In the Linux kernel, the following vulnerability has been resolved: iavf: Fix adminq error handling iavf_alloc_asq_bufs/iavf_alloc_arq_bufs allocates with dma_alloc_coherent memory for VF mailbox. Free DMA regions for both ASQ and ARQ in case error happens during configuration of ASQ/ARQ registers. Without this change it is possible to see when unloading interface: 74626.583369: dma_debug_device_change: device driver has pending DMA allocations while released from device [count=32] One of leaked entries details: [device address=0x0000000b27ff9000] [size=4096 bytes] [mapped with DMA_BIDIRECTIONAL] [mapped as coherent]

In the Linux kernel, the following vulnerability has been resolved: macvlan: enforce a consistent minimal mtu macvlan should enforce a minimal mtu of 68, even at link creation. This patch avoids the current behavior (which could lead to crashes in ipv6 stack if the link is brought up) $ ip link add macvlan1 link eno1 mtu 8 type macvlan # This should fail ! $ ip link sh dev macvlan1 5: macvlan1@eno1: <BROADCAST,MULTICAST> mtu 8 qdisc noop state DOWN mode DEFAULT group default qlen 1000 link/ether 02:47:6c:24:74:82 brd ff:ff:ff:ff:ff:ff $ ip link set macvlan1 mtu 67 Error: mtu less than device minimum. $ ip link set macvlan1 mtu 68 $ ip link set macvlan1 mtu 8 Error: mtu less than device minimum.

In the Linux kernel, the following vulnerability has been resolved: KVM: x86/xen: Initialize Xen timer only once Add a check for existing xen timers before initializing a new one. Currently kvm_xen_init_timer() is called on every KVM_XEN_VCPU_ATTR_TYPE_TIMER, which is causing the following ODEBUG crash when vcpu->arch.xen.timer is already set. ODEBUG: init active (active state 0) object type: hrtimer hint: xen_timer_callbac0 RIP: 0010:debug_print_object+0x16e/0x250 lib/debugobjects.c:502 Call Trace: __debug_object_init debug_hrtimer_init debug_init hrtimer_init kvm_xen_init_timer kvm_xen_vcpu_set_attr kvm_arch_vcpu_ioctl kvm_vcpu_ioctl vfs_ioctl

In the Linux kernel, the following vulnerability has been resolved: clocksource: hyper-v: unexport __init-annotated hv_init_clocksource() EXPORT_SYMBOL and __init is a bad combination because the .init.text section is freed up after the initialization. Hence, modules cannot use symbols annotated __init. The access to a freed symbol may end up with kernel panic. modpost used to detect it, but it has been broken for a decade. Recently, I fixed modpost so it started to warn it again, then this showed up in linux-next builds. There are two ways to fix it: - Remove __init - Remove EXPORT_SYMBOL I chose the latter for this case because the only in-tree call-site, arch/x86/kernel/cpu/mshyperv.c is never compiled as modular. (CONFIG_HYPERVISOR_GUEST is boolean)

In the Linux kernel, the following vulnerability has been resolved: ACPI: APEI: Fix integer overflow in ghes_estatus_pool_init() Change num_ghes from int to unsigned int, preventing an overflow and causing subsequent vmalloc() to fail. The overflow happens in ghes_estatus_pool_init() when calculating len during execution of the statement below as both multiplication operands here are signed int: len += (num_ghes * GHES_ESOURCE_PREALLOC_MAX_SIZE); The following call trace is observed because of this bug: [ 9.317108] swapper/0: vmalloc error: size 18446744071562596352, exceeds total pages, mode:0xcc0(GFP_KERNEL), nodemask=(null),cpuset=/,mems_allowed=0-1 [ 9.317131] Call Trace: [ 9.317134] <TASK> [ 9.317137] dump_stack_lvl+0x49/0x5f [ 9.317145] dump_stack+0x10/0x12 [ 9.317146] warn_alloc.cold+0x7b/0xdf [ 9.317150] ? __device_attach+0x16a/0x1b0 [ 9.317155] __vmalloc_node_range+0x702/0x740 [ 9.317160] ? device_add+0x17f/0x920 [ 9.317164] ? dev_set_name+0x53/0x70 [ 9.317166] ? platform_device_add+0xf9/0x240 [ 9.317168] __vmalloc_node+0x49/0x50 [ 9.317170] ? ghes_estatus_pool_init+0x43/0xa0 [ 9.317176] vmalloc+0x21/0x30 [ 9.317177] ghes_estatus_pool_init+0x43/0xa0 [ 9.317179] acpi_hest_init+0x129/0x19c [ 9.317185] acpi_init+0x434/0x4a4 [ 9.317188] ? acpi_sleep_proc_init+0x2a/0x2a [ 9.317190] do_one_initcall+0x48/0x200 [ 9.317195] kernel_init_freeable+0x221/0x284 [ 9.317200] ? rest_init+0xe0/0xe0 [ 9.317204] kernel_init+0x1a/0x130 [ 9.317205] ret_from_fork+0x22/0x30 [ 9.317208] </TASK> [ rjw: Subject and changelog edits ]

In the Linux kernel, the following vulnerability has been resolved: ARM: cns3xxx: Fix refcount leak in cns3xxx_init of_find_compatible_node() returns a node pointer with refcount incremented, we should use of_node_put() on it when done. Add missing of_node_put() to avoid refcount leak.

In the Linux kernel, the following vulnerability has been resolved: arm64: ftrace: consistently handle PLTs. Sometimes it is necessary to use a PLT entry to call an ftrace trampoline. This is handled by ftrace_make_call() and ftrace_make_nop(), with each having *almost* identical logic, but this is not handled by ftrace_modify_call() since its introduction in commit: 3b23e4991fb66f6d ("arm64: implement ftrace with regs") Due to this, if we ever were to call ftrace_modify_call() for a callsite which requires a PLT entry for a trampoline, then either: a) If the old addr requires a trampoline, ftrace_modify_call() will use an out-of-range address to generate the 'old' branch instruction. This will result in warnings from aarch64_insn_gen_branch_imm() and ftrace_modify_code(), and no instructions will be modified. As ftrace_modify_call() will return an error, this will result in subsequent internal ftrace errors. b) If the old addr does not require a trampoline, but the new addr does, ftrace_modify_call() will use an out-of-range address to generate the 'new' branch instruction. This will result in warnings from aarch64_insn_gen_branch_imm(), and ftrace_modify_code() will replace the 'old' branch with a BRK. This will result in a kernel panic when this BRK is later executed. Practically speaking, case (a) is vastly more likely than case (b), and typically this will result in internal ftrace errors that don't necessarily affect the rest of the system. This can be demonstrated with an out-of-tree test module which triggers ftrace_modify_call(), e.g. | # insmod test_ftrace.ko | test_ftrace: Function test_function raw=0xffffb3749399201c, callsite=0xffffb37493992024 | branch_imm_common: offset out of range | branch_imm_common: offset out of range | ------------[ ftrace bug ]------------ | ftrace failed to modify | [<ffffb37493992024>] test_function+0x8/0x38 [test_ftrace] | actual: 1d:00:00:94 | Updating ftrace call site to call a different ftrace function | ftrace record flags: e0000002 | (2) R | expected tramp: ffffb374ae42ed54 | ------------[ cut here ]------------ | WARNING: CPU: 0 PID: 165 at kernel/trace/ftrace.c:2085 ftrace_bug+0x280/0x2b0 | Modules linked in: test_ftrace(+) | CPU: 0 PID: 165 Comm: insmod Not tainted 5.19.0-rc2-00002-g4d9ead8b45ce #13 | Hardware name: linux,dummy-virt (DT) | pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) | pc : ftrace_bug+0x280/0x2b0 | lr : ftrace_bug+0x280/0x2b0 | sp : ffff80000839ba00 | x29: ffff80000839ba00 x28: 0000000000000000 x27: ffff80000839bcf0 | x26: ffffb37493994180 x25: ffffb374b0991c28 x24: ffffb374b0d70000 | x23: 00000000ffffffea x22: ffffb374afcc33b0 x21: ffffb374b08f9cc8 | x20: ffff572b8462c000 x19: ffffb374b08f9000 x18: ffffffffffffffff | x17: 6c6c6163202c6331 x16: ffffb374ae5ad110 x15: ffffb374b0d51ee4 | x14: 0000000000000000 x13: 3435646532346561 x12: 3437336266666666 | x11: 203a706d61727420 x10: 6465746365707865 x9 : ffffb374ae5149e8 | x8 : 336266666666203a x7 : 706d617274206465 x6 : 00000000fffff167 | x5 : ffff572bffbc4a08 x4 : 00000000fffff167 x3 : 0000000000000000 | x2 : 0000000000000000 x1 : ffff572b84461e00 x0 : 0000000000000022 | Call trace: | ftrace_bug+0x280/0x2b0 | ftrace_replace_code+0x98/0xa0 | ftrace_modify_all_code+0xe0/0x144 | arch_ftrace_update_code+0x14/0x20 | ftrace_startup+0xf8/0x1b0 | register_ftrace_function+0x38/0x90 | test_ftrace_init+0xd0/0x1000 [test_ftrace] | do_one_initcall+0x50/0x2b0 | do_init_module+0x50/0x1f0 | load_module+0x17c8/0x1d64 | __do_sys_finit_module+0xa8/0x100 | __arm64_sys_finit_module+0x2c/0x3c | invoke_syscall+0x50/0x120 | el0_svc_common.constprop.0+0xdc/0x100 | do_el0_svc+0x3c/0xd0 | el0_svc+0x34/0xb0 | el0t_64_sync_handler+0xbc/0x140 | el0t_64_sync+0x18c/0x190 | ---[ end trace 0000000000000000 ]--- We can solve this by consistently determining whether to use a PLT entry for an address. Note that since (the earlier) commit: f1a54ae9 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: net: stmmac: dwc-qos: Disable split header for Tegra194 There is a long-standing issue with the Synopsys DWC Ethernet driver for Tegra194 where random system crashes have been observed [0]. The problem occurs when the split header feature is enabled in the stmmac driver. In the bad case, a larger than expected buffer length is received and causes the calculation of the total buffer length to overflow. This results in a very large buffer length that causes the kernel to crash. Why this larger buffer length is received is not clear, however, the feedback from the NVIDIA design team is that the split header feature is not supported for Tegra194. Therefore, disable split header support for Tegra194 to prevent these random crashes from occurring. [0] https://lore.kernel.org/linux-tegra/b0b17697-f23e-8fa5-3757-604a86f3a095@nvidia.com/

In the Linux kernel, the following vulnerability has been resolved: pinctrl: renesas: rzn1: Fix possible null-ptr-deref in sh_pfc_map_resources() It will cause null-ptr-deref when using 'res', if platform_get_resource() returns NULL, so move using 'res' after devm_ioremap_resource() that will check it to avoid null-ptr-deref. And use devm_platform_get_and_ioremap_resource() to simplify code.

In the Linux kernel, the following vulnerability has been resolved: drm/msm/adreno: Assign msm_gpu->pdev earlier to avoid nullptrs There are some cases, such as the one uncovered by Commit 46d4efcccc68 ("drm/msm/a6xx: Avoid a nullptr dereference when speedbin setting fails") where msm_gpu_cleanup() : platform_set_drvdata(gpu->pdev, NULL); is called on gpu->pdev == NULL, as the GPU device has not been fully initialized yet. Turns out that there's more than just the aforementioned path that causes this to happen (e.g. the case when there's speedbin data in the catalog, but opp-supported-hw is missing in DT). Assigning msm_gpu->pdev earlier seems like the least painful solution to this, therefore do so. Patchwork: https://patchwork.freedesktop.org/patch/602742/

In the Linux kernel, the following vulnerability has been resolved: mm/gup: fix gup_pud_range() for dax For dax pud, pud_huge() returns true on x86. So the function works as long as hugetlb is configured. However, dax doesn't depend on hugetlb. Commit 414fd080d125 ("mm/gup: fix gup_pmd_range() for dax") fixed devmap-backed huge PMDs, but missed devmap-backed huge PUDs. Fix this as well. This fixes the below kernel panic: general protection fault, probably for non-canonical address 0x69e7c000cc478: 0000 [#1] SMP < snip > Call Trace: <TASK> get_user_pages_fast+0x1f/0x40 iov_iter_get_pages+0xc6/0x3b0 ? mempool_alloc+0x5d/0x170 bio_iov_iter_get_pages+0x82/0x4e0 ? bvec_alloc+0x91/0xc0 ? bio_alloc_bioset+0x19a/0x2a0 blkdev_direct_IO+0x282/0x480 ? __io_complete_rw_common+0xc0/0xc0 ? filemap_range_has_page+0x82/0xc0 generic_file_direct_write+0x9d/0x1a0 ? inode_update_time+0x24/0x30 __generic_file_write_iter+0xbd/0x1e0 blkdev_write_iter+0xb4/0x150 ? io_import_iovec+0x8d/0x340 io_write+0xf9/0x300 io_issue_sqe+0x3c3/0x1d30 ? sysvec_reschedule_ipi+0x6c/0x80 __io_queue_sqe+0x33/0x240 ? fget+0x76/0xa0 io_submit_sqes+0xe6a/0x18d0 ? __fget_light+0xd1/0x100 __x64_sys_io_uring_enter+0x199/0x880 ? __context_tracking_enter+0x1f/0x70 ? irqentry_exit_to_user_mode+0x24/0x30 ? irqentry_exit+0x1d/0x30 ? __context_tracking_exit+0xe/0x70 do_syscall_64+0x3b/0x90 entry_SYSCALL_64_after_hwframe+0x61/0xcb RIP: 0033:0x7fc97c11a7be < snip > </TASK> ---[ end trace 48b2e0e67debcaeb ]--- RIP: 0010:internal_get_user_pages_fast+0x340/0x990 < snip > Kernel panic - not syncing: Fatal exception Kernel Offset: disabled

In the Linux kernel, the following vulnerability has been resolved: ARM: OMAP2+: Fix refcount leak in omapdss_init_of omapdss_find_dss_of_node() calls of_find_compatible_node() to get device node. of_find_compatible_node() returns a node pointer with refcount incremented, we should use of_node_put() on it when done. Add missing of_node_put() in later error path and normal path.

In the Linux kernel, the following vulnerability has been resolved: ice: fix 'scheduling while atomic' on aux critical err interrupt There's a kernel BUG splat on processing aux critical error interrupts in ice_misc_intr(): [ 2100.917085] BUG: scheduling while atomic: swapper/15/0/0x00010000 ... [ 2101.060770] Call Trace: [ 2101.063229] <IRQ> [ 2101.065252] dump_stack+0x41/0x60 [ 2101.068587] __schedule_bug.cold.100+0x4c/0x58 [ 2101.073060] __schedule+0x6a4/0x830 [ 2101.076570] schedule+0x35/0xa0 [ 2101.079727] schedule_preempt_disabled+0xa/0x10 [ 2101.084284] __mutex_lock.isra.7+0x310/0x420 [ 2101.088580] ? ice_misc_intr+0x201/0x2e0 [ice] [ 2101.093078] ice_send_event_to_aux+0x25/0x70 [ice] [ 2101.097921] ice_misc_intr+0x220/0x2e0 [ice] [ 2101.102232] __handle_irq_event_percpu+0x40/0x180 [ 2101.106965] handle_irq_event_percpu+0x30/0x80 [ 2101.111434] handle_irq_event+0x36/0x53 [ 2101.115292] handle_edge_irq+0x82/0x190 [ 2101.119148] handle_irq+0x1c/0x30 [ 2101.122480] do_IRQ+0x49/0xd0 [ 2101.125465] common_interrupt+0xf/0xf [ 2101.129146] </IRQ> ... As Andrew correctly mentioned previously[0], the following call ladder happens: ice_misc_intr() <- hardirq ice_send_event_to_aux() device_lock() mutex_lock() might_sleep() might_resched() <- oops Add a new PF state bit which indicates that an aux critical error occurred and serve it in ice_service_task() in process context. The new ice_pf::oicr_err_reg is read-write in both hardirq and process contexts, but only 3 bits of non-critical data probably aren't worth explicit synchronizing (and they're even in the same byte [31:24]). [0] https://lore.kernel.org/all/YeSRUVmrdmlUXHDn@lunn.ch

In the Linux kernel, the following vulnerability has been resolved: meson-mx-socinfo: Fix refcount leak in meson_mx_socinfo_init of_find_matching_node() returns a node pointer with refcount incremented, we should use of_node_put() on it when not need anymore. Add missing of_node_put() to avoid refcount leak.

In the Linux kernel, the following vulnerability has been resolved: media: lgdt3306a: Add a check against null-pointer-def The driver should check whether the client provides the platform_data. The following log reveals it: [ 29.610324] BUG: KASAN: null-ptr-deref in kmemdup+0x30/0x40 [ 29.610730] Read of size 40 at addr 0000000000000000 by task bash/414 [ 29.612820] Call Trace: [ 29.613030] <TASK> [ 29.613201] dump_stack_lvl+0x56/0x6f [ 29.613496] ? kmemdup+0x30/0x40 [ 29.613754] print_report.cold+0x494/0x6b7 [ 29.614082] ? kmemdup+0x30/0x40 [ 29.614340] kasan_report+0x8a/0x190 [ 29.614628] ? kmemdup+0x30/0x40 [ 29.614888] kasan_check_range+0x14d/0x1d0 [ 29.615213] memcpy+0x20/0x60 [ 29.615454] kmemdup+0x30/0x40 [ 29.615700] lgdt3306a_probe+0x52/0x310 [ 29.616339] i2c_device_probe+0x951/0xa90

In the Linux kernel, the following vulnerability has been resolved: staging: fbtft: core: set smem_len before fb_deferred_io_init call The fbtft_framebuffer_alloc() calls fb_deferred_io_init() before initializing info->fix.smem_len. It is set to zero by the framebuffer_alloc() function. It will trigger a WARN_ON() at the start of fb_deferred_io_init() and the function will not do anything.

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix deadlock between concurrent dio writes when low on free data space When reserving data space for a direct IO write we can end up deadlocking if we have multiple tasks attempting a write to the same file range, there are multiple extents covered by that file range, we are low on available space for data and the writes don't expand the inode's i_size. The deadlock can happen like this: 1) We have a file with an i_size of 1M, at offset 0 it has an extent with a size of 128K and at offset 128K it has another extent also with a size of 128K; 2) Task A does a direct IO write against file range [0, 256K), and because the write is within the i_size boundary, it takes the inode's lock (VFS level) in shared mode; 3) Task A locks the file range [0, 256K) at btrfs_dio_iomap_begin(), and then gets the extent map for the extent covering the range [0, 128K). At btrfs_get_blocks_direct_write(), it creates an ordered extent for that file range ([0, 128K)); 4) Before returning from btrfs_dio_iomap_begin(), it unlocks the file range [0, 256K); 5) Task A executes btrfs_dio_iomap_begin() again, this time for the file range [128K, 256K), and locks the file range [128K, 256K); 6) Task B starts a direct IO write against file range [0, 256K) as well. It also locks the inode in shared mode, as it's within the i_size limit, and then tries to lock file range [0, 256K). It is able to lock the subrange [0, 128K) but then blocks waiting for the range [128K, 256K), as it is currently locked by task A; 7) Task A enters btrfs_get_blocks_direct_write() and tries to reserve data space. Because we are low on available free space, it triggers the async data reclaim task, and waits for it to reserve data space; 8) The async reclaim task decides to wait for all existing ordered extents to complete (through btrfs_wait_ordered_roots()). It finds the ordered extent previously created by task A for the file range [0, 128K) and waits for it to complete; 9) The ordered extent for the file range [0, 128K) can not complete because it blocks at btrfs_finish_ordered_io() when trying to lock the file range [0, 128K). This results in a deadlock, because: - task B is holding the file range [0, 128K) locked, waiting for the range [128K, 256K) to be unlocked by task A; - task A is holding the file range [128K, 256K) locked and it's waiting for the async data reclaim task to satisfy its space reservation request; - the async data reclaim task is waiting for ordered extent [0, 128K) to complete, but the ordered extent can not complete because the file range [0, 128K) is currently locked by task B, which is waiting on task A to unlock file range [128K, 256K) and task A waiting on the async data reclaim task. This results in a deadlock between 4 task: task A, task B, the async data reclaim task and the task doing ordered extent completion (a work queue task). This type of deadlock can sporadically be triggered by the test case generic/300 from fstests, and results in a stack trace like the following: [12084.033689] INFO: task kworker/u16:7:123749 blocked for more than 241 seconds. [12084.034877] Not tainted 5.18.0-rc2-btrfs-next-115 #1 [12084.035562] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [12084.036548] task:kworker/u16:7 state:D stack: 0 pid:123749 ppid: 2 flags:0x00004000 [12084.036554] Workqueue: btrfs-flush_delalloc btrfs_work_helper [btrfs] [12084.036599] Call Trace: [12084.036601] <TASK> [12084.036606] __schedule+0x3cb/0xed0 [12084.036616] schedule+0x4e/0xb0 [12084.036620] btrfs_start_ordered_extent+0x109/0x1c0 [btrfs] [12084.036651] ? prepare_to_wait_exclusive+0xc0/0xc0 [12084.036659] btrfs_run_ordered_extent_work+0x1a/0x30 [btrfs] [12084.036688] btrfs_work_helper+0xf8/0x400 [btrfs] [12084.0367 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: ocfs2: fix DIO failure due to insufficient transaction credits The code in ocfs2_dio_end_io_write() estimates number of necessary transaction credits using ocfs2_calc_extend_credits(). This however does not take into account that the IO could be arbitrarily large and can contain arbitrary number of extents. Extent tree manipulations do often extend the current transaction but not in all of the cases. For example if we have only single block extents in the tree, ocfs2_mark_extent_written() will end up calling ocfs2_replace_extent_rec() all the time and we will never extend the current transaction and eventually exhaust all the transaction credits if the IO contains many single block extents. Once that happens a WARN_ON(jbd2_handle_buffer_credits(handle) <= 0) is triggered in jbd2_journal_dirty_metadata() and subsequently OCFS2 aborts in response to this error. This was actually triggered by one of our customers on a heavily fragmented OCFS2 filesystem. To fix the issue make sure the transaction always has enough credits for one extent insert before each call of ocfs2_mark_extent_written(). Heming Zhao said: ------ PANIC: "Kernel panic - not syncing: OCFS2: (device dm-1): panic forced after error" PID: xxx TASK: xxxx CPU: 5 COMMAND: "SubmitThread-CA" #0 machine_kexec at ffffffff8c069932 #1 __crash_kexec at ffffffff8c1338fa #2 panic at ffffffff8c1d69b9 #3 ocfs2_handle_error at ffffffffc0c86c0c [ocfs2] #4 __ocfs2_abort at ffffffffc0c88387 [ocfs2] #5 ocfs2_journal_dirty at ffffffffc0c51e98 [ocfs2] #6 ocfs2_split_extent at ffffffffc0c27ea3 [ocfs2] #7 ocfs2_change_extent_flag at ffffffffc0c28053 [ocfs2] #8 ocfs2_mark_extent_written at ffffffffc0c28347 [ocfs2] #9 ocfs2_dio_end_io_write at ffffffffc0c2bef9 [ocfs2] #10 ocfs2_dio_end_io at ffffffffc0c2c0f5 [ocfs2] #11 dio_complete at ffffffff8c2b9fa7 #12 do_blockdev_direct_IO at ffffffff8c2bc09f #13 ocfs2_direct_IO at ffffffffc0c2b653 [ocfs2] #14 generic_file_direct_write at ffffffff8c1dcf14 #15 __generic_file_write_iter at ffffffff8c1dd07b #16 ocfs2_file_write_iter at ffffffffc0c49f1f [ocfs2] #17 aio_write at ffffffff8c2cc72e #18 kmem_cache_alloc at ffffffff8c248dde #19 do_io_submit at ffffffff8c2ccada #20 do_syscall_64 at ffffffff8c004984 #21 entry_SYSCALL_64_after_hwframe at ffffffff8c8000ba

In the Linux kernel, the following vulnerability has been resolved: tracefs: Use generic inode RCU for synchronizing freeing With structure layout randomization enabled for 'struct inode' we need to avoid overlapping any of the RCU-used / initialized-only-once members, e.g. i_lru or i_sb_list to not corrupt related list traversals when making use of the rcu_head. For an unlucky structure layout of 'struct inode' we may end up with the following splat when running the ftrace selftests: [<...>] list_del corruption, ffff888103ee2cb0->next (tracefs_inode_cache+0x0/0x4e0 [slab object]) is NULL (prev is tracefs_inode_cache+0x78/0x4e0 [slab object]) [<...>] ------------[ cut here ]------------ [<...>] kernel BUG at lib/list_debug.c:54! [<...>] invalid opcode: 0000 [#1] PREEMPT SMP KASAN [<...>] CPU: 3 PID: 2550 Comm: mount Tainted: G N 6.8.12-grsec+ #122 ed2f536ca62f28b087b90e3cc906a8d25b3ddc65 [<...>] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-2 04/01/2014 [<...>] RIP: 0010:[<ffffffff84656018>] __list_del_entry_valid_or_report+0x138/0x3e0 [<...>] Code: 48 b8 99 fb 65 f2 ff ff ff ff e9 03 5c d9 fc cc 48 b8 99 fb 65 f2 ff ff ff ff e9 33 5a d9 fc cc 48 b8 99 fb 65 f2 ff ff ff ff <0f> 0b 4c 89 e9 48 89 ea 48 89 ee 48 c7 c7 60 8f dd 89 31 c0 e8 2f [<...>] RSP: 0018:fffffe80416afaf0 EFLAGS: 00010283 [<...>] RAX: 0000000000000098 RBX: ffff888103ee2cb0 RCX: 0000000000000000 [<...>] RDX: ffffffff84655fe8 RSI: ffffffff89dd8b60 RDI: 0000000000000001 [<...>] RBP: ffff888103ee2cb0 R08: 0000000000000001 R09: fffffbd0082d5f25 [<...>] R10: fffffe80416af92f R11: 0000000000000001 R12: fdf99c16731d9b6d [<...>] R13: 0000000000000000 R14: ffff88819ad4b8b8 R15: 0000000000000000 [<...>] RBX: tracefs_inode_cache+0x0/0x4e0 [slab object] [<...>] RDX: __list_del_entry_valid_or_report+0x108/0x3e0 [<...>] RSI: __func__.47+0x4340/0x4400 [<...>] RBP: tracefs_inode_cache+0x0/0x4e0 [slab object] [<...>] RSP: process kstack fffffe80416afaf0+0x7af0/0x8000 [mount 2550 2550] [<...>] R09: kasan shadow of process kstack fffffe80416af928+0x7928/0x8000 [mount 2550 2550] [<...>] R10: process kstack fffffe80416af92f+0x792f/0x8000 [mount 2550 2550] [<...>] R14: tracefs_inode_cache+0x78/0x4e0 [slab object] [<...>] FS: 00006dcb380c1840(0000) GS:ffff8881e0600000(0000) knlGS:0000000000000000 [<...>] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [<...>] CR2: 000076ab72b30e84 CR3: 000000000b088004 CR4: 0000000000360ef0 shadow CR4: 0000000000360ef0 [<...>] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [<...>] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [<...>] ASID: 0003 [<...>] Stack: [<...>] ffffffff818a2315 00000000f5c856ee ffffffff896f1840 ffff888103ee2cb0 [<...>] ffff88812b6b9750 0000000079d714b6 fffffbfff1e9280b ffffffff8f49405f [<...>] 0000000000000001 0000000000000000 ffff888104457280 ffffffff8248b392 [<...>] Call Trace: [<...>] <TASK> [<...>] [<ffffffff818a2315>] ? lock_release+0x175/0x380 fffffe80416afaf0 [<...>] [<ffffffff8248b392>] list_lru_del+0x152/0x740 fffffe80416afb48 [<...>] [<ffffffff8248ba93>] list_lru_del_obj+0x113/0x280 fffffe80416afb88 [<...>] [<ffffffff8940fd19>] ? _atomic_dec_and_lock+0x119/0x200 fffffe80416afb90 [<...>] [<ffffffff8295b244>] iput_final+0x1c4/0x9a0 fffffe80416afbb8 [<...>] [<ffffffff8293a52b>] dentry_unlink_inode+0x44b/0xaa0 fffffe80416afbf8 [<...>] [<ffffffff8293fefc>] __dentry_kill+0x23c/0xf00 fffffe80416afc40 [<...>] [<ffffffff8953a85f>] ? __this_cpu_preempt_check+0x1f/0xa0 fffffe80416afc48 [<...>] [<ffffffff82949ce5>] ? shrink_dentry_list+0x1c5/0x760 fffffe80416afc70 [<...>] [<ffffffff82949b71>] ? shrink_dentry_list+0x51/0x760 fffffe80416afc78 [<...>] [<ffffffff82949da8>] shrink_dentry_list+0x288/0x760 fffffe80416afc80 [<...>] [<ffffffff8294ae75>] shrink_dcache_sb+0x155/0x420 fffffe80416afcc8 [<...>] [<ffffffff8953a7c3>] ? debug_smp_processor_id+0x23/0xa0 fffffe80416afce0 [<...>] [<ffffffff8294ad20>] ? do_one_tre ---truncated---

In the Linux kernel, the following vulnerability has been resolved: xprtrdma: treat all calls not a bcall when bc_serv is NULL When a rdma server returns a fault format reply, nfs v3 client may treats it as a bcall when bc service is not exist. The debug message at rpcrdma_bc_receive_call are, [56579.837169] RPC: rpcrdma_bc_receive_call: callback XID 00000001, length=20 [56579.837174] RPC: rpcrdma_bc_receive_call: 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 04 After that, rpcrdma_bc_receive_call will meets NULL pointer as, [ 226.057890] BUG: unable to handle kernel NULL pointer dereference at 00000000000000c8 ... [ 226.058704] RIP: 0010:_raw_spin_lock+0xc/0x20 ... [ 226.059732] Call Trace: [ 226.059878] rpcrdma_bc_receive_call+0x138/0x327 [rpcrdma] [ 226.060011] __ib_process_cq+0x89/0x170 [ib_core] [ 226.060092] ib_cq_poll_work+0x26/0x80 [ib_core] [ 226.060257] process_one_work+0x1a7/0x360 [ 226.060367] ? create_worker+0x1a0/0x1a0 [ 226.060440] worker_thread+0x30/0x390 [ 226.060500] ? create_worker+0x1a0/0x1a0 [ 226.060574] kthread+0x116/0x130 [ 226.060661] ? kthread_flush_work_fn+0x10/0x10 [ 226.060724] ret_from_fork+0x35/0x40 ...

In the Linux kernel, the following vulnerability has been resolved: RDMA/mlx5: Initialize the ODP xarray when creating an ODP MR Normally the zero fill would hide the missing initialization, but an errant set to desc_size in reg_create() causes a crash: BUG: unable to handle page fault for address: 0000000800000000 PGD 0 P4D 0 Oops: 0000 [#1] SMP PTI CPU: 5 PID: 890 Comm: ib_write_bw Not tainted 5.15.0-rc4+ #47 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 RIP: 0010:mlx5_ib_dereg_mr+0x14/0x3b0 [mlx5_ib] Code: 48 63 cd 4c 89 f7 48 89 0c 24 e8 37 30 03 e1 48 8b 0c 24 eb a0 90 0f 1f 44 00 00 41 56 41 55 41 54 55 53 48 89 fb 48 83 ec 30 <48> 8b 2f 65 48 8b 04 25 28 00 00 00 48 89 44 24 28 31 c0 8b 87 c8 RSP: 0018:ffff88811afa3a60 EFLAGS: 00010286 RAX: 000000000000001c RBX: 0000000800000000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000800000000 RBP: 0000000800000000 R08: 0000000000000000 R09: c0000000fffff7ff R10: ffff88811afa38f8 R11: ffff88811afa38f0 R12: ffffffffa02c7ac0 R13: 0000000000000000 R14: ffff88811afa3cd8 R15: ffff88810772fa00 FS: 00007f47b9080740(0000) GS:ffff88852cd40000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000800000000 CR3: 000000010761e003 CR4: 0000000000370ea0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: mlx5_ib_free_odp_mr+0x95/0xc0 [mlx5_ib] mlx5_ib_dereg_mr+0x128/0x3b0 [mlx5_ib] ib_dereg_mr_user+0x45/0xb0 [ib_core] ? xas_load+0x8/0x80 destroy_hw_idr_uobject+0x1a/0x50 [ib_uverbs] uverbs_destroy_uobject+0x2f/0x150 [ib_uverbs] uobj_destroy+0x3c/0x70 [ib_uverbs] ib_uverbs_cmd_verbs+0x467/0xb00 [ib_uverbs] ? uverbs_finalize_object+0x60/0x60 [ib_uverbs] ? ttwu_queue_wakelist+0xa9/0xe0 ? pty_write+0x85/0x90 ? file_tty_write.isra.33+0x214/0x330 ? process_echoes+0x60/0x60 ib_uverbs_ioctl+0xa7/0x110 [ib_uverbs] __x64_sys_ioctl+0x10d/0x8e0 ? vfs_write+0x17f/0x260 do_syscall_64+0x3c/0x80 entry_SYSCALL_64_after_hwframe+0x44/0xae Add the missing xarray initialization and remove the desc_size set.

In the Linux kernel, the following vulnerability has been resolved: ata: libata-transport: fix error handling in ata_tlink_add() In ata_tlink_add(), the return value of transport_add_device() is not checked. As a result, it causes null-ptr-deref while removing the module, because transport_remove_device() is called to remove the device that was not added. Unable to handle kernel NULL pointer dereference at virtual address 00000000000000d0 CPU: 33 PID: 13850 Comm: rmmod Kdump: loaded Tainted: G W 6.1.0-rc3+ #12 pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : device_del+0x48/0x39c lr : device_del+0x44/0x39c Call trace: device_del+0x48/0x39c attribute_container_class_device_del+0x28/0x40 transport_remove_classdev+0x60/0x7c attribute_container_device_trigger+0x118/0x120 transport_remove_device+0x20/0x30 ata_tlink_delete+0x88/0xb0 [libata] ata_tport_delete+0x2c/0x60 [libata] ata_port_detach+0x148/0x1b0 [libata] ata_pci_remove_one+0x50/0x80 [libata] ahci_remove_one+0x4c/0x8c [ahci] Fix this by checking and handling return value of transport_add_device() in ata_tlink_add().

In the Linux kernel, the following vulnerability has been resolved: drm/msm: Fix null pointer dereferences without iommu Check if 'aspace' is set before using it as it will stay null without IOMMU, such as on msm8974.

In the Linux kernel, the following vulnerability has been resolved: net: ethernet: ti: am65-cpsw-nuss: Fix some refcount leaks of_get_child_by_name() returns a node pointer with refcount incremented, we should use of_node_put() on it when not need anymore. am65_cpsw_init_cpts() and am65_cpsw_nuss_probe() don't release the refcount in error case. Add missing of_node_put() to avoid refcount leak.

In the Linux kernel, the following vulnerability has been resolved: nfc: nfcmrvl: Fix potential memory leak in nfcmrvl_i2c_nci_send() nfcmrvl_i2c_nci_send() will be called by nfcmrvl_nci_send(), and skb should be freed in nfcmrvl_i2c_nci_send(). However, nfcmrvl_nci_send() will only free skb when i2c_master_send() return >=0, which means skb will memleak when i2c_master_send() failed. Free skb no matter whether i2c_master_send() succeeds.

In the Linux kernel, the following vulnerability has been resolved: octeontx2-af: Fix mcam entry resource leak The teardown sequence in FLR handler returns if no NIX LF is attached to PF/VF because it indicates that graceful shutdown of resources already happened. But there is a chance of all allocated MCAM entries not being freed by PF/VF. Hence free mcam entries even in case of detached LF.

In the Linux kernel, the following vulnerability has been resolved: chardev: fix error handling in cdev_device_add() While doing fault injection test, I got the following report: ------------[ cut here ]------------ kobject: '(null)' (0000000039956980): is not initialized, yet kobject_put() is being called. WARNING: CPU: 3 PID: 6306 at kobject_put+0x23d/0x4e0 CPU: 3 PID: 6306 Comm: 283 Tainted: G W 6.1.0-rc2-00005-g307c1086d7c9 #1253 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014 RIP: 0010:kobject_put+0x23d/0x4e0 Call Trace: <TASK> cdev_device_add+0x15e/0x1b0 __iio_device_register+0x13b4/0x1af0 [industrialio] __devm_iio_device_register+0x22/0x90 [industrialio] max517_probe+0x3d8/0x6b4 [max517] i2c_device_probe+0xa81/0xc00 When device_add() is injected fault and returns error, if dev->devt is not set, cdev_add() is not called, cdev_del() is not needed. Fix this by checking dev->devt in error path.

In the Linux kernel, the following vulnerability has been resolved: wifi: carl9170: add a proper sanity check for endpoints Syzkaller reports [1] hitting a warning which is caused by presence of a wrong endpoint type at the URB sumbitting stage. While there was a check for a specific 4th endpoint, since it can switch types between bulk and interrupt, other endpoints are trusted implicitly. Similar warning is triggered in a couple of other syzbot issues [2]. Fix the issue by doing a comprehensive check of all endpoints taking into account difference between high- and full-speed configuration. [1] Syzkaller report: ... WARNING: CPU: 0 PID: 4721 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504 ... Call Trace: <TASK> carl9170_usb_send_rx_irq_urb+0x273/0x340 drivers/net/wireless/ath/carl9170/usb.c:504 carl9170_usb_init_device drivers/net/wireless/ath/carl9170/usb.c:939 [inline] carl9170_usb_firmware_finish drivers/net/wireless/ath/carl9170/usb.c:999 [inline] carl9170_usb_firmware_step2+0x175/0x240 drivers/net/wireless/ath/carl9170/usb.c:1028 request_firmware_work_func+0x130/0x240 drivers/base/firmware_loader/main.c:1107 process_one_work+0x9bf/0x1710 kernel/workqueue.c:2289 worker_thread+0x669/0x1090 kernel/workqueue.c:2436 kthread+0x2e8/0x3a0 kernel/kthread.c:376 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:308 </TASK> [2] Related syzkaller crashes:

In the Linux kernel, the following vulnerability has been resolved: skmsg: Fix wrong last sg check in sk_msg_recvmsg() Fix one kernel NULL pointer dereference as below: [ 224.462334] Call Trace: [ 224.462394] __tcp_bpf_recvmsg+0xd3/0x380 [ 224.462441] ? sock_has_perm+0x78/0xa0 [ 224.462463] tcp_bpf_recvmsg+0x12e/0x220 [ 224.462494] inet_recvmsg+0x5b/0xd0 [ 224.462534] __sys_recvfrom+0xc8/0x130 [ 224.462574] ? syscall_trace_enter+0x1df/0x2e0 [ 224.462606] ? __do_page_fault+0x2de/0x500 [ 224.462635] __x64_sys_recvfrom+0x24/0x30 [ 224.462660] do_syscall_64+0x5d/0x1d0 [ 224.462709] entry_SYSCALL_64_after_hwframe+0x65/0xca In commit 9974d37ea75f ("skmsg: Fix invalid last sg check in sk_msg_recvmsg()"), we change last sg check to sg_is_last(), but in sockmap redirection case (without stream_parser/stream_verdict/ skb_verdict), we did not mark the end of the scatterlist. Check the sk_msg_alloc, sk_msg_page_add, and bpf_msg_push_data functions, they all do not mark the end of sg. They are expected to use sg.end for end judgment. So the judgment of '(i != msg_rx->sg.end)' is added back here.

In the Linux kernel, the following vulnerability has been resolved: MIPS: smp: fill in sibling and core maps earlier After enabling CONFIG_SCHED_CORE (landed during 5.14 cycle), 2-core 2-thread-per-core interAptiv (CPS-driven) started emitting the following: [ 0.025698] CPU1 revision is: 0001a120 (MIPS interAptiv (multi)) [ 0.048183] ------------[ cut here ]------------ [ 0.048187] WARNING: CPU: 1 PID: 0 at kernel/sched/core.c:6025 sched_core_cpu_starting+0x198/0x240 [ 0.048220] Modules linked in: [ 0.048233] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.17.0-rc3+ #35 b7b319f24073fd9a3c2aa7ad15fb7993eec0b26f [ 0.048247] Stack : 817f0000 00000004 327804c8 810eb050 00000000 00000004 00000000 c314fdd1 [ 0.048278] 830cbd64 819c0000 81800000 817f0000 83070bf4 00000001 830cbd08 00000000 [ 0.048307] 00000000 00000000 815fcbc4 00000000 00000000 00000000 00000000 00000000 [ 0.048334] 00000000 00000000 00000000 00000000 817f0000 00000000 00000000 817f6f34 [ 0.048361] 817f0000 818a3c00 817f0000 00000004 00000000 00000000 4dc33260 0018c933 [ 0.048389] ... [ 0.048396] Call Trace: [ 0.048399] [<8105a7bc>] show_stack+0x3c/0x140 [ 0.048424] [<8131c2a0>] dump_stack_lvl+0x60/0x80 [ 0.048440] [<8108b5c0>] __warn+0xc0/0xf4 [ 0.048454] [<8108b658>] warn_slowpath_fmt+0x64/0x10c [ 0.048467] [<810bd418>] sched_core_cpu_starting+0x198/0x240 [ 0.048483] [<810c6514>] sched_cpu_starting+0x14/0x80 [ 0.048497] [<8108c0f8>] cpuhp_invoke_callback_range+0x78/0x140 [ 0.048510] [<8108d914>] notify_cpu_starting+0x94/0x140 [ 0.048523] [<8106593c>] start_secondary+0xbc/0x280 [ 0.048539] [ 0.048543] ---[ end trace 0000000000000000 ]--- [ 0.048636] Synchronize counters for CPU 1: done. ...for each but CPU 0/boot. Basic debug printks right before the mentioned line say: [ 0.048170] CPU: 1, smt_mask: So smt_mask, which is sibling mask obviously, is empty when entering the function. This is critical, as sched_core_cpu_starting() calculates core-scheduling parameters only once per CPU start, and it's crucial to have all the parameters filled in at that moment (at least it uses cpu_smt_mask() which in fact is `&cpu_sibling_map[cpu]` on MIPS). A bit of debugging led me to that set_cpu_sibling_map() performing the actual map calculation, was being invocated after notify_cpu_start(), and exactly the latter function starts CPU HP callback round (sched_core_cpu_starting() is basically a CPU HP callback). While the flow is same on ARM64 (maps after the notifier, although before calling set_cpu_online()), x86 started calculating sibling maps earlier than starting the CPU HP callbacks in Linux 4.14 (see [0] for the reference). Neither me nor my brief tests couldn't find any potential caveats in calculating the maps right after performing delay calibration, but the WARN splat is now gone. The very same debug prints now yield exactly what I expected from them: [ 0.048433] CPU: 1, smt_mask: 0-1 [0] https://git.kernel.org/pub/scm/linux/kernel/git/mips/linux.git/commit/?id=76ce7cfe35ef

In the Linux kernel, the following vulnerability has been resolved: x86/tdx: Panic on bad configs that #VE on "private" memory access All normal kernel memory is "TDX private memory". This includes everything from kernel stacks to kernel text. Handling exceptions on arbitrary accesses to kernel memory is essentially impossible because they can happen in horribly nasty places like kernel entry/exit. But, TDX hardware can theoretically _deliver_ a virtualization exception (#VE) on any access to private memory. But, it's not as bad as it sounds. TDX can be configured to never deliver these exceptions on private memory with a "TD attribute" called ATTR_SEPT_VE_DISABLE. The guest has no way to *set* this attribute, but it can check it. Ensure ATTR_SEPT_VE_DISABLE is set in early boot. panic() if it is unset. There is no sane way for Linux to run with this attribute clear so a panic() is appropriate. There's small window during boot before the check where kernel has an early #VE handler. But the handler is only for port I/O and will also panic() as soon as it sees any other #VE, such as a one generated by a private memory access. [ dhansen: Rewrite changelog and rebase on new tdx_parse_tdinfo(). Add Kirill's tested-by because I made changes since he wrote this. ]

In the Linux kernel, the following vulnerability has been resolved: media: mgb4: Fix double debugfs remove Fixes an error where debugfs_remove_recursive() is called first on a parent directory and then again on a child which causes a kernel panic. [hverkuil: added Fixes/Cc tags]

In the Linux kernel, the following vulnerability has been resolved: powerpc/64s: Don't use DSISR for SLB faults Since commit 46ddcb3950a2 ("powerpc/mm: Show if a bad page fault on data is read or write.") we use page_fault_is_write(regs->dsisr) in __bad_page_fault() to determine if the fault is for a read or write, and change the message printed accordingly. But SLB faults, aka Data Segment Interrupts, don't set DSISR (Data Storage Interrupt Status Register) to a useful value. All ISA versions from v2.03 through v3.1 specify that the Data Segment Interrupt sets DSISR "to an undefined value". As far as I can see there's no mention of SLB faults setting DSISR in any BookIV content either. This manifests as accesses that should be a read being incorrectly reported as writes, for example, using the xmon "dump" command: 0:mon> d 0x5deadbeef0000000 5deadbeef0000000 [359526.415354][ C6] BUG: Unable to handle kernel data access on write at 0x5deadbeef0000000 [359526.415611][ C6] Faulting instruction address: 0xc00000000010a300 cpu 0x6: Vector: 380 (Data SLB Access) at [c00000000ffbf400] pc: c00000000010a300: mread+0x90/0x190 If we disassemble the PC, we see a load instruction: 0:mon> di c00000000010a300 c00000000010a300 89490000 lbz r10,0(r9) We can also see in exceptions-64s.S that the data_access_slb block doesn't set IDSISR=1, which means it doesn't load DSISR into pt_regs. So the value we're using to determine if the fault is a read/write is some stale value in pt_regs from a previous page fault. Rework the printing logic to separate the SLB fault case out, and only print read/write in the cases where we can determine it. The result looks like eg: 0:mon> d 0x5deadbeef0000000 5deadbeef0000000 [ 721.779525][ C6] BUG: Unable to handle kernel data access at 0x5deadbeef0000000 [ 721.779697][ C6] Faulting instruction address: 0xc00000000014cbe0 cpu 0x6: Vector: 380 (Data SLB Access) at [c00000000ffbf390] 0:mon> d 0 0000000000000000 [ 742.793242][ C6] BUG: Kernel NULL pointer dereference at 0x00000000 [ 742.793316][ C6] Faulting instruction address: 0xc00000000014cbe0 cpu 0x6: Vector: 380 (Data SLB Access) at [c00000000ffbf390]

In the Linux kernel, the following vulnerability has been resolved: media: s5p_cec: limit msg.len to CEC_MAX_MSG_SIZE I expect that the hardware will have limited this to 16, but just in case it hasn't, check for this corner case.

In the Linux kernel, the following vulnerability has been resolved: crypto: starfive - Do not free stack buffer RSA text data uses variable length buffer allocated in software stack. Calling kfree on it causes undefined behaviour in subsequent operations.

In the Linux kernel, the following vulnerability has been resolved: RDMA/irdma: Fix sleep from invalid context BUG Taking the qos_mutex to process RoCEv2 QP's on netdev events causes a kernel splat. Fix this by removing the handling for RoCEv2 in irdma_cm_teardown_connections that uses the mutex. This handling is only needed for iWARP to avoid having connections established while the link is down or having connections remain functional after the IP address is removed. BUG: sleeping function called from invalid context at kernel/locking/mutex. Call Trace: kernel: dump_stack+0x66/0x90 kernel: ___might_sleep.cold.92+0x8d/0x9a kernel: mutex_lock+0x1c/0x40 kernel: irdma_cm_teardown_connections+0x28e/0x4d0 [irdma] kernel: ? check_preempt_curr+0x7a/0x90 kernel: ? select_idle_sibling+0x22/0x3c0 kernel: ? select_task_rq_fair+0x94c/0xc90 kernel: ? irdma_exec_cqp_cmd+0xc27/0x17c0 [irdma] kernel: ? __wake_up_common+0x7a/0x190 kernel: irdma_if_notify+0x3cc/0x450 [irdma] kernel: ? sched_clock_cpu+0xc/0xb0 kernel: irdma_inet6addr_event+0xc6/0x150 [irdma]

In the Linux kernel, the following vulnerability has been resolved: soc: rockchip: Fix refcount leak in rockchip_grf_init of_find_matching_node_and_match returns a node pointer with refcount incremented, we should use of_node_put() on it when done. Add missing of_node_put() to avoid refcount leak.

In the Linux kernel, the following vulnerability has been resolved: net: tipc: fix possible refcount leak in tipc_sk_create() Free sk in case tipc_sk_insert() fails.

In the Linux kernel, the following vulnerability has been resolved: ASoC: SOF: ipc4-topology: Fix input format query of process modules without base extension If a process module does not have base config extension then the same format applies to all of it's inputs and the process->base_config_ext is NULL, causing NULL dereference when specifically crafted topology and sequences used.

In the Linux kernel, the following vulnerability has been resolved: netrom: fix possible dead-lock in nr_rt_ioctl() syzbot loves netrom, and found a possible deadlock in nr_rt_ioctl [1] Make sure we always acquire nr_node_list_lock before nr_node_lock(nr_node) [1] WARNING: possible circular locking dependency detected 6.9.0-rc7-syzkaller-02147-g654de42f3fc6 #0 Not tainted ------------------------------------------------------ syz-executor350/5129 is trying to acquire lock: ffff8880186e2070 (&nr_node->node_lock){+...}-{2:2}, at: spin_lock_bh include/linux/spinlock.h:356 [inline] ffff8880186e2070 (&nr_node->node_lock){+...}-{2:2}, at: nr_node_lock include/net/netrom.h:152 [inline] ffff8880186e2070 (&nr_node->node_lock){+...}-{2:2}, at: nr_dec_obs net/netrom/nr_route.c:464 [inline] ffff8880186e2070 (&nr_node->node_lock){+...}-{2:2}, at: nr_rt_ioctl+0x1bb/0x1090 net/netrom/nr_route.c:697 but task is already holding lock: ffffffff8f7053b8 (nr_node_list_lock){+...}-{2:2}, at: spin_lock_bh include/linux/spinlock.h:356 [inline] ffffffff8f7053b8 (nr_node_list_lock){+...}-{2:2}, at: nr_dec_obs net/netrom/nr_route.c:462 [inline] ffffffff8f7053b8 (nr_node_list_lock){+...}-{2:2}, at: nr_rt_ioctl+0x10a/0x1090 net/netrom/nr_route.c:697 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (nr_node_list_lock){+...}-{2:2}: lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5754 __raw_spin_lock_bh include/linux/spinlock_api_smp.h:126 [inline] _raw_spin_lock_bh+0x35/0x50 kernel/locking/spinlock.c:178 spin_lock_bh include/linux/spinlock.h:356 [inline] nr_remove_node net/netrom/nr_route.c:299 [inline] nr_del_node+0x4b4/0x820 net/netrom/nr_route.c:355 nr_rt_ioctl+0xa95/0x1090 net/netrom/nr_route.c:683 sock_do_ioctl+0x158/0x460 net/socket.c:1222 sock_ioctl+0x629/0x8e0 net/socket.c:1341 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:904 [inline] __se_sys_ioctl+0xfc/0x170 fs/ioctl.c:890 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf5/0x240 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f -> #0 (&nr_node->node_lock){+...}-{2:2}: check_prev_add kernel/locking/lockdep.c:3134 [inline] check_prevs_add kernel/locking/lockdep.c:3253 [inline] validate_chain+0x18cb/0x58e0 kernel/locking/lockdep.c:3869 __lock_acquire+0x1346/0x1fd0 kernel/locking/lockdep.c:5137 lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5754 __raw_spin_lock_bh include/linux/spinlock_api_smp.h:126 [inline] _raw_spin_lock_bh+0x35/0x50 kernel/locking/spinlock.c:178 spin_lock_bh include/linux/spinlock.h:356 [inline] nr_node_lock include/net/netrom.h:152 [inline] nr_dec_obs net/netrom/nr_route.c:464 [inline] nr_rt_ioctl+0x1bb/0x1090 net/netrom/nr_route.c:697 sock_do_ioctl+0x158/0x460 net/socket.c:1222 sock_ioctl+0x629/0x8e0 net/socket.c:1341 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:904 [inline] __se_sys_ioctl+0xfc/0x170 fs/ioctl.c:890 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf5/0x240 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(nr_node_list_lock); lock(&nr_node->node_lock); lock(nr_node_list_lock); lock(&nr_node->node_lock); *** DEADLOCK *** 1 lock held by syz-executor350/5129: #0: ffffffff8f7053b8 (nr_node_list_lock){+...}-{2:2}, at: spin_lock_bh include/linux/spinlock.h:356 [inline] #0: ffffffff8f7053b8 (nr_node_list_lock){+...}-{2:2}, at: nr_dec_obs net/netrom/nr_route.c:462 [inline] #0: ffffffff8f70 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: RDMA/rxe: Fix error unwind in rxe_create_qp() In the function rxe_create_qp(), rxe_qp_from_init() is called to initialize qp, internally things like the spin locks are not setup until rxe_qp_init_req(). If an error occures before this point then the unwind will call rxe_cleanup() and eventually to rxe_qp_do_cleanup()/rxe_cleanup_task() which will oops when trying to access the uninitialized spinlock. Move the spinlock initializations earlier before any failures.

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix deadlock in smb2_find_smb_tcon() Unlock cifs_tcp_ses_lock before calling cifs_put_smb_ses() to avoid such deadlock.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: fix array index out of bound error in DCN32 DML [Why&How] LinkCapacitySupport array is indexed with the number of voltage states and not the number of max DPPs. Fix the error by changing the array declaration to use the correct (larger) array size of total number of voltage states.

In the Linux kernel, the following vulnerability has been resolved: ax25: Fix reference count leak issues of ax25_dev The ax25_addr_ax25dev() and ax25_dev_device_down() exist a reference count leak issue of the object "ax25_dev". Memory leak issue in ax25_addr_ax25dev(): The reference count of the object "ax25_dev" can be increased multiple times in ax25_addr_ax25dev(). This will cause a memory leak. Memory leak issues in ax25_dev_device_down(): The reference count of ax25_dev is set to 1 in ax25_dev_device_up() and then increase the reference count when ax25_dev is added to ax25_dev_list. As a result, the reference count of ax25_dev is 2. But when the device is shutting down. The ax25_dev_device_down() drops the reference count once or twice depending on if we goto unlock_put or not, which will cause memory leak. As for the issue of ax25_addr_ax25dev(), it is impossible for one pointer to be on a list twice. So add a break in ax25_addr_ax25dev(). As for the issue of ax25_dev_device_down(), increase the reference count of ax25_dev once in ax25_dev_device_up() and decrease the reference count of ax25_dev after it is removed from the ax25_dev_list.

In the Linux kernel, the following vulnerability has been resolved: device property: fix of node refcount leak in fwnode_graph_get_next_endpoint() The 'parent' returned by fwnode_graph_get_port_parent() with refcount incremented when 'prev' is not NULL, it needs be put when finish using it. Because the parent is const, introduce a new variable to store the returned fwnode, then put it before returning from fwnode_graph_get_next_endpoint().

In the Linux kernel, the following vulnerability has been resolved: RDMA/rxe: Fix BUG: KASAN: null-ptr-deref in rxe_qp_do_cleanup The function rxe_create_qp calls rxe_qp_from_init. If some error occurs, the error handler of function rxe_qp_from_init will set both scq and rcq to NULL. Then rxe_create_qp calls rxe_put to handle qp. In the end, rxe_qp_do_cleanup is called by rxe_put. rxe_qp_do_cleanup directly accesses scq and rcq before checking them. This will cause null-ptr-deref error. The call graph is as below: rxe_create_qp { ... rxe_qp_from_init { ... err1: ... qp->rcq = NULL; <---rcq is set to NULL qp->scq = NULL; <---scq is set to NULL ... } qp_init: rxe_put{ ... rxe_qp_do_cleanup { ... atomic_dec(&qp->scq->num_wq); <--- scq is accessed ... atomic_dec(&qp->rcq->num_wq); <--- rcq is accessed } }

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix NULL deref in mlx5e_tir_builder_alloc() In mlx5e_tir_builder_alloc() kvzalloc() may return NULL which is dereferenced on the next line in a reference to the modify field. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: drivers: serial: jsm: fix some leaks in probe This error path needs to unwind instead of just returning directly.

In the Linux kernel, the following vulnerability has been resolved: phy: ralink: mt7621-pci: add sentinel to quirks table With mt7621 soc_dev_attr fixed to register the soc as a device, kernel will experience an oops in soc_device_match_attr This quirk test was introduced in the staging driver in commit 9445ccb3714c ("staging: mt7621-pci-phy: add quirks for 'E2' revision using 'soc_device_attribute'"). The staging driver was removed, and later re-added in commit d87da32372a0 ("phy: ralink: Add PHY driver for MT7621 PCIe PHY") for kernel 5.11

In the Linux kernel, the following vulnerability has been resolved: capabilities: fix potential memleak on error path from vfs_getxattr_alloc() In cap_inode_getsecurity(), we will use vfs_getxattr_alloc() to complete the memory allocation of tmpbuf, if we have completed the memory allocation of tmpbuf, but failed to call handler->get(...), there will be a memleak in below logic: |-- ret = (int)vfs_getxattr_alloc(mnt_userns, ...) | /* ^^^ alloc for tmpbuf */ |-- value = krealloc(*xattr_value, error + 1, flags) | /* ^^^ alloc memory */ |-- error = handler->get(handler, ...) | /* error! */ |-- *xattr_value = value | /* xattr_value is &tmpbuf (memory leak!) */ So we will try to free(tmpbuf) after vfs_getxattr_alloc() fails to fix it. [PM: subject line and backtrace tweaks]