A command injection vulnerability exists in the D-Link DIR-882 Router firmware DIR882A1_FW102B02 within the `prog.cgi` and `librcm.so` binaries. The `sub_4455BC` function in `prog.cgi` stores user-supplied `SetDMZSettings/IPAddress` values in NVRAM via `nvram_safe_set("dmz_ipaddr", ...)`. These values are later retrieved in the `DMZ_run` function of `librcm.so` using `nvram_safe_get` and concatenated into `iptables` shell commands executed via `twsystem()` without any sanitization. An unauthenticated remote attacker can exploit this vulnerability to execute arbitrary commands on the device through specially crafted HTTP requests to the router's web interface.

An unauthenticated command injection vulnerability exists in the D-Link DIR-878A1 router firmware FW101B04.bin. The vulnerability occurs in the 'SetDMZSettings' functionality, where the 'IPAddress' parameter in prog.cgi is stored in NVRAM and later used by librcm.so to construct iptables commands executed via twsystem(). An attacker can exploit this vulnerability remotely without authentication by sending a specially crafted HTTP request, leading to arbitrary command execution on the device.

A command injection vulnerability exists in the D-Link DIR-882 Router firmware DIR882A1_FW102B02 within the `prog.cgi` and `rc` binaries. The `sub_433188` function in `prog.cgi` stores user-supplied email configuration parameters (`EmailFrom`, `EmailTo`, `SMTPServerAddress`, `SMTPServerPort`, `AccountName`) in NVRAM via `nvram_safe_set`. These values are later retrieved in the `sub_448FDC` function of `rc` using `nvram_safe_get` and concatenated into shell commands executed via `twsystem()` without sanitization. An unauthenticated remote attacker can exploit this vulnerability to execute arbitrary commands on the device through specially crafted HTTP requests to the router's web interface.

An unauthenticated command injection vulnerability exists in the D-Link DIR-878A1 router firmware FW101B04.bin. The vulnerability occurs in the 'SetDynamicDNSSettings' functionality, where the 'ServerAddress' and 'Hostname' parameters in prog.cgi are stored in NVRAM and later used by rc to construct system commands executed via twsystem(). An attacker can exploit this vulnerability remotely without authentication by sending a specially crafted HTTP request, leading to arbitrary command execution on the device.

An unauthenticated command injection vulnerability exists in the D-Link DIR-878A1 router firmware FW101B04.bin. The vulnerability occurs in the 'SetNetworkSettings' functionality of prog.cgi, where the 'IPAddress' and 'SubnetMask' parameters are directly concatenated into shell commands executed via system(). An attacker can exploit this vulnerability remotely without authentication by sending a specially crafted HTTP request, leading to arbitrary command execution on the device.

Hardcoded credentials in the Telnet service in D-Link DIR-605L v2.13B01 and DIR-816L v2.06B01 allow attackers to remotely execute arbitrary commands via firmware analysis.

D-Link DSL-7740C with firmware DSL7740C.V6.TR069.20211230 was discovered to contain a command injection vulnerability via the ping function.

OS Command injection vulnerability in D-Link C1 2020-02-21. The sub_47F028 function in jhttpd contains a command injection vulnerability via the HTTP parameter "time".

An access control issue in the component form2RepeaterSetup.cgi of D-Link 816A2_FWv1.10CNB05_R1B011D88210 allows unauthenticated attackers to set the 2.4G and 5G repeater service of the device via a crafted POST request.

An access control issue in the component form2WlanBasicSetup.cgi of D-Link 816A2_FWv1.10CNB05_R1B011D88210 allows unauthenticated attackers to set the 2.4G and 5G wlan service of the device via a crafted POST request.

An access control issue in the component form2WlAc.cgi of D-Link 816A2_FWv1.10CNB05_R1B011D88210 allows unauthenticated attackers to set the 2.4G and 5G mac access control list of the device via a crafted POST request.

An access control issue in the component form2Wan.cgi of D-Link 816A2_FWv1.10CNB05_R1B011D88210 allows unauthenticated attackers to set the wan service of the device via a crafted POST request.

D-Link DSL-2750B devices before 1.05 allow remote unauthenticated command injection via the login.cgi cli parameter, as exploited in the wild in 2016 through 2022.

An issue was discovered on the D-Link DWR-932B router. qmiweb allows command injection with ` characters.

A vulnerability was found in D-Link DI-8003 16.07.16A1. It has been classified as critical. Affected is the function upgrade_filter_asp of the file /upgrade_filter.asp. The manipulation of the argument path leads to os command injection. It is possible to launch the attack remotely. The exploit has been disclosed to the public and may be used.

A command injection in the parsing_xml_stasurvey function inside libcgifunc.so of the D-Link DAP-X1860 repeater 1.00 through 1.01b05-01 allows attackers (within range of the repeater) to run shell commands as root during the setup process of the repeater, via a crafted SSID. Also, network names containing single quotes (in the range of the repeater) can result in a denial of service.

An issue found in D-Link DSL-3782 v.1.03 and before allows remote authenticated users to execute arbitrary code as root via the Router IP Address fields of the network settings page.

D-Link DI-7003GV2 v24.04.18D1, DI-7100G+V2 v24.04.18D1, DI-7100GV2 v24.04.18D1, DI-7200GV2 v24.04.18E1, DI-7300G+V2 v24.04.18D1, and DI-7400G+V2 v24.04.18D1 are vulnerable to Remote Command Execution due to insufficient parameter filtering in the CGI handling function of upgrade_filter.asp.

D-Link DI-7003G v19.12.24A1, DI-7003GV2 v24.04.18D1, DI-7100G+V2 v24.04.18D1, DI-7100GV2 v24.04.18D1, DI-7200GV2 v24.04.18E1, DI-7300G+V2 v24.04.18D1, and DI-7400G+V2 v24.04.18D1 are vulnerable to Remote Command Execution (RCE) via version_upgrade.asp.

D-Link DI-8300 v16.07.26A1 is vulnerable to command injection via the upgrade_filter_asp function.

D-Link DI-8100G 17.12.20A1 is vulnerable to Command Injection via sub47A60C function in the upgrade_filter.asp file

D-LINK DWL-6610 FW_v_4.3.0.8B003C was discovered to contain a command injection vulnerability in the function pcap_download_handler. This vulnerability allows attackers to execute arbitrary commands via the update.device.packet-capture.tftp-file-name parameter.

A vulnerability was discovered in DI_8200-16.07.26A1, which has been classified as critical. This issue affects the upgrade_filter_asp function in the upgrade_filter.asp file. Manipulation of the path parameter can lead to command injection.

D-LINK DWL-6610 FW_v_4.3.0.8B003C was discovered to contain a command injection vulnerability in the function web_cert_download_handler. This vulnerability allows attackers to execute arbitrary commands via the certDownload parameter.

D-LINK DWL-6610 FW_v_4.3.0.8B003C was discovered to contain a command injection vulnerability in the function sub_2EF50. This vulnerability allows attackers to execute arbitrary commands via the manual-time-string parameter.

A command injection vulnerability exists in the D-Link DIR-882 Router firmware DIR882A1_FW102B02 within the `prog.cgi` and `rc` binaries. The `sub_4438A4` function in `prog.cgi` stores user-supplied DDNS parameters (`ServerAddress` and `Hostname`) in NVRAM via `nvram_safe_set`. These values are later retrieved in the `start_DDNS_ipv4` function of `rc` using `nvram_safe_get` and concatenated into DDNS shell commands executed via `twsystem()` without proper sanitization. Partial string comparison is performed but is insufficient to prevent command injection. An unauthenticated remote attacker can exploit this vulnerability to execute arbitrary commands on the device through specially crafted HTTP requests to the router's web interface.

The D-Link DIR-645 Wired/Wireless Router Rev. Ax with firmware 1.04b12 and earlier allows remote attackers to execute arbitrary commands via a GetDeviceSettings action to the HNAP interface.

A vulnerability has been found in D-Link R15 (AX1500) 1.20.01 and below. By manipulating the model name parameter during a password change request in the web administrator page, it is possible to trigger a command injection in httpd.

A command injection vulnerability exists in the D-Link DIR-882 Router firmware DIR882A1_FW102B02 within the `prog.cgi` and `rc` binaries. The `sub_432F60` function in `prog.cgi` stores user-supplied `SetSysLogSettings/IPAddress` values in NVRAM via `nvram_safe_set("SysLogRemote_IPAddress", ...)`. These values are later retrieved in the `sub_448DCC` function of `rc` using `nvram_safe_get` and concatenated into a shell command executed via `twsystem()` without any sanitization. An unauthenticated remote attacker can exploit this vulnerability to execute arbitrary commands on the device through specially crafted HTTP requests to the router's web interface.

A command injection vulnerability exists in the D-Link DIR-823G router firmware DIR823G_V1.0.2B05_20181207.bin in the timelycheck and sysconf binaries, which process the /var/system/linux_vlan_reinit file. The vulnerability occurs because content read from this file is only partially validated for a prefix and then formatted using vsnprintf() before being executed with system(), allowing an attacker with write access to /var/system/linux_vlan_reinit to execute arbitrary commands on the device.

A command injection vulnerability exists in the D-Link DIR-823G router firmware DIR823G_V1.0.2B05_20181207.bin in the timelycheck and sysconf binaries, which process the /tmp/new_qos.rule configuration file. The vulnerability occurs because parsed fields from the configuration file are concatenated into command strings and executed via system() without any sanitization. An attacker with write access to /tmp/new_qos.rule can execute arbitrary commands on the device.

The remote administration interface in D-Link DIR-815 devices with firmware before 2.03.B02 allows remote attackers to execute arbitrary commands via vectors related to an "HTTP command injection issue."

A vulnerability was found in D-Link DCS-932L 2.18.01. It has been classified as critical. Affected is the function setSystemAdmin of the file /setSystemAdmin. The manipulation of the argument AdminID leads to os command injection. It is possible to launch the attack remotely. The exploit has been disclosed to the public and may be used. This vulnerability only affects products that are no longer supported by the maintainer.

A vulnerability was found in D-Link DCS-932L 2.18.01. It has been rated as critical. Affected by this issue is the function setSystemWizard/setSystemControl of the file /setSystemWizard. The manipulation of the argument AdminID leads to os command injection. The attack may be launched remotely. The exploit has been disclosed to the public and may be used. This vulnerability only affects products that are no longer supported by the maintainer.

The DI-7400G+ router has a command injection vulnerability, which allows attackers to execute arbitrary commands on the device. The sub_478D28 function in in mng_platform.asp, and sub_4A12DC function in wayos_ac_server.asp of the jhttpd program, with the parameter ac_mng_srv_host.

A vulnerability, which was classified as critical, was found in D-Link DIR-816 1.10CNB05. Affected is the function setipsec_config of the file /goform/setipsec_config. The manipulation of the argument localIP/remoteIP leads to os command injection. It is possible to launch the attack remotely. The exploit has been disclosed to the public and may be used. This vulnerability only affects products that are no longer supported by the maintainer.

D-Link DIR-823G v1.0.2 was found to contain a command injection vulnerability in the function SetNetworkTomographySettings. This vulnerability allows attackers to execute arbitrary commands via a crafted packet.

A weakness has been identified in D-Link DIR-816 1.10CNB05_R1B011D88210. Affected by this vulnerability is the function sub_445E7C of the file /goform/formDMZ.cgi. This manipulation causes command injection. It is possible to initiate the attack remotely. The exploit has been made available to the public and could be used for attacks.

A security flaw has been discovered in D-Link DNS-320 2.06B01. This affects the function delete/rename/copy/move/chmod/chown of the file /cgi-bin/webfile_mgr.cgi. The manipulation results in os command injection. The attack may be performed from remote. The exploit has been released to the public and may be used for attacks.

A weakness has been identified in D-Link DNS-320 2.06B01. This impacts the function cgi_set_host/cgi_set_ntp/cgi_fan_control/cgi_merge_user of the file /cgi-bin/system_mgr.cgi. This manipulation causes os command injection. It is possible to initiate the attack remotely.

A vulnerability was detected in D-Link DIR-816 1.10CNB05_R1B011D88210. This affects the function portForward. Performing a manipulation of the argument ip_address results in command injection. The attack can be initiated remotely. The exploit is now public and may be used.

A vulnerability was identified in D-Link DNS-320 2.06B01. The impacted element is the function cgi_speed/cgi_dhcpd_lease/cgi_ddns/cgi_set_ip/cgi_upnp_del/cgi_dhcpd/cgi_upnp_add/cgi_upnp_edit of the file /cgi-bin/network_mgr.cgi. The manipulation leads to os command injection. The attack is possible to be carried out remotely. The exploit is publicly available and might be used.

A security vulnerability has been detected in D-Link DIR-816 1.10CNB05_R1B011D88210. Affected by this issue is the function sub_445E7C of the file /goform/singlePortForward. Such manipulation of the argument ip_address leads to command injection. It is possible to launch the attack remotely. The exploit has been disclosed publicly and may be used.

A vulnerability was determined in D-Link DIR-822 A_101. The impacted element is the function system of the file /udhcpcd/dhcpd.c of the component udhcpd DHCP Service. This manipulation of the argument Hostname causes command injection. The attack can be initiated remotely. The exploit has been publicly disclosed and may be utilized. This vulnerability only affects products that are no longer supported by the maintainer.

** UNSUPPORTED WHEN ASSIGNED ** A vulnerability, which was classified as critical, was found in D-Link DNS-320L, DNS-325, DNS-327L and DNS-340L up to 20240403. Affected is an unknown function of the file /cgi-bin/nas_sharing.cgi of the component HTTP GET Request Handler. The manipulation of the argument system leads to command injection. It is possible to launch the attack remotely. The exploit has been disclosed to the public and may be used. The identifier of this vulnerability is VDB-259284. NOTE: This vulnerability only affects products that are no longer supported by the maintainer. NOTE: Vendor was contacted early and confirmed immediately that the product is end-of-life. It should be retired and replaced.

A vulnerability was found in D-Link DIR-882 1.01B02. Impacted is the function sprintf of the file prog.cgi of the component HNAP1 SetNetworkSettings Handler. The manipulation of the argument IPAddress results in os command injection. The attack may be performed from remote. The exploit has been made public and could be used. This vulnerability only affects products that are no longer supported by the maintainer.

A vulnerability has been found in D-Link DI-500WF-WT up to 20250511 and classified as critical. Affected by this vulnerability is the function sub_456DE8 of the file /msp_info.htm?flag=cmd of the component /usr/sbin/jhttpd. The manipulation of the argument cmd leads to command injection. The attack can be launched remotely.

A flaw has been found in D-Link DIR-513 1.10. The impacted element is an unknown function of the file /goform/formSysCmd. Executing a manipulation of the argument sysCmd can lead to os command injection. The attack may be launched remotely. The exploit has been published and may be used. This vulnerability only affects products that are no longer supported by the maintainer.

A vulnerability was detected in D-Link DNS-120, DNR-202L, DNS-315L, DNS-320, DNS-320L, DNS-320LW, DNS-321, DNR-322L, DNS-323, DNS-325, DNS-326, DNS-327L, DNR-326, DNS-340L, DNS-343, DNS-345, DNS-726-4, DNS-1100-4, DNS-1200-05 and DNS-1550-04 up to 20260205. Impacted is the function cgi_portforwarding_add/cgi_portforwarding_del/cgi_portforwarding_modify/cgi_portforwarding_add_scan/cgi_dhcpd_lease/cgi_ddns/cgi_ip/cgi_dhcpd of the file /cgi-bin/network_mgr.cgi. The manipulation results in command injection. The attack may be launched remotely. The exploit is now public and may be used.

An issue was discovered on D-Link DIR-818LW devices from 2.05.B03 to 2.06B01 BETA. There is a command injection in HNAP1 SetWanSettings via an XML injection of the value of the IPAddress key.