In the Linux kernel, the following vulnerability has been resolved: net: wan: fsl_qmc_hdlc: Convert carrier_lock spinlock to a mutex The carrier_lock spinlock protects the carrier detection. While it is held, framer_get_status() is called which in turn takes a mutex. This is not correct and can lead to a deadlock. A run with PROVE_LOCKING enabled detected the issue: [ BUG: Invalid wait context ] ... c204ddbc (&framer->mutex){+.+.}-{3:3}, at: framer_get_status+0x40/0x78 other info that might help us debug this: context-{4:4} 2 locks held by ifconfig/146: #0: c0926a38 (rtnl_mutex){+.+.}-{3:3}, at: devinet_ioctl+0x12c/0x664 #1: c2006a40 (&qmc_hdlc->carrier_lock){....}-{2:2}, at: qmc_hdlc_framer_set_carrier+0x30/0x98 Avoid the spinlock usage and convert carrier_lock to a mutex.

In the Linux kernel, the following vulnerability has been resolved: mptcp: init: protect sched with rcu_read_lock Enabling CONFIG_PROVE_RCU_LIST with its dependence CONFIG_RCU_EXPERT creates this splat when an MPTCP socket is created: ============================= WARNING: suspicious RCU usage 6.12.0-rc2+ #11 Not tainted ----------------------------- net/mptcp/sched.c:44 RCU-list traversed in non-reader section!! other info that might help us debug this: rcu_scheduler_active = 2, debug_locks = 1 no locks held by mptcp_connect/176. stack backtrace: CPU: 0 UID: 0 PID: 176 Comm: mptcp_connect Not tainted 6.12.0-rc2+ #11 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 Call Trace: <TASK> dump_stack_lvl (lib/dump_stack.c:123) lockdep_rcu_suspicious (kernel/locking/lockdep.c:6822) mptcp_sched_find (net/mptcp/sched.c:44 (discriminator 7)) mptcp_init_sock (net/mptcp/protocol.c:2867 (discriminator 1)) ? sock_init_data_uid (arch/x86/include/asm/atomic.h:28) inet_create.part.0.constprop.0 (net/ipv4/af_inet.c:386) ? __sock_create (include/linux/rcupdate.h:347 (discriminator 1)) __sock_create (net/socket.c:1576) __sys_socket (net/socket.c:1671) ? __pfx___sys_socket (net/socket.c:1712) ? do_user_addr_fault (arch/x86/mm/fault.c:1419 (discriminator 1)) __x64_sys_socket (net/socket.c:1728) do_syscall_64 (arch/x86/entry/common.c:52 (discriminator 1)) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130) That's because when the socket is initialised, rcu_read_lock() is not used despite the explicit comment written above the declaration of mptcp_sched_find() in sched.c. Adding the missing lock/unlock avoids the warning.

In the Linux kernel, the following vulnerability has been resolved: drm/vmwgfx: Fix a deadlock in dma buf fence polling Introduce a version of the fence ops that on release doesn't remove the fence from the pending list, and thus doesn't require a lock to fix poll->fence wait->fence unref deadlocks. vmwgfx overwrites the wait callback to iterate over the list of all fences and update their status, to do that it holds a lock to prevent the list modifcations from other threads. The fence destroy callback both deletes the fence and removes it from the list of pending fences, for which it holds a lock. dma buf polling cb unrefs a fence after it's been signaled: so the poll calls the wait, which signals the fences, which are being destroyed. The destruction tries to acquire the lock on the pending fences list which it can never get because it's held by the wait from which it was called. Old bug, but not a lot of userspace apps were using dma-buf polling interfaces. Fix those, in particular this fixes KDE stalls/deadlock.

In the Linux kernel, the following vulnerability has been resolved: cachefiles: add missing lock protection when polling Add missing lock protection in poll routine when iterating xarray, otherwise: Even with RCU read lock held, only the slot of the radix tree is ensured to be pinned there, while the data structure (e.g. struct cachefiles_req) stored in the slot has no such guarantee. The poll routine will iterate the radix tree and dereference cachefiles_req accordingly. Thus RCU read lock is not adequate in this case and spinlock is needed here.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: MGMT: Fix possible deadlocks This fixes possible deadlocks like the following caused by hci_cmd_sync_dequeue causing the destroy function to run: INFO: task kworker/u19:0:143 blocked for more than 120 seconds. Tainted: G W O 6.8.0-2024-03-19-intel-next-iLS-24ww14 #1 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. task:kworker/u19:0 state:D stack:0 pid:143 tgid:143 ppid:2 flags:0x00004000 Workqueue: hci0 hci_cmd_sync_work [bluetooth] Call Trace: <TASK> __schedule+0x374/0xaf0 schedule+0x3c/0xf0 schedule_preempt_disabled+0x1c/0x30 __mutex_lock.constprop.0+0x3ef/0x7a0 __mutex_lock_slowpath+0x13/0x20 mutex_lock+0x3c/0x50 mgmt_set_connectable_complete+0xa4/0x150 [bluetooth] ? kfree+0x211/0x2a0 hci_cmd_sync_dequeue+0xae/0x130 [bluetooth] ? __pfx_cmd_complete_rsp+0x10/0x10 [bluetooth] cmd_complete_rsp+0x26/0x80 [bluetooth] mgmt_pending_foreach+0x4d/0x70 [bluetooth] __mgmt_power_off+0x8d/0x180 [bluetooth] ? _raw_spin_unlock_irq+0x23/0x40 hci_dev_close_sync+0x445/0x5b0 [bluetooth] hci_set_powered_sync+0x149/0x250 [bluetooth] set_powered_sync+0x24/0x60 [bluetooth] hci_cmd_sync_work+0x90/0x150 [bluetooth] process_one_work+0x13e/0x300 worker_thread+0x2f7/0x420 ? __pfx_worker_thread+0x10/0x10 kthread+0x107/0x140 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x3d/0x60 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1b/0x30 </TASK>

In the Linux kernel, the following vulnerability has been resolved: exfat: fix potential deadlock on __exfat_get_dentry_set When accessing a file with more entries than ES_MAX_ENTRY_NUM, the bh-array is allocated in __exfat_get_entry_set. The problem is that the bh-array is allocated with GFP_KERNEL. It does not make sense. In the following cases, a deadlock for sbi->s_lock between the two processes may occur. CPU0 CPU1 ---- ---- kswapd balance_pgdat lock(fs_reclaim) exfat_iterate lock(&sbi->s_lock) exfat_readdir exfat_get_uniname_from_ext_entry exfat_get_dentry_set __exfat_get_dentry_set kmalloc_array ... lock(fs_reclaim) ... evict exfat_evict_inode lock(&sbi->s_lock) To fix this, let's allocate bh-array with GFP_NOFS.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Fix missing lock on sync reset reload On sync reset reload work, when remote host updates devlink on reload actions performed on that host, it misses taking devlink lock before calling devlink_remote_reload_actions_performed() which results in triggering lock assert like the following: WARNING: CPU: 4 PID: 1164 at net/devlink/core.c:261 devl_assert_locked+0x3e/0x50 … CPU: 4 PID: 1164 Comm: kworker/u96:6 Tainted: G S W 6.10.0-rc2+ #116 Hardware name: Supermicro SYS-2028TP-DECTR/X10DRT-PT, BIOS 2.0 12/18/2015 Workqueue: mlx5_fw_reset_events mlx5_sync_reset_reload_work [mlx5_core] RIP: 0010:devl_assert_locked+0x3e/0x50 … Call Trace: <TASK> ? __warn+0xa4/0x210 ? devl_assert_locked+0x3e/0x50 ? report_bug+0x160/0x280 ? handle_bug+0x3f/0x80 ? exc_invalid_op+0x17/0x40 ? asm_exc_invalid_op+0x1a/0x20 ? devl_assert_locked+0x3e/0x50 devlink_notify+0x88/0x2b0 ? mlx5_attach_device+0x20c/0x230 [mlx5_core] ? __pfx_devlink_notify+0x10/0x10 ? process_one_work+0x4b6/0xbb0 process_one_work+0x4b6/0xbb0 […]

In the Linux kernel, the following vulnerability has been resolved: i3c: Use i3cdev->desc->info instead of calling i3c_device_get_info() to avoid deadlock A deadlock may happen since the i3c_master_register() acquires &i3cbus->lock twice. See the log below. Use i3cdev->desc->info instead of calling i3c_device_info() to avoid acquiring the lock twice. v2: - Modified the title and commit message ============================================ WARNING: possible recursive locking detected 6.11.0-mainline -------------------------------------------- init/1 is trying to acquire lock: f1ffff80a6a40dc0 (&i3cbus->lock){++++}-{3:3}, at: i3c_bus_normaluse_lock but task is already holding lock: f1ffff80a6a40dc0 (&i3cbus->lock){++++}-{3:3}, at: i3c_master_register other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&i3cbus->lock); lock(&i3cbus->lock); *** DEADLOCK *** May be due to missing lock nesting notation 2 locks held by init/1: #0: fcffff809b6798f8 (&dev->mutex){....}-{3:3}, at: __driver_attach #1: f1ffff80a6a40dc0 (&i3cbus->lock){++++}-{3:3}, at: i3c_master_register stack backtrace: CPU: 6 UID: 0 PID: 1 Comm: init Call trace: dump_backtrace+0xfc/0x17c show_stack+0x18/0x28 dump_stack_lvl+0x40/0xc0 dump_stack+0x18/0x24 print_deadlock_bug+0x388/0x390 __lock_acquire+0x18bc/0x32ec lock_acquire+0x134/0x2b0 down_read+0x50/0x19c i3c_bus_normaluse_lock+0x14/0x24 i3c_device_get_info+0x24/0x58 i3c_device_uevent+0x34/0xa4 dev_uevent+0x310/0x384 kobject_uevent_env+0x244/0x414 kobject_uevent+0x14/0x20 device_add+0x278/0x460 device_register+0x20/0x34 i3c_master_register_new_i3c_devs+0x78/0x154 i3c_master_register+0x6a0/0x6d4 mtk_i3c_master_probe+0x3b8/0x4d8 platform_probe+0xa0/0xe0 really_probe+0x114/0x454 __driver_probe_device+0xa0/0x15c driver_probe_device+0x3c/0x1ac __driver_attach+0xc4/0x1f0 bus_for_each_dev+0x104/0x160 driver_attach+0x24/0x34 bus_add_driver+0x14c/0x294 driver_register+0x68/0x104 __platform_driver_register+0x20/0x30 init_module+0x20/0xfe4 do_one_initcall+0x184/0x464 do_init_module+0x58/0x1ec load_module+0xefc/0x10c8 __arm64_sys_finit_module+0x238/0x33c invoke_syscall+0x58/0x10c el0_svc_common+0xa8/0xdc do_el0_svc+0x1c/0x28 el0_svc+0x50/0xac el0t_64_sync_handler+0x70/0xbc el0t_64_sync+0x1a8/0x1ac

In the Linux kernel, the following vulnerability has been resolved: Revert "sched/fair: Make sure to try to detach at least one movable task" This reverts commit b0defa7ae03ecf91b8bfd10ede430cff12fcbd06. b0defa7ae03ec changed the load balancing logic to ignore env.max_loop if all tasks examined to that point were pinned. The goal of the patch was to make it more likely to be able to detach a task buried in a long list of pinned tasks. However, this has the unfortunate side effect of creating an O(n) iteration in detach_tasks(), as we now must fully iterate every task on a cpu if all or most are pinned. Since this load balance code is done with rq lock held, and often in softirq context, it is very easy to trigger hard lockups. We observed such hard lockups with a user who affined O(10k) threads to a single cpu. When I discussed this with Vincent he initially suggested that we keep the limit on the number of tasks to detach, but increase the number of tasks we can search. However, after some back and forth on the mailing list, he recommended we instead revert the original patch, as it seems likely no one was actually getting hit by the original issue.

In the Linux kernel, the following vulnerability has been resolved: bpf: Fail bpf_timer_cancel when callback is being cancelled Given a schedule: timer1 cb timer2 cb bpf_timer_cancel(timer2); bpf_timer_cancel(timer1); Both bpf_timer_cancel calls would wait for the other callback to finish executing, introducing a lockup. Add an atomic_t count named 'cancelling' in bpf_hrtimer. This keeps track of all in-flight cancellation requests for a given BPF timer. Whenever cancelling a BPF timer, we must check if we have outstanding cancellation requests, and if so, we must fail the operation with an error (-EDEADLK) since cancellation is synchronous and waits for the callback to finish executing. This implies that we can enter a deadlock situation involving two or more timer callbacks executing in parallel and attempting to cancel one another. Note that we avoid incrementing the cancelling counter for the target timer (the one being cancelled) if bpf_timer_cancel is not invoked from a callback, to avoid spurious errors. The whole point of detecting cur->cancelling and returning -EDEADLK is to not enter a busy wait loop (which may or may not lead to a lockup). This does not apply in case the caller is in a non-callback context, the other side can continue to cancel as it sees fit without running into errors. Background on prior attempts: Earlier versions of this patch used a bool 'cancelling' bit and used the following pattern under timer->lock to publish cancellation status. lock(t->lock); t->cancelling = true; mb(); if (cur->cancelling) return -EDEADLK; unlock(t->lock); hrtimer_cancel(t->timer); t->cancelling = false; The store outside the critical section could overwrite a parallel requests t->cancelling assignment to true, to ensure the parallely executing callback observes its cancellation status. It would be necessary to clear this cancelling bit once hrtimer_cancel is done, but lack of serialization introduced races. Another option was explored where bpf_timer_start would clear the bit when (re)starting the timer under timer->lock. This would ensure serialized access to the cancelling bit, but may allow it to be cleared before in-flight hrtimer_cancel has finished executing, such that lockups can occur again. Thus, we choose an atomic counter to keep track of all outstanding cancellation requests and use it to prevent lockups in case callbacks attempt to cancel each other while executing in parallel.

In the Linux kernel, the following vulnerability has been resolved: riscv: rewrite __kernel_map_pages() to fix sleeping in invalid context __kernel_map_pages() is a debug function which clears the valid bit in page table entry for deallocated pages to detect illegal memory accesses to freed pages. This function set/clear the valid bit using __set_memory(). __set_memory() acquires init_mm's semaphore, and this operation may sleep. This is problematic, because __kernel_map_pages() can be called in atomic context, and thus is illegal to sleep. An example warning that this causes: BUG: sleeping function called from invalid context at kernel/locking/rwsem.c:1578 in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 2, name: kthreadd preempt_count: 2, expected: 0 CPU: 0 PID: 2 Comm: kthreadd Not tainted 6.9.0-g1d4c6d784ef6 #37 Hardware name: riscv-virtio,qemu (DT) Call Trace: [<ffffffff800060dc>] dump_backtrace+0x1c/0x24 [<ffffffff8091ef6e>] show_stack+0x2c/0x38 [<ffffffff8092baf8>] dump_stack_lvl+0x5a/0x72 [<ffffffff8092bb24>] dump_stack+0x14/0x1c [<ffffffff8003b7ac>] __might_resched+0x104/0x10e [<ffffffff8003b7f4>] __might_sleep+0x3e/0x62 [<ffffffff8093276a>] down_write+0x20/0x72 [<ffffffff8000cf00>] __set_memory+0x82/0x2fa [<ffffffff8000d324>] __kernel_map_pages+0x5a/0xd4 [<ffffffff80196cca>] __alloc_pages_bulk+0x3b2/0x43a [<ffffffff8018ee82>] __vmalloc_node_range+0x196/0x6ba [<ffffffff80011904>] copy_process+0x72c/0x17ec [<ffffffff80012ab4>] kernel_clone+0x60/0x2fe [<ffffffff80012f62>] kernel_thread+0x82/0xa0 [<ffffffff8003552c>] kthreadd+0x14a/0x1be [<ffffffff809357de>] ret_from_fork+0xe/0x1c Rewrite this function with apply_to_existing_page_range(). It is fine to not have any locking, because __kernel_map_pages() works with pages being allocated/deallocated and those pages are not changed by anyone else in the meantime.

In the Linux kernel, the following vulnerability has been resolved: usb: dwc3: core: remove lock of otg mode during gadget suspend/resume to avoid deadlock When config CONFIG_USB_DWC3_DUAL_ROLE is selected, and trigger system to enter suspend status with below command: echo mem > /sys/power/state There will be a deadlock issue occurring. Detailed invoking path as below: dwc3_suspend_common() spin_lock_irqsave(&dwc->lock, flags); <-- 1st dwc3_gadget_suspend(dwc); dwc3_gadget_soft_disconnect(dwc); spin_lock_irqsave(&dwc->lock, flags); <-- 2nd This issue is exposed by commit c7ebd8149ee5 ("usb: dwc3: gadget: Fix NULL pointer dereference in dwc3_gadget_suspend") that removes the code of checking whether dwc->gadget_driver is NULL or not. It causes the following code is executed and deadlock occurs when trying to get the spinlock. In fact, the root cause is the commit 5265397f9442("usb: dwc3: Remove DWC3 locking during gadget suspend/resume") that forgot to remove the lock of otg mode. So, remove the redundant lock of otg mode during gadget suspend/resume.

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: Fix deadlock in ieee80211_sta_ps_deliver_wakeup() The ieee80211_sta_ps_deliver_wakeup() function takes sta->ps_lock to synchronizes with ieee80211_tx_h_unicast_ps_buf() which is called from softirq context. However using only spin_lock() to get sta->ps_lock in ieee80211_sta_ps_deliver_wakeup() does not prevent softirq to execute on this same CPU, to run ieee80211_tx_h_unicast_ps_buf() and try to take this same lock ending in deadlock. Below is an example of rcu stall that arises in such situation. rcu: INFO: rcu_sched self-detected stall on CPU rcu: 2-....: (42413413 ticks this GP) idle=b154/1/0x4000000000000000 softirq=1763/1765 fqs=21206996 rcu: (t=42586894 jiffies g=2057 q=362405 ncpus=4) CPU: 2 PID: 719 Comm: wpa_supplicant Tainted: G W 6.4.0-02158-g1b062f552873 #742 Hardware name: RPT (r1) (DT) pstate: 00000005 (nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : queued_spin_lock_slowpath+0x58/0x2d0 lr : invoke_tx_handlers_early+0x5b4/0x5c0 sp : ffff00001ef64660 x29: ffff00001ef64660 x28: ffff000009bc1070 x27: ffff000009bc0ad8 x26: ffff000009bc0900 x25: ffff00001ef647a8 x24: 0000000000000000 x23: ffff000009bc0900 x22: ffff000009bc0900 x21: ffff00000ac0e000 x20: ffff00000a279e00 x19: ffff00001ef646e8 x18: 0000000000000000 x17: ffff800016468000 x16: ffff00001ef608c0 x15: 0010533c93f64f80 x14: 0010395c9faa3946 x13: 0000000000000000 x12: 00000000fa83b2da x11: 000000012edeceea x10: ffff0000010fbe00 x9 : 0000000000895440 x8 : 000000000010533c x7 : ffff00000ad8b740 x6 : ffff00000c350880 x5 : 0000000000000007 x4 : 0000000000000001 x3 : 0000000000000000 x2 : 0000000000000000 x1 : 0000000000000001 x0 : ffff00000ac0e0e8 Call trace: queued_spin_lock_slowpath+0x58/0x2d0 ieee80211_tx+0x80/0x12c ieee80211_tx_pending+0x110/0x278 tasklet_action_common.constprop.0+0x10c/0x144 tasklet_action+0x20/0x28 _stext+0x11c/0x284 ____do_softirq+0xc/0x14 call_on_irq_stack+0x24/0x34 do_softirq_own_stack+0x18/0x20 do_softirq+0x74/0x7c __local_bh_enable_ip+0xa0/0xa4 _ieee80211_wake_txqs+0x3b0/0x4b8 __ieee80211_wake_queue+0x12c/0x168 ieee80211_add_pending_skbs+0xec/0x138 ieee80211_sta_ps_deliver_wakeup+0x2a4/0x480 ieee80211_mps_sta_status_update.part.0+0xd8/0x11c ieee80211_mps_sta_status_update+0x18/0x24 sta_apply_parameters+0x3bc/0x4c0 ieee80211_change_station+0x1b8/0x2dc nl80211_set_station+0x444/0x49c genl_family_rcv_msg_doit.isra.0+0xa4/0xfc genl_rcv_msg+0x1b0/0x244 netlink_rcv_skb+0x38/0x10c genl_rcv+0x34/0x48 netlink_unicast+0x254/0x2bc netlink_sendmsg+0x190/0x3b4 ____sys_sendmsg+0x1e8/0x218 ___sys_sendmsg+0x68/0x8c __sys_sendmsg+0x44/0x84 __arm64_sys_sendmsg+0x20/0x28 do_el0_svc+0x6c/0xe8 el0_svc+0x14/0x48 el0t_64_sync_handler+0xb0/0xb4 el0t_64_sync+0x14c/0x150 Using spin_lock_bh()/spin_unlock_bh() instead prevents softirq to raise on the same CPU that is holding the lock.

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7921s: fix potential hung tasks during chip recovery During chip recovery (e.g. chip reset), there is a possible situation that kernel worker reset_work is holding the lock and waiting for kernel thread stat_worker to be parked, while stat_worker is waiting for the release of the same lock. It causes a deadlock resulting in the dumping of hung tasks messages and possible rebooting of the device. This patch prevents the execution of stat_worker during the chip recovery.

In the Linux kernel, the following vulnerability has been resolved: net: ks8851: Fix deadlock with the SPI chip variant When SMP is enabled and spinlocks are actually functional then there is a deadlock with the 'statelock' spinlock between ks8851_start_xmit_spi and ks8851_irq: watchdog: BUG: soft lockup - CPU#0 stuck for 27s! call trace: queued_spin_lock_slowpath+0x100/0x284 do_raw_spin_lock+0x34/0x44 ks8851_start_xmit_spi+0x30/0xb8 ks8851_start_xmit+0x14/0x20 netdev_start_xmit+0x40/0x6c dev_hard_start_xmit+0x6c/0xbc sch_direct_xmit+0xa4/0x22c __qdisc_run+0x138/0x3fc qdisc_run+0x24/0x3c net_tx_action+0xf8/0x130 handle_softirqs+0x1ac/0x1f0 __do_softirq+0x14/0x20 ____do_softirq+0x10/0x1c call_on_irq_stack+0x3c/0x58 do_softirq_own_stack+0x1c/0x28 __irq_exit_rcu+0x54/0x9c irq_exit_rcu+0x10/0x1c el1_interrupt+0x38/0x50 el1h_64_irq_handler+0x18/0x24 el1h_64_irq+0x64/0x68 __netif_schedule+0x6c/0x80 netif_tx_wake_queue+0x38/0x48 ks8851_irq+0xb8/0x2c8 irq_thread_fn+0x2c/0x74 irq_thread+0x10c/0x1b0 kthread+0xc8/0xd8 ret_from_fork+0x10/0x20 This issue has not been identified earlier because tests were done on a device with SMP disabled and so spinlocks were actually NOPs. Now use spin_(un)lock_bh for TX queue related locking to avoid execution of softirq work synchronously that would lead to a deadlock.

In the Linux kernel, the following vulnerability has been resolved: i2c: lpi2c: Avoid calling clk_get_rate during transfer Instead of repeatedly calling clk_get_rate for each transfer, lock the clock rate and cache the value. A deadlock has been observed while adding tlv320aic32x4 audio codec to the system. When this clock provider adds its clock, the clk mutex is locked already, it needs to access i2c, which in return needs the mutex for clk_get_rate as well.

In the Linux kernel, the following vulnerability has been resolved: io_uring: fix possible deadlock in io_register_iowq_max_workers() The io_register_iowq_max_workers() function calls io_put_sq_data(), which acquires the sqd->lock without releasing the uring_lock. Similar to the commit 009ad9f0c6ee ("io_uring: drop ctx->uring_lock before acquiring sqd->lock"), this can lead to a potential deadlock situation. To resolve this issue, the uring_lock is released before calling io_put_sq_data(), and then it is re-acquired after the function call. This change ensures that the locks are acquired in the correct order, preventing the possibility of a deadlock.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_core: cancel all works upon hci_unregister_dev() syzbot is reporting that calling hci_release_dev() from hci_error_reset() due to hci_dev_put() from hci_error_reset() can cause deadlock at destroy_workqueue(), for hci_error_reset() is called from hdev->req_workqueue which destroy_workqueue() needs to flush. We need to make sure that hdev->{rx_work,cmd_work,tx_work} which are queued into hdev->workqueue and hdev->{power_on,error_reset} which are queued into hdev->req_workqueue are no longer running by the moment destroy_workqueue(hdev->workqueue); destroy_workqueue(hdev->req_workqueue); are called from hci_release_dev(). Call cancel_work_sync() on these work items from hci_unregister_dev() as soon as hdev->list is removed from hci_dev_list.

In the Linux kernel, the following vulnerability has been resolved: io_uring/rsrc: don't lock while !TASK_RUNNING There is a report of io_rsrc_ref_quiesce() locking a mutex while not TASK_RUNNING, which is due to forgetting restoring the state back after io_run_task_work_sig() and attempts to break out of the waiting loop. do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffff815d2494>] prepare_to_wait+0xa4/0x380 kernel/sched/wait.c:237 WARNING: CPU: 2 PID: 397056 at kernel/sched/core.c:10099 __might_sleep+0x114/0x160 kernel/sched/core.c:10099 RIP: 0010:__might_sleep+0x114/0x160 kernel/sched/core.c:10099 Call Trace: <TASK> __mutex_lock_common kernel/locking/mutex.c:585 [inline] __mutex_lock+0xb4/0x940 kernel/locking/mutex.c:752 io_rsrc_ref_quiesce+0x590/0x940 io_uring/rsrc.c:253 io_sqe_buffers_unregister+0xa2/0x340 io_uring/rsrc.c:799 __io_uring_register io_uring/register.c:424 [inline] __do_sys_io_uring_register+0x5b9/0x2400 io_uring/register.c:613 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xd8/0x270 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x6f/0x77

In the Linux kernel, the following vulnerability has been resolved: ext4: do not create EA inode under buffer lock ext4_xattr_set_entry() creates new EA inodes while holding buffer lock on the external xattr block. This is problematic as it nests all the allocation locking (which acquires locks on other buffers) under the buffer lock. This can even deadlock when the filesystem is corrupted and e.g. quota file is setup to contain xattr block as data block. Move the allocation of EA inode out of ext4_xattr_set_entry() into the callers.

In the Linux kernel, the following vulnerability has been resolved: f2fs: don't set RO when shutting down f2fs Shutdown does not check the error of thaw_super due to readonly, which causes a deadlock like below. f2fs_ioc_shutdown(F2FS_GOING_DOWN_FULLSYNC) issue_discard_thread - bdev_freeze - freeze_super - f2fs_stop_checkpoint() - f2fs_handle_critical_error - sb_start_write - set RO - waiting - bdev_thaw - thaw_super_locked - return -EINVAL, if sb_rdonly() - f2fs_stop_discard_thread -> wait for kthread_stop(discard_thread);

In the Linux kernel, the following vulnerability has been resolved: md/raid5: fix deadlock that raid5d() wait for itself to clear MD_SB_CHANGE_PENDING Xiao reported that lvm2 test lvconvert-raid-takeover.sh can hang with small possibility, the root cause is exactly the same as commit bed9e27baf52 ("Revert "md/raid5: Wait for MD_SB_CHANGE_PENDING in raid5d"") However, Dan reported another hang after that, and junxiao investigated the problem and found out that this is caused by plugged bio can't issue from raid5d(). Current implementation in raid5d() has a weird dependence: 1) md_check_recovery() from raid5d() must hold 'reconfig_mutex' to clear MD_SB_CHANGE_PENDING; 2) raid5d() handles IO in a deadloop, until all IO are issued; 3) IO from raid5d() must wait for MD_SB_CHANGE_PENDING to be cleared; This behaviour is introduce before v2.6, and for consequence, if other context hold 'reconfig_mutex', and md_check_recovery() can't update super_block, then raid5d() will waste one cpu 100% by the deadloop, until 'reconfig_mutex' is released. Refer to the implementation from raid1 and raid10, fix this problem by skipping issue IO if MD_SB_CHANGE_PENDING is still set after md_check_recovery(), daemon thread will be woken up when 'reconfig_mutex' is released. Meanwhile, the hang problem will be fixed as well.

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix deadlock in smb2_find_smb_tcon() Unlock cifs_tcp_ses_lock before calling cifs_put_smb_ses() to avoid such deadlock.

In the Linux kernel, the following vulnerability has been resolved: netrom: fix possible dead-lock in nr_rt_ioctl() syzbot loves netrom, and found a possible deadlock in nr_rt_ioctl [1] Make sure we always acquire nr_node_list_lock before nr_node_lock(nr_node) [1] WARNING: possible circular locking dependency detected 6.9.0-rc7-syzkaller-02147-g654de42f3fc6 #0 Not tainted ------------------------------------------------------ syz-executor350/5129 is trying to acquire lock: ffff8880186e2070 (&nr_node->node_lock){+...}-{2:2}, at: spin_lock_bh include/linux/spinlock.h:356 [inline] ffff8880186e2070 (&nr_node->node_lock){+...}-{2:2}, at: nr_node_lock include/net/netrom.h:152 [inline] ffff8880186e2070 (&nr_node->node_lock){+...}-{2:2}, at: nr_dec_obs net/netrom/nr_route.c:464 [inline] ffff8880186e2070 (&nr_node->node_lock){+...}-{2:2}, at: nr_rt_ioctl+0x1bb/0x1090 net/netrom/nr_route.c:697 but task is already holding lock: ffffffff8f7053b8 (nr_node_list_lock){+...}-{2:2}, at: spin_lock_bh include/linux/spinlock.h:356 [inline] ffffffff8f7053b8 (nr_node_list_lock){+...}-{2:2}, at: nr_dec_obs net/netrom/nr_route.c:462 [inline] ffffffff8f7053b8 (nr_node_list_lock){+...}-{2:2}, at: nr_rt_ioctl+0x10a/0x1090 net/netrom/nr_route.c:697 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (nr_node_list_lock){+...}-{2:2}: lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5754 __raw_spin_lock_bh include/linux/spinlock_api_smp.h:126 [inline] _raw_spin_lock_bh+0x35/0x50 kernel/locking/spinlock.c:178 spin_lock_bh include/linux/spinlock.h:356 [inline] nr_remove_node net/netrom/nr_route.c:299 [inline] nr_del_node+0x4b4/0x820 net/netrom/nr_route.c:355 nr_rt_ioctl+0xa95/0x1090 net/netrom/nr_route.c:683 sock_do_ioctl+0x158/0x460 net/socket.c:1222 sock_ioctl+0x629/0x8e0 net/socket.c:1341 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:904 [inline] __se_sys_ioctl+0xfc/0x170 fs/ioctl.c:890 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf5/0x240 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f -> #0 (&nr_node->node_lock){+...}-{2:2}: check_prev_add kernel/locking/lockdep.c:3134 [inline] check_prevs_add kernel/locking/lockdep.c:3253 [inline] validate_chain+0x18cb/0x58e0 kernel/locking/lockdep.c:3869 __lock_acquire+0x1346/0x1fd0 kernel/locking/lockdep.c:5137 lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5754 __raw_spin_lock_bh include/linux/spinlock_api_smp.h:126 [inline] _raw_spin_lock_bh+0x35/0x50 kernel/locking/spinlock.c:178 spin_lock_bh include/linux/spinlock.h:356 [inline] nr_node_lock include/net/netrom.h:152 [inline] nr_dec_obs net/netrom/nr_route.c:464 [inline] nr_rt_ioctl+0x1bb/0x1090 net/netrom/nr_route.c:697 sock_do_ioctl+0x158/0x460 net/socket.c:1222 sock_ioctl+0x629/0x8e0 net/socket.c:1341 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:904 [inline] __se_sys_ioctl+0xfc/0x170 fs/ioctl.c:890 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf5/0x240 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(nr_node_list_lock); lock(&nr_node->node_lock); lock(nr_node_list_lock); lock(&nr_node->node_lock); *** DEADLOCK *** 1 lock held by syz-executor350/5129: #0: ffffffff8f7053b8 (nr_node_list_lock){+...}-{2:2}, at: spin_lock_bh include/linux/spinlock.h:356 [inline] #0: ffffffff8f7053b8 (nr_node_list_lock){+...}-{2:2}, at: nr_dec_obs net/netrom/nr_route.c:462 [inline] #0: ffffffff8f70 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: net: fec: remove .ndo_poll_controller to avoid deadlocks There is a deadlock issue found in sungem driver, please refer to the commit ac0a230f719b ("eth: sungem: remove .ndo_poll_controller to avoid deadlocks"). The root cause of the issue is that netpoll is in atomic context and disable_irq() is called by .ndo_poll_controller interface of sungem driver, however, disable_irq() might sleep. After analyzing the implementation of fec_poll_controller(), the fec driver should have the same issue. Due to the fec driver uses NAPI for TX completions, the .ndo_poll_controller is unnecessary to be implemented in the fec driver, so fec_poll_controller() can be safely removed.

In the Linux kernel, the following vulnerability has been resolved: serial: max3100: Lock port->lock when calling uart_handle_cts_change() uart_handle_cts_change() has to be called with port lock taken, Since we run it in a separate work, the lock may not be taken at the time of running. Make sure that it's taken by explicitly doing that. Without it we got a splat: WARNING: CPU: 0 PID: 10 at drivers/tty/serial/serial_core.c:3491 uart_handle_cts_change+0xa6/0xb0 ... Workqueue: max3100-0 max3100_work [max3100] RIP: 0010:uart_handle_cts_change+0xa6/0xb0 ... max3100_handlerx+0xc5/0x110 [max3100] max3100_work+0x12a/0x340 [max3100]

In the Linux kernel, the following vulnerability has been resolved: dma-buf/sw-sync: don't enable IRQ from sync_print_obj() Since commit a6aa8fca4d79 ("dma-buf/sw-sync: Reduce irqsave/irqrestore from known context") by error replaced spin_unlock_irqrestore() with spin_unlock_irq() for both sync_debugfs_show() and sync_print_obj() despite sync_print_obj() is called from sync_debugfs_show(), lockdep complains inconsistent lock state warning. Use plain spin_{lock,unlock}() for sync_print_obj(), for sync_debugfs_show() is already using spin_{lock,unlock}_irq().

In the Linux kernel, the following vulnerability has been resolved: eth: sungem: remove .ndo_poll_controller to avoid deadlocks Erhard reports netpoll warnings from sungem: netpoll_send_skb_on_dev(): eth0 enabled interrupts in poll (gem_start_xmit+0x0/0x398) WARNING: CPU: 1 PID: 1 at net/core/netpoll.c:370 netpoll_send_skb+0x1fc/0x20c gem_poll_controller() disables interrupts, which may sleep. We can't sleep in netpoll, it has interrupts disabled completely. Strangely, gem_poll_controller() doesn't even poll the completions, and instead acts as if an interrupt has fired so it just schedules NAPI and exits. None of this has been necessary for years, since netpoll invokes NAPI directly.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Reload only IB representors upon lag disable/enable On lag disable, the bond IB device along with all of its representors are destroyed, and then the slaves' representors get reloaded. In case the slave IB representor load fails, the eswitch error flow unloads all representors, including ethernet representors, where the netdevs get detached and removed from lag bond. Such flow is inaccurate as the lag driver is not responsible for loading/unloading ethernet representors. Furthermore, the flow described above begins by holding lag lock to prevent bond changes during disable flow. However, when reaching the ethernet representors detachment from lag, the lag lock is required again, triggering the following deadlock: Call trace: __switch_to+0xf4/0x148 __schedule+0x2c8/0x7d0 schedule+0x50/0xe0 schedule_preempt_disabled+0x18/0x28 __mutex_lock.isra.13+0x2b8/0x570 __mutex_lock_slowpath+0x1c/0x28 mutex_lock+0x4c/0x68 mlx5_lag_remove_netdev+0x3c/0x1a0 [mlx5_core] mlx5e_uplink_rep_disable+0x70/0xa0 [mlx5_core] mlx5e_detach_netdev+0x6c/0xb0 [mlx5_core] mlx5e_netdev_change_profile+0x44/0x138 [mlx5_core] mlx5e_netdev_attach_nic_profile+0x28/0x38 [mlx5_core] mlx5e_vport_rep_unload+0x184/0x1b8 [mlx5_core] mlx5_esw_offloads_rep_load+0xd8/0xe0 [mlx5_core] mlx5_eswitch_reload_reps+0x74/0xd0 [mlx5_core] mlx5_disable_lag+0x130/0x138 [mlx5_core] mlx5_lag_disable_change+0x6c/0x70 [mlx5_core] // hold ldev->lock mlx5_devlink_eswitch_mode_set+0xc0/0x410 [mlx5_core] devlink_nl_cmd_eswitch_set_doit+0xdc/0x180 genl_family_rcv_msg_doit.isra.17+0xe8/0x138 genl_rcv_msg+0xe4/0x220 netlink_rcv_skb+0x44/0x108 genl_rcv+0x40/0x58 netlink_unicast+0x198/0x268 netlink_sendmsg+0x1d4/0x418 sock_sendmsg+0x54/0x60 __sys_sendto+0xf4/0x120 __arm64_sys_sendto+0x30/0x40 el0_svc_common+0x8c/0x120 do_el0_svc+0x30/0xa0 el0_svc+0x20/0x30 el0_sync_handler+0x90/0xb8 el0_sync+0x160/0x180 Thus, upon lag enable/disable, load and unload only the IB representors of the slaves preventing the deadlock mentioned above. While at it, refactor the mlx5_esw_offloads_rep_load() function to have a static helper method for its internal logic, in symmetry with the representor unload design.

In the Linux kernel, the following vulnerability has been resolved: net: ks8851: Handle softirqs at the end of IRQ thread to fix hang The ks8851_irq() thread may call ks8851_rx_pkts() in case there are any packets in the MAC FIFO, which calls netif_rx(). This netif_rx() implementation is guarded by local_bh_disable() and local_bh_enable(). The local_bh_enable() may call do_softirq() to run softirqs in case any are pending. One of the softirqs is net_rx_action, which ultimately reaches the driver .start_xmit callback. If that happens, the system hangs. The entire call chain is below: ks8851_start_xmit_par from netdev_start_xmit netdev_start_xmit from dev_hard_start_xmit dev_hard_start_xmit from sch_direct_xmit sch_direct_xmit from __dev_queue_xmit __dev_queue_xmit from __neigh_update __neigh_update from neigh_update neigh_update from arp_process.constprop.0 arp_process.constprop.0 from __netif_receive_skb_one_core __netif_receive_skb_one_core from process_backlog process_backlog from __napi_poll.constprop.0 __napi_poll.constprop.0 from net_rx_action net_rx_action from __do_softirq __do_softirq from call_with_stack call_with_stack from do_softirq do_softirq from __local_bh_enable_ip __local_bh_enable_ip from netif_rx netif_rx from ks8851_irq ks8851_irq from irq_thread_fn irq_thread_fn from irq_thread irq_thread from kthread kthread from ret_from_fork The hang happens because ks8851_irq() first locks a spinlock in ks8851_par.c ks8851_lock_par() spin_lock_irqsave(&ksp->lock, ...) and with that spinlock locked, calls netif_rx(). Once the execution reaches ks8851_start_xmit_par(), it calls ks8851_lock_par() again which attempts to claim the already locked spinlock again, and the hang happens. Move the do_softirq() call outside of the spinlock protected section of ks8851_irq() by disabling BHs around the entire spinlock protected section of ks8851_irq() handler. Place local_bh_enable() outside of the spinlock protected section, so that it can trigger do_softirq() without the ks8851_par.c ks8851_lock_par() spinlock being held, and safely call ks8851_start_xmit_par() without attempting to lock the already locked spinlock. Since ks8851_irq() is protected by local_bh_disable()/local_bh_enable() now, replace netif_rx() with __netif_rx() which is not duplicating the local_bh_disable()/local_bh_enable() calls.

In the Linux kernel, the following vulnerability has been resolved: pds_core: Fix pdsc_check_pci_health function to use work thread When the driver notices fw_status == 0xff it tries to perform a PCI reset on itself via pci_reset_function() in the context of the driver's health thread. However, pdsc_reset_prepare calls pdsc_stop_health_thread(), which attempts to stop/flush the health thread. This results in a deadlock because the stop/flush will never complete since the driver called pci_reset_function() from the health thread context. Fix by changing the pdsc_check_pci_health_function() to queue a newly introduced pdsc_pci_reset_thread() on the pdsc's work queue. Unloading the driver in the fw_down/dead state uncovered another issue, which can be seen in the following trace: WARNING: CPU: 51 PID: 6914 at kernel/workqueue.c:1450 __queue_work+0x358/0x440 [...] RIP: 0010:__queue_work+0x358/0x440 [...] Call Trace: <TASK> ? __warn+0x85/0x140 ? __queue_work+0x358/0x440 ? report_bug+0xfc/0x1e0 ? handle_bug+0x3f/0x70 ? exc_invalid_op+0x17/0x70 ? asm_exc_invalid_op+0x1a/0x20 ? __queue_work+0x358/0x440 queue_work_on+0x28/0x30 pdsc_devcmd_locked+0x96/0xe0 [pds_core] pdsc_devcmd_reset+0x71/0xb0 [pds_core] pdsc_teardown+0x51/0xe0 [pds_core] pdsc_remove+0x106/0x200 [pds_core] pci_device_remove+0x37/0xc0 device_release_driver_internal+0xae/0x140 driver_detach+0x48/0x90 bus_remove_driver+0x6d/0xf0 pci_unregister_driver+0x2e/0xa0 pdsc_cleanup_module+0x10/0x780 [pds_core] __x64_sys_delete_module+0x142/0x2b0 ? syscall_trace_enter.isra.18+0x126/0x1a0 do_syscall_64+0x3b/0x90 entry_SYSCALL_64_after_hwframe+0x72/0xdc RIP: 0033:0x7fbd9d03a14b [...] Fix this by preventing the devcmd reset if the FW is not running.

In the Linux kernel, the following vulnerability has been resolved: dmaengine: idxd: Convert spinlock to mutex to lock evl workqueue drain_workqueue() cannot be called safely in a spinlocked context due to possible task rescheduling. In the multi-task scenario, calling queue_work() while drain_workqueue() will lead to a Call Trace as pushing a work on a draining workqueue is not permitted in spinlocked context. Call Trace: <TASK> ? __warn+0x7d/0x140 ? __queue_work+0x2b2/0x440 ? report_bug+0x1f8/0x200 ? handle_bug+0x3c/0x70 ? exc_invalid_op+0x18/0x70 ? asm_exc_invalid_op+0x1a/0x20 ? __queue_work+0x2b2/0x440 queue_work_on+0x28/0x30 idxd_misc_thread+0x303/0x5a0 [idxd] ? __schedule+0x369/0xb40 ? __pfx_irq_thread_fn+0x10/0x10 ? irq_thread+0xbc/0x1b0 irq_thread_fn+0x21/0x70 irq_thread+0x102/0x1b0 ? preempt_count_add+0x74/0xa0 ? __pfx_irq_thread_dtor+0x10/0x10 ? __pfx_irq_thread+0x10/0x10 kthread+0x103/0x140 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x31/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1b/0x30 </TASK> The current implementation uses a spinlock to protect event log workqueue and will lead to the Call Trace due to potential task rescheduling. To address the locking issue, convert the spinlock to mutex, allowing the drain_workqueue() to be called in a safe mutex-locked context. This change ensures proper synchronization when accessing the event log workqueue, preventing potential Call Trace and improving the overall robustness of the code.

In the Linux kernel, the following vulnerability has been resolved: nfsd: Fix error cleanup path in nfsd_rename() Commit a8b0026847b8 ("rename(): avoid a deadlock in the case of parents having no common ancestor") added an error bail out path. However this path does not drop the remount protection that has been acquired. Fix the cleanup path to properly drop the remount protection.

In the Linux kernel, the following vulnerability has been resolved: bpf, sockmap: Prevent lock inversion deadlock in map delete elem syzkaller started using corpuses where a BPF tracing program deletes elements from a sockmap/sockhash map. Because BPF tracing programs can be invoked from any interrupt context, locks taken during a map_delete_elem operation must be hardirq-safe. Otherwise a deadlock due to lock inversion is possible, as reported by lockdep: CPU0 CPU1 ---- ---- lock(&htab->buckets[i].lock); local_irq_disable(); lock(&host->lock); lock(&htab->buckets[i].lock); <Interrupt> lock(&host->lock); Locks in sockmap are hardirq-unsafe by design. We expects elements to be deleted from sockmap/sockhash only in task (normal) context with interrupts enabled, or in softirq context. Detect when map_delete_elem operation is invoked from a context which is _not_ hardirq-unsafe, that is interrupts are disabled, and bail out with an error. Note that map updates are not affected by this issue. BPF verifier does not allow updating sockmap/sockhash from a BPF tracing program today.

In the Linux kernel, the following vulnerability has been resolved: scsi: bnx2fc: Remove spin_lock_bh while releasing resources after upload The session resources are used by FW and driver when session is offloaded, once session is uploaded these resources are not used. The lock is not required as these fields won't be used any longer. The offload and upload calls are sequential, hence lock is not required. This will suppress following BUG_ON(): [ 449.843143] ------------[ cut here ]------------ [ 449.848302] kernel BUG at mm/vmalloc.c:2727! [ 449.853072] invalid opcode: 0000 [#1] PREEMPT SMP PTI [ 449.858712] CPU: 5 PID: 1996 Comm: kworker/u24:2 Not tainted 5.14.0-118.el9.x86_64 #1 Rebooting. [ 449.867454] Hardware name: Dell Inc. PowerEdge R730/0WCJNT, BIOS 2.3.4 11/08/2016 [ 449.876966] Workqueue: fc_rport_eq fc_rport_work [libfc] [ 449.882910] RIP: 0010:vunmap+0x2e/0x30 [ 449.887098] Code: 00 65 8b 05 14 a2 f0 4a a9 00 ff ff 00 75 1b 55 48 89 fd e8 34 36 79 00 48 85 ed 74 0b 48 89 ef 31 f6 5d e9 14 fc ff ff 5d c3 <0f> 0b 0f 1f 44 00 00 41 57 41 56 49 89 ce 41 55 49 89 fd 41 54 41 [ 449.908054] RSP: 0018:ffffb83d878b3d68 EFLAGS: 00010206 [ 449.913887] RAX: 0000000080000201 RBX: ffff8f4355133550 RCX: 000000000d400005 [ 449.921843] RDX: 0000000000000001 RSI: 0000000000001000 RDI: ffffb83da53f5000 [ 449.929808] RBP: ffff8f4ac6675800 R08: ffffb83d878b3d30 R09: 00000000000efbdf [ 449.937774] R10: 0000000000000003 R11: ffff8f434573e000 R12: 0000000000001000 [ 449.945736] R13: 0000000000001000 R14: ffffb83da53f5000 R15: ffff8f43d4ea3ae0 [ 449.953701] FS: 0000000000000000(0000) GS:ffff8f529fc80000(0000) knlGS:0000000000000000 [ 449.962732] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 449.969138] CR2: 00007f8cf993e150 CR3: 0000000efbe10003 CR4: 00000000003706e0 [ 449.977102] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 449.985065] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 449.993028] Call Trace: [ 449.995756] __iommu_dma_free+0x96/0x100 [ 450.000139] bnx2fc_free_session_resc+0x67/0x240 [bnx2fc] [ 450.006171] bnx2fc_upload_session+0xce/0x100 [bnx2fc] [ 450.011910] bnx2fc_rport_event_handler+0x9f/0x240 [bnx2fc] [ 450.018136] fc_rport_work+0x103/0x5b0 [libfc] [ 450.023103] process_one_work+0x1e8/0x3c0 [ 450.027581] worker_thread+0x50/0x3b0 [ 450.031669] ? rescuer_thread+0x370/0x370 [ 450.036143] kthread+0x149/0x170 [ 450.039744] ? set_kthread_struct+0x40/0x40 [ 450.044411] ret_from_fork+0x22/0x30 [ 450.048404] Modules linked in: vfat msdos fat xfs nfs_layout_nfsv41_files rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver dm_service_time qedf qed crc8 bnx2fc libfcoe libfc scsi_transport_fc intel_rapl_msr intel_rapl_common x86_pkg_temp_thermal intel_powerclamp dcdbas rapl intel_cstate intel_uncore mei_me pcspkr mei ipmi_ssif lpc_ich ipmi_si fuse zram ext4 mbcache jbd2 loop nfsv3 nfs_acl nfs lockd grace fscache netfs irdma ice sd_mod t10_pi sg ib_uverbs ib_core 8021q garp mrp stp llc mgag200 i2c_algo_bit drm_kms_helper syscopyarea sysfillrect sysimgblt mxm_wmi fb_sys_fops cec crct10dif_pclmul ahci crc32_pclmul bnx2x drm ghash_clmulni_intel libahci rfkill i40e libata megaraid_sas mdio wmi sunrpc lrw dm_crypt dm_round_robin dm_multipath dm_snapshot dm_bufio dm_mirror dm_region_hash dm_log dm_zero dm_mod linear raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx raid6_pq libcrc32c crc32c_intel raid1 raid0 iscsi_ibft squashfs be2iscsi bnx2i cnic uio cxgb4i cxgb4 tls [ 450.048497] libcxgbi libcxgb qla4xxx iscsi_boot_sysfs iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi edd ipmi_devintf ipmi_msghandler [ 450.159753] ---[ end trace 712de2c57c64abc8 ]---

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Release hbalock before calling lpfc_worker_wake_up() lpfc_worker_wake_up() calls the lpfc_work_done() routine, which takes the hbalock. Thus, lpfc_worker_wake_up() should not be called while holding the hbalock to avoid potential deadlock.

In the Linux kernel, the following vulnerability has been resolved: Revert "media: v4l2-ctrls: show all owned controls in log_status" This reverts commit 9801b5b28c6929139d6fceeee8d739cc67bb2739. This patch introduced a potential deadlock scenario: [Wed May 8 10:02:06 2024] Possible unsafe locking scenario: [Wed May 8 10:02:06 2024] CPU0 CPU1 [Wed May 8 10:02:06 2024] ---- ---- [Wed May 8 10:02:06 2024] lock(vivid_ctrls:1620:(hdl_vid_cap)->_lock); [Wed May 8 10:02:06 2024] lock(vivid_ctrls:1608:(hdl_user_vid)->_lock); [Wed May 8 10:02:06 2024] lock(vivid_ctrls:1620:(hdl_vid_cap)->_lock); [Wed May 8 10:02:06 2024] lock(vivid_ctrls:1608:(hdl_user_vid)->_lock); For now just revert.

In the Linux kernel, the following vulnerability has been resolved: dma: xilinx_dpdma: Fix locking There are several places where either chan->lock or chan->vchan.lock was not held. Add appropriate locking. This fixes lockdep warnings like [ 31.077578] ------------[ cut here ]------------ [ 31.077831] WARNING: CPU: 2 PID: 40 at drivers/dma/xilinx/xilinx_dpdma.c:834 xilinx_dpdma_chan_queue_transfer+0x274/0x5e0 [ 31.077953] Modules linked in: [ 31.078019] CPU: 2 PID: 40 Comm: kworker/u12:1 Not tainted 6.6.20+ #98 [ 31.078102] Hardware name: xlnx,zynqmp (DT) [ 31.078169] Workqueue: events_unbound deferred_probe_work_func [ 31.078272] pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 31.078377] pc : xilinx_dpdma_chan_queue_transfer+0x274/0x5e0 [ 31.078473] lr : xilinx_dpdma_chan_queue_transfer+0x270/0x5e0 [ 31.078550] sp : ffffffc083bb2e10 [ 31.078590] x29: ffffffc083bb2e10 x28: 0000000000000000 x27: ffffff880165a168 [ 31.078754] x26: ffffff880164e920 x25: ffffff880164eab8 x24: ffffff880164d480 [ 31.078920] x23: ffffff880165a148 x22: ffffff880164e988 x21: 0000000000000000 [ 31.079132] x20: ffffffc082aa3000 x19: ffffff880164e880 x18: 0000000000000000 [ 31.079295] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 [ 31.079453] x14: 0000000000000000 x13: ffffff8802263dc0 x12: 0000000000000001 [ 31.079613] x11: 0001ffc083bb2e34 x10: 0001ff880164e98f x9 : 0001ffc082aa3def [ 31.079824] x8 : 0001ffc082aa3dec x7 : 0000000000000000 x6 : 0000000000000516 [ 31.079982] x5 : ffffffc7f8d43000 x4 : ffffff88003c9c40 x3 : ffffffffffffffff [ 31.080147] x2 : ffffffc7f8d43000 x1 : 00000000000000c0 x0 : 0000000000000000 [ 31.080307] Call trace: [ 31.080340] xilinx_dpdma_chan_queue_transfer+0x274/0x5e0 [ 31.080518] xilinx_dpdma_issue_pending+0x11c/0x120 [ 31.080595] zynqmp_disp_layer_update+0x180/0x3ac [ 31.080712] zynqmp_dpsub_plane_atomic_update+0x11c/0x21c [ 31.080825] drm_atomic_helper_commit_planes+0x20c/0x684 [ 31.080951] drm_atomic_helper_commit_tail+0x5c/0xb0 [ 31.081139] commit_tail+0x234/0x294 [ 31.081246] drm_atomic_helper_commit+0x1f8/0x210 [ 31.081363] drm_atomic_commit+0x100/0x140 [ 31.081477] drm_client_modeset_commit_atomic+0x318/0x384 [ 31.081634] drm_client_modeset_commit_locked+0x8c/0x24c [ 31.081725] drm_client_modeset_commit+0x34/0x5c [ 31.081812] __drm_fb_helper_restore_fbdev_mode_unlocked+0x104/0x168 [ 31.081899] drm_fb_helper_set_par+0x50/0x70 [ 31.081971] fbcon_init+0x538/0xc48 [ 31.082047] visual_init+0x16c/0x23c [ 31.082207] do_bind_con_driver.isra.0+0x2d0/0x634 [ 31.082320] do_take_over_console+0x24c/0x33c [ 31.082429] do_fbcon_takeover+0xbc/0x1b0 [ 31.082503] fbcon_fb_registered+0x2d0/0x34c [ 31.082663] register_framebuffer+0x27c/0x38c [ 31.082767] __drm_fb_helper_initial_config_and_unlock+0x5c0/0x91c [ 31.082939] drm_fb_helper_initial_config+0x50/0x74 [ 31.083012] drm_fbdev_dma_client_hotplug+0xb8/0x108 [ 31.083115] drm_client_register+0xa0/0xf4 [ 31.083195] drm_fbdev_dma_setup+0xb0/0x1cc [ 31.083293] zynqmp_dpsub_drm_init+0x45c/0x4e0 [ 31.083431] zynqmp_dpsub_probe+0x444/0x5e0 [ 31.083616] platform_probe+0x8c/0x13c [ 31.083713] really_probe+0x258/0x59c [ 31.083793] __driver_probe_device+0xc4/0x224 [ 31.083878] driver_probe_device+0x70/0x1c0 [ 31.083961] __device_attach_driver+0x108/0x1e0 [ 31.084052] bus_for_each_drv+0x9c/0x100 [ 31.084125] __device_attach+0x100/0x298 [ 31.084207] device_initial_probe+0x14/0x20 [ 31.084292] bus_probe_device+0xd8/0xdc [ 31.084368] deferred_probe_work_func+0x11c/0x180 [ 31.084451] process_one_work+0x3ac/0x988 [ 31.084643] worker_thread+0x398/0x694 [ 31.084752] kthread+0x1bc/0x1c0 [ 31.084848] ret_from_fork+0x10/0x20 [ 31.084932] irq event stamp: 64549 [ 31.084970] hardirqs last enabled at (64548): [<ffffffc081adf35c>] _raw_spin_unlock_irqrestore+0x80/0x90 [ 31.085157] ---truncated---

In the Linux kernel, the following vulnerability has been resolved: md/dm-raid: don't call md_reap_sync_thread() directly Currently md_reap_sync_thread() is called from raid_message() directly without holding 'reconfig_mutex', this is definitely unsafe because md_reap_sync_thread() can change many fields that is protected by 'reconfig_mutex'. However, hold 'reconfig_mutex' here is still problematic because this will cause deadlock, for example, commit 130443d60b1b ("md: refactor idle/frozen_sync_thread() to fix deadlock"). Fix this problem by using stop_sync_thread() to unregister sync_thread, like md/raid did.

In the Linux kernel, the following vulnerability has been resolved: smb3: missing lock when picking channel Coverity spotted a place where we should have been holding the channel lock when accessing the ses channel index. Addresses-Coverity: 1582039 ("Data race condition (MISSING_LOCK)")

In the Linux kernel, the following vulnerability has been resolved: Reapply "drm/qxl: simplify qxl_fence_wait" This reverts commit 07ed11afb68d94eadd4ffc082b97c2331307c5ea. Stephen Rostedt reports: "I went to run my tests on my VMs and the tests hung on boot up. Unfortunately, the most I ever got out was: [ 93.607888] Testing event system initcall: OK [ 93.667730] Running tests on all trace events: [ 93.669757] Testing all events: OK [ 95.631064] ------------[ cut here ]------------ Timed out after 60 seconds" and further debugging points to a possible circular locking dependency between the console_owner locking and the worker pool locking. Reverting the commit allows Steve's VM to boot to completion again. [ This may obviously result in the "[TTM] Buffer eviction failed" messages again, which was the reason for that original revert. But at this point this seems preferable to a non-booting system... ]

In the Linux kernel, the following vulnerability has been resolved: thermal/debugfs: Fix two locking issues with thermal zone debug With the current thermal zone locking arrangement in the debugfs code, user space can open the "mitigations" file for a thermal zone before the zone's debugfs pointer is set which will result in a NULL pointer dereference in tze_seq_start(). Moreover, thermal_debug_tz_remove() is not called under the thermal zone lock, so it can run in parallel with the other functions accessing the thermal zone's struct thermal_debugfs object. Then, it may clear tz->debugfs after one of those functions has checked it and the struct thermal_debugfs object may be freed prematurely. To address the first problem, pass a pointer to the thermal zone's struct thermal_debugfs object to debugfs_create_file() in thermal_debug_tz_add() and make tze_seq_start(), tze_seq_next(), tze_seq_stop(), and tze_seq_show() retrieve it from s->private instead of a pointer to the thermal zone object. This will ensure that tz_debugfs will be valid across the "mitigations" file accesses until thermal_debugfs_remove_id() called by thermal_debug_tz_remove() removes that file. To address the second problem, use tz->lock in thermal_debug_tz_remove() around the tz->debugfs value check (in case the same thermal zone is removed at the same time in two different threads) and its reset to NULL. Cc :6.8+ <stable@vger.kernel.org> # 6.8+

In the Linux kernel, the following vulnerability has been resolved: HID: i2c-hid: remove I2C_HID_READ_PENDING flag to prevent lock-up The flag I2C_HID_READ_PENDING is used to serialize I2C operations. However, this is not necessary, because I2C core already has its own locking for that. More importantly, this flag can cause a lock-up: if the flag is set in i2c_hid_xfer() and an interrupt happens, the interrupt handler (i2c_hid_irq) will check this flag and return immediately without doing anything, then the interrupt handler will be invoked again in an infinite loop. Since interrupt handler is an RT task, it takes over the CPU and the flag-clearing task never gets scheduled, thus we have a lock-up. Delete this unnecessary flag.

In the Linux kernel, the following vulnerability has been resolved: drm/ast: Fix soft lockup There is a while-loop in ast_dp_set_on_off() that could lead to infinite-loop. This is because the register, VGACRI-Dx, checked in this API is a scratch register actually controlled by a MCU, named DPMCU, in BMC. These scratch registers are protected by scu-lock. If suc-lock is not off, DPMCU can not update these registers and then host will have soft lockup due to never updated status. DPMCU is used to control DP and relative registers to handshake with host's VGA driver. Even the most time-consuming task, DP's link training, is less than 100ms. 200ms should be enough.

In the Linux kernel, the following vulnerability has been resolved: efi/unaccepted: touch soft lockup during memory accept Commit 50e782a86c98 ("efi/unaccepted: Fix soft lockups caused by parallel memory acceptance") has released the spinlock so other CPUs can do memory acceptance in parallel and not triggers softlockup on other CPUs. However the softlock up was intermittent shown up if the memory of the TD guest is large, and the timeout of softlockup is set to 1 second: RIP: 0010:_raw_spin_unlock_irqrestore Call Trace: ? __hrtimer_run_queues <IRQ> ? hrtimer_interrupt ? watchdog_timer_fn ? __sysvec_apic_timer_interrupt ? __pfx_watchdog_timer_fn ? sysvec_apic_timer_interrupt </IRQ> ? __hrtimer_run_queues <TASK> ? hrtimer_interrupt ? asm_sysvec_apic_timer_interrupt ? _raw_spin_unlock_irqrestore ? __sysvec_apic_timer_interrupt ? sysvec_apic_timer_interrupt accept_memory try_to_accept_memory do_huge_pmd_anonymous_page get_page_from_freelist __handle_mm_fault __alloc_pages __folio_alloc ? __tdx_hypercall handle_mm_fault vma_alloc_folio do_user_addr_fault do_huge_pmd_anonymous_page exc_page_fault ? __do_huge_pmd_anonymous_page asm_exc_page_fault __handle_mm_fault When the local irq is enabled at the end of accept_memory(), the softlockup detects that the watchdog on single CPU has not been fed for a while. That is to say, even other CPUs will not be blocked by spinlock, the current CPU might be stunk with local irq disabled for a while, which hurts not only nmi watchdog but also softlockup. Chao Gao pointed out that the memory accept could be time costly and there was similar report before. Thus to avoid any softlocup detection during this stage, give the softlockup a flag to skip the timeout check at the end of accept_memory(), by invoking touch_softlockup_watchdog().

In the Linux kernel, the following vulnerability has been resolved: net/sched: fix lockdep splat in qdisc_tree_reduce_backlog() qdisc_tree_reduce_backlog() is called with the qdisc lock held, not RTNL. We must use qdisc_lookup_rcu() instead of qdisc_lookup() syzbot reported: WARNING: suspicious RCU usage 6.1.74-syzkaller #0 Not tainted ----------------------------- net/sched/sch_api.c:305 suspicious rcu_dereference_protected() usage! other info that might help us debug this: rcu_scheduler_active = 2, debug_locks = 1 3 locks held by udevd/1142: #0: ffffffff87c729a0 (rcu_read_lock){....}-{1:2}, at: rcu_lock_acquire include/linux/rcupdate.h:306 [inline] #0: ffffffff87c729a0 (rcu_read_lock){....}-{1:2}, at: rcu_read_lock include/linux/rcupdate.h:747 [inline] #0: ffffffff87c729a0 (rcu_read_lock){....}-{1:2}, at: net_tx_action+0x64a/0x970 net/core/dev.c:5282 #1: ffff888171861108 (&sch->q.lock){+.-.}-{2:2}, at: spin_lock include/linux/spinlock.h:350 [inline] #1: ffff888171861108 (&sch->q.lock){+.-.}-{2:2}, at: net_tx_action+0x754/0x970 net/core/dev.c:5297 #2: ffffffff87c729a0 (rcu_read_lock){....}-{1:2}, at: rcu_lock_acquire include/linux/rcupdate.h:306 [inline] #2: ffffffff87c729a0 (rcu_read_lock){....}-{1:2}, at: rcu_read_lock include/linux/rcupdate.h:747 [inline] #2: ffffffff87c729a0 (rcu_read_lock){....}-{1:2}, at: qdisc_tree_reduce_backlog+0x84/0x580 net/sched/sch_api.c:792 stack backtrace: CPU: 1 PID: 1142 Comm: udevd Not tainted 6.1.74-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/25/2024 Call Trace: <TASK> [<ffffffff85b85f14>] __dump_stack lib/dump_stack.c:88 [inline] [<ffffffff85b85f14>] dump_stack_lvl+0x1b1/0x28f lib/dump_stack.c:106 [<ffffffff85b86007>] dump_stack+0x15/0x1e lib/dump_stack.c:113 [<ffffffff81802299>] lockdep_rcu_suspicious+0x1b9/0x260 kernel/locking/lockdep.c:6592 [<ffffffff84f0054c>] qdisc_lookup+0xac/0x6f0 net/sched/sch_api.c:305 [<ffffffff84f037c3>] qdisc_tree_reduce_backlog+0x243/0x580 net/sched/sch_api.c:811 [<ffffffff84f5b78c>] pfifo_tail_enqueue+0x32c/0x4b0 net/sched/sch_fifo.c:51 [<ffffffff84fbcf63>] qdisc_enqueue include/net/sch_generic.h:833 [inline] [<ffffffff84fbcf63>] netem_dequeue+0xeb3/0x15d0 net/sched/sch_netem.c:723 [<ffffffff84eecab9>] dequeue_skb net/sched/sch_generic.c:292 [inline] [<ffffffff84eecab9>] qdisc_restart net/sched/sch_generic.c:397 [inline] [<ffffffff84eecab9>] __qdisc_run+0x249/0x1e60 net/sched/sch_generic.c:415 [<ffffffff84d7aa96>] qdisc_run+0xd6/0x260 include/net/pkt_sched.h:125 [<ffffffff84d85d29>] net_tx_action+0x7c9/0x970 net/core/dev.c:5313 [<ffffffff85e002bd>] __do_softirq+0x2bd/0x9bd kernel/softirq.c:616 [<ffffffff81568bca>] invoke_softirq kernel/softirq.c:447 [inline] [<ffffffff81568bca>] __irq_exit_rcu+0xca/0x230 kernel/softirq.c:700 [<ffffffff81568ae9>] irq_exit_rcu+0x9/0x20 kernel/softirq.c:712 [<ffffffff85b89f52>] sysvec_apic_timer_interrupt+0x42/0x90 arch/x86/kernel/apic/apic.c:1107 [<ffffffff85c00ccb>] asm_sysvec_apic_timer_interrupt+0x1b/0x20 arch/x86/include/asm/idtentry.h:656

In the Linux kernel, the following vulnerability has been resolved: i2c: stm32f7: Do not prepare/unprepare clock during runtime suspend/resume In case there is any sort of clock controller attached to this I2C bus controller, for example Versaclock or even an AIC32x4 I2C codec, then an I2C transfer triggered from the clock controller clk_ops .prepare callback may trigger a deadlock on drivers/clk/clk.c prepare_lock mutex. This is because the clock controller first grabs the prepare_lock mutex and then performs the prepare operation, including its I2C access. The I2C access resumes this I2C bus controller via .runtime_resume callback, which calls clk_prepare_enable(), which attempts to grab the prepare_lock mutex again and deadlocks. Since the clock are already prepared since probe() and unprepared in remove(), use simple clk_enable()/clk_disable() calls to enable and disable the clock on runtime suspend and resume, to avoid hitting the prepare_lock mutex.

In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: Use request_module_nowait This appears to work around a deadlock regression that came in with the LED merge in 6.9. The deadlock happens on my system with 24 iwlwifi radios, so maybe it something like all worker threads are busy and some work that needs to complete cannot complete. [also remove unnecessary "load_module" var and now-wrong comment]

In the Linux kernel, the following vulnerability has been resolved: dm snapshot: fix lockup in dm_exception_table_exit There was reported lockup when we exit a snapshot with many exceptions. Fix this by adding "cond_resched" to the loop that frees the exceptions.

In the Linux kernel, the following vulnerability has been resolved: stackdepot: fix stack_depot_save_flags() in NMI context Per documentation, stack_depot_save_flags() was meant to be usable from NMI context if STACK_DEPOT_FLAG_CAN_ALLOC is unset. However, it still would try to take the pool_lock in an attempt to save a stack trace in the current pool (if space is available). This could result in deadlock if an NMI is handled while pool_lock is already held. To avoid deadlock, only try to take the lock in NMI context and give up if unsuccessful. The documentation is fixed to clearly convey this.