In the Linux kernel, the following vulnerability has been resolved: mm/vmalloc: fix data race in show_numa_info() The following data-race was found in show_numa_info(): ================================================================== BUG: KCSAN: data-race in vmalloc_info_show / vmalloc_info_show read to 0xffff88800971fe30 of 4 bytes by task 8289 on cpu 0: show_numa_info mm/vmalloc.c:4936 [inline] vmalloc_info_show+0x5a8/0x7e0 mm/vmalloc.c:5016 seq_read_iter+0x373/0xb40 fs/seq_file.c:230 proc_reg_read_iter+0x11e/0x170 fs/proc/inode.c:299 .... write to 0xffff88800971fe30 of 4 bytes by task 8287 on cpu 1: show_numa_info mm/vmalloc.c:4934 [inline] vmalloc_info_show+0x38f/0x7e0 mm/vmalloc.c:5016 seq_read_iter+0x373/0xb40 fs/seq_file.c:230 proc_reg_read_iter+0x11e/0x170 fs/proc/inode.c:299 .... value changed: 0x0000008f -> 0x00000000 ================================================================== According to this report,there is a read/write data-race because m->private is accessible to multiple CPUs. To fix this, instead of allocating the heap in proc_vmalloc_init() and passing the heap address to m->private, vmalloc_info_show() should allocate the heap.

In the Linux kernel, the following vulnerability has been resolved: mm/page_alloc: fix race condition in unaccepted memory handling The page allocator tracks the number of zones that have unaccepted memory using static_branch_enc/dec() and uses that static branch in hot paths to determine if it needs to deal with unaccepted memory. Borislav and Thomas pointed out that the tracking is racy: operations on static_branch are not serialized against adding/removing unaccepted pages to/from the zone. Sanity checks inside static_branch machinery detects it: WARNING: CPU: 0 PID: 10 at kernel/jump_label.c:276 __static_key_slow_dec_cpuslocked+0x8e/0xa0 The comment around the WARN() explains the problem: /* * Warn about the '-1' case though; since that means a * decrement is concurrent with a first (0->1) increment. IOW * people are trying to disable something that wasn't yet fully * enabled. This suggests an ordering problem on the user side. */ The effect of this static_branch optimization is only visible on microbenchmark. Instead of adding more complexity around it, remove it altogether.

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: u_serial: Fix race condition in TTY wakeup A race condition occurs when gs_start_io() calls either gs_start_rx() or gs_start_tx(), as those functions briefly drop the port_lock for usb_ep_queue(). This allows gs_close() and gserial_disconnect() to clear port.tty and port_usb, respectively. Use the null-safe TTY Port helper function to wake up TTY. Example CPU1: CPU2: gserial_connect() // lock gs_close() // await lock gs_start_rx() // unlock usb_ep_queue() gs_close() // lock, reset port.tty and unlock gs_start_rx() // lock tty_wakeup() // NPE

In the Linux kernel, the following vulnerability has been resolved: ublk: fix race between io_uring_cmd_complete_in_task and ublk_cancel_cmd ublk_cancel_cmd() calls io_uring_cmd_done() to complete uring_cmd, but we may have scheduled task work via io_uring_cmd_complete_in_task() for dispatching request, then kernel crash can be triggered. Fix it by not trying to canceling the command if ublk block request is started.

In the Linux kernel, the following vulnerability has been resolved: USB: wdm: close race between wdm_open and wdm_wwan_port_stop Clearing WDM_WWAN_IN_USE must be the last action or we can open a chardev whose URBs are still poisoned

In the Linux kernel, the following vulnerability has been resolved: nfsd: avoid ref leak in nfsd_open_local_fh() If two calls to nfsd_open_local_fh() race and both successfully call nfsd_file_acquire_local(), they will both get an extra reference to the net to accompany the file reference stored in *pnf. One of them will fail to store (using xchg()) the file reference in *pnf and will drop that reference but WON'T drop the accompanying reference to the net. This leak means that when the nfs server is shut down it will hang in nfsd_shutdown_net() waiting for &nn->nfsd_net_free_done. This patch adds the missing nfsd_net_put().

In the Linux kernel, the following vulnerability has been resolved: mm: userfaultfd: fix race of userfaultfd_move and swap cache This commit fixes two kinds of races, they may have different results: Barry reported a BUG_ON in commit c50f8e6053b0, we may see the same BUG_ON if the filemap lookup returned NULL and folio is added to swap cache after that. If another kind of race is triggered (folio changed after lookup) we may see RSS counter is corrupted: [ 406.893936] BUG: Bad rss-counter state mm:ffff0000c5a9ddc0 type:MM_ANONPAGES val:-1 [ 406.894071] BUG: Bad rss-counter state mm:ffff0000c5a9ddc0 type:MM_SHMEMPAGES val:1 Because the folio is being accounted to the wrong VMA. I'm not sure if there will be any data corruption though, seems no. The issues above are critical already. On seeing a swap entry PTE, userfaultfd_move does a lockless swap cache lookup, and tries to move the found folio to the faulting vma. Currently, it relies on checking the PTE value to ensure that the moved folio still belongs to the src swap entry and that no new folio has been added to the swap cache, which turns out to be unreliable. While working and reviewing the swap table series with Barry, following existing races are observed and reproduced [1]: In the example below, move_pages_pte is moving src_pte to dst_pte, where src_pte is a swap entry PTE holding swap entry S1, and S1 is not in the swap cache: CPU1 CPU2 userfaultfd_move move_pages_pte() entry = pte_to_swp_entry(orig_src_pte); // Here it got entry = S1 ... < interrupted> ... <swapin src_pte, alloc and use folio A> // folio A is a new allocated folio // and get installed into src_pte <frees swap entry S1> // src_pte now points to folio A, S1 // has swap count == 0, it can be freed // by folio_swap_swap or swap // allocator's reclaim. <try to swap out another folio B> // folio B is a folio in another VMA. <put folio B to swap cache using S1 > // S1 is freed, folio B can use it // for swap out with no problem. ... folio = filemap_get_folio(S1) // Got folio B here !!! ... < interrupted again> ... <swapin folio B and free S1> // Now S1 is free to be used again. <swapout src_pte & folio A using S1> // Now src_pte is a swap entry PTE // holding S1 again. folio_trylock(folio) move_swap_pte double_pt_lock is_pte_pages_stable // Check passed because src_pte == S1 folio_move_anon_rmap(...) // Moved invalid folio B here !!! The race window is very short and requires multiple collisions of multiple rare events, so it's very unlikely to happen, but with a deliberately constructed reproducer and increased time window, it can be reproduced easily. This can be fixed by checking if the folio returned by filemap is the valid swap cache folio after acquiring the folio lock. Another similar race is possible: filemap_get_folio may return NULL, but folio (A) could be swapped in and then swapped out again using the same swap entry after the lookup. In such a case, folio (A) may remain in the swap cache, so it must be moved too: CPU1 CPU2 userfaultfd_move move_pages_pte() entry = pte_to_swp_entry(orig_src_pte); // Here it got entry = S1, and S1 is not in swap cache folio = filemap_get ---truncated---

In the Linux kernel, the following vulnerability has been resolved: fs/fhandle.c: fix a race in call of has_locked_children() may_decode_fh() is calling has_locked_children() while holding no locks. That's an oopsable race... The rest of the callers are safe since they are holding namespace_sem and are guaranteed a positive refcount on the mount in question. Rename the current has_locked_children() to __has_locked_children(), make it static and switch the fs/namespace.c users to it. Make has_locked_children() a wrapper for __has_locked_children(), calling the latter under read_seqlock_excl(&mount_lock).

In the Linux kernel, the following vulnerability has been resolved: ALSA: pcm: Fix race of buffer access at PCM OSS layer The PCM OSS layer tries to clear the buffer with the silence data at initialization (or reconfiguration) of a stream with the explicit call of snd_pcm_format_set_silence() with runtime->dma_area. But this may lead to a UAF because the accessed runtime->dma_area might be freed concurrently, as it's performed outside the PCM ops. For avoiding it, move the code into the PCM core and perform it inside the buffer access lock, so that it won't be changed during the operation.

In the Linux kernel, the following vulnerability has been resolved: virtio_ring: Fix data race by tagging event_triggered as racy for KCSAN syzbot reports a data-race when accessing the event_triggered, here is the simplified stack when the issue occurred: ================================================================== BUG: KCSAN: data-race in virtqueue_disable_cb / virtqueue_enable_cb_delayed write to 0xffff8881025bc452 of 1 bytes by task 3288 on cpu 0: virtqueue_enable_cb_delayed+0x42/0x3c0 drivers/virtio/virtio_ring.c:2653 start_xmit+0x230/0x1310 drivers/net/virtio_net.c:3264 __netdev_start_xmit include/linux/netdevice.h:5151 [inline] netdev_start_xmit include/linux/netdevice.h:5160 [inline] xmit_one net/core/dev.c:3800 [inline] read to 0xffff8881025bc452 of 1 bytes by interrupt on cpu 1: virtqueue_disable_cb_split drivers/virtio/virtio_ring.c:880 [inline] virtqueue_disable_cb+0x92/0x180 drivers/virtio/virtio_ring.c:2566 skb_xmit_done+0x5f/0x140 drivers/net/virtio_net.c:777 vring_interrupt+0x161/0x190 drivers/virtio/virtio_ring.c:2715 __handle_irq_event_percpu+0x95/0x490 kernel/irq/handle.c:158 handle_irq_event_percpu kernel/irq/handle.c:193 [inline] value changed: 0x01 -> 0x00 ================================================================== When the data race occurs, the function virtqueue_enable_cb_delayed() sets event_triggered to false, and virtqueue_disable_cb_split/packed() reads it as false due to the race condition. Since event_triggered is an unreliable hint used for optimization, this should only cause the driver temporarily suggest that the device not send an interrupt notification when the event index is used. Fix this KCSAN reported data-race issue by explicitly tagging the access as data_racy.

An issue was discovered in drivers/bluetooth/hci_ldisc.c in the Linux kernel 6.2. In hci_uart_tty_ioctl, there is a race condition between HCIUARTSETPROTO and HCIUARTGETPROTO. HCI_UART_PROTO_SET is set before hu->proto is set. A NULL pointer dereference may occur.

In the Linux kernel, the following vulnerability has been resolved: NFSD: fix race between nfsd registration and exports_proc As of now nfsd calls create_proc_exports_entry() at start of init_nfsd and cleanup by remove_proc_entry() at last of exit_nfsd. Which causes kernel OOPs if there is race between below 2 operations: (i) exportfs -r (ii) mount -t nfsd none /proc/fs/nfsd for 5.4 kernel ARM64: CPU 1: el1_irq+0xbc/0x180 arch_counter_get_cntvct+0x14/0x18 running_clock+0xc/0x18 preempt_count_add+0x88/0x110 prep_new_page+0xb0/0x220 get_page_from_freelist+0x2d8/0x1778 __alloc_pages_nodemask+0x15c/0xef0 __vmalloc_node_range+0x28c/0x478 __vmalloc_node_flags_caller+0x8c/0xb0 kvmalloc_node+0x88/0xe0 nfsd_init_net+0x6c/0x108 [nfsd] ops_init+0x44/0x170 register_pernet_operations+0x114/0x270 register_pernet_subsys+0x34/0x50 init_nfsd+0xa8/0x718 [nfsd] do_one_initcall+0x54/0x2e0 CPU 2 : Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010 PC is at : exports_net_open+0x50/0x68 [nfsd] Call trace: exports_net_open+0x50/0x68 [nfsd] exports_proc_open+0x2c/0x38 [nfsd] proc_reg_open+0xb8/0x198 do_dentry_open+0x1c4/0x418 vfs_open+0x38/0x48 path_openat+0x28c/0xf18 do_filp_open+0x70/0xe8 do_sys_open+0x154/0x248 Sometimes it crashes at exports_net_open() and sometimes cache_seq_next_rcu(). and same is happening on latest 6.14 kernel as well: [ 0.000000] Linux version 6.14.0-rc5-next-20250304-dirty ... [ 285.455918] Unable to handle kernel paging request at virtual address 00001f4800001f48 ... [ 285.464902] pc : cache_seq_next_rcu+0x78/0xa4 ... [ 285.469695] Call trace: [ 285.470083] cache_seq_next_rcu+0x78/0xa4 (P) [ 285.470488] seq_read+0xe0/0x11c [ 285.470675] proc_reg_read+0x9c/0xf0 [ 285.470874] vfs_read+0xc4/0x2fc [ 285.471057] ksys_read+0x6c/0xf4 [ 285.471231] __arm64_sys_read+0x1c/0x28 [ 285.471428] invoke_syscall+0x44/0x100 [ 285.471633] el0_svc_common.constprop.0+0x40/0xe0 [ 285.471870] do_el0_svc_compat+0x1c/0x34 [ 285.472073] el0_svc_compat+0x2c/0x80 [ 285.472265] el0t_32_sync_handler+0x90/0x140 [ 285.472473] el0t_32_sync+0x19c/0x1a0 [ 285.472887] Code: f9400885 93407c23 937d7c27 11000421 (f86378a3) [ 285.473422] ---[ end trace 0000000000000000 ]--- It reproduced simply with below script: while [ 1 ] do /exportfs -r done & while [ 1 ] do insmod /nfsd.ko mount -t nfsd none /proc/fs/nfsd umount /proc/fs/nfsd rmmod nfsd done & So exporting interfaces to user space shall be done at last and cleanup at first place. With change there is no Kernel OOPs.

A flaw was found in the subsequent get_user_pages_fast in the Linux kernel’s interface for symmetric key cipher algorithms in the skcipher_recvmsg of crypto/algif_skcipher.c function. This flaw allows a local user to crash the system.

In the Linux kernel, the following vulnerability has been resolved: fix a couple of races in MNT_TREE_BENEATH handling by do_move_mount() Normally do_lock_mount(path, _) is locking a mountpoint pinned by *path and at the time when matching unlock_mount() unlocks that location it is still pinned by the same thing. Unfortunately, for 'beneath' case it's no longer that simple - the object being locked is not the one *path points to. It's the mountpoint of path->mnt. The thing is, without sufficient locking ->mnt_parent may change under us and none of the locks are held at that point. The rules are * mount_lock stabilizes m->mnt_parent for any mount m. * namespace_sem stabilizes m->mnt_parent, provided that m is mounted. * if either of the above holds and refcount of m is positive, we are guaranteed the same for refcount of m->mnt_parent. namespace_sem nests inside inode_lock(), so do_lock_mount() has to take inode_lock() before grabbing namespace_sem. It does recheck that path->mnt is still mounted in the same place after getting namespace_sem, and it does take care to pin the dentry. It is needed, since otherwise we might end up with racing mount --move (or umount) happening while we were getting locks; in that case dentry would no longer be a mountpoint and could've been evicted on memory pressure along with its inode - not something you want when grabbing lock on that inode. However, pinning a dentry is not enough - the matching mount is also pinned only by the fact that path->mnt is mounted on top it and at that point we are not holding any locks whatsoever, so the same kind of races could end up with all references to that mount gone just as we are about to enter inode_lock(). If that happens, we are left with filesystem being shut down while we are holding a dentry reference on it; results are not pretty. What we need to do is grab both dentry and mount at the same time; that makes inode_lock() safe *and* avoids the problem with fs getting shut down under us. After taking namespace_sem we verify that path->mnt is still mounted (which stabilizes its ->mnt_parent) and check that it's still mounted at the same place. From that point on to the matching namespace_unlock() we are guaranteed that mount/dentry pair we'd grabbed are also pinned by being the mountpoint of path->mnt, so we can quietly drop both the dentry reference (as the current code does) and mnt one - it's OK to do under namespace_sem, since we are not dropping the final refs. That solves the problem on do_lock_mount() side; unlock_mount() also has one, since dentry is guaranteed to stay pinned only until the namespace_unlock(). That's easy to fix - just have inode_unlock() done earlier, while it's still pinned by mp->m_dentry.

There is a null-pointer-dereference flaw found in f2fs_write_end_io in fs/f2fs/data.c in the Linux kernel. This flaw allows a local privileged user to cause a denial of service problem.

A race condition accessing file object in the Linux kernel OverlayFS subsystem was found in the way users do rename in specific way with OverlayFS. A local user could use this flaw to crash the system.

In the Linux kernel, the following vulnerability has been resolved: io_uring/io-wq: Use set_bit() and test_bit() at worker->flags Utilize set_bit() and test_bit() on worker->flags within io_uring/io-wq to address potential data races. The structure io_worker->flags may be accessed through various data paths, leading to concurrency issues. When KCSAN is enabled, it reveals data races occurring in io_worker_handle_work and io_wq_activate_free_worker functions. BUG: KCSAN: data-race in io_worker_handle_work / io_wq_activate_free_worker write to 0xffff8885c4246404 of 4 bytes by task 49071 on cpu 28: io_worker_handle_work (io_uring/io-wq.c:434 io_uring/io-wq.c:569) io_wq_worker (io_uring/io-wq.c:?) <snip> read to 0xffff8885c4246404 of 4 bytes by task 49024 on cpu 5: io_wq_activate_free_worker (io_uring/io-wq.c:? io_uring/io-wq.c:285) io_wq_enqueue (io_uring/io-wq.c:947) io_queue_iowq (io_uring/io_uring.c:524) io_req_task_submit (io_uring/io_uring.c:1511) io_handle_tw_list (io_uring/io_uring.c:1198) <snip> Line numbers against commit 18daea77cca6 ("Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm"). These races involve writes and reads to the same memory location by different tasks running on different CPUs. To mitigate this, refactor the code to use atomic operations such as set_bit(), test_bit(), and clear_bit() instead of basic "and" and "or" operations. This ensures thread-safe manipulation of worker flags. Also, move `create_index` to avoid holes in the structure.

Race condition in some Intel(R) Aptio* V UEFI Firmware Integrator Tools may allow an authenticated user to potentially enable denial of service via local access.

In the Linux kernel, the following vulnerability has been resolved: bus: mhi: host: Fix race between unprepare and queue_buf A client driver may use mhi_unprepare_from_transfer() to quiesce incoming data during the client driver's tear down. The client driver might also be processing data at the same time, resulting in a call to mhi_queue_buf() which will invoke mhi_gen_tre(). If mhi_gen_tre() runs after mhi_unprepare_from_transfer() has torn down the channel, a panic will occur due to an invalid dereference leading to a page fault. This occurs because mhi_gen_tre() does not verify the channel state after locking it. Fix this by having mhi_gen_tre() confirm the channel state is valid, or return error to avoid accessing deinitialized data. [mani: added stable tag]

In the Linux kernel, the following vulnerability has been resolved: af_unix: Fix data races in unix_release_sock/unix_stream_sendmsg A data-race condition has been identified in af_unix. In one data path, the write function unix_release_sock() atomically writes to sk->sk_shutdown using WRITE_ONCE. However, on the reader side, unix_stream_sendmsg() does not read it atomically. Consequently, this issue is causing the following KCSAN splat to occur: BUG: KCSAN: data-race in unix_release_sock / unix_stream_sendmsg write (marked) to 0xffff88867256ddbb of 1 bytes by task 7270 on cpu 28: unix_release_sock (net/unix/af_unix.c:640) unix_release (net/unix/af_unix.c:1050) sock_close (net/socket.c:659 net/socket.c:1421) __fput (fs/file_table.c:422) __fput_sync (fs/file_table.c:508) __se_sys_close (fs/open.c:1559 fs/open.c:1541) __x64_sys_close (fs/open.c:1541) x64_sys_call (arch/x86/entry/syscall_64.c:33) do_syscall_64 (arch/x86/entry/common.c:?) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130) read to 0xffff88867256ddbb of 1 bytes by task 989 on cpu 14: unix_stream_sendmsg (net/unix/af_unix.c:2273) __sock_sendmsg (net/socket.c:730 net/socket.c:745) ____sys_sendmsg (net/socket.c:2584) __sys_sendmmsg (net/socket.c:2638 net/socket.c:2724) __x64_sys_sendmmsg (net/socket.c:2753 net/socket.c:2750 net/socket.c:2750) x64_sys_call (arch/x86/entry/syscall_64.c:33) do_syscall_64 (arch/x86/entry/common.c:?) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130) value changed: 0x01 -> 0x03 The line numbers are related to commit dd5a440a31fa ("Linux 6.9-rc7"). Commit e1d09c2c2f57 ("af_unix: Fix data races around sk->sk_shutdown.") addressed a comparable issue in the past regarding sk->sk_shutdown. However, it overlooked resolving this particular data path. This patch only offending unix_stream_sendmsg() function, since the other reads seem to be protected by unix_state_lock() as discussed in

In the Linux kernel, the following vulnerability has been resolved: udp: Deal with race between UDP socket address change and rehash If a UDP socket changes its local address while it's receiving datagrams, as a result of connect(), there is a period during which a lookup operation might fail to find it, after the address is changed but before the secondary hash (port and address) and the four-tuple hash (local and remote ports and addresses) are updated. Secondary hash chains were introduced by commit 30fff9231fad ("udp: bind() optimisation") and, as a result, a rehash operation became needed to make a bound socket reachable again after a connect(). This operation was introduced by commit 719f835853a9 ("udp: add rehash on connect()") which isn't however a complete fix: the socket will be found once the rehashing completes, but not while it's pending. This is noticeable with a socat(1) server in UDP4-LISTEN mode, and a client sending datagrams to it. After the server receives the first datagram (cf. _xioopen_ipdgram_listen()), it issues a connect() to the address of the sender, in order to set up a directed flow. Now, if the client, running on a different CPU thread, happens to send a (subsequent) datagram while the server's socket changes its address, but is not rehashed yet, this will result in a failed lookup and a port unreachable error delivered to the client, as apparent from the following reproducer: LEN=$(($(cat /proc/sys/net/core/wmem_default) / 4)) dd if=/dev/urandom bs=1 count=${LEN} of=tmp.in while :; do taskset -c 1 socat UDP4-LISTEN:1337,null-eof OPEN:tmp.out,create,trunc & sleep 0.1 || sleep 1 taskset -c 2 socat OPEN:tmp.in UDP4:localhost:1337,shut-null wait done where the client will eventually get ECONNREFUSED on a write() (typically the second or third one of a given iteration): 2024/11/13 21:28:23 socat[46901] E write(6, 0x556db2e3c000, 8192): Connection refused This issue was first observed as a seldom failure in Podman's tests checking UDP functionality while using pasta(1) to connect the container's network namespace, which leads us to a reproducer with the lookup error resulting in an ICMP packet on a tap device: LOCAL_ADDR="$(ip -j -4 addr show|jq -rM '.[] | .addr_info[0] | select(.scope == "global").local')" while :; do ./pasta --config-net -p pasta.pcap -u 1337 socat UDP4-LISTEN:1337,null-eof OPEN:tmp.out,create,trunc & sleep 0.2 || sleep 1 socat OPEN:tmp.in UDP4:${LOCAL_ADDR}:1337,shut-null wait cmp tmp.in tmp.out done Once this fails: tmp.in tmp.out differ: char 8193, line 29 we can finally have a look at what's going on: $ tshark -r pasta.pcap 1 0.000000 :: ? ff02::16 ICMPv6 110 Multicast Listener Report Message v2 2 0.168690 88.198.0.161 ? 88.198.0.164 UDP 8234 60260 ? 1337 Len=8192 3 0.168767 88.198.0.161 ? 88.198.0.164 UDP 8234 60260 ? 1337 Len=8192 4 0.168806 88.198.0.161 ? 88.198.0.164 UDP 8234 60260 ? 1337 Len=8192 5 0.168827 c6:47:05:8d:dc:04 ? Broadcast ARP 42 Who has 88.198.0.161? Tell 88.198.0.164 6 0.168851 9a:55:9a:55:9a:55 ? c6:47:05:8d:dc:04 ARP 42 88.198.0.161 is at 9a:55:9a:55:9a:55 7 0.168875 88.198.0.161 ? 88.198.0.164 UDP 8234 60260 ? 1337 Len=8192 8 0.168896 88.198.0.164 ? 88.198.0.161 ICMP 590 Destination unreachable (Port unreachable) 9 0.168926 88.198.0.161 ? 88.198.0.164 UDP 8234 60260 ? 1337 Len=8192 10 0.168959 88.198.0.161 ? 88.198.0.164 UDP 8234 60260 ? 1337 Len=8192 11 0.168989 88.198.0.161 ? 88.198.0.164 UDP 4138 60260 ? 1337 Len=4096 12 0.169010 88.198.0.161 ? 88.198.0.164 UDP 42 60260 ? 1337 Len=0 On the third datagram received, the network namespace of the container initiates an ARP lookup to deliver the ICMP message. In another variant of this reproducer, starting the client with: strace -f pasta --config-net -u 1337 socat UDP4-LISTEN:1337,null-eof OPEN:tmp.out,create,tru ---truncated---

In the Linux kernel, the following vulnerability has been resolved: iommu/arm-smmu: Defer probe of clients after smmu device bound Null pointer dereference occurs due to a race between smmu driver probe and client driver probe, when of_dma_configure() for client is called after the iommu_device_register() for smmu driver probe has executed but before the driver_bound() for smmu driver has been called. Following is how the race occurs: T1:Smmu device probe T2: Client device probe really_probe() arm_smmu_device_probe() iommu_device_register() really_probe() platform_dma_configure() of_dma_configure() of_dma_configure_id() of_iommu_configure() iommu_probe_device() iommu_init_device() arm_smmu_probe_device() arm_smmu_get_by_fwnode() driver_find_device_by_fwnode() driver_find_device() next_device() klist_next() /* null ptr assigned to smmu */ /* null ptr dereference while smmu->streamid_mask */ driver_bound() klist_add_tail() When this null smmu pointer is dereferenced later in arm_smmu_probe_device, the device crashes. Fix this by deferring the probe of the client device until the smmu device has bound to the arm smmu driver. [will: Add comment]

In the Linux kernel, the following vulnerability has been resolved: accel/ivpu: Prevent recovery invocation during probe and resume Refactor IPC send and receive functions to allow correct handling of operations that should not trigger a recovery process. Expose ivpu_send_receive_internal(), which is now utilized by the D0i3 entry, DCT initialization, and HWS initialization functions. These functions have been modified to return error codes gracefully, rather than initiating recovery. The updated functions are invoked within ivpu_probe() and ivpu_resume(), ensuring that any errors encountered during these stages result in a proper teardown or shutdown sequence. The previous approach of triggering recovery within these functions could lead to a race condition, potentially causing undefined behavior and kernel crashes due to null pointer dereferences.

In the Linux kernel, the following vulnerability has been resolved: media: i2c: tc358743: Fix crash in the probe error path when using polling If an error occurs in the probe() function, we should remove the polling timer that was alarmed earlier, otherwise the timer is called with arguments that are already freed, which results in a crash. ------------[ cut here ]------------ WARNING: CPU: 3 PID: 0 at kernel/time/timer.c:1830 __run_timers+0x244/0x268 Modules linked in: CPU: 3 UID: 0 PID: 0 Comm: swapper/3 Not tainted 6.11.0 #226 Hardware name: Diasom DS-RK3568-SOM-EVB (DT) pstate: 804000c9 (Nzcv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : __run_timers+0x244/0x268 lr : __run_timers+0x1d4/0x268 sp : ffffff80eff2baf0 x29: ffffff80eff2bb50 x28: 7fffffffffffffff x27: ffffff80eff2bb00 x26: ffffffc080f669c0 x25: ffffff80efef6bf0 x24: ffffff80eff2bb00 x23: 0000000000000000 x22: dead000000000122 x21: 0000000000000000 x20: ffffff80efef6b80 x19: ffffff80041c8bf8 x18: ffffffffffffffff x17: ffffffc06f146000 x16: ffffff80eff27dc0 x15: 000000000000003e x14: 0000000000000000 x13: 00000000000054da x12: 0000000000000000 x11: 00000000000639c0 x10: 000000000000000c x9 : 0000000000000009 x8 : ffffff80eff2cb40 x7 : ffffff80eff2cb40 x6 : ffffff8002bee480 x5 : ffffffc080cb2220 x4 : ffffffc080cb2150 x3 : 00000000000f4240 x2 : 0000000000000102 x1 : ffffff80eff2bb00 x0 : ffffff80041c8bf0 Call trace:  __run_timers+0x244/0x268  timer_expire_remote+0x50/0x68  tmigr_handle_remote+0x388/0x39c  run_timer_softirq+0x38/0x44  handle_softirqs+0x138/0x298  __do_softirq+0x14/0x20  ____do_softirq+0x10/0x1c  call_on_irq_stack+0x24/0x4c  do_softirq_own_stack+0x1c/0x2c  irq_exit_rcu+0x9c/0xcc  el1_interrupt+0x48/0xc0  el1h_64_irq_handler+0x18/0x24  el1h_64_irq+0x7c/0x80  default_idle_call+0x34/0x68  do_idle+0x23c/0x294  cpu_startup_entry+0x38/0x3c  secondary_start_kernel+0x128/0x160  __secondary_switched+0xb8/0xbc ---[ end trace 0000000000000000 ]---

In the Linux kernel, the following vulnerability has been resolved: netfilter: ipset: Hold module reference while requesting a module User space may unload ip_set.ko while it is itself requesting a set type backend module, leading to a kernel crash. The race condition may be provoked by inserting an mdelay() right after the nfnl_unlock() call.

In the Linux kernel, the following vulnerability has been resolved: mm: revert "mm: shmem: fix data-race in shmem_getattr()" Revert d949d1d14fa2 ("mm: shmem: fix data-race in shmem_getattr()") as suggested by Chuck [1]. It is causing deadlocks when accessing tmpfs over NFS. As Hugh commented, "added just to silence a syzbot sanitizer splat: added where there has never been any practical problem".

In the Linux kernel, the following vulnerability has been resolved: nvme: tcp: avoid race between queue_lock lock and destroy Commit 76d54bf20cdc ("nvme-tcp: don't access released socket during error recovery") added a mutex_lock() call for the queue->queue_lock in nvme_tcp_get_address(). However, the mutex_lock() races with mutex_destroy() in nvme_tcp_free_queue(), and causes the WARN below. DEBUG_LOCKS_WARN_ON(lock->magic != lock) WARNING: CPU: 3 PID: 34077 at kernel/locking/mutex.c:587 __mutex_lock+0xcf0/0x1220 Modules linked in: nvmet_tcp nvmet nvme_tcp nvme_fabrics iw_cm ib_cm ib_core pktcdvd nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip_set nf_tables qrtr sunrpc ppdev 9pnet_virtio 9pnet pcspkr netfs parport_pc parport e1000 i2c_piix4 i2c_smbus loop fuse nfnetlink zram bochs drm_vram_helper drm_ttm_helper ttm drm_kms_helper xfs drm sym53c8xx floppy nvme scsi_transport_spi nvme_core nvme_auth serio_raw ata_generic pata_acpi dm_multipath qemu_fw_cfg [last unloaded: ib_uverbs] CPU: 3 UID: 0 PID: 34077 Comm: udisksd Not tainted 6.11.0-rc7 #319 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014 RIP: 0010:__mutex_lock+0xcf0/0x1220 Code: 08 84 d2 0f 85 c8 04 00 00 8b 15 ef b6 c8 01 85 d2 0f 85 78 f4 ff ff 48 c7 c6 20 93 ee af 48 c7 c7 60 91 ee af e8 f0 a7 6d fd <0f> 0b e9 5e f4 ff ff 48 b8 00 00 00 00 00 fc ff df 4c 89 f2 48 c1 RSP: 0018:ffff88811305f760 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff88812c652058 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000001 RBP: ffff88811305f8b0 R08: 0000000000000001 R09: ffffed1075c36341 R10: ffff8883ae1b1a0b R11: 0000000000010498 R12: 0000000000000000 R13: 0000000000000000 R14: dffffc0000000000 R15: ffff88812c652058 FS: 00007f9713ae4980(0000) GS:ffff8883ae180000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fcd78483c7c CR3: 0000000122c38000 CR4: 00000000000006f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? __warn.cold+0x5b/0x1af ? __mutex_lock+0xcf0/0x1220 ? report_bug+0x1ec/0x390 ? handle_bug+0x3c/0x80 ? exc_invalid_op+0x13/0x40 ? asm_exc_invalid_op+0x16/0x20 ? __mutex_lock+0xcf0/0x1220 ? nvme_tcp_get_address+0xc2/0x1e0 [nvme_tcp] ? __pfx___mutex_lock+0x10/0x10 ? __lock_acquire+0xd6a/0x59e0 ? nvme_tcp_get_address+0xc2/0x1e0 [nvme_tcp] nvme_tcp_get_address+0xc2/0x1e0 [nvme_tcp] ? __pfx_nvme_tcp_get_address+0x10/0x10 [nvme_tcp] nvme_sysfs_show_address+0x81/0xc0 [nvme_core] dev_attr_show+0x42/0x80 ? __asan_memset+0x1f/0x40 sysfs_kf_seq_show+0x1f0/0x370 seq_read_iter+0x2cb/0x1130 ? rw_verify_area+0x3b1/0x590 ? __mutex_lock+0x433/0x1220 vfs_read+0x6a6/0xa20 ? lockdep_hardirqs_on+0x78/0x100 ? __pfx_vfs_read+0x10/0x10 ksys_read+0xf7/0x1d0 ? __pfx_ksys_read+0x10/0x10 ? __x64_sys_openat+0x105/0x1d0 do_syscall_64+0x93/0x180 ? lockdep_hardirqs_on_prepare+0x16d/0x400 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on+0x78/0x100 ? do_syscall_64+0x9f/0x180 ? __pfx_ksys_read+0x10/0x10 ? lockdep_hardirqs_on_prepare+0x16d/0x400 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on+0x78/0x100 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on_prepare+0x16d/0x400 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on+0x78/0x100 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on_prepare+0x16d/0x400 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on+0x78/0x100 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on_prepare+0x16d/0x400 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on+0x78/0x100 ? do_syscall_64+0x9f/0x180 ? do_syscall_64+0x9f/0x180 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7f9713f55cfa Code: 55 48 89 e5 48 83 ec 20 48 89 55 e8 48 89 75 f0 89 7d f8 e8 e8 74 f8 ff 48 8b 55 e8 48 8b 75 f0 4 ---truncated---

A race problem was found in fs/proc/task_mmu.c in the memory management sub-component in the Linux kernel. This issue may allow a local attacker with user privilege to cause a denial of service.

In the Linux kernel, the following vulnerability has been resolved: rcu/kvfree: Fix data-race in __mod_timer / kvfree_call_rcu KCSAN reports a data race when access the krcp->monitor_work.timer.expires variable in the schedule_delayed_monitor_work() function: <snip> BUG: KCSAN: data-race in __mod_timer / kvfree_call_rcu read to 0xffff888237d1cce8 of 8 bytes by task 10149 on cpu 1: schedule_delayed_monitor_work kernel/rcu/tree.c:3520 [inline] kvfree_call_rcu+0x3b8/0x510 kernel/rcu/tree.c:3839 trie_update_elem+0x47c/0x620 kernel/bpf/lpm_trie.c:441 bpf_map_update_value+0x324/0x350 kernel/bpf/syscall.c:203 generic_map_update_batch+0x401/0x520 kernel/bpf/syscall.c:1849 bpf_map_do_batch+0x28c/0x3f0 kernel/bpf/syscall.c:5143 __sys_bpf+0x2e5/0x7a0 __do_sys_bpf kernel/bpf/syscall.c:5741 [inline] __se_sys_bpf kernel/bpf/syscall.c:5739 [inline] __x64_sys_bpf+0x43/0x50 kernel/bpf/syscall.c:5739 x64_sys_call+0x2625/0x2d60 arch/x86/include/generated/asm/syscalls_64.h:322 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xc9/0x1c0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f write to 0xffff888237d1cce8 of 8 bytes by task 56 on cpu 0: __mod_timer+0x578/0x7f0 kernel/time/timer.c:1173 add_timer_global+0x51/0x70 kernel/time/timer.c:1330 __queue_delayed_work+0x127/0x1a0 kernel/workqueue.c:2523 queue_delayed_work_on+0xdf/0x190 kernel/workqueue.c:2552 queue_delayed_work include/linux/workqueue.h:677 [inline] schedule_delayed_monitor_work kernel/rcu/tree.c:3525 [inline] kfree_rcu_monitor+0x5e8/0x660 kernel/rcu/tree.c:3643 process_one_work kernel/workqueue.c:3229 [inline] process_scheduled_works+0x483/0x9a0 kernel/workqueue.c:3310 worker_thread+0x51d/0x6f0 kernel/workqueue.c:3391 kthread+0x1d1/0x210 kernel/kthread.c:389 ret_from_fork+0x4b/0x60 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 Reported by Kernel Concurrency Sanitizer on: CPU: 0 UID: 0 PID: 56 Comm: kworker/u8:4 Not tainted 6.12.0-rc2-syzkaller-00050-g5b7c893ed5ed #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 Workqueue: events_unbound kfree_rcu_monitor <snip> kfree_rcu_monitor() rearms the work if a "krcp" has to be still offloaded and this is done without holding krcp->lock, whereas the kvfree_call_rcu() holds it. Fix it by acquiring the "krcp->lock" for kfree_rcu_monitor() so both functions do not race anymore.

In the Linux kernel, the following vulnerability has been resolved: fscache: Fix oops due to race with cookie_lru and use_cookie If a cookie expires from the LRU and the LRU_DISCARD flag is set, but the state machine has not run yet, it's possible another thread can call fscache_use_cookie and begin to use it. When the cookie_worker finally runs, it will see the LRU_DISCARD flag set, transition the cookie->state to LRU_DISCARDING, which will then withdraw the cookie. Once the cookie is withdrawn the object is removed the below oops will occur because the object associated with the cookie is now NULL. Fix the oops by clearing the LRU_DISCARD bit if another thread uses the cookie before the cookie_worker runs. BUG: kernel NULL pointer dereference, address: 0000000000000008 ... CPU: 31 PID: 44773 Comm: kworker/u130:1 Tainted: G E 6.0.0-5.dneg.x86_64 #1 Hardware name: Google Compute Engine/Google Compute Engine, BIOS Google 08/26/2022 Workqueue: events_unbound netfs_rreq_write_to_cache_work [netfs] RIP: 0010:cachefiles_prepare_write+0x28/0x90 [cachefiles] ... Call Trace: netfs_rreq_write_to_cache_work+0x11c/0x320 [netfs] process_one_work+0x217/0x3e0 worker_thread+0x4a/0x3b0 kthread+0xd6/0x100

In the Linux kernel, the following vulnerability has been resolved: ath11k: fix netdev open race Make sure to allocate resources needed before registering the device. This specifically avoids having a racing open() trigger a BUG_ON() in mod_timer() when ath11k_mac_op_start() is called before the mon_reap_timer as been set up. I did not see this issue with next-20220310, but I hit it on every probe with next-20220511. Perhaps some timing changed in between. Here's the backtrace: [ 51.346947] kernel BUG at kernel/time/timer.c:990! [ 51.346958] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ... [ 51.578225] Call trace: [ 51.583293] __mod_timer+0x298/0x390 [ 51.589518] mod_timer+0x14/0x20 [ 51.595368] ath11k_mac_op_start+0x41c/0x4a0 [ath11k] [ 51.603165] drv_start+0x38/0x60 [mac80211] [ 51.610110] ieee80211_do_open+0x29c/0x7d0 [mac80211] [ 51.617945] ieee80211_open+0x60/0xb0 [mac80211] [ 51.625311] __dev_open+0x100/0x1c0 [ 51.631420] __dev_change_flags+0x194/0x210 [ 51.638214] dev_change_flags+0x24/0x70 [ 51.644646] do_setlink+0x228/0xdb0 [ 51.650723] __rtnl_newlink+0x460/0x830 [ 51.657162] rtnl_newlink+0x4c/0x80 [ 51.663229] rtnetlink_rcv_msg+0x124/0x390 [ 51.669917] netlink_rcv_skb+0x58/0x130 [ 51.676314] rtnetlink_rcv+0x18/0x30 [ 51.682460] netlink_unicast+0x250/0x310 [ 51.688960] netlink_sendmsg+0x19c/0x3e0 [ 51.695458] ____sys_sendmsg+0x220/0x290 [ 51.701938] ___sys_sendmsg+0x7c/0xc0 [ 51.708148] __sys_sendmsg+0x68/0xd0 [ 51.714254] __arm64_sys_sendmsg+0x28/0x40 [ 51.720900] invoke_syscall+0x48/0x120 Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3

In the Linux kernel, the following vulnerability has been resolved: scsi: target: iscsi: Fix a race condition between login_work and the login thread In case a malicious initiator sends some random data immediately after a login PDU; the iscsi_target_sk_data_ready() callback will schedule the login_work and, at the same time, the negotiation may end without clearing the LOGIN_FLAGS_INITIAL_PDU flag (because no additional PDU exchanges are required to complete the login). The login has been completed but the login_work function will find the LOGIN_FLAGS_INITIAL_PDU flag set and will never stop from rescheduling itself; at this point, if the initiator drops the connection, the iscsit_conn structure will be freed, login_work will dereference a released socket structure and the kernel crashes. BUG: kernel NULL pointer dereference, address: 0000000000000230 PF: supervisor write access in kernel mode PF: error_code(0x0002) - not-present page Workqueue: events iscsi_target_do_login_rx [iscsi_target_mod] RIP: 0010:_raw_read_lock_bh+0x15/0x30 Call trace: iscsi_target_do_login_rx+0x75/0x3f0 [iscsi_target_mod] process_one_work+0x1e8/0x3c0 Fix this bug by forcing login_work to stop after the login has been completed and the socket callbacks have been restored. Add a comment to clearify the return values of iscsi_target_do_login()

In the Linux kernel, the following vulnerability has been resolved: net: xilinx: axienet: Enqueue Tx packets in dql before dmaengine starts Enqueue packets in dql after dma engine starts causes race condition. Tx transfer starts once dma engine is started and may execute dql dequeue in completion before it gets queued. It results in following kernel crash while running iperf stress test: kernel BUG at lib/dynamic_queue_limits.c:99! <snip> Internal error: Oops - BUG: 00000000f2000800 [#1] SMP pc : dql_completed+0x238/0x248 lr : dql_completed+0x3c/0x248 Call trace: dql_completed+0x238/0x248 axienet_dma_tx_cb+0xa0/0x170 xilinx_dma_do_tasklet+0xdc/0x290 tasklet_action_common+0xf8/0x11c tasklet_action+0x30/0x3c handle_softirqs+0xf8/0x230 <snip> Start dmaengine after enqueue in dql fixes the crash.

In the Linux kernel, the following vulnerability has been resolved: net: qrtr: start MHI channel after endpoit creation MHI channel may generates event/interrupt right after enabling. It may leads to 2 race conditions issues. 1) Such event may be dropped by qcom_mhi_qrtr_dl_callback() at check: if (!qdev || mhi_res->transaction_status) return; Because dev_set_drvdata(&mhi_dev->dev, qdev) may be not performed at this moment. In this situation qrtr-ns will be unable to enumerate services in device. --------------------------------------------------------------- 2) Such event may come at the moment after dev_set_drvdata() and before qrtr_endpoint_register(). In this case kernel will panic with accessing wrong pointer at qcom_mhi_qrtr_dl_callback(): rc = qrtr_endpoint_post(&qdev->ep, mhi_res->buf_addr, mhi_res->bytes_xferd); Because endpoint is not created yet. -------------------------------------------------------------- So move mhi_prepare_for_transfer_autoqueue after endpoint creation to fix it.

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix race between quota enable and quota rescan ioctl When enabling quotas, at btrfs_quota_enable(), after committing the transaction, we change fs_info->quota_root to point to the quota root we created and set BTRFS_FS_QUOTA_ENABLED at fs_info->flags. Then we try to start the qgroup rescan worker, first by initializing it with a call to qgroup_rescan_init() - however if that fails we end up freeing the quota root but we leave fs_info->quota_root still pointing to it, this can later result in a use-after-free somewhere else. We have previously set the flags BTRFS_FS_QUOTA_ENABLED and BTRFS_QGROUP_STATUS_FLAG_ON, so we can only fail with -EINPROGRESS at btrfs_quota_enable(), which is possible if someone already called the quota rescan ioctl, and therefore started the rescan worker. So fix this by ignoring an -EINPROGRESS and asserting we can't get any other error.

In the Linux kernel, the following vulnerability has been resolved: drm/panthor: Fix race when converting group handle to group object XArray provides it's own internal lock which protects the internal array when entries are being simultaneously added and removed. However there is still a race between retrieving the pointer from the XArray and incrementing the reference count. To avoid this race simply hold the internal XArray lock when incrementing the reference count, this ensures there cannot be a racing call to xa_erase().

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Ensure DA_ID handling completion before deleting an NPIV instance Deleting an NPIV instance requires all fabric ndlps to be released before an NPIV's resources can be torn down. Failure to release fabric ndlps beforehand opens kref imbalance race conditions. Fix by forcing the DA_ID to complete synchronously with usage of wait_queue.

In the Linux kernel, the following vulnerability has been resolved: fs: dlm: fix race in lowcomms This patch fixes a race between queue_work() in _dlm_lowcomms_commit_msg() and srcu_read_unlock(). The queue_work() can take the final reference of a dlm_msg and so msg->idx can contain garbage which is signaled by the following warning: [ 676.237050] ------------[ cut here ]------------ [ 676.237052] WARNING: CPU: 0 PID: 1060 at include/linux/srcu.h:189 dlm_lowcomms_commit_msg+0x41/0x50 [ 676.238945] Modules linked in: dlm_locktorture torture rpcsec_gss_krb5 intel_rapl_msr intel_rapl_common iTCO_wdt iTCO_vendor_support qxl kvm_intel drm_ttm_helper vmw_vsock_virtio_transport kvm vmw_vsock_virtio_transport_common ttm irqbypass crc32_pclmul joydev crc32c_intel serio_raw drm_kms_helper vsock virtio_scsi virtio_console virtio_balloon snd_pcm drm syscopyarea sysfillrect sysimgblt snd_timer fb_sys_fops i2c_i801 lpc_ich snd i2c_smbus soundcore pcspkr [ 676.244227] CPU: 0 PID: 1060 Comm: lock_torture_wr Not tainted 5.19.0-rc3+ #1546 [ 676.245216] Hardware name: Red Hat KVM/RHEL-AV, BIOS 1.16.0-2.module+el8.7.0+15506+033991b0 04/01/2014 [ 676.246460] RIP: 0010:dlm_lowcomms_commit_msg+0x41/0x50 [ 676.247132] Code: fe ff ff ff 75 24 48 c7 c6 bd 0f 49 bb 48 c7 c7 38 7c 01 bd e8 00 e7 ca ff 89 de 48 c7 c7 60 78 01 bd e8 42 3d cd ff 5b 5d c3 <0f> 0b eb d8 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 55 48 [ 676.249253] RSP: 0018:ffffa401c18ffc68 EFLAGS: 00010282 [ 676.249855] RAX: 0000000000000001 RBX: 00000000ffff8b76 RCX: 0000000000000006 [ 676.250713] RDX: 0000000000000000 RSI: ffffffffbccf3a10 RDI: ffffffffbcc7b62e [ 676.251610] RBP: ffffa401c18ffc70 R08: 0000000000000001 R09: 0000000000000001 [ 676.252481] R10: 0000000000000001 R11: 0000000000000001 R12: 0000000000000005 [ 676.253421] R13: ffff8b76786ec370 R14: ffff8b76786ec370 R15: ffff8b76786ec480 [ 676.254257] FS: 0000000000000000(0000) GS:ffff8b7777800000(0000) knlGS:0000000000000000 [ 676.255239] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 676.255897] CR2: 00005590205d88b8 CR3: 000000017656c003 CR4: 0000000000770ee0 [ 676.256734] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 676.257567] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 676.258397] PKRU: 55555554 [ 676.258729] Call Trace: [ 676.259063] <TASK> [ 676.259354] dlm_midcomms_commit_mhandle+0xcc/0x110 [ 676.259964] queue_bast+0x8b/0xb0 [ 676.260423] grant_pending_locks+0x166/0x1b0 [ 676.261007] _unlock_lock+0x75/0x90 [ 676.261469] unlock_lock.isra.57+0x62/0xa0 [ 676.262009] dlm_unlock+0x21e/0x330 [ 676.262457] ? lock_torture_stats+0x80/0x80 [dlm_locktorture] [ 676.263183] torture_unlock+0x5a/0x90 [dlm_locktorture] [ 676.263815] ? preempt_count_sub+0xba/0x100 [ 676.264361] ? complete+0x1d/0x60 [ 676.264777] lock_torture_writer+0xb8/0x150 [dlm_locktorture] [ 676.265555] kthread+0x10a/0x130 [ 676.266007] ? kthread_complete_and_exit+0x20/0x20 [ 676.266616] ret_from_fork+0x22/0x30 [ 676.267097] </TASK> [ 676.267381] irq event stamp: 9579855 [ 676.267824] hardirqs last enabled at (9579863): [<ffffffffbb14e6f8>] __up_console_sem+0x58/0x60 [ 676.268896] hardirqs last disabled at (9579872): [<ffffffffbb14e6dd>] __up_console_sem+0x3d/0x60 [ 676.270008] softirqs last enabled at (9579798): [<ffffffffbc200349>] __do_softirq+0x349/0x4c7 [ 676.271438] softirqs last disabled at (9579897): [<ffffffffbb0d54c0>] irq_exit_rcu+0xb0/0xf0 [ 676.272796] ---[ end trace 0000000000000000 ]--- I reproduced this warning with dlm_locktorture test which is currently not upstream. However this patch fix the issue by make a additional refcount between dlm_lowcomms_new_msg() and dlm_lowcomms_commit_msg(). In case of the race the kref_put() in dlm_lowcomms_commit_msg() will be the final put.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix data-races around sysctl_tcp_max_reordering. While reading sysctl_tcp_max_reordering, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix a data-race around sysctl_tcp_early_retrans. While reading sysctl_tcp_early_retrans, it can be changed concurrently. Thus, we need to add READ_ONCE() to its reader.

In the Linux kernel, the following vulnerability has been resolved: dm ioctl: fix misbehavior if list_versions races with module loading __list_versions will first estimate the required space using the "dm_target_iterate(list_version_get_needed, &needed)" call and then will fill the space using the "dm_target_iterate(list_version_get_info, &iter_info)" call. Each of these calls locks the targets using the "down_read(&_lock)" and "up_read(&_lock)" calls, however between the first and second "dm_target_iterate" there is no lock held and the target modules can be loaded at this point, so the second "dm_target_iterate" call may need more space than what was the first "dm_target_iterate" returned. The code tries to handle this overflow (see the beginning of list_version_get_info), however this handling is incorrect. The code sets "param->data_size = param->data_start + needed" and "iter_info.end = (char *)vers+len" - "needed" is the size returned by the first dm_target_iterate call; "len" is the size of the buffer allocated by userspace. "len" may be greater than "needed"; in this case, the code will write up to "len" bytes into the buffer, however param->data_size is set to "needed", so it may write data past the param->data_size value. The ioctl interface copies only up to param->data_size into userspace, thus part of the result will be truncated. Fix this bug by setting "iter_info.end = (char *)vers + needed;" - this guarantees that the second "dm_target_iterate" call will write only up to the "needed" buffer and it will exit with "DM_BUFFER_FULL_FLAG" if it overflows the "needed" space - in this case, userspace will allocate a larger buffer and retry. Note that there is also a bug in list_version_get_needed - we need to add "strlen(tt->name) + 1" to the needed size, not "strlen(tt->name)".

In the Linux kernel, the following vulnerability has been resolved: sysctl: Fix data races in proc_douintvec(). A sysctl variable is accessed concurrently, and there is always a chance of data-race. So, all readers and writers need some basic protection to avoid load/store-tearing. This patch changes proc_douintvec() to use READ_ONCE() and WRITE_ONCE() internally to fix data-races on the sysctl side. For now, proc_douintvec() itself is tolerant to a data-race, but we still need to add annotations on the other subsystem's side.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix data-races around sysctl_tcp_recovery. While reading sysctl_tcp_recovery, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: rcu-tasks: Fix race in schedule and flush work While booting secondary CPUs, cpus_read_[lock/unlock] is not keeping online cpumask stable. The transient online mask results in below calltrace. [ 0.324121] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] [ 0.346652] Detected PIPT I-cache on CPU2 [ 0.347212] CPU2: Booted secondary processor 0x0000000002 [0x410fd083] [ 0.377255] Detected PIPT I-cache on CPU3 [ 0.377823] CPU3: Booted secondary processor 0x0000000003 [0x410fd083] [ 0.379040] ------------[ cut here ]------------ [ 0.383662] WARNING: CPU: 0 PID: 10 at kernel/workqueue.c:3084 __flush_work+0x12c/0x138 [ 0.384850] Modules linked in: [ 0.385403] CPU: 0 PID: 10 Comm: rcu_tasks_rude_ Not tainted 5.17.0-rc3-v8+ #13 [ 0.386473] Hardware name: Raspberry Pi 4 Model B Rev 1.4 (DT) [ 0.387289] pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 0.388308] pc : __flush_work+0x12c/0x138 [ 0.388970] lr : __flush_work+0x80/0x138 [ 0.389620] sp : ffffffc00aaf3c60 [ 0.390139] x29: ffffffc00aaf3d20 x28: ffffffc009c16af0 x27: ffffff80f761df48 [ 0.391316] x26: 0000000000000004 x25: 0000000000000003 x24: 0000000000000100 [ 0.392493] x23: ffffffffffffffff x22: ffffffc009c16b10 x21: ffffffc009c16b28 [ 0.393668] x20: ffffffc009e53861 x19: ffffff80f77fbf40 x18: 00000000d744fcc9 [ 0.394842] x17: 000000000000000b x16: 00000000000001c2 x15: ffffffc009e57550 [ 0.396016] x14: 0000000000000000 x13: ffffffffffffffff x12: 0000000100000000 [ 0.397190] x11: 0000000000000462 x10: ffffff8040258008 x9 : 0000000100000000 [ 0.398364] x8 : 0000000000000000 x7 : ffffffc0093c8bf4 x6 : 0000000000000000 [ 0.399538] x5 : 0000000000000000 x4 : ffffffc00a976e40 x3 : ffffffc00810444c [ 0.400711] x2 : 0000000000000004 x1 : 0000000000000000 x0 : 0000000000000000 [ 0.401886] Call trace: [ 0.402309] __flush_work+0x12c/0x138 [ 0.402941] schedule_on_each_cpu+0x228/0x278 [ 0.403693] rcu_tasks_rude_wait_gp+0x130/0x144 [ 0.404502] rcu_tasks_kthread+0x220/0x254 [ 0.405264] kthread+0x174/0x1ac [ 0.405837] ret_from_fork+0x10/0x20 [ 0.406456] irq event stamp: 102 [ 0.406966] hardirqs last enabled at (101): [<ffffffc0093c8468>] _raw_spin_unlock_irq+0x78/0xb4 [ 0.408304] hardirqs last disabled at (102): [<ffffffc0093b8270>] el1_dbg+0x24/0x5c [ 0.409410] softirqs last enabled at (54): [<ffffffc0081b80c8>] local_bh_enable+0xc/0x2c [ 0.410645] softirqs last disabled at (50): [<ffffffc0081b809c>] local_bh_disable+0xc/0x2c [ 0.411890] ---[ end trace 0000000000000000 ]--- [ 0.413000] smp: Brought up 1 node, 4 CPUs [ 0.413762] SMP: Total of 4 processors activated. [ 0.414566] CPU features: detected: 32-bit EL0 Support [ 0.415414] CPU features: detected: 32-bit EL1 Support [ 0.416278] CPU features: detected: CRC32 instructions [ 0.447021] Callback from call_rcu_tasks_rude() invoked. [ 0.506693] Callback from call_rcu_tasks() invoked. This commit therefore fixes this issue by applying a single-CPU optimization to the RCU Tasks Rude grace-period process. The key point here is that the purpose of this RCU flavor is to force a schedule on each online CPU since some past event. But the rcu_tasks_rude_wait_gp() function runs in the context of the RCU Tasks Rude's grace-period kthread, so there must already have been a context switch on the current CPU since the call to either synchronize_rcu_tasks_rude() or call_rcu_tasks_rude(). So if there is only a single CPU online, RCU Tasks Rude's grace-period kthread does not need to anything at all. It turns out that the rcu_tasks_rude_wait_gp() function's call to schedule_on_each_cpu() causes problems during early boot. During that time, there is only one online CPU, namely the boot CPU. Therefore, applying this single-CPU optimization fixes early-boot instances of this problem.

In the Linux kernel, the following vulnerability has been resolved: nvme-pci: fix race condition between reset and nvme_dev_disable() nvme_dev_disable() modifies the dev->online_queues field, therefore nvme_pci_update_nr_queues() should avoid racing against it, otherwise we could end up passing invalid values to blk_mq_update_nr_hw_queues(). WARNING: CPU: 39 PID: 61303 at drivers/pci/msi/api.c:347 pci_irq_get_affinity+0x187/0x210 Workqueue: nvme-reset-wq nvme_reset_work [nvme] RIP: 0010:pci_irq_get_affinity+0x187/0x210 Call Trace: <TASK> ? blk_mq_pci_map_queues+0x87/0x3c0 ? pci_irq_get_affinity+0x187/0x210 blk_mq_pci_map_queues+0x87/0x3c0 nvme_pci_map_queues+0x189/0x460 [nvme] blk_mq_update_nr_hw_queues+0x2a/0x40 nvme_reset_work+0x1be/0x2a0 [nvme] Fix the bug by locking the shutdown_lock mutex before using dev->online_queues. Give up if nvme_dev_disable() is running or if it has been executed already.

In the Linux kernel, the following vulnerability has been resolved: ip: Fix data-races around sysctl_ip_fwd_use_pmtu. While reading sysctl_ip_fwd_use_pmtu, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: kcm: close race conditions on sk_receive_queue sk->sk_receive_queue is protected by skb queue lock, but for KCM sockets its RX path takes mux->rx_lock to protect more than just skb queue. However, kcm_recvmsg() still only grabs the skb queue lock, so race conditions still exist. We can teach kcm_recvmsg() to grab mux->rx_lock too but this would introduce a potential performance regression as struct kcm_mux can be shared by multiple KCM sockets. So we have to enforce skb queue lock in requeue_rx_msgs() and handle skb peek case carefully in kcm_wait_data(). Fortunately, skb_recv_datagram() already handles it nicely and is widely used by other sockets, we can just switch to skb_recv_datagram() after getting rid of the unnecessary sock lock in kcm_recvmsg() and kcm_splice_read(). Side note: SOCK_DONE is not used by KCM sockets, so it is safe to get rid of this check too. I ran the original syzbot reproducer for 30 min without seeing any issue.

In the Linux kernel, the following vulnerability has been resolved: tracing: Fix race where eprobes can be called before the event The flag that tells the event to call its triggers after reading the event is set for eprobes after the eprobe is enabled. This leads to a race where the eprobe may be triggered at the beginning of the event where the record information is NULL. The eprobe then dereferences the NULL record causing a NULL kernel pointer bug. Test for a NULL record to keep this from happening.

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix a data-race around bpf_jit_limit. While reading bpf_jit_limit, it can be changed concurrently via sysctl, WRITE_ONCE() in __do_proc_doulongvec_minmax(). The size of bpf_jit_limit is long, so we need to add a paired READ_ONCE() to avoid load-tearing.