An unauthenticated command injection vulnerability exists in the D-Link DIR-878A1 router firmware FW101B04.bin. The vulnerability occurs in the 'SetDynamicDNSSettings' functionality, where the 'ServerAddress' and 'Hostname' parameters in prog.cgi are stored in NVRAM and later used by rc to construct system commands executed via twsystem(). An attacker can exploit this vulnerability remotely without authentication by sending a specially crafted HTTP request, leading to arbitrary command execution on the device.

A command injection vulnerability exists in the D-Link DIR-882 Router firmware DIR882A1_FW102B02 within the `prog.cgi` and `librcm.so` binaries. The `sub_4455BC` function in `prog.cgi` stores user-supplied `SetDMZSettings/IPAddress` values in NVRAM via `nvram_safe_set("dmz_ipaddr", ...)`. These values are later retrieved in the `DMZ_run` function of `librcm.so` using `nvram_safe_get` and concatenated into `iptables` shell commands executed via `twsystem()` without any sanitization. An unauthenticated remote attacker can exploit this vulnerability to execute arbitrary commands on the device through specially crafted HTTP requests to the router's web interface.

Hardcoded credentials in the Telnet service in D-Link DIR-605L v2.13B01 and DIR-816L v2.06B01 allow attackers to remotely execute arbitrary commands via firmware analysis.

D-Link DSL-7740C with firmware DSL7740C.V6.TR069.20211230 was discovered to contain a command injection vulnerability via the ping function.

An unauthenticated command injection vulnerability exists in the D-Link DIR-878A1 router firmware FW101B04.bin. The vulnerability occurs in the 'SetNetworkSettings' functionality of prog.cgi, where the 'IPAddress' and 'SubnetMask' parameters are directly concatenated into shell commands executed via system(). An attacker can exploit this vulnerability remotely without authentication by sending a specially crafted HTTP request, leading to arbitrary command execution on the device.

D-Link DIR-816 A2V1.1.0B05 was found to contain a command injection in /goform/delRouting.

A command injection vulnerability exists in the D-Link DIR-882 Router firmware DIR882A1_FW102B02 within the `prog.cgi` and `rc` binaries. The `sub_433188` function in `prog.cgi` stores user-supplied email configuration parameters (`EmailFrom`, `EmailTo`, `SMTPServerAddress`, `SMTPServerPort`, `AccountName`) in NVRAM via `nvram_safe_set`. These values are later retrieved in the `sub_448FDC` function of `rc` using `nvram_safe_get` and concatenated into shell commands executed via `twsystem()` without sanitization. An unauthenticated remote attacker can exploit this vulnerability to execute arbitrary commands on the device through specially crafted HTTP requests to the router's web interface.

An access control issue in the component form2RepeaterSetup.cgi of D-Link 816A2_FWv1.10CNB05_R1B011D88210 allows unauthenticated attackers to set the 2.4G and 5G repeater service of the device via a crafted POST request.

An access control issue in the component form2Wan.cgi of D-Link 816A2_FWv1.10CNB05_R1B011D88210 allows unauthenticated attackers to set the wan service of the device via a crafted POST request.

An access control issue in the component form2WlanBasicSetup.cgi of D-Link 816A2_FWv1.10CNB05_R1B011D88210 allows unauthenticated attackers to set the 2.4G and 5G wlan service of the device via a crafted POST request.

An access control issue in the component form2WlAc.cgi of D-Link 816A2_FWv1.10CNB05_R1B011D88210 allows unauthenticated attackers to set the 2.4G and 5G mac access control list of the device via a crafted POST request.

OS Command injection vulnerability in D-Link C1 2020-02-21. The sub_47F028 function in jhttpd contains a command injection vulnerability via the HTTP parameter "time".

D-Link Go-RT-AC750 GORTAC750_revA_v101b03 & GO-RT-AC750_revB_FWv200b02 is vulnerable to command injection via /htdocs/upnpinc/gena.php.

DLINK - DSL-224 Post-auth RCE. DLINK router version 3.0.8 has an interface where you can configure NTP servers (Network Time Protocol) via jsonrpc API. It is possible to inject a command through this interface that will run with ROOT permissions on the router.

This vulnerability allows network-adjacent attackers to execute arbitrary code on affected installations of D-Link DAP-1860 firmware version 1.04B03 WiFi extenders. Authentication is not required to exploit this vulnerability. The specific flaw exists within the HNAP service, which listens on TCP port 80 by default. When parsing the Authorization request header, the process does not properly validate a user-supplied string before using it to execute a system call. An attacker can leverage this vulnerability to execute code in the context of the device. Was ZDI-CAN-10880.

This vulnerability allows network-adjacent attackers to execute arbitrary code on affected installations of D-Link DVA-2800 and DSL-2888A routers. Authentication is not required to exploit this vulnerability. The specific flaw exists within the dhttpd service, which listens on TCP port 8008 by default. When parsing the path parameter, the process does not properly validate a user-supplied string before using it to execute a system call. An attacker can leverage this vulnerability to execute code in the context of the web server. Was ZDI-CAN-10911.

A vulnerability was detected in D-Link DIR-823x up to 250416. The affected element is an unknown function of the file /goform/diag_ping. Performing manipulation of the argument target_addr results in command injection. Remote exploitation of the attack is possible. The exploit is now public and may be used.

A vulnerability was determined in D-Link DIR-852 1.00CN B09. This issue affects the function ssdpcgi_main of the file htodcs/cgibin of the component Simple Service Discovery Protocol Service. Executing manipulation of the argument ST can lead to command injection. The attack may be performed from remote. The exploit has been publicly disclosed and may be utilized. This vulnerability only affects products that are no longer supported by the maintainer.

A vulnerability was determined in D-Link DIR-823X up to 250416. Affected by this vulnerability is the function sub_415028 of the file /goform/set_static_leases. Executing manipulation of the argument Hostname can lead to command injection. The attack can be launched remotely. The exploit has been publicly disclosed and may be utilized.

A vulnerability was found in D-Link DIR-852 1.00CN B09. This vulnerability affects unknown code of the file /htdocs/cgibin/hedwig.cgi of the component Web Management Interface. Performing manipulation results in command injection. The attack is possible to be carried out remotely. The exploit has been made public and could be used. This vulnerability only affects products that are no longer supported by the maintainer.

A vulnerability was determined in D-Link DIR-823X 240126/240802/250416. Affected by this vulnerability is an unknown functionality of the file /usr/sbin/goahead. This manipulation of the argument port causes command injection. The attack can be initiated remotely. The exploit has been publicly disclosed and may be utilized.

A weakness has been identified in D-Link DIR-823X 240126/240802/250416. The impacted element is the function sub_412E7C of the file /usr/sbin/goahead of the component Environment Variable Handler. This manipulation of the argument terminal_addr/server_ip/server_port causes command injection. The attack can be initiated remotely. The exploit has been made available to the public and could be exploited.

A vulnerability was identified in D-Link DIR-645 105B01. This issue affects the function soapcgi_main of the file /soap.cgi. Such manipulation of the argument service leads to command injection. The attack can be launched remotely. The exploit is publicly available and might be used. This vulnerability only affects products that are no longer supported by the maintainer.

A vulnerability was detected in D-Link DI-7100G C1 24.04.18D1. Affected by this issue is the function set_jhttpd_info. Performing a manipulation of the argument usb_username results in command injection. Remote exploitation of the attack is possible.

A vulnerability was found in D-Link DCS-931L up to 1.13.0. Impacted is the function doSystem of the file /setSystemAdmin. Performing a manipulation of the argument AdminID results in command injection. The attack may be initiated remotely. The exploit has been made public and could be used. This vulnerability only affects products that are no longer supported by the maintainer.

A weakness has been identified in D-Link DIR-823X 250416. This vulnerability affects the function sub_420618 of the file /goform/set_upnp. This manipulation of the argument upnp_enable causes os command injection. Remote exploitation of the attack is possible. The exploit has been made available to the public and could be used for attacks.

A vulnerability has been found in D-Link DWR-M921 1.1.50. This impacts an unknown function of the file /boafrm/formLtefotaUpgradeFibocom. Such manipulation of the argument fota_url leads to command injection. It is possible to launch the attack remotely. The exploit has been disclosed to the public and may be used.

A vulnerability was found in D-Link DCS-931L up to 1.13.0. This affects an unknown part of the file /goform/setSysAdmin. The manipulation of the argument AdminID results in os command injection. The attack can be executed remotely. The exploit has been made public and could be used. This vulnerability only affects products that are no longer supported by the maintainer.

An issue was discovered on D-Link DCS-2530L before 1.06.01 Hotfix and DCS-2670L through 2.02 devices. cgi-bin/ddns_enc.cgi allows authenticated command injection.

A vulnerability has been found in D-Link DIR-823X 250416. This affects the function sub_4211C8 of the file /goform/set_filtering. Such manipulation leads to os command injection. The attack may be launched remotely. The exploit has been disclosed to the public and may be used.

A vulnerability was determined in D-Link DCS-933L up to 1.14.11. This affects an unknown function of the file /setSystemAdmin of the component alphapd. This manipulation of the argument AdminID causes command injection. Remote exploitation of the attack is possible. The exploit has been publicly disclosed and may be utilized. This vulnerability only affects products that are no longer supported by the maintainer.

D-Link DSL-2750B devices before 1.05 allow remote unauthenticated command injection via the login.cgi cli parameter, as exploited in the wild in 2016 through 2022.

A flaw has been found in D-Link DI-7100G C1 24.04.18D1. This affects the function start_proxy_client_email. Executing a manipulation can lead to command injection. The attack can be executed remotely. The exploit has been published and may be used.

A flaw has been found in D-Link DWR-M921 1.1.50. This affects the function sub_419920 of the file /boafrm/formLtefotaUpgradeQuectel. This manipulation of the argument fota_url causes command injection. It is possible to initiate the attack remotely. The exploit has been published and may be used.

D-LINK DIR-806 1200M11AC wireless router DIR806A1_FW100CNb11 is vulnerable to command injection due to lax filtering of HTTP_ST parameters.

D-Link DIR-600 Hardware Version B5, Firmware Version 2.18 was discovered to contain a command injection vulnerability via the ST parameter in the lxmldbc_system() function.

D-LINK DWL-6610 FW_v_4.3.0.8B003C was discovered to contain a command injection vulnerability in the function pcap_download_handler. This vulnerability allows attackers to execute arbitrary commands via the update.device.packet-capture.tftp-file-name parameter.

D-LINK DWL-6610 FW_v_4.3.0.8B003C was discovered to contain a command injection vulnerability in the function sub_2EF50. This vulnerability allows attackers to execute arbitrary commands via the manual-time-string parameter.

A weakness has been identified in D-Link DIR-823X 250416. This impacts an unknown function of the file /goform/set_language. Executing a manipulation of the argument langSelection can lead to os command injection. It is possible to launch the attack remotely. The exploit has been made available to the public and could be used for attacks.

A flaw has been found in D-Link DIR-513 1.10. The impacted element is an unknown function of the file /goform/formSysCmd. Executing a manipulation of the argument sysCmd can lead to os command injection. The attack may be launched remotely. The exploit has been published and may be used. This vulnerability only affects products that are no longer supported by the maintainer.

A weakness has been identified in D-Link DIR-823X 250416. This vulnerability affects the function sub_420688 of the file /goform/set_qos. Executing a manipulation can lead to os command injection. The attack can be executed remotely. The exploit has been made available to the public and could be used for attacks.

A vulnerability has been found in D-Link DIR-615 4.10. This affects an unknown part of the file adv_firewall.php of the component DMZ Host Feature. Such manipulation of the argument dmz_ipaddr  leads to os command injection. The attack can be launched remotely. The exploit has been disclosed to the public and may be used. This vulnerability only affects products that are no longer supported by the maintainer.

D-Link DIR-816 A2 1.10 B05 was discovered to contain a command injection vulnerability via the component /goform/Diagnosis.

D-Link Go-RT-AC750 revA_v101b03 was discovered to contain a command injection vulnerability via the service parameter at hedwig.cgi.

A vulnerability was found in D-Link DIR-615 4.10. This vulnerability affects unknown code of the file adv_routing.php of the component Web Configuration Interface. Performing a manipulation of the argument dest_ip/ submask/ gw results in os command injection. The attack may be initiated remotely. The exploit has been made public and could be used. This vulnerability only affects products that are no longer supported by the maintainer.

A security flaw has been discovered in D-Link DIR-823X 250416. This vulnerability affects unknown code of the file /goform/set_ac_server of the component Web Management Interface. The manipulation of the argument ac_server results in os command injection. The attack can be launched remotely. The exploit has been released to the public and may be used for attacks.

A vulnerability was identified in D-Link DIR-600 up to 2.15WWb02. This vulnerability affects unknown code of the file ssdp.cgi. Such manipulation of the argument HTTP_ST/REMOTE_ADDR/REMOTE_PORT/SERVER_ID leads to command injection. The attack may be launched remotely. The exploit is publicly available and might be used. This vulnerability only affects products that are no longer supported by the maintainer.

A vulnerability was determined in D-Link DIR-823X 250416. Affected by this issue is the function sub_424D20 of the file /goform/set_ipv6. Executing a manipulation can lead to os command injection. It is possible to launch the attack remotely. The exploit has been publicly disclosed and may be utilized.

A security vulnerability has been detected in D-Link DIR-823X 250416. This affects the function sub_4175CC of the file /goform/set_static_route_table. Such manipulation of the argument interface/destip/netmask/gateway/metric leads to os command injection. The attack may be performed from remote. The exploit has been disclosed publicly and may be used.

A vulnerability was determined in D-Link DIR-823X 250416. The affected element is an unknown function of the file /goform/set_password. This manipulation of the argument http_passwd causes os command injection. The attack is possible to be carried out remotely. The exploit has been publicly disclosed and may be utilized.