In the Linux kernel, the following vulnerability has been resolved: btrfs: check folio mapping after unlock in relocate_one_folio() When we call btrfs_read_folio() to bring a folio uptodate, we unlock the folio. The result of that is that a different thread can modify the mapping (like remove it with invalidate) before we call folio_lock(). This results in an invalid page and we need to try again. In particular, if we are relocating concurrently with aborting a transaction, this can result in a crash like the following: BUG: kernel NULL pointer dereference, address: 0000000000000000 PGD 0 P4D 0 Oops: 0000 [#1] SMP CPU: 76 PID: 1411631 Comm: kworker/u322:5 Workqueue: events_unbound btrfs_reclaim_bgs_work RIP: 0010:set_page_extent_mapped+0x20/0xb0 RSP: 0018:ffffc900516a7be8 EFLAGS: 00010246 RAX: ffffea009e851d08 RBX: ffffea009e0b1880 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffffc900516a7b90 RDI: ffffea009e0b1880 RBP: 0000000003573000 R08: 0000000000000001 R09: ffff88c07fd2f3f0 R10: 0000000000000000 R11: 0000194754b575be R12: 0000000003572000 R13: 0000000003572fff R14: 0000000000100cca R15: 0000000005582fff FS: 0000000000000000(0000) GS:ffff88c07fd00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 000000407d00f002 CR4: 00000000007706f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> ? __die+0x78/0xc0 ? page_fault_oops+0x2a8/0x3a0 ? __switch_to+0x133/0x530 ? wq_worker_running+0xa/0x40 ? exc_page_fault+0x63/0x130 ? asm_exc_page_fault+0x22/0x30 ? set_page_extent_mapped+0x20/0xb0 relocate_file_extent_cluster+0x1a7/0x940 relocate_data_extent+0xaf/0x120 relocate_block_group+0x20f/0x480 btrfs_relocate_block_group+0x152/0x320 btrfs_relocate_chunk+0x3d/0x120 btrfs_reclaim_bgs_work+0x2ae/0x4e0 process_scheduled_works+0x184/0x370 worker_thread+0xc6/0x3e0 ? blk_add_timer+0xb0/0xb0 kthread+0xae/0xe0 ? flush_tlb_kernel_range+0x90/0x90 ret_from_fork+0x2f/0x40 ? flush_tlb_kernel_range+0x90/0x90 ret_from_fork_asm+0x11/0x20 </TASK> This occurs because cleanup_one_transaction() calls destroy_delalloc_inodes() which calls invalidate_inode_pages2() which takes the folio_lock before setting mapping to NULL. We fail to check this, and subsequently call set_extent_mapping(), which assumes that mapping != NULL (in fact it asserts that in debug mode) Note that the "fixes" patch here is not the one that introduced the race (the very first iteration of this code from 2009) but a more recent change that made this particular crash happen in practice.

In the Linux kernel, the following vulnerability has been resolved: PCI: endpoint: epf-mhi: Avoid NULL dereference if DT lacks 'mmio' If platform_get_resource_byname() fails and returns NULL because DT lacks an 'mmio' property for the MHI endpoint, dereferencing res->start will cause a NULL pointer access. Add a check to prevent it. [kwilczynski: error message update per the review feedback] [bhelgaas: commit log]

In the Linux kernel, the following vulnerability has been resolved: media: amphion: Set video drvdata before register video device The video drvdata should be set before the video device is registered, otherwise video_drvdata() may return NULL in the open() file ops, and led to oops.

In the Linux kernel, the following vulnerability has been resolved: drm/msm: adreno: fix deferencing ifpc_reglist when not declared On plaforms with an a7xx GPU not supporting IFPC, the ifpc_reglist if still deferenced in a7xx_patch_pwrup_reglist() which causes a kernel crash: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008 ... pc : a6xx_hw_init+0x155c/0x1e4c [msm] lr : a6xx_hw_init+0x9a8/0x1e4c [msm] ... Call trace: a6xx_hw_init+0x155c/0x1e4c [msm] (P) msm_gpu_hw_init+0x58/0x88 [msm] adreno_load_gpu+0x94/0x1fc [msm] msm_open+0xe4/0xf4 [msm] drm_file_alloc+0x1a0/0x2e4 [drm] drm_client_init+0x7c/0x104 [drm] drm_fbdev_client_setup+0x94/0xcf0 [drm_client_lib] drm_client_setup+0xb4/0xd8 [drm_client_lib] msm_drm_kms_post_init+0x2c/0x3c [msm] msm_drm_init+0x1a4/0x228 [msm] msm_drm_bind+0x30/0x3c [msm] ... Check the validity of ifpc_reglist before deferencing the table to setup the register values. Patchwork: https://patchwork.freedesktop.org/patch/688944/

In the Linux kernel, the following vulnerability has been resolved: gpio: grgpio: Add NULL check in grgpio_probe devm_kasprintf() can return a NULL pointer on failure,but this returned value in grgpio_probe is not checked. Add NULL check in grgpio_probe, to handle kernel NULL pointer dereference error.

In the Linux kernel, the following vulnerability has been resolved: misc: bcm_vk: Fix possible null-pointer dereferences in bcm_vk_read() In the function bcm_vk_read(), the pointer entry is checked, indicating that it can be NULL. If entry is NULL and rc is set to -EMSGSIZE, the following code may cause null-pointer dereferences: struct vk_msg_blk tmp_msg = entry->to_h_msg[0]; set_msg_id(&tmp_msg, entry->usr_msg_id); tmp_msg.size = entry->to_h_blks - 1; To prevent these possible null-pointer dereferences, copy to_h_msg, usr_msg_id, and to_h_blks from iter into temporary variables, and return these temporary variables to the application instead of accessing them through a potentially NULL entry.

In the Linux kernel, the following vulnerability has been resolved: irqchip/riscv-aplic: Prevent crash when MSI domain is missing If the APLIC driver is probed before the IMSIC driver, the parent MSI domain will be missing, which causes a NULL pointer dereference in msi_create_device_irq_domain(). Avoid this by deferring probe until the parent MSI domain is available. Use dev_err_probe() to avoid printing an error message when returning -EPROBE_DEFER.

In the Linux kernel, the following vulnerability has been resolved: net/9p/usbg: fix handling of the failed kzalloc() memory allocation On the linux-next, next-20241108 vanilla kernel, the coccinelle tool gave the following error report: ./net/9p/trans_usbg.c:912:5-11: ERROR: allocation function on line 911 returns NULL not ERR_PTR on failure kzalloc() failure is fixed to handle the NULL return case on the memory exhaustion.

In the Linux kernel, the following vulnerability has been resolved: cachefiles: Fix NULL pointer dereference in object->file At present, the object->file has the NULL pointer dereference problem in ondemand-mode. The root cause is that the allocated fd and object->file lifetime are inconsistent, and the user-space invocation to anon_fd uses object->file. Following is the process that triggers the issue: [write fd] [umount] cachefiles_ondemand_fd_write_iter fscache_cookie_state_machine cachefiles_withdraw_cookie if (!file) return -ENOBUFS cachefiles_clean_up_object cachefiles_unmark_inode_in_use fput(object->file) object->file = NULL // file NULL pointer dereference! __cachefiles_write(..., file, ...) Fix this issue by add an additional reference count to the object->file before write/llseek, and decrement after it finished.

In the Linux kernel, the following vulnerability has been resolved: ftrace: Fix regression with module command in stack_trace_filter When executing the following command: # echo "write*:mod:ext3" > /sys/kernel/tracing/stack_trace_filter The current mod command causes a null pointer dereference. While commit 0f17976568b3f ("ftrace: Fix regression with module command in stack_trace_filter") has addressed part of the issue, it left a corner case unhandled, which still results in a kernel crash.

In the Linux kernel, the following vulnerability has been resolved: btrfs: add a sanity check for btrfs root in btrfs_search_slot() Syzbot reports a null-ptr-deref in btrfs_search_slot(). The reproducer is using rescue=ibadroots, and the extent tree root is corrupted thus the extent tree is NULL. When scrub tries to search the extent tree to gather the needed extent info, btrfs_search_slot() doesn't check if the target root is NULL or not, resulting the null-ptr-deref. Add sanity check for btrfs root before using it in btrfs_search_slot().

In the Linux kernel, the following vulnerability has been resolved: wifi: cw1200: Fix potential NULL dereference A recent refactoring was identified by static analysis to cause a potential NULL dereference, fix this!

In the Linux kernel, the following vulnerability has been resolved: drm/msm/mdp5: Add check for kzalloc As kzalloc may fail and return NULL pointer, it should be better to check the return value in order to avoid the NULL pointer dereference. Patchwork: https://patchwork.freedesktop.org/patch/514154/

In the Linux kernel, the following vulnerability has been resolved: usb: dwc3: gadget: Fix looping of queued SG entries The dwc3_request->num_queued_sgs is decremented on completion. If a partially completed request is handled, then the dwc3_request->num_queued_sgs no longer reflects the total number of num_queued_sgs (it would be cleared). Correctly check the number of request SG entries remained to be prepare and queued. Failure to do this may cause null pointer dereference when accessing non-existent SG entry.

In the Linux kernel, the following vulnerability has been resolved: cacheinfo: Allocate memory during CPU hotplug if not done from the primary CPU Commit 5944ce092b97 ("arch_topology: Build cacheinfo from primary CPU") adds functionality that architectures can use to optionally allocate and build cacheinfo early during boot. Commit 6539cffa9495 ("cacheinfo: Add arch specific early level initializer") lets secondary CPUs correct (and reallocate memory) cacheinfo data if needed. If the early build functionality is not used and cacheinfo does not need correction, memory for cacheinfo is never allocated. x86 does not use the early build functionality. Consequently, during the cacheinfo CPU hotplug callback, last_level_cache_is_valid() attempts to dereference a NULL pointer: BUG: kernel NULL pointer dereference, address: 0000000000000100 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not present page PGD 0 P4D 0 Oops: 0000 [#1] PREEPMT SMP NOPTI CPU: 0 PID 19 Comm: cpuhp/0 Not tainted 6.4.0-rc2 #1 RIP: 0010: last_level_cache_is_valid+0x95/0xe0a Allocate memory for cacheinfo during the cacheinfo CPU hotplug callback if not done earlier. Moreover, before determining the validity of the last-level cache info, ensure that it has been allocated. Simply checking for non-zero cache_leaves() is not sufficient, as some architectures (e.g., Intel processors) have non-zero cache_leaves() before allocation. Dereferencing NULL cacheinfo can occur in update_per_cpu_data_slice_size(). This function iterates over all online CPUs. However, a CPU may have come online recently, but its cacheinfo may not have been allocated yet. While here, remove an unnecessary indentation in allocate_cache_info(). [ bp: Massage. ]

In the Linux kernel, the following vulnerability has been resolved: scsi: ufs: core: Cancel RTC work during ufshcd_remove() Currently, RTC work is only cancelled during __ufshcd_wl_suspend(). When ufshcd is removed in ufshcd_remove(), RTC work is not cancelled. Due to this, any further trigger of the RTC work after ufshcd_remove() would result in a NULL pointer dereference as below: Unable to handle kernel NULL pointer dereference at virtual address 00000000000002a4 Workqueue: events ufshcd_rtc_work Call trace: _raw_spin_lock_irqsave+0x34/0x8c pm_runtime_get_if_active+0x24/0xb4 ufshcd_rtc_work+0x124/0x19c process_scheduled_works+0x18c/0x2d8 worker_thread+0x144/0x280 kthread+0x11c/0x128 ret_from_fork+0x10/0x20 Since RTC work accesses the ufshcd internal structures, it should be cancelled when ufshcd is removed. So do that in ufshcd_remove(), as per the order in ufshcd_init().

In the Linux kernel, the following vulnerability has been resolved: zram: fix NULL pointer in comp_algorithm_show() LTP reported a NULL pointer dereference as followed: CPU: 7 UID: 0 PID: 5995 Comm: cat Kdump: loaded Not tainted 6.12.0-rc6+ #3 Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015 pstate: 40400005 (nZcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : __pi_strcmp+0x24/0x140 lr : zcomp_available_show+0x60/0x100 [zram] sp : ffff800088b93b90 x29: ffff800088b93b90 x28: 0000000000000001 x27: 0000000000400cc0 x26: 0000000000000ffe x25: ffff80007b3e2388 x24: 0000000000000000 x23: ffff80007b3e2390 x22: ffff0004041a9000 x21: ffff80007b3e2900 x20: 0000000000000000 x19: 0000000000000000 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000 x11: 0000000000000000 x10: ffff80007b3e2900 x9 : ffff80007b3cb280 x8 : 0101010101010101 x7 : 0000000000000000 x6 : 0000000000000000 x5 : 0000000000000040 x4 : 0000000000000000 x3 : 00656c722d6f7a6c x2 : 0000000000000000 x1 : ffff80007b3e2900 x0 : 0000000000000000 Call trace: __pi_strcmp+0x24/0x140 comp_algorithm_show+0x40/0x70 [zram] dev_attr_show+0x28/0x80 sysfs_kf_seq_show+0x90/0x140 kernfs_seq_show+0x34/0x48 seq_read_iter+0x1d4/0x4e8 kernfs_fop_read_iter+0x40/0x58 new_sync_read+0x9c/0x168 vfs_read+0x1a8/0x1f8 ksys_read+0x74/0x108 __arm64_sys_read+0x24/0x38 invoke_syscall+0x50/0x120 el0_svc_common.constprop.0+0xc8/0xf0 do_el0_svc+0x24/0x38 el0_svc+0x38/0x138 el0t_64_sync_handler+0xc0/0xc8 el0t_64_sync+0x188/0x190 The zram->comp_algs[ZRAM_PRIMARY_COMP] can be NULL in zram_add() if comp_algorithm_set() has not been called. User can access the zram device by sysfs after device_add_disk(), so there is a time window to trigger the NULL pointer dereference. Move it ahead device_add_disk() to make sure when user can access the zram device, it is ready. comp_algorithm_set() is protected by zram->init_lock in other places and no such problem.

In the Linux kernel, the following vulnerability has been resolved: ip6_gre: make ip6gre_header() robust Over the years, syzbot found many ways to crash the kernel in ip6gre_header() [1]. This involves team or bonding drivers ability to dynamically change their dev->needed_headroom and/or dev->hard_header_len In this particular crash mld_newpack() allocated an skb with a too small reserve/headroom, and by the time mld_sendpack() was called, syzbot managed to attach an ip6gre device. [1] skbuff: skb_under_panic: text:ffffffff8a1d69a8 len:136 put:40 head:ffff888059bc7000 data:ffff888059bc6fe8 tail:0x70 end:0x6c0 dev:team0 ------------[ cut here ]------------ kernel BUG at net/core/skbuff.c:213 ! <TASK> skb_under_panic net/core/skbuff.c:223 [inline] skb_push+0xc3/0xe0 net/core/skbuff.c:2641 ip6gre_header+0xc8/0x790 net/ipv6/ip6_gre.c:1371 dev_hard_header include/linux/netdevice.h:3436 [inline] neigh_connected_output+0x286/0x460 net/core/neighbour.c:1618 neigh_output include/net/neighbour.h:556 [inline] ip6_finish_output2+0xfb3/0x1480 net/ipv6/ip6_output.c:136 __ip6_finish_output net/ipv6/ip6_output.c:-1 [inline] ip6_finish_output+0x234/0x7d0 net/ipv6/ip6_output.c:220 NF_HOOK_COND include/linux/netfilter.h:307 [inline] ip6_output+0x340/0x550 net/ipv6/ip6_output.c:247 NF_HOOK+0x9e/0x380 include/linux/netfilter.h:318 mld_sendpack+0x8d4/0xe60 net/ipv6/mcast.c:1855 mld_send_cr net/ipv6/mcast.c:2154 [inline] mld_ifc_work+0x83e/0xd60 net/ipv6/mcast.c:2693

In the Linux kernel, the following vulnerability has been resolved: ALSA: core: Fix possible NULL dereference caused by kunit_kzalloc() kunit_kzalloc() may return a NULL pointer, dereferencing it without NULL check may lead to NULL dereference. Add NULL checks for all the kunit_kzalloc() in sound_kunit.c

In the Linux kernel, the following vulnerability has been resolved: ACPI: x86: Add adev NULL check to acpi_quirk_skip_serdev_enumeration() acpi_dev_hid_match() does not check for adev == NULL, dereferencing it unconditional. Add a check for adev being NULL before calling acpi_dev_hid_match(). At the moment acpi_quirk_skip_serdev_enumeration() is never called with a controller_parent without an ACPI companion, but better safe than sorry.

In the Linux kernel, the following vulnerability has been resolved: netfilter: nft_set_rbtree: fix overlap expiration walk The lazy gc on insert that should remove timed-out entries fails to release the other half of the interval, if any. Can be reproduced with tests/shell/testcases/sets/0044interval_overlap_0 in nftables.git and kmemleak enabled kernel. Second bug is the use of rbe_prev vs. prev pointer. If rbe_prev() returns NULL after at least one iteration, rbe_prev points to element that is not an end interval, hence it should not be removed. Lastly, check the genmask of the end interval if this is active in the current generation.

In the Linux kernel, the following vulnerability has been resolved: scsi: iscsi_tcp: Check that sock is valid before iscsi_set_param() The validity of sock should be checked before assignment to avoid incorrect values. Commit 57569c37f0ad ("scsi: iscsi: iscsi_tcp: Fix null-ptr-deref while calling getpeername()") introduced this change which may lead to inconsistent values of tcp_sw_conn->sendpage and conn->datadgst_en. Fix the issue by moving the position of the assignment.

In the Linux kernel, the following vulnerability has been resolved: leds: class: Protect brightness_show() with led_cdev->led_access mutex There is NULL pointer issue observed if from Process A where hid device being added which results in adding a led_cdev addition and later a another call to access of led_cdev attribute from Process B can result in NULL pointer issue. Use mutex led_cdev->led_access to protect access to led->cdev and its attribute inside brightness_show() and max_brightness_show() and also update the comment for mutex that it should be used to protect the led class device fields. Process A Process B kthread+0x114 worker_thread+0x244 process_scheduled_works+0x248 uhid_device_add_worker+0x24 hid_add_device+0x120 device_add+0x268 bus_probe_device+0x94 device_initial_probe+0x14 __device_attach+0xfc bus_for_each_drv+0x10c __device_attach_driver+0x14c driver_probe_device+0x3c __driver_probe_device+0xa0 really_probe+0x190 hid_device_probe+0x130 ps_probe+0x990 ps_led_register+0x94 devm_led_classdev_register_ext+0x58 led_classdev_register_ext+0x1f8 device_create_with_groups+0x48 device_create_groups_vargs+0xc8 device_add+0x244 kobject_uevent+0x14 kobject_uevent_env[jt]+0x224 mutex_unlock[jt]+0xc4 __mutex_unlock_slowpath+0xd4 wake_up_q+0x70 try_to_wake_up[jt]+0x48c preempt_schedule_common+0x28 __schedule+0x628 __switch_to+0x174 el0t_64_sync+0x1a8/0x1ac el0t_64_sync_handler+0x68/0xbc el0_svc+0x38/0x68 do_el0_svc+0x1c/0x28 el0_svc_common+0x80/0xe0 invoke_syscall+0x58/0x114 __arm64_sys_read+0x1c/0x2c ksys_read+0x78/0xe8 vfs_read+0x1e0/0x2c8 kernfs_fop_read_iter+0x68/0x1b4 seq_read_iter+0x158/0x4ec kernfs_seq_show+0x44/0x54 sysfs_kf_seq_show+0xb4/0x130 dev_attr_show+0x38/0x74 brightness_show+0x20/0x4c dualshock4_led_get_brightness+0xc/0x74 [ 3313.874295][ T4013] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000060 [ 3313.874301][ T4013] Mem abort info: [ 3313.874303][ T4013] ESR = 0x0000000096000006 [ 3313.874305][ T4013] EC = 0x25: DABT (current EL), IL = 32 bits [ 3313.874307][ T4013] SET = 0, FnV = 0 [ 3313.874309][ T4013] EA = 0, S1PTW = 0 [ 3313.874311][ T4013] FSC = 0x06: level 2 translation fault [ 3313.874313][ T4013] Data abort info: [ 3313.874314][ T4013] ISV = 0, ISS = 0x00000006, ISS2 = 0x00000000 [ 3313.874316][ T4013] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 3313.874318][ T4013] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 3313.874320][ T4013] user pgtable: 4k pages, 39-bit VAs, pgdp=00000008f2b0a000 .. [ 3313.874332][ T4013] Dumping ftrace buffer: [ 3313.874334][ T4013] (ftrace buffer empty) .. .. [ dd3313.874639][ T4013] CPU: 6 PID: 4013 Comm: InputReader [ 3313.874648][ T4013] pc : dualshock4_led_get_brightness+0xc/0x74 [ 3313.874653][ T4013] lr : led_update_brightness+0x38/0x60 [ 3313.874656][ T4013] sp : ffffffc0b910bbd0 .. .. [ 3313.874685][ T4013] Call trace: [ 3313.874687][ T4013] dualshock4_led_get_brightness+0xc/0x74 [ 3313.874690][ T4013] brightness_show+0x20/0x4c [ 3313.874692][ T4013] dev_attr_show+0x38/0x74 [ 3313.874696][ T4013] sysfs_kf_seq_show+0xb4/0x130 [ 3313.874700][ T4013] kernfs_seq_show+0x44/0x54 [ 3313.874703][ T4013] seq_read_iter+0x158/0x4ec [ 3313.874705][ T4013] kernfs_fop_read_iter+0x68/0x1b4 [ 3313.874708][ T4013] vfs_read+0x1e0/0x2c8 [ 3313.874711][ T4013] ksys_read+0x78/0xe8 [ 3313.874714][ T4013] __arm64_sys_read+0x1c/0x2c [ 3313.874718][ T4013] invoke_syscall+0x58/0x114 [ 3313.874721][ T4013] el0_svc_common+0x80/0xe0 [ 3313.874724][ T4013] do_el0_svc+0x1c/0x28 [ 3313.874727][ T4013] el0_svc+0x38/0x68 [ 3313.874730][ T4013] el0t_64_sync_handler+0x68/0xbc [ 3313.874732][ T4013] el0t_64_sync+0x1a8/0x1ac

In the Linux kernel, the following vulnerability has been resolved: media: imx-jpeg: Ensure power suppliers be suspended before detach them The power suppliers are always requested to suspend asynchronously, dev_pm_domain_detach() requires the caller to ensure proper synchronization of this function with power management callbacks. otherwise the detach may led to kernel panic, like below: [ 1457.107934] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000040 [ 1457.116777] Mem abort info: [ 1457.119589] ESR = 0x0000000096000004 [ 1457.123358] EC = 0x25: DABT (current EL), IL = 32 bits [ 1457.128692] SET = 0, FnV = 0 [ 1457.131764] EA = 0, S1PTW = 0 [ 1457.134920] FSC = 0x04: level 0 translation fault [ 1457.139812] Data abort info: [ 1457.142707] ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 [ 1457.148196] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 1457.153256] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 1457.158563] user pgtable: 4k pages, 48-bit VAs, pgdp=00000001138b6000 [ 1457.165000] [0000000000000040] pgd=0000000000000000, p4d=0000000000000000 [ 1457.171792] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP [ 1457.178045] Modules linked in: v4l2_jpeg wave6_vpu_ctrl(-) [last unloaded: mxc_jpeg_encdec] [ 1457.186383] CPU: 0 PID: 51938 Comm: kworker/0:3 Not tainted 6.6.36-gd23d64eea511 #66 [ 1457.194112] Hardware name: NXP i.MX95 19X19 board (DT) [ 1457.199236] Workqueue: pm pm_runtime_work [ 1457.203247] pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 1457.210188] pc : genpd_runtime_suspend+0x20/0x290 [ 1457.214886] lr : __rpm_callback+0x48/0x1d8 [ 1457.218968] sp : ffff80008250bc50 [ 1457.222270] x29: ffff80008250bc50 x28: 0000000000000000 x27: 0000000000000000 [ 1457.229394] x26: 0000000000000000 x25: 0000000000000008 x24: 00000000000f4240 [ 1457.236518] x23: 0000000000000000 x22: ffff00008590f0e4 x21: 0000000000000008 [ 1457.243642] x20: ffff80008099c434 x19: ffff00008590f000 x18: ffffffffffffffff [ 1457.250766] x17: 5300326563697665 x16: 645f676e696c6f6f x15: 63343a6d726f6674 [ 1457.257890] x14: 0000000000000004 x13: 00000000000003a4 x12: 0000000000000002 [ 1457.265014] x11: 0000000000000000 x10: 0000000000000a60 x9 : ffff80008250bbb0 [ 1457.272138] x8 : ffff000092937200 x7 : ffff0003fdf6af80 x6 : 0000000000000000 [ 1457.279262] x5 : 00000000410fd050 x4 : 0000000000200000 x3 : 0000000000000000 [ 1457.286386] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff00008590f000 [ 1457.293510] Call trace: [ 1457.295946] genpd_runtime_suspend+0x20/0x290 [ 1457.300296] __rpm_callback+0x48/0x1d8 [ 1457.304038] rpm_callback+0x6c/0x78 [ 1457.307515] rpm_suspend+0x10c/0x570 [ 1457.311077] pm_runtime_work+0xc4/0xc8 [ 1457.314813] process_one_work+0x138/0x248 [ 1457.318816] worker_thread+0x320/0x438 [ 1457.322552] kthread+0x110/0x114 [ 1457.325767] ret_from_fork+0x10/0x20

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: u_serial: Fix the issue that gs_start_io crashed due to accessing null pointer Considering that in some extreme cases, when u_serial driver is accessed by multiple threads, Thread A is executing the open operation and calling the gs_open, Thread B is executing the disconnect operation and calling the gserial_disconnect function,The port->port_usb pointer will be set to NULL. E.g. Thread A Thread B gs_open() gadget_unbind_driver() gs_start_io() composite_disconnect() gs_start_rx() gserial_disconnect() ... ... spin_unlock(&port->port_lock) status = usb_ep_queue() spin_lock(&port->port_lock) spin_lock(&port->port_lock) port->port_usb = NULL gs_free_requests(port->port_usb->in) spin_unlock(&port->port_lock) Crash This causes thread A to access a null pointer (port->port_usb is null) when calling the gs_free_requests function, causing a crash. If port_usb is NULL, the release request will be skipped as it will be done by gserial_disconnect. So add a null pointer check to gs_start_io before attempting to access the value of the pointer port->port_usb. Call trace: gs_start_io+0x164/0x25c gs_open+0x108/0x13c tty_open+0x314/0x638 chrdev_open+0x1b8/0x258 do_dentry_open+0x2c4/0x700 vfs_open+0x2c/0x3c path_openat+0xa64/0xc60 do_filp_open+0xb8/0x164 do_sys_openat2+0x84/0xf0 __arm64_sys_openat+0x70/0x9c invoke_syscall+0x58/0x114 el0_svc_common+0x80/0xe0 do_el0_svc+0x1c/0x28 el0_svc+0x38/0x68

In the Linux kernel, the following vulnerability has been resolved: wifi: brcmfmac: Fix oops due to NULL pointer dereference in brcmf_sdiod_sglist_rw() This patch fixes a NULL pointer dereference bug in brcmfmac that occurs when a high 'sd_sgentry_align' value applies (e.g. 512) and a lot of queued SKBs are sent from the pkt queue. The problem is the number of entries in the pre-allocated sgtable, it is nents = max(rxglom_size, txglom_size) + max(rxglom_size, txglom_size) >> 4 + 1. Given the default [rt]xglom_size=32 it's actually 35 which is too small. Worst case, the pkt queue can end up with 64 SKBs. This occurs when a new SKB is added for each original SKB if tailroom isn't enough to hold tail_pad. At least one sg entry is needed for each SKB. So, eventually the "skb_queue_walk loop" in brcmf_sdiod_sglist_rw may run out of sg entries. This makes sg_next return NULL and this causes the oops. The patch sets nents to max(rxglom_size, txglom_size) * 2 to be able handle the worst-case. Btw. this requires only 64-35=29 * 16 (or 20 if CONFIG_NEED_SG_DMA_LENGTH) = 464 additional bytes of memory.

In the Linux kernel, the following vulnerability has been resolved: net: cdc_ncm: Deal with too low values of dwNtbOutMaxSize Currently in cdc_ncm_check_tx_max(), if dwNtbOutMaxSize is lower than the calculated "min" value, but greater than zero, the logic sets tx_max to dwNtbOutMaxSize. This is then used to allocate a new SKB in cdc_ncm_fill_tx_frame() where all the data is handled. For small values of dwNtbOutMaxSize the memory allocated during alloc_skb(dwNtbOutMaxSize, GFP_ATOMIC) will have the same size, due to how size is aligned at alloc time: size = SKB_DATA_ALIGN(size); size += SKB_DATA_ALIGN(sizeof(struct skb_shared_info)); Thus we hit the same bug that we tried to squash with commit 2be6d4d16a084 ("net: cdc_ncm: Allow for dwNtbOutMaxSize to be unset or zero") Low values of dwNtbOutMaxSize do not cause an issue presently because at alloc_skb() time more memory (512b) is allocated than required for the SKB headers alone (320b), leaving some space (512b - 320b = 192b) for CDC data (172b). However, if more elements (for example 3 x u64 = [24b]) were added to one of the SKB header structs, say 'struct skb_shared_info', increasing its original size (320b [320b aligned]) to something larger (344b [384b aligned]), then suddenly the CDC data (172b) no longer fits in the spare SKB data area (512b - 384b = 128b). Consequently the SKB bounds checking semantics fails and panics: skbuff: skb_over_panic: text:ffffffff831f755b len:184 put:172 head:ffff88811f1c6c00 data:ffff88811f1c6c00 tail:0xb8 end:0x80 dev:<NULL> ------------[ cut here ]------------ kernel BUG at net/core/skbuff.c:113! invalid opcode: 0000 [#1] PREEMPT SMP KASAN CPU: 0 PID: 57 Comm: kworker/0:2 Not tainted 5.15.106-syzkaller-00249-g19c0ed55a470 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/14/2023 Workqueue: mld mld_ifc_work RIP: 0010:skb_panic net/core/skbuff.c:113 [inline] RIP: 0010:skb_over_panic+0x14c/0x150 net/core/skbuff.c:118 [snip] Call Trace: <TASK> skb_put+0x151/0x210 net/core/skbuff.c:2047 skb_put_zero include/linux/skbuff.h:2422 [inline] cdc_ncm_ndp16 drivers/net/usb/cdc_ncm.c:1131 [inline] cdc_ncm_fill_tx_frame+0x11ab/0x3da0 drivers/net/usb/cdc_ncm.c:1308 cdc_ncm_tx_fixup+0xa3/0x100 Deal with too low values of dwNtbOutMaxSize, clamp it in the range [USB_CDC_NCM_NTB_MIN_OUT_SIZE, CDC_NCM_NTB_MAX_SIZE_TX]. We ensure enough data space is allocated to handle CDC data by making sure dwNtbOutMaxSize is not smaller than USB_CDC_NCM_NTB_MIN_OUT_SIZE.

In the Linux kernel, the following vulnerability has been resolved: media: qcom: camss: fix error path on configuration of power domains There is a chance to meet runtime issues during configuration of CAMSS power domains, because on the error path dev_pm_domain_detach() is unexpectedly called with NULL or error pointer. One of the simplest ways to reproduce the problem is to probe CAMSS driver before registration of CAMSS power domains, for instance if a platform CAMCC driver is simply not built. Warning backtrace example: Unable to handle kernel NULL pointer dereference at virtual address 00000000000001a2 <snip> pc : dev_pm_domain_detach+0x8/0x48 lr : camss_probe+0x374/0x9c0 <snip> Call trace: dev_pm_domain_detach+0x8/0x48 platform_probe+0x70/0xf0 really_probe+0xc4/0x2a8 __driver_probe_device+0x80/0x140 driver_probe_device+0x48/0x170 __device_attach_driver+0xc0/0x148 bus_for_each_drv+0x88/0xf0 __device_attach+0xb0/0x1c0 device_initial_probe+0x1c/0x30 bus_probe_device+0xb4/0xc0 deferred_probe_work_func+0x90/0xd0 process_one_work+0x164/0x3e0 worker_thread+0x310/0x420 kthread+0x120/0x130 ret_from_fork+0x10/0x20

In the Linux kernel, the following vulnerability has been resolved: Drivers: hv: util: Avoid accessing a ringbuffer not initialized yet If the KVP (or VSS) daemon starts before the VMBus channel's ringbuffer is fully initialized, we can hit the panic below: hv_utils: Registering HyperV Utility Driver hv_vmbus: registering driver hv_utils ... BUG: kernel NULL pointer dereference, address: 0000000000000000 CPU: 44 UID: 0 PID: 2552 Comm: hv_kvp_daemon Tainted: G E 6.11.0-rc3+ #1 RIP: 0010:hv_pkt_iter_first+0x12/0xd0 Call Trace: ... vmbus_recvpacket hv_kvp_onchannelcallback vmbus_on_event tasklet_action_common tasklet_action handle_softirqs irq_exit_rcu sysvec_hyperv_stimer0 </IRQ> <TASK> asm_sysvec_hyperv_stimer0 ... kvp_register_done hvt_op_read vfs_read ksys_read __x64_sys_read This can happen because the KVP/VSS channel callback can be invoked even before the channel is fully opened: 1) as soon as hv_kvp_init() -> hvutil_transport_init() creates /dev/vmbus/hv_kvp, the kvp daemon can open the device file immediately and register itself to the driver by writing a message KVP_OP_REGISTER1 to the file (which is handled by kvp_on_msg() ->kvp_handle_handshake()) and reading the file for the driver's response, which is handled by hvt_op_read(), which calls hvt->on_read(), i.e. kvp_register_done(). 2) the problem with kvp_register_done() is that it can cause the channel callback to be called even before the channel is fully opened, and when the channel callback is starting to run, util_probe()-> vmbus_open() may have not initialized the ringbuffer yet, so the callback can hit the panic of NULL pointer dereference. To reproduce the panic consistently, we can add a "ssleep(10)" for KVP in __vmbus_open(), just before the first hv_ringbuffer_init(), and then we unload and reload the driver hv_utils, and run the daemon manually within the 10 seconds. Fix the panic by reordering the steps in util_probe() so the char dev entry used by the KVP or VSS daemon is not created until after vmbus_open() has completed. This reordering prevents the race condition from happening.

In the Linux kernel, the following vulnerability has been resolved: virtio_pci: Fix admin vq cleanup by using correct info pointer vp_modern_avq_cleanup() and vp_del_vqs() clean up admin vq resources by virtio_pci_vq_info pointer. The info pointer of admin vq is stored in vp_dev->admin_vq.info instead of vp_dev->vqs[]. Using the info pointer from vp_dev->vqs[] for admin vq causes a kernel NULL pointer dereference bug. In vp_modern_avq_cleanup() and vp_del_vqs(), get the info pointer from vp_dev->admin_vq.info for admin vq to clean up the resources. Also make info ptr as argument of vp_del_vq() to be symmetric with vp_setup_vq(). vp_reset calls vp_modern_avq_cleanup, and causes the Call Trace: ================================================================== BUG: kernel NULL pointer dereference, address:0000000000000000 ... CPU: 49 UID: 0 PID: 4439 Comm: modprobe Not tainted 6.11.0-rc5 #1 RIP: 0010:vp_reset+0x57/0x90 [virtio_pci] Call Trace: <TASK> ... ? vp_reset+0x57/0x90 [virtio_pci] ? vp_reset+0x38/0x90 [virtio_pci] virtio_reset_device+0x1d/0x30 remove_vq_common+0x1c/0x1a0 [virtio_net] virtnet_remove+0xa1/0xc0 [virtio_net] virtio_dev_remove+0x46/0xa0 ... virtio_pci_driver_exit+0x14/0x810 [virtio_pci] ==================================================================

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: btmtk: adjust the position to init iso data anchor MediaTek iso data anchor init should be moved to where MediaTek claims iso data interface. If there is an unexpected BT usb disconnect during setup flow, it will cause a NULL pointer crash issue when releasing iso anchor since the anchor wasn't been init yet. Adjust the position to do iso data anchor init. [ 17.137991] pc : usb_kill_anchored_urbs+0x60/0x168 [ 17.137998] lr : usb_kill_anchored_urbs+0x44/0x168 [ 17.137999] sp : ffffffc0890cb5f0 [ 17.138000] x29: ffffffc0890cb5f0 x28: ffffff80bb6c2e80 [ 17.144081] gpio gpiochip0: registered chardev handle for 1 lines [ 17.148421] x27: 0000000000000000 [ 17.148422] x26: ffffffd301ff4298 x25: 0000000000000003 x24: 00000000000000f0 [ 17.148424] x23: 0000000000000000 x22: 00000000ffffffff x21: 0000000000000001 [ 17.148425] x20: ffffffffffffffd8 x19: ffffff80c0f25560 x18: 0000000000000000 [ 17.148427] x17: ffffffd33864e408 x16: ffffffd33808f7c8 x15: 0000000000200000 [ 17.232789] x14: e0cd73cf80ffffff x13: 50f2137c0a0338c9 x12: 0000000000000001 [ 17.239912] x11: 0000000080150011 x10: 0000000000000002 x9 : 0000000000000001 [ 17.247035] x8 : 0000000000000000 x7 : 0000000000008080 x6 : 8080000000000000 [ 17.254158] x5 : ffffffd33808ebc0 x4 : fffffffe033dcf20 x3 : 0000000080150011 [ 17.261281] x2 : ffffff8087a91400 x1 : 0000000000000000 x0 : ffffff80c0f25588 [ 17.268404] Call trace: [ 17.270841] usb_kill_anchored_urbs+0x60/0x168 [ 17.275274] btusb_mtk_release_iso_intf+0x2c/0xd8 [btusb (HASH:5afe 6)] [ 17.284226] btusb_mtk_disconnect+0x14/0x28 [btusb (HASH:5afe 6)] [ 17.292652] btusb_disconnect+0x70/0x140 [btusb (HASH:5afe 6)] [ 17.300818] usb_unbind_interface+0xc4/0x240 [ 17.305079] device_release_driver_internal+0x18c/0x258 [ 17.310296] device_release_driver+0x1c/0x30 [ 17.314557] bus_remove_device+0x140/0x160 [ 17.318643] device_del+0x1c0/0x330 [ 17.322121] usb_disable_device+0x80/0x180 [ 17.326207] usb_disconnect+0xec/0x300 [ 17.329948] hub_quiesce+0x80/0xd0 [ 17.333339] hub_disconnect+0x44/0x190 [ 17.337078] usb_unbind_interface+0xc4/0x240 [ 17.341337] device_release_driver_internal+0x18c/0x258 [ 17.346551] device_release_driver+0x1c/0x30 [ 17.350810] usb_driver_release_interface+0x70/0x88 [ 17.355677] proc_ioctl+0x13c/0x228 [ 17.359157] proc_ioctl_default+0x50/0x80 [ 17.363155] usbdev_ioctl+0x830/0xd08 [ 17.366808] __arm64_sys_ioctl+0x94/0xd0 [ 17.370723] invoke_syscall+0x6c/0xf8 [ 17.374377] el0_svc_common+0x84/0xe0 [ 17.378030] do_el0_svc+0x20/0x30 [ 17.381334] el0_svc+0x34/0x60 [ 17.384382] el0t_64_sync_handler+0x88/0xf0 [ 17.388554] el0t_64_sync+0x180/0x188 [ 17.392208] Code: f9400677 f100a2f4 54fffea0 d503201f (b8350288) [ 17.398289] ---[ end trace 0000000000000000 ]---

In the Linux kernel, the following vulnerability has been resolved: cpufreq: CPPC: Fix possible null-ptr-deref for cppc_get_cpu_cost() cpufreq_cpu_get_raw() may return NULL if the cpu is not in policy->cpus cpu mask and it will cause null pointer dereference, so check NULL for cppc_get_cpu_cost().

In the Linux kernel, the following vulnerability has been resolved: phy: realtek: usb: fix NULL deref in rtk_usb3phy_probe In rtk_usb3phy_probe() devm_kzalloc() may return NULL but this returned value is not checked.

In the Linux kernel, the following vulnerability has been resolved: mm: fix NULL pointer dereference in alloc_pages_bulk_noprof We triggered a NULL pointer dereference for ac.preferred_zoneref->zone in alloc_pages_bulk_noprof() when the task is migrated between cpusets. When cpuset is enabled, in prepare_alloc_pages(), ac->nodemask may be &current->mems_allowed. when first_zones_zonelist() is called to find preferred_zoneref, the ac->nodemask may be modified concurrently if the task is migrated between different cpusets. Assuming we have 2 NUMA Node, when traversing Node1 in ac->zonelist, the nodemask is 2, and when traversing Node2 in ac->zonelist, the nodemask is 1. As a result, the ac->preferred_zoneref points to NULL zone. In alloc_pages_bulk_noprof(), for_each_zone_zonelist_nodemask() finds a allowable zone and calls zonelist_node_idx(ac.preferred_zoneref), leading to NULL pointer dereference. __alloc_pages_noprof() fixes this issue by checking NULL pointer in commit ea57485af8f4 ("mm, page_alloc: fix check for NULL preferred_zone") and commit df76cee6bbeb ("mm, page_alloc: remove redundant checks from alloc fastpath"). To fix it, check NULL pointer for preferred_zoneref->zone.

In the Linux kernel, the following vulnerability has been resolved: drm/rockchip: vop: Fix a dereferenced before check warning The 'state' can't be NULL, we should check crtc_state. Fix warning: drivers/gpu/drm/rockchip/rockchip_drm_vop.c:1096 vop_plane_atomic_async_check() warn: variable dereferenced before check 'state' (see line 1077)

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: CT: Fix null-ptr-deref in add rule err flow In error flow of mlx5_tc_ct_entry_add_rule(), in case ct_rule_add() callback returns error, zone_rule->attr is used uninitiated. Fix it to use attr which has the needed pointer value. Kernel log: BUG: kernel NULL pointer dereference, address: 0000000000000110 RIP: 0010:mlx5_tc_ct_entry_add_rule+0x2b1/0x2f0 [mlx5_core] … Call Trace: <TASK> ? __die+0x20/0x70 ? page_fault_oops+0x150/0x3e0 ? exc_page_fault+0x74/0x140 ? asm_exc_page_fault+0x22/0x30 ? mlx5_tc_ct_entry_add_rule+0x2b1/0x2f0 [mlx5_core] ? mlx5_tc_ct_entry_add_rule+0x1d5/0x2f0 [mlx5_core] mlx5_tc_ct_block_flow_offload+0xc6a/0xf90 [mlx5_core] ? nf_flow_offload_tuple+0xd8/0x190 [nf_flow_table] nf_flow_offload_tuple+0xd8/0x190 [nf_flow_table] flow_offload_work_handler+0x142/0x320 [nf_flow_table] ? finish_task_switch.isra.0+0x15b/0x2b0 process_one_work+0x16c/0x320 worker_thread+0x28c/0x3a0 ? __pfx_worker_thread+0x10/0x10 kthread+0xb8/0xf0 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2d/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK>

In the Linux kernel, the following vulnerability has been resolved: drm/i915/gt: Check set_default_submission() before deferencing When the i915 driver firmware binaries are not present, the set_default_submission pointer is not set. This pointer is dereferenced during suspend anyways. Add a check to make sure it is set before dereferencing. [ 23.289926] PM: suspend entry (deep) [ 23.293558] Filesystems sync: 0.000 seconds [ 23.298010] Freezing user space processes [ 23.302771] Freezing user space processes completed (elapsed 0.000 seconds) [ 23.309766] OOM killer disabled. [ 23.313027] Freezing remaining freezable tasks [ 23.318540] Freezing remaining freezable tasks completed (elapsed 0.001 seconds) [ 23.342038] serial 00:05: disabled [ 23.345719] serial 00:02: disabled [ 23.349342] serial 00:01: disabled [ 23.353782] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 23.358993] sd 1:0:0:0: [sdb] Synchronizing SCSI cache [ 23.361635] ata1.00: Entering standby power mode [ 23.368863] ata2.00: Entering standby power mode [ 23.445187] BUG: kernel NULL pointer dereference, address: 0000000000000000 [ 23.452194] #PF: supervisor instruction fetch in kernel mode [ 23.457896] #PF: error_code(0x0010) - not-present page [ 23.463065] PGD 0 P4D 0 [ 23.465640] Oops: Oops: 0010 [#1] SMP NOPTI [ 23.469869] CPU: 8 UID: 0 PID: 211 Comm: kworker/u48:18 Tainted: G S W 6.19.0-rc4-00020-gf0b9d8eb98df #10 PREEMPT(voluntary) [ 23.482512] Tainted: [S]=CPU_OUT_OF_SPEC, [W]=WARN [ 23.496511] Workqueue: async async_run_entry_fn [ 23.501087] RIP: 0010:0x0 [ 23.503755] Code: Unable to access opcode bytes at 0xffffffffffffffd6. [ 23.510324] RSP: 0018:ffffb4a60065fca8 EFLAGS: 00010246 [ 23.515592] RAX: 0000000000000000 RBX: ffff9f428290e000 RCX: 000000000000000f [ 23.522765] RDX: 0000000000000000 RSI: 0000000000000282 RDI: ffff9f428290e000 [ 23.529937] RBP: ffff9f4282907070 R08: ffff9f4281130428 R09: 00000000ffffffff [ 23.537111] R10: 0000000000000000 R11: 0000000000000001 R12: ffff9f42829070f8 [ 23.544284] R13: ffff9f4282906028 R14: ffff9f4282900000 R15: ffff9f4282906b68 [ 23.551457] FS: 0000000000000000(0000) GS:ffff9f466b2cf000(0000) knlGS:0000000000000000 [ 23.559588] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 23.565365] CR2: ffffffffffffffd6 CR3: 000000031c230001 CR4: 0000000000f70ef0 [ 23.572539] PKRU: 55555554 [ 23.575281] Call Trace: [ 23.577770] <TASK> [ 23.579905] intel_engines_reset_default_submission+0x42/0x60 [ 23.585695] __intel_gt_unset_wedged+0x191/0x200 [ 23.590360] intel_gt_unset_wedged+0x20/0x40 [ 23.594675] gt_sanitize+0x15e/0x170 [ 23.598290] i915_gem_suspend_late+0x6b/0x180 [ 23.602692] i915_drm_suspend_late+0x35/0xf0 [ 23.607008] ? __pfx_pci_pm_suspend_late+0x10/0x10 [ 23.611843] dpm_run_callback+0x78/0x1c0 [ 23.615817] device_suspend_late+0xde/0x2e0 [ 23.620037] async_suspend_late+0x18/0x30 [ 23.624082] async_run_entry_fn+0x25/0xa0 [ 23.628129] process_one_work+0x15b/0x380 [ 23.632182] worker_thread+0x2a5/0x3c0 [ 23.635973] ? __pfx_worker_thread+0x10/0x10 [ 23.640279] kthread+0xf6/0x1f0 [ 23.643464] ? __pfx_kthread+0x10/0x10 [ 23.647263] ? __pfx_kthread+0x10/0x10 [ 23.651045] ret_from_fork+0x131/0x190 [ 23.654837] ? __pfx_kthread+0x10/0x10 [ 23.658634] ret_from_fork_asm+0x1a/0x30 [ 23.662597] </TASK> [ 23.664826] Modules linked in: [ 23.667914] CR2: 0000000000000000 [ 23.671271] ------------[ cut here ]------------ (cherry picked from commit daa199abc3d3d1740c9e3a2c3e9216ae5b447cad)

In the Linux kernel, the following vulnerability has been resolved: drm/msm/dsi: Add missing check for alloc_ordered_workqueue Add check for the return value of alloc_ordered_workqueue as it may return NULL pointer and cause NULL pointer dereference. Patchwork: https://patchwork.freedesktop.org/patch/517646/

In the Linux kernel, the following vulnerability has been resolved: drm/mediatek: Fix potential NULL dereference in mtk_crtc_destroy() In mtk_crtc_create(), if the call to mbox_request_channel() fails then we set the "mtk_crtc->cmdq_client.chan" pointer to NULL. In that situation, we do not call cmdq_pkt_create(). During the cleanup, we need to check if the "mtk_crtc->cmdq_client.chan" is NULL first before calling cmdq_pkt_destroy(). Calling cmdq_pkt_destroy() is unnecessary if we didn't call cmdq_pkt_create() and it will result in a NULL pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix null-ptr-deref in block_touch_buffer tracepoint Patch series "nilfs2: fix null-ptr-deref bugs on block tracepoints". This series fixes null pointer dereference bugs that occur when using nilfs2 and two block-related tracepoints. This patch (of 2): It has been reported that when using "block:block_touch_buffer" tracepoint, touch_buffer() called from __nilfs_get_folio_block() causes a NULL pointer dereference, or a general protection fault when KASAN is enabled. This happens because since the tracepoint was added in touch_buffer(), it references the dev_t member bh->b_bdev->bd_dev regardless of whether the buffer head has a pointer to a block_device structure. In the current implementation, the block_device structure is set after the function returns to the caller. Here, touch_buffer() is used to mark the folio/page that owns the buffer head as accessed, but the common search helper for folio/page used by the caller function was optimized to mark the folio/page as accessed when it was reimplemented a long time ago, eliminating the need to call touch_buffer() here in the first place. So this solves the issue by eliminating the touch_buffer() call itself.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: DR, prevent potential error pointer dereference The dr_domain_add_vport_cap() function generally returns NULL on error but sometimes we want it to return ERR_PTR(-EBUSY) so the caller can retry. The problem here is that "ret" can be either -EBUSY or -ENOMEM and if it's and -ENOMEM then the error pointer is propogated back and eventually dereferenced in dr_ste_v0_build_src_gvmi_qpn_tag().

In the Linux kernel, the following vulnerability has been resolved: erofs: fix file-backed mounts over FUSE syzbot reported a null-ptr-deref in fuse_read_args_fill: fuse_read_folio+0xb0/0x100 fs/fuse/file.c:905 filemap_read_folio+0xc6/0x2a0 mm/filemap.c:2367 do_read_cache_folio+0x263/0x5c0 mm/filemap.c:3825 read_mapping_folio include/linux/pagemap.h:1011 [inline] erofs_bread+0x34d/0x7e0 fs/erofs/data.c:41 erofs_read_superblock fs/erofs/super.c:281 [inline] erofs_fc_fill_super+0x2b9/0x2500 fs/erofs/super.c:625 Unlike most filesystems, some network filesystems and FUSE need unavoidable valid `file` pointers for their read I/Os [1]. Anyway, those use cases need to be supported too. [1] https://docs.kernel.org/filesystems/vfs.html

In the Linux kernel, the following vulnerability has been resolved: clk: clk-apple-nco: Add NULL check in applnco_probe Add NULL check in applnco_probe, to handle kernel NULL pointer dereference error.

In the Linux kernel, the following vulnerability has been resolved: phy: realtek: usb: fix NULL deref in rtk_usb2phy_probe In rtk_usb2phy_probe() devm_kzalloc() may return NULL but this returned value is not checked.

In the Linux kernel, the following vulnerability has been resolved: wifi: rtw89: coex: check NULL return of kmalloc in btc_fw_set_monreg() kmalloc may fail, return value might be NULL and will cause NULL pointer dereference. Add check NULL return of kmalloc in btc_fw_set_monreg().

In the Linux kernel, the following vulnerability has been resolved: drm/mediatek: dp: Only trigger DRM HPD events if bridge is attached The MediaTek DisplayPort interface bridge driver starts its interrupts as soon as its probed. However when the interrupts trigger the bridge might not have been attached to a DRM device. As drm_helper_hpd_irq_event() does not check whether the passed in drm_device is valid or not, a NULL pointer passed in results in a kernel NULL pointer dereference in it. Check whether the bridge is attached and only trigger an HPD event if it is.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix null check for pipe_ctx->plane_state in hwss_setup_dpp This commit addresses a null pointer dereference issue in hwss_setup_dpp(). The issue could occur when pipe_ctx->plane_state is null. The fix adds a check to ensure `pipe_ctx->plane_state` is not null before accessing. This prevents a null pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: idpf: fix idpf_vc_core_init error path In an event where the platform running the device control plane is rebooted, reset is detected on the driver. It releases all the resources and waits for the reset to complete. Once the reset is done, it tries to build the resources back. At this time if the device control plane is not yet started, then the driver timeouts on the virtchnl message and retries to establish the mailbox again. In the retry flow, mailbox is deinitialized but the mailbox workqueue is still alive and polling for the mailbox message. This results in accessing the released control queue leading to null-ptr-deref. Fix it by unrolling the work queue cancellation and mailbox deinitialization in the reverse order which they got initialized.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: prevent NULL pointer dereference if ATIF is not supported acpi_evaluate_object() may return AE_NOT_FOUND (failure), which would result in dereferencing buffer.pointer (obj) while being NULL. Although this case may be unrealistic for the current code, it is still better to protect against possible bugs. Bail out also when status is AE_NOT_FOUND. This fixes 1 FORWARD_NULL issue reported by Coverity Report: CID 1600951: Null pointer dereferences (FORWARD_NULL) (cherry picked from commit 91c9e221fe2553edf2db71627d8453f083de87a1)

In the Linux kernel, the following vulnerability has been resolved: firmware: arm_scpi: Check the DVFS OPP count returned by the firmware Fix a kernel crash with the below call trace when the SCPI firmware returns OPP count of zero. dvfs_info.opp_count may be zero on some platforms during the reboot test, and the kernel will crash after dereferencing the pointer to kcalloc(info->count, sizeof(*opp), GFP_KERNEL). | Unable to handle kernel NULL pointer dereference at virtual address 0000000000000028 | Mem abort info: | ESR = 0x96000004 | Exception class = DABT (current EL), IL = 32 bits | SET = 0, FnV = 0 | EA = 0, S1PTW = 0 | Data abort info: | ISV = 0, ISS = 0x00000004 | CM = 0, WnR = 0 | user pgtable: 4k pages, 48-bit VAs, pgdp = 00000000faefa08c | [0000000000000028] pgd=0000000000000000 | Internal error: Oops: 96000004 [#1] SMP | scpi-hwmon: probe of PHYT000D:00 failed with error -110 | Process systemd-udevd (pid: 1701, stack limit = 0x00000000aaede86c) | CPU: 2 PID: 1701 Comm: systemd-udevd Not tainted 4.19.90+ #1 | Hardware name: PHYTIUM LTD Phytium FT2000/4/Phytium FT2000/4, BIOS | pstate: 60000005 (nZCv daif -PAN -UAO) | pc : scpi_dvfs_recalc_rate+0x40/0x58 [clk_scpi] | lr : clk_register+0x438/0x720 | Call trace: | scpi_dvfs_recalc_rate+0x40/0x58 [clk_scpi] | devm_clk_hw_register+0x50/0xa0 | scpi_clk_ops_init.isra.2+0xa0/0x138 [clk_scpi] | scpi_clocks_probe+0x528/0x70c [clk_scpi] | platform_drv_probe+0x58/0xa8 | really_probe+0x260/0x3d0 | driver_probe_device+0x12c/0x148 | device_driver_attach+0x74/0x98 | __driver_attach+0xb4/0xe8 | bus_for_each_dev+0x88/0xe0 | driver_attach+0x30/0x40 | bus_add_driver+0x178/0x2b0 | driver_register+0x64/0x118 | __platform_driver_register+0x54/0x60 | scpi_clocks_driver_init+0x24/0x1000 [clk_scpi] | do_one_initcall+0x54/0x220 | do_init_module+0x54/0x1c8 | load_module+0x14a4/0x1668 | __se_sys_finit_module+0xf8/0x110 | __arm64_sys_finit_module+0x24/0x30 | el0_svc_common+0x78/0x170 | el0_svc_handler+0x38/0x78 | el0_svc+0x8/0x340 | Code: 937d7c00 a94153f3 a8c27bfd f9400421 (b8606820) | ---[ end trace 06feb22469d89fa8 ]--- | Kernel panic - not syncing: Fatal exception | SMP: stopping secondary CPUs | Kernel Offset: disabled | CPU features: 0x10,a0002008 | Memory Limit: none