Varnish Cache 9 before 9.0.1 allows a "workspace overflow" denial of service (daemon panic) after timeout_linger. A malicious client could send an HTTP/1 request, wait long enough until the session releases its worker thread (timeout_linger) and resume traffic before the session is closed (timeout_idle) sending more than one request at once to trigger a pipelining operation between requests. This vulnerability affecting Varnish Cache 9.0.0 emerged from a port of the Varnish Enterprise non-blocking architecture for HTTP/2. New code was needed to adapt to a more recent workspace API that formalizes the pipelining operation. In addition to the workspace change on the Varnish Cache side, other differences created merge conflicts, like partial support for trailers in Varnish Enterprise. The conflict resolution missed one code path configuring pipelining to perform a complete workspace rollback, losing the guarantee that prefetched data would fit inside workspace_client during the transition from one request to the next. This can result in a workspace overflow, triggering a panic and crashing the Varnish server.

Varnish Cache 9 before 9.0.1 and Varnish Enterprise before 6.0.16r11 allows a "workspace overflow" denial of service (daemon panic) for certain amounts of prefetched data. The setup of an HTTP/2 session starts with a speculative HTTP/1 transport, and upon upgrading to h2 the HTTP/1 request is repurposed as stream zero. During the upgrade, a buffer allocation is made to reserve space to send frames to the client. This allocation would split the original workspace, and depending on the amount of prefetched data, the next fetch could perform a pipelining operation that would run out of workspace.

An always-incorrect control flow implementation in the implicit filter terms of Juniper Networks Junos OS and Junos OS Evolved on ACX5800, EX9200 Series, MX10000 Series, MX240, MX480, MX960 devices with affected Trio line cards allows an attacker to exploit an interdependency in the PFE UCODE microcode of the Trio chipset with various line cards to cause packets destined to the devices interfaces to cause a Denial of Service (DoS) condition by looping the packet with an unreachable exit condition ('Infinite Loop'). To break this loop once it begins one side of the affected LT interfaces will need to be disabled. Once disabled, the condition will clear and the disabled LT interface can be reenabled. Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. This issue only affects LT-LT interfaces. Any other interfaces are not affected by this issue. This issue affects the following cards: MPCE Type 3 3D MPC4E 3D 32XGE MPC4E 3D 2CGE+8XGE EX9200 32x10G SFP EX9200-2C-8XS FPC Type 5-3D FPC Type 5-LSR EX9200 4x40G QSFP An Indicator of Compromise (IoC) can be seen by examining the traffic of the LT-LT interfaces for excessive traffic using the following command: monitor interface traffic Before loop impact: Interface: lt-2/0/0, Enabled, Link is Up Encapsulation: Logical-tunnel, Speed: 100000mbps Traffic statistics: Current delta Input bytes: 3759900268942 (1456 bps) [0] <---------- LT interface utilization is low Output bytes: 3759900344309 (1456 bps) [0] <---------- LT interface utilization is low After loop impact: Interface: lt-2/0/0, Enabled, Link is Up Encapsulation: Logical-tunnel, Speed: 100000mbps Traffic statistics: Current delta Input bytes: 3765160313129 (2158268368 bps) [5260044187] <---------- LT interface utilization is very high Output bytes: 3765160399522 (2158266440 bps) [5260055213] <---------- LT interface utilization is very high This issue affects: Juniper Networks Junos OS on ACX5800, EX9200 Series, MX10000 Series, MX240, MX480, MX960. Versions 15.1F6, 16.1R1, and later versions prior to 16.1R7-S8; 17.1 versions prior to 17.1R2-S12; 17.2 versions prior to 17.2R3-S4; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S10, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R2-S7, 18.2R3-S3; 18.3 versions prior to 18.3R1-S7, 18.3R3-S2; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3-S2; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S4, 19.2R2; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S1, 19.4R2. This issue does not affect the MX10001. This issue does not affect Juniper Networks Junos OS versions prior to 15.1F6, 16.1R1. Juniper Networks Junos OS Evolved on ACX5800, EX9200 Series, MX10000 Series, MX240, MX480, MX960 19.4 versions prior to 19.4R2-EVO. This issue does not affect the MX10001.