. One ref of cb is dropped by hl_cb_put(cb) and could be freed if other thread also drops one ref. Then cb is used by cb->id later, which is a potential uaf. My patch add a variable 'id' to accept the value of cb->id before the hl_cb_put(cb) is called, to avoid the potential uaf.

In the Linux kernel, the following vulnerability has been resolved: atm: nicstar: Fix possible use-after-free in nicstar_cleanup() This module's remove path calls del_timer(). However, that function does not wait until the timer handler finishes. This means that the timer handler may still be running after the driver's remove function has finished, which would result in a use-after-free. Fix by calling del_timer_sync(), which makes sure the timer handler has finished, and unable to re-schedule itself.

In the Linux kernel, the following vulnerability has been resolved: net: macb: fix use after free on rmmod plat_dev->dev->platform_data is released by platform_device_unregister(), use of pclk and hclk is a use-after-free. Since device unregister won't need a clk device we adjust the function call sequence to fix this issue. [ 31.261225] BUG: KASAN: use-after-free in macb_remove+0x77/0xc6 [macb_pci] [ 31.275563] Freed by task 306: [ 30.276782] platform_device_release+0x25/0x80

In the Linux kernel, the following vulnerability has been resolved: iio: mma8452: Fix trigger reference couting The mma8452 driver directly assigns a trigger to the struct iio_dev. The IIO core when done using this trigger will call `iio_trigger_put()` to drop the reference count by 1. Without the matching `iio_trigger_get()` in the driver the reference count can reach 0 too early, the trigger gets freed while still in use and a use-after-free occurs. Fix this by getting a reference to the trigger before assigning it to the IIO device.

In the Linux kernel, the following vulnerability has been resolved: net: usb: fix possible use-after-free in smsc75xx_bind The commit 46a8b29c6306 ("net: usb: fix memory leak in smsc75xx_bind") fails to clean up the work scheduled in smsc75xx_reset-> smsc75xx_set_multicast, which leads to use-after-free if the work is scheduled to start after the deallocation. In addition, this patch also removes a dangling pointer - dev->data[0]. This patch calls cancel_work_sync to cancel the scheduled work and set the dangling pointer to NULL.

In the Linux kernel, the following vulnerability has been resolved: scsi: iscsi: Fix conn use after free during resets If we haven't done a unbind target call we can race where iscsi_conn_teardown wakes up the EH thread and then frees the conn while those threads are still accessing the conn ehwait. We can only do one TMF per session so this just moves the TMF fields from the conn to the session. We can then rely on the iscsi_session_teardown->iscsi_remove_session->__iscsi_unbind_session call to remove the target and it's devices, and know after that point there is no device or scsi-ml callout trying to access the session.

In the Linux kernel, the following vulnerability has been resolved: sata_fsl: fix UAF in sata_fsl_port_stop when rmmod sata_fsl When the `rmmod sata_fsl.ko` command is executed in the PPC64 GNU/Linux, a bug is reported: ================================================================== BUG: Unable to handle kernel data access on read at 0x80000800805b502c Oops: Kernel access of bad area, sig: 11 [#1] NIP [c0000000000388a4] .ioread32+0x4/0x20 LR [80000000000c6034] .sata_fsl_port_stop+0x44/0xe0 [sata_fsl] Call Trace: .free_irq+0x1c/0x4e0 (unreliable) .ata_host_stop+0x74/0xd0 [libata] .release_nodes+0x330/0x3f0 .device_release_driver_internal+0x178/0x2c0 .driver_detach+0x64/0xd0 .bus_remove_driver+0x70/0xf0 .driver_unregister+0x38/0x80 .platform_driver_unregister+0x14/0x30 .fsl_sata_driver_exit+0x18/0xa20 [sata_fsl] .__se_sys_delete_module+0x1ec/0x2d0 .system_call_exception+0xfc/0x1f0 system_call_common+0xf8/0x200 ================================================================== The triggering of the BUG is shown in the following stack: driver_detach device_release_driver_internal __device_release_driver drv->remove(dev) --> platform_drv_remove/platform_remove drv->remove(dev) --> sata_fsl_remove iounmap(host_priv->hcr_base); <---- unmap kfree(host_priv); <---- free devres_release_all release_nodes dr->node.release(dev, dr->data) --> ata_host_stop ap->ops->port_stop(ap) --> sata_fsl_port_stop ioread32(hcr_base + HCONTROL) <---- UAF host->ops->host_stop(host) The iounmap(host_priv->hcr_base) and kfree(host_priv) functions should not be executed in drv->remove. These functions should be executed in host_stop after port_stop. Therefore, we move these functions to the new function sata_fsl_host_stop and bind the new function to host_stop.

In the Linux kernel, the following vulnerability has been resolved: aio: fix use-after-free due to missing POLLFREE handling signalfd_poll() and binder_poll() are special in that they use a waitqueue whose lifetime is the current task, rather than the struct file as is normally the case. This is okay for blocking polls, since a blocking poll occurs within one task; however, non-blocking polls require another solution. This solution is for the queue to be cleared before it is freed, by sending a POLLFREE notification to all waiters. Unfortunately, only eventpoll handles POLLFREE. A second type of non-blocking poll, aio poll, was added in kernel v4.18, and it doesn't handle POLLFREE. This allows a use-after-free to occur if a signalfd or binder fd is polled with aio poll, and the waitqueue gets freed. Fix this by making aio poll handle POLLFREE. A patch by Ramji Jiyani <ramjiyani@google.com> (https://lore.kernel.org/r/20211027011834.2497484-1-ramjiyani@google.com) tried to do this by making aio_poll_wake() always complete the request inline if POLLFREE is seen. However, that solution had two bugs. First, it introduced a deadlock, as it unconditionally locked the aio context while holding the waitqueue lock, which inverts the normal locking order. Second, it didn't consider that POLLFREE notifications are missed while the request has been temporarily de-queued. The second problem was solved by my previous patch. This patch then properly fixes the use-after-free by handling POLLFREE in a deadlock-free way. It does this by taking advantage of the fact that freeing of the waitqueue is RCU-delayed, similar to what eventpoll does.

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix use-after-free bug in cifs_debug_data_proc_show() Skip SMB sessions that are being teared down (e.g. @ses->ses_status == SES_EXITING) in cifs_debug_data_proc_show() to avoid use-after-free in @ses. This fixes the following GPF when reading from /proc/fs/cifs/DebugData while mounting and umounting [ 816.251274] general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6d81: 0000 [#1] PREEMPT SMP NOPTI ... [ 816.260138] Call Trace: [ 816.260329] <TASK> [ 816.260499] ? die_addr+0x36/0x90 [ 816.260762] ? exc_general_protection+0x1b3/0x410 [ 816.261126] ? asm_exc_general_protection+0x26/0x30 [ 816.261502] ? cifs_debug_tcon+0xbd/0x240 [cifs] [ 816.261878] ? cifs_debug_tcon+0xab/0x240 [cifs] [ 816.262249] cifs_debug_data_proc_show+0x516/0xdb0 [cifs] [ 816.262689] ? seq_read_iter+0x379/0x470 [ 816.262995] seq_read_iter+0x118/0x470 [ 816.263291] proc_reg_read_iter+0x53/0x90 [ 816.263596] ? srso_alias_return_thunk+0x5/0x7f [ 816.263945] vfs_read+0x201/0x350 [ 816.264211] ksys_read+0x75/0x100 [ 816.264472] do_syscall_64+0x3f/0x90 [ 816.264750] entry_SYSCALL_64_after_hwframe+0x6e/0xd8 [ 816.265135] RIP: 0033:0x7fd5e669d381

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix out of bounds in init_smb2_rsp_hdr() If client send smb2 negotiate request and then send smb1 negotiate request, init_smb2_rsp_hdr is called for smb1 negotiate request since need_neg is set to false. This patch ignore smb1 packets after ->need_neg is set to false.

In the Linux kernel, the following vulnerability has been resolved: net: bridge: fix vlan tunnel dst refcnt when egressing The egress tunnel code uses dst_clone() and directly sets the result which is wrong because the entry might have 0 refcnt or be already deleted, causing number of problems. It also triggers the WARN_ON() in dst_hold()[1] when a refcnt couldn't be taken. Fix it by using dst_hold_safe() and checking if a reference was actually taken before setting the dst. [1] dmesg WARN_ON log and following refcnt errors WARNING: CPU: 5 PID: 38 at include/net/dst.h:230 br_handle_egress_vlan_tunnel+0x10b/0x134 [bridge] Modules linked in: 8021q garp mrp bridge stp llc bonding ipv6 virtio_net CPU: 5 PID: 38 Comm: ksoftirqd/5 Kdump: loaded Tainted: G W 5.13.0-rc3+ #360 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33 04/01/2014 RIP: 0010:br_handle_egress_vlan_tunnel+0x10b/0x134 [bridge] Code: e8 85 bc 01 e1 45 84 f6 74 90 45 31 f6 85 db 48 c7 c7 a0 02 19 a0 41 0f 94 c6 31 c9 31 d2 44 89 f6 e8 64 bc 01 e1 85 db 75 02 <0f> 0b 31 c9 31 d2 44 89 f6 48 c7 c7 70 02 19 a0 e8 4b bc 01 e1 49 RSP: 0018:ffff8881003d39e8 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffffffffa01902a0 RBP: ffff8881040c6700 R08: 0000000000000000 R09: 0000000000000001 R10: 2ce93d0054fe0d00 R11: 54fe0d00000e0000 R12: ffff888109515000 R13: 0000000000000000 R14: 0000000000000001 R15: 0000000000000401 FS: 0000000000000000(0000) GS:ffff88822bf40000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f42ba70f030 CR3: 0000000109926000 CR4: 00000000000006e0 Call Trace: br_handle_vlan+0xbc/0xca [bridge] __br_forward+0x23/0x164 [bridge] deliver_clone+0x41/0x48 [bridge] br_handle_frame_finish+0x36f/0x3aa [bridge] ? skb_dst+0x2e/0x38 [bridge] ? br_handle_ingress_vlan_tunnel+0x3e/0x1c8 [bridge] ? br_handle_frame_finish+0x3aa/0x3aa [bridge] br_handle_frame+0x2c3/0x377 [bridge] ? __skb_pull+0x33/0x51 ? vlan_do_receive+0x4f/0x36a ? br_handle_frame_finish+0x3aa/0x3aa [bridge] __netif_receive_skb_core+0x539/0x7c6 ? __list_del_entry_valid+0x16e/0x1c2 __netif_receive_skb_list_core+0x6d/0xd6 netif_receive_skb_list_internal+0x1d9/0x1fa gro_normal_list+0x22/0x3e dev_gro_receive+0x55b/0x600 ? detach_buf_split+0x58/0x140 napi_gro_receive+0x94/0x12e virtnet_poll+0x15d/0x315 [virtio_net] __napi_poll+0x2c/0x1c9 net_rx_action+0xe6/0x1fb __do_softirq+0x115/0x2d8 run_ksoftirqd+0x18/0x20 smpboot_thread_fn+0x183/0x19c ? smpboot_unregister_percpu_thread+0x66/0x66 kthread+0x10a/0x10f ? kthread_mod_delayed_work+0xb6/0xb6 ret_from_fork+0x22/0x30 ---[ end trace 49f61b07f775fd2b ]--- dst_release: dst:00000000c02d677a refcnt:-1 dst_release underflow

In the Linux kernel, the following vulnerability has been resolved: EDAC/qcom: Do not pass llcc_driv_data as edac_device_ctl_info's pvt_info The memory for llcc_driv_data is allocated by the LLCC driver. But when it is passed as the private driver info to the EDAC core, it will get freed during the qcom_edac driver release. So when the qcom_edac driver gets probed again, it will try to use the freed data leading to the use-after-free bug. Hence, do not pass llcc_driv_data as pvt_info but rather reference it using the platform_data pointer in the qcom_edac driver.

A vulnerability classified as critical was found in code-projects Simple Movie Ticket Booking System 1.0. Affected by this vulnerability is the function changeprize. The manipulation of the argument prize leads to stack-based buffer overflow. The attack needs to be approached locally. The exploit has been disclosed to the public and may be used.

In the Linux kernel, the following vulnerability has been resolved: EDAC/thunderx: Fix possible out-of-bounds string access Enabling -Wstringop-overflow globally exposes a warning for a common bug in the usage of strncat(): drivers/edac/thunderx_edac.c: In function 'thunderx_ocx_com_threaded_isr': drivers/edac/thunderx_edac.c:1136:17: error: 'strncat' specified bound 1024 equals destination size [-Werror=stringop-overflow=] 1136 | strncat(msg, other, OCX_MESSAGE_SIZE); | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ... 1145 | strncat(msg, other, OCX_MESSAGE_SIZE); ... 1150 | strncat(msg, other, OCX_MESSAGE_SIZE); ... Apparently the author of this driver expected strncat() to behave the way that strlcat() does, which uses the size of the destination buffer as its third argument rather than the length of the source buffer. The result is that there is no check on the size of the allocated buffer. Change it to strlcat(). [ bp: Trim compiler output, fixup commit message. ]

In the Linux kernel, the following vulnerability has been resolved: vhost-vdpa: fix use after free in vhost_vdpa_probe() The put_device() calls vhost_vdpa_release_dev() which calls ida_simple_remove() and frees "v". So this call to ida_simple_remove() is a use after free and a double free.

In the Linux kernel, the following vulnerability has been resolved: jfs: fix uaf in jfs_evict_inode When the execution of diMount(ipimap) fails, the object ipimap that has been released may be accessed in diFreeSpecial(). Asynchronous ipimap release occurs when rcu_core() calls jfs_free_node(). Therefore, when diMount(ipimap) fails, sbi->ipimap should not be initialized as ipimap.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to avoid dirent corruption As Al reported in link[1]: f2fs_rename() ... if (old_dir != new_dir && !whiteout) f2fs_set_link(old_inode, old_dir_entry, old_dir_page, new_dir); else f2fs_put_page(old_dir_page, 0); You want correct inumber in the ".." link. And cross-directory rename does move the source to new parent, even if you'd been asked to leave a whiteout in the old place. [1] https://lore.kernel.org/all/20231017055040.GN800259@ZenIV/ With below testcase, it may cause dirent corruption, due to it missed to call f2fs_set_link() to update ".." link to new directory. - mkdir -p dir/foo - renameat2 -w dir/foo bar [ASSERT] (__chk_dots_dentries:1421) --> Bad inode number[0x4] for '..', parent parent ino is [0x3] [FSCK] other corrupted bugs [Fail]