In the Linux kernel, the following vulnerability has been resolved: geneve: fix header validation in geneve[6]_xmit_skb syzbot is able to trigger an uninit-value in geneve_xmit() [1] Problem : While most ip tunnel helpers (like ip_tunnel_get_dsfield()) uses skb_protocol(skb, true), pskb_inet_may_pull() is only using skb->protocol. If anything else than ETH_P_IPV6 or ETH_P_IP is found in skb->protocol, pskb_inet_may_pull() does nothing at all. If a vlan tag was provided by the caller (af_packet in the syzbot case), the network header might not point to the correct location, and skb linear part could be smaller than expected. Add skb_vlan_inet_prepare() to perform a complete mac validation. Use this in geneve for the moment, I suspect we need to adopt this more broadly. v4 - Jakub reported v3 broke l2_tos_ttl_inherit.sh selftest - Only call __vlan_get_protocol() for vlan types. v2,v3 - Addressed Sabrina comments on v1 and v2 [1] BUG: KMSAN: uninit-value in geneve_xmit_skb drivers/net/geneve.c:910 [inline] BUG: KMSAN: uninit-value in geneve_xmit+0x302d/0x5420 drivers/net/geneve.c:1030 geneve_xmit_skb drivers/net/geneve.c:910 [inline] geneve_xmit+0x302d/0x5420 drivers/net/geneve.c:1030 __netdev_start_xmit include/linux/netdevice.h:4903 [inline] netdev_start_xmit include/linux/netdevice.h:4917 [inline] xmit_one net/core/dev.c:3531 [inline] dev_hard_start_xmit+0x247/0xa20 net/core/dev.c:3547 __dev_queue_xmit+0x348d/0x52c0 net/core/dev.c:4335 dev_queue_xmit include/linux/netdevice.h:3091 [inline] packet_xmit+0x9c/0x6c0 net/packet/af_packet.c:276 packet_snd net/packet/af_packet.c:3081 [inline] packet_sendmsg+0x8bb0/0x9ef0 net/packet/af_packet.c:3113 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x30f/0x380 net/socket.c:745 __sys_sendto+0x685/0x830 net/socket.c:2191 __do_sys_sendto net/socket.c:2203 [inline] __se_sys_sendto net/socket.c:2199 [inline] __x64_sys_sendto+0x125/0x1d0 net/socket.c:2199 do_syscall_64+0xd5/0x1f0 entry_SYSCALL_64_after_hwframe+0x6d/0x75 Uninit was created at: slab_post_alloc_hook mm/slub.c:3804 [inline] slab_alloc_node mm/slub.c:3845 [inline] kmem_cache_alloc_node+0x613/0xc50 mm/slub.c:3888 kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:577 __alloc_skb+0x35b/0x7a0 net/core/skbuff.c:668 alloc_skb include/linux/skbuff.h:1318 [inline] alloc_skb_with_frags+0xc8/0xbf0 net/core/skbuff.c:6504 sock_alloc_send_pskb+0xa81/0xbf0 net/core/sock.c:2795 packet_alloc_skb net/packet/af_packet.c:2930 [inline] packet_snd net/packet/af_packet.c:3024 [inline] packet_sendmsg+0x722d/0x9ef0 net/packet/af_packet.c:3113 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x30f/0x380 net/socket.c:745 __sys_sendto+0x685/0x830 net/socket.c:2191 __do_sys_sendto net/socket.c:2203 [inline] __se_sys_sendto net/socket.c:2199 [inline] __x64_sys_sendto+0x125/0x1d0 net/socket.c:2199 do_syscall_64+0xd5/0x1f0 entry_SYSCALL_64_after_hwframe+0x6d/0x75 CPU: 0 PID: 5033 Comm: syz-executor346 Not tainted 6.9.0-rc1-syzkaller-00005-g928a87efa423 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/29/2024

In the Linux kernel, the following vulnerability has been resolved: erspan: make sure erspan_base_hdr is present in skb->head syzbot reported a problem in ip6erspan_rcv() [1] Issue is that ip6erspan_rcv() (and erspan_rcv()) no longer make sure erspan_base_hdr is present in skb linear part (skb->head) before getting @ver field from it. Add the missing pskb_may_pull() calls. v2: Reload iph pointer in erspan_rcv() after pskb_may_pull() because skb->head might have changed. [1] BUG: KMSAN: uninit-value in pskb_may_pull_reason include/linux/skbuff.h:2742 [inline] BUG: KMSAN: uninit-value in pskb_may_pull include/linux/skbuff.h:2756 [inline] BUG: KMSAN: uninit-value in ip6erspan_rcv net/ipv6/ip6_gre.c:541 [inline] BUG: KMSAN: uninit-value in gre_rcv+0x11f8/0x1930 net/ipv6/ip6_gre.c:610 pskb_may_pull_reason include/linux/skbuff.h:2742 [inline] pskb_may_pull include/linux/skbuff.h:2756 [inline] ip6erspan_rcv net/ipv6/ip6_gre.c:541 [inline] gre_rcv+0x11f8/0x1930 net/ipv6/ip6_gre.c:610 ip6_protocol_deliver_rcu+0x1d4c/0x2ca0 net/ipv6/ip6_input.c:438 ip6_input_finish net/ipv6/ip6_input.c:483 [inline] NF_HOOK include/linux/netfilter.h:314 [inline] ip6_input+0x15d/0x430 net/ipv6/ip6_input.c:492 ip6_mc_input+0xa7e/0xc80 net/ipv6/ip6_input.c:586 dst_input include/net/dst.h:460 [inline] ip6_rcv_finish+0x955/0x970 net/ipv6/ip6_input.c:79 NF_HOOK include/linux/netfilter.h:314 [inline] ipv6_rcv+0xde/0x390 net/ipv6/ip6_input.c:310 __netif_receive_skb_one_core net/core/dev.c:5538 [inline] __netif_receive_skb+0x1da/0xa00 net/core/dev.c:5652 netif_receive_skb_internal net/core/dev.c:5738 [inline] netif_receive_skb+0x58/0x660 net/core/dev.c:5798 tun_rx_batched+0x3ee/0x980 drivers/net/tun.c:1549 tun_get_user+0x5566/0x69e0 drivers/net/tun.c:2002 tun_chr_write_iter+0x3af/0x5d0 drivers/net/tun.c:2048 call_write_iter include/linux/fs.h:2108 [inline] new_sync_write fs/read_write.c:497 [inline] vfs_write+0xb63/0x1520 fs/read_write.c:590 ksys_write+0x20f/0x4c0 fs/read_write.c:643 __do_sys_write fs/read_write.c:655 [inline] __se_sys_write fs/read_write.c:652 [inline] __x64_sys_write+0x93/0xe0 fs/read_write.c:652 do_syscall_64+0xd5/0x1f0 entry_SYSCALL_64_after_hwframe+0x6d/0x75 Uninit was created at: slab_post_alloc_hook mm/slub.c:3804 [inline] slab_alloc_node mm/slub.c:3845 [inline] kmem_cache_alloc_node+0x613/0xc50 mm/slub.c:3888 kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:577 __alloc_skb+0x35b/0x7a0 net/core/skbuff.c:668 alloc_skb include/linux/skbuff.h:1318 [inline] alloc_skb_with_frags+0xc8/0xbf0 net/core/skbuff.c:6504 sock_alloc_send_pskb+0xa81/0xbf0 net/core/sock.c:2795 tun_alloc_skb drivers/net/tun.c:1525 [inline] tun_get_user+0x209a/0x69e0 drivers/net/tun.c:1846 tun_chr_write_iter+0x3af/0x5d0 drivers/net/tun.c:2048 call_write_iter include/linux/fs.h:2108 [inline] new_sync_write fs/read_write.c:497 [inline] vfs_write+0xb63/0x1520 fs/read_write.c:590 ksys_write+0x20f/0x4c0 fs/read_write.c:643 __do_sys_write fs/read_write.c:655 [inline] __se_sys_write fs/read_write.c:652 [inline] __x64_sys_write+0x93/0xe0 fs/read_write.c:652 do_syscall_64+0xd5/0x1f0 entry_SYSCALL_64_after_hwframe+0x6d/0x75 CPU: 1 PID: 5045 Comm: syz-executor114 Not tainted 6.9.0-rc1-syzkaller-00021-g962490525cff #0

In the Linux kernel, the following vulnerability has been resolved: net: hns3: fix kernel crash when devlink reload during pf initialization The devlink reload process will access the hardware resources, but the register operation is done before the hardware is initialized. So, processing the devlink reload during initialization may lead to kernel crash. This patch fixes this by taking devl_lock during initialization.

In the Linux kernel, the following vulnerability has been resolved: i40e: fix vf may be used uninitialized in this function warning To fix the regression introduced by commit 52424f974bc5, which causes servers hang in very hard to reproduce conditions with resets races. Using two sources for the information is the root cause. In this function before the fix bumping v didn't mean bumping vf pointer. But the code used this variables interchangeably, so stale vf could point to different/not intended vf. Remove redundant "v" variable and iterate via single VF pointer across whole function instead to guarantee VF pointer validity.

In the Linux kernel, the following vulnerability has been resolved: nfc: nci: Fix uninit-value in nci_dev_up and nci_ntf_packet syzbot reported the following uninit-value access issue [1][2]: nci_rx_work() parses and processes received packet. When the payload length is zero, each message type handler reads uninitialized payload and KMSAN detects this issue. The receipt of a packet with a zero-size payload is considered unexpected, and therefore, such packets should be silently discarded. This patch resolved this issue by checking payload size before calling each message type handler codes.

In the Linux kernel, the following vulnerability has been resolved: drm/sched: Check scheduler work queue before calling timeout handling During an IGT GPU reset test we see again oops despite of commit 0c8c901aaaebc9 (drm/sched: Check scheduler ready before calling timeout handling). It uses ready condition whether to call drm_sched_fault which unwind the TDR leads to GPU reset. However it looks the ready condition is overloaded with other meanings, for example, for the following stack is related GPU reset : 0 gfx_v9_0_cp_gfx_start 1 gfx_v9_0_cp_gfx_resume 2 gfx_v9_0_cp_resume 3 gfx_v9_0_hw_init 4 gfx_v9_0_resume 5 amdgpu_device_ip_resume_phase2 does the following: /* start the ring */ gfx_v9_0_cp_gfx_start(adev); ring->sched.ready = true; The same approach is for other ASICs as well : gfx_v8_0_cp_gfx_resume gfx_v10_0_kiq_resume, etc... As a result, our GPU reset test causes GPU fault which calls unconditionally gfx_v9_0_fault and then drm_sched_fault. However now it depends on whether the interrupt service routine drm_sched_fault is executed after gfx_v9_0_cp_gfx_start is completed which sets the ready field of the scheduler to true even for uninitialized schedulers and causes oops vs no fault or when ISR drm_sched_fault is completed prior gfx_v9_0_cp_gfx_start and NULL pointer dereference does not occur. Use the field timeout_wq to prevent oops for uninitialized schedulers. The field could be initialized by the work queue of resetting the domain. v1: Corrections to commit message (Luben)

In the Linux kernel, the following vulnerability has been resolved: media: cxusb: no longer judge rbuf when the write fails syzbot reported a uninit-value in cxusb_i2c_xfer. [1] Only when the write operation of usb_bulk_msg() in dvb_usb_generic_rw() succeeds and rlen is greater than 0, the read operation of usb_bulk_msg() will be executed to read rlen bytes of data from the dvb device into the rbuf. In this case, although rlen is 1, the write operation failed which resulted in the dvb read operation not being executed, and ultimately variable i was not initialized. [1] BUG: KMSAN: uninit-value in cxusb_gpio_tuner drivers/media/usb/dvb-usb/cxusb.c:124 [inline] BUG: KMSAN: uninit-value in cxusb_i2c_xfer+0x153a/0x1a60 drivers/media/usb/dvb-usb/cxusb.c:196 cxusb_gpio_tuner drivers/media/usb/dvb-usb/cxusb.c:124 [inline] cxusb_i2c_xfer+0x153a/0x1a60 drivers/media/usb/dvb-usb/cxusb.c:196 __i2c_transfer+0xe25/0x3150 drivers/i2c/i2c-core-base.c:-1 i2c_transfer+0x317/0x4a0 drivers/i2c/i2c-core-base.c:2315 i2c_transfer_buffer_flags+0x125/0x1e0 drivers/i2c/i2c-core-base.c:2343 i2c_master_send include/linux/i2c.h:109 [inline] i2cdev_write+0x210/0x280 drivers/i2c/i2c-dev.c:183 do_loop_readv_writev fs/read_write.c:848 [inline] vfs_writev+0x963/0x14e0 fs/read_write.c:1057 do_writev+0x247/0x5c0 fs/read_write.c:1101 __do_sys_writev fs/read_write.c:1169 [inline] __se_sys_writev fs/read_write.c:1166 [inline] __x64_sys_writev+0x98/0xe0 fs/read_write.c:1166 x64_sys_call+0x2229/0x3c80 arch/x86/include/generated/asm/syscalls_64.h:21 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xcd/0x1e0 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f

A NULL pointer dereference flaw was found in the Linux kernel's BPF subsystem in the way a user triggers the map_get_next_key function of the BPF bloom filter. This flaw allows a local user to crash the system. This flaw affects Linux kernel versions prior to 5.17-rc1.

In the Linux kernel, the following vulnerability has been resolved: i40e: Fix freeing of uninitialized misc IRQ vector When VSI set up failed in i40e_probe() as part of PF switch set up driver was trying to free misc IRQ vectors in i40e_clear_interrupt_scheme and produced a kernel Oops: Trying to free already-free IRQ 266 WARNING: CPU: 0 PID: 5 at kernel/irq/manage.c:1731 __free_irq+0x9a/0x300 Workqueue: events work_for_cpu_fn RIP: 0010:__free_irq+0x9a/0x300 Call Trace: ? synchronize_irq+0x3a/0xa0 free_irq+0x2e/0x60 i40e_clear_interrupt_scheme+0x53/0x190 [i40e] i40e_probe.part.108+0x134b/0x1a40 [i40e] ? kmem_cache_alloc+0x158/0x1c0 ? acpi_ut_update_ref_count.part.1+0x8e/0x345 ? acpi_ut_update_object_reference+0x15e/0x1e2 ? strstr+0x21/0x70 ? irq_get_irq_data+0xa/0x20 ? mp_check_pin_attr+0x13/0xc0 ? irq_get_irq_data+0xa/0x20 ? mp_map_pin_to_irq+0xd3/0x2f0 ? acpi_register_gsi_ioapic+0x93/0x170 ? pci_conf1_read+0xa4/0x100 ? pci_bus_read_config_word+0x49/0x70 ? do_pci_enable_device+0xcc/0x100 local_pci_probe+0x41/0x90 work_for_cpu_fn+0x16/0x20 process_one_work+0x1a7/0x360 worker_thread+0x1cf/0x390 ? create_worker+0x1a0/0x1a0 kthread+0x112/0x130 ? kthread_flush_work_fn+0x10/0x10 ret_from_fork+0x1f/0x40 The problem is that at that point misc IRQ vectors were not allocated yet and we get a call trace that driver is trying to free already free IRQ vectors. Add a check in i40e_clear_interrupt_scheme for __I40E_MISC_IRQ_REQUESTED PF state before calling i40e_free_misc_vector. This state is set only if misc IRQ vectors were properly initialized.

In the Linux kernel, the following vulnerability has been resolved: vdpa_sim: avoid putting an uninitialized iova_domain The system will crash if we put an uninitialized iova_domain, this could happen when an error occurs before initializing the iova_domain in vdpasim_create(). BUG: kernel NULL pointer dereference, address: 0000000000000000 ... RIP: 0010:__cpuhp_state_remove_instance+0x96/0x1c0 ... Call Trace: <TASK> put_iova_domain+0x29/0x220 vdpasim_free+0xd1/0x120 [vdpa_sim] vdpa_release_dev+0x21/0x40 [vdpa] device_release+0x33/0x90 kobject_release+0x63/0x160 vdpasim_create+0x127/0x2a0 [vdpa_sim] vdpasim_net_dev_add+0x7d/0xfe [vdpa_sim_net] vdpa_nl_cmd_dev_add_set_doit+0xe1/0x1a0 [vdpa] genl_family_rcv_msg_doit+0x112/0x140 genl_rcv_msg+0xdf/0x1d0 ... So we must make sure the iova_domain is already initialized before put it. In addition, we may get the following warning in this case: WARNING: ... drivers/iommu/iova.c:344 iova_cache_put+0x58/0x70 So we must make sure the iova_cache_put() is invoked only if the iova_cache_get() is already invoked. Let's fix it together.

In the Linux kernel, the following vulnerability has been resolved: rseq: Fix using an uninitialized stack variable in rseq_exit_user_update() There is an bug in which an uninitialized stack variable is used in rseq_exit_user_update() as reported by syzbot: BUG: KMSAN: kernel-infoleak in rseq_set_ids_get_csaddr include/linux/rseq_entry.h:502 [inline] The local variable: struct rseq_ids ids = { .cpu_id = task_cpu(t), .mm_cid = task_mm_cid(t), .node_id = cpu_to_node(ids.cpu_id), }; According to the C standard, the evaluation order of expressions in an initializer list is indeterminately sequenced. The compiler (Clang, in this KMSAN build) evaluates `cpu_to_node(ids.cpu_id)` *before* `ids.cpu_id` is initialized with `task_cpu(t)`. This is fixed by moving the assignment of ids.node_id outside the structure initialization.

In the Linux kernel, the following vulnerability has been resolved: fuse: fix uninit-value in fuse_dentry_revalidate() fuse_dentry_revalidate() may be called with a dentry that didn't had ->d_time initialised. The issue was found with KMSAN, where lookup_open() calls __d_alloc(), followed by d_revalidate(), as shown below: ===================================================== BUG: KMSAN: uninit-value in fuse_dentry_revalidate+0x150/0x13d0 fs/fuse/dir.c:394 fuse_dentry_revalidate+0x150/0x13d0 fs/fuse/dir.c:394 d_revalidate fs/namei.c:1030 [inline] lookup_open fs/namei.c:4405 [inline] open_last_lookups fs/namei.c:4583 [inline] path_openat+0x1614/0x64c0 fs/namei.c:4827 do_file_open+0x2aa/0x680 fs/namei.c:4859 [...] Uninit was created at: slab_post_alloc_hook mm/slub.c:4466 [inline] slab_alloc_node mm/slub.c:4788 [inline] kmem_cache_alloc_lru_noprof+0x382/0x1280 mm/slub.c:4807 __d_alloc+0x55/0xa00 fs/dcache.c:1740 d_alloc_parallel+0x99/0x2740 fs/dcache.c:2604 lookup_open fs/namei.c:4398 [inline] open_last_lookups fs/namei.c:4583 [inline] path_openat+0x135f/0x64c0 fs/namei.c:4827 do_file_open+0x2aa/0x680 fs/namei.c:4859 [...] =====================================================

In the Linux kernel, the following vulnerability has been resolved: net: hamradio: 6pack: fix uninit-value in sixpack_receive_buf sixpack_receive_buf() does not properly skip bytes with TTY error flags. The while loop iterates through the flags buffer but never advances the data pointer (cp), and passes the original count (including error bytes) to sixpack_decode(). This causes sixpack_decode() to process bytes that should have been skipped due to TTY errors. The TTY layer does not guarantee that cp[i] holds a meaningful value when fp[i] is set, so passing those positions to sixpack_decode() results in KMSAN reporting an uninit-value read. Fix this by processing bytes one at a time, advancing cp on each iteration, and only passing valid (non-error) bytes to sixpack_decode(). This matches the pattern used by slip_receive_buf() and mkiss_receive_buf() for the same purpose.

In the Linux kernel, the following vulnerability has been resolved: drm/xe/display: fix oops in suspend/shutdown without display The xe driver keeps track of whether to probe display, and whether display hardware is there, using xe->info.probe_display. It gets set to false if there's no display after intel_display_device_probe(). However, the display may also be disabled via fuses, detected at a later time in intel_display_device_info_runtime_init(). In this case, the xe driver does for_each_intel_crtc() on uninitialized mode config in xe_display_flush_cleanup_work(), leading to a NULL pointer dereference, and generally calls display code with display info cleared. Check for intel_display_device_present() after intel_display_device_info_runtime_init(), and reset xe->info.probe_display as necessary. Also do unset_display_features() for completeness, although display runtime init has already done that. This will need to be unified across all cases later. Move intel_display_device_info_runtime_init() call slightly earlier, similar to i915, to avoid a bunch of unnecessary setup for no display cases. Note #1: The xe driver has no business doing low level display plumbing like for_each_intel_crtc() to begin with. It all needs to happen in display code. Note #2: The actual bug is present already in commit 44e694958b95 ("drm/xe/display: Implement display support"), but the oops was likely introduced later at commit ddf6492e0e50 ("drm/xe/display: Make display suspend/resume work on discrete"). (cherry picked from commit 7c3eb9f47533220888a67266448185fd0775d4da)

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: prevent uninitialized lcn caused by zero len syzbot reported a uninit-value in ntfs_iomap_begin [1]. Since runs was not touched yet, run_lookup_entry() immediately fails and returns false, which makes the value of "*len" 0. Simultaneously, the new value and err value are also 0, causing the logic in attr_data_get_block_locked() to jump directly to ok, ultimately resulting in *lcn being triggered before it is set [1]. In ntfs_iomap_begin(), the check for a 0 value in clen is moved forward to before updating lcn to avoid this [1]. [1] BUG: KMSAN: uninit-value in ntfs_iomap_begin+0x8c0/0x1460 fs/ntfs3/inode.c:825 ntfs_iomap_begin+0x8c0/0x1460 fs/ntfs3/inode.c:825 iomap_iter+0x9b7/0x1540 fs/iomap/iter.c:110 Local variable lcn created at: ntfs_iomap_begin+0x15d/0x1460 fs/ntfs3/inode.c:786

In the Linux kernel, the following vulnerability has been resolved: netfilter: nft_exthdr: fix register tracking for F_PRESENT flag nft_exthdr_init() passes user-controlled priv->len to nft_parse_register_store(), which marks that many bytes in the register bitmap as initialized. However, when NFT_EXTHDR_F_PRESENT is set, the eval paths write only 1 byte (nft_reg_store8) or 4 bytes (*dest = 0 on TCP/DCCP error path). When len > 4, registers beyond the first are never written, retaining uninitialized stack data from nft_regs. Bail out if userspace requests too much data when F_PRESENT is set.

In the Linux kernel, the following vulnerability has been resolved: clocksource/drivers/timer-sp804: Fix an Oops when read_current_timer is called on ARM32 platforms where the SP804 is not registered as the sched_clock. On SP804, the delay timer shares the same clkevt instance with sched_clock. On some platforms, when sp804_clocksource_and_sched_clock_init is called with use_sched_clock not set to 1, sched_clkevt is not properly initialized. However, sp804_register_delay_timer is invoked unconditionally, and read_current_timer() subsequently calls sp804_read on an uninitialized sched_clkevt, leading to a kernel Oops when accessing sched_clkevt->value. Declare a dedicated clkevt instance exclusively for delay timer, instead of sharing the same clkevt with sched_clock. This ensures that read_current_timer continues to work correctly regardless of whether SP804 is selected as the sched_clock.

In the Linux kernel, the following vulnerability has been resolved: crypto: qat - ADF_STATUS_PF_RUNNING should be set after adf_dev_init ADF_STATUS_PF_RUNNING is (only) used and checked by adf_vf2pf_shutdown() before calling adf_iov_putmsg()->mutex_lock(vf2pf_lock), however the vf2pf_lock is initialized in adf_dev_init(), which can fail and when it fail, the vf2pf_lock is either not initialized or destroyed, a subsequent use of vf2pf_lock will cause issue. To fix this issue, only set this flag if adf_dev_init() returns 0. [ 7.178404] BUG: KASAN: user-memory-access in __mutex_lock.isra.0+0x1ac/0x7c0 [ 7.180345] Call Trace: [ 7.182576] mutex_lock+0xc9/0xd0 [ 7.183257] adf_iov_putmsg+0x118/0x1a0 [intel_qat] [ 7.183541] adf_vf2pf_shutdown+0x4d/0x7b [intel_qat] [ 7.183834] adf_dev_shutdown+0x172/0x2b0 [intel_qat] [ 7.184127] adf_probe+0x5e9/0x600 [qat_dh895xccvf]

In the Linux kernel, the following vulnerability has been resolved: usb: usblp: fix uninitialized heap leak via LPGETSTATUS ioctl Just like in a previous problem in this driver, usblp_ctrl_msg() will collapse the usb_control_msg() return value to 0/-errno, discarding the actual number of bytes transferred. Ideally that short command should be detected and error out, but many printers are known to send "incorrect" responses back so we can't just do that. statusbuf is kmalloc(8) at probe time and never filled before the first LPGETSTATUS ioctl. usblp_read_status() requests 1 byte. If a malicious printer responds with zero bytes, *statusbuf is one byte of stale kmalloc heap, sign-extended into the local int status, which the LPGETSTATUS path then copy_to_user()s directly to the ioctl caller. Fix this all by just zapping out the memory buffer when allocated at probe time. If a later call does a short read, the data will be identical to what the device sent it the last time, so there is no "leak" of information happening.

In the Linux kernel, the following vulnerability has been resolved: hfsplus: fix uninit-value by validating catalog record size Syzbot reported a KMSAN uninit-value issue in hfsplus_strcasecmp(). The root cause is that hfs_brec_read() doesn't validate that the on-disk record size matches the expected size for the record type being read. When mounting a corrupted filesystem, hfs_brec_read() may read less data than expected. For example, when reading a catalog thread record, the debug output showed: HFSPLUS_BREC_READ: rec_len=520, fd->entrylength=26 HFSPLUS_BREC_READ: WARNING - entrylength (26) < rec_len (520) - PARTIAL READ! hfs_brec_read() only validates that entrylength is not greater than the buffer size, but doesn't check if it's less than expected. It successfully reads 26 bytes into a 520-byte structure and returns success, leaving 494 bytes uninitialized. This uninitialized data in tmp.thread.nodeName then gets copied by hfsplus_cat_build_key_uni() and used by hfsplus_strcasecmp(), triggering the KMSAN warning when the uninitialized bytes are used as array indices in case_fold(). Fix by introducing hfsplus_brec_read_cat() wrapper that: 1. Calls hfs_brec_read() to read the data 2. Validates the record size based on the type field: - Fixed size for folder and file records - Variable size for thread records (depends on string length) 3. Returns -EIO if size doesn't match expected For thread records, check against HFSPLUS_MIN_THREAD_SZ before reading nodeName.length to avoid reading uninitialized data at call sites that don't zero-initialize the entry structure. Also initialize the tmp variable in hfsplus_find_cat() as defensive programming to ensure no uninitialized data even if validation is bypassed.

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix bpf_xdp_store_bytes proto for read-only arg While making some maps in Cilium read-only from the BPF side, we noticed that the bpf_xdp_store_bytes proto is incorrect. In particular, the verifier was throwing the following error: ; ret = ctx_store_bytes(ctx, l3_off + offsetof(struct iphdr, saddr), &nat->address, 4, 0); 635: (79) r1 = *(u64 *)(r10 -144) ; R1=ctx() R10=fp0 fp-144=ctx() 636: (b4) w2 = 26 ; R2=26 637: (b4) w4 = 4 ; R4=4 638: (b4) w5 = 0 ; R5=0 639: (85) call bpf_xdp_store_bytes#190 write into map forbidden, value_size=6 off=0 size=4 nat comes from a BPF_F_RDONLY_PROG map, so R3 is a PTR_TO_MAP_VALUE. The verifier checks the helper's memory access to R3 in check_mem_size_reg, as it reaches ARG_CONST_SIZE argument. The third argument has expected type ARG_PTR_TO_UNINIT_MEM, which includes the MEM_WRITE flag. The verifier thus checks for a BPF_WRITE access on R3. Given R3 points to a read-only map, the check fails. Conversely, ARG_PTR_TO_UNINIT_MEM can also lead to the helper reading from uninitialized memory. This patch simply fixes the expected argument type to match that of bpf_skb_store_bytes.

In the Linux kernel, the following vulnerability has been resolved: net: rtnetlink: zero ifla_vf_broadcast to avoid stack infoleak in rtnl_fill_vfinfo rtnl_fill_vfinfo() declares struct ifla_vf_broadcast on the stack without initialisation: struct ifla_vf_broadcast vf_broadcast; The struct contains a single fixed 32-byte field: /* include/uapi/linux/if_link.h */ struct ifla_vf_broadcast { __u8 broadcast[32]; }; The function then copies dev->broadcast into it using dev->addr_len as the length: memcpy(vf_broadcast.broadcast, dev->broadcast, dev->addr_len); On Ethernet devices (the overwhelming majority of SR-IOV NICs) dev->addr_len is 6, so only the first 6 bytes of broadcast[] are written. The remaining 26 bytes retain whatever was previously on the kernel stack. The full struct is then handed to userspace via: nla_put(skb, IFLA_VF_BROADCAST, sizeof(vf_broadcast), &vf_broadcast) leaking up to 26 bytes of uninitialised kernel stack per VF per RTM_GETLINK request, repeatable. The other vf_* structs in the same function are explicitly zeroed for exactly this reason - see the memset() calls for ivi, vf_vlan_info, node_guid and port_guid a few lines above. vf_broadcast was simply missed when it was added. Reachability: any unprivileged local process can open AF_NETLINK / NETLINK_ROUTE without capabilities and send RTM_GETLINK with an IFLA_EXT_MASK attribute carrying RTEXT_FILTER_VF. The kernel walks each VF and emits IFLA_VF_BROADCAST, leaking 26 bytes of stack per VF per request. Stack residue at this call site can include return addresses and transient sensitive data; KASAN with stack instrumentation, or KMSAN, will flag the nla_put() when reproduced. Zero the on-stack struct before the partial memcpy, matching the existing pattern used for the other vf_* structs in the same function.

In the Linux kernel, the following vulnerability has been resolved: mm/mempolicy: do not allow illegal MPOL_F_NUMA_BALANCING | MPOL_LOCAL in mbind() syzbot reported access to unitialized memory in mbind() [1] Issue came with commit bda420b98505 ("numa balancing: migrate on fault among multiple bound nodes") This commit added a new bit in MPOL_MODE_FLAGS, but only checked valid combination (MPOL_F_NUMA_BALANCING can only be used with MPOL_BIND) in do_set_mempolicy() This patch moves the check in sanitize_mpol_flags() so that it is also used by mbind() [1] BUG: KMSAN: uninit-value in __mpol_equal+0x567/0x590 mm/mempolicy.c:2260 __mpol_equal+0x567/0x590 mm/mempolicy.c:2260 mpol_equal include/linux/mempolicy.h:105 [inline] vma_merge+0x4a1/0x1e60 mm/mmap.c:1190 mbind_range+0xcc8/0x1e80 mm/mempolicy.c:811 do_mbind+0xf42/0x15f0 mm/mempolicy.c:1333 kernel_mbind mm/mempolicy.c:1483 [inline] __do_sys_mbind mm/mempolicy.c:1490 [inline] __se_sys_mbind+0x437/0xb80 mm/mempolicy.c:1486 __x64_sys_mbind+0x19d/0x200 mm/mempolicy.c:1486 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x54/0xd0 arch/x86/entry/common.c:82 entry_SYSCALL_64_after_hwframe+0x44/0xae Uninit was created at: slab_alloc_node mm/slub.c:3221 [inline] slab_alloc mm/slub.c:3230 [inline] kmem_cache_alloc+0x751/0xff0 mm/slub.c:3235 mpol_new mm/mempolicy.c:293 [inline] do_mbind+0x912/0x15f0 mm/mempolicy.c:1289 kernel_mbind mm/mempolicy.c:1483 [inline] __do_sys_mbind mm/mempolicy.c:1490 [inline] __se_sys_mbind+0x437/0xb80 mm/mempolicy.c:1486 __x64_sys_mbind+0x19d/0x200 mm/mempolicy.c:1486 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x54/0xd0 arch/x86/entry/common.c:82 entry_SYSCALL_64_after_hwframe+0x44/0xae ===================================================== Kernel panic - not syncing: panic_on_kmsan set ... CPU: 0 PID: 15049 Comm: syz-executor.0 Tainted: G B 5.15.0-rc2-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x1ff/0x28e lib/dump_stack.c:106 dump_stack+0x25/0x28 lib/dump_stack.c:113 panic+0x44f/0xdeb kernel/panic.c:232 kmsan_report+0x2ee/0x300 mm/kmsan/report.c:186 __msan_warning+0xd7/0x150 mm/kmsan/instrumentation.c:208 __mpol_equal+0x567/0x590 mm/mempolicy.c:2260 mpol_equal include/linux/mempolicy.h:105 [inline] vma_merge+0x4a1/0x1e60 mm/mmap.c:1190 mbind_range+0xcc8/0x1e80 mm/mempolicy.c:811 do_mbind+0xf42/0x15f0 mm/mempolicy.c:1333 kernel_mbind mm/mempolicy.c:1483 [inline] __do_sys_mbind mm/mempolicy.c:1490 [inline] __se_sys_mbind+0x437/0xb80 mm/mempolicy.c:1486 __x64_sys_mbind+0x19d/0x200 mm/mempolicy.c:1486 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x54/0xd0 arch/x86/entry/common.c:82 entry_SYSCALL_64_after_hwframe+0x44/0xae

In the Linux kernel, the following vulnerability has been resolved: smb: client: use kzalloc to zero-initialize security descriptor buffer Commit 62e7dd0a39c2d ("smb: common: change the data type of num_aces to le16") split struct smb_acl's __le32 num_aces field into __le16 num_aces and __le16 reserved. The reserved field corresponds to Sbz2 in the MS-DTYP ACL wire format, which must be zero [1]. When building an ACL descriptor in build_sec_desc(), we are using a kmalloc()'ed descriptor buffer and writing the fields explicitly using le16() writes now. This never writes to the 2 byte reserved field, leaving it as uninitialized heap data. When the reserved field happens to contain non-zero slab garbage, Samba rejects the security descriptor with "ndr_pull_security_descriptor failed: Range Error", causing chmod to fail with EINVAL. Change kmalloc() to kzalloc() to ensure the entire buffer is zero-initialized. [1] https://learn.microsoft.com/en-us/openspecs/windows_protocols/ms-dtyp/20233ed8-a6c6-4097-aafa-dd545ed24428

In the Linux kernel, the following vulnerability has been resolved: Input: iforce - invert valid length check when fetching device IDs syzbot is reporting uninitialized value at iforce_init_device() [1], for commit 6ac0aec6b0a6 ("Input: iforce - allow callers supply data buffer when fetching device IDs") is checking that valid length is shorter than bytes to read. Since iforce_get_id_packet() stores valid length when returning 0, the caller needs to check that valid length is longer than or equals to bytes to read.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to avoid uninit-value access in f2fs_sanity_check_node_footer syzbot reported a f2fs bug as below: BUG: KMSAN: uninit-value in f2fs_sanity_check_node_footer+0x374/0xa20 fs/f2fs/node.c:1520 f2fs_sanity_check_node_footer+0x374/0xa20 fs/f2fs/node.c:1520 f2fs_finish_read_bio+0xe1e/0x1d60 fs/f2fs/data.c:177 f2fs_read_end_io+0x6ab/0x2220 fs/f2fs/data.c:-1 bio_endio+0x1006/0x1160 block/bio.c:1792 submit_bio_noacct+0x533/0x2960 block/blk-core.c:891 submit_bio+0x57a/0x620 block/blk-core.c:926 blk_crypto_submit_bio include/linux/blk-crypto.h:203 [inline] f2fs_submit_read_bio+0x12c/0x360 fs/f2fs/data.c:557 f2fs_submit_page_bio+0xee2/0x1450 fs/f2fs/data.c:775 read_node_folio+0x384/0x4b0 fs/f2fs/node.c:1481 __get_node_folio+0x5db/0x15d0 fs/f2fs/node.c:1576 f2fs_get_inode_folio+0x40/0x50 fs/f2fs/node.c:1623 do_read_inode fs/f2fs/inode.c:425 [inline] f2fs_iget+0x1209/0x9380 fs/f2fs/inode.c:596 f2fs_fill_super+0x8f5a/0xb2e0 fs/f2fs/super.c:5184 get_tree_bdev_flags+0x6e6/0x920 fs/super.c:1694 get_tree_bdev+0x38/0x50 fs/super.c:1717 f2fs_get_tree+0x35/0x40 fs/f2fs/super.c:5436 vfs_get_tree+0xb3/0x5d0 fs/super.c:1754 fc_mount fs/namespace.c:1193 [inline] do_new_mount_fc fs/namespace.c:3763 [inline] do_new_mount+0x885/0x1dd0 fs/namespace.c:3839 path_mount+0x7a2/0x20b0 fs/namespace.c:4159 do_mount fs/namespace.c:4172 [inline] __do_sys_mount fs/namespace.c:4361 [inline] __se_sys_mount+0x704/0x7f0 fs/namespace.c:4338 __x64_sys_mount+0xe4/0x150 fs/namespace.c:4338 x64_sys_call+0x39f0/0x3ea0 arch/x86/include/generated/asm/syscalls_64.h:166 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0x134/0xf80 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f The root cause is: in f2fs_finish_read_bio(), we may access uninit data in folio if we failed to read the data from device into folio, let's add a check condition to avoid such issue.

In the Linux kernel, the following vulnerability has been resolved: kcm: fix strp_init() order and cleanup strp_init() is called just a few lines above this csk->sk_user_data check, it also initializes strp->work etc., therefore, it is unnecessary to call strp_done() to cancel the freshly initialized work. And if sk_user_data is already used by KCM, psock->strp should not be touched, particularly strp->work state, so we need to move strp_init() after the csk->sk_user_data check. This also makes a lockdep warning reported by syzbot go away.

In the Linux kernel, the following vulnerability has been resolved: mm/mempolicy: fix uninit-value in mpol_rebind_policy() mpol_set_nodemask()(mm/mempolicy.c) does not set up nodemask when pol->mode is MPOL_LOCAL. Check pol->mode before access pol->w.cpuset_mems_allowed in mpol_rebind_policy()(mm/mempolicy.c). BUG: KMSAN: uninit-value in mpol_rebind_policy mm/mempolicy.c:352 [inline] BUG: KMSAN: uninit-value in mpol_rebind_task+0x2ac/0x2c0 mm/mempolicy.c:368 mpol_rebind_policy mm/mempolicy.c:352 [inline] mpol_rebind_task+0x2ac/0x2c0 mm/mempolicy.c:368 cpuset_change_task_nodemask kernel/cgroup/cpuset.c:1711 [inline] cpuset_attach+0x787/0x15e0 kernel/cgroup/cpuset.c:2278 cgroup_migrate_execute+0x1023/0x1d20 kernel/cgroup/cgroup.c:2515 cgroup_migrate kernel/cgroup/cgroup.c:2771 [inline] cgroup_attach_task+0x540/0x8b0 kernel/cgroup/cgroup.c:2804 __cgroup1_procs_write+0x5cc/0x7a0 kernel/cgroup/cgroup-v1.c:520 cgroup1_tasks_write+0x94/0xb0 kernel/cgroup/cgroup-v1.c:539 cgroup_file_write+0x4c2/0x9e0 kernel/cgroup/cgroup.c:3852 kernfs_fop_write_iter+0x66a/0x9f0 fs/kernfs/file.c:296 call_write_iter include/linux/fs.h:2162 [inline] new_sync_write fs/read_write.c:503 [inline] vfs_write+0x1318/0x2030 fs/read_write.c:590 ksys_write+0x28b/0x510 fs/read_write.c:643 __do_sys_write fs/read_write.c:655 [inline] __se_sys_write fs/read_write.c:652 [inline] __x64_sys_write+0xdb/0x120 fs/read_write.c:652 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x54/0xd0 arch/x86/entry/common.c:82 entry_SYSCALL_64_after_hwframe+0x44/0xae Uninit was created at: slab_post_alloc_hook mm/slab.h:524 [inline] slab_alloc_node mm/slub.c:3251 [inline] slab_alloc mm/slub.c:3259 [inline] kmem_cache_alloc+0x902/0x11c0 mm/slub.c:3264 mpol_new mm/mempolicy.c:293 [inline] do_set_mempolicy+0x421/0xb70 mm/mempolicy.c:853 kernel_set_mempolicy mm/mempolicy.c:1504 [inline] __do_sys_set_mempolicy mm/mempolicy.c:1510 [inline] __se_sys_set_mempolicy+0x44c/0xb60 mm/mempolicy.c:1507 __x64_sys_set_mempolicy+0xd8/0x110 mm/mempolicy.c:1507 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x54/0xd0 arch/x86/entry/common.c:82 entry_SYSCALL_64_after_hwframe+0x44/0xae KMSAN: uninit-value in mpol_rebind_task (2) https://syzkaller.appspot.com/bug?id=d6eb90f952c2a5de9ea718a1b873c55cb13b59dc This patch seems to fix below bug too. KMSAN: uninit-value in mpol_rebind_mm (2) https://syzkaller.appspot.com/bug?id=f2fecd0d7013f54ec4162f60743a2b28df40926b The uninit-value is pol->w.cpuset_mems_allowed in mpol_rebind_policy(). When syzkaller reproducer runs to the beginning of mpol_new(), mpol_new() mm/mempolicy.c do_mbind() mm/mempolicy.c kernel_mbind() mm/mempolicy.c `mode` is 1(MPOL_PREFERRED), nodes_empty(*nodes) is `true` and `flags` is 0. Then mode = MPOL_LOCAL; ... policy->mode = mode; policy->flags = flags; will be executed. So in mpol_set_nodemask(), mpol_set_nodemask() mm/mempolicy.c do_mbind() kernel_mbind() pol->mode is 4 (MPOL_LOCAL), that `nodemask` in `pol` is not initialized, which will be accessed in mpol_rebind_policy().

In the Linux kernel, the following vulnerability has been resolved: net: sched: cls_api: fix tc_chain_fill_node to initialize tcm_info to zero to prevent an info-leak When building netlink messages, tc_chain_fill_node() never initializes the tcm_info field of struct tcmsg. Since the allocation is not zeroed, kernel heap memory is leaked to userspace through this 4-byte field. The fix simply zeroes tcm_info alongside the other fields that are already initialized.

In the Linux kernel, the following vulnerability has been resolved: ipmi: ipmb: initialise event handler read bytes IPMB doesn't use i2c reads, but the handler needs to set a value. Otherwise an i2c read will return an uninitialised value from the bus driver.

In the Linux kernel, the following vulnerability has been resolved: cxl/region: Do not try to cleanup after cxl_region_setup_targets() fails Commit 5e42bcbc3fef ("cxl/region: decrement ->nr_targets on error in cxl_region_attach()") tried to avoid 'eiw' initialization errors when ->nr_targets exceeded 16, by just decrementing ->nr_targets when cxl_region_setup_targets() failed. Commit 86987c766276 ("cxl/region: Cleanup target list on attach error") extended that cleanup to also clear cxled->pos and p->targets[pos]. The initialization error was incidentally fixed separately by: Commit 8d4285425714 ("cxl/region: Fix port setup uninitialized variable warnings") which was merged a few days after 5e42bcbc3fef. But now the original cleanup when cxl_region_setup_targets() fails prevents endpoint and switch decoder resources from being reused: 1) the cleanup does not set the decoder's region to NULL, which results in future dpa_size_store() calls returning -EBUSY 2) the decoder is not properly freed, which results in future commit errors associated with the upstream switch Now that the initialization errors were fixed separately, the proper cleanup for this case is to just return immediately. Then the resources associated with this target get cleanup up as normal when the failed region is deleted. The ->nr_targets decrement in the error case also helped prevent a p->targets[] array overflow, so add a new check to prevent against that overflow. Tested by trying to create an invalid region for a 2 switch * 2 endpoint topology, and then following up with creating a valid region.

In the Linux kernel, the following vulnerability has been resolved: fs: init flags_valid before calling vfs_fileattr_get syzbot reported a uninit-value bug in [1]. Similar to the "*get" context where the kernel's internal file_kattr structure is initialized before calling vfs_fileattr_get(), we should use the same mechanism when using fa. [1] BUG: KMSAN: uninit-value in fuse_fileattr_get+0xeb4/0x1450 fs/fuse/ioctl.c:517 fuse_fileattr_get+0xeb4/0x1450 fs/fuse/ioctl.c:517 vfs_fileattr_get fs/file_attr.c:94 [inline] __do_sys_file_getattr fs/file_attr.c:416 [inline] Local variable fa.i created at: __do_sys_file_getattr fs/file_attr.c:380 [inline] __se_sys_file_getattr+0x8c/0xbd0 fs/file_attr.c:372

In the Linux kernel, the following vulnerability has been resolved: btrfs: don't abort filesystem when attempting to snapshot deleted subvolume If the source file descriptor to the snapshot ioctl refers to a deleted subvolume, we get the following abort: BTRFS: Transaction aborted (error -2) WARNING: CPU: 0 PID: 833 at fs/btrfs/transaction.c:1875 create_pending_snapshot+0x1040/0x1190 [btrfs] Modules linked in: pata_acpi btrfs ata_piix libata scsi_mod virtio_net blake2b_generic xor net_failover virtio_rng failover scsi_common rng_core raid6_pq libcrc32c CPU: 0 PID: 833 Comm: t_snapshot_dele Not tainted 6.7.0-rc6 #2 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-1.fc39 04/01/2014 RIP: 0010:create_pending_snapshot+0x1040/0x1190 [btrfs] RSP: 0018:ffffa09c01337af8 EFLAGS: 00010282 RAX: 0000000000000000 RBX: ffff9982053e7c78 RCX: 0000000000000027 RDX: ffff99827dc20848 RSI: 0000000000000001 RDI: ffff99827dc20840 RBP: ffffa09c01337c00 R08: 0000000000000000 R09: ffffa09c01337998 R10: 0000000000000003 R11: ffffffffb96da248 R12: fffffffffffffffe R13: ffff99820535bb28 R14: ffff99820b7bd000 R15: ffff99820381ea80 FS: 00007fe20aadabc0(0000) GS:ffff99827dc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000559a120b502f CR3: 00000000055b6000 CR4: 00000000000006f0 Call Trace: <TASK> ? create_pending_snapshot+0x1040/0x1190 [btrfs] ? __warn+0x81/0x130 ? create_pending_snapshot+0x1040/0x1190 [btrfs] ? report_bug+0x171/0x1a0 ? handle_bug+0x3a/0x70 ? exc_invalid_op+0x17/0x70 ? asm_exc_invalid_op+0x1a/0x20 ? create_pending_snapshot+0x1040/0x1190 [btrfs] ? create_pending_snapshot+0x1040/0x1190 [btrfs] create_pending_snapshots+0x92/0xc0 [btrfs] btrfs_commit_transaction+0x66b/0xf40 [btrfs] btrfs_mksubvol+0x301/0x4d0 [btrfs] btrfs_mksnapshot+0x80/0xb0 [btrfs] __btrfs_ioctl_snap_create+0x1c2/0x1d0 [btrfs] btrfs_ioctl_snap_create_v2+0xc4/0x150 [btrfs] btrfs_ioctl+0x8a6/0x2650 [btrfs] ? kmem_cache_free+0x22/0x340 ? do_sys_openat2+0x97/0xe0 __x64_sys_ioctl+0x97/0xd0 do_syscall_64+0x46/0xf0 entry_SYSCALL_64_after_hwframe+0x6e/0x76 RIP: 0033:0x7fe20abe83af RSP: 002b:00007ffe6eff1360 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 0000000000000004 RCX: 00007fe20abe83af RDX: 00007ffe6eff23c0 RSI: 0000000050009417 RDI: 0000000000000003 RBP: 0000000000000003 R08: 0000000000000000 R09: 00007fe20ad16cd0 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 00007ffe6eff13c0 R14: 00007fe20ad45000 R15: 0000559a120b6d58 </TASK> ---[ end trace 0000000000000000 ]--- BTRFS: error (device vdc: state A) in create_pending_snapshot:1875: errno=-2 No such entry BTRFS info (device vdc: state EA): forced readonly BTRFS warning (device vdc: state EA): Skipping commit of aborted transaction. BTRFS: error (device vdc: state EA) in cleanup_transaction:2055: errno=-2 No such entry This happens because create_pending_snapshot() initializes the new root item as a copy of the source root item. This includes the refs field, which is 0 for a deleted subvolume. The call to btrfs_insert_root() therefore inserts a root with refs == 0. btrfs_get_new_fs_root() then finds the root and returns -ENOENT if refs == 0, which causes create_pending_snapshot() to abort. Fix it by checking the source root's refs before attempting the snapshot, but after locking subvol_sem to avoid racing with deletion.

In the Linux kernel, the following vulnerability has been resolved: drm/msm/a4xx: fix error handling in a4xx_gpu_init() This code returns 1 on error instead of a negative error. It leads to an Oops in the caller. A second problem is that the check for "if (ret != -ENODATA)" cannot be true because "ret" is set to 1.

In the Linux kernel, the following vulnerability has been resolved: ip6_tunnel: make sure to pull inner header in __ip6_tnl_rcv() syzbot found __ip6_tnl_rcv() could access unitiliazed data [1]. Call pskb_inet_may_pull() to fix this, and initialize ipv6h variable after this call as it can change skb->head. [1] BUG: KMSAN: uninit-value in __INET_ECN_decapsulate include/net/inet_ecn.h:253 [inline] BUG: KMSAN: uninit-value in INET_ECN_decapsulate include/net/inet_ecn.h:275 [inline] BUG: KMSAN: uninit-value in IP6_ECN_decapsulate+0x7df/0x1e50 include/net/inet_ecn.h:321 __INET_ECN_decapsulate include/net/inet_ecn.h:253 [inline] INET_ECN_decapsulate include/net/inet_ecn.h:275 [inline] IP6_ECN_decapsulate+0x7df/0x1e50 include/net/inet_ecn.h:321 ip6ip6_dscp_ecn_decapsulate+0x178/0x1b0 net/ipv6/ip6_tunnel.c:727 __ip6_tnl_rcv+0xd4e/0x1590 net/ipv6/ip6_tunnel.c:845 ip6_tnl_rcv+0xce/0x100 net/ipv6/ip6_tunnel.c:888 gre_rcv+0x143f/0x1870 ip6_protocol_deliver_rcu+0xda6/0x2a60 net/ipv6/ip6_input.c:438 ip6_input_finish net/ipv6/ip6_input.c:483 [inline] NF_HOOK include/linux/netfilter.h:314 [inline] ip6_input+0x15d/0x430 net/ipv6/ip6_input.c:492 ip6_mc_input+0xa7e/0xc80 net/ipv6/ip6_input.c:586 dst_input include/net/dst.h:461 [inline] ip6_rcv_finish+0x5db/0x870 net/ipv6/ip6_input.c:79 NF_HOOK include/linux/netfilter.h:314 [inline] ipv6_rcv+0xda/0x390 net/ipv6/ip6_input.c:310 __netif_receive_skb_one_core net/core/dev.c:5532 [inline] __netif_receive_skb+0x1a6/0x5a0 net/core/dev.c:5646 netif_receive_skb_internal net/core/dev.c:5732 [inline] netif_receive_skb+0x58/0x660 net/core/dev.c:5791 tun_rx_batched+0x3ee/0x980 drivers/net/tun.c:1555 tun_get_user+0x53af/0x66d0 drivers/net/tun.c:2002 tun_chr_write_iter+0x3af/0x5d0 drivers/net/tun.c:2048 call_write_iter include/linux/fs.h:2084 [inline] new_sync_write fs/read_write.c:497 [inline] vfs_write+0x786/0x1200 fs/read_write.c:590 ksys_write+0x20f/0x4c0 fs/read_write.c:643 __do_sys_write fs/read_write.c:655 [inline] __se_sys_write fs/read_write.c:652 [inline] __x64_sys_write+0x93/0xd0 fs/read_write.c:652 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0x6d/0x140 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x63/0x6b Uninit was created at: slab_post_alloc_hook+0x129/0xa70 mm/slab.h:768 slab_alloc_node mm/slub.c:3478 [inline] kmem_cache_alloc_node+0x5e9/0xb10 mm/slub.c:3523 kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:560 __alloc_skb+0x318/0x740 net/core/skbuff.c:651 alloc_skb include/linux/skbuff.h:1286 [inline] alloc_skb_with_frags+0xc8/0xbd0 net/core/skbuff.c:6334 sock_alloc_send_pskb+0xa80/0xbf0 net/core/sock.c:2787 tun_alloc_skb drivers/net/tun.c:1531 [inline] tun_get_user+0x1e8a/0x66d0 drivers/net/tun.c:1846 tun_chr_write_iter+0x3af/0x5d0 drivers/net/tun.c:2048 call_write_iter include/linux/fs.h:2084 [inline] new_sync_write fs/read_write.c:497 [inline] vfs_write+0x786/0x1200 fs/read_write.c:590 ksys_write+0x20f/0x4c0 fs/read_write.c:643 __do_sys_write fs/read_write.c:655 [inline] __se_sys_write fs/read_write.c:652 [inline] __x64_sys_write+0x93/0xd0 fs/read_write.c:652 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0x6d/0x140 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x63/0x6b CPU: 0 PID: 5034 Comm: syz-executor331 Not tainted 6.7.0-syzkaller-00562-g9f8413c4a66f #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 11/17/2023

In the Linux kernel, the following vulnerability has been resolved: cpumap: Zero-initialise xdp_rxq_info struct before running XDP program When running an XDP program that is attached to a cpumap entry, we don't initialise the xdp_rxq_info data structure being used in the xdp_buff that backs the XDP program invocation. Tobias noticed that this leads to random values being returned as the xdp_md->rx_queue_index value for XDP programs running in a cpumap. This means we're basically returning the contents of the uninitialised memory, which is bad. Fix this by zero-initialising the rxq data structure before running the XDP program.

In the Linux kernel, the following vulnerability has been resolved: fat: fix uninitialized field in nostale filehandles When fat_encode_fh_nostale() encodes file handle without a parent it stores only first 10 bytes of the file handle. However the length of the file handle must be a multiple of 4 so the file handle is actually 12 bytes long and the last two bytes remain uninitialized. This is not great at we potentially leak uninitialized information with the handle to userspace. Properly initialize the full handle length.

In the Linux kernel, the following vulnerability has been resolved: do_sys_name_to_handle(): use kzalloc() to fix kernel-infoleak syzbot identified a kernel information leak vulnerability in do_sys_name_to_handle() and issued the following report [1]. [1] "BUG: KMSAN: kernel-infoleak in instrument_copy_to_user include/linux/instrumented.h:114 [inline] BUG: KMSAN: kernel-infoleak in _copy_to_user+0xbc/0x100 lib/usercopy.c:40 instrument_copy_to_user include/linux/instrumented.h:114 [inline] _copy_to_user+0xbc/0x100 lib/usercopy.c:40 copy_to_user include/linux/uaccess.h:191 [inline] do_sys_name_to_handle fs/fhandle.c:73 [inline] __do_sys_name_to_handle_at fs/fhandle.c:112 [inline] __se_sys_name_to_handle_at+0x949/0xb10 fs/fhandle.c:94 __x64_sys_name_to_handle_at+0xe4/0x140 fs/fhandle.c:94 ... Uninit was created at: slab_post_alloc_hook+0x129/0xa70 mm/slab.h:768 slab_alloc_node mm/slub.c:3478 [inline] __kmem_cache_alloc_node+0x5c9/0x970 mm/slub.c:3517 __do_kmalloc_node mm/slab_common.c:1006 [inline] __kmalloc+0x121/0x3c0 mm/slab_common.c:1020 kmalloc include/linux/slab.h:604 [inline] do_sys_name_to_handle fs/fhandle.c:39 [inline] __do_sys_name_to_handle_at fs/fhandle.c:112 [inline] __se_sys_name_to_handle_at+0x441/0xb10 fs/fhandle.c:94 __x64_sys_name_to_handle_at+0xe4/0x140 fs/fhandle.c:94 ... Bytes 18-19 of 20 are uninitialized Memory access of size 20 starts at ffff888128a46380 Data copied to user address 0000000020000240" Per Chuck Lever's suggestion, use kzalloc() instead of kmalloc() to solve the problem.

In the Linux kernel, the following vulnerability has been resolved: iio: adc: ad4130: zero-initialize clock init data The clk_init_data struct does not have all its members initialized, causing issues when trying to expose the internal clock on the CLK pin. Fix this by zero-initializing the clk_init_data struct.

In the Linux kernel, the following vulnerability has been resolved: netlink: add nla be16/32 types to minlen array BUG: KMSAN: uninit-value in nla_validate_range_unsigned lib/nlattr.c:222 [inline] BUG: KMSAN: uninit-value in nla_validate_int_range lib/nlattr.c:336 [inline] BUG: KMSAN: uninit-value in validate_nla lib/nlattr.c:575 [inline] BUG: KMSAN: uninit-value in __nla_validate_parse+0x2e20/0x45c0 lib/nlattr.c:631 nla_validate_range_unsigned lib/nlattr.c:222 [inline] nla_validate_int_range lib/nlattr.c:336 [inline] validate_nla lib/nlattr.c:575 [inline] ... The message in question matches this policy: [NFTA_TARGET_REV] = NLA_POLICY_MAX(NLA_BE32, 255), but because NLA_BE32 size in minlen array is 0, the validation code will read past the malformed (too small) attribute. Note: Other attributes, e.g. BITFIELD32, SINT, UINT.. are also missing: those likely should be added too.

In the Linux kernel, the following vulnerability has been resolved: geneve: make sure to pull inner header in geneve_rx() syzbot triggered a bug in geneve_rx() [1] Issue is similar to the one I fixed in commit 8d975c15c0cd ("ip6_tunnel: make sure to pull inner header in __ip6_tnl_rcv()") We have to save skb->network_header in a temporary variable in order to be able to recompute the network_header pointer after a pskb_inet_may_pull() call. pskb_inet_may_pull() makes sure the needed headers are in skb->head. [1] BUG: KMSAN: uninit-value in IP_ECN_decapsulate include/net/inet_ecn.h:302 [inline] BUG: KMSAN: uninit-value in geneve_rx drivers/net/geneve.c:279 [inline] BUG: KMSAN: uninit-value in geneve_udp_encap_recv+0x36f9/0x3c10 drivers/net/geneve.c:391 IP_ECN_decapsulate include/net/inet_ecn.h:302 [inline] geneve_rx drivers/net/geneve.c:279 [inline] geneve_udp_encap_recv+0x36f9/0x3c10 drivers/net/geneve.c:391 udp_queue_rcv_one_skb+0x1d39/0x1f20 net/ipv4/udp.c:2108 udp_queue_rcv_skb+0x6ae/0x6e0 net/ipv4/udp.c:2186 udp_unicast_rcv_skb+0x184/0x4b0 net/ipv4/udp.c:2346 __udp4_lib_rcv+0x1c6b/0x3010 net/ipv4/udp.c:2422 udp_rcv+0x7d/0xa0 net/ipv4/udp.c:2604 ip_protocol_deliver_rcu+0x264/0x1300 net/ipv4/ip_input.c:205 ip_local_deliver_finish+0x2b8/0x440 net/ipv4/ip_input.c:233 NF_HOOK include/linux/netfilter.h:314 [inline] ip_local_deliver+0x21f/0x490 net/ipv4/ip_input.c:254 dst_input include/net/dst.h:461 [inline] ip_rcv_finish net/ipv4/ip_input.c:449 [inline] NF_HOOK include/linux/netfilter.h:314 [inline] ip_rcv+0x46f/0x760 net/ipv4/ip_input.c:569 __netif_receive_skb_one_core net/core/dev.c:5534 [inline] __netif_receive_skb+0x1a6/0x5a0 net/core/dev.c:5648 process_backlog+0x480/0x8b0 net/core/dev.c:5976 __napi_poll+0xe3/0x980 net/core/dev.c:6576 napi_poll net/core/dev.c:6645 [inline] net_rx_action+0x8b8/0x1870 net/core/dev.c:6778 __do_softirq+0x1b7/0x7c5 kernel/softirq.c:553 do_softirq+0x9a/0xf0 kernel/softirq.c:454 __local_bh_enable_ip+0x9b/0xa0 kernel/softirq.c:381 local_bh_enable include/linux/bottom_half.h:33 [inline] rcu_read_unlock_bh include/linux/rcupdate.h:820 [inline] __dev_queue_xmit+0x2768/0x51c0 net/core/dev.c:4378 dev_queue_xmit include/linux/netdevice.h:3171 [inline] packet_xmit+0x9c/0x6b0 net/packet/af_packet.c:276 packet_snd net/packet/af_packet.c:3081 [inline] packet_sendmsg+0x8aef/0x9f10 net/packet/af_packet.c:3113 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg net/socket.c:745 [inline] __sys_sendto+0x735/0xa10 net/socket.c:2191 __do_sys_sendto net/socket.c:2203 [inline] __se_sys_sendto net/socket.c:2199 [inline] __x64_sys_sendto+0x125/0x1c0 net/socket.c:2199 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcf/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x63/0x6b Uninit was created at: slab_post_alloc_hook mm/slub.c:3819 [inline] slab_alloc_node mm/slub.c:3860 [inline] kmem_cache_alloc_node+0x5cb/0xbc0 mm/slub.c:3903 kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:560 __alloc_skb+0x352/0x790 net/core/skbuff.c:651 alloc_skb include/linux/skbuff.h:1296 [inline] alloc_skb_with_frags+0xc8/0xbd0 net/core/skbuff.c:6394 sock_alloc_send_pskb+0xa80/0xbf0 net/core/sock.c:2783 packet_alloc_skb net/packet/af_packet.c:2930 [inline] packet_snd net/packet/af_packet.c:3024 [inline] packet_sendmsg+0x70c2/0x9f10 net/packet/af_packet.c:3113 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg net/socket.c:745 [inline] __sys_sendto+0x735/0xa10 net/socket.c:2191 __do_sys_sendto net/socket.c:2203 [inline] __se_sys_sendto net/socket.c:2199 [inline] __x64_sys_sendto+0x125/0x1c0 net/socket.c:2199 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcf/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x63/0x6b

In the Linux kernel, the following vulnerability has been resolved: media: v4l2-core: explicitly clear ioctl input data As seen from a recent syzbot bug report, mistakes in the compat ioctl implementation can lead to uninitialized kernel stack data getting used as input for driver ioctl handlers. The reported bug is now fixed, but it's possible that other related bugs are still present or get added in the future. As the drivers need to check user input already, the possible impact is fairly low, but it might still cause an information leak. To be on the safe side, always clear the entire ioctl buffer before calling the conversion handler functions that are meant to initialize them.

In the Linux kernel, the following vulnerability has been resolved: net: zero-initialize tc skb extension on allocation Function skb_ext_add() doesn't initialize created skb extension with any value and leaves it up to the user. However, since extension of type TC_SKB_EXT originally contained only single value tc_skb_ext->chain its users used to just assign the chain value without setting whole extension memory to zero first. This assumption changed when TC_SKB_EXT extension was extended with additional fields but not all users were updated to initialize the new fields which leads to use of uninitialized memory afterwards. UBSAN log: [ 778.299821] UBSAN: invalid-load in net/openvswitch/flow.c:899:28 [ 778.301495] load of value 107 is not a valid value for type '_Bool' [ 778.303215] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.12.0-rc7+ #2 [ 778.304933] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 [ 778.307901] Call Trace: [ 778.308680] <IRQ> [ 778.309358] dump_stack+0xbb/0x107 [ 778.310307] ubsan_epilogue+0x5/0x40 [ 778.311167] __ubsan_handle_load_invalid_value.cold+0x43/0x48 [ 778.312454] ? memset+0x20/0x40 [ 778.313230] ovs_flow_key_extract.cold+0xf/0x14 [openvswitch] [ 778.314532] ovs_vport_receive+0x19e/0x2e0 [openvswitch] [ 778.315749] ? ovs_vport_find_upcall_portid+0x330/0x330 [openvswitch] [ 778.317188] ? create_prof_cpu_mask+0x20/0x20 [ 778.318220] ? arch_stack_walk+0x82/0xf0 [ 778.319153] ? secondary_startup_64_no_verify+0xb0/0xbb [ 778.320399] ? stack_trace_save+0x91/0xc0 [ 778.321362] ? stack_trace_consume_entry+0x160/0x160 [ 778.322517] ? lock_release+0x52e/0x760 [ 778.323444] netdev_frame_hook+0x323/0x610 [openvswitch] [ 778.324668] ? ovs_netdev_get_vport+0xe0/0xe0 [openvswitch] [ 778.325950] __netif_receive_skb_core+0x771/0x2db0 [ 778.327067] ? lock_downgrade+0x6e0/0x6f0 [ 778.328021] ? lock_acquire+0x565/0x720 [ 778.328940] ? generic_xdp_tx+0x4f0/0x4f0 [ 778.329902] ? inet_gro_receive+0x2a7/0x10a0 [ 778.330914] ? lock_downgrade+0x6f0/0x6f0 [ 778.331867] ? udp4_gro_receive+0x4c4/0x13e0 [ 778.332876] ? lock_release+0x52e/0x760 [ 778.333808] ? dev_gro_receive+0xcc8/0x2380 [ 778.334810] ? lock_downgrade+0x6f0/0x6f0 [ 778.335769] __netif_receive_skb_list_core+0x295/0x820 [ 778.336955] ? process_backlog+0x780/0x780 [ 778.337941] ? mlx5e_rep_tc_netdevice_event_unregister+0x20/0x20 [mlx5_core] [ 778.339613] ? seqcount_lockdep_reader_access.constprop.0+0xa7/0xc0 [ 778.341033] ? kvm_clock_get_cycles+0x14/0x20 [ 778.342072] netif_receive_skb_list_internal+0x5f5/0xcb0 [ 778.343288] ? __kasan_kmalloc+0x7a/0x90 [ 778.344234] ? mlx5e_handle_rx_cqe_mpwrq+0x9e0/0x9e0 [mlx5_core] [ 778.345676] ? mlx5e_xmit_xdp_frame_mpwqe+0x14d0/0x14d0 [mlx5_core] [ 778.347140] ? __netif_receive_skb_list_core+0x820/0x820 [ 778.348351] ? mlx5e_post_rx_mpwqes+0xa6/0x25d0 [mlx5_core] [ 778.349688] ? napi_gro_flush+0x26c/0x3c0 [ 778.350641] napi_complete_done+0x188/0x6b0 [ 778.351627] mlx5e_napi_poll+0x373/0x1b80 [mlx5_core] [ 778.352853] __napi_poll+0x9f/0x510 [ 778.353704] ? mlx5_flow_namespace_set_mode+0x260/0x260 [mlx5_core] [ 778.355158] net_rx_action+0x34c/0xa40 [ 778.356060] ? napi_threaded_poll+0x3d0/0x3d0 [ 778.357083] ? sched_clock_cpu+0x18/0x190 [ 778.358041] ? __common_interrupt+0x8e/0x1a0 [ 778.359045] __do_softirq+0x1ce/0x984 [ 778.359938] __irq_exit_rcu+0x137/0x1d0 [ 778.360865] irq_exit_rcu+0xa/0x20 [ 778.361708] common_interrupt+0x80/0xa0 [ 778.362640] </IRQ> [ 778.363212] asm_common_interrupt+0x1e/0x40 [ 778.364204] RIP: 0010:native_safe_halt+0xe/0x10 [ 778.365273] Code: 4f ff ff ff 4c 89 e7 e8 50 3f 40 fe e9 dc fe ff ff 48 89 df e8 43 3f 40 fe eb 90 cc e9 07 00 00 00 0f 00 2d 74 05 62 00 fb f4 <c3> 90 e9 07 00 00 00 0f 00 2d 64 05 62 00 f4 c3 cc cc 0f 1f 44 00 [ 778.369355] RSP: 0018:ffffffff84407e48 EFLAGS: 00000246 [ 778.370570] RAX ---truncated---

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: Initialize allocated memory before use KMSAN reports: Multiple uninitialized values detected: - KMSAN: uninit-value in ntfs_read_hdr (3) - KMSAN: uninit-value in bcmp (3) Memory is allocated by __getname(), which is a wrapper for kmem_cache_alloc(). This memory is used before being properly cleared. Change kmem_cache_alloc() to kmem_cache_zalloc() to properly allocate and clear memory before use.

In the Linux kernel, the following vulnerability has been resolved: netfilter: nfnetlink_log: fix uninitialized padding leak in NFULA_PAYLOAD __build_packet_message() manually constructs the NFULA_PAYLOAD netlink attribute using skb_put() and skb_copy_bits(), bypassing the standard nla_reserve()/nla_put() helpers. While nla_total_size(data_len) bytes are allocated (including NLA alignment padding), only data_len bytes of actual packet data are copied. The trailing nla_padlen(data_len) bytes (1-3 when data_len is not 4-byte aligned) are never initialized, leaking stale heap contents to userspace via the NFLOG netlink socket. Replace the manual attribute construction with nla_reserve(), which handles the tailroom check, header setup, and padding zeroing via __nla_reserve(). The subsequent skb_copy_bits() fills in the payload data on top of the properly initialized attribute.

In the Linux kernel, the following vulnerability has been resolved: bnge: return after auxiliary_device_uninit() in error path When auxiliary_device_add() fails, the error block calls auxiliary_device_uninit() but does not return. The uninit drops the last reference and synchronously runs bnge_aux_dev_release(), which sets bd->auxr_dev = NULL and frees the underlying object. The subsequent bd->auxr_dev->net = bd->netdev then dereferences NULL, which is not a good thing to have happen when trying to clean up from an error. Add the missing return, as the auxiliary bus documentation states is a requirement (seems that LLM tools read documentation better than humans do...)

In the Linux kernel, the following vulnerability has been resolved: RDMA/irdma: Initialize free_qp completion before using it In irdma_create_qp, if ib_copy_to_udata fails, it will call irdma_destroy_qp to clean up which will attempt to wait on the free_qp completion, which is not initialized yet. Fix this by initializing the completion before the ib_copy_to_udata call.

In the Linux kernel, the following vulnerability has been resolved: team: better TEAM_OPTION_TYPE_STRING validation syzbot reported following splat [1] Make sure user-provided data contains one nul byte. [1] BUG: KMSAN: uninit-value in string_nocheck lib/vsprintf.c:633 [inline] BUG: KMSAN: uninit-value in string+0x3ec/0x5f0 lib/vsprintf.c:714 string_nocheck lib/vsprintf.c:633 [inline] string+0x3ec/0x5f0 lib/vsprintf.c:714 vsnprintf+0xa5d/0x1960 lib/vsprintf.c:2843 __request_module+0x252/0x9f0 kernel/module/kmod.c:149 team_mode_get drivers/net/team/team_core.c:480 [inline] team_change_mode drivers/net/team/team_core.c:607 [inline] team_mode_option_set+0x437/0x970 drivers/net/team/team_core.c:1401 team_option_set drivers/net/team/team_core.c:375 [inline] team_nl_options_set_doit+0x1339/0x1f90 drivers/net/team/team_core.c:2662 genl_family_rcv_msg_doit net/netlink/genetlink.c:1115 [inline] genl_family_rcv_msg net/netlink/genetlink.c:1195 [inline] genl_rcv_msg+0x1214/0x12c0 net/netlink/genetlink.c:1210 netlink_rcv_skb+0x375/0x650 net/netlink/af_netlink.c:2543 genl_rcv+0x40/0x60 net/netlink/genetlink.c:1219 netlink_unicast_kernel net/netlink/af_netlink.c:1322 [inline] netlink_unicast+0xf52/0x1260 net/netlink/af_netlink.c:1348 netlink_sendmsg+0x10da/0x11e0 net/netlink/af_netlink.c:1892 sock_sendmsg_nosec net/socket.c:718 [inline] __sock_sendmsg+0x30f/0x380 net/socket.c:733 ____sys_sendmsg+0x877/0xb60 net/socket.c:2573 ___sys_sendmsg+0x28d/0x3c0 net/socket.c:2627 __sys_sendmsg net/socket.c:2659 [inline] __do_sys_sendmsg net/socket.c:2664 [inline] __se_sys_sendmsg net/socket.c:2662 [inline] __x64_sys_sendmsg+0x212/0x3c0 net/socket.c:2662 x64_sys_call+0x2ed6/0x3c30 arch/x86/include/generated/asm/syscalls_64.h:47 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f

In the Linux kernel, the following vulnerability has been resolved: net: usb: smsc75xx: Fix uninit-value access in __smsc75xx_read_reg syzbot reported the following uninit-value access issue: ===================================================== BUG: KMSAN: uninit-value in smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:975 [inline] BUG: KMSAN: uninit-value in smsc75xx_bind+0x5c9/0x11e0 drivers/net/usb/smsc75xx.c:1482 CPU: 0 PID: 8696 Comm: kworker/0:3 Not tainted 5.8.0-rc5-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Workqueue: usb_hub_wq hub_event Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x21c/0x280 lib/dump_stack.c:118 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:121 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215 smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:975 [inline] smsc75xx_bind+0x5c9/0x11e0 drivers/net/usb/smsc75xx.c:1482 usbnet_probe+0x1152/0x3f90 drivers/net/usb/usbnet.c:1737 usb_probe_interface+0xece/0x1550 drivers/usb/core/driver.c:374 really_probe+0xf20/0x20b0 drivers/base/dd.c:529 driver_probe_device+0x293/0x390 drivers/base/dd.c:701 __device_attach_driver+0x63f/0x830 drivers/base/dd.c:807 bus_for_each_drv+0x2ca/0x3f0 drivers/base/bus.c:431 __device_attach+0x4e2/0x7f0 drivers/base/dd.c:873 device_initial_probe+0x4a/0x60 drivers/base/dd.c:920 bus_probe_device+0x177/0x3d0 drivers/base/bus.c:491 device_add+0x3b0e/0x40d0 drivers/base/core.c:2680 usb_set_configuration+0x380f/0x3f10 drivers/usb/core/message.c:2032 usb_generic_driver_probe+0x138/0x300 drivers/usb/core/generic.c:241 usb_probe_device+0x311/0x490 drivers/usb/core/driver.c:272 really_probe+0xf20/0x20b0 drivers/base/dd.c:529 driver_probe_device+0x293/0x390 drivers/base/dd.c:701 __device_attach_driver+0x63f/0x830 drivers/base/dd.c:807 bus_for_each_drv+0x2ca/0x3f0 drivers/base/bus.c:431 __device_attach+0x4e2/0x7f0 drivers/base/dd.c:873 device_initial_probe+0x4a/0x60 drivers/base/dd.c:920 bus_probe_device+0x177/0x3d0 drivers/base/bus.c:491 device_add+0x3b0e/0x40d0 drivers/base/core.c:2680 usb_new_device+0x1bd4/0x2a30 drivers/usb/core/hub.c:2554 hub_port_connect drivers/usb/core/hub.c:5208 [inline] hub_port_connect_change drivers/usb/core/hub.c:5348 [inline] port_event drivers/usb/core/hub.c:5494 [inline] hub_event+0x5e7b/0x8a70 drivers/usb/core/hub.c:5576 process_one_work+0x1688/0x2140 kernel/workqueue.c:2269 worker_thread+0x10bc/0x2730 kernel/workqueue.c:2415 kthread+0x551/0x590 kernel/kthread.c:292 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:293 Local variable ----buf.i87@smsc75xx_bind created at: __smsc75xx_read_reg drivers/net/usb/smsc75xx.c:83 [inline] smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:968 [inline] smsc75xx_bind+0x485/0x11e0 drivers/net/usb/smsc75xx.c:1482 __smsc75xx_read_reg drivers/net/usb/smsc75xx.c:83 [inline] smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:968 [inline] smsc75xx_bind+0x485/0x11e0 drivers/net/usb/smsc75xx.c:1482 This issue is caused because usbnet_read_cmd() reads less bytes than requested (zero byte in the reproducer). In this case, 'buf' is not properly filled. This patch fixes the issue by returning -ENODATA if usbnet_read_cmd() reads less bytes than requested.