In the Linux kernel, the following vulnerability has been resolved: drm/i915/gt: Use spin_lock_irqsave() in interruptible context spin_lock/unlock() functions used in interrupt contexts could result in a deadlock, as seen in GitLab issue #13399, which occurs when interrupt comes in while holding a lock. Try to remedy the problem by saving irq state before spin lock acquisition. v2: add irqs' state save/restore calls to all locks/unlocks in signal_irq_work() execution (Maciej) v3: use with spin_lock_irqsave() in guc_lrc_desc_unpin() instead of other lock/unlock calls and add Fixes and Cc tags (Tvrtko); change title and commit message (cherry picked from commit c088387ddd6482b40f21ccf23db1125e8fa4af7e)

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: iso: Fix circular lock in iso_conn_big_sync This fixes the circular locking dependency warning below, by reworking iso_sock_recvmsg, to ensure that the socket lock is always released before calling a function that locks hdev. [ 561.670344] ====================================================== [ 561.670346] WARNING: possible circular locking dependency detected [ 561.670349] 6.12.0-rc6+ #26 Not tainted [ 561.670351] ------------------------------------------------------ [ 561.670353] iso-tester/3289 is trying to acquire lock: [ 561.670355] ffff88811f600078 (&hdev->lock){+.+.}-{3:3}, at: iso_conn_big_sync+0x73/0x260 [bluetooth] [ 561.670405] but task is already holding lock: [ 561.670407] ffff88815af58258 (sk_lock-AF_BLUETOOTH){+.+.}-{0:0}, at: iso_sock_recvmsg+0xbf/0x500 [bluetooth] [ 561.670450] which lock already depends on the new lock. [ 561.670452] the existing dependency chain (in reverse order) is: [ 561.670453] -> #2 (sk_lock-AF_BLUETOOTH){+.+.}-{0:0}: [ 561.670458] lock_acquire+0x7c/0xc0 [ 561.670463] lock_sock_nested+0x3b/0xf0 [ 561.670467] bt_accept_dequeue+0x1a5/0x4d0 [bluetooth] [ 561.670510] iso_sock_accept+0x271/0x830 [bluetooth] [ 561.670547] do_accept+0x3dd/0x610 [ 561.670550] __sys_accept4+0xd8/0x170 [ 561.670553] __x64_sys_accept+0x74/0xc0 [ 561.670556] x64_sys_call+0x17d6/0x25f0 [ 561.670559] do_syscall_64+0x87/0x150 [ 561.670563] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 561.670567] -> #1 (sk_lock-AF_BLUETOOTH-BTPROTO_ISO){+.+.}-{0:0}: [ 561.670571] lock_acquire+0x7c/0xc0 [ 561.670574] lock_sock_nested+0x3b/0xf0 [ 561.670577] iso_sock_listen+0x2de/0xf30 [bluetooth] [ 561.670617] __sys_listen_socket+0xef/0x130 [ 561.670620] __x64_sys_listen+0xe1/0x190 [ 561.670623] x64_sys_call+0x2517/0x25f0 [ 561.670626] do_syscall_64+0x87/0x150 [ 561.670629] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 561.670632] -> #0 (&hdev->lock){+.+.}-{3:3}: [ 561.670636] __lock_acquire+0x32ad/0x6ab0 [ 561.670639] lock_acquire.part.0+0x118/0x360 [ 561.670642] lock_acquire+0x7c/0xc0 [ 561.670644] __mutex_lock+0x18d/0x12f0 [ 561.670647] mutex_lock_nested+0x1b/0x30 [ 561.670651] iso_conn_big_sync+0x73/0x260 [bluetooth] [ 561.670687] iso_sock_recvmsg+0x3e9/0x500 [bluetooth] [ 561.670722] sock_recvmsg+0x1d5/0x240 [ 561.670725] sock_read_iter+0x27d/0x470 [ 561.670727] vfs_read+0x9a0/0xd30 [ 561.670731] ksys_read+0x1a8/0x250 [ 561.670733] __x64_sys_read+0x72/0xc0 [ 561.670736] x64_sys_call+0x1b12/0x25f0 [ 561.670738] do_syscall_64+0x87/0x150 [ 561.670741] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 561.670744] other info that might help us debug this: [ 561.670745] Chain exists of: &hdev->lock --> sk_lock-AF_BLUETOOTH-BTPROTO_ISO --> sk_lock-AF_BLUETOOTH [ 561.670751] Possible unsafe locking scenario: [ 561.670753] CPU0 CPU1 [ 561.670754] ---- ---- [ 561.670756] lock(sk_lock-AF_BLUETOOTH); [ 561.670758] lock(sk_lock AF_BLUETOOTH-BTPROTO_ISO); [ 561.670761] lock(sk_lock-AF_BLUETOOTH); [ 561.670764] lock(&hdev->lock); [ 561.670767] *** DEADLOCK ***

In the Linux kernel, the following vulnerability has been resolved: tty: xilinx_uartps: split sysrq handling lockdep detects the following circular locking dependency: CPU 0 CPU 1 ========================== ============================ cdns_uart_isr() printk() uart_port_lock(port) console_lock() cdns_uart_console_write() if (!port->sysrq) uart_port_lock(port) uart_handle_break() port->sysrq = ... uart_handle_sysrq_char() printk() console_lock() The fixed commit attempts to avoid this situation by only taking the port lock in cdns_uart_console_write if port->sysrq unset. However, if (as shown above) cdns_uart_console_write runs before port->sysrq is set, then it will try to take the port lock anyway. This may result in a deadlock. Fix this by splitting sysrq handling into two parts. We use the prepare helper under the port lock and defer handling until we release the lock.

In the Linux kernel, the following vulnerability has been resolved: ntfs3: fix circular locking dependency in run_unpack_ex Syzbot reported a circular locking dependency between wnd->rw_lock (sbi->used.bitmap) and ni->file.run_lock. The deadlock scenario: 1. ntfs_extend_mft() takes ni->file.run_lock then wnd->rw_lock. 2. run_unpack_ex() takes wnd->rw_lock then tries to acquire ni->file.run_lock inside ntfs_refresh_zone(). This creates an AB-BA deadlock. Fix this by using down_read_trylock() instead of down_read() when acquiring run_lock in run_unpack_ex(). If the lock is contended, skip ntfs_refresh_zone() - the MFT zone will be refreshed on the next MFT operation. This breaks the circular dependency since we never block waiting for run_lock while holding wnd->rw_lock.

In the Linux kernel, the following vulnerability has been resolved: net: rose: lock the socket in rose_bind() syzbot reported a soft lockup in rose_loopback_timer(), with a repro calling bind() from multiple threads. rose_bind() must lock the socket to avoid this issue.

In the Linux kernel, the following vulnerability has been resolved: afs: Fix merge preference rule failure condition syzbot reported a lock held when returning to userspace[1]. This is because if argc is less than 0 and the function returns directly, the held inode lock is not released. Fix this by store the error in ret and jump to done to clean up instead of returning directly. [dh: Modified Lizhi Xu's original patch to make it honour the error code from afs_split_string()] [1] WARNING: lock held when returning to user space! 6.13.0-rc3-syzkaller-00209-g499551201b5f #0 Not tainted ------------------------------------------------ syz-executor133/5823 is leaving the kernel with locks still held! 1 lock held by syz-executor133/5823: #0: ffff888071cffc00 (&sb->s_type->i_mutex_key#9){++++}-{4:4}, at: inode_lock include/linux/fs.h:818 [inline] #0: ffff888071cffc00 (&sb->s_type->i_mutex_key#9){++++}-{4:4}, at: afs_proc_addr_prefs_write+0x2bb/0x14e0 fs/afs/addr_prefs.c:388

In the Linux kernel, the following vulnerability has been resolved: block: fix queue freeze vs limits lock order in sysfs store methods queue_attr_store() always freezes a device queue before calling the attribute store operation. For attributes that control queue limits, the store operation will also lock the queue limits with a call to queue_limits_start_update(). However, some drivers (e.g. SCSI sd) may need to issue commands to a device to obtain limit values from the hardware with the queue limits locked. This creates a potential ABBA deadlock situation if a user attempts to modify a limit (thus freezing the device queue) while the device driver starts a revalidation of the device queue limits. Avoid such deadlock by not freezing the queue before calling the ->store_limit() method in struct queue_sysfs_entry and instead use the queue_limits_commit_update_frozen helper to freeze the queue after taking the limits lock. This also removes taking the sysfs lock for the store_limit method as it doesn't protect anything here, but creates even more nesting. Hopefully it will go away from the actual sysfs methods entirely soon. (commit log adapted from a similar patch from Damien Le Moal)

In the Linux kernel, the following vulnerability has been resolved: clocksource: Use migrate_disable() to avoid calling get_random_u32() in atomic context The following bug report happened with a PREEMPT_RT kernel: BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48 in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 2012, name: kwatchdog preempt_count: 1, expected: 0 RCU nest depth: 0, expected: 0 get_random_u32+0x4f/0x110 clocksource_verify_choose_cpus+0xab/0x1a0 clocksource_verify_percpu.part.0+0x6b/0x330 clocksource_watchdog_kthread+0x193/0x1a0 It is due to the fact that clocksource_verify_choose_cpus() is invoked with preemption disabled. This function invokes get_random_u32() to obtain random numbers for choosing CPUs. The batched_entropy_32 local lock and/or the base_crng.lock spinlock in driver/char/random.c will be acquired during the call. In PREEMPT_RT kernel, they are both sleeping locks and so cannot be acquired in atomic context. Fix this problem by using migrate_disable() to allow smp_processor_id() to be reliably used without introducing atomic context. preempt_disable() is then called after clocksource_verify_choose_cpus() but before the clocksource measurement is being run to avoid introducing unexpected latency.

In the Linux kernel, the following vulnerability has been resolved: ocfs2: Avoid touching renamed directory if parent does not change The VFS will not be locking moved directory if its parent does not change. Change ocfs2 rename code to avoid touching renamed directory if its parent does not change as without locking that can corrupt the filesystem.

In the Linux kernel, the following vulnerability has been resolved: IB/ipoib: Fix mcast list locking Releasing the `priv->lock` while iterating the `priv->multicast_list` in `ipoib_mcast_join_task()` opens a window for `ipoib_mcast_dev_flush()` to remove the items while in the middle of iteration. If the mcast is removed while the lock was dropped, the for loop spins forever resulting in a hard lockup (as was reported on RHEL 4.18.0-372.75.1.el8_6 kernel): Task A (kworker/u72:2 below) | Task B (kworker/u72:0 below) -----------------------------------+----------------------------------- ipoib_mcast_join_task(work) | ipoib_ib_dev_flush_light(work) spin_lock_irq(&priv->lock) | __ipoib_ib_dev_flush(priv, ...) list_for_each_entry(mcast, | ipoib_mcast_dev_flush(dev = priv->dev) &priv->multicast_list, list) | ipoib_mcast_join(dev, mcast) | spin_unlock_irq(&priv->lock) | | spin_lock_irqsave(&priv->lock, flags) | list_for_each_entry_safe(mcast, tmcast, | &priv->multicast_list, list) | list_del(&mcast->list); | list_add_tail(&mcast->list, &remove_list) | spin_unlock_irqrestore(&priv->lock, flags) spin_lock_irq(&priv->lock) | | ipoib_mcast_remove_list(&remove_list) (Here, `mcast` is no longer on the | list_for_each_entry_safe(mcast, tmcast, `priv->multicast_list` and we keep | remove_list, list) spinning on the `remove_list` of | >>> wait_for_completion(&mcast->done) the other thread which is blocked | and the list is still valid on | it's stack.) Fix this by keeping the lock held and changing to GFP_ATOMIC to prevent eventual sleeps. Unfortunately we could not reproduce the lockup and confirm this fix but based on the code review I think this fix should address such lockups. crash> bc 31 PID: 747 TASK: ff1c6a1a007e8000 CPU: 31 COMMAND: "kworker/u72:2" -- [exception RIP: ipoib_mcast_join_task+0x1b1] RIP: ffffffffc0944ac1 RSP: ff646f199a8c7e00 RFLAGS: 00000002 RAX: 0000000000000000 RBX: ff1c6a1a04dc82f8 RCX: 0000000000000000 work (&priv->mcast_task{,.work}) RDX: ff1c6a192d60ac68 RSI: 0000000000000286 RDI: ff1c6a1a04dc8000 &mcast->list RBP: ff646f199a8c7e90 R8: ff1c699980019420 R9: ff1c6a1920c9a000 R10: ff646f199a8c7e00 R11: ff1c6a191a7d9800 R12: ff1c6a192d60ac00 mcast R13: ff1c6a1d82200000 R14: ff1c6a1a04dc8000 R15: ff1c6a1a04dc82d8 dev priv (&priv->lock) &priv->multicast_list (aka head) ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 --- <NMI exception stack> --- #5 [ff646f199a8c7e00] ipoib_mcast_join_task+0x1b1 at ffffffffc0944ac1 [ib_ipoib] #6 [ff646f199a8c7e98] process_one_work+0x1a7 at ffffffff9bf10967 crash> rx ff646f199a8c7e68 ff646f199a8c7e68: ff1c6a1a04dc82f8 <<< work = &priv->mcast_task.work crash> list -hO ipoib_dev_priv.multicast_list ff1c6a1a04dc8000 (empty) crash> ipoib_dev_priv.mcast_task.work.func,mcast_mutex.owner.counter ff1c6a1a04dc8000 mcast_task.work.func = 0xffffffffc0944910 <ipoib_mcast_join_task>, mcast_mutex.owner.counter = 0xff1c69998efec000 crash> b 8 PID: 8 TASK: ff1c69998efec000 CPU: 33 COMMAND: "kworker/u72:0" -- #3 [ff646f1980153d50] wait_for_completion+0x96 at ffffffff9c7d7646 #4 [ff646f1980153d90] ipoib_mcast_remove_list+0x56 at ffffffffc0944dc6 [ib_ipoib] #5 [ff646f1980153de8] ipoib_mcast_dev_flush+0x1a7 at ffffffffc09455a7 [ib_ipoib] #6 [ff646f1980153e58] __ipoib_ib_dev_flush+0x1a4 at ffffffffc09431a4 [ib_ipoib] #7 [ff ---truncated---

In the Linux kernel, the following vulnerability has been resolved: net: vlan: don't propagate flags on open With the device instance lock, there is now a possibility of a deadlock: [ 1.211455] ============================================ [ 1.211571] WARNING: possible recursive locking detected [ 1.211687] 6.14.0-rc5-01215-g032756b4ca7a-dirty #5 Not tainted [ 1.211823] -------------------------------------------- [ 1.211936] ip/184 is trying to acquire lock: [ 1.212032] ffff8881024a4c30 (&dev->lock){+.+.}-{4:4}, at: dev_set_allmulti+0x4e/0xb0 [ 1.212207] [ 1.212207] but task is already holding lock: [ 1.212332] ffff8881024a4c30 (&dev->lock){+.+.}-{4:4}, at: dev_open+0x50/0xb0 [ 1.212487] [ 1.212487] other info that might help us debug this: [ 1.212626] Possible unsafe locking scenario: [ 1.212626] [ 1.212751] CPU0 [ 1.212815] ---- [ 1.212871] lock(&dev->lock); [ 1.212944] lock(&dev->lock); [ 1.213016] [ 1.213016] *** DEADLOCK *** [ 1.213016] [ 1.213143] May be due to missing lock nesting notation [ 1.213143] [ 1.213294] 3 locks held by ip/184: [ 1.213371] #0: ffffffff838b53e0 (rtnl_mutex){+.+.}-{4:4}, at: rtnl_nets_lock+0x1b/0xa0 [ 1.213543] #1: ffffffff84e5fc70 (&net->rtnl_mutex){+.+.}-{4:4}, at: rtnl_nets_lock+0x37/0xa0 [ 1.213727] #2: ffff8881024a4c30 (&dev->lock){+.+.}-{4:4}, at: dev_open+0x50/0xb0 [ 1.213895] [ 1.213895] stack backtrace: [ 1.213991] CPU: 0 UID: 0 PID: 184 Comm: ip Not tainted 6.14.0-rc5-01215-g032756b4ca7a-dirty #5 [ 1.213993] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.16.3-1-1 04/01/2014 [ 1.213994] Call Trace: [ 1.213995] <TASK> [ 1.213996] dump_stack_lvl+0x8e/0xd0 [ 1.214000] print_deadlock_bug+0x28b/0x2a0 [ 1.214020] lock_acquire+0xea/0x2a0 [ 1.214027] __mutex_lock+0xbf/0xd40 [ 1.214038] dev_set_allmulti+0x4e/0xb0 # real_dev->flags & IFF_ALLMULTI [ 1.214040] vlan_dev_open+0xa5/0x170 # ndo_open on vlandev [ 1.214042] __dev_open+0x145/0x270 [ 1.214046] __dev_change_flags+0xb0/0x1e0 [ 1.214051] netif_change_flags+0x22/0x60 # IFF_UP vlandev [ 1.214053] dev_change_flags+0x61/0xb0 # for each device in group from dev->vlan_info [ 1.214055] vlan_device_event+0x766/0x7c0 # on netdevsim0 [ 1.214058] notifier_call_chain+0x78/0x120 [ 1.214062] netif_open+0x6d/0x90 [ 1.214064] dev_open+0x5b/0xb0 # locks netdevsim0 [ 1.214066] bond_enslave+0x64c/0x1230 [ 1.214075] do_set_master+0x175/0x1e0 # on netdevsim0 [ 1.214077] do_setlink+0x516/0x13b0 [ 1.214094] rtnl_newlink+0xaba/0xb80 [ 1.214132] rtnetlink_rcv_msg+0x440/0x490 [ 1.214144] netlink_rcv_skb+0xeb/0x120 [ 1.214150] netlink_unicast+0x1f9/0x320 [ 1.214153] netlink_sendmsg+0x346/0x3f0 [ 1.214157] __sock_sendmsg+0x86/0xb0 [ 1.214160] ____sys_sendmsg+0x1c8/0x220 [ 1.214164] ___sys_sendmsg+0x28f/0x2d0 [ 1.214179] __x64_sys_sendmsg+0xef/0x140 [ 1.214184] do_syscall_64+0xec/0x1d0 [ 1.214190] entry_SYSCALL_64_after_hwframe+0x77/0x7f [ 1.214191] RIP: 0033:0x7f2d1b4a7e56 Device setup: netdevsim0 (down) ^ ^ bond netdevsim1.100@netdevsim1 allmulticast=on (down) When we enslave the lower device (netdevsim0) which has a vlan, we propagate vlan's allmuti/promisc flags during ndo_open. This causes (re)locking on of the real_dev. Propagate allmulti/promisc on flags change, not on the open. There is a slight semantics change that vlans that are down now propagate the flags, but this seems unlikely to result in the real issues. Reproducer: echo 0 1 > /sys/bus/netdevsim/new_device dev_path=$(ls -d /sys/bus/netdevsim/devices/netdevsim0/net/*) dev=$(echo $dev_path | rev | cut -d/ -f1 | rev) ip link set dev $dev name netdevsim0 ip link set dev netdevsim0 up ip link add link netdevsim0 name netdevsim0.100 type vlan id 100 ip link set dev netdevsim0.100 allm ---truncated---

In the Linux kernel, the following vulnerability has been resolved: ice: fix LAG and VF lock dependency in ice_reset_vf() 9f74a3dfcf83 ("ice: Fix VF Reset paths when interface in a failed over aggregate"), the ice driver has acquired the LAG mutex in ice_reset_vf(). The commit placed this lock acquisition just prior to the acquisition of the VF configuration lock. If ice_reset_vf() acquires the configuration lock via the ICE_VF_RESET_LOCK flag, this could deadlock with ice_vc_cfg_qs_msg() because it always acquires the locks in the order of the VF configuration lock and then the LAG mutex. Lockdep reports this violation almost immediately on creating and then removing 2 VF: ====================================================== WARNING: possible circular locking dependency detected 6.8.0-rc6 #54 Tainted: G W O ------------------------------------------------------ kworker/60:3/6771 is trying to acquire lock: ff40d43e099380a0 (&vf->cfg_lock){+.+.}-{3:3}, at: ice_reset_vf+0x22f/0x4d0 [ice] but task is already holding lock: ff40d43ea1961210 (&pf->lag_mutex){+.+.}-{3:3}, at: ice_reset_vf+0xb7/0x4d0 [ice] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&pf->lag_mutex){+.+.}-{3:3}: __lock_acquire+0x4f8/0xb40 lock_acquire+0xd4/0x2d0 __mutex_lock+0x9b/0xbf0 ice_vc_cfg_qs_msg+0x45/0x690 [ice] ice_vc_process_vf_msg+0x4f5/0x870 [ice] __ice_clean_ctrlq+0x2b5/0x600 [ice] ice_service_task+0x2c9/0x480 [ice] process_one_work+0x1e9/0x4d0 worker_thread+0x1e1/0x3d0 kthread+0x104/0x140 ret_from_fork+0x31/0x50 ret_from_fork_asm+0x1b/0x30 -> #0 (&vf->cfg_lock){+.+.}-{3:3}: check_prev_add+0xe2/0xc50 validate_chain+0x558/0x800 __lock_acquire+0x4f8/0xb40 lock_acquire+0xd4/0x2d0 __mutex_lock+0x9b/0xbf0 ice_reset_vf+0x22f/0x4d0 [ice] ice_process_vflr_event+0x98/0xd0 [ice] ice_service_task+0x1cc/0x480 [ice] process_one_work+0x1e9/0x4d0 worker_thread+0x1e1/0x3d0 kthread+0x104/0x140 ret_from_fork+0x31/0x50 ret_from_fork_asm+0x1b/0x30 other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&pf->lag_mutex); lock(&vf->cfg_lock); lock(&pf->lag_mutex); lock(&vf->cfg_lock); *** DEADLOCK *** 4 locks held by kworker/60:3/6771: #0: ff40d43e05428b38 ((wq_completion)ice){+.+.}-{0:0}, at: process_one_work+0x176/0x4d0 #1: ff50d06e05197e58 ((work_completion)(&pf->serv_task)){+.+.}-{0:0}, at: process_one_work+0x176/0x4d0 #2: ff40d43ea1960e50 (&pf->vfs.table_lock){+.+.}-{3:3}, at: ice_process_vflr_event+0x48/0xd0 [ice] #3: ff40d43ea1961210 (&pf->lag_mutex){+.+.}-{3:3}, at: ice_reset_vf+0xb7/0x4d0 [ice] stack backtrace: CPU: 60 PID: 6771 Comm: kworker/60:3 Tainted: G W O 6.8.0-rc6 #54 Hardware name: Workqueue: ice ice_service_task [ice] Call Trace: <TASK> dump_stack_lvl+0x4a/0x80 check_noncircular+0x12d/0x150 check_prev_add+0xe2/0xc50 ? save_trace+0x59/0x230 ? add_chain_cache+0x109/0x450 validate_chain+0x558/0x800 __lock_acquire+0x4f8/0xb40 ? lockdep_hardirqs_on+0x7d/0x100 lock_acquire+0xd4/0x2d0 ? ice_reset_vf+0x22f/0x4d0 [ice] ? lock_is_held_type+0xc7/0x120 __mutex_lock+0x9b/0xbf0 ? ice_reset_vf+0x22f/0x4d0 [ice] ? ice_reset_vf+0x22f/0x4d0 [ice] ? rcu_is_watching+0x11/0x50 ? ice_reset_vf+0x22f/0x4d0 [ice] ice_reset_vf+0x22f/0x4d0 [ice] ? process_one_work+0x176/0x4d0 ice_process_vflr_event+0x98/0xd0 [ice] ice_service_task+0x1cc/0x480 [ice] process_one_work+0x1e9/0x4d0 worker_thread+0x1e1/0x3d0 ? __pfx_worker_thread+0x10/0x10 kthread+0x104/0x140 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x31/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1b/0x30 </TASK> To avoid deadlock, we must acquire the LAG ---truncated---

In the Linux kernel, the following vulnerability has been resolved: hwpoison, memory_hotplug: lock folio before unmap hwpoisoned folio Commit b15c87263a69 ("hwpoison, memory_hotplug: allow hwpoisoned pages to be offlined) add page poison checks in do_migrate_range in order to make offline hwpoisoned page possible by introducing isolate_lru_page and try_to_unmap for hwpoisoned page. However folio lock must be held before calling try_to_unmap. Add it to fix this problem. Warning will be produced if folio is not locked during unmap: ------------[ cut here ]------------ kernel BUG at ./include/linux/swapops.h:400! Internal error: Oops - BUG: 00000000f2000800 [#1] PREEMPT SMP Modules linked in: CPU: 4 UID: 0 PID: 411 Comm: bash Tainted: G W 6.13.0-rc1-00016-g3c434c7ee82a-dirty #41 Tainted: [W]=WARN Hardware name: QEMU QEMU Virtual Machine, BIOS 0.0.0 02/06/2015 pstate: 40400005 (nZcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : try_to_unmap_one+0xb08/0xd3c lr : try_to_unmap_one+0x3dc/0xd3c Call trace: try_to_unmap_one+0xb08/0xd3c (P) try_to_unmap_one+0x3dc/0xd3c (L) rmap_walk_anon+0xdc/0x1f8 rmap_walk+0x3c/0x58 try_to_unmap+0x88/0x90 unmap_poisoned_folio+0x30/0xa8 do_migrate_range+0x4a0/0x568 offline_pages+0x5a4/0x670 memory_block_action+0x17c/0x374 memory_subsys_offline+0x3c/0x78 device_offline+0xa4/0xd0 state_store+0x8c/0xf0 dev_attr_store+0x18/0x2c sysfs_kf_write+0x44/0x54 kernfs_fop_write_iter+0x118/0x1a8 vfs_write+0x3a8/0x4bc ksys_write+0x6c/0xf8 __arm64_sys_write+0x1c/0x28 invoke_syscall+0x44/0x100 el0_svc_common.constprop.0+0x40/0xe0 do_el0_svc+0x1c/0x28 el0_svc+0x30/0xd0 el0t_64_sync_handler+0xc8/0xcc el0t_64_sync+0x198/0x19c Code: f9407be0 b5fff320 d4210000 17ffff97 (d4210000) ---[ end trace 0000000000000000 ]---

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix deadlock in nilfs_count_free_blocks() A semaphore deadlock can occur if nilfs_get_block() detects metadata corruption while locating data blocks and a superblock writeback occurs at the same time: task 1 task 2 ------ ------ * A file operation * nilfs_truncate() nilfs_get_block() down_read(rwsem A) <-- nilfs_bmap_lookup_contig() ... generic_shutdown_super() nilfs_put_super() * Prepare to write superblock * down_write(rwsem B) <-- nilfs_cleanup_super() * Detect b-tree corruption * nilfs_set_log_cursor() nilfs_bmap_convert_error() nilfs_count_free_blocks() __nilfs_error() down_read(rwsem A) <-- nilfs_set_error() down_write(rwsem B) <-- *** DEADLOCK *** Here, nilfs_get_block() readlocks rwsem A (= NILFS_MDT(dat_inode)->mi_sem) and then calls nilfs_bmap_lookup_contig(), but if it fails due to metadata corruption, __nilfs_error() is called from nilfs_bmap_convert_error() inside the lock section. Since __nilfs_error() calls nilfs_set_error() unless the filesystem is read-only and nilfs_set_error() attempts to writelock rwsem B (= nilfs->ns_sem) to write back superblock exclusively, hierarchical lock acquisition occurs in the order rwsem A -> rwsem B. Now, if another task starts updating the superblock, it may writelock rwsem B during the lock sequence above, and can deadlock trying to readlock rwsem A in nilfs_count_free_blocks(). However, there is actually no need to take rwsem A in nilfs_count_free_blocks() because it, within the lock section, only reads a single integer data on a shared struct with nilfs_sufile_get_ncleansegs(). This has been the case after commit aa474a220180 ("nilfs2: add local variable to cache the number of clean segments"), that is, even before this bug was introduced. So, this resolves the deadlock problem by just not taking the semaphore in nilfs_count_free_blocks().

In the Linux kernel, the following vulnerability has been resolved: net: phy: register phy led_triggers during probe to avoid AB-BA deadlock There is an AB-BA deadlock when both LEDS_TRIGGER_NETDEV and LED_TRIGGER_PHY are enabled: [ 1362.049207] [<8054e4b8>] led_trigger_register+0x5c/0x1fc <-- Trying to get lock "triggers_list_lock" via down_write(&triggers_list_lock); [ 1362.054536] [<80662830>] phy_led_triggers_register+0xd0/0x234 [ 1362.060329] [<8065e200>] phy_attach_direct+0x33c/0x40c [ 1362.065489] [<80651fc4>] phylink_fwnode_phy_connect+0x15c/0x23c [ 1362.071480] [<8066ee18>] mtk_open+0x7c/0xba0 [ 1362.075849] [<806d714c>] __dev_open+0x280/0x2b0 [ 1362.080384] [<806d7668>] __dev_change_flags+0x244/0x24c [ 1362.085598] [<806d7698>] dev_change_flags+0x28/0x78 [ 1362.090528] [<807150e4>] dev_ioctl+0x4c0/0x654 <-- Hold lock "rtnl_mutex" by calling rtnl_lock(); [ 1362.094985] [<80694360>] sock_ioctl+0x2f4/0x4e0 [ 1362.099567] [<802e9c4c>] sys_ioctl+0x32c/0xd8c [ 1362.104022] [<80014504>] syscall_common+0x34/0x58 Here LED_TRIGGER_PHY is registering LED triggers during phy_attach while holding RTNL and then taking triggers_list_lock. [ 1362.191101] [<806c2640>] register_netdevice_notifier+0x60/0x168 <-- Trying to get lock "rtnl_mutex" via rtnl_lock(); [ 1362.197073] [<805504ac>] netdev_trig_activate+0x194/0x1e4 [ 1362.202490] [<8054e28c>] led_trigger_set+0x1d4/0x360 <-- Hold lock "triggers_list_lock" by down_read(&triggers_list_lock); [ 1362.207511] [<8054eb38>] led_trigger_write+0xd8/0x14c [ 1362.212566] [<80381d98>] sysfs_kf_bin_write+0x80/0xbc [ 1362.217688] [<8037fcd8>] kernfs_fop_write_iter+0x17c/0x28c [ 1362.223174] [<802cbd70>] vfs_write+0x21c/0x3c4 [ 1362.227712] [<802cc0c4>] ksys_write+0x78/0x12c [ 1362.232164] [<80014504>] syscall_common+0x34/0x58 Here LEDS_TRIGGER_NETDEV is being enabled on an LED. It first takes triggers_list_lock and then RTNL. A classical AB-BA deadlock. phy_led_triggers_registers() does not require the RTNL, it does not make any calls into the network stack which require protection. There is also no requirement the PHY has been attached to a MAC, the triggers only make use of phydev state. This allows the call to phy_led_triggers_registers() to be placed elsewhere. PHY probe() and release() don't hold RTNL, so solving the AB-BA deadlock.

In the Linux kernel, the following vulnerability has been resolved: nvdimm: Fix firmware activation deadlock scenarios Lockdep reports the following deadlock scenarios for CXL root device power-management, device_prepare(), operations, and device_shutdown() operations for 'nd_region' devices: Chain exists of: &nvdimm_region_key --> &nvdimm_bus->reconfig_mutex --> system_transition_mutex Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(system_transition_mutex); lock(&nvdimm_bus->reconfig_mutex); lock(system_transition_mutex); lock(&nvdimm_region_key); Chain exists of: &cxl_nvdimm_bridge_key --> acpi_scan_lock --> &cxl_root_key Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&cxl_root_key); lock(acpi_scan_lock); lock(&cxl_root_key); lock(&cxl_nvdimm_bridge_key); These stem from holding nvdimm_bus_lock() over hibernate_quiet_exec() which walks the entire system device topology taking device_lock() along the way. The nvdimm_bus_lock() is protecting against unregistration, multiple simultaneous ops callers, and preventing activate_show() from racing activate_store(). For the first 2, the lock is redundant. Unregistration already flushes all ops users, and sysfs already prevents multiple threads to be active in an ops handler at the same time. For the last userspace should already be waiting for its last activate_store() to complete, and does not need activate_show() to flush the write side, so this lock usage can be deleted in these attributes.

In the Linux kernel, the following vulnerability has been resolved: RDMA/irdma: Fix sleep from invalid context BUG Taking the qos_mutex to process RoCEv2 QP's on netdev events causes a kernel splat. Fix this by removing the handling for RoCEv2 in irdma_cm_teardown_connections that uses the mutex. This handling is only needed for iWARP to avoid having connections established while the link is down or having connections remain functional after the IP address is removed. BUG: sleeping function called from invalid context at kernel/locking/mutex. Call Trace: kernel: dump_stack+0x66/0x90 kernel: ___might_sleep.cold.92+0x8d/0x9a kernel: mutex_lock+0x1c/0x40 kernel: irdma_cm_teardown_connections+0x28e/0x4d0 [irdma] kernel: ? check_preempt_curr+0x7a/0x90 kernel: ? select_idle_sibling+0x22/0x3c0 kernel: ? select_task_rq_fair+0x94c/0xc90 kernel: ? irdma_exec_cqp_cmd+0xc27/0x17c0 [irdma] kernel: ? __wake_up_common+0x7a/0x190 kernel: irdma_if_notify+0x3cc/0x450 [irdma] kernel: ? sched_clock_cpu+0xc/0xb0 kernel: irdma_inet6addr_event+0xc6/0x150 [irdma]

In the Linux kernel, the following vulnerability has been resolved: driver core: fix potential deadlock in __driver_attach In __driver_attach function, There are also AA deadlock problem, like the commit b232b02bf3c2 ("driver core: fix deadlock in __device_attach"). stack like commit b232b02bf3c2 ("driver core: fix deadlock in __device_attach"). list below: In __driver_attach function, The lock holding logic is as follows: ... __driver_attach if (driver_allows_async_probing(drv)) device_lock(dev) // get lock dev async_schedule_dev(__driver_attach_async_helper, dev); // func async_schedule_node async_schedule_node_domain(func) entry = kzalloc(sizeof(struct async_entry), GFP_ATOMIC); /* when fail or work limit, sync to execute func, but __driver_attach_async_helper will get lock dev as will, which will lead to A-A deadlock. */ if (!entry || atomic_read(&entry_count) > MAX_WORK) { func; else queue_work_node(node, system_unbound_wq, &entry->work) device_unlock(dev) As above show, when it is allowed to do async probes, because of out of memory or work limit, async work is not be allowed, to do sync execute instead. it will lead to A-A deadlock because of __driver_attach_async_helper getting lock dev. Reproduce: and it can be reproduce by make the condition (if (!entry || atomic_read(&entry_count) > MAX_WORK)) untenable, like below: [ 370.785650] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 370.787154] task:swapper/0 state:D stack: 0 pid: 1 ppid: 0 flags:0x00004000 [ 370.788865] Call Trace: [ 370.789374] <TASK> [ 370.789841] __schedule+0x482/0x1050 [ 370.790613] schedule+0x92/0x1a0 [ 370.791290] schedule_preempt_disabled+0x2c/0x50 [ 370.792256] __mutex_lock.isra.0+0x757/0xec0 [ 370.793158] __mutex_lock_slowpath+0x1f/0x30 [ 370.794079] mutex_lock+0x50/0x60 [ 370.794795] __device_driver_lock+0x2f/0x70 [ 370.795677] ? driver_probe_device+0xd0/0xd0 [ 370.796576] __driver_attach_async_helper+0x1d/0xd0 [ 370.797318] ? driver_probe_device+0xd0/0xd0 [ 370.797957] async_schedule_node_domain+0xa5/0xc0 [ 370.798652] async_schedule_node+0x19/0x30 [ 370.799243] __driver_attach+0x246/0x290 [ 370.799828] ? driver_allows_async_probing+0xa0/0xa0 [ 370.800548] bus_for_each_dev+0x9d/0x130 [ 370.801132] driver_attach+0x22/0x30 [ 370.801666] bus_add_driver+0x290/0x340 [ 370.802246] driver_register+0x88/0x140 [ 370.802817] ? virtio_scsi_init+0x116/0x116 [ 370.803425] scsi_register_driver+0x1a/0x30 [ 370.804057] init_sd+0x184/0x226 [ 370.804533] do_one_initcall+0x71/0x3a0 [ 370.805107] kernel_init_freeable+0x39a/0x43a [ 370.805759] ? rest_init+0x150/0x150 [ 370.806283] kernel_init+0x26/0x230 [ 370.806799] ret_from_fork+0x1f/0x30 To fix the deadlock, move the async_schedule_dev outside device_lock, as we can see, in async_schedule_node_domain, the parameter of queue_work_node is system_unbound_wq, so it can accept concurrent operations. which will also not change the code logic, and will not lead to deadlock.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to avoid potential deadlock Using f2fs_trylock_op() in f2fs_write_compressed_pages() to avoid potential deadlock like we did in f2fs_write_single_data_page().

In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: Use request_module_nowait This appears to work around a deadlock regression that came in with the LED merge in 6.9. The deadlock happens on my system with 24 iwlwifi radios, so maybe it something like all worker threads are busy and some work that needs to complete cannot complete. [also remove unnecessary "load_module" var and now-wrong comment]

In the Linux kernel, the following vulnerability has been resolved: Reapply "drm/qxl: simplify qxl_fence_wait" This reverts commit 07ed11afb68d94eadd4ffc082b97c2331307c5ea. Stephen Rostedt reports: "I went to run my tests on my VMs and the tests hung on boot up. Unfortunately, the most I ever got out was: [ 93.607888] Testing event system initcall: OK [ 93.667730] Running tests on all trace events: [ 93.669757] Testing all events: OK [ 95.631064] ------------[ cut here ]------------ Timed out after 60 seconds" and further debugging points to a possible circular locking dependency between the console_owner locking and the worker pool locking. Reverting the commit allows Steve's VM to boot to completion again. [ This may obviously result in the "[TTM] Buffer eviction failed" messages again, which was the reason for that original revert. But at this point this seems preferable to a non-booting system... ]

In the Linux kernel, the following vulnerability has been resolved: stackdepot: fix stack_depot_save_flags() in NMI context Per documentation, stack_depot_save_flags() was meant to be usable from NMI context if STACK_DEPOT_FLAG_CAN_ALLOC is unset. However, it still would try to take the pool_lock in an attempt to save a stack trace in the current pool (if space is available). This could result in deadlock if an NMI is handled while pool_lock is already held. To avoid deadlock, only try to take the lock in NMI context and give up if unsuccessful. The documentation is fixed to clearly convey this.

In the Linux kernel, the following vulnerability has been resolved: drm/ast: Fix soft lockup There is a while-loop in ast_dp_set_on_off() that could lead to infinite-loop. This is because the register, VGACRI-Dx, checked in this API is a scratch register actually controlled by a MCU, named DPMCU, in BMC. These scratch registers are protected by scu-lock. If suc-lock is not off, DPMCU can not update these registers and then host will have soft lockup due to never updated status. DPMCU is used to control DP and relative registers to handshake with host's VGA driver. Even the most time-consuming task, DP's link training, is less than 100ms. 200ms should be enough.

In the Linux kernel, the following vulnerability has been resolved: thermal/debugfs: Fix two locking issues with thermal zone debug With the current thermal zone locking arrangement in the debugfs code, user space can open the "mitigations" file for a thermal zone before the zone's debugfs pointer is set which will result in a NULL pointer dereference in tze_seq_start(). Moreover, thermal_debug_tz_remove() is not called under the thermal zone lock, so it can run in parallel with the other functions accessing the thermal zone's struct thermal_debugfs object. Then, it may clear tz->debugfs after one of those functions has checked it and the struct thermal_debugfs object may be freed prematurely. To address the first problem, pass a pointer to the thermal zone's struct thermal_debugfs object to debugfs_create_file() in thermal_debug_tz_add() and make tze_seq_start(), tze_seq_next(), tze_seq_stop(), and tze_seq_show() retrieve it from s->private instead of a pointer to the thermal zone object. This will ensure that tz_debugfs will be valid across the "mitigations" file accesses until thermal_debugfs_remove_id() called by thermal_debug_tz_remove() removes that file. To address the second problem, use tz->lock in thermal_debug_tz_remove() around the tz->debugfs value check (in case the same thermal zone is removed at the same time in two different threads) and its reset to NULL. Cc :6.8+ <stable@vger.kernel.org> # 6.8+

In the Linux kernel, the following vulnerability has been resolved: net: hinic: avoid kernel hung in hinic_get_stats64() When using hinic device as a bond slave device, and reading device stats of master bond device, the kernel may hung. The kernel panic calltrace as follows: Kernel panic - not syncing: softlockup: hung tasks Call trace: native_queued_spin_lock_slowpath+0x1ec/0x31c dev_get_stats+0x60/0xcc dev_seq_printf_stats+0x40/0x120 dev_seq_show+0x1c/0x40 seq_read_iter+0x3c8/0x4dc seq_read+0xe0/0x130 proc_reg_read+0xa8/0xe0 vfs_read+0xb0/0x1d4 ksys_read+0x70/0xfc __arm64_sys_read+0x20/0x30 el0_svc_common+0x88/0x234 do_el0_svc+0x2c/0x90 el0_svc+0x1c/0x30 el0_sync_handler+0xa8/0xb0 el0_sync+0x148/0x180 And the calltrace of task that actually caused kernel hungs as follows: __switch_to+124 __schedule+548 schedule+72 schedule_timeout+348 __down_common+188 __down+24 down+104 hinic_get_stats64+44 [hinic] dev_get_stats+92 bond_get_stats+172 [bonding] dev_get_stats+92 dev_seq_printf_stats+60 dev_seq_show+24 seq_read_iter+964 seq_read+220 proc_reg_read+164 vfs_read+172 ksys_read+108 __arm64_sys_read+28 el0_svc_common+132 do_el0_svc+40 el0_svc+24 el0_sync_handler+164 el0_sync+324 When getting device stats from bond, kernel will call bond_get_stats(). It first holds the spinlock bond->stats_lock, and then call hinic_get_stats64() to collect hinic device's stats. However, hinic_get_stats64() calls `down(&nic_dev->mgmt_lock)` to protect its critical section, which may schedule current task out. And if system is under high pressure, the task cannot be woken up immediately, which eventually triggers kernel hung panic. Since previous patch has replaced hinic_dev.tx_stats/rx_stats with local variable in hinic_get_stats64(), there is nothing need to be protected by lock, so just removing down()/up() is ok.

In the Linux kernel, the following vulnerability has been resolved: pinctrl: mcp23s08: Fix sleeping in atomic context due to regmap locking If a device uses MCP23xxx IO expander to receive IRQs, the following bug can happen: BUG: sleeping function called from invalid context at kernel/locking/mutex.c:283 in_atomic(): 1, irqs_disabled(): 1, non_block: 0, ... preempt_count: 1, expected: 0 ... Call Trace: ... __might_resched+0x104/0x10e __might_sleep+0x3e/0x62 mutex_lock+0x20/0x4c regmap_lock_mutex+0x10/0x18 regmap_update_bits_base+0x2c/0x66 mcp23s08_irq_set_type+0x1ae/0x1d6 __irq_set_trigger+0x56/0x172 __setup_irq+0x1e6/0x646 request_threaded_irq+0xb6/0x160 ... We observed the problem while experimenting with a touchscreen driver which used MCP23017 IO expander (I2C). The regmap in the pinctrl-mcp23s08 driver uses a mutex for protection from concurrent accesses, which is the default for regmaps without .fast_io, .disable_locking, etc. mcp23s08_irq_set_type() calls regmap_update_bits_base(), and the latter locks the mutex. However, __setup_irq() locks desc->lock spinlock before calling these functions. As a result, the system tries to lock the mutex whole holding the spinlock. It seems, the internal regmap locks are not needed in this driver at all. mcp->lock seems to protect the regmap from concurrent accesses already, except, probably, in mcp_pinconf_get/set. mcp23s08_irq_set_type() and mcp23s08_irq_mask/unmask() are called under chip_bus_lock(), which calls mcp23s08_irq_bus_lock(). The latter takes mcp->lock and enables regmap caching, so that the potentially slow I2C accesses are deferred until chip_bus_unlock(). The accesses to the regmap from mcp23s08_probe_one() do not need additional locking. In all remaining places where the regmap is accessed, except mcp_pinconf_get/set(), the driver already takes mcp->lock. This patch adds locking in mcp_pinconf_get/set() and disables internal locking in the regmap config. Among other things, it fixes the sleeping in atomic context described above.

In the Linux kernel, the following vulnerability has been resolved: bpf: bpf_local_storage: Always use bpf_mem_alloc in PREEMPT_RT In PREEMPT_RT, kmalloc(GFP_ATOMIC) is still not safe in non preemptible context. bpf_mem_alloc must be used in PREEMPT_RT. This patch is to enforce bpf_mem_alloc in the bpf_local_storage when CONFIG_PREEMPT_RT is enabled. [ 35.118559] BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48 [ 35.118566] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 1832, name: test_progs [ 35.118569] preempt_count: 1, expected: 0 [ 35.118571] RCU nest depth: 1, expected: 1 [ 35.118577] INFO: lockdep is turned off. ... [ 35.118647] __might_resched+0x433/0x5b0 [ 35.118677] rt_spin_lock+0xc3/0x290 [ 35.118700] ___slab_alloc+0x72/0xc40 [ 35.118723] __kmalloc_noprof+0x13f/0x4e0 [ 35.118732] bpf_map_kzalloc+0xe5/0x220 [ 35.118740] bpf_selem_alloc+0x1d2/0x7b0 [ 35.118755] bpf_local_storage_update+0x2fa/0x8b0 [ 35.118784] bpf_sk_storage_get_tracing+0x15a/0x1d0 [ 35.118791] bpf_prog_9a118d86fca78ebb_trace_inet_sock_set_state+0x44/0x66 [ 35.118795] bpf_trace_run3+0x222/0x400 [ 35.118820] __bpf_trace_inet_sock_set_state+0x11/0x20 [ 35.118824] trace_inet_sock_set_state+0x112/0x130 [ 35.118830] inet_sk_state_store+0x41/0x90 [ 35.118836] tcp_set_state+0x3b3/0x640 There is no need to adjust the gfp_flags passing to the bpf_mem_cache_alloc_flags() which only honors the GFP_KERNEL. The verifier has ensured GFP_KERNEL is passed only in sleepable context. It has been an old issue since the first introduction of the bpf_local_storage ~5 years ago, so this patch targets the bpf-next. bpf_mem_alloc is needed to solve it, so the Fixes tag is set to the commit when bpf_mem_alloc was first used in the bpf_local_storage.

In the Linux kernel, the following vulnerability has been resolved: ptr_ring: do not block hard interrupts in ptr_ring_resize_multiple() Jakub added a lockdep_assert_no_hardirq() check in __page_pool_put_page() to increase test coverage. syzbot found a splat caused by hard irq blocking in ptr_ring_resize_multiple() [1] As current users of ptr_ring_resize_multiple() do not require hard irqs being masked, replace it to only block BH. Rename helpers to better reflect they are safe against BH only. - ptr_ring_resize_multiple() to ptr_ring_resize_multiple_bh() - skb_array_resize_multiple() to skb_array_resize_multiple_bh() [1] WARNING: CPU: 1 PID: 9150 at net/core/page_pool.c:709 __page_pool_put_page net/core/page_pool.c:709 [inline] WARNING: CPU: 1 PID: 9150 at net/core/page_pool.c:709 page_pool_put_unrefed_netmem+0x157/0xa40 net/core/page_pool.c:780 Modules linked in: CPU: 1 UID: 0 PID: 9150 Comm: syz.1.1052 Not tainted 6.11.0-rc3-syzkaller-00202-gf8669d7b5f5d #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/06/2024 RIP: 0010:__page_pool_put_page net/core/page_pool.c:709 [inline] RIP: 0010:page_pool_put_unrefed_netmem+0x157/0xa40 net/core/page_pool.c:780 Code: 74 0e e8 7c aa fb f7 eb 43 e8 75 aa fb f7 eb 3c 65 8b 1d 38 a8 6a 76 31 ff 89 de e8 a3 ae fb f7 85 db 74 0b e8 5a aa fb f7 90 <0f> 0b 90 eb 1d 65 8b 1d 15 a8 6a 76 31 ff 89 de e8 84 ae fb f7 85 RSP: 0018:ffffc9000bda6b58 EFLAGS: 00010083 RAX: ffffffff8997e523 RBX: 0000000000000000 RCX: 0000000000040000 RDX: ffffc9000fbd0000 RSI: 0000000000001842 RDI: 0000000000001843 RBP: 0000000000000000 R08: ffffffff8997df2c R09: 1ffffd40003a000d R10: dffffc0000000000 R11: fffff940003a000e R12: ffffea0001d00040 R13: ffff88802e8a4000 R14: dffffc0000000000 R15: 00000000ffffffff FS: 00007fb7aaf716c0(0000) GS:ffff8880b9300000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fa15a0d4b72 CR3: 00000000561b0000 CR4: 00000000003506f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> tun_ptr_free drivers/net/tun.c:617 [inline] __ptr_ring_swap_queue include/linux/ptr_ring.h:571 [inline] ptr_ring_resize_multiple_noprof include/linux/ptr_ring.h:643 [inline] tun_queue_resize drivers/net/tun.c:3694 [inline] tun_device_event+0xaaf/0x1080 drivers/net/tun.c:3714 notifier_call_chain+0x19f/0x3e0 kernel/notifier.c:93 call_netdevice_notifiers_extack net/core/dev.c:2032 [inline] call_netdevice_notifiers net/core/dev.c:2046 [inline] dev_change_tx_queue_len+0x158/0x2a0 net/core/dev.c:9024 do_setlink+0xff6/0x41f0 net/core/rtnetlink.c:2923 rtnl_setlink+0x40d/0x5a0 net/core/rtnetlink.c:3201 rtnetlink_rcv_msg+0x73f/0xcf0 net/core/rtnetlink.c:6647 netlink_rcv_skb+0x1e3/0x430 net/netlink/af_netlink.c:2550

In the Linux kernel, the following vulnerability has been resolved: media: uvcvideo: Fix deadlock during uvc_probe If uvc_probe() fails, it can end up calling uvc_status_unregister() before uvc_status_init() is called. Fix this by checking if dev->status is NULL or not in uvc_status_unregister().

In the Linux kernel, the following vulnerability has been resolved: memcg: fix soft lockup in the OOM process A soft lockup issue was found in the product with about 56,000 tasks were in the OOM cgroup, it was traversing them when the soft lockup was triggered. watchdog: BUG: soft lockup - CPU#2 stuck for 23s! [VM Thread:1503066] CPU: 2 PID: 1503066 Comm: VM Thread Kdump: loaded Tainted: G Hardware name: Huawei Cloud OpenStack Nova, BIOS RIP: 0010:console_unlock+0x343/0x540 RSP: 0000:ffffb751447db9a0 EFLAGS: 00000247 ORIG_RAX: ffffffffffffff13 RAX: 0000000000000001 RBX: 0000000000000000 RCX: 00000000ffffffff RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000247 RBP: ffffffffafc71f90 R08: 0000000000000000 R09: 0000000000000040 R10: 0000000000000080 R11: 0000000000000000 R12: ffffffffafc74bd0 R13: ffffffffaf60a220 R14: 0000000000000247 R15: 0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f2fe6ad91f0 CR3: 00000004b2076003 CR4: 0000000000360ee0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: vprintk_emit+0x193/0x280 printk+0x52/0x6e dump_task+0x114/0x130 mem_cgroup_scan_tasks+0x76/0x100 dump_header+0x1fe/0x210 oom_kill_process+0xd1/0x100 out_of_memory+0x125/0x570 mem_cgroup_out_of_memory+0xb5/0xd0 try_charge+0x720/0x770 mem_cgroup_try_charge+0x86/0x180 mem_cgroup_try_charge_delay+0x1c/0x40 do_anonymous_page+0xb5/0x390 handle_mm_fault+0xc4/0x1f0 This is because thousands of processes are in the OOM cgroup, it takes a long time to traverse all of them. As a result, this lead to soft lockup in the OOM process. To fix this issue, call 'cond_resched' in the 'mem_cgroup_scan_tasks' function per 1000 iterations. For global OOM, call 'touch_softlockup_watchdog' per 1000 iterations to avoid this issue.

In the Linux kernel, the following vulnerability has been resolved: virtio-blk: don't keep queue frozen during system suspend Commit 4ce6e2db00de ("virtio-blk: Ensure no requests in virtqueues before deleting vqs.") replaces queue quiesce with queue freeze in virtio-blk's PM callbacks. And the motivation is to drain inflight IOs before suspending. block layer's queue freeze looks very handy, but it is also easy to cause deadlock, such as, any attempt to call into bio_queue_enter() may run into deadlock if the queue is frozen in current context. There are all kinds of ->suspend() called in suspend context, so keeping queue frozen in the whole suspend context isn't one good idea. And Marek reported lockdep warning[1] caused by virtio-blk's freeze queue in virtblk_freeze(). [1] https://lore.kernel.org/linux-block/ca16370e-d646-4eee-b9cc-87277c89c43c@samsung.com/ Given the motivation is to drain in-flight IOs, it can be done by calling freeze & unfreeze, meantime restore to previous behavior by keeping queue quiesced during suspend.

In the Linux kernel, the following vulnerability has been resolved: net: restrict SO_REUSEPORT to inet sockets After blamed commit, crypto sockets could accidentally be destroyed from RCU call back, as spotted by zyzbot [1]. Trying to acquire a mutex in RCU callback is not allowed. Restrict SO_REUSEPORT socket option to inet sockets. v1 of this patch supported TCP, UDP and SCTP sockets, but fcnal-test.sh test needed RAW and ICMP support. [1] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:562 in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 24, name: ksoftirqd/1 preempt_count: 100, expected: 0 RCU nest depth: 0, expected: 0 1 lock held by ksoftirqd/1/24: #0: ffffffff8e937ba0 (rcu_callback){....}-{0:0}, at: rcu_lock_acquire include/linux/rcupdate.h:337 [inline] #0: ffffffff8e937ba0 (rcu_callback){....}-{0:0}, at: rcu_do_batch kernel/rcu/tree.c:2561 [inline] #0: ffffffff8e937ba0 (rcu_callback){....}-{0:0}, at: rcu_core+0xa37/0x17a0 kernel/rcu/tree.c:2823 Preemption disabled at: [<ffffffff8161c8c8>] softirq_handle_begin kernel/softirq.c:402 [inline] [<ffffffff8161c8c8>] handle_softirqs+0x128/0x9b0 kernel/softirq.c:537 CPU: 1 UID: 0 PID: 24 Comm: ksoftirqd/1 Not tainted 6.13.0-rc3-syzkaller-00174-ga024e377efed #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120 __might_resched+0x5d4/0x780 kernel/sched/core.c:8758 __mutex_lock_common kernel/locking/mutex.c:562 [inline] __mutex_lock+0x131/0xee0 kernel/locking/mutex.c:735 crypto_put_default_null_skcipher+0x18/0x70 crypto/crypto_null.c:179 aead_release+0x3d/0x50 crypto/algif_aead.c:489 alg_do_release crypto/af_alg.c:118 [inline] alg_sock_destruct+0x86/0xc0 crypto/af_alg.c:502 __sk_destruct+0x58/0x5f0 net/core/sock.c:2260 rcu_do_batch kernel/rcu/tree.c:2567 [inline] rcu_core+0xaaa/0x17a0 kernel/rcu/tree.c:2823 handle_softirqs+0x2d4/0x9b0 kernel/softirq.c:561 run_ksoftirqd+0xca/0x130 kernel/softirq.c:950 smpboot_thread_fn+0x544/0xa30 kernel/smpboot.c:164 kthread+0x2f0/0x390 kernel/kthread.c:389 ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 </TASK>

In the Linux kernel, the following vulnerability has been resolved: scsi: megaraid_sas: Fix for a potential deadlock This fixes a 'possible circular locking dependency detected' warning CPU0 CPU1 ---- ---- lock(&instance->reset_mutex); lock(&shost->scan_mutex); lock(&instance->reset_mutex); lock(&shost->scan_mutex); Fix this by temporarily releasing the reset_mutex.

In the Linux kernel, the following vulnerability has been resolved: irqchip/gic-v3-its: Don't enable interrupts in its_irq_set_vcpu_affinity() The following call-chain leads to enabling interrupts in a nested interrupt disabled section: irq_set_vcpu_affinity() irq_get_desc_lock() raw_spin_lock_irqsave() <--- Disable interrupts its_irq_set_vcpu_affinity() guard(raw_spinlock_irq) <--- Enables interrupts when leaving the guard() irq_put_desc_unlock() <--- Warns because interrupts are enabled This was broken in commit b97e8a2f7130, which replaced the original raw_spin_[un]lock() pair with guard(raw_spinlock_irq). Fix the issue by using guard(raw_spinlock). [ tglx: Massaged change log ]

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix deadlock when freeing cgroup storage The following commit bc235cdb423a ("bpf: Prevent deadlock from recursive bpf_task_storage_[get|delete]") first introduced deadlock prevention for fentry/fexit programs attaching on bpf_task_storage helpers. That commit also employed the logic in map free path in its v6 version. Later bpf_cgrp_storage was first introduced in c4bcfb38a95e ("bpf: Implement cgroup storage available to non-cgroup-attached bpf progs") which faces the same issue as bpf_task_storage, instead of its busy counter, NULL was passed to bpf_local_storage_map_free() which opened a window to cause deadlock: <TASK> (acquiring local_storage->lock) _raw_spin_lock_irqsave+0x3d/0x50 bpf_local_storage_update+0xd1/0x460 bpf_cgrp_storage_get+0x109/0x130 bpf_prog_a4d4a370ba857314_cgrp_ptr+0x139/0x170 ? __bpf_prog_enter_recur+0x16/0x80 bpf_trampoline_6442485186+0x43/0xa4 cgroup_storage_ptr+0x9/0x20 (holding local_storage->lock) bpf_selem_unlink_storage_nolock.constprop.0+0x135/0x160 bpf_selem_unlink_storage+0x6f/0x110 bpf_local_storage_map_free+0xa2/0x110 bpf_map_free_deferred+0x5b/0x90 process_one_work+0x17c/0x390 worker_thread+0x251/0x360 kthread+0xd2/0x100 ret_from_fork+0x34/0x50 ret_from_fork_asm+0x1a/0x30 </TASK> Progs: - A: SEC("fentry/cgroup_storage_ptr") - cgid (BPF_MAP_TYPE_HASH) Record the id of the cgroup the current task belonging to in this hash map, using the address of the cgroup as the map key. - cgrpa (BPF_MAP_TYPE_CGRP_STORAGE) If current task is a kworker, lookup the above hash map using function parameter @owner as the key to get its corresponding cgroup id which is then used to get a trusted pointer to the cgroup through bpf_cgroup_from_id(). This trusted pointer can then be passed to bpf_cgrp_storage_get() to finally trigger the deadlock issue. - B: SEC("tp_btf/sys_enter") - cgrpb (BPF_MAP_TYPE_CGRP_STORAGE) The only purpose of this prog is to fill Prog A's hash map by calling bpf_cgrp_storage_get() for as many userspace tasks as possible. Steps to reproduce: - Run A; - while (true) { Run B; Destroy B; } Fix this issue by passing its busy counter to the free procedure so it can be properly incremented before storage/smap locking.

In the Linux kernel, the following vulnerability has been resolved: net: ks8851: Handle softirqs at the end of IRQ thread to fix hang The ks8851_irq() thread may call ks8851_rx_pkts() in case there are any packets in the MAC FIFO, which calls netif_rx(). This netif_rx() implementation is guarded by local_bh_disable() and local_bh_enable(). The local_bh_enable() may call do_softirq() to run softirqs in case any are pending. One of the softirqs is net_rx_action, which ultimately reaches the driver .start_xmit callback. If that happens, the system hangs. The entire call chain is below: ks8851_start_xmit_par from netdev_start_xmit netdev_start_xmit from dev_hard_start_xmit dev_hard_start_xmit from sch_direct_xmit sch_direct_xmit from __dev_queue_xmit __dev_queue_xmit from __neigh_update __neigh_update from neigh_update neigh_update from arp_process.constprop.0 arp_process.constprop.0 from __netif_receive_skb_one_core __netif_receive_skb_one_core from process_backlog process_backlog from __napi_poll.constprop.0 __napi_poll.constprop.0 from net_rx_action net_rx_action from __do_softirq __do_softirq from call_with_stack call_with_stack from do_softirq do_softirq from __local_bh_enable_ip __local_bh_enable_ip from netif_rx netif_rx from ks8851_irq ks8851_irq from irq_thread_fn irq_thread_fn from irq_thread irq_thread from kthread kthread from ret_from_fork The hang happens because ks8851_irq() first locks a spinlock in ks8851_par.c ks8851_lock_par() spin_lock_irqsave(&ksp->lock, ...) and with that spinlock locked, calls netif_rx(). Once the execution reaches ks8851_start_xmit_par(), it calls ks8851_lock_par() again which attempts to claim the already locked spinlock again, and the hang happens. Move the do_softirq() call outside of the spinlock protected section of ks8851_irq() by disabling BHs around the entire spinlock protected section of ks8851_irq() handler. Place local_bh_enable() outside of the spinlock protected section, so that it can trigger do_softirq() without the ks8851_par.c ks8851_lock_par() spinlock being held, and safely call ks8851_start_xmit_par() without attempting to lock the already locked spinlock. Since ks8851_irq() is protected by local_bh_disable()/local_bh_enable() now, replace netif_rx() with __netif_rx() which is not duplicating the local_bh_disable()/local_bh_enable() calls.

In the Linux kernel, the following vulnerability has been resolved: ALSA: us122l: Use snd_card_free_when_closed() at disconnection The USB disconnect callback is supposed to be short and not too-long waiting. OTOH, the current code uses snd_card_free() at disconnection, but this waits for the close of all used fds, hence it can take long. It eventually blocks the upper layer USB ioctls, which may trigger a soft lockup. An easy workaround is to replace snd_card_free() with snd_card_free_when_closed(). This variant returns immediately while the release of resources is done asynchronously by the card device release at the last close. The loop of us122l->mmap_count check is dropped as well. The check is useless for the asynchronous operation with *_when_closed().

In the Linux kernel, the following vulnerability has been resolved: nfs_common: must not hold RCU while calling nfsd_file_put_local Move holding the RCU from nfs_to_nfsd_file_put_local to nfs_to_nfsd_net_put. It is the call to nfs_to->nfsd_serv_put that requires the RCU anyway (the puts for nfsd_file and netns were combined to avoid an extra indirect reference but that micro-optimization isn't possible now). This fixes xfstests generic/013 and it triggering: "Voluntary context switch within RCU read-side critical section!" [ 143.545738] Call Trace: [ 143.546206] <TASK> [ 143.546625] ? show_regs+0x6d/0x80 [ 143.547267] ? __warn+0x91/0x140 [ 143.547951] ? rcu_note_context_switch+0x496/0x5d0 [ 143.548856] ? report_bug+0x193/0x1a0 [ 143.549557] ? handle_bug+0x63/0xa0 [ 143.550214] ? exc_invalid_op+0x1d/0x80 [ 143.550938] ? asm_exc_invalid_op+0x1f/0x30 [ 143.551736] ? rcu_note_context_switch+0x496/0x5d0 [ 143.552634] ? wakeup_preempt+0x62/0x70 [ 143.553358] __schedule+0xaa/0x1380 [ 143.554025] ? _raw_spin_unlock_irqrestore+0x12/0x40 [ 143.554958] ? try_to_wake_up+0x1fe/0x6b0 [ 143.555715] ? wake_up_process+0x19/0x20 [ 143.556452] schedule+0x2e/0x120 [ 143.557066] schedule_preempt_disabled+0x19/0x30 [ 143.557933] rwsem_down_read_slowpath+0x24d/0x4a0 [ 143.558818] ? xfs_efi_item_format+0x50/0xc0 [xfs] [ 143.559894] down_read+0x4e/0xb0 [ 143.560519] xlog_cil_commit+0x1b2/0xbc0 [xfs] [ 143.561460] ? _raw_spin_unlock+0x12/0x30 [ 143.562212] ? xfs_inode_item_precommit+0xc7/0x220 [xfs] [ 143.563309] ? xfs_trans_run_precommits+0x69/0xd0 [xfs] [ 143.564394] __xfs_trans_commit+0xb5/0x330 [xfs] [ 143.565367] xfs_trans_roll+0x48/0xc0 [xfs] [ 143.566262] xfs_defer_trans_roll+0x57/0x100 [xfs] [ 143.567278] xfs_defer_finish_noroll+0x27a/0x490 [xfs] [ 143.568342] xfs_defer_finish+0x1a/0x80 [xfs] [ 143.569267] xfs_bunmapi_range+0x4d/0xb0 [xfs] [ 143.570208] xfs_itruncate_extents_flags+0x13d/0x230 [xfs] [ 143.571353] xfs_free_eofblocks+0x12e/0x190 [xfs] [ 143.572359] xfs_file_release+0x12d/0x140 [xfs] [ 143.573324] __fput+0xe8/0x2d0 [ 143.573922] __fput_sync+0x1d/0x30 [ 143.574574] nfsd_filp_close+0x33/0x60 [nfsd] [ 143.575430] nfsd_file_free+0x96/0x150 [nfsd] [ 143.576274] nfsd_file_put+0xf7/0x1a0 [nfsd] [ 143.577104] nfsd_file_put_local+0x18/0x30 [nfsd] [ 143.578070] nfs_close_local_fh+0x101/0x110 [nfs_localio] [ 143.579079] __put_nfs_open_context+0xc9/0x180 [nfs] [ 143.580031] nfs_file_clear_open_context+0x4a/0x60 [nfs] [ 143.581038] nfs_file_release+0x3e/0x60 [nfs] [ 143.581879] __fput+0xe8/0x2d0 [ 143.582464] __fput_sync+0x1d/0x30 [ 143.583108] __x64_sys_close+0x41/0x80 [ 143.583823] x64_sys_call+0x189a/0x20d0 [ 143.584552] do_syscall_64+0x64/0x170 [ 143.585240] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 143.586185] RIP: 0033:0x7f3c5153efd7

In the Linux kernel, the following vulnerability has been resolved: usb: musb: Fix hardware lockup on first Rx endpoint request There is a possibility that a request's callback could be invoked from usb_ep_queue() (call trace below, supplemented with missing calls): req->complete from usb_gadget_giveback_request (drivers/usb/gadget/udc/core.c:999) usb_gadget_giveback_request from musb_g_giveback (drivers/usb/musb/musb_gadget.c:147) musb_g_giveback from rxstate (drivers/usb/musb/musb_gadget.c:784) rxstate from musb_ep_restart (drivers/usb/musb/musb_gadget.c:1169) musb_ep_restart from musb_ep_restart_resume_work (drivers/usb/musb/musb_gadget.c:1176) musb_ep_restart_resume_work from musb_queue_resume_work (drivers/usb/musb/musb_core.c:2279) musb_queue_resume_work from musb_gadget_queue (drivers/usb/musb/musb_gadget.c:1241) musb_gadget_queue from usb_ep_queue (drivers/usb/gadget/udc/core.c:300) According to the docstring of usb_ep_queue(), this should not happen: "Note that @req's ->complete() callback must never be called from within usb_ep_queue() as that can create deadlock situations." In fact, a hardware lockup might occur in the following sequence: 1. The gadget is initialized using musb_gadget_enable(). 2. Meanwhile, a packet arrives, and the RXPKTRDY flag is set, raising an interrupt. 3. If IRQs are enabled, the interrupt is handled, but musb_g_rx() finds an empty queue (next_request() returns NULL). The interrupt flag has already been cleared by the glue layer handler, but the RXPKTRDY flag remains set. 4. The first request is enqueued using usb_ep_queue(), leading to the call of req->complete(), as shown in the call trace above. 5. If the callback enables IRQs and another packet is waiting, step (3) repeats. The request queue is empty because usb_g_giveback() removes the request before invoking the callback. 6. The endpoint remains locked up, as the interrupt triggered by hardware setting the RXPKTRDY flag has been handled, but the flag itself remains set. For this scenario to occur, it is only necessary for IRQs to be enabled at some point during the complete callback. This happens with the USB Ethernet gadget, whose rx_complete() callback calls netif_rx(). If called in the task context, netif_rx() disables the bottom halves (BHs). When the BHs are re-enabled, IRQs are also enabled to allow soft IRQs to be processed. The gadget itself is initialized at module load (or at boot if built-in), but the first request is enqueued when the network interface is brought up, triggering rx_complete() in the task context via ioctl(). If a packet arrives while the interface is down, it can prevent the interface from receiving any further packets from the USB host. The situation is quite complicated with many parties involved. This particular issue can be resolved in several possible ways: 1. Ensure that callbacks never enable IRQs. This would be difficult to enforce, as discovering how netif_rx() interacts with interrupts was already quite challenging and u_ether is not the only function driver. Similar "bugs" could be hidden in other drivers as well. 2. Disable MUSB interrupts in musb_g_giveback() before calling the callback and re-enable them afterwars (by calling musb_{dis,en}able_interrupts(), for example). This would ensure that MUSB interrupts are not handled during the callback, even if IRQs are enabled. In fact, it would allow IRQs to be enabled when releasing the lock. However, this feels like an inelegant hack. 3. Modify the interrupt handler to clear the RXPKTRDY flag if the request queue is empty. While this approach also feels like a hack, it wastes CPU time by attempting to handle incoming packets when the software is not ready to process them. 4. Flush the Rx FIFO instead of calling rxstate() in musb_ep_restart(). This ensures that the hardware can receive packets when there is at least one request in the queue. Once I ---truncated---

In the Linux kernel, the following vulnerability has been resolved: drm/panthor: Lock XArray when getting entries for the VM Similar to commit cac075706f29 ("drm/panthor: Fix race when converting group handle to group object") we need to use the XArray's internal locking when retrieving a vm pointer from there. v2: Removed part of the patch that was trying to protect fetching the heap pointer from XArray, as that operation is protected by the @pool->lock.

In the Linux kernel, the following vulnerability has been resolved: tpm: Lock TPM chip in tpm_pm_suspend() first Setting TPM_CHIP_FLAG_SUSPENDED in the end of tpm_pm_suspend() can be racy according, as this leaves window for tpm_hwrng_read() to be called while the operation is in progress. The recent bug report gives also evidence of this behaviour. Aadress this by locking the TPM chip before checking any chip->flags both in tpm_pm_suspend() and tpm_hwrng_read(). Move TPM_CHIP_FLAG_SUSPENDED check inside tpm_get_random() so that it will be always checked only when the lock is reserved.

In the Linux kernel, the following vulnerability has been resolved: drm/xe: Drop VM dma-resv lock on xe_sync_in_fence_get failure in exec IOCTL Upon failure all locks need to be dropped before returning to the user. (cherry picked from commit 7d1a4258e602ffdce529f56686925034c1b3b095)

In the Linux kernel, the following vulnerability has been resolved: spi: use generic driver_override infrastructure When a driver is probed through __driver_attach(), the bus' match() callback is called without the device lock held, thus accessing the driver_override field without a lock, which can cause a UAF. Fix this by using the driver-core driver_override infrastructure taking care of proper locking internally. Note that calling match() from __driver_attach() without the device lock held is intentional. [1] Also note that we do not enable the driver_override feature of struct bus_type, as SPI - in contrast to most other buses - passes "" to sysfs_emit() when the driver_override pointer is NULL. Thus, printing "\n" instead of "(null)\n".

In the Linux kernel, the following vulnerability has been resolved: RDMA/irdma: Fix deadlock during netdev reset with active connections Resolve deadlock that occurs when user executes netdev reset while RDMA applications (e.g., rping) are active. The netdev reset causes ice driver to remove irdma auxiliary driver, triggering device_delete and subsequent client removal. During client removal, uverbs_client waits for QP reference count to reach zero while cma_client holds the final reference, creating circular dependency and indefinite wait in iWARP mode. Skip QP reference count wait during device reset to prevent deadlock.

In the Linux kernel, the following vulnerability has been resolved: nfc: nci: fix circular locking dependency in nci_close_device nci_close_device() flushes rx_wq and tx_wq while holding req_lock. This causes a circular locking dependency because nci_rx_work() running on rx_wq can end up taking req_lock too: nci_rx_work -> nci_rx_data_packet -> nci_data_exchange_complete -> __sk_destruct -> rawsock_destruct -> nfc_deactivate_target -> nci_deactivate_target -> nci_request -> mutex_lock(&ndev->req_lock) Move the flush of rx_wq after req_lock has been released. This should safe (I think) because NCI_UP has already been cleared and the transport is closed, so the work will see it and return -ENETDOWN. NIPA has been hitting this running the nci selftest with a debug kernel on roughly 4% of the runs.

In the Linux kernel, the following vulnerability has been resolved: usb: dwc2: gadget: Fix spin_lock/unlock mismatch in dwc2_hsotg_udc_stop() dwc2_gadget_exit_clock_gating() internally calls call_gadget() macro, which expects hsotg->lock to be held since it does spin_unlock/spin_lock around the gadget driver callback invocation. However, dwc2_hsotg_udc_stop() calls dwc2_gadget_exit_clock_gating() without holding the lock. This leads to: - spin_unlock on a lock that is not held (undefined behavior) - The lock remaining held after dwc2_gadget_exit_clock_gating() returns, causing a deadlock when spin_lock_irqsave() is called later in the same function. Fix this by acquiring hsotg->lock before calling dwc2_gadget_exit_clock_gating() and releasing it afterwards, which satisfies the locking requirement of the call_gadget() macro.

In the Linux kernel, the following vulnerability has been resolved: gpio: omap: do not register driver in probe() Commit 11a78b794496 ("ARM: OMAP: MPUIO wake updates") registers the omap_mpuio_driver from omap_mpuio_init(), which is called from omap_gpio_probe(). However, it neither makes sense to register drivers from probe() callbacks of other drivers, nor does the driver core allow registering drivers with a device lock already being held. The latter was revealed by commit dc23806a7c47 ("driver core: enforce device_lock for driver_match_device()") leading to a potential deadlock condition described in [1]. Additionally, the omap_mpuio_driver is never unregistered from the driver core, even if the module is unloaded. Hence, register the omap_mpuio_driver from the module initcall and unregister it in module_exit().

In the Linux kernel, the following vulnerability has been resolved: rhashtable: Fix potential deadlock by moving schedule_work outside lock Move the hash table growth check and work scheduling outside the rht lock to prevent a possible circular locking dependency. The original implementation could trigger a lockdep warning due to a potential deadlock scenario involving nested locks between rhashtable bucket, rq lock, and dsq lock. By relocating the growth check and work scheduling after releasing the rth lock, we break this potential deadlock chain. This change expands the flexibility of rhashtable by removing restrictive locking that previously limited its use in scheduler and workqueue contexts. Import to say that this calls rht_grow_above_75(), which reads from struct rhashtable without holding the lock, if this is a problem, we can move the check to the lock, and schedule the workqueue after the lock. Modified so that atomic_inc is also moved outside of the bucket lock along with the growth above 75% check.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to avoid potential deadlock in f2fs_record_stop_reason() syzbot reports deadlock issue of f2fs as below: ====================================================== WARNING: possible circular locking dependency detected 6.12.0-rc3-syzkaller-00087-gc964ced77262 #0 Not tainted ------------------------------------------------------ kswapd0/79 is trying to acquire lock: ffff888011824088 (&sbi->sb_lock){++++}-{3:3}, at: f2fs_down_write fs/f2fs/f2fs.h:2199 [inline] ffff888011824088 (&sbi->sb_lock){++++}-{3:3}, at: f2fs_record_stop_reason+0x52/0x1d0 fs/f2fs/super.c:4068 but task is already holding lock: ffff88804bd92610 (sb_internal#2){.+.+}-{0:0}, at: f2fs_evict_inode+0x662/0x15c0 fs/f2fs/inode.c:842 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (sb_internal#2){.+.+}-{0:0}: lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5825 percpu_down_read include/linux/percpu-rwsem.h:51 [inline] __sb_start_write include/linux/fs.h:1716 [inline] sb_start_intwrite+0x4d/0x1c0 include/linux/fs.h:1899 f2fs_evict_inode+0x662/0x15c0 fs/f2fs/inode.c:842 evict+0x4e8/0x9b0 fs/inode.c:725 f2fs_evict_inode+0x1a4/0x15c0 fs/f2fs/inode.c:807 evict+0x4e8/0x9b0 fs/inode.c:725 dispose_list fs/inode.c:774 [inline] prune_icache_sb+0x239/0x2f0 fs/inode.c:963 super_cache_scan+0x38c/0x4b0 fs/super.c:223 do_shrink_slab+0x701/0x1160 mm/shrinker.c:435 shrink_slab+0x1093/0x14d0 mm/shrinker.c:662 shrink_one+0x43b/0x850 mm/vmscan.c:4818 shrink_many mm/vmscan.c:4879 [inline] lru_gen_shrink_node mm/vmscan.c:4957 [inline] shrink_node+0x3799/0x3de0 mm/vmscan.c:5937 kswapd_shrink_node mm/vmscan.c:6765 [inline] balance_pgdat mm/vmscan.c:6957 [inline] kswapd+0x1ca3/0x3700 mm/vmscan.c:7226 kthread+0x2f0/0x390 kernel/kthread.c:389 ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 -> #1 (fs_reclaim){+.+.}-{0:0}: lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5825 __fs_reclaim_acquire mm/page_alloc.c:3834 [inline] fs_reclaim_acquire+0x88/0x130 mm/page_alloc.c:3848 might_alloc include/linux/sched/mm.h:318 [inline] prepare_alloc_pages+0x147/0x5b0 mm/page_alloc.c:4493 __alloc_pages_noprof+0x16f/0x710 mm/page_alloc.c:4722 alloc_pages_mpol_noprof+0x3e8/0x680 mm/mempolicy.c:2265 alloc_pages_noprof mm/mempolicy.c:2345 [inline] folio_alloc_noprof+0x128/0x180 mm/mempolicy.c:2352 filemap_alloc_folio_noprof+0xdf/0x500 mm/filemap.c:1010 do_read_cache_folio+0x2eb/0x850 mm/filemap.c:3787 read_mapping_folio include/linux/pagemap.h:1011 [inline] f2fs_commit_super+0x3c0/0x7d0 fs/f2fs/super.c:4032 f2fs_record_stop_reason+0x13b/0x1d0 fs/f2fs/super.c:4079 f2fs_handle_critical_error+0x2ac/0x5c0 fs/f2fs/super.c:4174 f2fs_write_inode+0x35f/0x4d0 fs/f2fs/inode.c:785 write_inode fs/fs-writeback.c:1503 [inline] __writeback_single_inode+0x711/0x10d0 fs/fs-writeback.c:1723 writeback_single_inode+0x1f3/0x660 fs/fs-writeback.c:1779 sync_inode_metadata+0xc4/0x120 fs/fs-writeback.c:2849 f2fs_release_file+0xa8/0x100 fs/f2fs/file.c:1941 __fput+0x23f/0x880 fs/file_table.c:431 task_work_run+0x24f/0x310 kernel/task_work.c:228 resume_user_mode_work include/linux/resume_user_mode.h:50 [inline] exit_to_user_mode_loop kernel/entry/common.c:114 [inline] exit_to_user_mode_prepare include/linux/entry-common.h:328 [inline] __syscall_exit_to_user_mode_work kernel/entry/common.c:207 [inline] syscall_exit_to_user_mode+0x168/0x370 kernel/entry/common.c:218 do_syscall_64+0x100/0x230 arch/x86/entry/common.c:89 entry_SYSCALL_64_after_hwframe+0x77/0x7f ---truncated---

In the Linux kernel, the following vulnerability has been resolved: pinmux: Use sequential access to access desc->pinmux data When two client of the same gpio call pinctrl_select_state() for the same functionality, we are seeing NULL pointer issue while accessing desc->mux_owner. Let's say two processes A, B executing in pin_request() for the same pin and process A updates the desc->mux_usecount but not yet updated the desc->mux_owner while process B see the desc->mux_usecount which got updated by A path and further executes strcmp and while accessing desc->mux_owner it crashes with NULL pointer. Serialize the access to mux related setting with a mutex lock. cpu0 (process A) cpu1(process B) pinctrl_select_state() { pinctrl_select_state() { pin_request() { pin_request() { ... .... } else { desc->mux_usecount++; desc->mux_usecount && strcmp(desc->mux_owner, owner)) { if (desc->mux_usecount > 1) return 0; desc->mux_owner = owner; } }