In the Linux kernel, the following vulnerability has been resolved: PCI: rcar-ep: Fix incorrect variable used when calling devm_request_mem_region() The rcar_pcie_parse_outbound_ranges() uses the devm_request_mem_region() macro to request a needed resource. A string variable that lives on the stack is then used to store a dynamically computed resource name, which is then passed on as one of the macro arguments. This can lead to undefined behavior. Depending on the current contents of the memory, the manifestations of errors may vary. One possible output may be as follows: $ cat /proc/iomem 30000000-37ffffff : 38000000-3fffffff : Sometimes, garbage may appear after the colon. In very rare cases, if no NULL-terminator is found in memory, the system might crash because the string iterator will overrun which can lead to access of unmapped memory above the stack. Thus, fix this by replacing outbound_name with the name of the previously requested resource. With the changes applied, the output will be as follows: $ cat /proc/iomem 30000000-37ffffff : memory2 38000000-3fffffff : memory3 [kwilczynski: commit log]

In the Linux kernel, the following vulnerability has been resolved: staging: gpib: Fix Oops after disconnect in ni_usb If the usb dongle is disconnected subsequent calls to the driver cause a NULL dereference Oops as the bus_interface is set to NULL on disconnect. This problem was introduced by setting usb_dev from the bus_interface for dev_xxx messages. Previously bus_interface was checked for NULL only in the the functions directly calling usb_fill_bulk_urb or usb_control_msg. Check for valid bus_interface on all interface entry points and return -ENODEV if it is NULL.

In the Linux kernel, the following vulnerability has been resolved: net: ethtool: netlink: Allow NULL nlattrs when getting a phy_device ethnl_req_get_phydev() is used to lookup a phy_device, in the case an ethtool netlink command targets a specific phydev within a netdev's topology. It takes as a parameter a const struct nlattr *header that's used for error handling : if (!phydev) { NL_SET_ERR_MSG_ATTR(extack, header, "no phy matching phyindex"); return ERR_PTR(-ENODEV); } In the notify path after a ->set operation however, there's no request attributes available. The typical callsite for the above function looks like: phydev = ethnl_req_get_phydev(req_base, tb[ETHTOOL_A_XXX_HEADER], info->extack); So, when tb is NULL (such as in the ethnl notify path), we have a nice crash. It turns out that there's only the PLCA command that is in that case, as the other phydev-specific commands don't have a notification. This commit fixes the crash by passing the cmd index and the nlattr array separately, allowing NULL-checking it directly inside the helper.

In the Linux kernel, the following vulnerability has been resolved: w1: fix NULL pointer dereference in probe The w1_uart_probe() function calls w1_uart_serdev_open() (which includes devm_serdev_device_open()) before setting the client ops via serdev_device_set_client_ops(). This ordering can trigger a NULL pointer dereference in the serdev controller's receive_buf handler, as it assumes serdev->ops is valid when SERPORT_ACTIVE is set. This is similar to the issue fixed in commit 5e700b384ec1 ("platform/chrome: cros_ec_uart: properly fix race condition") where devm_serdev_device_open() was called before fully initializing the device. Fix the race by ensuring client ops are set before enabling the port via w1_uart_serdev_open().

In the Linux kernel, the following vulnerability has been resolved: pinctrl: nuvoton: npcm8xx: Add NULL check in npcm8xx_gpio_fw devm_kasprintf() calls can return null pointers on failure. But the return values were not checked in npcm8xx_gpio_fw(). Add NULL check in npcm8xx_gpio_fw(), to handle kernel NULL pointer dereference error.

In the Linux kernel, the following vulnerability has been resolved: ASoC: SOF: ipc4-topology: Harden loops for looking up ALH copiers Other, non DAI copier widgets could have the same stream name (sname) as the ALH copier and in that case the copier->data is NULL, no alh_data is attached, which could lead to NULL pointer dereference. We could check for this NULL pointer in sof_ipc4_prepare_copier_module() and avoid the crash, but a similar loop in sof_ipc4_widget_setup_comp_dai() will miscalculate the ALH device count, causing broken audio. The correct fix is to harden the matching logic by making sure that the 1. widget is a DAI widget - so dai = w->private is valid 2. the dai (and thus the copier) is ALH copier

In the Linux kernel, the following vulnerability has been resolved: watch_queue: Fix NULL dereference in error cleanup In watch_queue_set_size(), the error cleanup code doesn't take account of the fact that __free_page() can't handle a NULL pointer when trying to free up buffer pages that did get allocated. Fix this by only calling __free_page() on the pages actually allocated. Without the fix, this can lead to something like the following: BUG: KASAN: null-ptr-deref in __free_pages+0x1f/0x1b0 mm/page_alloc.c:5473 Read of size 4 at addr 0000000000000034 by task syz-executor168/3599 ... Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 __kasan_report mm/kasan/report.c:446 [inline] kasan_report.cold+0x66/0xdf mm/kasan/report.c:459 check_region_inline mm/kasan/generic.c:183 [inline] kasan_check_range+0x13d/0x180 mm/kasan/generic.c:189 instrument_atomic_read include/linux/instrumented.h:71 [inline] atomic_read include/linux/atomic/atomic-instrumented.h:27 [inline] page_ref_count include/linux/page_ref.h:67 [inline] put_page_testzero include/linux/mm.h:717 [inline] __free_pages+0x1f/0x1b0 mm/page_alloc.c:5473 watch_queue_set_size+0x499/0x630 kernel/watch_queue.c:275 pipe_ioctl+0xac/0x2b0 fs/pipe.c:632 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:874 [inline] __se_sys_ioctl fs/ioctl.c:860 [inline] __x64_sys_ioctl+0x193/0x200 fs/ioctl.c:860 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x44/0xae

In the Linux kernel, the following vulnerability has been resolved: can: etas_es58x: fix potential NULL pointer dereference on udev->serial The driver assumed that es58x_dev->udev->serial could never be NULL. While this is true on commercially available devices, an attacker could spoof the device identity providing a NULL USB serial number. That would trigger a NULL pointer dereference. Add a check on es58x_dev->udev->serial before accessing it.

In the Linux kernel, the following vulnerability has been resolved: caif_virtio: fix wrong pointer check in cfv_probe() del_vqs() frees virtqueues, therefore cfv->vq_tx pointer should be checked for NULL before calling it, not cfv->vdev. Also the current implementation is redundant because the pointer cfv->vdev is dereferenced before it is checked for NULL. Fix this by checking cfv->vq_tx for NULL instead of cfv->vdev before calling del_vqs().

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: fix missing .is_two_pixels_per_container Starting from 6.11, AMDGPU driver, while being loaded with amdgpu.dc=1, due to lack of .is_two_pixels_per_container function in dce60_tg_funcs, causes a NULL pointer dereference on PCs with old GPUs, such as R9 280X. So this fix adds missing .is_two_pixels_per_container to dce60_tg_funcs. (cherry picked from commit bd4b125eb949785c6f8a53b0494e32795421209d)

In the Linux kernel, the following vulnerability has been resolved: sched_ext: Validate prev_cpu in scx_bpf_select_cpu_dfl() If a BPF scheduler provides an invalid CPU (outside the nr_cpu_ids range) as prev_cpu to scx_bpf_select_cpu_dfl() it can cause a kernel crash. To prevent this, validate prev_cpu in scx_bpf_select_cpu_dfl() and trigger an scx error if an invalid CPU is specified.

In the Linux kernel, the following vulnerability has been resolved: netlabel: Fix NULL pointer exception caused by CALIPSO on IPv4 sockets When calling netlbl_conn_setattr(), addr->sa_family is used to determine the function behavior. If sk is an IPv4 socket, but the connect function is called with an IPv6 address, the function calipso_sock_setattr() is triggered. Inside this function, the following code is executed: sk_fullsock(__sk) ? inet_sk(__sk)->pinet6 : NULL; Since sk is an IPv4 socket, pinet6 is NULL, leading to a null pointer dereference. This patch fixes the issue by checking if inet6_sk(sk) returns a NULL pointer before accessing pinet6.

In the Linux kernel, the following vulnerability has been resolved: arm: pgtable: fix NULL pointer dereference issue When update_mmu_cache_range() is called by update_mmu_cache(), the vmf parameter is NULL, which will cause a NULL pointer dereference issue in adjust_pte(): Unable to handle kernel NULL pointer dereference at virtual address 00000030 when read Hardware name: Atmel AT91SAM9 PC is at update_mmu_cache_range+0x1e0/0x278 LR is at pte_offset_map_rw_nolock+0x18/0x2c Call trace: update_mmu_cache_range from remove_migration_pte+0x29c/0x2ec remove_migration_pte from rmap_walk_file+0xcc/0x130 rmap_walk_file from remove_migration_ptes+0x90/0xa4 remove_migration_ptes from migrate_pages_batch+0x6d4/0x858 migrate_pages_batch from migrate_pages+0x188/0x488 migrate_pages from compact_zone+0x56c/0x954 compact_zone from compact_node+0x90/0xf0 compact_node from kcompactd+0x1d4/0x204 kcompactd from kthread+0x120/0x12c kthread from ret_from_fork+0x14/0x38 Exception stack(0xc0d8bfb0 to 0xc0d8bff8) To fix it, do not rely on whether 'ptl' is equal to decide whether to hold the pte lock, but decide it by whether CONFIG_SPLIT_PTE_PTLOCKS is enabled. In addition, if two vmas map to the same PTE page, there is no need to hold the pte lock again, otherwise a deadlock will occur. Just add the need_lock parameter to let adjust_pte() know this information.

In the Linux kernel, the following vulnerability has been resolved: sched: address a potential NULL pointer dereference in the GRED scheduler. If kzalloc in gred_init returns a NULL pointer, the code follows the error handling path, invoking gred_destroy. This, in turn, calls gred_offload, where memset could receive a NULL pointer as input, potentially leading to a kernel crash. When table->opt is NULL in gred_init(), gred_change_table_def() is not called yet, so it is not necessary to call ->ndo_setup_tc() in gred_offload().

In the Linux kernel, the following vulnerability has been resolved: PCI: Fix NULL dereference in SR-IOV VF creation error path Clean up when virtfn setup fails to prevent NULL pointer dereference during device removal. The kernel oops below occurred due to incorrect error handling flow when pci_setup_device() fails. Add pci_iov_scan_device(), which handles virtfn allocation and setup and cleans up if pci_setup_device() fails, so pci_iov_add_virtfn() doesn't need to call pci_stop_and_remove_bus_device(). This prevents accessing partially initialized virtfn devices during removal. BUG: kernel NULL pointer dereference, address: 00000000000000d0 RIP: 0010:device_del+0x3d/0x3d0 Call Trace: pci_remove_bus_device+0x7c/0x100 pci_iov_add_virtfn+0xfa/0x200 sriov_enable+0x208/0x420 mlx5_core_sriov_configure+0x6a/0x160 [mlx5_core] sriov_numvfs_store+0xae/0x1a0 [bhelgaas: commit log, return ERR_PTR(-ENOMEM) directly]

In the Linux kernel, the following vulnerability has been resolved: sctp: sysctl: auth_enable: avoid using current->nsproxy As mentioned in a previous commit of this series, using the 'net' structure via 'current' is not recommended for different reasons: - Inconsistency: getting info from the reader's/writer's netns vs only from the opener's netns. - current->nsproxy can be NULL in some cases, resulting in an 'Oops' (null-ptr-deref), e.g. when the current task is exiting, as spotted by syzbot [1] using acct(2). The 'net' structure can be obtained from the table->data using container_of(). Note that table->data could also be used directly, but that would increase the size of this fix, while 'sctp.ctl_sock' still needs to be retrieved from 'net' structure.

In the Linux kernel, the following vulnerability has been resolved: net: ethernet: ti: am65-cpsw: fix freeing IRQ in am65_cpsw_nuss_remove_tx_chns() When getting the IRQ we use k3_udma_glue_tx_get_irq() which returns negative error value on error. So not NULL check is not sufficient to deteremine if IRQ is valid. Check that IRQ is greater then zero to ensure it is valid. There is no issue at probe time but at runtime user can invoke .set_channels which results in the following call chain. am65_cpsw_set_channels() am65_cpsw_nuss_update_tx_rx_chns() am65_cpsw_nuss_remove_tx_chns() am65_cpsw_nuss_init_tx_chns() At this point if am65_cpsw_nuss_init_tx_chns() fails due to k3_udma_glue_tx_get_irq() then tx_chn->irq will be set to a negative value. Then, at subsequent .set_channels with higher channel count we will attempt to free an invalid IRQ in am65_cpsw_nuss_remove_tx_chns() leading to a kernel warning. The issue is present in the original commit that introduced this driver, although there, am65_cpsw_nuss_update_tx_rx_chns() existed as am65_cpsw_nuss_update_tx_chns().

In the Linux kernel, the following vulnerability has been resolved: RDMA/mlx5: Fix mlx5_poll_one() cur_qp update flow When cur_qp isn't NULL, in order to avoid fetching the QP from the radix tree again we check if the next cqe QP is identical to the one we already have. The bug however is that we are checking if the QP is identical by checking the QP number inside the CQE against the QP number inside the mlx5_ib_qp, but that's wrong since the QP number from the CQE is from FW so it should be matched against mlx5_core_qp which is our FW QP number. Otherwise we could use the wrong QP when handling a CQE which could cause the kernel trace below. This issue is mainly noticeable over QPs 0 & 1, since for now they are the only QPs in our driver whereas the QP number inside mlx5_ib_qp doesn't match the QP number inside mlx5_core_qp. BUG: kernel NULL pointer dereference, address: 0000000000000012 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: Oops: 0000 [#1] SMP CPU: 0 UID: 0 PID: 7927 Comm: kworker/u62:1 Not tainted 6.14.0-rc3+ #189 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014 Workqueue: ib-comp-unb-wq ib_cq_poll_work [ib_core] RIP: 0010:mlx5_ib_poll_cq+0x4c7/0xd90 [mlx5_ib] Code: 03 00 00 8d 58 ff 21 cb 66 39 d3 74 39 48 c7 c7 3c 89 6e a0 0f b7 db e8 b7 d2 b3 e0 49 8b 86 60 03 00 00 48 c7 c7 4a 89 6e a0 <0f> b7 5c 98 02 e8 9f d2 b3 e0 41 0f b7 86 78 03 00 00 83 e8 01 21 RSP: 0018:ffff88810511bd60 EFLAGS: 00010046 RAX: 0000000000000010 RBX: 0000000000000000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffff88885fa1b3c0 RDI: ffffffffa06e894a RBP: 00000000000000b0 R08: 0000000000000000 R09: ffff88810511bc10 R10: 0000000000000001 R11: 0000000000000001 R12: ffff88810d593000 R13: ffff88810e579108 R14: ffff888105146000 R15: 00000000000000b0 FS: 0000000000000000(0000) GS:ffff88885fa00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000012 CR3: 00000001077e6001 CR4: 0000000000370eb0 Call Trace: <TASK> ? __die+0x20/0x60 ? page_fault_oops+0x150/0x3e0 ? exc_page_fault+0x74/0x130 ? asm_exc_page_fault+0x22/0x30 ? mlx5_ib_poll_cq+0x4c7/0xd90 [mlx5_ib] __ib_process_cq+0x5a/0x150 [ib_core] ib_cq_poll_work+0x31/0x90 [ib_core] process_one_work+0x169/0x320 worker_thread+0x288/0x3a0 ? work_busy+0xb0/0xb0 kthread+0xd7/0x1f0 ? kthreads_online_cpu+0x130/0x130 ? kthreads_online_cpu+0x130/0x130 ret_from_fork+0x2d/0x50 ? kthreads_online_cpu+0x130/0x130 ret_from_fork_asm+0x11/0x20 </TASK>

In the Linux kernel, the following vulnerability has been resolved: regulator: dummy: force synchronous probing Sometimes I get a NULL pointer dereference at boot time in kobject_get() with the following call stack: anatop_regulator_probe() devm_regulator_register() regulator_register() regulator_resolve_supply() kobject_get() By placing some extra BUG_ON() statements I could verify that this is raised because probing of the 'dummy' regulator driver is not completed ('dummy_regulator_rdev' is still NULL). In the JTAG debugger I can see that dummy_regulator_probe() and anatop_regulator_probe() can be run by different kernel threads (kworker/u4:*). I haven't further investigated whether this can be changed or if there are other possibilities to force synchronization between these two probe routines. On the other hand I don't expect much boot time penalty by probing the 'dummy' regulator synchronously.

In the Linux kernel, the following vulnerability has been resolved: ptp: Ensure info->enable callback is always set The ioctl and sysfs handlers unconditionally call the ->enable callback. Not all drivers implement that callback, leading to NULL dereferences. Example of affected drivers: ptp_s390.c, ptp_vclock.c and ptp_mock.c. Instead use a dummy callback if no better was specified by the driver.

In the Linux kernel, the following vulnerability has been resolved: mptcp: sysctl: blackhole timeout: avoid using current->nsproxy As mentioned in the previous commit, using the 'net' structure via 'current' is not recommended for different reasons: - Inconsistency: getting info from the reader's/writer's netns vs only from the opener's netns. - current->nsproxy can be NULL in some cases, resulting in an 'Oops' (null-ptr-deref), e.g. when the current task is exiting, as spotted by syzbot [1] using acct(2). The 'pernet' structure can be obtained from the table->data using container_of().

In the Linux kernel, the following vulnerability has been resolved: nfp: bpf: Add check for nfp_app_ctrl_msg_alloc() Add check for the return value of nfp_app_ctrl_msg_alloc() in nfp_bpf_cmsg_alloc() to prevent null pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: gpiolib: Fix crash on error in gpiochip_get_ngpios() The gpiochip_get_ngpios() uses chip_*() macros to print messages. However these macros rely on gpiodev to be initialised and set, which is not the case when called via bgpio_init(). In such a case the printing messages will crash on NULL pointer dereference. Replace chip_*() macros by the respective dev_*() ones to avoid such crash.

In the Linux kernel, the following vulnerability has been resolved: net: fix NULL pointer dereference in l3mdev_l3_rcv When delete l3s ipvlan: ip link del link eth0 ipvlan1 type ipvlan mode l3s This may cause a null pointer dereference: Call trace: ip_rcv_finish+0x48/0xd0 ip_rcv+0x5c/0x100 __netif_receive_skb_one_core+0x64/0xb0 __netif_receive_skb+0x20/0x80 process_backlog+0xb4/0x204 napi_poll+0xe8/0x294 net_rx_action+0xd8/0x22c __do_softirq+0x12c/0x354 This is because l3mdev_l3_rcv() visit dev->l3mdev_ops after ipvlan_l3s_unregister() assign the dev->l3mdev_ops to NULL. The process like this: (CPU1) | (CPU2) l3mdev_l3_rcv() | check dev->priv_flags: | master = skb->dev; | | | ipvlan_l3s_unregister() | set dev->priv_flags | dev->l3mdev_ops = NULL; | visit master->l3mdev_ops | To avoid this by do not set dev->l3mdev_ops when unregister l3s ipvlan.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: handle errors in mlx5_chains_create_table() In mlx5_chains_create_table(), the return value of mlx5_get_fdb_sub_ns() and mlx5_get_flow_namespace() must be checked to prevent NULL pointer dereferences. If either function fails, the function should log error message with mlx5_core_warn() and return error pointer.

In the Linux kernel, the following vulnerability has been resolved: net/sched: cls_api: fix error handling causing NULL dereference tcf_exts_miss_cookie_base_alloc() calls xa_alloc_cyclic() which can return 1 if the allocation succeeded after wrapping. This was treated as an error, with value 1 returned to caller tcf_exts_init_ex() which sets exts->actions to NULL and returns 1 to caller fl_change(). fl_change() treats err == 1 as success, calling tcf_exts_validate_ex() which calls tcf_action_init() with exts->actions as argument, where it is dereferenced. Example trace: BUG: kernel NULL pointer dereference, address: 0000000000000000 CPU: 114 PID: 16151 Comm: handler114 Kdump: loaded Not tainted 5.14.0-503.16.1.el9_5.x86_64 #1 RIP: 0010:tcf_action_init+0x1f8/0x2c0 Call Trace: tcf_action_init+0x1f8/0x2c0 tcf_exts_validate_ex+0x175/0x190 fl_change+0x537/0x1120 [cls_flower]

In the Linux kernel, the following vulnerability has been resolved: sctp: sysctl: cookie_hmac_alg: avoid using current->nsproxy As mentioned in a previous commit of this series, using the 'net' structure via 'current' is not recommended for different reasons: - Inconsistency: getting info from the reader's/writer's netns vs only from the opener's netns. - current->nsproxy can be NULL in some cases, resulting in an 'Oops' (null-ptr-deref), e.g. when the current task is exiting, as spotted by syzbot [1] using acct(2). The 'net' structure can be obtained from the table->data using container_of(). Note that table->data could also be used directly, as this is the only member needed from the 'net' structure, but that would increase the size of this fix, to use '*data' everywhere 'net->sctp.sctp_hmac_alg' is used.

In the Linux kernel, the following vulnerability has been resolved: ASoC: SOF: stream-ipc: Check for cstream nullity in sof_ipc_msg_data() The nullity of sps->cstream should be checked similarly as it is done in sof_set_stream_data_offset() function. Assuming that it is not NULL if sps->stream is NULL is incorrect and can lead to NULL pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: HID: steam: Prevent NULL pointer dereference in steam_{recv,send}_report It is possible for a malicious device to forgo submitting a Feature Report. The HID Steam driver presently makes no prevision for this and de-references the 'struct hid_report' pointer obtained from the HID devices without first checking its validity. Let's change that.

In the Linux kernel, the following vulnerability has been resolved: USB: serial: quatech2: fix null-ptr-deref in qt2_process_read_urb() This patch addresses a null-ptr-deref in qt2_process_read_urb() due to an incorrect bounds check in the following: if (newport > serial->num_ports) { dev_err(&port->dev, "%s - port change to invalid port: %i\n", __func__, newport); break; } The condition doesn't account for the valid range of the serial->port buffer, which is from 0 to serial->num_ports - 1. When newport is equal to serial->num_ports, the assignment of "port" in the following code is out-of-bounds and NULL: serial_priv->current_port = newport; port = serial->port[serial_priv->current_port]; The fix checks if newport is greater than or equal to serial->num_ports indicating it is out-of-bounds.

In the Linux kernel, the following vulnerability has been resolved: scsi: qla1280: Fix kernel oops when debug level > 2 A null dereference or oops exception will eventually occur when qla1280.c driver is compiled with DEBUG_QLA1280 enabled and ql_debug_level > 2. I think its clear from the code that the intention here is sg_dma_len(s) not length of sg_next(s) when printing the debug info.

In the Linux kernel, the following vulnerability has been resolved: sctp: sysctl: udp_port: avoid using current->nsproxy As mentioned in a previous commit of this series, using the 'net' structure via 'current' is not recommended for different reasons: - Inconsistency: getting info from the reader's/writer's netns vs only from the opener's netns. - current->nsproxy can be NULL in some cases, resulting in an 'Oops' (null-ptr-deref), e.g. when the current task is exiting, as spotted by syzbot [1] using acct(2). The 'net' structure can be obtained from the table->data using container_of(). Note that table->data could also be used directly, but that would increase the size of this fix, while 'sctp.ctl_sock' still needs to be retrieved from 'net' structure.

In the Linux kernel, the following vulnerability has been resolved: drm/amdkfd: Fix NULL Pointer Dereference in KFD queue Through KFD IOCTL Fuzzing we encountered a NULL pointer derefrence when calling kfd_queue_acquire_buffers. (cherry picked from commit 049e5bf3c8406f87c3d8e1958e0a16804fa1d530)

In the Linux kernel, the following vulnerability has been resolved: usb: renesas_usbhs: Flush the notify_hotplug_work When performing continuous unbind/bind operations on the USB drivers available on the Renesas RZ/G2L SoC, a kernel crash with the message "Unable to handle kernel NULL pointer dereference at virtual address" may occur. This issue points to the usbhsc_notify_hotplug() function. Flush the delayed work to avoid its execution when driver resources are unavailable.

In the Linux kernel, the following vulnerability has been resolved: xfrm: delete intermediate secpath entry in packet offload mode Packets handled by hardware have added secpath as a way to inform XFRM core code that this path was already handled. That secpath is not needed at all after policy is checked and it is removed later in the stack. However, in the case of IP forwarding is enabled (/proc/sys/net/ipv4/ip_forward), that secpath is not removed and packets which already were handled are reentered to the driver TX path with xfrm_offload set. The following kernel panic is observed in mlx5 in such case: mlx5_core 0000:04:00.0 enp4s0f0np0: Link up mlx5_core 0000:04:00.1 enp4s0f1np1: Link up Initializing XFRM netlink socket IPsec XFRM device driver BUG: kernel NULL pointer dereference, address: 0000000000000000 #PF: supervisor instruction fetch in kernel mode #PF: error_code(0x0010) - not-present page PGD 0 P4D 0 Oops: Oops: 0010 [#1] PREEMPT SMP CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.13.0-rc1-alex #3 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-1ubuntu1.1 04/01/2014 RIP: 0010:0x0 Code: Unable to access opcode bytes at 0xffffffffffffffd6. RSP: 0018:ffffb87380003800 EFLAGS: 00010206 RAX: ffff8df004e02600 RBX: ffffb873800038d8 RCX: 00000000ffff98cf RDX: ffff8df00733e108 RSI: ffff8df00521fb80 RDI: ffff8df001661f00 RBP: ffffb87380003850 R08: ffff8df013980000 R09: 0000000000000010 R10: 0000000000000002 R11: 0000000000000002 R12: ffff8df001661f00 R13: ffff8df00521fb80 R14: ffff8df00733e108 R15: ffff8df011faf04e FS: 0000000000000000(0000) GS:ffff8df46b800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffffffffffd6 CR3: 0000000106384000 CR4: 0000000000350ef0 Call Trace: <IRQ> ? show_regs+0x63/0x70 ? __die_body+0x20/0x60 ? __die+0x2b/0x40 ? page_fault_oops+0x15c/0x550 ? do_user_addr_fault+0x3ed/0x870 ? exc_page_fault+0x7f/0x190 ? asm_exc_page_fault+0x27/0x30 mlx5e_ipsec_handle_tx_skb+0xe7/0x2f0 [mlx5_core] mlx5e_xmit+0x58e/0x1980 [mlx5_core] ? __fib_lookup+0x6a/0xb0 dev_hard_start_xmit+0x82/0x1d0 sch_direct_xmit+0xfe/0x390 __dev_queue_xmit+0x6d8/0xee0 ? __fib_lookup+0x6a/0xb0 ? internal_add_timer+0x48/0x70 ? mod_timer+0xe2/0x2b0 neigh_resolve_output+0x115/0x1b0 __neigh_update+0x26a/0xc50 neigh_update+0x14/0x20 arp_process+0x2cb/0x8e0 ? __napi_build_skb+0x5e/0x70 arp_rcv+0x11e/0x1c0 ? dev_gro_receive+0x574/0x820 __netif_receive_skb_list_core+0x1cf/0x1f0 netif_receive_skb_list_internal+0x183/0x2a0 napi_complete_done+0x76/0x1c0 mlx5e_napi_poll+0x234/0x7a0 [mlx5_core] __napi_poll+0x2d/0x1f0 net_rx_action+0x1a6/0x370 ? atomic_notifier_call_chain+0x3b/0x50 ? irq_int_handler+0x15/0x20 [mlx5_core] handle_softirqs+0xb9/0x2f0 ? handle_irq_event+0x44/0x60 irq_exit_rcu+0xdb/0x100 common_interrupt+0x98/0xc0 </IRQ> <TASK> asm_common_interrupt+0x27/0x40 RIP: 0010:pv_native_safe_halt+0xb/0x10 Code: 09 c3 66 66 2e 0f 1f 84 00 00 00 00 00 66 90 0f 22 0f 1f 84 00 00 00 00 00 90 eb 07 0f 00 2d 7f e9 36 00 fb 40 00 83 ff 07 77 21 89 ff ff 24 fd 88 3d a1 bd 0f 21 f8 RSP: 0018:ffffffffbe603de8 EFLAGS: 00000202 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000f92f46680 RDX: 0000000000000037 RSI: 00000000ffffffff RDI: 00000000000518d4 RBP: ffffffffbe603df0 R08: 000000cd42e4dffb R09: ffffffffbe603d70 R10: 0000004d80d62680 R11: 0000000000000001 R12: ffffffffbe60bf40 R13: 0000000000000000 R14: 0000000000000000 R15: ffffffffbe60aff8 ? default_idle+0x9/0x20 arch_cpu_idle+0x9/0x10 default_idle_call+0x29/0xf0 do_idle+0x1f2/0x240 cpu_startup_entry+0x2c/0x30 rest_init+0xe7/0x100 start_kernel+0x76b/0xb90 x86_64_start_reservations+0x18/0x30 x86_64_start_kernel+0xc0/0x110 ? setup_ghcb+0xe/0x130 common_startup_64+0x13e/0x141 </TASK> Modules linked in: esp4_offload esp4 xfrm_interface xfrm6_tunnel tunnel4 tunnel6 xfrm_user xfrm_algo binf ---truncated---

In the Linux kernel, the following vulnerability has been resolved: vsock: prevent null-ptr-deref in vsock_*[has_data|has_space] Recent reports have shown how we sometimes call vsock_*_has_data() when a vsock socket has been de-assigned from a transport (see attached links), but we shouldn't. Previous commits should have solved the real problems, but we may have more in the future, so to avoid null-ptr-deref, we can return 0 (no space, no data available) but with a warning. This way the code should continue to run in a nearly consistent state and have a warning that allows us to debug future problems.

In the Linux kernel, the following vulnerability has been resolved: mptcp: sysctl: sched: avoid using current->nsproxy Using the 'net' structure via 'current' is not recommended for different reasons. First, if the goal is to use it to read or write per-netns data, this is inconsistent with how the "generic" sysctl entries are doing: directly by only using pointers set to the table entry, e.g. table->data. Linked to that, the per-netns data should always be obtained from the table linked to the netns it had been created for, which may not coincide with the reader's or writer's netns. Another reason is that access to current->nsproxy->netns can oops if attempted when current->nsproxy had been dropped when the current task is exiting. This is what syzbot found, when using acct(2): Oops: general protection fault, probably for non-canonical address 0xdffffc0000000005: 0000 [#1] PREEMPT SMP KASAN PTI KASAN: null-ptr-deref in range [0x0000000000000028-0x000000000000002f] CPU: 1 UID: 0 PID: 5924 Comm: syz-executor Not tainted 6.13.0-rc5-syzkaller-00004-gccb98ccef0e5 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 RIP: 0010:proc_scheduler+0xc6/0x3c0 net/mptcp/ctrl.c:125 Code: 03 42 80 3c 38 00 0f 85 fe 02 00 00 4d 8b a4 24 08 09 00 00 48 b8 00 00 00 00 00 fc ff df 49 8d 7c 24 28 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 cc 02 00 00 4d 8b 7c 24 28 48 8d 84 24 c8 00 00 RSP: 0018:ffffc900034774e8 EFLAGS: 00010206 RAX: dffffc0000000000 RBX: 1ffff9200068ee9e RCX: ffffc90003477620 RDX: 0000000000000005 RSI: ffffffff8b08f91e RDI: 0000000000000028 RBP: 0000000000000001 R08: ffffc90003477710 R09: 0000000000000040 R10: 0000000000000040 R11: 00000000726f7475 R12: 0000000000000000 R13: ffffc90003477620 R14: ffffc90003477710 R15: dffffc0000000000 FS: 0000000000000000(0000) GS:ffff8880b8700000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fee3cd452d8 CR3: 000000007d116000 CR4: 00000000003526f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> proc_sys_call_handler+0x403/0x5d0 fs/proc/proc_sysctl.c:601 __kernel_write_iter+0x318/0xa80 fs/read_write.c:612 __kernel_write+0xf6/0x140 fs/read_write.c:632 do_acct_process+0xcb0/0x14a0 kernel/acct.c:539 acct_pin_kill+0x2d/0x100 kernel/acct.c:192 pin_kill+0x194/0x7c0 fs/fs_pin.c:44 mnt_pin_kill+0x61/0x1e0 fs/fs_pin.c:81 cleanup_mnt+0x3ac/0x450 fs/namespace.c:1366 task_work_run+0x14e/0x250 kernel/task_work.c:239 exit_task_work include/linux/task_work.h:43 [inline] do_exit+0xad8/0x2d70 kernel/exit.c:938 do_group_exit+0xd3/0x2a0 kernel/exit.c:1087 get_signal+0x2576/0x2610 kernel/signal.c:3017 arch_do_signal_or_restart+0x90/0x7e0 arch/x86/kernel/signal.c:337 exit_to_user_mode_loop kernel/entry/common.c:111 [inline] exit_to_user_mode_prepare include/linux/entry-common.h:329 [inline] __syscall_exit_to_user_mode_work kernel/entry/common.c:207 [inline] syscall_exit_to_user_mode+0x150/0x2a0 kernel/entry/common.c:218 do_syscall_64+0xda/0x250 arch/x86/entry/common.c:89 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7fee3cb87a6a Code: Unable to access opcode bytes at 0x7fee3cb87a40. RSP: 002b:00007fffcccac688 EFLAGS: 00000202 ORIG_RAX: 0000000000000037 RAX: 0000000000000000 RBX: 00007fffcccac710 RCX: 00007fee3cb87a6a RDX: 0000000000000041 RSI: 0000000000000000 RDI: 0000000000000003 RBP: 0000000000000003 R08: 00007fffcccac6ac R09: 00007fffcccacac7 R10: 00007fffcccac710 R11: 0000000000000202 R12: 00007fee3cd49500 R13: 00007fffcccac6ac R14: 0000000000000000 R15: 00007fee3cd4b000 </TASK> Modules linked in: ---[ end trace 0000000000000000 ]--- RIP: 0010:proc_scheduler+0xc6/0x3c0 net/mptcp/ctrl.c:125 Code: 03 42 80 3c 38 00 0f 85 fe 02 00 00 4d 8b a4 24 08 09 00 00 48 b8 00 00 00 00 00 fc ---truncated---

In the Linux kernel, the following vulnerability has been resolved: btrfs: avoid NULL pointer dereference if no valid extent tree [BUG] Syzbot reported a crash with the following call trace: BTRFS info (device loop0): scrub: started on devid 1 BUG: kernel NULL pointer dereference, address: 0000000000000208 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 106e70067 P4D 106e70067 PUD 107143067 PMD 0 Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 1 UID: 0 PID: 689 Comm: repro Kdump: loaded Tainted: G O 6.13.0-rc4-custom+ #206 Tainted: [O]=OOT_MODULE Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS unknown 02/02/2022 RIP: 0010:find_first_extent_item+0x26/0x1f0 [btrfs] Call Trace: <TASK> scrub_find_fill_first_stripe+0x13d/0x3b0 [btrfs] scrub_simple_mirror+0x175/0x260 [btrfs] scrub_stripe+0x5d4/0x6c0 [btrfs] scrub_chunk+0xbb/0x170 [btrfs] scrub_enumerate_chunks+0x2f4/0x5f0 [btrfs] btrfs_scrub_dev+0x240/0x600 [btrfs] btrfs_ioctl+0x1dc8/0x2fa0 [btrfs] ? do_sys_openat2+0xa5/0xf0 __x64_sys_ioctl+0x97/0xc0 do_syscall_64+0x4f/0x120 entry_SYSCALL_64_after_hwframe+0x76/0x7e </TASK> [CAUSE] The reproducer is using a corrupted image where extent tree root is corrupted, thus forcing to use "rescue=all,ro" mount option to mount the image. Then it triggered a scrub, but since scrub relies on extent tree to find where the data/metadata extents are, scrub_find_fill_first_stripe() relies on an non-empty extent root. But unfortunately scrub_find_fill_first_stripe() doesn't really expect an NULL pointer for extent root, it use extent_root to grab fs_info and triggered a NULL pointer dereference. [FIX] Add an extra check for a valid extent root at the beginning of scrub_find_fill_first_stripe(). The new error path is introduced by 42437a6386ff ("btrfs: introduce mount option rescue=ignorebadroots"), but that's pretty old, and later commit b979547513ff ("btrfs: scrub: introduce helper to find and fill sector info for a scrub_stripe") changed how we do scrub. So for kernels older than 6.6, the fix will need manual backport.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: Add check for mgmt_alloc_skb() in mgmt_device_connected() Add check for the return value of mgmt_alloc_skb() in mgmt_device_connected() to prevent null pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: idpf: fix adapter NULL pointer dereference on reboot With SRIOV enabled, idpf ends up calling into idpf_remove() twice. First via idpf_shutdown() and then again when idpf_remove() calls into sriov_disable(), because the VF devices use the idpf driver, hence the same remove routine. When that happens, it is possible for the adapter to be NULL from the first call to idpf_remove(), leading to a NULL pointer dereference. echo 1 > /sys/class/net/<netif>/device/sriov_numvfs reboot BUG: kernel NULL pointer dereference, address: 0000000000000020 ... RIP: 0010:idpf_remove+0x22/0x1f0 [idpf] ... ? idpf_remove+0x22/0x1f0 [idpf] ? idpf_remove+0x1e4/0x1f0 [idpf] pci_device_remove+0x3f/0xb0 device_release_driver_internal+0x19f/0x200 pci_stop_bus_device+0x6d/0x90 pci_stop_and_remove_bus_device+0x12/0x20 pci_iov_remove_virtfn+0xbe/0x120 sriov_disable+0x34/0xe0 idpf_sriov_configure+0x58/0x140 [idpf] idpf_remove+0x1b9/0x1f0 [idpf] idpf_shutdown+0x12/0x30 [idpf] pci_device_shutdown+0x35/0x60 device_shutdown+0x156/0x200 ... Replace the direct idpf_remove() call in idpf_shutdown() with idpf_vc_core_deinit() and idpf_deinit_dflt_mbx(), which perform the bulk of the cleanup, such as stopping the init task, freeing IRQs, destroying the vports and freeing the mailbox. This avoids the calls to sriov_disable() in addition to a small netdev cleanup, and destroying workqueues, which don't seem to be required on shutdown.

In the Linux kernel, the following vulnerability has been resolved: can: rockchip: rkcanfd_handle_rx_fifo_overflow_int(): bail out if skb cannot be allocated Fix NULL pointer check in rkcanfd_handle_rx_fifo_overflow_int() to bail out if skb cannot be allocated.

In the Linux kernel, the following vulnerability has been resolved: drm/virtio: fix NULL pointer dereference in virtio_gpu_conn_get_modes drm_cvt_mode may return NULL and we should check it. This bug is found by syzkaller: FAULT_INJECTION stacktrace: [ 168.567394] FAULT_INJECTION: forcing a failure. name failslab, interval 1, probability 0, space 0, times 1 [ 168.567403] CPU: 1 PID: 6425 Comm: syz Kdump: loaded Not tainted 4.19.90-vhulk2201.1.0.h1035.kasan.eulerosv2r10.aarch64 #1 [ 168.567406] Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015 [ 168.567408] Call trace: [ 168.567414] dump_backtrace+0x0/0x310 [ 168.567418] show_stack+0x28/0x38 [ 168.567423] dump_stack+0xec/0x15c [ 168.567427] should_fail+0x3ac/0x3d0 [ 168.567437] __should_failslab+0xb8/0x120 [ 168.567441] should_failslab+0x28/0xc0 [ 168.567445] kmem_cache_alloc_trace+0x50/0x640 [ 168.567454] drm_mode_create+0x40/0x90 [ 168.567458] drm_cvt_mode+0x48/0xc78 [ 168.567477] virtio_gpu_conn_get_modes+0xa8/0x140 [virtio_gpu] [ 168.567485] drm_helper_probe_single_connector_modes+0x3a4/0xd80 [ 168.567492] drm_mode_getconnector+0x2e0/0xa70 [ 168.567496] drm_ioctl_kernel+0x11c/0x1d8 [ 168.567514] drm_ioctl+0x558/0x6d0 [ 168.567522] do_vfs_ioctl+0x160/0xf30 [ 168.567525] ksys_ioctl+0x98/0xd8 [ 168.567530] __arm64_sys_ioctl+0x50/0xc8 [ 168.567536] el0_svc_common+0xc8/0x320 [ 168.567540] el0_svc_handler+0xf8/0x160 [ 168.567544] el0_svc+0x10/0x218 KASAN stacktrace: [ 168.567561] BUG: KASAN: null-ptr-deref in virtio_gpu_conn_get_modes+0xb4/0x140 [virtio_gpu] [ 168.567565] Read of size 4 at addr 0000000000000054 by task syz/6425 [ 168.567566] [ 168.567571] CPU: 1 PID: 6425 Comm: syz Kdump: loaded Not tainted 4.19.90-vhulk2201.1.0.h1035.kasan.eulerosv2r10.aarch64 #1 [ 168.567573] Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015 [ 168.567575] Call trace: [ 168.567578] dump_backtrace+0x0/0x310 [ 168.567582] show_stack+0x28/0x38 [ 168.567586] dump_stack+0xec/0x15c [ 168.567591] kasan_report+0x244/0x2f0 [ 168.567594] __asan_load4+0x58/0xb0 [ 168.567607] virtio_gpu_conn_get_modes+0xb4/0x140 [virtio_gpu] [ 168.567612] drm_helper_probe_single_connector_modes+0x3a4/0xd80 [ 168.567617] drm_mode_getconnector+0x2e0/0xa70 [ 168.567621] drm_ioctl_kernel+0x11c/0x1d8 [ 168.567624] drm_ioctl+0x558/0x6d0 [ 168.567628] do_vfs_ioctl+0x160/0xf30 [ 168.567632] ksys_ioctl+0x98/0xd8 [ 168.567636] __arm64_sys_ioctl+0x50/0xc8 [ 168.567641] el0_svc_common+0xc8/0x320 [ 168.567645] el0_svc_handler+0xf8/0x160 [ 168.567649] el0_svc+0x10/0x218

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7921: fix kernel panic due to null pointer dereference Address a kernel panic caused by a null pointer dereference in the `mt792x_rx_get_wcid` function. The issue arises because the `deflink` structure is not properly initialized with the `sta` context. This patch ensures that the `deflink` structure is correctly linked to the `sta` context, preventing the null pointer dereference. BUG: kernel NULL pointer dereference, address: 0000000000000400 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 0 UID: 0 PID: 470 Comm: mt76-usb-rx phy Not tainted 6.12.13-gentoo-dist #1 Hardware name: /AMD HUDSON-M1, BIOS 4.6.4 11/15/2011 RIP: 0010:mt792x_rx_get_wcid+0x48/0x140 [mt792x_lib] RSP: 0018:ffffa147c055fd98 EFLAGS: 00010202 RAX: 0000000000000000 RBX: ffff8e9ecb652000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffff8e9ecb652000 RBP: 0000000000000685 R08: ffff8e9ec6570000 R09: 0000000000000000 R10: ffff8e9ecd2ca000 R11: ffff8e9f22a217c0 R12: 0000000038010119 R13: 0000000080843801 R14: ffff8e9ec6570000 R15: ffff8e9ecb652000 FS: 0000000000000000(0000) GS:ffff8e9f22a00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000400 CR3: 000000000d2ea000 CR4: 00000000000006f0 Call Trace: <TASK> ? __die_body.cold+0x19/0x27 ? page_fault_oops+0x15a/0x2f0 ? search_module_extables+0x19/0x60 ? search_bpf_extables+0x5f/0x80 ? exc_page_fault+0x7e/0x180 ? asm_exc_page_fault+0x26/0x30 ? mt792x_rx_get_wcid+0x48/0x140 [mt792x_lib] mt7921_queue_rx_skb+0x1c6/0xaa0 [mt7921_common] mt76u_alloc_queues+0x784/0x810 [mt76_usb] ? __pfx___mt76_worker_fn+0x10/0x10 [mt76] __mt76_worker_fn+0x4f/0x80 [mt76] kthread+0xd2/0x100 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x34/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> ---[ end trace 0000000000000000 ]---

In the Linux kernel, the following vulnerability has been resolved: sctp: sysctl: plpmtud_probe_interval: avoid using current->nsproxy As mentioned in a previous commit of this series, using the 'net' structure via 'current' is not recommended for different reasons: - Inconsistency: getting info from the reader's/writer's netns vs only from the opener's netns. - current->nsproxy can be NULL in some cases, resulting in an 'Oops' (null-ptr-deref), e.g. when the current task is exiting, as spotted by syzbot [1] using acct(2). The 'net' structure can be obtained from the table->data using container_of(). Note that table->data could also be used directly, as this is the only member needed from the 'net' structure, but that would increase the size of this fix, to use '*data' everywhere 'net->sctp.probe_interval' is used.

In the Linux kernel, the following vulnerability has been resolved: iommu/vt-d: Avoid use of NULL after WARN_ON_ONCE There is a WARN_ON_ONCE to catch an unlikely situation when domain_remove_dev_pasid can't find the `pasid`. In case it nevertheless happens we must avoid using a NULL pointer.

In the Linux kernel, the following vulnerability has been resolved: powerpc/perf: Fix ref-counting on the PMU 'vpa_pmu' Commit 176cda0619b6 ("powerpc/perf: Add perf interface to expose vpa counters") introduced 'vpa_pmu' to expose Book3s-HV nested APIv2 provided L1<->L2 context switch latency counters to L1 user-space via perf-events. However the newly introduced PMU named 'vpa_pmu' doesn't assign ownership of the PMU to the module 'vpa_pmu'. Consequently the module 'vpa_pmu' can be unloaded while one of the perf-events are still active, which can lead to kernel oops and panic of the form below on a Pseries-LPAR: BUG: Kernel NULL pointer dereference on read at 0x00000058 <snip> NIP [c000000000506cb8] event_sched_out+0x40/0x258 LR [c00000000050e8a4] __perf_remove_from_context+0x7c/0x2b0 Call Trace: [c00000025fc3fc30] [c00000025f8457a8] 0xc00000025f8457a8 (unreliable) [c00000025fc3fc80] [fffffffffffffee0] 0xfffffffffffffee0 [c00000025fc3fcd0] [c000000000501e70] event_function+0xa8/0x120 <snip> Kernel panic - not syncing: Aiee, killing interrupt handler! Fix this by adding the module ownership to 'vpa_pmu' so that the module 'vpa_pmu' is ref-counted and prevented from being unloaded when perf-events are initialized.

In the Linux kernel, the following vulnerability has been resolved: usb: typec: ucsi: Fix NULL pointer access Resources should be released only after all threads that utilize them have been destroyed. This commit ensures that resources are not released prematurely by waiting for the associated workqueue to complete before deallocating them.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: NULL-check BO's backing store when determining GFX12 PTE flags PRT BOs may not have any backing store, so bo->tbo.resource will be NULL. Check for that before dereferencing. (cherry picked from commit 3e3fcd29b505cebed659311337ea03b7698767fc)

In the Linux kernel, the following vulnerability has been resolved: rds: sysctl: rds_tcp_{rcv,snd}buf: avoid using current->nsproxy As mentioned in a previous commit of this series, using the 'net' structure via 'current' is not recommended for different reasons: - Inconsistency: getting info from the reader's/writer's netns vs only from the opener's netns. - current->nsproxy can be NULL in some cases, resulting in an 'Oops' (null-ptr-deref), e.g. when the current task is exiting, as spotted by syzbot [1] using acct(2). The per-netns structure can be obtained from the table->data using container_of(), then the 'net' one can be retrieved from the listen socket (if available).

In the Linux kernel, the following vulnerability has been resolved: sctp: add mutual exclusion in proc_sctp_do_udp_port() We must serialize calls to sctp_udp_sock_stop() and sctp_udp_sock_start() or risk a crash as syzbot reported: Oops: general protection fault, probably for non-canonical address 0xdffffc000000000d: 0000 [#1] SMP KASAN PTI KASAN: null-ptr-deref in range [0x0000000000000068-0x000000000000006f] CPU: 1 UID: 0 PID: 6551 Comm: syz.1.44 Not tainted 6.14.0-syzkaller-g7f2ff7b62617 #0 PREEMPT(full) Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/12/2025 RIP: 0010:kernel_sock_shutdown+0x47/0x70 net/socket.c:3653 Call Trace: <TASK> udp_tunnel_sock_release+0x68/0x80 net/ipv4/udp_tunnel_core.c:181 sctp_udp_sock_stop+0x71/0x160 net/sctp/protocol.c:930 proc_sctp_do_udp_port+0x264/0x450 net/sctp/sysctl.c:553 proc_sys_call_handler+0x3d0/0x5b0 fs/proc/proc_sysctl.c:601 iter_file_splice_write+0x91c/0x1150 fs/splice.c:738 do_splice_from fs/splice.c:935 [inline] direct_splice_actor+0x18f/0x6c0 fs/splice.c:1158 splice_direct_to_actor+0x342/0xa30 fs/splice.c:1102 do_splice_direct_actor fs/splice.c:1201 [inline] do_splice_direct+0x174/0x240 fs/splice.c:1227 do_sendfile+0xafd/0xe50 fs/read_write.c:1368 __do_sys_sendfile64 fs/read_write.c:1429 [inline] __se_sys_sendfile64 fs/read_write.c:1415 [inline] __x64_sys_sendfile64+0x1d8/0x220 fs/read_write.c:1415 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]