In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix bug on trap in smb2_lock If lock count is greater than 1, flags could be old value. It should be checked with flags of smb_lock, not flags. It will cause bug-on trap from locks_free_lock in error handling routine.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix WARNING "do not call blocking ops when !TASK_RUNNING" wait_event_timeout() will set the state of the current task to TASK_UNINTERRUPTIBLE, before doing the condition check. This means that ksmbd_durable_scavenger_alive() will try to acquire the mutex while already in a sleeping state. The scheduler warns us by giving the following warning: do not call blocking ops when !TASK_RUNNING; state=2 set at [<0000000061515a6f>] prepare_to_wait_event+0x9f/0x6c0 WARNING: CPU: 2 PID: 4147 at kernel/sched/core.c:10099 __might_sleep+0x12f/0x160 mutex lock is not needed in ksmbd_durable_scavenger_alive().

In the Linux kernel, the following vulnerability has been resolved: usb: cdns3: Fix deadlock when using NCM gadget The cdns3 driver has the same NCM deadlock as fixed in cdnsp by commit 58f2fcb3a845 ("usb: cdnsp: Fix deadlock issue during using NCM gadget"). Under PREEMPT_RT the deadlock can be readily triggered by heavy network traffic, for example using "iperf --bidir" over NCM ethernet link. The deadlock occurs because the threaded interrupt handler gets preempted by a softirq, but both are protected by the same spinlock. Prevent deadlock by disabling softirq during threaded irq handler.

In the Linux kernel, the following vulnerability has been resolved: net: cadence: macb: Fix a possible deadlock in macb_halt_tx. There is a situation where after THALT is set high, TGO stays high as well. Because jiffies are never updated, as we are in a context with interrupts disabled, we never exit that loop and have a deadlock. That deadlock was noticed on a sama5d4 device that stayed locked for days. Use retries instead of jiffies so that the timeout really works and we do not have a deadlock anymore.

In the Linux kernel, the following vulnerability has been resolved: iio: imu: st_lsm6dsx: fix possible lockup in st_lsm6dsx_read_fifo Prevent st_lsm6dsx_read_fifo from falling in an infinite loop in case pattern_len is equal to zero and the device FIFO is not empty.

In the Linux kernel, the following vulnerability has been resolved: um: work around sched_yield not yielding in time-travel mode sched_yield by a userspace may not actually cause scheduling in time-travel mode as no time has passed. In the case seen it appears to be a badly implemented userspace spinlock in ASAN. Unfortunately, with time-travel it causes an extreme slowdown or even deadlock depending on the kernel configuration (CONFIG_UML_MAX_USERSPACE_ITERATIONS). Work around it by accounting time to the process whenever it executes a sched_yield syscall.

In the Linux kernel, the following vulnerability has been resolved: ftrace: Add cond_resched() to ftrace_graph_set_hash() When the kernel contains a large number of functions that can be traced, the loop in ftrace_graph_set_hash() may take a lot of time to execute. This may trigger the softlockup watchdog. Add cond_resched() within the loop to allow the kernel to remain responsive even when processing a large number of functions. This matches the cond_resched() that is used in other locations of the code that iterates over all functions that can be traced.

In the Linux kernel, the following vulnerability has been resolved: e1000: Move cancel_work_sync to avoid deadlock Previously, e1000_down called cancel_work_sync for the e1000 reset task (via e1000_down_and_stop), which takes RTNL. As reported by users and syzbot, a deadlock is possible in the following scenario: CPU 0: - RTNL is held - e1000_close - e1000_down - cancel_work_sync (cancel / wait for e1000_reset_task()) CPU 1: - process_one_work - e1000_reset_task - take RTNL To remedy this, avoid calling cancel_work_sync from e1000_down (e1000_reset_task does nothing if the device is down anyway). Instead, call cancel_work_sync for e1000_reset_task when the device is being removed.

In the Linux kernel, the following vulnerability has been resolved: md: fix array_state=clear sysfs deadlock When "clear" is written to array_state, md_attr_store() breaks sysfs active protection so the array can delete itself from its own sysfs store method. However, md_attr_store() currently drops the mddev reference before calling sysfs_unbreak_active_protection(). Once do_md_stop(..., 0) has made the mddev eligible for delayed deletion, the temporary kobject reference taken by sysfs_break_active_protection() can become the last kobject reference protecting the md kobject. That allows sysfs_unbreak_active_protection() to drop the last kobject reference from the current sysfs writer context. kobject teardown then recurses into kernfs removal while the current sysfs node is still being unwound, and lockdep reports recursive locking on kn->active with kernfs_drain() in the call chain. Reproducer on an existing level: 1. Create an md0 linear array and activate it: mknod /dev/md0 b 9 0 echo none > /sys/block/md0/md/metadata_version echo linear > /sys/block/md0/md/level echo 1 > /sys/block/md0/md/raid_disks echo "$(cat /sys/class/block/sdb/dev)" > /sys/block/md0/md/new_dev echo "$(($(cat /sys/class/block/sdb/size) / 2))" > \ /sys/block/md0/md/dev-sdb/size echo 0 > /sys/block/md0/md/dev-sdb/slot echo active > /sys/block/md0/md/array_state 2. Wait briefly for the array to settle, then clear it: sleep 2 echo clear > /sys/block/md0/md/array_state The warning looks like: WARNING: possible recursive locking detected bash/588 is trying to acquire lock: (kn->active#65) at __kernfs_remove+0x157/0x1d0 but task is already holding lock: (kn->active#65) at sysfs_unbreak_active_protection+0x1f/0x40 ... Call Trace: kernfs_drain __kernfs_remove kernfs_remove_by_name_ns sysfs_remove_group sysfs_remove_groups __kobject_del kobject_put md_attr_store kernfs_fop_write_iter vfs_write ksys_write Restore active protection before mddev_put() so the extra sysfs kobject reference is dropped while the mddev is still held alive. The actual md kobject deletion is then deferred until after the sysfs write path has fully returned.

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix deadlock between reflink and transaction commit when using flushoncommit When using the flushoncommit mount option, we can have a deadlock between a transaction commit and a reflink operation that copied an inline extent to an offset beyond the current i_size of the destination node. The deadlock happens like this: 1) Task A clones an inline extent from inode X to an offset of inode Y that is beyond Y's current i_size. This means we copied the inline extent's data to a folio of inode Y that is beyond its EOF, using a call to copy_inline_to_page(); 2) Task B starts a transaction commit and calls btrfs_start_delalloc_flush() to flush delalloc; 3) The delalloc flushing sees the new dirty folio of inode Y and when it attempts to flush it, it ends up at extent_writepage() and sees that the offset of the folio is beyond the i_size of inode Y, so it attempts to invalidate the folio by calling folio_invalidate(), which ends up at btrfs' folio invalidate callback - btrfs_invalidate_folio(). There it tries to lock the folio's range in inode Y's extent io tree, but it blocks since it's currently locked by task A - during a reflink we lock the inodes and the source and destination ranges after flushing all delalloc and waiting for ordered extent completion - after that we don't expect to have dirty folios in the ranges, the exception is if we have to copy an inline extent's data (because the destination offset is not zero); 4) Task A then attempts to start a transaction to update the inode item, and then it's blocked since the current transaction is in the TRANS_STATE_COMMIT_START state. Therefore task A has to wait for the current transaction to become unblocked (its state >= TRANS_STATE_UNBLOCKED). So task A is waiting for the transaction commit done by task B, and the later waiting on the extent lock of inode Y that is currently held by task A. Syzbot recently reported this with the following stack traces: INFO: task kworker/u8:7:1053 blocked for more than 143 seconds. Not tainted syzkaller #0 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. task:kworker/u8:7 state:D stack:23520 pid:1053 tgid:1053 ppid:2 task_flags:0x4208060 flags:0x00080000 Workqueue: writeback wb_workfn (flush-btrfs-46) Call Trace: <TASK> context_switch kernel/sched/core.c:5298 [inline] __schedule+0x1553/0x5240 kernel/sched/core.c:6911 __schedule_loop kernel/sched/core.c:6993 [inline] schedule+0x164/0x360 kernel/sched/core.c:7008 wait_extent_bit fs/btrfs/extent-io-tree.c:811 [inline] btrfs_lock_extent_bits+0x59c/0x700 fs/btrfs/extent-io-tree.c:1914 btrfs_lock_extent fs/btrfs/extent-io-tree.h:152 [inline] btrfs_invalidate_folio+0x43d/0xc40 fs/btrfs/inode.c:7704 extent_writepage fs/btrfs/extent_io.c:1852 [inline] extent_write_cache_pages fs/btrfs/extent_io.c:2580 [inline] btrfs_writepages+0x12ff/0x2440 fs/btrfs/extent_io.c:2713 do_writepages+0x32e/0x550 mm/page-writeback.c:2554 __writeback_single_inode+0x133/0x11a0 fs/fs-writeback.c:1750 writeback_sb_inodes+0x995/0x19d0 fs/fs-writeback.c:2042 wb_writeback+0x456/0xb70 fs/fs-writeback.c:2227 wb_do_writeback fs/fs-writeback.c:2374 [inline] wb_workfn+0x41a/0xf60 fs/fs-writeback.c:2414 process_one_work kernel/workqueue.c:3276 [inline] process_scheduled_works+0xb6e/0x18c0 kernel/workqueue.c:3359 worker_thread+0xa53/0xfc0 kernel/workqueue.c:3440 kthread+0x388/0x470 kernel/kthread.c:436 ret_from_fork+0x51e/0xb90 arch/x86/kernel/process.c:158 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245 </TASK> INFO: task syz.4.64:6910 blocked for more than 143 seconds. Not tainted syzkaller #0 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. task:syz.4.64 state:D stack:22752 pid:6910 tgid: ---truncated---

In the Linux kernel, the following vulnerability has been resolved: drivers: staging: rtl8723bs: Fix locking in _rtw_join_timeout_handler() Commit 041879b12ddb ("drivers: staging: rtl8192bs: Fix deadlock in rtw_joinbss_event_prehandle()") besides fixing the deadlock also modified _rtw_join_timeout_handler() to use spin_[un]lock_irq() instead of spin_[un]lock_bh(). _rtw_join_timeout_handler() calls rtw_do_join() which takes pmlmepriv->scanned_queue.lock using spin_[un]lock_bh(). This spin_unlock_bh() call re-enables softirqs which triggers an oops in kernel/softirq.c: __local_bh_enable_ip() when it calls lockdep_assert_irqs_enabled(): [ 244.506087] WARNING: CPU: 2 PID: 0 at kernel/softirq.c:376 __local_bh_enable_ip+0xa6/0x100 ... [ 244.509022] Call Trace: [ 244.509048] <IRQ> [ 244.509100] _rtw_join_timeout_handler+0x134/0x170 [r8723bs] [ 244.509468] ? __pfx__rtw_join_timeout_handler+0x10/0x10 [r8723bs] [ 244.509772] ? __pfx__rtw_join_timeout_handler+0x10/0x10 [r8723bs] [ 244.510076] call_timer_fn+0x95/0x2a0 [ 244.510200] __run_timers.part.0+0x1da/0x2d0 This oops is causd by the switch to spin_[un]lock_irq() which disables the IRQs for the entire duration of _rtw_join_timeout_handler(). Disabling the IRQs is not necessary since all code taking this lock runs from either user contexts or from softirqs, switch back to spin_[un]lock_bh() to fix this.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix deadlock in tc route query code Cited commit causes ABBA deadlock[0] when peer flows are created while holding the devcom rw semaphore. Due to peer flows offload implementation the lock is taken much higher up the call chain and there is no obvious way to easily fix the deadlock. Instead, since tc route query code needs the peer eswitch structure only to perform a lookup in xarray and doesn't perform any sleeping operations with it, refactor the code for lockless execution in following ways: - RCUify the devcom 'data' pointer. When resetting the pointer synchronously wait for RCU grace period before returning. This is fine since devcom is currently only used for synchronization of pairing/unpairing of eswitches which is rare and already expensive as-is. - Wrap all usages of 'paired' boolean in {READ|WRITE}_ONCE(). The flag has already been used in some unlocked contexts without proper annotations (e.g. users of mlx5_devcom_is_paired() function), but it wasn't an issue since all relevant code paths checked it again after obtaining the devcom semaphore. Now it is also used by mlx5_devcom_get_peer_data_rcu() as "best effort" check to return NULL when devcom is being unpaired. Note that while RCU read lock doesn't prevent the unpaired flag from being changed concurrently it still guarantees that reader can continue to use 'data'. - Refactor mlx5e_tc_query_route_vport() function to use new mlx5_devcom_get_peer_data_rcu() API which fixes the deadlock. [0]: [ 164.599612] ====================================================== [ 164.600142] WARNING: possible circular locking dependency detected [ 164.600667] 6.3.0-rc3+ #1 Not tainted [ 164.601021] ------------------------------------------------------ [ 164.601557] handler1/3456 is trying to acquire lock: [ 164.601998] ffff88811f1714b0 (&esw->offloads.encap_tbl_lock){+.+.}-{3:3}, at: mlx5e_attach_encap+0xd8/0x8b0 [mlx5_core] [ 164.603078] but task is already holding lock: [ 164.603617] ffff88810137fc98 (&comp->sem){++++}-{3:3}, at: mlx5_devcom_get_peer_data+0x37/0x80 [mlx5_core] [ 164.604459] which lock already depends on the new lock. [ 164.605190] the existing dependency chain (in reverse order) is: [ 164.605848] -> #1 (&comp->sem){++++}-{3:3}: [ 164.606380] down_read+0x39/0x50 [ 164.606772] mlx5_devcom_get_peer_data+0x37/0x80 [mlx5_core] [ 164.607336] mlx5e_tc_query_route_vport+0x86/0xc0 [mlx5_core] [ 164.607914] mlx5e_tc_tun_route_lookup+0x1a4/0x1d0 [mlx5_core] [ 164.608495] mlx5e_attach_decap_route+0xc6/0x1e0 [mlx5_core] [ 164.609063] mlx5e_tc_add_fdb_flow+0x1ea/0x360 [mlx5_core] [ 164.609627] __mlx5e_add_fdb_flow+0x2d2/0x430 [mlx5_core] [ 164.610175] mlx5e_configure_flower+0x952/0x1a20 [mlx5_core] [ 164.610741] tc_setup_cb_add+0xd4/0x200 [ 164.611146] fl_hw_replace_filter+0x14c/0x1f0 [cls_flower] [ 164.611661] fl_change+0xc95/0x18a0 [cls_flower] [ 164.612116] tc_new_tfilter+0x3fc/0xd20 [ 164.612516] rtnetlink_rcv_msg+0x418/0x5b0 [ 164.612936] netlink_rcv_skb+0x54/0x100 [ 164.613339] netlink_unicast+0x190/0x250 [ 164.613746] netlink_sendmsg+0x245/0x4a0 [ 164.614150] sock_sendmsg+0x38/0x60 [ 164.614522] ____sys_sendmsg+0x1d0/0x1e0 [ 164.614934] ___sys_sendmsg+0x80/0xc0 [ 164.615320] __sys_sendmsg+0x51/0x90 [ 164.615701] do_syscall_64+0x3d/0x90 [ 164.616083] entry_SYSCALL_64_after_hwframe+0x46/0xb0 [ 164.616568] -> #0 (&esw->offloads.encap_tbl_lock){+.+.}-{3:3}: [ 164.617210] __lock_acquire+0x159e/0x26e0 [ 164.617638] lock_acquire+0xc2/0x2a0 [ 164.618018] __mutex_lock+0x92/0xcd0 [ 164.618401] mlx5e_attach_encap+0xd8/0x8b0 [mlx5_core] [ 164.618943] post_process_attr+0x153/0x2d0 [ ---truncated---

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix deadlock when aborting transaction during relocation with scrub Before relocating a block group we pause scrub, then do the relocation and then unpause scrub. The relocation process requires starting and committing a transaction, and if we have a failure in the critical section of the transaction commit path (transaction state >= TRANS_STATE_COMMIT_START), we will deadlock if there is a paused scrub. That results in stack traces like the following: [42.479] BTRFS info (device sdc): relocating block group 53876686848 flags metadata|raid6 [42.936] BTRFS warning (device sdc): Skipping commit of aborted transaction. [42.936] ------------[ cut here ]------------ [42.936] BTRFS: Transaction aborted (error -28) [42.936] WARNING: CPU: 11 PID: 346822 at fs/btrfs/transaction.c:1977 btrfs_commit_transaction+0xcc8/0xeb0 [btrfs] [42.936] Modules linked in: dm_flakey dm_mod loop btrfs (...) [42.936] CPU: 11 PID: 346822 Comm: btrfs Tainted: G W 6.3.0-rc2-btrfs-next-127+ #1 [42.936] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 [42.936] RIP: 0010:btrfs_commit_transaction+0xcc8/0xeb0 [btrfs] [42.936] Code: ff ff 45 8b (...) [42.936] RSP: 0018:ffffb58649633b48 EFLAGS: 00010282 [42.936] RAX: 0000000000000000 RBX: ffff8be6ef4d5bd8 RCX: 0000000000000000 [42.936] RDX: 0000000000000002 RSI: ffffffffb35e7782 RDI: 00000000ffffffff [42.936] RBP: ffff8be6ef4d5c98 R08: 0000000000000000 R09: ffffb586496339e8 [42.936] R10: 0000000000000001 R11: 0000000000000001 R12: ffff8be6d38c7c00 [42.936] R13: 00000000ffffffe4 R14: ffff8be6c268c000 R15: ffff8be6ef4d5cf0 [42.936] FS: 00007f381a82b340(0000) GS:ffff8beddfcc0000(0000) knlGS:0000000000000000 [42.936] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [42.936] CR2: 00007f1e35fb7638 CR3: 0000000117680006 CR4: 0000000000370ee0 [42.936] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [42.936] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [42.936] Call Trace: [42.936] <TASK> [42.936] ? start_transaction+0xcb/0x610 [btrfs] [42.936] prepare_to_relocate+0x111/0x1a0 [btrfs] [42.936] relocate_block_group+0x57/0x5d0 [btrfs] [42.936] ? btrfs_wait_nocow_writers+0x25/0xb0 [btrfs] [42.936] btrfs_relocate_block_group+0x248/0x3c0 [btrfs] [42.936] ? __pfx_autoremove_wake_function+0x10/0x10 [42.936] btrfs_relocate_chunk+0x3b/0x150 [btrfs] [42.936] btrfs_balance+0x8ff/0x11d0 [btrfs] [42.936] ? __kmem_cache_alloc_node+0x14a/0x410 [42.936] btrfs_ioctl+0x2334/0x32c0 [btrfs] [42.937] ? mod_objcg_state+0xd2/0x360 [42.937] ? refill_obj_stock+0xb0/0x160 [42.937] ? seq_release+0x25/0x30 [42.937] ? __rseq_handle_notify_resume+0x3b5/0x4b0 [42.937] ? percpu_counter_add_batch+0x2e/0xa0 [42.937] ? __x64_sys_ioctl+0x88/0xc0 [42.937] __x64_sys_ioctl+0x88/0xc0 [42.937] do_syscall_64+0x38/0x90 [42.937] entry_SYSCALL_64_after_hwframe+0x72/0xdc [42.937] RIP: 0033:0x7f381a6ffe9b [42.937] Code: 00 48 89 44 24 (...) [42.937] RSP: 002b:00007ffd45ecf060 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 [42.937] RAX: ffffffffffffffda RBX: 0000000000000001 RCX: 00007f381a6ffe9b [42.937] RDX: 00007ffd45ecf150 RSI: 00000000c4009420 RDI: 0000000000000003 [42.937] RBP: 0000000000000003 R08: 0000000000000013 R09: 0000000000000000 [42.937] R10: 00007f381a60c878 R11: 0000000000000246 R12: 00007ffd45ed0423 [42.937] R13: 00007ffd45ecf150 R14: 0000000000000000 R15: 00007ffd45ecf148 [42.937] </TASK> [42.937] ---[ end trace 0000000000000000 ]--- [42.937] BTRFS: error (device sdc: state A) in cleanup_transaction:1977: errno=-28 No space left [59.196] INFO: task btrfs:346772 blocked for more than 120 seconds. [59.196] Tainted: G W 6.3.0-rc2-btrfs-next-127+ #1 [59.196] "echo 0 > /proc/sys/kernel/hung_ ---truncated---

In the Linux kernel, the following vulnerability has been resolved: netfilter: ipset: Rework long task execution when adding/deleting entries When adding/deleting large number of elements in one step in ipset, it can take a reasonable amount of time and can result in soft lockup errors. The patch 5f7b51bf09ba ("netfilter: ipset: Limit the maximal range of consecutive elements to add/delete") tried to fix it by limiting the max elements to process at all. However it was not enough, it is still possible that we get hung tasks. Lowering the limit is not reasonable, so the approach in this patch is as follows: rely on the method used at resizing sets and save the state when we reach a smaller internal batch limit, unlock/lock and proceed from the saved state. Thus we can avoid long continuous tasks and at the same time removed the limit to add/delete large number of elements in one step. The nfnl mutex is held during the whole operation which prevents one to issue other ipset commands in parallel.

In the Linux kernel, the following vulnerability has been resolved: mptcp: avoid deadlock on fallback while reinjecting Jakub reported an MPTCP deadlock at fallback time: WARNING: possible recursive locking detected 6.18.0-rc7-virtme #1 Not tainted -------------------------------------------- mptcp_connect/20858 is trying to acquire lock: ff1100001da18b60 (&msk->fallback_lock){+.-.}-{3:3}, at: __mptcp_try_fallback+0xd8/0x280 but task is already holding lock: ff1100001da18b60 (&msk->fallback_lock){+.-.}-{3:3}, at: __mptcp_retrans+0x352/0xaa0 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&msk->fallback_lock); lock(&msk->fallback_lock); *** DEADLOCK *** May be due to missing lock nesting notation 3 locks held by mptcp_connect/20858: #0: ff1100001da18290 (sk_lock-AF_INET){+.+.}-{0:0}, at: mptcp_sendmsg+0x114/0x1bc0 #1: ff1100001db40fd0 (k-sk_lock-AF_INET#2){+.+.}-{0:0}, at: __mptcp_retrans+0x2cb/0xaa0 #2: ff1100001da18b60 (&msk->fallback_lock){+.-.}-{3:3}, at: __mptcp_retrans+0x352/0xaa0 stack backtrace: CPU: 0 UID: 0 PID: 20858 Comm: mptcp_connect Not tainted 6.18.0-rc7-virtme #1 PREEMPT(full) Hardware name: Bochs, BIOS Bochs 01/01/2011 Call Trace: <TASK> dump_stack_lvl+0x6f/0xa0 print_deadlock_bug.cold+0xc0/0xcd validate_chain+0x2ff/0x5f0 __lock_acquire+0x34c/0x740 lock_acquire.part.0+0xbc/0x260 _raw_spin_lock_bh+0x38/0x50 __mptcp_try_fallback+0xd8/0x280 mptcp_sendmsg_frag+0x16c2/0x3050 __mptcp_retrans+0x421/0xaa0 mptcp_release_cb+0x5aa/0xa70 release_sock+0xab/0x1d0 mptcp_sendmsg+0xd5b/0x1bc0 sock_write_iter+0x281/0x4d0 new_sync_write+0x3c5/0x6f0 vfs_write+0x65e/0xbb0 ksys_write+0x17e/0x200 do_syscall_64+0xbb/0xfd0 entry_SYSCALL_64_after_hwframe+0x4b/0x53 RIP: 0033:0x7fa5627cbc5e Code: 4d 89 d8 e8 14 bd 00 00 4c 8b 5d f8 41 8b 93 08 03 00 00 59 5e 48 83 f8 fc 74 11 c9 c3 0f 1f 80 00 00 00 00 48 8b 45 10 0f 05 <c9> c3 83 e2 39 83 fa 08 75 e7 e8 13 ff ff ff 0f 1f 00 f3 0f 1e fa RSP: 002b:00007fff1fe14700 EFLAGS: 00000202 ORIG_RAX: 0000000000000001 RAX: ffffffffffffffda RBX: 0000000000000005 RCX: 00007fa5627cbc5e RDX: 0000000000001f9c RSI: 00007fff1fe16984 RDI: 0000000000000005 RBP: 00007fff1fe14710 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000202 R12: 00007fff1fe16920 R13: 0000000000002000 R14: 0000000000001f9c R15: 0000000000001f9c The packet scheduler could attempt a reinjection after receiving an MP_FAIL and before the infinite map has been transmitted, causing a deadlock since MPTCP needs to do the reinjection atomically from WRT fallback. Address the issue explicitly avoiding the reinjection in the critical scenario. Note that this is the only fallback critical section that could potentially send packets and hit the double-lock.

In the Linux kernel, the following vulnerability has been resolved: KVM: Allow CPU to reschedule while setting per-page memory attributes When running an SEV-SNP guest with a sufficiently large amount of memory (1TB+), the host can experience CPU soft lockups when running an operation in kvm_vm_set_mem_attributes() to set memory attributes on the whole range of guest memory. watchdog: BUG: soft lockup - CPU#8 stuck for 26s! [qemu-kvm:6372] CPU: 8 UID: 0 PID: 6372 Comm: qemu-kvm Kdump: loaded Not tainted 6.15.0-rc7.20250520.el9uek.rc1.x86_64 #1 PREEMPT(voluntary) Hardware name: Oracle Corporation ORACLE SERVER E4-2c/Asm,MB Tray,2U,E4-2c, BIOS 78016600 11/13/2024 RIP: 0010:xas_create+0x78/0x1f0 Code: 00 00 00 41 80 fc 01 0f 84 82 00 00 00 ba 06 00 00 00 bd 06 00 00 00 49 8b 45 08 4d 8d 65 08 41 39 d6 73 20 83 ed 06 48 85 c0 <74> 67 48 89 c2 83 e2 03 48 83 fa 02 75 0c 48 3d 00 10 00 00 0f 87 RSP: 0018:ffffad890a34b940 EFLAGS: 00000286 RAX: ffff96f30b261daa RBX: ffffad890a34b9c8 RCX: 0000000000000000 RDX: 000000000000001e RSI: 0000000000000000 RDI: 0000000000000000 RBP: 0000000000000018 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: ffffad890a356868 R13: ffffad890a356860 R14: 0000000000000000 R15: ffffad890a356868 FS: 00007f5578a2a400(0000) GS:ffff97ed317e1000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f015c70fb18 CR3: 00000001109fd006 CR4: 0000000000f70ef0 PKRU: 55555554 Call Trace: <TASK> xas_store+0x58/0x630 __xa_store+0xa5/0x130 xa_store+0x2c/0x50 kvm_vm_set_mem_attributes+0x343/0x710 [kvm] kvm_vm_ioctl+0x796/0xab0 [kvm] __x64_sys_ioctl+0xa3/0xd0 do_syscall_64+0x8c/0x7a0 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7f5578d031bb Code: ff ff ff 85 c0 79 9b 49 c7 c4 ff ff ff ff 5b 5d 4c 89 e0 41 5c c3 66 0f 1f 84 00 00 00 00 00 f3 0f 1e fa b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 2d 4c 0f 00 f7 d8 64 89 01 48 RSP: 002b:00007ffe0a742b88 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 000000004020aed2 RCX: 00007f5578d031bb RDX: 00007ffe0a742c80 RSI: 000000004020aed2 RDI: 000000000000000b RBP: 0000010000000000 R08: 0000010000000000 R09: 0000017680000000 R10: 0000000000000080 R11: 0000000000000246 R12: 00005575e5f95120 R13: 00007ffe0a742c80 R14: 0000000000000008 R15: 00005575e5f961e0 While looping through the range of memory setting the attributes, call cond_resched() to give the scheduler a chance to run a higher priority task on the runqueue if necessary and avoid staying in kernel mode long enough to trigger the lockup.

In the Linux kernel, the following vulnerability has been resolved: powerpc/imc-pmu: Fix use of mutex in IRQs disabled section Current imc-pmu code triggers a WARNING with CONFIG_DEBUG_ATOMIC_SLEEP and CONFIG_PROVE_LOCKING enabled, while running a thread_imc event. Command to trigger the warning: # perf stat -e thread_imc/CPM_CS_FROM_L4_MEM_X_DPTEG/ sleep 5 Performance counter stats for 'sleep 5': 0 thread_imc/CPM_CS_FROM_L4_MEM_X_DPTEG/ 5.002117947 seconds time elapsed 0.000131000 seconds user 0.001063000 seconds sys Below is snippet of the warning in dmesg: BUG: sleeping function called from invalid context at kernel/locking/mutex.c:580 in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 2869, name: perf-exec preempt_count: 2, expected: 0 4 locks held by perf-exec/2869: #0: c00000004325c540 (&sig->cred_guard_mutex){+.+.}-{3:3}, at: bprm_execve+0x64/0xa90 #1: c00000004325c5d8 (&sig->exec_update_lock){++++}-{3:3}, at: begin_new_exec+0x460/0xef0 #2: c0000003fa99d4e0 (&cpuctx_lock){-...}-{2:2}, at: perf_event_exec+0x290/0x510 #3: c000000017ab8418 (&ctx->lock){....}-{2:2}, at: perf_event_exec+0x29c/0x510 irq event stamp: 4806 hardirqs last enabled at (4805): [<c000000000f65b94>] _raw_spin_unlock_irqrestore+0x94/0xd0 hardirqs last disabled at (4806): [<c0000000003fae44>] perf_event_exec+0x394/0x510 softirqs last enabled at (0): [<c00000000013c404>] copy_process+0xc34/0x1ff0 softirqs last disabled at (0): [<0000000000000000>] 0x0 CPU: 36 PID: 2869 Comm: perf-exec Not tainted 6.2.0-rc2-00011-g1247637727f2 #61 Hardware name: 8375-42A POWER9 0x4e1202 opal:v7.0-16-g9b85f7d961 PowerNV Call Trace: dump_stack_lvl+0x98/0xe0 (unreliable) __might_resched+0x2f8/0x310 __mutex_lock+0x6c/0x13f0 thread_imc_event_add+0xf4/0x1b0 event_sched_in+0xe0/0x210 merge_sched_in+0x1f0/0x600 visit_groups_merge.isra.92.constprop.166+0x2bc/0x6c0 ctx_flexible_sched_in+0xcc/0x140 ctx_sched_in+0x20c/0x2a0 ctx_resched+0x104/0x1c0 perf_event_exec+0x340/0x510 begin_new_exec+0x730/0xef0 load_elf_binary+0x3f8/0x1e10 ... do not call blocking ops when !TASK_RUNNING; state=2001 set at [<00000000fd63e7cf>] do_nanosleep+0x60/0x1a0 WARNING: CPU: 36 PID: 2869 at kernel/sched/core.c:9912 __might_sleep+0x9c/0xb0 CPU: 36 PID: 2869 Comm: sleep Tainted: G W 6.2.0-rc2-00011-g1247637727f2 #61 Hardware name: 8375-42A POWER9 0x4e1202 opal:v7.0-16-g9b85f7d961 PowerNV NIP: c000000000194a1c LR: c000000000194a18 CTR: c000000000a78670 REGS: c00000004d2134e0 TRAP: 0700 Tainted: G W (6.2.0-rc2-00011-g1247637727f2) MSR: 9000000000021033 <SF,HV,ME,IR,DR,RI,LE> CR: 48002824 XER: 00000000 CFAR: c00000000013fb64 IRQMASK: 1 The above warning triggered because the current imc-pmu code uses mutex lock in interrupt disabled sections. The function mutex_lock() internally calls __might_resched(), which will check if IRQs are disabled and in case IRQs are disabled, it will trigger the warning. Fix the issue by changing the mutex lock to spinlock. [mpe: Fix comments, trim oops in change log, add reported-by tags]

In the Linux kernel, the following vulnerability has been resolved: soc/tegra: regulators: Fix locking up when voltage-spread is out of range Fix voltage coupler lockup which happens when voltage-spread is out of range due to a bug in the code. The max-spread requirement shall be accounted when CPU regulator doesn't have consumers. This problem is observed on Tegra30 Ouya game console once system-wide DVFS is enabled in a device-tree.

In the Linux kernel, the following vulnerability has been resolved: mm/swapfile: add cond_resched() in get_swap_pages() The softlockup still occurs in get_swap_pages() under memory pressure. 64 CPU cores, 64GB memory, and 28 zram devices, the disksize of each zram device is 50MB with same priority as si. Use the stress-ng tool to increase memory pressure, causing the system to oom frequently. The plist_for_each_entry_safe() loops in get_swap_pages() could reach tens of thousands of times to find available space (extreme case: cond_resched() is not called in scan_swap_map_slots()). Let's add cond_resched() into get_swap_pages() when failed to find available space to avoid softlockup.

In the Linux kernel, the following vulnerability has been resolved: igb: revert rtnl_lock() that causes deadlock The commit 6faee3d4ee8b ("igb: Add lock to avoid data race") adds rtnl_lock to eliminate a false data race shown below (FREE from device detaching) | (USE from netdev core) igb_remove | igb_ndo_get_vf_config igb_disable_sriov | vf >= adapter->vfs_allocated_count? kfree(adapter->vf_data) | adapter->vfs_allocated_count = 0 | | memcpy(... adapter->vf_data[vf] The above race will never happen and the extra rtnl_lock causes deadlock below [ 141.420169] <TASK> [ 141.420672] __schedule+0x2dd/0x840 [ 141.421427] schedule+0x50/0xc0 [ 141.422041] schedule_preempt_disabled+0x11/0x20 [ 141.422678] __mutex_lock.isra.13+0x431/0x6b0 [ 141.423324] unregister_netdev+0xe/0x20 [ 141.423578] igbvf_remove+0x45/0xe0 [igbvf] [ 141.423791] pci_device_remove+0x36/0xb0 [ 141.423990] device_release_driver_internal+0xc1/0x160 [ 141.424270] pci_stop_bus_device+0x6d/0x90 [ 141.424507] pci_stop_and_remove_bus_device+0xe/0x20 [ 141.424789] pci_iov_remove_virtfn+0xba/0x120 [ 141.425452] sriov_disable+0x2f/0xf0 [ 141.425679] igb_disable_sriov+0x4e/0x100 [igb] [ 141.426353] igb_remove+0xa0/0x130 [igb] [ 141.426599] pci_device_remove+0x36/0xb0 [ 141.426796] device_release_driver_internal+0xc1/0x160 [ 141.427060] driver_detach+0x44/0x90 [ 141.427253] bus_remove_driver+0x55/0xe0 [ 141.427477] pci_unregister_driver+0x2a/0xa0 [ 141.428296] __x64_sys_delete_module+0x141/0x2b0 [ 141.429126] ? mntput_no_expire+0x4a/0x240 [ 141.429363] ? syscall_trace_enter.isra.19+0x126/0x1a0 [ 141.429653] do_syscall_64+0x5b/0x80 [ 141.429847] ? exit_to_user_mode_prepare+0x14d/0x1c0 [ 141.430109] ? syscall_exit_to_user_mode+0x12/0x30 [ 141.430849] ? do_syscall_64+0x67/0x80 [ 141.431083] ? syscall_exit_to_user_mode_prepare+0x183/0x1b0 [ 141.431770] ? syscall_exit_to_user_mode+0x12/0x30 [ 141.432482] ? do_syscall_64+0x67/0x80 [ 141.432714] ? exc_page_fault+0x64/0x140 [ 141.432911] entry_SYSCALL_64_after_hwframe+0x72/0xdc Since the igb_disable_sriov() will call pci_disable_sriov() before releasing any resources, the netdev core will synchronize the cleanup to avoid any races. This patch removes the useless rtnl_(un)lock to guarantee correctness.

In the Linux kernel, the following vulnerability has been resolved: USB: Gadget: core: Help prevent panic during UVC unconfigure Avichal Rakesh reported a kernel panic that occurred when the UVC gadget driver was removed from a gadget's configuration. The panic involves a somewhat complicated interaction between the kernel driver and a userspace component (as described in the Link tag below), but the analysis did make one thing clear: The Gadget core should accomodate gadget drivers calling usb_gadget_deactivate() as part of their unbind procedure. Currently this doesn't work. gadget_unbind_driver() calls driver->unbind() while holding the udc->connect_lock mutex, and usb_gadget_deactivate() attempts to acquire that mutex, which will result in a deadlock. The simple fix is for gadget_unbind_driver() to release the mutex when invoking the ->unbind() callback. There is no particular reason for it to be holding the mutex at that time, and the mutex isn't held while the ->bind() callback is invoked. So we'll drop the mutex before performing the unbind callback and reacquire it afterward. We'll also add a couple of comments to usb_gadget_activate() and usb_gadget_deactivate(). Because they run in process context they must not be called from a gadget driver's ->disconnect() callback, which (according to the kerneldoc for struct usb_gadget_driver in include/linux/usb/gadget.h) may run in interrupt context. This may help prevent similar bugs from arising in the future.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: Fix possible deadlock in rfcomm_sk_state_change syzbot reports a possible deadlock in rfcomm_sk_state_change [1]. While rfcomm_sock_connect acquires the sk lock and waits for the rfcomm lock, rfcomm_sock_release could have the rfcomm lock and hit a deadlock for acquiring the sk lock. Here's a simplified flow: rfcomm_sock_connect: lock_sock(sk) rfcomm_dlc_open: rfcomm_lock() rfcomm_sock_release: rfcomm_sock_shutdown: rfcomm_lock() __rfcomm_dlc_close: rfcomm_k_state_change: lock_sock(sk) This patch drops the sk lock before calling rfcomm_dlc_open to avoid the possible deadlock and holds sk's reference count to prevent use-after-free after rfcomm_dlc_open completes.

In the Linux kernel, the following vulnerability has been resolved: ptdma: pt_core_execute_cmd() should use spinlock The interrupt handler (pt_core_irq_handler()) of the ptdma driver can be called from interrupt context. The code flow in this function can lead down to pt_core_execute_cmd() which will attempt to grab a mutex, which is not appropriate in interrupt context and ultimately leads to a kernel panic. The fix here changes this mutex to a spinlock, which has been verified to resolve the issue.

In the Linux kernel, the following vulnerability has been resolved: gpio: xilinx: Convert gpio_lock to raw spinlock irq_chip functions may be called in raw spinlock context. Therefore, we must also use a raw spinlock for our own internal locking. This fixes the following lockdep splat: [ 5.349336] ============================= [ 5.353349] [ BUG: Invalid wait context ] [ 5.357361] 6.13.0-rc5+ #69 Tainted: G W [ 5.363031] ----------------------------- [ 5.367045] kworker/u17:1/44 is trying to lock: [ 5.371587] ffffff88018b02c0 (&chip->gpio_lock){....}-{3:3}, at: xgpio_irq_unmask (drivers/gpio/gpio-xilinx.c:433 (discriminator 8)) [ 5.380079] other info that might help us debug this: [ 5.385138] context-{5:5} [ 5.387762] 5 locks held by kworker/u17:1/44: [ 5.392123] #0: ffffff8800014958 ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_one_work (kernel/workqueue.c:3204) [ 5.402260] #1: ffffffc082fcbdd8 (deferred_probe_work){+.+.}-{0:0}, at: process_one_work (kernel/workqueue.c:3205) [ 5.411528] #2: ffffff880172c900 (&dev->mutex){....}-{4:4}, at: __device_attach (drivers/base/dd.c:1006) [ 5.419929] #3: ffffff88039c8268 (request_class#2){+.+.}-{4:4}, at: __setup_irq (kernel/irq/internals.h:156 kernel/irq/manage.c:1596) [ 5.428331] #4: ffffff88039c80c8 (lock_class#2){....}-{2:2}, at: __setup_irq (kernel/irq/manage.c:1614) [ 5.436472] stack backtrace: [ 5.439359] CPU: 2 UID: 0 PID: 44 Comm: kworker/u17:1 Tainted: G W 6.13.0-rc5+ #69 [ 5.448690] Tainted: [W]=WARN [ 5.451656] Hardware name: xlnx,zynqmp (DT) [ 5.455845] Workqueue: events_unbound deferred_probe_work_func [ 5.461699] Call trace: [ 5.464147] show_stack+0x18/0x24 C [ 5.467821] dump_stack_lvl (lib/dump_stack.c:123) [ 5.471501] dump_stack (lib/dump_stack.c:130) [ 5.474824] __lock_acquire (kernel/locking/lockdep.c:4828 kernel/locking/lockdep.c:4898 kernel/locking/lockdep.c:5176) [ 5.478758] lock_acquire (arch/arm64/include/asm/percpu.h:40 kernel/locking/lockdep.c:467 kernel/locking/lockdep.c:5851 kernel/locking/lockdep.c:5814) [ 5.482429] _raw_spin_lock_irqsave (include/linux/spinlock_api_smp.h:111 kernel/locking/spinlock.c:162) [ 5.486797] xgpio_irq_unmask (drivers/gpio/gpio-xilinx.c:433 (discriminator 8)) [ 5.490737] irq_enable (kernel/irq/internals.h:236 kernel/irq/chip.c:170 kernel/irq/chip.c:439 kernel/irq/chip.c:432 kernel/irq/chip.c:345) [ 5.494060] __irq_startup (kernel/irq/internals.h:241 kernel/irq/chip.c:180 kernel/irq/chip.c:250) [ 5.497645] irq_startup (kernel/irq/chip.c:270) [ 5.501143] __setup_irq (kernel/irq/manage.c:1807) [ 5.504728] request_threaded_irq (kernel/irq/manage.c:2208)

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: avoid deadlock between hci_dev->lock and socket lock Commit eab2404ba798 ("Bluetooth: Add BT_PHY socket option") added a dependency between socket lock and hci_dev->lock that could lead to deadlock. It turns out that hci_conn_get_phy() is not in any way relying on hdev being immutable during the runtime of this function, neither does it even look at any of the members of hdev, and as such there is no need to hold that lock. This fixes the lockdep splat below: ====================================================== WARNING: possible circular locking dependency detected 5.12.0-rc1-00026-g73d464503354 #10 Not tainted ------------------------------------------------------ bluetoothd/1118 is trying to acquire lock: ffff8f078383c078 (&hdev->lock){+.+.}-{3:3}, at: hci_conn_get_phy+0x1c/0x150 [bluetooth] but task is already holding lock: ffff8f07e831d920 (sk_lock-AF_BLUETOOTH-BTPROTO_L2CAP){+.+.}-{0:0}, at: l2cap_sock_getsockopt+0x8b/0x610 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #3 (sk_lock-AF_BLUETOOTH-BTPROTO_L2CAP){+.+.}-{0:0}: lock_sock_nested+0x72/0xa0 l2cap_sock_ready_cb+0x18/0x70 [bluetooth] l2cap_config_rsp+0x27a/0x520 [bluetooth] l2cap_sig_channel+0x658/0x1330 [bluetooth] l2cap_recv_frame+0x1ba/0x310 [bluetooth] hci_rx_work+0x1cc/0x640 [bluetooth] process_one_work+0x244/0x5f0 worker_thread+0x3c/0x380 kthread+0x13e/0x160 ret_from_fork+0x22/0x30 -> #2 (&chan->lock#2/1){+.+.}-{3:3}: __mutex_lock+0xa3/0xa10 l2cap_chan_connect+0x33a/0x940 [bluetooth] l2cap_sock_connect+0x141/0x2a0 [bluetooth] __sys_connect+0x9b/0xc0 __x64_sys_connect+0x16/0x20 do_syscall_64+0x33/0x80 entry_SYSCALL_64_after_hwframe+0x44/0xae -> #1 (&conn->chan_lock){+.+.}-{3:3}: __mutex_lock+0xa3/0xa10 l2cap_chan_connect+0x322/0x940 [bluetooth] l2cap_sock_connect+0x141/0x2a0 [bluetooth] __sys_connect+0x9b/0xc0 __x64_sys_connect+0x16/0x20 do_syscall_64+0x33/0x80 entry_SYSCALL_64_after_hwframe+0x44/0xae -> #0 (&hdev->lock){+.+.}-{3:3}: __lock_acquire+0x147a/0x1a50 lock_acquire+0x277/0x3d0 __mutex_lock+0xa3/0xa10 hci_conn_get_phy+0x1c/0x150 [bluetooth] l2cap_sock_getsockopt+0x5a9/0x610 [bluetooth] __sys_getsockopt+0xcc/0x200 __x64_sys_getsockopt+0x20/0x30 do_syscall_64+0x33/0x80 entry_SYSCALL_64_after_hwframe+0x44/0xae other info that might help us debug this: Chain exists of: &hdev->lock --> &chan->lock#2/1 --> sk_lock-AF_BLUETOOTH-BTPROTO_L2CAP Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(sk_lock-AF_BLUETOOTH-BTPROTO_L2CAP); lock(&chan->lock#2/1); lock(sk_lock-AF_BLUETOOTH-BTPROTO_L2CAP); lock(&hdev->lock); *** DEADLOCK *** 1 lock held by bluetoothd/1118: #0: ffff8f07e831d920 (sk_lock-AF_BLUETOOTH-BTPROTO_L2CAP){+.+.}-{0:0}, at: l2cap_sock_getsockopt+0x8b/0x610 [bluetooth] stack backtrace: CPU: 3 PID: 1118 Comm: bluetoothd Not tainted 5.12.0-rc1-00026-g73d464503354 #10 Hardware name: LENOVO 20K5S22R00/20K5S22R00, BIOS R0IET38W (1.16 ) 05/31/2017 Call Trace: dump_stack+0x7f/0xa1 check_noncircular+0x105/0x120 ? __lock_acquire+0x147a/0x1a50 __lock_acquire+0x147a/0x1a50 lock_acquire+0x277/0x3d0 ? hci_conn_get_phy+0x1c/0x150 [bluetooth] ? __lock_acquire+0x2e1/0x1a50 ? lock_is_held_type+0xb4/0x120 ? hci_conn_get_phy+0x1c/0x150 [bluetooth] __mutex_lock+0xa3/0xa10 ? hci_conn_get_phy+0x1c/0x150 [bluetooth] ? lock_acquire+0x277/0x3d0 ? mark_held_locks+0x49/0x70 ? mark_held_locks+0x49/0x70 ? hci_conn_get_phy+0x1c/0x150 [bluetooth] hci_conn_get_phy+0x ---truncated---

In the Linux kernel, the following vulnerability has been resolved: can: j1939: prevent deadlock by changing j1939_socks_lock to rwlock The following 3 locks would race against each other, causing the deadlock situation in the Syzbot bug report: - j1939_socks_lock - active_session_list_lock - sk_session_queue_lock A reasonable fix is to change j1939_socks_lock to an rwlock, since in the rare situations where a write lock is required for the linked list that j1939_socks_lock is protecting, the code does not attempt to acquire any more locks. This would break the circular lock dependency, where, for example, the current thread already locks j1939_socks_lock and attempts to acquire sk_session_queue_lock, and at the same time, another thread attempts to acquire j1939_socks_lock while holding sk_session_queue_lock. NOTE: This patch along does not fix the unregister_netdevice bug reported by Syzbot; instead, it solves a deadlock situation to prepare for one or more further patches to actually fix the Syzbot bug, which appears to be a reference counting problem within the j1939 codebase. [mkl: remove unrelated newline change]

In the Linux kernel, the following vulnerability has been resolved: batman-adv: Avoid double-rtnl_lock ELP metric worker batadv_v_elp_get_throughput() might be called when the RTNL lock is already held. This could be problematic when the work queue item is cancelled via cancel_delayed_work_sync() in batadv_v_elp_iface_disable(). In this case, an rtnl_lock() would cause a deadlock. To avoid this, rtnl_trylock() was used in this function to skip the retrieval of the ethtool information in case the RTNL lock was already held. But for cfg80211 interfaces, batadv_get_real_netdev() was called - which also uses rtnl_lock(). The approach for __ethtool_get_link_ksettings() must also be used instead and the lockless version __batadv_get_real_netdev() has to be called.

In the Linux kernel, the following vulnerability has been resolved: ceph: fix deadlock or deadcode of misusing dget() The lock order is incorrect between denty and its parent, we should always make sure that the parent get the lock first. But since this deadcode is never used and the parent dir will always be set from the callers, let's just remove it.

In the Linux kernel, the following vulnerability has been resolved: dma-debug: don't call __dma_entry_alloc_check_leak() under free_entries_lock __dma_entry_alloc_check_leak() calls into printk -> serial console output (qcom geni) and grabs port->lock under free_entries_lock spin lock, which is a reverse locking dependency chain as qcom_geni IRQ handler can call into dma-debug code and grab free_entries_lock under port->lock. Move __dma_entry_alloc_check_leak() call out of free_entries_lock scope so that we don't acquire serial console's port->lock under it. Trimmed-down lockdep splat: The existing dependency chain (in reverse order) is: -> #2 (free_entries_lock){-.-.}-{2:2}: _raw_spin_lock_irqsave+0x60/0x80 dma_entry_alloc+0x38/0x110 debug_dma_map_page+0x60/0xf8 dma_map_page_attrs+0x1e0/0x230 dma_map_single_attrs.constprop.0+0x6c/0xc8 geni_se_rx_dma_prep+0x40/0xcc qcom_geni_serial_isr+0x310/0x510 __handle_irq_event_percpu+0x110/0x244 handle_irq_event_percpu+0x20/0x54 handle_irq_event+0x50/0x88 handle_fasteoi_irq+0xa4/0xcc handle_irq_desc+0x28/0x40 generic_handle_domain_irq+0x24/0x30 gic_handle_irq+0xc4/0x148 do_interrupt_handler+0xa4/0xb0 el1_interrupt+0x34/0x64 el1h_64_irq_handler+0x18/0x24 el1h_64_irq+0x64/0x68 arch_local_irq_enable+0x4/0x8 ____do_softirq+0x18/0x24 ... -> #1 (&port_lock_key){-.-.}-{2:2}: _raw_spin_lock_irqsave+0x60/0x80 qcom_geni_serial_console_write+0x184/0x1dc console_flush_all+0x344/0x454 console_unlock+0x94/0xf0 vprintk_emit+0x238/0x24c vprintk_default+0x3c/0x48 vprintk+0xb4/0xbc _printk+0x68/0x90 register_console+0x230/0x38c uart_add_one_port+0x338/0x494 qcom_geni_serial_probe+0x390/0x424 platform_probe+0x70/0xc0 really_probe+0x148/0x280 __driver_probe_device+0xfc/0x114 driver_probe_device+0x44/0x100 __device_attach_driver+0x64/0xdc bus_for_each_drv+0xb0/0xd8 __device_attach+0xe4/0x140 device_initial_probe+0x1c/0x28 bus_probe_device+0x44/0xb0 device_add+0x538/0x668 of_device_add+0x44/0x50 of_platform_device_create_pdata+0x94/0xc8 of_platform_bus_create+0x270/0x304 of_platform_populate+0xac/0xc4 devm_of_platform_populate+0x60/0xac geni_se_probe+0x154/0x160 platform_probe+0x70/0xc0 ... -> #0 (console_owner){-...}-{0:0}: __lock_acquire+0xdf8/0x109c lock_acquire+0x234/0x284 console_flush_all+0x330/0x454 console_unlock+0x94/0xf0 vprintk_emit+0x238/0x24c vprintk_default+0x3c/0x48 vprintk+0xb4/0xbc _printk+0x68/0x90 dma_entry_alloc+0xb4/0x110 debug_dma_map_sg+0xdc/0x2f8 __dma_map_sg_attrs+0xac/0xe4 dma_map_sgtable+0x30/0x4c get_pages+0x1d4/0x1e4 [msm] msm_gem_pin_pages_locked+0x38/0xac [msm] msm_gem_pin_vma_locked+0x58/0x88 [msm] msm_ioctl_gem_submit+0xde4/0x13ac [msm] drm_ioctl_kernel+0xe0/0x15c drm_ioctl+0x2e8/0x3f4 vfs_ioctl+0x30/0x50 ... Chain exists of: console_owner --> &port_lock_key --> free_entries_lock Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(free_entries_lock); lock(&port_lock_key); lock(free_entries_lock); lock(console_owner); *** DEADLOCK *** Call trace: dump_backtrace+0xb4/0xf0 show_stack+0x20/0x30 dump_stack_lvl+0x60/0x84 dump_stack+0x18/0x24 print_circular_bug+0x1cc/0x234 check_noncircular+0x78/0xac __lock_acquire+0xdf8/0x109c lock_acquire+0x234/0x284 console_flush_all+0x330/0x454 consol ---truncated---

In the Linux kernel, the following vulnerability has been resolved: drm: Don't unref the same fb many times by mistake due to deadlock handling If we get a deadlock after the fb lookup in drm_mode_page_flip_ioctl() we proceed to unref the fb and then retry the whole thing from the top. But we forget to reset the fb pointer back to NULL, and so if we then get another error during the retry, before the fb lookup, we proceed the unref the same fb again without having gotten another reference. The end result is that the fb will (eventually) end up being freed while it's still in use. Reset fb to NULL once we've unreffed it to avoid doing it again until we've done another fb lookup. This turned out to be pretty easy to hit on a DG2 when doing async flips (and CONFIG_DEBUG_WW_MUTEX_SLOWPATH=y). The first symptom I saw that drm_closefb() simply got stuck in a busy loop while walking the framebuffer list. Fortunately I was able to convince it to oops instead, and from there it was easier to track down the culprit.

In the Linux kernel, the following vulnerability has been resolved: KVM: arm64: Fix circular locking dependency The rule inside kvm enforces that the vcpu->mutex is taken *inside* kvm->lock. The rule is violated by the pkvm_create_hyp_vm() which acquires the kvm->lock while already holding the vcpu->mutex lock from kvm_vcpu_ioctl(). Avoid the circular locking dependency altogether by protecting the hyp vm handle with the config_lock, much like we already do for other forms of VM-scoped data.

In the Linux kernel, the following vulnerability has been resolved: nfsd: fix RELEASE_LOCKOWNER The test on so_count in nfsd4_release_lockowner() is nonsense and harmful. Revert to using check_for_locks(), changing that to not sleep. First: harmful. As is documented in the kdoc comment for nfsd4_release_lockowner(), the test on so_count can transiently return a false positive resulting in a return of NFS4ERR_LOCKS_HELD when in fact no locks are held. This is clearly a protocol violation and with the Linux NFS client it can cause incorrect behaviour. If RELEASE_LOCKOWNER is sent while some other thread is still processing a LOCK request which failed because, at the time that request was received, the given owner held a conflicting lock, then the nfsd thread processing that LOCK request can hold a reference (conflock) to the lock owner that causes nfsd4_release_lockowner() to return an incorrect error. The Linux NFS client ignores that NFS4ERR_LOCKS_HELD error because it never sends NFS4_RELEASE_LOCKOWNER without first releasing any locks, so it knows that the error is impossible. It assumes the lock owner was in fact released so it feels free to use the same lock owner identifier in some later locking request. When it does reuse a lock owner identifier for which a previous RELEASE failed, it will naturally use a lock_seqid of zero. However the server, which didn't release the lock owner, will expect a larger lock_seqid and so will respond with NFS4ERR_BAD_SEQID. So clearly it is harmful to allow a false positive, which testing so_count allows. The test is nonsense because ... well... it doesn't mean anything. so_count is the sum of three different counts. 1/ the set of states listed on so_stateids 2/ the set of active vfs locks owned by any of those states 3/ various transient counts such as for conflicting locks. When it is tested against '2' it is clear that one of these is the transient reference obtained by find_lockowner_str_locked(). It is not clear what the other one is expected to be. In practice, the count is often 2 because there is precisely one state on so_stateids. If there were more, this would fail. In my testing I see two circumstances when RELEASE_LOCKOWNER is called. In one case, CLOSE is called before RELEASE_LOCKOWNER. That results in all the lock states being removed, and so the lockowner being discarded (it is removed when there are no more references which usually happens when the lock state is discarded). When nfsd4_release_lockowner() finds that the lock owner doesn't exist, it returns success. The other case shows an so_count of '2' and precisely one state listed in so_stateid. It appears that the Linux client uses a separate lock owner for each file resulting in one lock state per lock owner, so this test on '2' is safe. For another client it might not be safe. So this patch changes check_for_locks() to use the (newish) find_any_file_locked() so that it doesn't take a reference on the nfs4_file and so never calls nfsd_file_put(), and so never sleeps. With this check is it safe to restore the use of check_for_locks() rather than testing so_count against the mysterious '2'.

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix hang in nilfs_lookup_dirty_data_buffers() Syzbot reported a hang issue in migrate_pages_batch() called by mbind() and nilfs_lookup_dirty_data_buffers() called in the log writer of nilfs2. While migrate_pages_batch() locks a folio and waits for the writeback to complete, the log writer thread that should bring the writeback to completion picks up the folio being written back in nilfs_lookup_dirty_data_buffers() that it calls for subsequent log creation and was trying to lock the folio. Thus causing a deadlock. In the first place, it is unexpected that folios/pages in the middle of writeback will be updated and become dirty. Nilfs2 adds a checksum to verify the validity of the log being written and uses it for recovery at mount, so data changes during writeback are suppressed. Since this is broken, an unclean shutdown could potentially cause recovery to fail. Investigation revealed that the root cause is that the wait for writeback completion in nilfs_page_mkwrite() is conditional, and if the backing device does not require stable writes, data may be modified without waiting. Fix these issues by making nilfs_page_mkwrite() wait for writeback to finish regardless of the stable write requirement of the backing device.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: iso: Fix circular lock in iso_listen_bis This fixes the circular locking dependency warning below, by releasing the socket lock before enterning iso_listen_bis, to avoid any potential deadlock with hdev lock. [ 75.307983] ====================================================== [ 75.307984] WARNING: possible circular locking dependency detected [ 75.307985] 6.12.0-rc6+ #22 Not tainted [ 75.307987] ------------------------------------------------------ [ 75.307987] kworker/u81:2/2623 is trying to acquire lock: [ 75.307988] ffff8fde1769da58 (sk_lock-AF_BLUETOOTH-BTPROTO_ISO) at: iso_connect_cfm+0x253/0x840 [bluetooth] [ 75.308021] but task is already holding lock: [ 75.308022] ffff8fdd61a10078 (&hdev->lock) at: hci_le_per_adv_report_evt+0x47/0x2f0 [bluetooth] [ 75.308053] which lock already depends on the new lock. [ 75.308054] the existing dependency chain (in reverse order) is: [ 75.308055] -> #1 (&hdev->lock){+.+.}-{3:3}: [ 75.308057] __mutex_lock+0xad/0xc50 [ 75.308061] mutex_lock_nested+0x1b/0x30 [ 75.308063] iso_sock_listen+0x143/0x5c0 [bluetooth] [ 75.308085] __sys_listen_socket+0x49/0x60 [ 75.308088] __x64_sys_listen+0x4c/0x90 [ 75.308090] x64_sys_call+0x2517/0x25f0 [ 75.308092] do_syscall_64+0x87/0x150 [ 75.308095] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 75.308098] -> #0 (sk_lock-AF_BLUETOOTH-BTPROTO_ISO){+.+.}-{0:0}: [ 75.308100] __lock_acquire+0x155e/0x25f0 [ 75.308103] lock_acquire+0xc9/0x300 [ 75.308105] lock_sock_nested+0x32/0x90 [ 75.308107] iso_connect_cfm+0x253/0x840 [bluetooth] [ 75.308128] hci_connect_cfm+0x6c/0x190 [bluetooth] [ 75.308155] hci_le_per_adv_report_evt+0x27b/0x2f0 [bluetooth] [ 75.308180] hci_le_meta_evt+0xe7/0x200 [bluetooth] [ 75.308206] hci_event_packet+0x21f/0x5c0 [bluetooth] [ 75.308230] hci_rx_work+0x3ae/0xb10 [bluetooth] [ 75.308254] process_one_work+0x212/0x740 [ 75.308256] worker_thread+0x1bd/0x3a0 [ 75.308258] kthread+0xe4/0x120 [ 75.308259] ret_from_fork+0x44/0x70 [ 75.308261] ret_from_fork_asm+0x1a/0x30 [ 75.308263] other info that might help us debug this: [ 75.308264] Possible unsafe locking scenario: [ 75.308264] CPU0 CPU1 [ 75.308265] ---- ---- [ 75.308265] lock(&hdev->lock); [ 75.308267] lock(sk_lock- AF_BLUETOOTH-BTPROTO_ISO); [ 75.308268] lock(&hdev->lock); [ 75.308269] lock(sk_lock-AF_BLUETOOTH-BTPROTO_ISO); [ 75.308270] *** DEADLOCK *** [ 75.308271] 4 locks held by kworker/u81:2/2623: [ 75.308272] #0: ffff8fdd66e52148 ((wq_completion)hci0#2){+.+.}-{0:0}, at: process_one_work+0x443/0x740 [ 75.308276] #1: ffffafb488b7fe48 ((work_completion)(&hdev->rx_work)), at: process_one_work+0x1ce/0x740 [ 75.308280] #2: ffff8fdd61a10078 (&hdev->lock){+.+.}-{3:3} at: hci_le_per_adv_report_evt+0x47/0x2f0 [bluetooth] [ 75.308304] #3: ffffffffb6ba4900 (rcu_read_lock){....}-{1:2}, at: hci_connect_cfm+0x29/0x190 [bluetooth]

In the Linux kernel, the following vulnerability has been resolved: rhashtable: Fix potential deadlock by moving schedule_work outside lock Move the hash table growth check and work scheduling outside the rht lock to prevent a possible circular locking dependency. The original implementation could trigger a lockdep warning due to a potential deadlock scenario involving nested locks between rhashtable bucket, rq lock, and dsq lock. By relocating the growth check and work scheduling after releasing the rth lock, we break this potential deadlock chain. This change expands the flexibility of rhashtable by removing restrictive locking that previously limited its use in scheduler and workqueue contexts. Import to say that this calls rht_grow_above_75(), which reads from struct rhashtable without holding the lock, if this is a problem, we can move the check to the lock, and schedule the workqueue after the lock. Modified so that atomic_inc is also moved outside of the bucket lock along with the growth above 75% check.

In the Linux kernel, the following vulnerability has been resolved: ptr_ring: do not block hard interrupts in ptr_ring_resize_multiple() Jakub added a lockdep_assert_no_hardirq() check in __page_pool_put_page() to increase test coverage. syzbot found a splat caused by hard irq blocking in ptr_ring_resize_multiple() [1] As current users of ptr_ring_resize_multiple() do not require hard irqs being masked, replace it to only block BH. Rename helpers to better reflect they are safe against BH only. - ptr_ring_resize_multiple() to ptr_ring_resize_multiple_bh() - skb_array_resize_multiple() to skb_array_resize_multiple_bh() [1] WARNING: CPU: 1 PID: 9150 at net/core/page_pool.c:709 __page_pool_put_page net/core/page_pool.c:709 [inline] WARNING: CPU: 1 PID: 9150 at net/core/page_pool.c:709 page_pool_put_unrefed_netmem+0x157/0xa40 net/core/page_pool.c:780 Modules linked in: CPU: 1 UID: 0 PID: 9150 Comm: syz.1.1052 Not tainted 6.11.0-rc3-syzkaller-00202-gf8669d7b5f5d #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/06/2024 RIP: 0010:__page_pool_put_page net/core/page_pool.c:709 [inline] RIP: 0010:page_pool_put_unrefed_netmem+0x157/0xa40 net/core/page_pool.c:780 Code: 74 0e e8 7c aa fb f7 eb 43 e8 75 aa fb f7 eb 3c 65 8b 1d 38 a8 6a 76 31 ff 89 de e8 a3 ae fb f7 85 db 74 0b e8 5a aa fb f7 90 <0f> 0b 90 eb 1d 65 8b 1d 15 a8 6a 76 31 ff 89 de e8 84 ae fb f7 85 RSP: 0018:ffffc9000bda6b58 EFLAGS: 00010083 RAX: ffffffff8997e523 RBX: 0000000000000000 RCX: 0000000000040000 RDX: ffffc9000fbd0000 RSI: 0000000000001842 RDI: 0000000000001843 RBP: 0000000000000000 R08: ffffffff8997df2c R09: 1ffffd40003a000d R10: dffffc0000000000 R11: fffff940003a000e R12: ffffea0001d00040 R13: ffff88802e8a4000 R14: dffffc0000000000 R15: 00000000ffffffff FS: 00007fb7aaf716c0(0000) GS:ffff8880b9300000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fa15a0d4b72 CR3: 00000000561b0000 CR4: 00000000003506f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> tun_ptr_free drivers/net/tun.c:617 [inline] __ptr_ring_swap_queue include/linux/ptr_ring.h:571 [inline] ptr_ring_resize_multiple_noprof include/linux/ptr_ring.h:643 [inline] tun_queue_resize drivers/net/tun.c:3694 [inline] tun_device_event+0xaaf/0x1080 drivers/net/tun.c:3714 notifier_call_chain+0x19f/0x3e0 kernel/notifier.c:93 call_netdevice_notifiers_extack net/core/dev.c:2032 [inline] call_netdevice_notifiers net/core/dev.c:2046 [inline] dev_change_tx_queue_len+0x158/0x2a0 net/core/dev.c:9024 do_setlink+0xff6/0x41f0 net/core/rtnetlink.c:2923 rtnl_setlink+0x40d/0x5a0 net/core/rtnetlink.c:3201 rtnetlink_rcv_msg+0x73f/0xcf0 net/core/rtnetlink.c:6647 netlink_rcv_skb+0x1e3/0x430 net/netlink/af_netlink.c:2550

In the Linux kernel, the following vulnerability has been resolved: media: uvcvideo: Fix deadlock during uvc_probe If uvc_probe() fails, it can end up calling uvc_status_unregister() before uvc_status_init() is called. Fix this by checking if dev->status is NULL or not in uvc_status_unregister().

In the Linux kernel, the following vulnerability has been resolved: usb: musb: Fix hardware lockup on first Rx endpoint request There is a possibility that a request's callback could be invoked from usb_ep_queue() (call trace below, supplemented with missing calls): req->complete from usb_gadget_giveback_request (drivers/usb/gadget/udc/core.c:999) usb_gadget_giveback_request from musb_g_giveback (drivers/usb/musb/musb_gadget.c:147) musb_g_giveback from rxstate (drivers/usb/musb/musb_gadget.c:784) rxstate from musb_ep_restart (drivers/usb/musb/musb_gadget.c:1169) musb_ep_restart from musb_ep_restart_resume_work (drivers/usb/musb/musb_gadget.c:1176) musb_ep_restart_resume_work from musb_queue_resume_work (drivers/usb/musb/musb_core.c:2279) musb_queue_resume_work from musb_gadget_queue (drivers/usb/musb/musb_gadget.c:1241) musb_gadget_queue from usb_ep_queue (drivers/usb/gadget/udc/core.c:300) According to the docstring of usb_ep_queue(), this should not happen: "Note that @req's ->complete() callback must never be called from within usb_ep_queue() as that can create deadlock situations." In fact, a hardware lockup might occur in the following sequence: 1. The gadget is initialized using musb_gadget_enable(). 2. Meanwhile, a packet arrives, and the RXPKTRDY flag is set, raising an interrupt. 3. If IRQs are enabled, the interrupt is handled, but musb_g_rx() finds an empty queue (next_request() returns NULL). The interrupt flag has already been cleared by the glue layer handler, but the RXPKTRDY flag remains set. 4. The first request is enqueued using usb_ep_queue(), leading to the call of req->complete(), as shown in the call trace above. 5. If the callback enables IRQs and another packet is waiting, step (3) repeats. The request queue is empty because usb_g_giveback() removes the request before invoking the callback. 6. The endpoint remains locked up, as the interrupt triggered by hardware setting the RXPKTRDY flag has been handled, but the flag itself remains set. For this scenario to occur, it is only necessary for IRQs to be enabled at some point during the complete callback. This happens with the USB Ethernet gadget, whose rx_complete() callback calls netif_rx(). If called in the task context, netif_rx() disables the bottom halves (BHs). When the BHs are re-enabled, IRQs are also enabled to allow soft IRQs to be processed. The gadget itself is initialized at module load (or at boot if built-in), but the first request is enqueued when the network interface is brought up, triggering rx_complete() in the task context via ioctl(). If a packet arrives while the interface is down, it can prevent the interface from receiving any further packets from the USB host. The situation is quite complicated with many parties involved. This particular issue can be resolved in several possible ways: 1. Ensure that callbacks never enable IRQs. This would be difficult to enforce, as discovering how netif_rx() interacts with interrupts was already quite challenging and u_ether is not the only function driver. Similar "bugs" could be hidden in other drivers as well. 2. Disable MUSB interrupts in musb_g_giveback() before calling the callback and re-enable them afterwars (by calling musb_{dis,en}able_interrupts(), for example). This would ensure that MUSB interrupts are not handled during the callback, even if IRQs are enabled. In fact, it would allow IRQs to be enabled when releasing the lock. However, this feels like an inelegant hack. 3. Modify the interrupt handler to clear the RXPKTRDY flag if the request queue is empty. While this approach also feels like a hack, it wastes CPU time by attempting to handle incoming packets when the software is not ready to process them. 4. Flush the Rx FIFO instead of calling rxstate() in musb_ep_restart(). This ensures that the hardware can receive packets when there is at least one request in the queue. Once I ---truncated---

In the Linux kernel, the following vulnerability has been resolved: pinctrl: mcp23s08: Fix sleeping in atomic context due to regmap locking If a device uses MCP23xxx IO expander to receive IRQs, the following bug can happen: BUG: sleeping function called from invalid context at kernel/locking/mutex.c:283 in_atomic(): 1, irqs_disabled(): 1, non_block: 0, ... preempt_count: 1, expected: 0 ... Call Trace: ... __might_resched+0x104/0x10e __might_sleep+0x3e/0x62 mutex_lock+0x20/0x4c regmap_lock_mutex+0x10/0x18 regmap_update_bits_base+0x2c/0x66 mcp23s08_irq_set_type+0x1ae/0x1d6 __irq_set_trigger+0x56/0x172 __setup_irq+0x1e6/0x646 request_threaded_irq+0xb6/0x160 ... We observed the problem while experimenting with a touchscreen driver which used MCP23017 IO expander (I2C). The regmap in the pinctrl-mcp23s08 driver uses a mutex for protection from concurrent accesses, which is the default for regmaps without .fast_io, .disable_locking, etc. mcp23s08_irq_set_type() calls regmap_update_bits_base(), and the latter locks the mutex. However, __setup_irq() locks desc->lock spinlock before calling these functions. As a result, the system tries to lock the mutex whole holding the spinlock. It seems, the internal regmap locks are not needed in this driver at all. mcp->lock seems to protect the regmap from concurrent accesses already, except, probably, in mcp_pinconf_get/set. mcp23s08_irq_set_type() and mcp23s08_irq_mask/unmask() are called under chip_bus_lock(), which calls mcp23s08_irq_bus_lock(). The latter takes mcp->lock and enables regmap caching, so that the potentially slow I2C accesses are deferred until chip_bus_unlock(). The accesses to the regmap from mcp23s08_probe_one() do not need additional locking. In all remaining places where the regmap is accessed, except mcp_pinconf_get/set(), the driver already takes mcp->lock. This patch adds locking in mcp_pinconf_get/set() and disables internal locking in the regmap config. Among other things, it fixes the sleeping in atomic context described above.

In the Linux kernel, the following vulnerability has been resolved: bpf: fix recursive lock when verdict program return SK_PASS When the stream_verdict program returns SK_PASS, it places the received skb into its own receive queue, but a recursive lock eventually occurs, leading to an operating system deadlock. This issue has been present since v6.9. ''' sk_psock_strp_data_ready write_lock_bh(&sk->sk_callback_lock) strp_data_ready strp_read_sock read_sock -> tcp_read_sock strp_recv cb.rcv_msg -> sk_psock_strp_read # now stream_verdict return SK_PASS without peer sock assign __SK_PASS = sk_psock_map_verd(SK_PASS, NULL) sk_psock_verdict_apply sk_psock_skb_ingress_self sk_psock_skb_ingress_enqueue sk_psock_data_ready read_lock_bh(&sk->sk_callback_lock) <= dead lock ''' This topic has been discussed before, but it has not been fixed. Previous discussion: https://lore.kernel.org/all/6684a5864ec86_403d20898@john.notmuch

In the Linux kernel, the following vulnerability has been resolved: scsi: megaraid_sas: Fix for a potential deadlock This fixes a 'possible circular locking dependency detected' warning CPU0 CPU1 ---- ---- lock(&instance->reset_mutex); lock(&shost->scan_mutex); lock(&instance->reset_mutex); lock(&shost->scan_mutex); Fix this by temporarily releasing the reset_mutex.

In the Linux kernel, the following vulnerability has been resolved: LoongArch: Fix potential ADE in loongson_gpu_fixup_dma_hang() The switch case in loongson_gpu_fixup_dma_hang() may not DC2 or DC3, and readl(crtc_reg) will access with random address, because the "device" is from "base+PCI_DEVICE_ID", "base" is from "pdev->devfn+1". This is wrong when my platform inserts a discrete GPU: lspci -tv -[0000:00]-+-00.0 Loongson Technology LLC Hyper Transport Bridge Controller ... +-06.0 Loongson Technology LLC LG100 GPU +-06.2 Loongson Technology LLC Device 7a37 ... Add a default switch case to fix the panic as below: Kernel ade access[#1]: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.6.136-loong64-desktop-hwe+ #4 pc 90000000017e5534 ra 90000000017e54c0 tp 90000001002f8000 sp 90000001002fb6c0 a0 80000efe00003100 a1 0000000000003100 a2 0000000000000000 a3 0000000000000002 a4 90000001002fb6b4 a5 900000087cdb58fd a6 90000000027af000 a7 0000000000000001 t0 00000000000085b9 t1 000000000000ffff t2 0000000000000000 t3 0000000000000000 t4 fffffffffffffffd t5 00000000fffb6d9c t6 0000000000083b00 t7 00000000000070c0 t8 900000087cdb4d94 u0 900000087cdb58fd s9 90000001002fb826 s0 90000000031c12c8 s1 7fffffffffffff00 s2 90000000031c12d0 s3 0000000000002710 s4 0000000000000000 s5 0000000000000000 s6 9000000100053000 s7 7fffffffffffff00 s8 90000000030d4000 ra: 90000000017e54c0 loongson_gpu_fixup_dma_hang+0x40/0x210 ERA: 90000000017e5534 loongson_gpu_fixup_dma_hang+0xb4/0x210 CRMD: 000000b0 (PLV0 -IE -DA +PG DACF=CC DACM=CC -WE) PRMD: 00000004 (PPLV0 +PIE -PWE) EUEN: 00000000 (-FPE -SXE -ASXE -BTE) ECFG: 00071c1d (LIE=0,2-4,10-12 VS=7) ESTAT: 00480000 [ADEM] (IS= ECode=8 EsubCode=1) BADV: 7fffffffffffff00 PRID: 0014d000 (Loongson-64bit, Loongson-3A6000-HV) Modules linked in: Process swapper/0 (pid: 1, threadinfo=(____ptrval____), task=(____ptrval____)) Stack : 0000000000000006 90000001002fb778 90000001002fb704 0000000000000007 0000000016a65700 90000000017e5690 000000000000ffff ffffffffffffffff 900000000209f7c0 9000000100053000 900000000209f7a8 9000000000eebc08 0000000000000000 0000000000000000 0000000000000006 90000001002fb778 90000001000530b8 90000000027af000 0000000000000000 9000000100054000 9000000100053000 9000000000ebb70c 9000000100004c00 9000000004000001 90000001002fb7e4 bae765461f31cb12 0000000000000000 0000000000000000 0000000000000006 90000000027af000 0000000000000030 90000000027af000 900000087cd6f800 9000000100053000 0000000000000000 9000000000ebc560 7a2500147cdaf720 bae765461f31cb12 0000000000000001 0000000000000030 ... Call Trace: [<90000000017e5534>] loongson_gpu_fixup_dma_hang+0xb4/0x210 [<9000000000eebc08>] pci_fixup_device+0x108/0x280 [<9000000000ebb70c>] pci_setup_device+0x24c/0x690 [<9000000000ebc560>] pci_scan_single_device+0xe0/0x140 [<9000000000ebc684>] pci_scan_slot+0xc4/0x280 [<9000000000ebdd00>] pci_scan_child_bus_extend+0x60/0x3f0 [<9000000000f5bc94>] acpi_pci_root_create+0x2b4/0x420 [<90000000017e5e74>] pci_acpi_scan_root+0x2d4/0x440 [<9000000000f5b02c>] acpi_pci_root_add+0x21c/0x3a0 [<9000000000f4ee54>] acpi_bus_attach+0x1a4/0x3c0 [<90000000010e200c>] device_for_each_child+0x6c/0xe0 [<9000000000f4bbf4>] acpi_dev_for_each_child+0x44/0x70 [<9000000000f4ef40>] acpi_bus_attach+0x290/0x3c0 [<90000000010e200c>] device_for_each_child+0x6c/0xe0 [<9000000000f4bbf4>] acpi_dev_for_each_child+0x44/0x70 [<9000000000f4ef40>] acpi_bus_attach+0x290/0x3c0 [<9000000000f5211c>] acpi_bus_scan+0x6c/0x280 [<900000000189c028>] acpi_scan_init+0x194/0x310 [<900000000189bc6c>] acpi_init+0xcc/0x140 [<9000000000220cdc>] do_one_initcall+0x4c/0x310 [<90000000018618fc>] kernel_init_freeable+0x258/0x2d4 [<900000000184326c>] kernel_init+0x28/0x13c [<9000000000222008>] ret_from_kernel_thread+0xc/0xa4

In the Linux kernel, the following vulnerability has been resolved: irqchip/gic-v3-its: Don't enable interrupts in its_irq_set_vcpu_affinity() The following call-chain leads to enabling interrupts in a nested interrupt disabled section: irq_set_vcpu_affinity() irq_get_desc_lock() raw_spin_lock_irqsave() <--- Disable interrupts its_irq_set_vcpu_affinity() guard(raw_spinlock_irq) <--- Enables interrupts when leaving the guard() irq_put_desc_unlock() <--- Warns because interrupts are enabled This was broken in commit b97e8a2f7130, which replaced the original raw_spin_[un]lock() pair with guard(raw_spinlock_irq). Fix the issue by using guard(raw_spinlock). [ tglx: Massaged change log ]

In the Linux kernel, the following vulnerability has been resolved: nfs_common: must not hold RCU while calling nfsd_file_put_local Move holding the RCU from nfs_to_nfsd_file_put_local to nfs_to_nfsd_net_put. It is the call to nfs_to->nfsd_serv_put that requires the RCU anyway (the puts for nfsd_file and netns were combined to avoid an extra indirect reference but that micro-optimization isn't possible now). This fixes xfstests generic/013 and it triggering: "Voluntary context switch within RCU read-side critical section!" [ 143.545738] Call Trace: [ 143.546206] <TASK> [ 143.546625] ? show_regs+0x6d/0x80 [ 143.547267] ? __warn+0x91/0x140 [ 143.547951] ? rcu_note_context_switch+0x496/0x5d0 [ 143.548856] ? report_bug+0x193/0x1a0 [ 143.549557] ? handle_bug+0x63/0xa0 [ 143.550214] ? exc_invalid_op+0x1d/0x80 [ 143.550938] ? asm_exc_invalid_op+0x1f/0x30 [ 143.551736] ? rcu_note_context_switch+0x496/0x5d0 [ 143.552634] ? wakeup_preempt+0x62/0x70 [ 143.553358] __schedule+0xaa/0x1380 [ 143.554025] ? _raw_spin_unlock_irqrestore+0x12/0x40 [ 143.554958] ? try_to_wake_up+0x1fe/0x6b0 [ 143.555715] ? wake_up_process+0x19/0x20 [ 143.556452] schedule+0x2e/0x120 [ 143.557066] schedule_preempt_disabled+0x19/0x30 [ 143.557933] rwsem_down_read_slowpath+0x24d/0x4a0 [ 143.558818] ? xfs_efi_item_format+0x50/0xc0 [xfs] [ 143.559894] down_read+0x4e/0xb0 [ 143.560519] xlog_cil_commit+0x1b2/0xbc0 [xfs] [ 143.561460] ? _raw_spin_unlock+0x12/0x30 [ 143.562212] ? xfs_inode_item_precommit+0xc7/0x220 [xfs] [ 143.563309] ? xfs_trans_run_precommits+0x69/0xd0 [xfs] [ 143.564394] __xfs_trans_commit+0xb5/0x330 [xfs] [ 143.565367] xfs_trans_roll+0x48/0xc0 [xfs] [ 143.566262] xfs_defer_trans_roll+0x57/0x100 [xfs] [ 143.567278] xfs_defer_finish_noroll+0x27a/0x490 [xfs] [ 143.568342] xfs_defer_finish+0x1a/0x80 [xfs] [ 143.569267] xfs_bunmapi_range+0x4d/0xb0 [xfs] [ 143.570208] xfs_itruncate_extents_flags+0x13d/0x230 [xfs] [ 143.571353] xfs_free_eofblocks+0x12e/0x190 [xfs] [ 143.572359] xfs_file_release+0x12d/0x140 [xfs] [ 143.573324] __fput+0xe8/0x2d0 [ 143.573922] __fput_sync+0x1d/0x30 [ 143.574574] nfsd_filp_close+0x33/0x60 [nfsd] [ 143.575430] nfsd_file_free+0x96/0x150 [nfsd] [ 143.576274] nfsd_file_put+0xf7/0x1a0 [nfsd] [ 143.577104] nfsd_file_put_local+0x18/0x30 [nfsd] [ 143.578070] nfs_close_local_fh+0x101/0x110 [nfs_localio] [ 143.579079] __put_nfs_open_context+0xc9/0x180 [nfs] [ 143.580031] nfs_file_clear_open_context+0x4a/0x60 [nfs] [ 143.581038] nfs_file_release+0x3e/0x60 [nfs] [ 143.581879] __fput+0xe8/0x2d0 [ 143.582464] __fput_sync+0x1d/0x30 [ 143.583108] __x64_sys_close+0x41/0x80 [ 143.583823] x64_sys_call+0x189a/0x20d0 [ 143.584552] do_syscall_64+0x64/0x170 [ 143.585240] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 143.586185] RIP: 0033:0x7f3c5153efd7

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix deadlock when freeing cgroup storage The following commit bc235cdb423a ("bpf: Prevent deadlock from recursive bpf_task_storage_[get|delete]") first introduced deadlock prevention for fentry/fexit programs attaching on bpf_task_storage helpers. That commit also employed the logic in map free path in its v6 version. Later bpf_cgrp_storage was first introduced in c4bcfb38a95e ("bpf: Implement cgroup storage available to non-cgroup-attached bpf progs") which faces the same issue as bpf_task_storage, instead of its busy counter, NULL was passed to bpf_local_storage_map_free() which opened a window to cause deadlock: <TASK> (acquiring local_storage->lock) _raw_spin_lock_irqsave+0x3d/0x50 bpf_local_storage_update+0xd1/0x460 bpf_cgrp_storage_get+0x109/0x130 bpf_prog_a4d4a370ba857314_cgrp_ptr+0x139/0x170 ? __bpf_prog_enter_recur+0x16/0x80 bpf_trampoline_6442485186+0x43/0xa4 cgroup_storage_ptr+0x9/0x20 (holding local_storage->lock) bpf_selem_unlink_storage_nolock.constprop.0+0x135/0x160 bpf_selem_unlink_storage+0x6f/0x110 bpf_local_storage_map_free+0xa2/0x110 bpf_map_free_deferred+0x5b/0x90 process_one_work+0x17c/0x390 worker_thread+0x251/0x360 kthread+0xd2/0x100 ret_from_fork+0x34/0x50 ret_from_fork_asm+0x1a/0x30 </TASK> Progs: - A: SEC("fentry/cgroup_storage_ptr") - cgid (BPF_MAP_TYPE_HASH) Record the id of the cgroup the current task belonging to in this hash map, using the address of the cgroup as the map key. - cgrpa (BPF_MAP_TYPE_CGRP_STORAGE) If current task is a kworker, lookup the above hash map using function parameter @owner as the key to get its corresponding cgroup id which is then used to get a trusted pointer to the cgroup through bpf_cgroup_from_id(). This trusted pointer can then be passed to bpf_cgrp_storage_get() to finally trigger the deadlock issue. - B: SEC("tp_btf/sys_enter") - cgrpb (BPF_MAP_TYPE_CGRP_STORAGE) The only purpose of this prog is to fill Prog A's hash map by calling bpf_cgrp_storage_get() for as many userspace tasks as possible. Steps to reproduce: - Run A; - while (true) { Run B; Destroy B; } Fix this issue by passing its busy counter to the free procedure so it can be properly incremented before storage/smap locking.

In the Linux kernel, the following vulnerability has been resolved: team: prevent adding a device which is already a team device lower Prevent adding a device which is already a team device lower, e.g. adding veth0 if vlan1 was already added and veth0 is a lower of vlan1. This is not useful in practice and can lead to recursive locking: $ ip link add veth0 type veth peer name veth1 $ ip link set veth0 up $ ip link set veth1 up $ ip link add link veth0 name veth0.1 type vlan protocol 802.1Q id 1 $ ip link add team0 type team $ ip link set veth0.1 down $ ip link set veth0.1 master team0 team0: Port device veth0.1 added $ ip link set veth0 down $ ip link set veth0 master team0 ============================================ WARNING: possible recursive locking detected 6.13.0-rc2-virtme-00441-ga14a429069bb #46 Not tainted -------------------------------------------- ip/7684 is trying to acquire lock: ffff888016848e00 (team->team_lock_key){+.+.}-{4:4}, at: team_device_event (drivers/net/team/team_core.c:2928 drivers/net/team/team_core.c:2951 drivers/net/team/team_core.c:2973) but task is already holding lock: ffff888016848e00 (team->team_lock_key){+.+.}-{4:4}, at: team_add_slave (drivers/net/team/team_core.c:1147 drivers/net/team/team_core.c:1977) other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(team->team_lock_key); lock(team->team_lock_key); *** DEADLOCK *** May be due to missing lock nesting notation 2 locks held by ip/7684: stack backtrace: CPU: 3 UID: 0 PID: 7684 Comm: ip Not tainted 6.13.0-rc2-virtme-00441-ga14a429069bb #46 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 Call Trace: <TASK> dump_stack_lvl (lib/dump_stack.c:122) print_deadlock_bug.cold (kernel/locking/lockdep.c:3040) __lock_acquire (kernel/locking/lockdep.c:3893 kernel/locking/lockdep.c:5226) ? netlink_broadcast_filtered (net/netlink/af_netlink.c:1548) lock_acquire.part.0 (kernel/locking/lockdep.c:467 kernel/locking/lockdep.c:5851) ? team_device_event (drivers/net/team/team_core.c:2928 drivers/net/team/team_core.c:2951 drivers/net/team/team_core.c:2973) ? trace_lock_acquire (./include/trace/events/lock.h:24 (discriminator 2)) ? team_device_event (drivers/net/team/team_core.c:2928 drivers/net/team/team_core.c:2951 drivers/net/team/team_core.c:2973) ? lock_acquire (kernel/locking/lockdep.c:5822) ? team_device_event (drivers/net/team/team_core.c:2928 drivers/net/team/team_core.c:2951 drivers/net/team/team_core.c:2973) __mutex_lock (kernel/locking/mutex.c:587 kernel/locking/mutex.c:735) ? team_device_event (drivers/net/team/team_core.c:2928 drivers/net/team/team_core.c:2951 drivers/net/team/team_core.c:2973) ? team_device_event (drivers/net/team/team_core.c:2928 drivers/net/team/team_core.c:2951 drivers/net/team/team_core.c:2973) ? fib_sync_up (net/ipv4/fib_semantics.c:2167) ? team_device_event (drivers/net/team/team_core.c:2928 drivers/net/team/team_core.c:2951 drivers/net/team/team_core.c:2973) team_device_event (drivers/net/team/team_core.c:2928 drivers/net/team/team_core.c:2951 drivers/net/team/team_core.c:2973) notifier_call_chain (kernel/notifier.c:85) call_netdevice_notifiers_info (net/core/dev.c:1996) __dev_notify_flags (net/core/dev.c:8993) ? __dev_change_flags (net/core/dev.c:8975) dev_change_flags (net/core/dev.c:9027) vlan_device_event (net/8021q/vlan.c:85 net/8021q/vlan.c:470) ? br_device_event (net/bridge/br.c:143) notifier_call_chain (kernel/notifier.c:85) call_netdevice_notifiers_info (net/core/dev.c:1996) dev_open (net/core/dev.c:1519 net/core/dev.c:1505) team_add_slave (drivers/net/team/team_core.c:1219 drivers/net/team/team_core.c:1977) ? __pfx_team_add_slave (drivers/net/team/team_core.c:1972) do_set_master (net/core/rtnetlink.c:2917) do_setlink.isra.0 (net/core/rtnetlink.c:3117)

In the Linux kernel, the following vulnerability has been resolved: ALSA: caiaq: Use snd_card_free_when_closed() at disconnection The USB disconnect callback is supposed to be short and not too-long waiting. OTOH, the current code uses snd_card_free() at disconnection, but this waits for the close of all used fds, hence it can take long. It eventually blocks the upper layer USB ioctls, which may trigger a soft lockup. An easy workaround is to replace snd_card_free() with snd_card_free_when_closed(). This variant returns immediately while the release of resources is done asynchronously by the card device release at the last close. This patch also splits the code to the disconnect and the free phases; the former is called immediately at the USB disconnect callback while the latter is called from the card destructor.

In the Linux kernel, the following vulnerability has been resolved: mm/vmalloc: combine all TLB flush operations of KASAN shadow virtual address into one operation When compiling kernel source 'make -j $(nproc)' with the up-and-running KASAN-enabled kernel on a 256-core machine, the following soft lockup is shown: watchdog: BUG: soft lockup - CPU#28 stuck for 22s! [kworker/28:1:1760] CPU: 28 PID: 1760 Comm: kworker/28:1 Kdump: loaded Not tainted 6.10.0-rc5 #95 Workqueue: events drain_vmap_area_work RIP: 0010:smp_call_function_many_cond+0x1d8/0xbb0 Code: 38 c8 7c 08 84 c9 0f 85 49 08 00 00 8b 45 08 a8 01 74 2e 48 89 f1 49 89 f7 48 c1 e9 03 41 83 e7 07 4c 01 e9 41 83 c7 03 f3 90 <0f> b6 01 41 38 c7 7c 08 84 c0 0f 85 d4 06 00 00 8b 45 08 a8 01 75 RSP: 0018:ffffc9000cb3fb60 EFLAGS: 00000202 RAX: 0000000000000011 RBX: ffff8883bc4469c0 RCX: ffffed10776e9949 RDX: 0000000000000002 RSI: ffff8883bb74ca48 RDI: ffffffff8434dc50 RBP: ffff8883bb74ca40 R08: ffff888103585dc0 R09: ffff8884533a1800 R10: 0000000000000004 R11: ffffffffffffffff R12: ffffed1077888d39 R13: dffffc0000000000 R14: ffffed1077888d38 R15: 0000000000000003 FS: 0000000000000000(0000) GS:ffff8883bc400000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00005577b5c8d158 CR3: 0000000004850000 CR4: 0000000000350ef0 Call Trace: <IRQ> ? watchdog_timer_fn+0x2cd/0x390 ? __pfx_watchdog_timer_fn+0x10/0x10 ? __hrtimer_run_queues+0x300/0x6d0 ? sched_clock_cpu+0x69/0x4e0 ? __pfx___hrtimer_run_queues+0x10/0x10 ? srso_return_thunk+0x5/0x5f ? ktime_get_update_offsets_now+0x7f/0x2a0 ? srso_return_thunk+0x5/0x5f ? srso_return_thunk+0x5/0x5f ? hrtimer_interrupt+0x2ca/0x760 ? __sysvec_apic_timer_interrupt+0x8c/0x2b0 ? sysvec_apic_timer_interrupt+0x6a/0x90 </IRQ> <TASK> ? asm_sysvec_apic_timer_interrupt+0x16/0x20 ? smp_call_function_many_cond+0x1d8/0xbb0 ? __pfx_do_kernel_range_flush+0x10/0x10 on_each_cpu_cond_mask+0x20/0x40 flush_tlb_kernel_range+0x19b/0x250 ? srso_return_thunk+0x5/0x5f ? kasan_release_vmalloc+0xa7/0xc0 purge_vmap_node+0x357/0x820 ? __pfx_purge_vmap_node+0x10/0x10 __purge_vmap_area_lazy+0x5b8/0xa10 drain_vmap_area_work+0x21/0x30 process_one_work+0x661/0x10b0 worker_thread+0x844/0x10e0 ? srso_return_thunk+0x5/0x5f ? __kthread_parkme+0x82/0x140 ? __pfx_worker_thread+0x10/0x10 kthread+0x2a5/0x370 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x30/0x70 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> Debugging Analysis: 1. The following ftrace log shows that the lockup CPU spends too much time iterating vmap_nodes and flushing TLB when purging vm_area structures. (Some info is trimmed). kworker: funcgraph_entry: | drain_vmap_area_work() { kworker: funcgraph_entry: | mutex_lock() { kworker: funcgraph_entry: 1.092 us | __cond_resched(); kworker: funcgraph_exit: 3.306 us | } ... ... kworker: funcgraph_entry: | flush_tlb_kernel_range() { ... ... kworker: funcgraph_exit: # 7533.649 us | } ... ... kworker: funcgraph_entry: 2.344 us | mutex_unlock(); kworker: funcgraph_exit: $ 23871554 us | } The drain_vmap_area_work() spends over 23 seconds. There are 2805 flush_tlb_kernel_range() calls in the ftrace log. * One is called in __purge_vmap_area_lazy(). * Others are called by purge_vmap_node->kasan_release_vmalloc. purge_vmap_node() iteratively releases kasan vmalloc allocations and flushes TLB for each vmap_area. - [Rough calculation] Each flush_tlb_kernel_range() runs about 7.5ms. -- 2804 * 7.5ms = 21.03 seconds. -- That's why a soft lock is triggered. 2. Extending the soft lockup time can work around the issue (For example, # echo ---truncated---

In the Linux kernel, the following vulnerability has been resolved: net: bridge: fix soft lockup in br_multicast_query_expired() When set multicast_query_interval to a large value, the local variable 'time' in br_multicast_send_query() may overflow. If the time is smaller than jiffies, the timer will expire immediately, and then call mod_timer() again, which creates a loop and may trigger the following soft lockup issue. watchdog: BUG: soft lockup - CPU#1 stuck for 221s! [rb_consumer:66] CPU: 1 UID: 0 PID: 66 Comm: rb_consumer Not tainted 6.16.0+ #259 PREEMPT(none) Call Trace: <IRQ> __netdev_alloc_skb+0x2e/0x3a0 br_ip6_multicast_alloc_query+0x212/0x1b70 __br_multicast_send_query+0x376/0xac0 br_multicast_send_query+0x299/0x510 br_multicast_query_expired.constprop.0+0x16d/0x1b0 call_timer_fn+0x3b/0x2a0 __run_timers+0x619/0x950 run_timer_softirq+0x11c/0x220 handle_softirqs+0x18e/0x560 __irq_exit_rcu+0x158/0x1a0 sysvec_apic_timer_interrupt+0x76/0x90 </IRQ> This issue can be reproduced with: ip link add br0 type bridge echo 1 > /sys/class/net/br0/bridge/multicast_querier echo 0xffffffffffffffff > /sys/class/net/br0/bridge/multicast_query_interval ip link set dev br0 up The multicast_startup_query_interval can also cause this issue. Similar to the commit 99b40610956a ("net: bridge: mcast: add and enforce query interval minimum"), add check for the query interval maximum to fix this issue.

In the Linux kernel, the following vulnerability has been resolved: md/raid10: fix deadlock with check operation and nowait requests When an array check is running it will raise the barrier at which point normal requests will become blocked and increment the nr_pending value to signal there is work pending inside of wait_barrier(). NOWAIT requests do not block and so will return immediately with an error, and additionally do not increment nr_pending in wait_barrier(). Upstream change commit 43806c3d5b9b ("raid10: cleanup memleak at raid10_make_request") added a call to raid_end_bio_io() to fix a memory leak when NOWAIT requests hit this condition. raid_end_bio_io() eventually calls allow_barrier() and it will unconditionally do an atomic_dec_and_test(&conf->nr_pending) even though the corresponding increment on nr_pending didn't happen in the NOWAIT case. This can be easily seen by starting a check operation while an application is doing nowait IO on the same array. This results in a deadlocked state due to nr_pending value underflowing and so the md resync thread gets stuck waiting for nr_pending to == 0. Output of r10conf state of the array when we hit this condition: crash> struct r10conf barrier = 1, nr_pending = { counter = -41 }, nr_waiting = 15, nr_queued = 0, Example of md_sync thread stuck waiting on raise_barrier() and other requests stuck in wait_barrier(): md1_resync [<0>] raise_barrier+0xce/0x1c0 [<0>] raid10_sync_request+0x1ca/0x1ed0 [<0>] md_do_sync+0x779/0x1110 [<0>] md_thread+0x90/0x160 [<0>] kthread+0xbe/0xf0 [<0>] ret_from_fork+0x34/0x50 [<0>] ret_from_fork_asm+0x1a/0x30 kworker/u1040:2+flush-253:4 [<0>] wait_barrier+0x1de/0x220 [<0>] regular_request_wait+0x30/0x180 [<0>] raid10_make_request+0x261/0x1000 [<0>] md_handle_request+0x13b/0x230 [<0>] __submit_bio+0x107/0x1f0 [<0>] submit_bio_noacct_nocheck+0x16f/0x390 [<0>] ext4_io_submit+0x24/0x40 [<0>] ext4_do_writepages+0x254/0xc80 [<0>] ext4_writepages+0x84/0x120 [<0>] do_writepages+0x7a/0x260 [<0>] __writeback_single_inode+0x3d/0x300 [<0>] writeback_sb_inodes+0x1dd/0x470 [<0>] __writeback_inodes_wb+0x4c/0xe0 [<0>] wb_writeback+0x18b/0x2d0 [<0>] wb_workfn+0x2a1/0x400 [<0>] process_one_work+0x149/0x330 [<0>] worker_thread+0x2d2/0x410 [<0>] kthread+0xbe/0xf0 [<0>] ret_from_fork+0x34/0x50 [<0>] ret_from_fork_asm+0x1a/0x30