In the Linux kernel, the following vulnerability has been resolved: usb: dwc2: gadget: Fix spin_lock/unlock mismatch in dwc2_hsotg_udc_stop() dwc2_gadget_exit_clock_gating() internally calls call_gadget() macro, which expects hsotg->lock to be held since it does spin_unlock/spin_lock around the gadget driver callback invocation. However, dwc2_hsotg_udc_stop() calls dwc2_gadget_exit_clock_gating() without holding the lock. This leads to: - spin_unlock on a lock that is not held (undefined behavior) - The lock remaining held after dwc2_gadget_exit_clock_gating() returns, causing a deadlock when spin_lock_irqsave() is called later in the same function. Fix this by acquiring hsotg->lock before calling dwc2_gadget_exit_clock_gating() and releasing it afterwards, which satisfies the locking requirement of the call_gadget() macro.

In the Linux kernel, the following vulnerability has been resolved: counter: rz-mtu3-cnt: prevent counter from being toggled multiple times Runtime PM counter is incremented / decremented each time the sysfs enable file is written to. If user writes 0 to the sysfs enable file multiple times, runtime PM usage count underflows, generating the following message. rz-mtu3-counter rz-mtu3-counter.0: Runtime PM usage count underflow! At the same time, hardware registers end up being accessed with clocks off in rz_mtu3_terminate_counter() to disable an already disabled channel. If user writes 1 to the sysfs enable file multiple times, runtime PM usage count will be incremented each time, requiring the same number of 0 writes to get it back to 0. If user writes 0 to the sysfs enable file while PWM is in progress, PWM is stopped without counter being the owner of the underlying MTU3 channel. Check against the cached count_is_enabled value and exit if the user is trying to set the same enable value.

In the Linux kernel, the following vulnerability has been resolved: spi: amlogic: spifc-a4: unregister ECC engine on probe failure and remove() callback aml_sfc_probe() registers the on-host NAND ECC engine, but teardown was missing from both probe unwind and remove-time cleanup. Add a devm cleanup action after successful registration so nand_ecc_unregister_on_host_hw_engine() runs automatically on probe failures and during device removal.

rpmsg_virtio_add_ctrl_dev in drivers/rpmsg/virtio_rpmsg_bus.c in the Linux kernel before 5.18.4 has a double free.

In the Linux kernel, the following vulnerability has been resolved: rxrpc: Fix leak of rxgk context in rxgk_verify_response() Fix rxgk_verify_response() to clean up the rxgk context it creates.

In the Linux kernel, the following vulnerability has been resolved: NFC: nxp-nci: allow GPIOs to sleep Allow the firmware and enable GPIOs to sleep. This fixes a `WARN_ON' and allows the driver to operate GPIOs which are connected to I2C GPIO expanders. -- >8 -- kernel: WARNING: CPU: 3 PID: 2636 at drivers/gpio/gpiolib.c:3880 gpiod_set_value+0x88/0x98 -- >8 --

In the Linux kernel, the following vulnerability has been resolved: fbdev: tdfxfb: avoid divide-by-zero on FBIOPUT_VSCREENINFO Much like commit 19f953e74356 ("fbdev: fb_pm2fb: Avoid potential divide by zero error"), we also need to prevent that same crash from happening in the udlfb driver as it uses pixclock directly when dividing, which will crash.

In the Linux kernel, the following vulnerability has been resolved: firmware: arm_scmi: Fix NULL dereference on notify error path Since commit b5daf93b809d1 ("firmware: arm_scmi: Avoid notifier registration for unsupported events") the call chains leading to the helper __scmi_event_handler_get_ops expect an ERR_PTR to be returned on failure to get an handler for the requested event key, while the current helper can still return a NULL when no handler could be found or created. Fix by forcing an ERR_PTR return value when the handler reference is NULL.

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: f_ecm: Fix net_device lifecycle with device_move The net_device is allocated during function instance creation and registered during the bind phase with the gadget device as its sysfs parent. When the function unbinds, the parent device is destroyed, but the net_device survives, resulting in dangling sysfs symlinks: console:/ # ls -l /sys/class/net/usb0 lrwxrwxrwx ... /sys/class/net/usb0 -> /sys/devices/platform/.../gadget.0/net/usb0 console:/ # ls -l /sys/devices/platform/.../gadget.0/net/usb0 ls: .../gadget.0/net/usb0: No such file or directory Use device_move() to reparent the net_device between the gadget device tree and /sys/devices/virtual across bind and unbind cycles. During the final unbind, calling device_move(NULL) moves the net_device to the virtual device tree before the gadget device is destroyed. On rebinding, device_move() reparents the device back under the new gadget, ensuring proper sysfs topology and power management ordering. To maintain compatibility with legacy composite drivers (e.g., multi.c), the bound flag is used to indicate whether the network device is shared and pre-registered during the legacy driver's bind phase.

In the Linux kernel, the following vulnerability has been resolved: drm/i915/dsi: Don't do DSC horizontal timing adjustments in command mode Stop adjusting the horizontal timing values based on the compression ratio in command mode. Bspec seems to be telling us to do this only in video mode, and this is also how the Windows driver does things. This should also fix a div-by-zero on some machines because the adjusted htotal ends up being so small that we end up with line_time_us==0 when trying to determine the vtotal value in command mode. Note that this doesn't actually make the display on the Huawei Matebook E work, but at least the kernel no longer explodes when the driver loads. (cherry picked from commit 0b475e91ecc2313207196c6d7fd5c53e1a878525)

In the Linux kernel, the following vulnerability has been resolved: ipv4: nexthop: allocate skb dynamically in rtm_get_nexthop() When querying a nexthop object via RTM_GETNEXTHOP, the kernel currently allocates a fixed-size skb using NLMSG_GOODSIZE. While sufficient for single nexthops and small Equal-Cost Multi-Path groups, this fixed allocation fails for large nexthop groups like 512 nexthops. This results in the following warning splat: WARNING: net/ipv4/nexthop.c:3395 at rtm_get_nexthop+0x176/0x1c0, CPU#20: rep/4608 [...] RIP: 0010:rtm_get_nexthop (net/ipv4/nexthop.c:3395) [...] Call Trace: <TASK> rtnetlink_rcv_msg (net/core/rtnetlink.c:6989) netlink_rcv_skb (net/netlink/af_netlink.c:2550) netlink_unicast (net/netlink/af_netlink.c:1319 net/netlink/af_netlink.c:1344) netlink_sendmsg (net/netlink/af_netlink.c:1894) ____sys_sendmsg (net/socket.c:721 net/socket.c:736 net/socket.c:2585) ___sys_sendmsg (net/socket.c:2641) __sys_sendmsg (net/socket.c:2671) do_syscall_64 (arch/x86/entry/syscall_64.c:63 arch/x86/entry/syscall_64.c:94) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130) </TASK> Fix this by allocating the size dynamically using nh_nlmsg_size() and using nlmsg_new(), this is consistent with nexthop_notify() behavior. In addition, adjust nh_nlmsg_size_grp() so it calculates the size needed based on flags passed. While at it, also add the size of NHA_FDB for nexthop group size calculation as it was missing too. This cannot be reproduced via iproute2 as the group size is currently limited and the command fails as follows: addattr_l ERROR: message exceeded bound of 1048

In the Linux kernel, the following vulnerability has been resolved: cxl/region: Fix leakage in __construct_region() Failing the first sysfs_update_group() needs to explicitly kfree the resource as it is too early for cxl_region_iomem_release() to do so.

In the Linux kernel, the following vulnerability has been resolved: pmdomain: imx8mp-blk-ctrl: Keep the NOC_HDCP clock enabled Keep the NOC_HDCP clock always enabled to fix the potential hang caused by the NoC ADB400 port power down handshake.

In the Linux kernel, the following vulnerability has been resolved: usb: misc: usbio: Fix URB memory leak on submit failure When usb_submit_urb() fails in usbio_probe(), the previously allocated URB is never freed, causing a memory leak. Fix this by jumping to err_free_urb label to properly release the URB on the error path.

In the Linux kernel, the following vulnerability has been resolved: sched_ext: Fix is_bpf_migration_disabled() false negative on non-PREEMPT_RCU Since commit 8e4f0b1ebcf2 ("bpf: use rcu_read_lock_dont_migrate() for trampoline.c"), the BPF prolog (__bpf_prog_enter) calls migrate_disable() only when CONFIG_PREEMPT_RCU is enabled, via rcu_read_lock_dont_migrate(). Without CONFIG_PREEMPT_RCU, the prolog never touches migration_disabled, so migration_disabled == 1 always means the task is truly migration-disabled regardless of whether it is the current task. The old unconditional p == current check was a false negative in this case, potentially allowing a migration-disabled task to be dispatched to a remote CPU and triggering scx_error in task_can_run_on_remote_rq(). Only apply the p == current disambiguation when CONFIG_PREEMPT_RCU is enabled, where the ambiguity with the BPF prolog still exists.

A denial of service vulnerability was found in tipc_crypto_key_revoke in net/tipc/crypto.c in the Linux kernel’s TIPC subsystem. This flaw allows guests with local user privileges to trigger a deadlock and potentially crash the system.

In the Linux kernel, the following vulnerability has been resolved: net: ethernet: mtk_ppe: avoid NULL deref when gmac0 is disabled If the gmac0 is disabled, the precheck for a valid ingress device will cause a NULL pointer deref and crash the system. This happens because eth->netdev[0] will be NULL but the code will directly try to access netdev_ops. Instead of just checking for the first net_device, it must be checked if any of the mtk_eth net_devices is matching the netdev_ops of the ingress device.

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: f_rndis: Fix net_device lifecycle with device_move The net_device is allocated during function instance creation and registered during the bind phase with the gadget device as its sysfs parent. When the function unbinds, the parent device is destroyed, but the net_device survives, resulting in dangling sysfs symlinks: console:/ # ls -l /sys/class/net/usb0 lrwxrwxrwx ... /sys/class/net/usb0 -> /sys/devices/platform/.../gadget.0/net/usb0 console:/ # ls -l /sys/devices/platform/.../gadget.0/net/usb0 ls: .../gadget.0/net/usb0: No such file or directory Use device_move() to reparent the net_device between the gadget device tree and /sys/devices/virtual across bind and unbind cycles. During the final unbind, calling device_move(NULL) moves the net_device to the virtual device tree before the gadget device is destroyed. On rebinding, device_move() reparents the device back under the new gadget, ensuring proper sysfs topology and power management ordering. To maintain compatibility with legacy composite drivers (e.g., multi.c), the borrowed_net flag is used to indicate whether the network device is shared and pre-registered during the legacy driver's bind phase.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to avoid memory leak in f2fs_rename() syzbot reported a f2fs bug as below: BUG: memory leak unreferenced object 0xffff888127f70830 (size 16): comm "syz.0.23", pid 6144, jiffies 4294943712 hex dump (first 16 bytes): 3c af 57 72 5b e6 8f ad 6e 8e fd 33 42 39 03 ff <.Wr[...n..3B9.. backtrace (crc 925f8a80): kmemleak_alloc_recursive include/linux/kmemleak.h:44 [inline] slab_post_alloc_hook mm/slub.c:4520 [inline] slab_alloc_node mm/slub.c:4844 [inline] __do_kmalloc_node mm/slub.c:5237 [inline] __kmalloc_noprof+0x3bd/0x560 mm/slub.c:5250 kmalloc_noprof include/linux/slab.h:954 [inline] fscrypt_setup_filename+0x15e/0x3b0 fs/crypto/fname.c:364 f2fs_setup_filename+0x52/0xb0 fs/f2fs/dir.c:143 f2fs_rename+0x159/0xca0 fs/f2fs/namei.c:961 f2fs_rename2+0xd5/0xf20 fs/f2fs/namei.c:1308 vfs_rename+0x7ff/0x1250 fs/namei.c:6026 filename_renameat2+0x4f4/0x660 fs/namei.c:6144 __do_sys_renameat2 fs/namei.c:6173 [inline] __se_sys_renameat2 fs/namei.c:6168 [inline] __x64_sys_renameat2+0x59/0x80 fs/namei.c:6168 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xe2/0xf80 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f The root cause is in commit 40b2d55e0452 ("f2fs: fix to create selinux label during whiteout initialization"), we added a call to f2fs_setup_filename() without a matching call to f2fs_free_filename(), fix it.

In the Linux kernel, the following vulnerability has been resolved: LoongArch: Fix missing NULL checks for kstrdup() 1. Replace "of_find_node_by_path("/")" with "of_root" to avoid multiple calls to "of_node_put()". 2. Fix a potential kernel oops during early boot when memory allocation fails while parsing CPU model from device tree.

In the Linux kernel, the following vulnerability has been resolved: RDMA/irdma: Fix deadlock during netdev reset with active connections Resolve deadlock that occurs when user executes netdev reset while RDMA applications (e.g., rping) are active. The netdev reset causes ice driver to remove irdma auxiliary driver, triggering device_delete and subsequent client removal. During client removal, uverbs_client waits for QP reference count to reach zero while cma_client holds the final reference, creating circular dependency and indefinite wait in iWARP mode. Skip QP reference count wait during device reset to prevent deadlock.

In the Linux kernel, the following vulnerability has been resolved: futex: Clear stale exiting pointer in futex_lock_pi() retry path Fuzzying/stressing futexes triggered: WARNING: kernel/futex/core.c:825 at wait_for_owner_exiting+0x7a/0x80, CPU#11: futex_lock_pi_s/524 When futex_lock_pi_atomic() sees the owner is exiting, it returns -EBUSY and stores a refcounted task pointer in 'exiting'. After wait_for_owner_exiting() consumes that reference, the local pointer is never reset to nil. Upon a retry, if futex_lock_pi_atomic() returns a different error, the bogus pointer is passed to wait_for_owner_exiting(). CPU0 CPU1 CPU2 futex_lock_pi(uaddr) // acquires the PI futex exit() futex_cleanup_begin() futex_state = EXITING; futex_lock_pi(uaddr) futex_lock_pi_atomic() attach_to_pi_owner() // observes EXITING *exiting = owner; // takes ref return -EBUSY wait_for_owner_exiting(-EBUSY, owner) put_task_struct(); // drops ref // exiting still points to owner goto retry; futex_lock_pi_atomic() lock_pi_update_atomic() cmpxchg(uaddr) *uaddr ^= WAITERS // whatever // value changed return -EAGAIN; wait_for_owner_exiting(-EAGAIN, exiting) // stale WARN_ON_ONCE(exiting) Fix this by resetting upon retry, essentially aligning it with requeue_pi.

In the Linux kernel, the following vulnerability has been resolved: ALSA: caiaq: take a reference on the USB device in create_card() The caiaq driver stores a pointer to the parent USB device in cdev->chip.dev but never takes a reference on it. The card's private_free callback, snd_usb_caiaq_card_free(), can run asynchronously via snd_card_free_when_closed() after the USB device has already been disconnected and freed, so any access to cdev->chip.dev in that path dereferences a freed usb_device. On top of the refcounting issue, the current card_free implementation calls usb_reset_device(cdev->chip.dev). A reset in a free callback is inappropriate: the device is going away, the call takes the device lock in a teardown context, and the reset races with the disconnect path that the callback is already cleaning up after. Take a reference on the USB device in create_card() with usb_get_dev(), drop it with usb_put_dev() in the free callback, and remove the usb_reset_device() call.

In the Linux kernel, the following vulnerability has been resolved: sched_ext: Fix stale direct dispatch state in ddsp_dsq_id @p->scx.ddsp_dsq_id can be left set (non-SCX_DSQ_INVALID) triggering a spurious warning in mark_direct_dispatch() when the next wakeup's ops.select_cpu() calls scx_bpf_dsq_insert(), such as: WARNING: kernel/sched/ext.c:1273 at scx_dsq_insert_commit+0xcd/0x140 The root cause is that ddsp_dsq_id was only cleared in dispatch_enqueue(), which is not reached in all paths that consume or cancel a direct dispatch verdict. Fix it by clearing it at the right places: - direct_dispatch(): cache the direct dispatch state in local variables and clear it before dispatch_enqueue() on the synchronous path. For the deferred path, the direct dispatch state must remain set until process_ddsp_deferred_locals() consumes them. - process_ddsp_deferred_locals(): cache the dispatch state in local variables and clear it before calling dispatch_to_local_dsq(), which may migrate the task to another rq. - do_enqueue_task(): clear the dispatch state on the enqueue path (local/global/bypass fallbacks), where the direct dispatch verdict is ignored. - dequeue_task_scx(): clear the dispatch state after dispatch_dequeue() to handle both the deferred dispatch cancellation and the holding_cpu race, covering all cases where a pending direct dispatch is cancelled. - scx_disable_task(): clear the direct dispatch state when transitioning a task out of the current scheduler. Waking tasks may have had the direct dispatch state set by the outgoing scheduler's ops.select_cpu() and then been queued on a wake_list via ttwu_queue_wakelist(), when SCX_OPS_ALLOW_QUEUED_WAKEUP is set. Such tasks are not on the runqueue and are not iterated by scx_bypass(), so their direct dispatch state won't be cleared. Without this clear, any subsequent SCX scheduler that tries to direct dispatch the task will trigger the WARN_ON_ONCE() in mark_direct_dispatch().

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: f_ncm: validate minimum block_len in ncm_unwrap_ntb() The block_len read from the host-supplied NTB header is checked against ntb_max but has no lower bound. When block_len is smaller than opts->ndp_size, the bounds check of: ndp_index > (block_len - opts->ndp_size) will underflow producing a huge unsigned value that ndp_index can never exceed, defeating the check entirely. The same underflow occurs in the datagram index checks against block_len - opts->dpe_size. With those checks neutered, a malicious USB host can choose ndp_index and datagram offsets that point past the actual transfer, and the skb_put_data() copies adjacent kernel memory into the network skb. Fix this by rejecting block lengths that cannot hold at least the NTB header plus one NDP. This will make block_len - opts->ndp_size and block_len - opts->dpe_size both well-defined. Commit 8d2b1a1ec9f5 ("CDC-NCM: avoid overflow in sanity checking") fixed a related class of issues on the host side of NCM.

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: f_phonet: fix skb frags[] overflow in pn_rx_complete() A broken/bored/mean USB host can overflow the skb_shared_info->frags[] array on a Linux gadget exposing a Phonet function by sending an unbounded sequence of full-page OUT transfers. pn_rx_complete() finalizes the skb only when req->actual < req->length, where req->length is set to PAGE_SIZE by the gadget. If the host always sends exactly PAGE_SIZE bytes per transfer, fp->rx.skb will never be reset and each completion will add another fragment via skb_add_rx_frag(). Once nr_frags exceeds MAX_SKB_FRAGS (default 17), subsequent frag stores overwrite memory adjacent to the shinfo on the heap. Drop the skb and account a length error when the frag limit is reached, matching the fix applied in t7xx by commit f0813bcd2d9d ("net: wwan: t7xx: fix potential skb->frags overflow in RX path").

In the Linux kernel, the following vulnerability has been resolved: x86/platform/uv: Handle deconfigured sockets When a socket is deconfigured, it's mapped to SOCK_EMPTY (0xffff). This causes a panic while allocating UV hub info structures. Fix this by using NUMA_NO_NODE, allowing UV hub info structures to be allocated on valid nodes.

In the Linux kernel, the following vulnerability has been resolved: drm/xe/pxp: Clear restart flag in pxp_start after jumping back If we don't clear the flag we'll keep jumping back at the beginning of the function once we reach the end. (cherry picked from commit 0850ec7bb2459602351639dccf7a68a03c9d1ee0)

In the Linux kernel, the following vulnerability has been resolved: usb: cdns3: gadget: fix NULL pointer dereference in ep_queue When the gadget endpoint is disabled or not yet configured, the ep->desc pointer can be NULL. This leads to a NULL pointer dereference when __cdns3_gadget_ep_queue() is called, causing a kernel crash. Add a check to return -ESHUTDOWN if ep->desc is NULL, which is the standard return code for unconfigured endpoints. This prevents potential crashes when ep_queue is called on endpoints that are not ready.

IBM Common Cryptographic Architecture (CCA 5.x MTM for 4767 and CCA 7.x MTM for 4769) could allow a local user to cause a denial of service due to improper input validation. IBM X-Force ID: 223596.

In the Linux kernel, the following vulnerability has been resolved: hwmon: (occ) Fix division by zero in occ_show_power_1() In occ_show_power_1() case 1, the accumulator is divided by update_tag without checking for zero. If no samples have been collected yet (e.g. during early boot when the sensor block is included but hasn't been updated), update_tag is zero, causing a kernel divide-by-zero crash. The 2019 fix in commit 211186cae14d ("hwmon: (occ) Fix division by zero issue") only addressed occ_get_powr_avg() used by occ_show_power_2() and occ_show_power_a0(). This separate code path in occ_show_power_1() was missed. Fix this by reusing the existing occ_get_powr_avg() helper, which already handles the zero-sample case and uses mul_u64_u32_div() to multiply before dividing for better precision. Move the helper above occ_show_power_1() so it is visible at the call site. [groeck: Fix alignment problems reported by checkpatch]

In the Linux kernel, the following vulnerability has been resolved: PM: sleep: Drop spurious WARN_ON() from pm_restore_gfp_mask() Commit 35e4a69b2003f ("PM: sleep: Allow pm_restrict_gfp_mask() stacking") introduced refcount-based GFP mask management that warns when pm_restore_gfp_mask() is called with saved_gfp_count == 0. Some hibernation paths call pm_restore_gfp_mask() defensively where the GFP mask may or may not be restricted depending on the execution path. For example, the uswsusp interface invokes it in SNAPSHOT_CREATE_IMAGE, SNAPSHOT_UNFREEZE, and snapshot_release(). Before the stacking change this was a silent no-op; it now triggers a spurious WARNING. Remove the WARN_ON() wrapper from the !saved_gfp_count check while retaining the check itself, so that defensive calls remain harmless without producing false warnings. [ rjw: Subject tweak ]

In the Linux kernel, the following vulnerability has been resolved: crypto: af_alg - limit RX SG extraction by receive buffer budget Make af_alg_get_rsgl() limit each RX scatterlist extraction to the remaining receive buffer budget. af_alg_get_rsgl() currently uses af_alg_readable() only as a gate before extracting data into the RX scatterlist. Limit each extraction to the remaining af_alg_rcvbuf(sk) budget so that receive-side accounting matches the amount of data attached to the request. If skcipher cannot obtain enough RX space for at least one chunk while more data remains to be processed, reject the recvmsg call instead of rounding the request length down to zero.

In the Linux kernel, the following vulnerability has been resolved: comedi: ni_atmio16d: Fix invalid clean-up after failed attach If the driver's COMEDI "attach" handler function (`atmio16d_attach()`) returns an error, the COMEDI core will call the driver's "detach" handler function (`atmio16d_detach()`) to clean up. This calls `reset_atmio16d()` unconditionally, but depending on where the error occurred in the attach handler, the device may not have been sufficiently initialized to call `reset_atmio16d()`. It uses `dev->iobase` as the I/O port base address and `dev->private` as the pointer to the COMEDI device's private data structure. `dev->iobase` may still be set to its initial value of 0, which would result in undesired writes to low I/O port addresses. `dev->private` may still be `NULL`, which would result in null pointer dereferences. Fix `atmio16d_detach()` by checking that `dev->private` is valid (non-null) before calling `reset_atmio16d()`. This implies that `dev->iobase` was set correctly since that is set up before `dev->private`.

In the Linux kernel, the following vulnerability has been resolved: ALSA: fireworks: bound device-supplied status before string array lookup The status field in an EFW response is a 32-bit value supplied by the firewire device. efr_status_names[] has 17 entries so a status value outside that range goes off into the weeds when looking at the %s value. Even worse, the status could return EFR_STATUS_INCOMPLETE which is 0x80000000, and is obviously not in that array of potential strings. Fix this up by properly bounding the index against the array size and printing "unknown" if it's not recognized.

In the Linux kernel, the following vulnerability has been resolved: mm/vma: fix memory leak in __mmap_region() commit 605f6586ecf7 ("mm/vma: do not leak memory when .mmap_prepare swaps the file") handled the success path by skipping get_file() via file_doesnt_need_get, but missed the error path. When /dev/zero is mmap'd with MAP_SHARED, mmap_zero_prepare() calls shmem_zero_setup_desc() which allocates a new shmem file to back the mapping. If __mmap_new_vma() subsequently fails, this replacement file is never fput()'d - the original is released by ksys_mmap_pgoff(), but nobody releases the new one. Add fput() for the swapped file in the error path. Reproducible with fault injection. FAULT_INJECTION: forcing a failure. name failslab, interval 1, probability 0, space 0, times 1 CPU: 2 UID: 0 PID: 366 Comm: syz.7.14 Not tainted 7.0.0-rc6 #2 PREEMPT(full) Hardware name: QEMU Ubuntu 24.04 PC v2 (i440FX + PIIX, arch_caps fix, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x164/0x1f0 should_fail_ex+0x525/0x650 should_failslab+0xdf/0x140 kmem_cache_alloc_noprof+0x78/0x630 vm_area_alloc+0x24/0x160 __mmap_region+0xf6b/0x2660 mmap_region+0x2eb/0x3a0 do_mmap+0xc79/0x1240 vm_mmap_pgoff+0x252/0x4c0 ksys_mmap_pgoff+0xf8/0x120 __x64_sys_mmap+0x12a/0x190 do_syscall_64+0xa9/0x580 entry_SYSCALL_64_after_hwframe+0x76/0x7e </TASK> kmemleak: 1 new suspected memory leaks (see /sys/kernel/debug/kmemleak) BUG: memory leak unreferenced object 0xffff8881118aca80 (size 360): comm "syz.7.14", pid 366, jiffies 4294913255 hex dump (first 32 bytes): 00 00 00 00 ad 4e ad de ff ff ff ff 00 00 00 00 .....N.......... ff ff ff ff ff ff ff ff c0 28 4d ae ff ff ff ff .........(M..... backtrace (crc db0f53bc): kmem_cache_alloc_noprof+0x3ab/0x630 alloc_empty_file+0x5a/0x1e0 alloc_file_pseudo+0x135/0x220 __shmem_file_setup+0x274/0x420 shmem_zero_setup_desc+0x9c/0x170 mmap_zero_prepare+0x123/0x140 __mmap_region+0xdda/0x2660 mmap_region+0x2eb/0x3a0 do_mmap+0xc79/0x1240 vm_mmap_pgoff+0x252/0x4c0 ksys_mmap_pgoff+0xf8/0x120 __x64_sys_mmap+0x12a/0x190 do_syscall_64+0xa9/0x580 entry_SYSCALL_64_after_hwframe+0x76/0x7e Found by syzkaller.

In the Linux kernel, the following vulnerability has been resolved: xfrm_user: fix info leak in build_report() struct xfrm_user_report is a __u8 proto field followed by a struct xfrm_selector which means there is three "empty" bytes of padding, but the padding is never zeroed before copying to userspace. Fix that up by zeroing the structure before setting individual member variables.

In the Linux kernel, the following vulnerability has been resolved: bridge: br_nd_send: validate ND option lengths br_nd_send() walks ND options according to option-provided lengths. A malformed option can make the parser advance beyond the computed option span or use a too-short source LLADDR option payload. Validate option lengths against the remaining NS option area before advancing, and only read source LLADDR when the option is large enough for an Ethernet address.

In the Linux kernel, the following vulnerability has been resolved: pmdomain: bcm: bcm2835-power: Increase ASB control timeout The bcm2835_asb_control() function uses a tight polling loop to wait for the ASB bridge to acknowledge a request. During intensive workloads, this handshake intermittently fails for V3D's master ASB on BCM2711, resulting in "Failed to disable ASB master for v3d" errors during runtime PM suspend. As a consequence, the failed power-off leaves V3D in a broken state, leading to bus faults or system hangs on later accesses. As the timeout is insufficient in some scenarios, increase the polling timeout from 1us to 5us, which is still negligible in the context of a power domain transition. Also, replace the open-coded ktime_get_ns()/ cpu_relax() polling loop with readl_poll_timeout_atomic().

In the Linux kernel, the following vulnerability has been resolved: mmc: vub300: fix NULL-deref on disconnect Make sure to deregister the controller before dropping the reference to the driver data on disconnect to avoid NULL-pointer dereferences or use-after-free.

In the Linux kernel, the following vulnerability has been resolved: net: usb: cdc-phonet: fix skb frags[] overflow in rx_complete() A malicious USB device claiming to be a CDC Phonet modem can overflow the skb_shared_info->frags[] array by sending an unbounded sequence of full-page bulk transfers. Drop the skb and increment the length error when the frag limit is reached. This matches the same fix that commit f0813bcd2d9d ("net: wwan: t7xx: fix potential skb->frags overflow in RX path") did for the t7xx driver.

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: u_ether: Fix NULL pointer deref in eth_get_drvinfo Commit ec35c1969650 ("usb: gadget: f_ncm: Fix net_device lifecycle with device_move") reparents the gadget device to /sys/devices/virtual during unbind, clearing the gadget pointer. If the userspace tool queries on the surviving interface during this detached window, this leads to a NULL pointer dereference. Unable to handle kernel NULL pointer dereference Call trace: eth_get_drvinfo+0x50/0x90 ethtool_get_drvinfo+0x5c/0x1f0 __dev_ethtool+0xaec/0x1fe0 dev_ethtool+0x134/0x2e0 dev_ioctl+0x338/0x560 Add a NULL check for dev->gadget in eth_get_drvinfo(). When detached, skip copying the fw_version and bus_info strings, which is natively handled by ethtool_get_drvinfo for empty strings.

In the Linux kernel, the following vulnerability has been resolved: net: lan966x: fix page pool leak in error paths lan966x_fdma_rx_alloc() creates a page pool but does not destroy it if the subsequent fdma_alloc_coherent() call fails, leaking the pool. Similarly, lan966x_fdma_init() frees the coherent DMA memory when lan966x_fdma_tx_alloc() fails but does not destroy the page pool that was successfully created by lan966x_fdma_rx_alloc(), leaking it. Add the missing page_pool_destroy() calls in both error paths.

In the Linux kernel, the following vulnerability has been resolved: PCI: endpoint: pci-epf-vntb: Remove duplicate resource teardown epf_ntb_epc_destroy() duplicates the teardown that the caller is supposed to perform later. This leads to an oops when .allow_link fails or when .drop_link is performed. The following is an example oops of the former case: Unable to handle kernel paging request at virtual address dead000000000108 [...] [dead000000000108] address between user and kernel address ranges Internal error: Oops: 0000000096000044 [#1] SMP [...] Call trace: pci_epc_remove_epf+0x78/0xe0 (P) pci_primary_epc_epf_link+0x88/0xa8 configfs_symlink+0x1f4/0x5a0 vfs_symlink+0x134/0x1d8 do_symlinkat+0x88/0x138 __arm64_sys_symlinkat+0x74/0xe0 [...] Remove the helper, and drop pci_epc_put(). EPC device refcounting is tied to the configfs EPC group lifetime, and pci_epc_put() in the .drop_link path is sufficient.

In the Linux kernel, the following vulnerability has been resolved: drm/xe/xe_pagefault: Disallow writes to read-only VMAs The page fault handler should reject write/atomic access to read only VMAs. Add code to handle this in xe_pagefault_service after the VMA lookup. v2: - Apply max line length (Matthew) (cherry picked from commit 714ee6754ac5fa3dc078856a196a6b124cd797a0)

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: f_hid: move list and spinlock inits from bind to alloc There was an issue when you did the following: - setup and bind an hid gadget - open /dev/hidg0 - use the resulting fd in EPOLL_CTL_ADD - unbind the UDC - bind the UDC - use the fd in EPOLL_CTL_DEL When CONFIG_DEBUG_LIST was enabled, a list_del corruption was reported within remove_wait_queue (via ep_remove_wait_queue). After some debugging I found out that the queues, which f_hid registers via poll_wait were the problem. These were initialized using init_waitqueue_head inside hidg_bind. So effectively, the bind function re-initialized the queues while there were still items in them. The solution is to move the initialization from hidg_bind to hidg_alloc to extend their lifetimes to the lifetime of the function instance. Additionally, I found many other possibly problematic init calls in the bind function, which I moved as well.

In the Linux kernel, the following vulnerability has been resolved: smb: server: make use of smbdirect_socket.send_io.bcredits It turns out that our code will corrupt the stream of reassabled data transfer messages when we trigger an immendiate (empty) send. In order to fix this we'll have a single 'batch' credit per connection. And code getting that credit is free to use as much messages until remaining_length reaches 0, then the batch credit it given back and the next logical send can happen.

In the Linux kernel, the following vulnerability has been resolved: mm/userfaultfd: fix hugetlb fault mutex hash calculation In mfill_atomic_hugetlb(), linear_page_index() is used to calculate the page index for hugetlb_fault_mutex_hash(). However, linear_page_index() returns the index in PAGE_SIZE units, while hugetlb_fault_mutex_hash() expects the index in huge page units. This mismatch means that different addresses within the same huge page can produce different hash values, leading to the use of different mutexes for the same huge page. This can cause races between faulting threads, which can corrupt the reservation map and trigger the BUG_ON in resv_map_release(). Fix this by introducing hugetlb_linear_page_index(), which returns the page index in huge page granularity, and using it in place of linear_page_index().

In the Linux kernel, the following vulnerability has been resolved: KVM: SEV: Drop WARN on large size for KVM_MEMORY_ENCRYPT_REG_REGION Drop the WARN in sev_pin_memory() on npages overflowing an int, as the WARN is comically trivially to trigger from userspace, e.g. by doing: struct kvm_enc_region range = { .addr = 0, .size = -1ul, }; __vm_ioctl(vm, KVM_MEMORY_ENCRYPT_REG_REGION, &range); Note, the checks in sev_mem_enc_register_region() that presumably exist to verify the incoming address+size are completely worthless, as both "addr" and "size" are u64s and SEV is 64-bit only, i.e. they _can't_ be greater than ULONG_MAX. That wart will be cleaned up in the near future. if (range->addr > ULONG_MAX || range->size > ULONG_MAX) return -EINVAL; Opportunistically add a comment to explain why the code calculates the number of pages the "hard" way, e.g. instead of just shifting @ulen.

In the Linux kernel, the following vulnerability has been resolved: net: altera-tse: fix skb leak on DMA mapping error in tse_start_xmit() When dma_map_single() fails in tse_start_xmit(), the function returns NETDEV_TX_OK without freeing the skb. Since NETDEV_TX_OK tells the stack the packet was consumed, the skb is never freed, leaking memory on every DMA mapping failure. Add dev_kfree_skb_any() before returning to properly free the skb.