In the Linux kernel, the following vulnerability has been resolved: netfilter: nft_set_rbtree: fix null deref on element insertion There is no guarantee that rb_prev() will not return NULL in nft_rbtree_gc_elem(): general protection fault, probably for non-canonical address 0xdffffc0000000003: 0000 [#1] PREEMPT SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000018-0x000000000000001f] nft_add_set_elem+0x14b0/0x2990 nf_tables_newsetelem+0x528/0xb30 Furthermore, there is a possible use-after-free while iterating, 'node' can be free'd so we need to cache the next value to use.

In the Linux kernel, the following vulnerability has been resolved: OPP: Fix potential null ptr dereference in dev_pm_opp_get_required_pstate() "opp" pointer is dereferenced before the IS_ERR_OR_NULL() check. Fix it by removing the dereference to cache opp_table and dereference it directly where opp_table is used. This fixes the following smatch warning: drivers/opp/core.c:232 dev_pm_opp_get_required_pstate() warn: variable dereferenced before IS_ERR check 'opp' (see line 230)

In the Linux kernel, the following vulnerability has been resolved: KVM: SVM: Make sure GHCB is mapped before updating Access to the GHCB is mainly in the VMGEXIT path and it is known that the GHCB will be mapped. But there are two paths where it is possible the GHCB might not be mapped. The sev_vcpu_deliver_sipi_vector() routine will update the GHCB to inform the caller of the AP Reset Hold NAE event that a SIPI has been delivered. However, if a SIPI is performed without a corresponding AP Reset Hold, then the GHCB might not be mapped (depending on the previous VMEXIT), which will result in a NULL pointer dereference. The svm_complete_emulated_msr() routine will update the GHCB to inform the caller of a RDMSR/WRMSR operation about any errors. While it is likely that the GHCB will be mapped in this situation, add a safe guard in this path to be certain a NULL pointer dereference is not encountered.

In the Linux kernel, the following vulnerability has been resolved: spi: bcm-qspi: return error if neither hif_mspi nor mspi is available If neither a "hif_mspi" nor "mspi" resource is present, the driver will just early exit in probe but still return success. Apart from not doing anything meaningful, this would then also lead to a null pointer access on removal, as platform_get_drvdata() would return NULL, which it would then try to dereference when trying to unregister the spi master. Fix this by unconditionally calling devm_ioremap_resource(), as it can handle a NULL res and will then return a viable ERR_PTR() if we get one. The "return 0;" was previously a "goto qspi_resource_err;" where then ret was returned, but since ret was still initialized to 0 at this place this was a valid conversion in 63c5395bb7a9 ("spi: bcm-qspi: Fix use-after-free on unbind"). The issue was not introduced by this commit, only made more obvious.

In the Linux kernel, the following vulnerability has been resolved: bcache: Fix __bch_btree_node_alloc to make the failure behavior consistent In some specific situations, the return value of __bch_btree_node_alloc may be NULL. This may lead to a potential NULL pointer dereference in caller function like a calling chain : btree_split->bch_btree_node_alloc->__bch_btree_node_alloc. Fix it by initializing the return value in __bch_btree_node_alloc.

In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Reserve extra IRQ vectors Commit a6dcfe08487e ("scsi: qla2xxx: Limit interrupt vectors to number of CPUs") lowers the number of allocated MSI-X vectors to the number of CPUs. That breaks vector allocation assumptions in qla83xx_iospace_config(), qla24xx_enable_msix() and qla2x00_iospace_config(). Either of the functions computes maximum number of qpairs as: ha->max_qpairs = ha->msix_count - 1 (MB interrupt) - 1 (default response queue) - 1 (ATIO, in dual or pure target mode) max_qpairs is set to zero in case of two CPUs and initiator mode. The number is then used to allocate ha->queue_pair_map inside qla2x00_alloc_queues(). No allocation happens and ha->queue_pair_map is left NULL but the driver thinks there are queue pairs available. qla2xxx_queuecommand() tries to find a qpair in the map and crashes: if (ha->mqenable) { uint32_t tag; uint16_t hwq; struct qla_qpair *qpair = NULL; tag = blk_mq_unique_tag(cmd->request); hwq = blk_mq_unique_tag_to_hwq(tag); qpair = ha->queue_pair_map[hwq]; # <- HERE if (qpair) return qla2xxx_mqueuecommand(host, cmd, qpair); } BUG: kernel NULL pointer dereference, address: 0000000000000000 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 [#1] SMP PTI CPU: 0 PID: 72 Comm: kworker/u4:3 Tainted: G W 5.10.0-rc1+ #25 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.0.0-prebuilt.qemu-project.org 04/01/2014 Workqueue: scsi_wq_7 fc_scsi_scan_rport [scsi_transport_fc] RIP: 0010:qla2xxx_queuecommand+0x16b/0x3f0 [qla2xxx] Call Trace: scsi_queue_rq+0x58c/0xa60 blk_mq_dispatch_rq_list+0x2b7/0x6f0 ? __sbitmap_get_word+0x2a/0x80 __blk_mq_sched_dispatch_requests+0xb8/0x170 blk_mq_sched_dispatch_requests+0x2b/0x50 __blk_mq_run_hw_queue+0x49/0xb0 __blk_mq_delay_run_hw_queue+0xfb/0x150 blk_mq_sched_insert_request+0xbe/0x110 blk_execute_rq+0x45/0x70 __scsi_execute+0x10e/0x250 scsi_probe_and_add_lun+0x228/0xda0 __scsi_scan_target+0xf4/0x620 ? __pm_runtime_resume+0x4f/0x70 scsi_scan_target+0x100/0x110 fc_scsi_scan_rport+0xa1/0xb0 [scsi_transport_fc] process_one_work+0x1ea/0x3b0 worker_thread+0x28/0x3b0 ? process_one_work+0x3b0/0x3b0 kthread+0x112/0x130 ? kthread_park+0x80/0x80 ret_from_fork+0x22/0x30 The driver should allocate enough vectors to provide every CPU it's own HW queue and still handle reserved (MB, RSP, ATIO) interrupts. The change fixes the crash on dual core VM and prevents unbalanced QP allocation where nr_hw_queues is two less than the number of CPUs.

In the Linux kernel, the following vulnerability has been resolved: drm/mediatek: dp: Change logging to dev for mtk_dp_aux_transfer() Change logging from drm_{err,info}() to dev_{err,info}() in functions mtk_dp_aux_transfer() and mtk_dp_aux_do_transfer(): this will be essential to avoid getting NULL pointer kernel panics if any kind of error happens during AUX transfers happening before the bridge is attached. This may potentially start happening in a later commit implementing aux-bus support, as AUX transfers will be triggered from the panel driver (for EDID) before the mtk-dp bridge gets attached, and it's done in preparation for the same.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix potential null dereference The adev->dm.dc pointer can be NULL and dereferenced in amdgpu_dm_fini() without checking. Add a NULL pointer check before calling dc_dmub_srv_destroy(). Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: octeontx2-pf: mcs: Fix NULL pointer dereferences When system is rebooted after creating macsec interface below NULL pointer dereference crashes occurred. This patch fixes those crashes by using correct order of teardown [ 3324.406942] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 [ 3324.415726] Mem abort info: [ 3324.418510] ESR = 0x96000006 [ 3324.421557] EC = 0x25: DABT (current EL), IL = 32 bits [ 3324.426865] SET = 0, FnV = 0 [ 3324.429913] EA = 0, S1PTW = 0 [ 3324.433047] Data abort info: [ 3324.435921] ISV = 0, ISS = 0x00000006 [ 3324.439748] CM = 0, WnR = 0 .... [ 3324.575915] Call trace: [ 3324.578353] cn10k_mdo_del_secy+0x24/0x180 [ 3324.582440] macsec_common_dellink+0xec/0x120 [ 3324.586788] macsec_notify+0x17c/0x1c0 [ 3324.590529] raw_notifier_call_chain+0x50/0x70 [ 3324.594965] call_netdevice_notifiers_info+0x34/0x7c [ 3324.599921] rollback_registered_many+0x354/0x5bc [ 3324.604616] unregister_netdevice_queue+0x88/0x10c [ 3324.609399] unregister_netdev+0x20/0x30 [ 3324.613313] otx2_remove+0x8c/0x310 [ 3324.616794] pci_device_shutdown+0x30/0x70 [ 3324.620882] device_shutdown+0x11c/0x204 [ 966.664930] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 [ 966.673712] Mem abort info: [ 966.676497] ESR = 0x96000006 [ 966.679543] EC = 0x25: DABT (current EL), IL = 32 bits [ 966.684848] SET = 0, FnV = 0 [ 966.687895] EA = 0, S1PTW = 0 [ 966.691028] Data abort info: [ 966.693900] ISV = 0, ISS = 0x00000006 [ 966.697729] CM = 0, WnR = 0 [ 966.833467] Call trace: [ 966.835904] cn10k_mdo_stop+0x20/0xa0 [ 966.839557] macsec_dev_stop+0xe8/0x11c [ 966.843384] __dev_close_many+0xbc/0x140 [ 966.847298] dev_close_many+0x84/0x120 [ 966.851039] rollback_registered_many+0x114/0x5bc [ 966.855735] unregister_netdevice_many.part.0+0x14/0xa0 [ 966.860952] unregister_netdevice_many+0x18/0x24 [ 966.865560] macsec_notify+0x1ac/0x1c0 [ 966.869303] raw_notifier_call_chain+0x50/0x70 [ 966.873738] call_netdevice_notifiers_info+0x34/0x7c [ 966.878694] rollback_registered_many+0x354/0x5bc [ 966.883390] unregister_netdevice_queue+0x88/0x10c [ 966.888173] unregister_netdev+0x20/0x30 [ 966.892090] otx2_remove+0x8c/0x310 [ 966.895571] pci_device_shutdown+0x30/0x70 [ 966.899660] device_shutdown+0x11c/0x204 [ 966.903574] __do_sys_reboot+0x208/0x290 [ 966.907487] __arm64_sys_reboot+0x20/0x30 [ 966.911489] el0_svc_handler+0x80/0x1c0 [ 966.915316] el0_svc+0x8/0x180 [ 966.918362] Code: f9400000 f9400a64 91220014 f94b3403 (f9400060) [ 966.924448] ---[ end trace 341778e799c3d8d7 ]---

In the Linux kernel, the following vulnerability has been resolved: kobject: Add sanity check for kset->kobj.ktype in kset_register() When I register a kset in the following way: static struct kset my_kset; kobject_set_name(&my_kset.kobj, "my_kset"); ret = kset_register(&my_kset); A null pointer dereference exception is occurred: [ 4453.568337] Unable to handle kernel NULL pointer dereference at \ virtual address 0000000000000028 ... ... [ 4453.810361] Call trace: [ 4453.813062] kobject_get_ownership+0xc/0x34 [ 4453.817493] kobject_add_internal+0x98/0x274 [ 4453.822005] kset_register+0x5c/0xb4 [ 4453.825820] my_kobj_init+0x44/0x1000 [my_kset] ... ... Because I didn't initialize my_kset.kobj.ktype. According to the description in Documentation/core-api/kobject.rst: - A ktype is the type of object that embeds a kobject. Every structure that embeds a kobject needs a corresponding ktype. So add sanity check to make sure kset->kobj.ktype is not NULL.

In the Linux kernel, the following vulnerability has been resolved: net/handshake: fix null-ptr-deref in handshake_nl_done_doit() We should not call trace_handshake_cmd_done_err() if socket lookup has failed. Also we should call trace_handshake_cmd_done_err() before releasing the file, otherwise dereferencing sock->sk can return garbage. This also reverts 7afc6d0a107f ("net/handshake: Fix uninitialized local variable") Unable to handle kernel paging request at virtual address dfff800000000003 KASAN: null-ptr-deref in range [0x0000000000000018-0x000000000000001f] Mem abort info: ESR = 0x0000000096000005 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x05: level 1 translation fault Data abort info: ISV = 0, ISS = 0x00000005, ISS2 = 0x00000000 CM = 0, WnR = 0, TnD = 0, TagAccess = 0 GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [dfff800000000003] address between user and kernel address ranges Internal error: Oops: 0000000096000005 [#1] PREEMPT SMP Modules linked in: CPU: 1 PID: 5986 Comm: syz-executor292 Not tainted 6.5.0-rc7-syzkaller-gfe4469582053 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/26/2023 pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : handshake_nl_done_doit+0x198/0x9c8 net/handshake/netlink.c:193 lr : handshake_nl_done_doit+0x180/0x9c8 sp : ffff800096e37180 x29: ffff800096e37200 x28: 1ffff00012dc6e34 x27: dfff800000000000 x26: ffff800096e373d0 x25: 0000000000000000 x24: 00000000ffffffa8 x23: ffff800096e373f0 x22: 1ffff00012dc6e38 x21: 0000000000000000 x20: ffff800096e371c0 x19: 0000000000000018 x18: 0000000000000000 x17: 0000000000000000 x16: ffff800080516cc4 x15: 0000000000000001 x14: 1fffe0001b14aa3b x13: 0000000000000000 x12: 0000000000000000 x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000003 x8 : 0000000000000003 x7 : ffff800080afe47c x6 : 0000000000000000 x5 : 0000000000000000 x4 : 0000000000000000 x3 : ffff800080a88078 x2 : 0000000000000001 x1 : 00000000ffffffa8 x0 : 0000000000000000 Call trace: handshake_nl_done_doit+0x198/0x9c8 net/handshake/netlink.c:193 genl_family_rcv_msg_doit net/netlink/genetlink.c:970 [inline] genl_family_rcv_msg net/netlink/genetlink.c:1050 [inline] genl_rcv_msg+0x96c/0xc50 net/netlink/genetlink.c:1067 netlink_rcv_skb+0x214/0x3c4 net/netlink/af_netlink.c:2549 genl_rcv+0x38/0x50 net/netlink/genetlink.c:1078 netlink_unicast_kernel net/netlink/af_netlink.c:1339 [inline] netlink_unicast+0x660/0x8d4 net/netlink/af_netlink.c:1365 netlink_sendmsg+0x834/0xb18 net/netlink/af_netlink.c:1914 sock_sendmsg_nosec net/socket.c:725 [inline] sock_sendmsg net/socket.c:748 [inline] ____sys_sendmsg+0x56c/0x840 net/socket.c:2494 ___sys_sendmsg net/socket.c:2548 [inline] __sys_sendmsg+0x26c/0x33c net/socket.c:2577 __do_sys_sendmsg net/socket.c:2586 [inline] __se_sys_sendmsg net/socket.c:2584 [inline] __arm64_sys_sendmsg+0x80/0x94 net/socket.c:2584 __invoke_syscall arch/arm64/kernel/syscall.c:37 [inline] invoke_syscall+0x98/0x2b8 arch/arm64/kernel/syscall.c:51 el0_svc_common+0x130/0x23c arch/arm64/kernel/syscall.c:136 do_el0_svc+0x48/0x58 arch/arm64/kernel/syscall.c:155 el0_svc+0x58/0x16c arch/arm64/kernel/entry-common.c:678 el0t_64_sync_handler+0x84/0xfc arch/arm64/kernel/entry-common.c:696 el0t_64_sync+0x190/0x194 arch/arm64/kernel/entry.S:591 Code: 12800108 b90043e8 910062b3 d343fe68 (387b6908)

In the Linux kernel, the following vulnerability has been resolved: drm/ttm: check null pointer before accessing when swapping Add a check to avoid null pointer dereference as below: [ 90.002283] general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN NOPTI [ 90.002292] KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] [ 90.002346] ? exc_general_protection+0x159/0x240 [ 90.002352] ? asm_exc_general_protection+0x26/0x30 [ 90.002357] ? ttm_bo_evict_swapout_allowable+0x322/0x5e0 [ttm] [ 90.002365] ? ttm_bo_evict_swapout_allowable+0x42e/0x5e0 [ttm] [ 90.002373] ttm_bo_swapout+0x134/0x7f0 [ttm] [ 90.002383] ? __pfx_ttm_bo_swapout+0x10/0x10 [ttm] [ 90.002391] ? lock_acquire+0x44d/0x4f0 [ 90.002398] ? ttm_device_swapout+0xa5/0x260 [ttm] [ 90.002412] ? lock_acquired+0x355/0xa00 [ 90.002416] ? do_raw_spin_trylock+0xb6/0x190 [ 90.002421] ? __pfx_lock_acquired+0x10/0x10 [ 90.002426] ? ttm_global_swapout+0x25/0x210 [ttm] [ 90.002442] ttm_device_swapout+0x198/0x260 [ttm] [ 90.002456] ? __pfx_ttm_device_swapout+0x10/0x10 [ttm] [ 90.002472] ttm_global_swapout+0x75/0x210 [ttm] [ 90.002486] ttm_tt_populate+0x187/0x3f0 [ttm] [ 90.002501] ttm_bo_handle_move_mem+0x437/0x590 [ttm] [ 90.002517] ttm_bo_validate+0x275/0x430 [ttm] [ 90.002530] ? __pfx_ttm_bo_validate+0x10/0x10 [ttm] [ 90.002544] ? kasan_save_stack+0x33/0x60 [ 90.002550] ? kasan_set_track+0x25/0x30 [ 90.002554] ? __kasan_kmalloc+0x8f/0xa0 [ 90.002558] ? amdgpu_gtt_mgr_new+0x81/0x420 [amdgpu] [ 90.003023] ? ttm_resource_alloc+0xf6/0x220 [ttm] [ 90.003038] amdgpu_bo_pin_restricted+0x2dd/0x8b0 [amdgpu] [ 90.003210] ? __x64_sys_ioctl+0x131/0x1a0 [ 90.003210] ? do_syscall_64+0x60/0x90

In the Linux kernel, the following vulnerability has been resolved: ice: xsk: disable txq irq before flushing hw ice_qp_dis() intends to stop a given queue pair that is a target of xsk pool attach/detach. One of the steps is to disable interrupts on these queues. It currently is broken in a way that txq irq is turned off *after* HW flush which in turn takes no effect. ice_qp_dis(): -> ice_qvec_dis_irq() --> disable rxq irq --> flush hw -> ice_vsi_stop_tx_ring() -->disable txq irq Below splat can be triggered by following steps: - start xdpsock WITHOUT loading xdp prog - run xdp_rxq_info with XDP_TX action on this interface - start traffic - terminate xdpsock [ 256.312485] BUG: kernel NULL pointer dereference, address: 0000000000000018 [ 256.319560] #PF: supervisor read access in kernel mode [ 256.324775] #PF: error_code(0x0000) - not-present page [ 256.329994] PGD 0 P4D 0 [ 256.332574] Oops: 0000 [#1] PREEMPT SMP NOPTI [ 256.337006] CPU: 3 PID: 32 Comm: ksoftirqd/3 Tainted: G OE 6.2.0-rc5+ #51 [ 256.345218] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0008.031920191559 03/19/2019 [ 256.355807] RIP: 0010:ice_clean_rx_irq_zc+0x9c/0x7d0 [ice] [ 256.361423] Code: b7 8f 8a 00 00 00 66 39 ca 0f 84 f1 04 00 00 49 8b 47 40 4c 8b 24 d0 41 0f b7 45 04 66 25 ff 3f 66 89 04 24 0f 84 85 02 00 00 <49> 8b 44 24 18 0f b7 14 24 48 05 00 01 00 00 49 89 04 24 49 89 44 [ 256.380463] RSP: 0018:ffffc900088bfd20 EFLAGS: 00010206 [ 256.385765] RAX: 000000000000003c RBX: 0000000000000035 RCX: 000000000000067f [ 256.393012] RDX: 0000000000000775 RSI: 0000000000000000 RDI: ffff8881deb3ac80 [ 256.400256] RBP: 000000000000003c R08: ffff889847982710 R09: 0000000000010000 [ 256.407500] R10: ffffffff82c060c0 R11: 0000000000000004 R12: 0000000000000000 [ 256.414746] R13: ffff88811165eea0 R14: ffffc9000d255000 R15: ffff888119b37600 [ 256.421990] FS: 0000000000000000(0000) GS:ffff8897e0cc0000(0000) knlGS:0000000000000000 [ 256.430207] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 256.436036] CR2: 0000000000000018 CR3: 0000000005c0a006 CR4: 00000000007706e0 [ 256.443283] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 256.450527] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 256.457770] PKRU: 55555554 [ 256.460529] Call Trace: [ 256.463015] <TASK> [ 256.465157] ? ice_xmit_zc+0x6e/0x150 [ice] [ 256.469437] ice_napi_poll+0x46d/0x680 [ice] [ 256.473815] ? _raw_spin_unlock_irqrestore+0x1b/0x40 [ 256.478863] __napi_poll+0x29/0x160 [ 256.482409] net_rx_action+0x136/0x260 [ 256.486222] __do_softirq+0xe8/0x2e5 [ 256.489853] ? smpboot_thread_fn+0x2c/0x270 [ 256.494108] run_ksoftirqd+0x2a/0x50 [ 256.497747] smpboot_thread_fn+0x1c1/0x270 [ 256.501907] ? __pfx_smpboot_thread_fn+0x10/0x10 [ 256.506594] kthread+0xea/0x120 [ 256.509785] ? __pfx_kthread+0x10/0x10 [ 256.513597] ret_from_fork+0x29/0x50 [ 256.517238] </TASK> In fact, irqs were not disabled and napi managed to be scheduled and run while xsk_pool pointer was still valid, but SW ring of xdp_buff pointers was already freed. To fix this, call ice_qvec_dis_irq() after ice_vsi_stop_tx_ring(). Also while at it, remove redundant ice_clean_rx_ring() call - this is handled in ice_qp_clean_rings().

In the Linux kernel, the following vulnerability has been resolved: xfrm: add NULL check in xfrm_update_ae_params Normally, x->replay_esn and x->preplay_esn should be allocated at xfrm_alloc_replay_state_esn(...) in xfrm_state_construct(...), hence the xfrm_update_ae_params(...) is okay to update them. However, the current implementation of xfrm_new_ae(...) allows a malicious user to directly dereference a NULL pointer and crash the kernel like below. BUG: kernel NULL pointer dereference, address: 0000000000000000 PGD 8253067 P4D 8253067 PUD 8e0e067 PMD 0 Oops: 0002 [#1] PREEMPT SMP KASAN NOPTI CPU: 0 PID: 98 Comm: poc.npd Not tainted 6.4.0-rc7-00072-gdad9774deaf1 #8 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.o4 RIP: 0010:memcpy_orig+0xad/0x140 Code: e8 4c 89 5f e0 48 8d 7f e0 73 d2 83 c2 20 48 29 d6 48 29 d7 83 fa 10 72 34 4c 8b 06 4c 8b 4e 08 c RSP: 0018:ffff888008f57658 EFLAGS: 00000202 RAX: 0000000000000000 RBX: ffff888008bd0000 RCX: ffffffff8238e571 RDX: 0000000000000018 RSI: ffff888007f64844 RDI: 0000000000000000 RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: ffff888008f57818 R13: ffff888007f64aa4 R14: 0000000000000000 R15: 0000000000000000 FS: 00000000014013c0(0000) GS:ffff88806d600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 00000000054d8000 CR4: 00000000000006f0 Call Trace: <TASK> ? __die+0x1f/0x70 ? page_fault_oops+0x1e8/0x500 ? __pfx_is_prefetch.constprop.0+0x10/0x10 ? __pfx_page_fault_oops+0x10/0x10 ? _raw_spin_unlock_irqrestore+0x11/0x40 ? fixup_exception+0x36/0x460 ? _raw_spin_unlock_irqrestore+0x11/0x40 ? exc_page_fault+0x5e/0xc0 ? asm_exc_page_fault+0x26/0x30 ? xfrm_update_ae_params+0xd1/0x260 ? memcpy_orig+0xad/0x140 ? __pfx__raw_spin_lock_bh+0x10/0x10 xfrm_update_ae_params+0xe7/0x260 xfrm_new_ae+0x298/0x4e0 ? __pfx_xfrm_new_ae+0x10/0x10 ? __pfx_xfrm_new_ae+0x10/0x10 xfrm_user_rcv_msg+0x25a/0x410 ? __pfx_xfrm_user_rcv_msg+0x10/0x10 ? __alloc_skb+0xcf/0x210 ? stack_trace_save+0x90/0xd0 ? filter_irq_stacks+0x1c/0x70 ? __stack_depot_save+0x39/0x4e0 ? __kasan_slab_free+0x10a/0x190 ? kmem_cache_free+0x9c/0x340 ? netlink_recvmsg+0x23c/0x660 ? sock_recvmsg+0xeb/0xf0 ? __sys_recvfrom+0x13c/0x1f0 ? __x64_sys_recvfrom+0x71/0x90 ? do_syscall_64+0x3f/0x90 ? entry_SYSCALL_64_after_hwframe+0x72/0xdc ? copyout+0x3e/0x50 netlink_rcv_skb+0xd6/0x210 ? __pfx_xfrm_user_rcv_msg+0x10/0x10 ? __pfx_netlink_rcv_skb+0x10/0x10 ? __pfx_sock_has_perm+0x10/0x10 ? mutex_lock+0x8d/0xe0 ? __pfx_mutex_lock+0x10/0x10 xfrm_netlink_rcv+0x44/0x50 netlink_unicast+0x36f/0x4c0 ? __pfx_netlink_unicast+0x10/0x10 ? netlink_recvmsg+0x500/0x660 netlink_sendmsg+0x3b7/0x700 This Null-ptr-deref bug is assigned CVE-2023-3772. And this commit adds additional NULL check in xfrm_update_ae_params to fix the NPD.

In the Linux kernel, the following vulnerability has been resolved: spi: spi-zynq-qspi: Fix a NULL pointer dereference in zynq_qspi_exec_mem_op() In zynq_qspi_exec_mem_op(), kzalloc() is directly used in memset(), which could lead to a NULL pointer dereference on failure of kzalloc(). Fix this bug by adding a check of tmpbuf. This bug was found by a static analyzer. The analysis employs differential checking to identify inconsistent security operations (e.g., checks or kfrees) between two code paths and confirms that the inconsistent operations are not recovered in the current function or the callers, so they constitute bugs. Note that, as a bug found by static analysis, it can be a false positive or hard to trigger. Multiple researchers have cross-reviewed the bug. Builds with CONFIG_SPI_ZYNQ_QSPI=m show no new warnings, and our static analyzer no longer warns about this code.

In the Linux kernel, the following vulnerability has been resolved: tracing: Fix null pointer dereference in tracing_err_log_open() Fix an issue in function 'tracing_err_log_open'. The function doesn't call 'seq_open' if the file is opened only with write permissions, which results in 'file->private_data' being left as null. If we then use 'lseek' on that opened file, 'seq_lseek' dereferences 'file->private_data' in 'mutex_lock(&m->lock)', resulting in a kernel panic. Writing to this node requires root privileges, therefore this bug has very little security impact. Tracefs node: /sys/kernel/tracing/error_log Example Kernel panic: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000038 Call trace: mutex_lock+0x30/0x110 seq_lseek+0x34/0xb8 __arm64_sys_lseek+0x6c/0xb8 invoke_syscall+0x58/0x13c el0_svc_common+0xc4/0x10c do_el0_svc+0x24/0x98 el0_svc+0x24/0x88 el0t_64_sync_handler+0x84/0xe4 el0t_64_sync+0x1b4/0x1b8 Code: d503201f aa0803e0 aa1f03e1 aa0103e9 (c8e97d02) ---[ end trace 561d1b49c12cf8a5 ]--- Kernel panic - not syncing: Oops: Fatal exception

In the Linux kernel, the following vulnerability has been resolved: thermal: core: Fix NULL pointer dereference in zone registration error path If device_register() in thermal_zone_device_register_with_trips() returns an error, the tz variable is set to NULL and subsequently dereferenced in kfree(tz->tzp). Commit adc8749b150c ("thermal/drivers/core: Use put_device() if device_register() fails") added the tz = NULL assignment in question to avoid a possible double-free after dropping the reference to the zone device. However, after commit 4649620d9404 ("thermal: core: Make thermal_zone_device_unregister() return after freeing the zone"), that assignment has become redundant, because dropping the reference to the zone device does not cause the zone object to be freed any more. Drop it to address the NULL pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: i915/perf: Fix NULL deref bugs with drm_dbg() calls When i915 perf interface is not available dereferencing it will lead to NULL dereferences. As returning -ENOTSUPP is pretty clear return when perf interface is not available. [tursulin: added stable tag] (cherry picked from commit 36f27350ff745bd228ab04d7845dfbffc177a889)

In the Linux kernel, the following vulnerability has been resolved: tracing: Have trace_event_file have ref counters The following can crash the kernel: # cd /sys/kernel/tracing # echo 'p:sched schedule' > kprobe_events # exec 5>>events/kprobes/sched/enable # > kprobe_events # exec 5>&- The above commands: 1. Change directory to the tracefs directory 2. Create a kprobe event (doesn't matter what one) 3. Open bash file descriptor 5 on the enable file of the kprobe event 4. Delete the kprobe event (removes the files too) 5. Close the bash file descriptor 5 The above causes a crash! BUG: kernel NULL pointer dereference, address: 0000000000000028 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 6 PID: 877 Comm: bash Not tainted 6.5.0-rc4-test-00008-g2c6b6b1029d4-dirty #186 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-debian-1.16.2-1 04/01/2014 RIP: 0010:tracing_release_file_tr+0xc/0x50 What happens here is that the kprobe event creates a trace_event_file "file" descriptor that represents the file in tracefs to the event. It maintains state of the event (is it enabled for the given instance?). Opening the "enable" file gets a reference to the event "file" descriptor via the open file descriptor. When the kprobe event is deleted, the file is also deleted from the tracefs system which also frees the event "file" descriptor. But as the tracefs file is still opened by user space, it will not be totally removed until the final dput() is called on it. But this is not true with the event "file" descriptor that is already freed. If the user does a write to or simply closes the file descriptor it will reference the event "file" descriptor that was just freed, causing a use-after-free bug. To solve this, add a ref count to the event "file" descriptor as well as a new flag called "FREED". The "file" will not be freed until the last reference is released. But the FREE flag will be set when the event is removed to prevent any more modifications to that event from happening, even if there's still a reference to the event "file" descriptor.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Fix potential null pointer derefernce The amdgpu_ras_get_context may return NULL if device not support ras feature, so add check before using.

In the Linux kernel, the following vulnerability has been resolved: drm/bridge: lt8912b: Fix crash on bridge detach The lt8912b driver, in its bridge detach function, calls drm_connector_unregister() and drm_connector_cleanup(). drm_connector_unregister() should be called only for connectors explicitly registered with drm_connector_register(), which is not the case in lt8912b. The driver's drm_connector_funcs.destroy hook is set to drm_connector_cleanup(). Thus the driver should not call either drm_connector_unregister() nor drm_connector_cleanup() in its lt8912_bridge_detach(), as they cause a crash on bridge detach: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 Mem abort info: ESR = 0x0000000096000006 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x06: level 2 translation fault Data abort info: ISV = 0, ISS = 0x00000006, ISS2 = 0x00000000 CM = 0, WnR = 0, TnD = 0, TagAccess = 0 GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 user pgtable: 4k pages, 48-bit VAs, pgdp=00000000858f3000 [0000000000000000] pgd=0800000085918003, p4d=0800000085918003, pud=0800000085431003, pmd=0000000000000000 Internal error: Oops: 0000000096000006 [#1] PREEMPT SMP Modules linked in: tidss(-) display_connector lontium_lt8912b tc358768 panel_lvds panel_simple drm_dma_helper drm_kms_helper drm drm_panel_orientation_quirks CPU: 3 PID: 462 Comm: rmmod Tainted: G W 6.5.0-rc2+ #2 Hardware name: Toradex Verdin AM62 on Verdin Development Board (DT) pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : drm_connector_cleanup+0x78/0x2d4 [drm] lr : lt8912_bridge_detach+0x54/0x6c [lontium_lt8912b] sp : ffff800082ed3a90 x29: ffff800082ed3a90 x28: ffff0000040c1940 x27: 0000000000000000 x26: 0000000000000000 x25: dead000000000122 x24: dead000000000122 x23: dead000000000100 x22: ffff000003fb6388 x21: 0000000000000000 x20: 0000000000000000 x19: ffff000003fb6260 x18: fffffffffffe56e8 x17: 0000000000000000 x16: 0010000000000000 x15: 0000000000000038 x14: 0000000000000000 x13: ffff800081914b48 x12: 000000000000040e x11: 000000000000015a x10: ffff80008196ebb8 x9 : ffff800081914b48 x8 : 00000000ffffefff x7 : ffff0000040c1940 x6 : ffff80007aa649d0 x5 : 0000000000000000 x4 : 0000000000000001 x3 : ffff80008159e008 x2 : 0000000000000000 x1 : 0000000000000000 x0 : 0000000000000000 Call trace: drm_connector_cleanup+0x78/0x2d4 [drm] lt8912_bridge_detach+0x54/0x6c [lontium_lt8912b] drm_bridge_detach+0x44/0x84 [drm] drm_encoder_cleanup+0x40/0xb8 [drm] drmm_encoder_alloc_release+0x1c/0x30 [drm] drm_managed_release+0xac/0x148 [drm] drm_dev_put.part.0+0x88/0xb8 [drm] devm_drm_dev_init_release+0x14/0x24 [drm] devm_action_release+0x14/0x20 release_nodes+0x5c/0x90 devres_release_all+0x8c/0xe0 device_unbind_cleanup+0x18/0x68 device_release_driver_internal+0x208/0x23c driver_detach+0x4c/0x94 bus_remove_driver+0x70/0xf4 driver_unregister+0x30/0x60 platform_driver_unregister+0x14/0x20 tidss_platform_driver_exit+0x18/0xb2c [tidss] __arm64_sys_delete_module+0x1a0/0x2b4 invoke_syscall+0x48/0x110 el0_svc_common.constprop.0+0x60/0x10c do_el0_svc_compat+0x1c/0x40 el0_svc_compat+0x40/0xac el0t_32_sync_handler+0xb0/0x138 el0t_32_sync+0x194/0x198 Code: 9104a276 f2fbd5b7 aa0203e1 91008af8 (f85c0420)

In the Linux kernel, the following vulnerability has been resolved: HID: betop: check shape of output reports betopff_init() only checks the total sum of the report counts for each report field to be at least 4, but hid_betopff_play() expects 4 report fields. A device advertising an output report with one field and 4 report counts would pass the check but crash the kernel with a NULL pointer dereference in hid_betopff_play().

In the Linux kernel, the following vulnerability has been resolved: drm/msm/dpu: check for null return of devm_kzalloc() in dpu_writeback_init() Because of the possilble failure of devm_kzalloc(), dpu_wb_conn might be NULL and will cause null pointer dereference later. Therefore, it might be better to check it and directly return -ENOMEM. Patchwork: https://patchwork.freedesktop.org/patch/512277/ [DB: fixed typo in commit message]

In the Linux kernel, the following vulnerability has been resolved: Revert "tty: n_gsm: fix UAF in gsm_cleanup_mux" This reverts commit 9b9c8195f3f0d74a826077fc1c01b9ee74907239. The commit above is reverted as it did not solve the original issue. gsm_cleanup_mux() tries to free up the virtual ttys by calling gsm_dlci_release() for each available DLCI. There, dlci_put() is called to decrease the reference counter for the DLCI via tty_port_put() which finally calls gsm_dlci_free(). This already clears the pointer which is being checked in gsm_cleanup_mux() before calling gsm_dlci_release(). Therefore, it is not necessary to clear this pointer in gsm_cleanup_mux() as done in the reverted commit. The commit introduces a null pointer dereference: <TASK> ? __die+0x1f/0x70 ? page_fault_oops+0x156/0x420 ? search_exception_tables+0x37/0x50 ? fixup_exception+0x21/0x310 ? exc_page_fault+0x69/0x150 ? asm_exc_page_fault+0x26/0x30 ? tty_port_put+0x19/0xa0 gsmtty_cleanup+0x29/0x80 [n_gsm] release_one_tty+0x37/0xe0 process_one_work+0x1e6/0x3e0 worker_thread+0x4c/0x3d0 ? __pfx_worker_thread+0x10/0x10 kthread+0xe1/0x110 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2f/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1b/0x30 </TASK> The actual issue is that nothing guards dlci_put() from being called multiple times while the tty driver was triggered but did not yet finished calling gsm_dlci_free().

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix cleanup null-ptr deref on encap lock During module is unloaded while a peer tc flow is still offloaded, first the peer uplink rep profile is changed to a nic profile, and so neigh encap lock is destroyed. Next during unload, the VF reps netdevs are unregistered which causes the original non-peer tc flow to be deleted, which deletes the peer flow. The peer flow deletion detaches the encap entry and try to take the already destroyed encap lock, causing the below trace. Fix this by clearing peer flows during tc eswitch cleanup (mlx5e_tc_esw_cleanup()). Relevant trace: [ 4316.837128] BUG: kernel NULL pointer dereference, address: 00000000000001d8 [ 4316.842239] RIP: 0010:__mutex_lock+0xb5/0xc40 [ 4316.851897] Call Trace: [ 4316.852481] <TASK> [ 4316.857214] mlx5e_rep_neigh_entry_release+0x93/0x790 [mlx5_core] [ 4316.858258] mlx5e_rep_encap_entry_detach+0xa7/0xf0 [mlx5_core] [ 4316.859134] mlx5e_encap_dealloc+0xa3/0xf0 [mlx5_core] [ 4316.859867] clean_encap_dests.part.0+0x5c/0xe0 [mlx5_core] [ 4316.860605] mlx5e_tc_del_fdb_flow+0x32a/0x810 [mlx5_core] [ 4316.862609] __mlx5e_tc_del_fdb_peer_flow+0x1a2/0x250 [mlx5_core] [ 4316.863394] mlx5e_tc_del_flow+0x(/0x630 [mlx5_core] [ 4316.864090] mlx5e_flow_put+0x5f/0x100 [mlx5_core] [ 4316.864771] mlx5e_delete_flower+0x4de/0xa40 [mlx5_core] [ 4316.865486] tc_setup_cb_reoffload+0x20/0x80 [ 4316.865905] fl_reoffload+0x47c/0x510 [cls_flower] [ 4316.869181] tcf_block_playback_offloads+0x91/0x1d0 [ 4316.869649] tcf_block_unbind+0xe7/0x1b0 [ 4316.870049] tcf_block_offload_cmd.isra.0+0x1ee/0x270 [ 4316.879266] tcf_block_offload_unbind+0x61/0xa0 [ 4316.879711] __tcf_block_put+0xa4/0x310

In the Linux kernel, the following vulnerability has been resolved: raw: Fix NULL deref in raw_get_next(). Dae R. Jeong reported a NULL deref in raw_get_next() [0]. It seems that the repro was running these sequences in parallel so that one thread was iterating on a socket that was being freed in another netns. unshare(0x40060200) r0 = syz_open_procfs(0x0, &(0x7f0000002080)='net/raw\x00') socket$inet_icmp_raw(0x2, 0x3, 0x1) pread64(r0, &(0x7f0000000000)=""/10, 0xa, 0x10000000007f) After commit 0daf07e52709 ("raw: convert raw sockets to RCU"), we use RCU and hlist_nulls_for_each_entry() to iterate over SOCK_RAW sockets. However, we should use spinlock for slow paths to avoid the NULL deref. Also, SOCK_RAW does not use SLAB_TYPESAFE_BY_RCU, and the slab object is not reused during iteration in the grace period. In fact, the lockless readers do not check the nulls marker with get_nulls_value(). So, SOCK_RAW should use hlist instead of hlist_nulls. Instead of adding an unnecessary barrier by sk_nulls_for_each_rcu(), let's convert hlist_nulls to hlist and use sk_for_each_rcu() for fast paths and sk_for_each() and spinlock for /proc/net/raw. [0]: general protection fault, probably for non-canonical address 0xdffffc0000000005: 0000 [#1] PREEMPT SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000028-0x000000000000002f] CPU: 2 PID: 20952 Comm: syz-executor.0 Not tainted 6.2.0-g048ec869bafd-dirty #7 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 RIP: 0010:read_pnet include/net/net_namespace.h:383 [inline] RIP: 0010:sock_net include/net/sock.h:649 [inline] RIP: 0010:raw_get_next net/ipv4/raw.c:974 [inline] RIP: 0010:raw_get_idx net/ipv4/raw.c:986 [inline] RIP: 0010:raw_seq_start+0x431/0x800 net/ipv4/raw.c:995 Code: ef e8 33 3d 94 f7 49 8b 6d 00 4c 89 ef e8 b7 65 5f f7 49 89 ed 49 83 c5 98 0f 84 9a 00 00 00 48 83 c5 c8 48 89 e8 48 c1 e8 03 <42> 80 3c 30 00 74 08 48 89 ef e8 00 3d 94 f7 4c 8b 7d 00 48 89 ef RSP: 0018:ffffc9001154f9b0 EFLAGS: 00010206 RAX: 0000000000000005 RBX: 1ffff1100302c8fd RCX: 0000000000000000 RDX: 0000000000000028 RSI: ffffc9001154f988 RDI: ffffc9000f77a338 RBP: 0000000000000029 R08: ffffffff8a50ffb4 R09: fffffbfff24b6bd9 R10: fffffbfff24b6bd9 R11: 0000000000000000 R12: ffff88801db73b78 R13: fffffffffffffff9 R14: dffffc0000000000 R15: 0000000000000030 FS: 00007f843ae8e700(0000) GS:ffff888063700000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000055bb9614b35f CR3: 000000003c672000 CR4: 00000000003506e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> seq_read_iter+0x4c6/0x10f0 fs/seq_file.c:225 seq_read+0x224/0x320 fs/seq_file.c:162 pde_read fs/proc/inode.c:316 [inline] proc_reg_read+0x23f/0x330 fs/proc/inode.c:328 vfs_read+0x31e/0xd30 fs/read_write.c:468 ksys_pread64 fs/read_write.c:665 [inline] __do_sys_pread64 fs/read_write.c:675 [inline] __se_sys_pread64 fs/read_write.c:672 [inline] __x64_sys_pread64+0x1e9/0x280 fs/read_write.c:672 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x4e/0xa0 arch/x86/entry/common.c:82 entry_SYSCALL_64_after_hwframe+0x63/0xcd RIP: 0033:0x478d29 Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f843ae8dbe8 EFLAGS: 00000246 ORIG_RAX: 0000000000000011 RAX: ffffffffffffffda RBX: 0000000000791408 RCX: 0000000000478d29 RDX: 000000000000000a RSI: 0000000020000000 RDI: 0000000000000003 RBP: 00000000f477909a R08: 0000000000000000 R09: 0000000000000000 R10: 000010000000007f R11: 0000000000000246 R12: 0000000000791740 R13: 0000000000791414 R14: 0000000000791408 R15: 00007ffc2eb48a50 </TASK> Modules linked in: ---[ end trace 0000000000000000 ]--- RIP: 0010 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Synchronize the IOCB count to be in order A system hang was observed with the following call trace: BUG: kernel NULL pointer dereference, address: 0000000000000000 PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 15 PID: 86747 Comm: nvme Kdump: loaded Not tainted 6.2.0+ #1 Hardware name: Dell Inc. PowerEdge R6515/04F3CJ, BIOS 2.7.3 03/31/2022 RIP: 0010:__wake_up_common+0x55/0x190 Code: 41 f6 01 04 0f 85 b2 00 00 00 48 8b 43 08 4c 8d 40 e8 48 8d 43 08 48 89 04 24 48 89 c6\ 49 8d 40 18 48 39 c6 0f 84 e9 00 00 00 <49> 8b 40 18 89 6c 24 14 31 ed 4c 8d 60 e8 41 8b 18 f6 c3 04 75 5d RSP: 0018:ffffb05a82afbba0 EFLAGS: 00010082 RAX: 0000000000000000 RBX: ffff8f9b83a00018 RCX: 0000000000000000 RDX: 0000000000000001 RSI: ffff8f9b83a00020 RDI: ffff8f9b83a00018 RBP: 0000000000000001 R08: ffffffffffffffe8 R09: ffffb05a82afbbf8 R10: 70735f7472617473 R11: 5f30307832616c71 R12: 0000000000000001 R13: 0000000000000003 R14: 0000000000000000 R15: 0000000000000000 FS: 00007f815cf4c740(0000) GS:ffff8f9eeed80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 000000010633a000 CR4: 0000000000350ee0 Call Trace: <TASK> __wake_up_common_lock+0x83/0xd0 qla_nvme_ls_req+0x21b/0x2b0 [qla2xxx] __nvme_fc_send_ls_req+0x1b5/0x350 [nvme_fc] nvme_fc_xmt_disconnect_assoc+0xca/0x110 [nvme_fc] nvme_fc_delete_association+0x1bf/0x220 [nvme_fc] ? nvme_remove_namespaces+0x9f/0x140 [nvme_core] nvme_do_delete_ctrl+0x5b/0xa0 [nvme_core] nvme_sysfs_delete+0x5f/0x70 [nvme_core] kernfs_fop_write_iter+0x12b/0x1c0 vfs_write+0x2a3/0x3b0 ksys_write+0x5f/0xe0 do_syscall_64+0x5c/0x90 ? syscall_exit_work+0x103/0x130 ? syscall_exit_to_user_mode+0x12/0x30 ? do_syscall_64+0x69/0x90 ? exit_to_user_mode_loop+0xd0/0x130 ? exit_to_user_mode_prepare+0xec/0x100 ? syscall_exit_to_user_mode+0x12/0x30 ? do_syscall_64+0x69/0x90 ? syscall_exit_to_user_mode+0x12/0x30 ? do_syscall_64+0x69/0x90 entry_SYSCALL_64_after_hwframe+0x72/0xdc RIP: 0033:0x7f815cd3eb97 The IOCB counts are out of order and that would block any commands from going out and subsequently hang the system. Synchronize the IOCB count to be in correct order.

In the Linux kernel, the following vulnerability has been resolved: hid: cp2112: Fix duplicate workqueue initialization Previously the cp2112 driver called INIT_DELAYED_WORK within cp2112_gpio_irq_startup, resulting in duplicate initilizations of the workqueue on subsequent IRQ startups following an initial request. This resulted in a warning in set_work_data in workqueue.c, as well as a rare NULL dereference within process_one_work in workqueue.c. Initialize the workqueue within _probe instead.

In the Linux kernel, the following vulnerability has been resolved: drm/tegra: dsi: Add missing check for of_find_device_by_node Add check for the return value of of_find_device_by_node() and return the error if it fails in order to avoid NULL pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix NULL pointer dereference at hibernate During hibernate sequence the source context might not have a clk_mgr. So don't use it to look for DML2 support.

In the Linux kernel, the following vulnerability has been resolved: net: stmmac: enable all safety features by default In the original implementation of dwmac5 commit 8bf993a5877e ("net: stmmac: Add support for DWMAC5 and implement Safety Features") all safety features were enabled by default. Later it seems some implementations didn't have support for all the features, so in commit 5ac712dcdfef ("net: stmmac: enable platform specific safety features") the safety_feat_cfg structure was added to the callback and defined for some platforms to selectively enable these safety features. The problem is that only certain platforms were given that software support. If the automotive safety package bit is set in the hardware features register the safety feature callback is called for the platform, and for platforms that didn't get a safety_feat_cfg defined this results in the following NULL pointer dereference: [ 7.933303] Call trace: [ 7.935812] dwmac5_safety_feat_config+0x20/0x170 [stmmac] [ 7.941455] __stmmac_open+0x16c/0x474 [stmmac] [ 7.946117] stmmac_open+0x38/0x70 [stmmac] [ 7.950414] __dev_open+0x100/0x1dc [ 7.954006] __dev_change_flags+0x18c/0x204 [ 7.958297] dev_change_flags+0x24/0x6c [ 7.962237] do_setlink+0x2b8/0xfa4 [ 7.965827] __rtnl_newlink+0x4ec/0x840 [ 7.969766] rtnl_newlink+0x50/0x80 [ 7.973353] rtnetlink_rcv_msg+0x12c/0x374 [ 7.977557] netlink_rcv_skb+0x5c/0x130 [ 7.981500] rtnetlink_rcv+0x18/0x2c [ 7.985172] netlink_unicast+0x2e8/0x340 [ 7.989197] netlink_sendmsg+0x1a8/0x420 [ 7.993222] ____sys_sendmsg+0x218/0x280 [ 7.997249] ___sys_sendmsg+0xac/0x100 [ 8.001103] __sys_sendmsg+0x84/0xe0 [ 8.004776] __arm64_sys_sendmsg+0x24/0x30 [ 8.008983] invoke_syscall+0x48/0x114 [ 8.012840] el0_svc_common.constprop.0+0xcc/0xec [ 8.017665] do_el0_svc+0x38/0xb0 [ 8.021071] el0_svc+0x2c/0x84 [ 8.024212] el0t_64_sync_handler+0xf4/0x120 [ 8.028598] el0t_64_sync+0x190/0x194 Go back to the original behavior, if the automotive safety package is found to be supported in hardware enable all the features unless safety_feat_cfg is passed in saying this particular platform only supports a subset of the features.

In the Linux kernel, the following vulnerability has been resolved: aio: fix mremap after fork null-deref Commit e4a0d3e720e7 ("aio: Make it possible to remap aio ring") introduced a null-deref if mremap is called on an old aio mapping after fork as mm->ioctx_table will be set to NULL. [jmoyer@redhat.com: fix 80 column issue]

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: do not run mt76_unregister_device() on unregistered hw Trying to probe a mt7921e pci card without firmware results in a successful probe where ieee80211_register_hw hasn't been called. When removing the driver, ieee802111_unregister_hw is called unconditionally leading to a kernel NULL pointer dereference. Fix the issue running mt76_unregister_device routine just for registered hw.

In the Linux kernel, the following vulnerability has been resolved: netfilter: nft_set_rbtree: fix overlap expiration walk The lazy gc on insert that should remove timed-out entries fails to release the other half of the interval, if any. Can be reproduced with tests/shell/testcases/sets/0044interval_overlap_0 in nftables.git and kmemleak enabled kernel. Second bug is the use of rbe_prev vs. prev pointer. If rbe_prev() returns NULL after at least one iteration, rbe_prev points to element that is not an end interval, hence it should not be removed. Lastly, check the genmask of the end interval if this is active in the current generation.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Check writeback connectors in create_validate_stream_for_sink [WHY & HOW] This is to check connector type to avoid unhandled null pointer for writeback connectors.

In the Linux kernel, the following vulnerability has been resolved: drm/ttm: Fix a NULL pointer dereference The LRU mechanism may look up a resource in the process of being removed from an object. The locking rules here are a bit unclear but it looks currently like res->bo assignment is protected by the LRU lock, whereas bo->resource is protected by the object lock, while *clearing* of bo->resource is also protected by the LRU lock. This means that if we check that bo->resource points to the LRU resource under the LRU lock we should be safe. So perform that check before deciding to swap out a bo. That avoids dereferencing a NULL bo->resource in ttm_bo_swapout().

In the Linux kernel, the following vulnerability has been resolved: media: az6007: Fix null-ptr-deref in az6007_i2c_xfer() In az6007_i2c_xfer, msg is controlled by user. When msg[i].buf is null and msg[i].len is zero, former checks on msg[i].buf would be passed. Malicious data finally reach az6007_i2c_xfer. If accessing msg[i].buf[0] without sanity check, null ptr deref would happen. We add check on msg[i].len to prevent crash. Similar commit: commit 0ed554fd769a ("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()")

In the Linux kernel, the following vulnerability has been resolved: ALSA: hda: Do not unset preset when cleaning up codec Several functions that take part in codec's initialization and removal are re-used by ASoC codec drivers implementations. Drivers mimic the behavior of hda_codec_driver_probe/remove() found in sound/pci/hda/hda_bind.c with their component->probe/remove() instead. One of the reasons for that is the expectation of snd_hda_codec_device_new() to receive a valid pointer to an instance of struct snd_card. This expectation can be met only once sound card components probing commences. As ASoC sound card may be unbound without codec device being actually removed from the system, unsetting ->preset in snd_hda_codec_cleanup_for_unbind() interferes with module unload -> load scenario causing null-ptr-deref. Preset is assigned only once, during device/driver matching whereas ASoC codec driver's module reloading may occur several times throughout the lifetime of an audio stack.

In the Linux kernel, the following vulnerability has been resolved: powerpc/mm: Fix null-pointer dereference in pgtable_cache_add kasprintf() returns a pointer to dynamically allocated memory which can be NULL upon failure. Ensure the allocation was successful by checking the pointer validity.

In the Linux kernel, the following vulnerability has been resolved: scsi: hisi_sas: Set debugfs_dir pointer to NULL after removing debugfs If init debugfs failed during device registration due to memory allocation failure, debugfs_remove_recursive() is called, after which debugfs_dir is not set to NULL. debugfs_remove_recursive() will be called again during device removal. As a result, illegal pointer is accessed. [ 1665.467244] hisi_sas_v3_hw 0000:b4:02.0: failed to init debugfs! ... [ 1669.836708] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000a0 [ 1669.872669] pc : down_write+0x24/0x70 [ 1669.876315] lr : down_write+0x1c/0x70 [ 1669.879961] sp : ffff000036f53a30 [ 1669.883260] x29: ffff000036f53a30 x28: ffffa027c31549f8 [ 1669.888547] x27: ffffa027c3140000 x26: 0000000000000000 [ 1669.893834] x25: ffffa027bf37c270 x24: ffffa027bf37c270 [ 1669.899122] x23: ffff0000095406b8 x22: ffff0000095406a8 [ 1669.904408] x21: 0000000000000000 x20: ffffa027bf37c310 [ 1669.909695] x19: 00000000000000a0 x18: ffff8027dcd86f10 [ 1669.914982] x17: 0000000000000000 x16: 0000000000000000 [ 1669.920268] x15: 0000000000000000 x14: ffffa0274014f870 [ 1669.925555] x13: 0000000000000040 x12: 0000000000000228 [ 1669.930842] x11: 0000000000000020 x10: 0000000000000bb0 [ 1669.936129] x9 : ffff000036f537f0 x8 : ffff80273088ca10 [ 1669.941416] x7 : 000000000000001d x6 : 00000000ffffffff [ 1669.946702] x5 : ffff000008a36310 x4 : ffff80273088be00 [ 1669.951989] x3 : ffff000009513e90 x2 : 0000000000000000 [ 1669.957276] x1 : 00000000000000a0 x0 : ffffffff00000001 [ 1669.962563] Call trace: [ 1669.965000] down_write+0x24/0x70 [ 1669.968301] debugfs_remove_recursive+0x5c/0x1b0 [ 1669.972905] hisi_sas_debugfs_exit+0x24/0x30 [hisi_sas_main] [ 1669.978541] hisi_sas_v3_remove+0x130/0x150 [hisi_sas_v3_hw] [ 1669.984175] pci_device_remove+0x48/0xd8 [ 1669.988082] device_release_driver_internal+0x1b4/0x250 [ 1669.993282] device_release_driver+0x28/0x38 [ 1669.997534] pci_stop_bus_device+0x84/0xb8 [ 1670.001611] pci_stop_and_remove_bus_device_locked+0x24/0x40 [ 1670.007244] remove_store+0xfc/0x140 [ 1670.010802] dev_attr_store+0x44/0x60 [ 1670.014448] sysfs_kf_write+0x58/0x80 [ 1670.018095] kernfs_fop_write+0xe8/0x1f0 [ 1670.022000] __vfs_write+0x60/0x190 [ 1670.025472] vfs_write+0xac/0x1c0 [ 1670.028771] ksys_write+0x6c/0xd8 [ 1670.032071] __arm64_sys_write+0x24/0x30 [ 1670.035977] el0_svc_common+0x78/0x130 [ 1670.039710] el0_svc_handler+0x38/0x78 [ 1670.043442] el0_svc+0x8/0xc To fix this, set debugfs_dir to NULL after debugfs_remove_recursive().

In the Linux kernel, the following vulnerability has been resolved: power: supply: Fix null pointer dereference in smb2_probe devm_kasprintf and devm_kzalloc return a pointer to dynamically allocated memory which can be NULL upon failure.

In the Linux kernel, the following vulnerability has been resolved: media: v4l: async: Fix duplicated list deletion The list deletion call dropped here is already called from the helper function in the line before. Having a second list_del() call results in either a warning (with CONFIG_DEBUG_LIST=y): list_del corruption, c46c8198->next is LIST_POISON1 (00000100) If CONFIG_DEBUG_LIST is disabled the operation results in a kernel error due to NULL pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: pcie: fix NULL pointer dereference in iwl_pcie_irq_rx_msix_handler() rxq can be NULL only when trans_pcie->rxq is NULL and entry->entry is zero. For the case when entry->entry is not equal to 0, rxq won't be NULL even if trans_pcie->rxq is NULL. Modify checker to check for trans_pcie->rxq.

In the Linux kernel, the following vulnerability has been resolved: hwmon: (pmbus_core) Fix NULL pointer dereference Pass i2c_client to _pmbus_is_enabled to drop the assumption that a regulator device is passed in. This will fix the issue of a NULL pointer dereference when called from _pmbus_get_flags.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix peer flow lists handling The cited change refactored mlx5e_tc_del_fdb_peer_flow() to only clear DUP flag when list of peer flows has become empty. However, if any concurrent user holds a reference to a peer flow (for example, the neighbor update workqueue task is updating peer flow's parent encap entry concurrently), then the flow will not be removed from the peer list and, consecutively, DUP flag will remain set. Since mlx5e_tc_del_fdb_peers_flow() calls mlx5e_tc_del_fdb_peer_flow() for every possible peer index the algorithm will try to remove the flow from eswitch instances that it has never peered with causing either NULL pointer dereference when trying to remove the flow peer list head of peer_index that was never initialized or a warning if the list debug config is enabled[0]. Fix the issue by always removing the peer flow from the list even when not releasing the last reference to it. [0]: [ 3102.985806] ------------[ cut here ]------------ [ 3102.986223] list_del corruption, ffff888139110698->next is NULL [ 3102.986757] WARNING: CPU: 2 PID: 22109 at lib/list_debug.c:53 __list_del_entry_valid_or_report+0x4f/0xc0 [ 3102.987561] Modules linked in: act_ct nf_flow_table bonding act_tunnel_key act_mirred act_skbedit vxlan cls_matchall nfnetlink_cttimeout act_gact cls_flower sch_ingress mlx5_vdpa vringh vhost_iotlb vdpa openvswitch nsh xt_MASQUERADE nf_conntrack_netlink nfnetlink iptable_nat xt_addrtype xt_conntrack nf_nat br_netfilter rpcsec_gss_krb5 auth_rpcg ss oid_registry overlay rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi ib_umad rdma_cm ib_ipoib iw_cm ib_cm mlx5_ib ib_uverbs ib_core mlx5_core [last unloaded: bonding] [ 3102.991113] CPU: 2 PID: 22109 Comm: revalidator28 Not tainted 6.6.0-rc6+ #3 [ 3102.991695] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 [ 3102.992605] RIP: 0010:__list_del_entry_valid_or_report+0x4f/0xc0 [ 3102.993122] Code: 39 c2 74 56 48 8b 32 48 39 fe 75 62 48 8b 51 08 48 39 f2 75 73 b8 01 00 00 00 c3 48 89 fe 48 c7 c7 48 fd 0a 82 e8 41 0b ad ff <0f> 0b 31 c0 c3 48 89 fe 48 c7 c7 70 fd 0a 82 e8 2d 0b ad ff 0f 0b [ 3102.994615] RSP: 0018:ffff8881383e7710 EFLAGS: 00010286 [ 3102.995078] RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000000 [ 3102.995670] RDX: 0000000000000001 RSI: ffff88885f89b640 RDI: ffff88885f89b640 [ 3102.997188] DEL flow 00000000be367878 on port 0 [ 3102.998594] RBP: dead000000000122 R08: 0000000000000000 R09: c0000000ffffdfff [ 3102.999604] R10: 0000000000000008 R11: ffff8881383e7598 R12: dead000000000100 [ 3103.000198] R13: 0000000000000002 R14: ffff888139110000 R15: ffff888101901240 [ 3103.000790] FS: 00007f424cde4700(0000) GS:ffff88885f880000(0000) knlGS:0000000000000000 [ 3103.001486] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 3103.001986] CR2: 00007fd42e8dcb70 CR3: 000000011e68a003 CR4: 0000000000370ea0 [ 3103.002596] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 3103.003190] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 3103.003787] Call Trace: [ 3103.004055] <TASK> [ 3103.004297] ? __warn+0x7d/0x130 [ 3103.004623] ? __list_del_entry_valid_or_report+0x4f/0xc0 [ 3103.005094] ? report_bug+0xf1/0x1c0 [ 3103.005439] ? console_unlock+0x4a/0xd0 [ 3103.005806] ? handle_bug+0x3f/0x70 [ 3103.006149] ? exc_invalid_op+0x13/0x60 [ 3103.006531] ? asm_exc_invalid_op+0x16/0x20 [ 3103.007430] ? __list_del_entry_valid_or_report+0x4f/0xc0 [ 3103.007910] mlx5e_tc_del_fdb_peers_flow+0xcf/0x240 [mlx5_core] [ 3103.008463] mlx5e_tc_del_flow+0x46/0x270 [mlx5_core] [ 3103.008944] mlx5e_flow_put+0x26/0x50 [mlx5_core] [ 3103.009401] mlx5e_delete_flower+0x25f/0x380 [mlx5_core] [ 3103.009901] tc_setup_cb_destroy+0xab/0x180 [ 3103.010292] fl_hw_destroy_filter+0x99/0xc0 [cls_flower] [ 3103.010779] __fl_delete+0x2d4/0x2f0 [cls_flower] [ 3103.0 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: usb: typec: ucsi: Don't attempt to resume the ports before they exist This will fix null pointer dereference that was caused by the driver attempting to resume ports that were not yet registered.

In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Remove unused nvme_ls_waitq wait queue System crash when qla2x00_start_sp(sp) returns error code EGAIN and wake_up gets called for uninitialized wait queue sp->nvme_ls_waitq. qla2xxx [0000:37:00.1]-2121:5: Returning existing qpair of ffff8ae2c0513400 for idx=0 qla2xxx [0000:37:00.1]-700e:5: qla2x00_start_sp failed = 11 BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 PGD 0 P4D 0 Oops: 0000 [#1] SMP NOPTI Hardware name: HPE ProLiant DL360 Gen10/ProLiant DL360 Gen10, BIOS U32 09/03/2021 Workqueue: nvme-wq nvme_fc_connect_ctrl_work [nvme_fc] RIP: 0010:__wake_up_common+0x4c/0x190 RSP: 0018:ffff95f3e0cb7cd0 EFLAGS: 00010086 RAX: 0000000000000000 RBX: ffff8b08d3b26328 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 0000000000000003 RDI: ffff8b08d3b26320 RBP: 0000000000000001 R08: 0000000000000000 R09: ffffffffffffffe8 R10: 0000000000000000 R11: ffff95f3e0cb7a60 R12: ffff95f3e0cb7d20 R13: 0000000000000003 R14: 0000000000000000 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff8b2fdf6c0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 0000002f1e410002 CR4: 00000000007706e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: __wake_up_common_lock+0x7c/0xc0 qla_nvme_ls_req+0x355/0x4c0 [qla2xxx] ? __nvme_fc_send_ls_req+0x260/0x380 [nvme_fc] ? nvme_fc_send_ls_req.constprop.42+0x1a/0x45 [nvme_fc] ? nvme_fc_connect_ctrl_work.cold.63+0x1e3/0xa7d [nvme_fc] Remove unused nvme_ls_waitq wait queue. nvme_ls_waitq logic was removed previously in the commits tagged Fixed: below.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: btusb: Add date->evt_skb is NULL check fix crash because of null pointers [ 6104.969662] BUG: kernel NULL pointer dereference, address: 00000000000000c8 [ 6104.969667] #PF: supervisor read access in kernel mode [ 6104.969668] #PF: error_code(0x0000) - not-present page [ 6104.969670] PGD 0 P4D 0 [ 6104.969673] Oops: 0000 [#1] SMP NOPTI [ 6104.969684] RIP: 0010:btusb_mtk_hci_wmt_sync+0x144/0x220 [btusb] [ 6104.969688] RSP: 0018:ffffb8d681533d48 EFLAGS: 00010246 [ 6104.969689] RAX: 0000000000000000 RBX: ffff8ad560bb2000 RCX: 0000000000000006 [ 6104.969691] RDX: 0000000000000000 RSI: ffffb8d681533d08 RDI: 0000000000000000 [ 6104.969692] RBP: ffffb8d681533d70 R08: 0000000000000001 R09: 0000000000000001 [ 6104.969694] R10: 0000000000000001 R11: 00000000fa83b2da R12: ffff8ad461d1d7c0 [ 6104.969695] R13: 0000000000000000 R14: ffff8ad459618c18 R15: ffffb8d681533d90 [ 6104.969697] FS: 00007f5a1cab9d40(0000) GS:ffff8ad578200000(0000) knlGS:00000 [ 6104.969699] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 6104.969700] CR2: 00000000000000c8 CR3: 000000018620c001 CR4: 0000000000760ef0 [ 6104.969701] PKRU: 55555554 [ 6104.969702] Call Trace: [ 6104.969708] btusb_mtk_shutdown+0x44/0x80 [btusb] [ 6104.969732] hci_dev_do_close+0x470/0x5c0 [bluetooth] [ 6104.969748] hci_rfkill_set_block+0x56/0xa0 [bluetooth] [ 6104.969753] rfkill_set_block+0x92/0x160 [ 6104.969755] rfkill_fop_write+0x136/0x1e0 [ 6104.969759] __vfs_write+0x18/0x40 [ 6104.969761] vfs_write+0xdf/0x1c0 [ 6104.969763] ksys_write+0xb1/0xe0 [ 6104.969765] __x64_sys_write+0x1a/0x20 [ 6104.969769] do_syscall_64+0x51/0x180 [ 6104.969771] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 6104.969773] RIP: 0033:0x7f5a21f18fef [ 6104.9] RSP: 002b:00007ffeefe39010 EFLAGS: 00000293 ORIG_RAX: 0000000000000001 [ 6104.969780] RAX: ffffffffffffffda RBX: 000055c10a7560a0 RCX: 00007f5a21f18fef [ 6104.969781] RDX: 0000000000000008 RSI: 00007ffeefe39060 RDI: 0000000000000012 [ 6104.969782] RBP: 00007ffeefe39060 R08: 0000000000000000 R09: 0000000000000017 [ 6104.969784] R10: 00007ffeefe38d97 R11: 0000000000000293 R12: 0000000000000002 [ 6104.969785] R13: 00007ffeefe39220 R14: 00007ffeefe391a0 R15: 000055c10a72acf0

In the Linux kernel, the following vulnerability has been resolved: tls: fix NULL deref on tls_sw_splice_eof() with empty record syzkaller discovered that if tls_sw_splice_eof() is executed as part of sendfile() when the plaintext/ciphertext sk_msg are empty, the send path gets confused because the empty ciphertext buffer does not have enough space for the encryption overhead. This causes tls_push_record() to go on the `split = true` path (which is only supposed to be used when interacting with an attached BPF program), and then get further confused and hit the tls_merge_open_record() path, which then assumes that there must be at least one populated buffer element, leading to a NULL deref. It is possible to have empty plaintext/ciphertext buffers if we previously bailed from tls_sw_sendmsg_locked() via the tls_trim_both_msgs() path. tls_sw_push_pending_record() already handles this case correctly; let's do the same check in tls_sw_splice_eof().

In the Linux kernel, the following vulnerability has been resolved: scsi: mpt3sas: Fix NULL pointer access in mpt3sas_transport_port_add() Port is allocated by sas_port_alloc_num() and rphy is allocated by either sas_end_device_alloc() or sas_expander_alloc(), all of which may return NULL. So we need to check the rphy to avoid possible NULL pointer access. If sas_rphy_add() returned with failure, rphy is set to NULL. We would access the rphy in the following lines which would also result NULL pointer access.