In the Linux kernel, the following vulnerability has been resolved: objtool, spi: amd: Fix out-of-bounds stack access in amd_set_spi_freq() If speed_hz < AMD_SPI_MIN_HZ, amd_set_spi_freq() iterates over the entire amd_spi_freq array without breaking out early, causing 'i' to go beyond the array bounds. Fix that by stopping the loop when it gets to the last entry, so the low speed_hz value gets clamped up to AMD_SPI_MIN_HZ. Fixes the following warning with an UBSAN kernel: drivers/spi/spi-amd.o: error: objtool: amd_set_spi_freq() falls through to next function amd_spi_set_opcode()

In the Linux kernel, the following vulnerability has been resolved: iio: light: Add check for array bounds in veml6075_read_int_time_ms The array contains only 5 elements, but the index calculated by veml6075_read_int_time_index can range from 0 to 7, which could lead to out-of-bounds access. The check prevents this issue. Coverity Issue CID 1574309: (#1 of 1): Out-of-bounds read (OVERRUN) overrun-local: Overrunning array veml6075_it_ms of 5 4-byte elements at element index 7 (byte offset 31) using index int_index (which evaluates to 7) This is hardening against potentially broken hardware. Good to have but not necessary to backport.

In the Linux kernel, the following vulnerability has been resolved: LoongArch: KVM: Avoid overflow with array index The variable index is modified and reused as array index when modify register EIOINTC_ENABLE. There will be array index overflow problem.

In the Linux kernel, the following vulnerability has been resolved: wifi: rtw89: Fix array index mistake in rtw89_sta_info_get_iter() In rtw89_sta_info_get_iter() 'status->he_gi' is compared to array size. But then 'rate->he_gi' is used as array index instead of 'status->he_gi'. This can lead to go beyond array boundaries in case of 'rate->he_gi' is not equal to 'status->he_gi' and is bigger than array size. Looks like "copy-paste" mistake. Fix this mistake by replacing 'rate->he_gi' with 'status->he_gi'. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: iio: imu: st_lsm6dsx: Set buffer sampling frequency for accelerometer only The st_lsm6dsx_hwfifo_odr_store() function, which is called when userspace writes the buffer sampling frequency sysfs attribute, calls st_lsm6dsx_check_odr(), which accesses the odr_table array at index `sensor->id`; since this array is only 2 entries long, an access for any sensor type other than accelerometer or gyroscope is an out-of-bounds access. The motivation for being able to set a buffer frequency different from the sensor sampling frequency is to support use cases that need accurate event detection (which requires a high sampling frequency) while retrieving sensor data at low frequency. Since all the supported event types are generated from acceleration data only, do not create the buffer sampling frequency attribute for sensor types other than the accelerometer.

In the Linux kernel, the following vulnerability has been resolved: spi: cadence: Fix out-of-bounds array access in cdns_mrvl_xspi_setup_clock() If requested_clk > 128, cdns_mrvl_xspi_setup_clock() iterates over the entire cdns_mrvl_xspi_clk_div_list array without breaking out early, causing 'i' to go beyond the array bounds. Fix that by stopping the loop when it gets to the last entry, clamping the clock to the minimum 6.25 MHz. Fixes the following warning with an UBSAN kernel: vmlinux.o: warning: objtool: cdns_mrvl_xspi_setup_clock: unexpected end of section .text.cdns_mrvl_xspi_setup_clock

In the Linux kernel, the following vulnerability has been resolved: pktgen: Avoid out-of-bounds access in get_imix_entries Passing a sufficient amount of imix entries leads to invalid access to the pkt_dev->imix_entries array because of the incorrect boundary check. UBSAN: array-index-out-of-bounds in net/core/pktgen.c:874:24 index 20 is out of range for type 'imix_pkt [20]' CPU: 2 PID: 1210 Comm: bash Not tainted 6.10.0-rc1 #121 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996) Call Trace: <TASK> dump_stack_lvl lib/dump_stack.c:117 __ubsan_handle_out_of_bounds lib/ubsan.c:429 get_imix_entries net/core/pktgen.c:874 pktgen_if_write net/core/pktgen.c:1063 pde_write fs/proc/inode.c:334 proc_reg_write fs/proc/inode.c:346 vfs_write fs/read_write.c:593 ksys_write fs/read_write.c:644 do_syscall_64 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe arch/x86/entry/entry_64.S:130 Found by Linux Verification Center (linuxtesting.org) with SVACE. [ fp: allow to fill the array completely; minor changelog cleanup ]

In the Linux kernel, the following vulnerability has been resolved: jfs: Fix array-index-out-of-bounds in diFree

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Check index msg_id before read or write [WHAT] msg_id is used as an array index and it cannot be a negative value, and therefore cannot be equal to MOD_HDCP_MESSAGE_ID_INVALID (-1). [HOW] Check whether msg_id is valid before reading and setting. This fixes 4 OVERRUN issues reported by Coverity.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Check pipe offset before setting vblank pipe_ctx has a size of MAX_PIPES so checking its index before accessing the array. This fixes an OVERRUN issue reported by Coverity.

In the Linux kernel, the following vulnerability has been resolved: dev/parport: fix the array out-of-bounds risk Fixed array out-of-bounds issues caused by sprintf by replacing it with snprintf for safer data copying, ensuring the destination buffer is not overflowed. Below is the stack trace I encountered during the actual issue: [ 66.575408s] [pid:5118,cpu4,QThread,4]Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: do_hardware_base_addr+0xcc/0xd0 [parport] [ 66.575408s] [pid:5118,cpu4,QThread,5]CPU: 4 PID: 5118 Comm: QThread Tainted: G S W O 5.10.97-arm64-desktop #7100.57021.2 [ 66.575439s] [pid:5118,cpu4,QThread,6]TGID: 5087 Comm: EFileApp [ 66.575439s] [pid:5118,cpu4,QThread,7]Hardware name: HUAWEI HUAWEI QingYun PGUX-W515x-B081/SP1PANGUXM, BIOS 1.00.07 04/29/2024 [ 66.575439s] [pid:5118,cpu4,QThread,8]Call trace: [ 66.575469s] [pid:5118,cpu4,QThread,9] dump_backtrace+0x0/0x1c0 [ 66.575469s] [pid:5118,cpu4,QThread,0] show_stack+0x14/0x20 [ 66.575469s] [pid:5118,cpu4,QThread,1] dump_stack+0xd4/0x10c [ 66.575500s] [pid:5118,cpu4,QThread,2] panic+0x1d8/0x3bc [ 66.575500s] [pid:5118,cpu4,QThread,3] __stack_chk_fail+0x2c/0x38 [ 66.575500s] [pid:5118,cpu4,QThread,4] do_hardware_base_addr+0xcc/0xd0 [parport]

In the Linux kernel, the following vulnerability has been resolved: gpio: davinci: Validate the obtained number of IRQs Value of pdata->gpio_unbanked is taken from Device Tree. In case of broken DT due to any error this value can be any. Without this value validation there can be out of chips->irqs array boundaries access in davinci_gpio_probe(). Validate the obtained nirq value so that it won't exceed the maximum number of IRQs per bank. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: ASSERT when failing to find index by plane/stream id [WHY] find_disp_cfg_idx_by_plane_id and find_disp_cfg_idx_by_stream_id returns an array index and they return -1 when not found; however, -1 is not a valid index number. [HOW] When this happens, call ASSERT(), and return a positive number (which is fewer than callers' array size) instead. This fixes 4 OVERRUN and 2 NEGATIVE_RETURNS issues reported by Coverity.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix array-index-out-of-bounds in dml2/FCLKChangeSupport [Why] Potential out of bounds access in dml2_calculate_rq_and_dlg_params() because the value of out_lowest_state_idx used as an index for FCLKChangeSupport array can be greater than 1. [How] Currently dml2 core specifies identical values for all FCLKChangeSupport elements. Always use index 0 in the condition to avoid out of bounds access.

In the Linux kernel, the following vulnerability has been resolved: platform/x86: toshiba_acpi: Fix array out-of-bounds access In order to use toshiba_dmi_quirks[] together with the standard DMI matching functions, it must be terminated by a empty entry. Since this entry is missing, an array out-of-bounds access occurs every time the quirk list is processed. Fix this by adding the terminating empty entry.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix potential index out of bounds in color transformation function Fixes index out of bounds issue in the color transformation function. The issue could occur when the index 'i' exceeds the number of transfer function points (TRANSFER_FUNC_POINTS). The fix adds a check to ensure 'i' is within bounds before accessing the transfer function points. If 'i' is out of bounds, an error message is logged and the function returns false to indicate an error. Reported by smatch: drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_cm_common.c:405 cm_helper_translate_curve_to_hw_format() error: buffer overflow 'output_tf->tf_pts.red' 1025 <= s32max drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_cm_common.c:406 cm_helper_translate_curve_to_hw_format() error: buffer overflow 'output_tf->tf_pts.green' 1025 <= s32max drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_cm_common.c:407 cm_helper_translate_curve_to_hw_format() error: buffer overflow 'output_tf->tf_pts.blue' 1025 <= s32max

In the Linux kernel, the following vulnerability has been resolved: iio: adc: PAC1934: fix accessing out of bounds array index Fix accessing out of bounds array index for average current and voltage measurements. The device itself has only 4 channels, but in sysfs there are "fake" channels for the average voltages and currents too.

In the Linux kernel, the following vulnerability has been resolved: drivers/perf: hisi: hns3: Fix out-of-bound access when valid event group The perf tool allows users to create event groups through following cmd [1], but the driver does not check whether the array index is out of bounds when writing data to the event_group array. If the number of events in an event_group is greater than HNS3_PMU_MAX_HW_EVENTS, the memory write overflow of event_group array occurs. Add array index check to fix the possible array out of bounds violation, and return directly when write new events are written to array bounds. There are 9 different events in an event_group. [1] perf stat -e '{pmu/event1/, ... ,pmu/event9/}

In the Linux kernel, the following vulnerability has been resolved: drivers/perf: hisi_pcie: Fix out-of-bound access when valid event group The perf tool allows users to create event groups through following cmd [1], but the driver does not check whether the array index is out of bounds when writing data to the event_group array. If the number of events in an event_group is greater than HISI_PCIE_MAX_COUNTERS, the memory write overflow of event_group array occurs. Add array index check to fix the possible array out of bounds violation, and return directly when write new events are written to array bounds. There are 9 different events in an event_group. [1] perf stat -e '{pmu/event1/, ... ,pmu/event9/}'

In the Linux kernel, the following vulnerability has been resolved: wifi: nl80211: Avoid address calculations via out of bounds array indexing Before request->channels[] can be used, request->n_channels must be set. Additionally, address calculations for memory after the "channels" array need to be calculated from the allocation base ("request") rather than via the first "out of bounds" index of "channels", otherwise run-time bounds checking will throw a warning.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Add a timeout to acquire the command queue semaphore Prevent forced completion handling on an entry that has not yet been assigned an index, causing an out of bounds access on idx = -22. Instead of waiting indefinitely for the sem, blocking flow now waits for index to be allocated or a sem acquisition timeout before beginning the timer for FW completion. Kernel log example: mlx5_core 0000:06:00.0: wait_func_handle_exec_timeout:1128:(pid 185911): cmd[-22]: CREATE_UCTX(0xa04) No done completion

In the Linux kernel, the following vulnerability has been resolved: wifi: rtlwifi: 8192cu: fix tid out of range in rtl92cu_tx_fill_desc() TID getting from ieee80211_get_tid() might be out of range of array size of sta_entry->tids[], so check TID is less than MAX_TID_COUNT. Othwerwise, UBSAN warn: UBSAN: array-index-out-of-bounds in drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:514:30 index 10 is out of range for type 'rtl_tid_data [9]'

In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: mvm: guard against invalid STA ID on removal Guard against invalid station IDs in iwl_mvm_mld_rm_sta_id as that would result in out-of-bounds array accesses. This prevents issues should the driver get into a bad state during error handling.

In the Linux kernel, the following vulnerability has been resolved: ASoC: mediatek: mt8195: Add platform entry for ETDM1_OUT_BE dai link Commit e70b8dd26711 ("ASoC: mediatek: mt8195: Remove afe-dai component and rework codec link") removed the codec entry for the ETDM1_OUT_BE dai link entirely instead of replacing it with COMP_EMPTY(). This worked by accident as the remaining COMP_EMPTY() platform entry became the codec entry, and the platform entry became completely empty, effectively the same as COMP_DUMMY() since snd_soc_fill_dummy_dai() doesn't do anything for platform entries. This causes a KASAN out-of-bounds warning in mtk_soundcard_common_probe() in sound/soc/mediatek/common/mtk-soundcard-driver.c: for_each_card_prelinks(card, i, dai_link) { if (adsp_node && !strncmp(dai_link->name, "AFE_SOF", strlen("AFE_SOF"))) dai_link->platforms->of_node = adsp_node; else if (!dai_link->platforms->name && !dai_link->platforms->of_node) dai_link->platforms->of_node = platform_node; } where the code expects the platforms array to have space for at least one entry. Add an COMP_EMPTY() entry so that dai_link->platforms has space.

In the Linux kernel, the following vulnerability has been resolved: bpf: Protect against int overflow for stack access size This patch re-introduces protection against the size of access to stack memory being negative; the access size can appear negative as a result of overflowing its signed int representation. This should not actually happen, as there are other protections along the way, but we should protect against it anyway. One code path was missing such protections (fixed in the previous patch in the series), causing out-of-bounds array accesses in check_stack_range_initialized(). This patch causes the verification of a program with such a non-sensical access size to fail. This check used to exist in a more indirect way, but was inadvertendly removed in a833a17aeac7.

The sanity_check_ckpt function in fs/f2fs/super.c in the Linux kernel before 4.12.4 does not validate the blkoff and segno arrays, which allows local users to gain privileges via unspecified vectors.

In the Linux kernel, the following vulnerability has been resolved: bnx2x: Fix multiple UBSAN array-index-out-of-bounds Fix UBSAN warnings that occur when using a system with 32 physical cpu cores or more, or when the user defines a number of Ethernet queues greater than or equal to FP_SB_MAX_E1x using the num_queues module parameter. Currently there is a read/write out of bounds that occurs on the array "struct stats_query_entry query" present inside the "bnx2x_fw_stats_req" struct in "drivers/net/ethernet/broadcom/bnx2x/bnx2x.h". Looking at the definition of the "struct stats_query_entry query" array: struct stats_query_entry query[FP_SB_MAX_E1x+ BNX2X_FIRST_QUEUE_QUERY_IDX]; FP_SB_MAX_E1x is defined as the maximum number of fast path interrupts and has a value of 16, while BNX2X_FIRST_QUEUE_QUERY_IDX has a value of 3 meaning the array has a total size of 19. Since accesses to "struct stats_query_entry query" are offset-ted by BNX2X_FIRST_QUEUE_QUERY_IDX, that means that the total number of Ethernet queues should not exceed FP_SB_MAX_E1x (16). However one of these queues is reserved for FCOE and thus the number of Ethernet queues should be set to [FP_SB_MAX_E1x -1] (15) if FCOE is enabled or [FP_SB_MAX_E1x] (16) if it is not. This is also described in a comment in the source code in drivers/net/ethernet/broadcom/bnx2x/bnx2x.h just above the Macro definition of FP_SB_MAX_E1x. Below is the part of this explanation that it important for this patch /* * The total number of L2 queues, MSIX vectors and HW contexts (CIDs) is * control by the number of fast-path status blocks supported by the * device (HW/FW). Each fast-path status block (FP-SB) aka non-default * status block represents an independent interrupts context that can * serve a regular L2 networking queue. However special L2 queues such * as the FCoE queue do not require a FP-SB and other components like * the CNIC may consume FP-SB reducing the number of possible L2 queues * * If the maximum number of FP-SB available is X then: * a. If CNIC is supported it consumes 1 FP-SB thus the max number of * regular L2 queues is Y=X-1 * b. In MF mode the actual number of L2 queues is Y= (X-1/MF_factor) * c. If the FCoE L2 queue is supported the actual number of L2 queues * is Y+1 * d. The number of irqs (MSIX vectors) is either Y+1 (one extra for * slow-path interrupts) or Y+2 if CNIC is supported (one additional * FP interrupt context for the CNIC). * e. The number of HW context (CID count) is always X or X+1 if FCoE * L2 queue is supported. The cid for the FCoE L2 queue is always X. */ However this driver also supports NICs that use the E2 controller which can handle more queues due to having more FP-SB represented by FP_SB_MAX_E2. Looking at the commits when the E2 support was added, it was originally using the E1x parameters: commit f2e0899f0f27 ("bnx2x: Add 57712 support"). Back then FP_SB_MAX_E2 was set to 16 the same as E1x. However the driver was later updated to take full advantage of the E2 instead of having it be limited to the capabilities of the E1x. But as far as we can tell, the array "stats_query_entry query" was still limited to using the FP-SB available to the E1x cards as part of an oversignt when the driver was updated to take full advantage of the E2, and now with the driver being aware of the greater queue size supported by E2 NICs, it causes the UBSAN warnings seen in the stack traces below. This patch increases the size of the "stats_query_entry query" array by replacing FP_SB_MAX_E1x with FP_SB_MAX_E2 to be large enough to handle both types of NICs. Stack traces: UBSAN: array-index-out-of-bounds in drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c:1529:11 index 20 is out of range for type 'stats_query_entry [19]' CPU: 12 PID: 858 Comm: systemd-network Not tainted 6.9.0-060900rc7-generic #202405052133 Hardware name: HP ProLiant DL360 Gen9/ProLiant DL360 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix OOB in nilfs_set_de_type The size of the nilfs_type_by_mode array in the fs/nilfs2/dir.c file is defined as "S_IFMT >> S_SHIFT", but the nilfs_set_de_type() function, which uses this array, specifies the index to read from the array in the same way as "(mode & S_IFMT) >> S_SHIFT". static void nilfs_set_de_type(struct nilfs_dir_entry *de, struct inode *inode) { umode_t mode = inode->i_mode; de->file_type = nilfs_type_by_mode[(mode & S_IFMT)>>S_SHIFT]; // oob } However, when the index is determined this way, an out-of-bounds (OOB) error occurs by referring to an index that is 1 larger than the array size when the condition "mode & S_IFMT == S_IFMT" is satisfied. Therefore, a patch to resize the nilfs_type_by_mode array should be applied to prevent OOB errors.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: fix incorrect mpc_combine array size [why] MAX_SURFACES is per stream, while MAX_PLANES is per asic. The mpc_combine is an array that records all the planes per asic. Therefore MAX_PLANES should be used as the array size. Using MAX_SURFACES causes array overflow when there are more than 3 planes. [how] Use the MAX_PLANES for the mpc_combine array size.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix array-index-out-of-bounds in dcn35_clkmgr [Why] There is a potential memory access violation while iterating through array of dcn35 clks. [How] Limit iteration per array size.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix out-of-bounds access in 'dcn21_link_encoder_create' An issue was identified in the dcn21_link_encoder_create function where an out-of-bounds access could occur when the hpd_source index was used to reference the link_enc_hpd_regs array. This array has a fixed size and the index was not being checked against the array's bounds before accessing it. This fix adds a conditional check to ensure that the hpd_source index is within the valid range of the link_enc_hpd_regs array. If the index is out of bounds, the function now returns NULL to prevent undefined behavior. References: [ 65.920507] ------------[ cut here ]------------ [ 65.920510] UBSAN: array-index-out-of-bounds in drivers/gpu/drm/amd/amdgpu/../display/dc/resource/dcn21/dcn21_resource.c:1312:29 [ 65.920519] index 7 is out of range for type 'dcn10_link_enc_hpd_registers [5]' [ 65.920523] CPU: 3 PID: 1178 Comm: modprobe Tainted: G OE 6.8.0-cleanershaderfeatureresetasdntipmi200nv2132 #13 [ 65.920525] Hardware name: AMD Majolica-RN/Majolica-RN, BIOS WMJ0429N_Weekly_20_04_2 04/29/2020 [ 65.920527] Call Trace: [ 65.920529] <TASK> [ 65.920532] dump_stack_lvl+0x48/0x70 [ 65.920541] dump_stack+0x10/0x20 [ 65.920543] __ubsan_handle_out_of_bounds+0xa2/0xe0 [ 65.920549] dcn21_link_encoder_create+0xd9/0x140 [amdgpu] [ 65.921009] link_create+0x6d3/0xed0 [amdgpu] [ 65.921355] create_links+0x18a/0x4e0 [amdgpu] [ 65.921679] dc_create+0x360/0x720 [amdgpu] [ 65.921999] ? dmi_matches+0xa0/0x220 [ 65.922004] amdgpu_dm_init+0x2b6/0x2c90 [amdgpu] [ 65.922342] ? console_unlock+0x77/0x120 [ 65.922348] ? dev_printk_emit+0x86/0xb0 [ 65.922354] dm_hw_init+0x15/0x40 [amdgpu] [ 65.922686] amdgpu_device_init+0x26a8/0x33a0 [amdgpu] [ 65.922921] amdgpu_driver_load_kms+0x1b/0xa0 [amdgpu] [ 65.923087] amdgpu_pci_probe+0x1b7/0x630 [amdgpu] [ 65.923087] local_pci_probe+0x4b/0xb0 [ 65.923087] pci_device_probe+0xc8/0x280 [ 65.923087] really_probe+0x187/0x300 [ 65.923087] __driver_probe_device+0x85/0x130 [ 65.923087] driver_probe_device+0x24/0x110 [ 65.923087] __driver_attach+0xac/0x1d0 [ 65.923087] ? __pfx___driver_attach+0x10/0x10 [ 65.923087] bus_for_each_dev+0x7d/0xd0 [ 65.923087] driver_attach+0x1e/0x30 [ 65.923087] bus_add_driver+0xf2/0x200 [ 65.923087] driver_register+0x64/0x130 [ 65.923087] ? __pfx_amdgpu_init+0x10/0x10 [amdgpu] [ 65.923087] __pci_register_driver+0x61/0x70 [ 65.923087] amdgpu_init+0x7d/0xff0 [amdgpu] [ 65.923087] do_one_initcall+0x49/0x310 [ 65.923087] ? kmalloc_trace+0x136/0x360 [ 65.923087] do_init_module+0x6a/0x270 [ 65.923087] load_module+0x1fce/0x23a0 [ 65.923087] init_module_from_file+0x9c/0xe0 [ 65.923087] ? init_module_from_file+0x9c/0xe0 [ 65.923087] idempotent_init_module+0x179/0x230 [ 65.923087] __x64_sys_finit_module+0x5d/0xa0 [ 65.923087] do_syscall_64+0x76/0x120 [ 65.923087] entry_SYSCALL_64_after_hwframe+0x6e/0x76 [ 65.923087] RIP: 0033:0x7f2d80f1e88d [ 65.923087] Code: 5b 41 5c c3 66 0f 1f 84 00 00 00 00 00 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 73 b5 0f 00 f7 d8 64 89 01 48 [ 65.923087] RSP: 002b:00007ffc7bc1aa78 EFLAGS: 00000246 ORIG_RAX: 0000000000000139 [ 65.923087] RAX: ffffffffffffffda RBX: 0000564c9c1db130 RCX: 00007f2d80f1e88d [ 65.923087] RDX: 0000000000000000 RSI: 0000564c9c1e5480 RDI: 000000000000000f [ 65.923087] RBP: 0000000000040000 R08: 0000000000000000 R09: 0000000000000002 [ 65.923087] R10: 000000000000000f R11: 0000000000000246 R12: 0000564c9c1e5480 [ 65.923087] R13: 0000564c9c1db260 R14: 0000000000000000 R15: 0000564c9c1e54b0 [ 65.923087] </TASK> [ 65.923927] ---[ end trace ]---

In the Linux kernel, the following vulnerability has been resolved: ppdev: Add an error check in register_device In register_device, the return value of ida_simple_get is unchecked, in witch ida_simple_get will use an invalid index value. To address this issue, index should be checked after ida_simple_get. When the index value is abnormal, a warning message should be printed, the port should be dropped, and the value should be recorded.

NVIDIA GPU Display Driver for Linux contains a vulnerability in the kernel mode layer (nvidia.ko), where an out-of-bounds array access may lead to denial of service, information disclosure, or data tampering.

NVIDIA GPU Display Driver for Linux contains a vulnerability in the kernel mode layer (nvidia.ko), where an out-of-bounds array access may lead to denial of service, data tampering, or information disclosure.

In the Linux kernel, the following vulnerability has been resolved: KVM: x86: use array_index_nospec with indices that come from guest min and dest_id are guest-controlled indices. Using array_index_nospec() after the bounds checks clamps these values to mitigate speculative execution side-channels.

In the Linux kernel, the following vulnerability has been resolved: net: openvswitch: Fix the dead loop of MPLS parse The unexpected MPLS packet may not end with the bottom label stack. When there are many stacks, The label count value has wrapped around. A dead loop occurs, soft lockup/CPU stuck finally. stack backtrace: UBSAN: array-index-out-of-bounds in /build/linux-0Pa0xK/linux-5.15.0/net/openvswitch/flow.c:662:26 index -1 is out of range for type '__be32 [3]' CPU: 34 PID: 0 Comm: swapper/34 Kdump: loaded Tainted: G OE 5.15.0-121-generic #131-Ubuntu Hardware name: Dell Inc. PowerEdge C6420/0JP9TF, BIOS 2.12.2 07/14/2021 Call Trace: <IRQ> show_stack+0x52/0x5c dump_stack_lvl+0x4a/0x63 dump_stack+0x10/0x16 ubsan_epilogue+0x9/0x36 __ubsan_handle_out_of_bounds.cold+0x44/0x49 key_extract_l3l4+0x82a/0x840 [openvswitch] ? kfree_skbmem+0x52/0xa0 key_extract+0x9c/0x2b0 [openvswitch] ovs_flow_key_extract+0x124/0x350 [openvswitch] ovs_vport_receive+0x61/0xd0 [openvswitch] ? kernel_init_free_pages.part.0+0x4a/0x70 ? get_page_from_freelist+0x353/0x540 netdev_port_receive+0xc4/0x180 [openvswitch] ? netdev_port_receive+0x180/0x180 [openvswitch] netdev_frame_hook+0x1f/0x40 [openvswitch] __netif_receive_skb_core.constprop.0+0x23a/0xf00 __netif_receive_skb_list_core+0xfa/0x240 netif_receive_skb_list_internal+0x18e/0x2a0 napi_complete_done+0x7a/0x1c0 bnxt_poll+0x155/0x1c0 [bnxt_en] __napi_poll+0x30/0x180 net_rx_action+0x126/0x280 ? bnxt_msix+0x67/0x80 [bnxt_en] handle_softirqs+0xda/0x2d0 irq_exit_rcu+0x96/0xc0 common_interrupt+0x8e/0xa0 </IRQ>

In the Linux kernel, the following vulnerability has been resolved: fbcon: Make sure modelist not set on unregistered console It looks like attempting to write to the "store_modes" sysfs node will run afoul of unregistered consoles: UBSAN: array-index-out-of-bounds in drivers/video/fbdev/core/fbcon.c:122:28 index -1 is out of range for type 'fb_info *[32]' ... fbcon_info_from_console+0x192/0x1a0 drivers/video/fbdev/core/fbcon.c:122 fbcon_new_modelist+0xbf/0x2d0 drivers/video/fbdev/core/fbcon.c:3048 fb_new_modelist+0x328/0x440 drivers/video/fbdev/core/fbmem.c:673 store_modes+0x1c9/0x3e0 drivers/video/fbdev/core/fbsysfs.c:113 dev_attr_store+0x55/0x80 drivers/base/core.c:2439 static struct fb_info *fbcon_registered_fb[FB_MAX]; ... static signed char con2fb_map[MAX_NR_CONSOLES]; ... static struct fb_info *fbcon_info_from_console(int console) ... return fbcon_registered_fb[con2fb_map[console]]; If con2fb_map contains a -1 things go wrong here. Instead, return NULL, as callers of fbcon_info_from_console() are trying to compare against existing "info" pointers, so error handling should kick in correctly.

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: Set n_channels after allocating struct cfg80211_scan_request Make sure that n_channels is set after allocating the struct cfg80211_registered_device::int_scan_req member. Seen with syzkaller: UBSAN: array-index-out-of-bounds in net/mac80211/scan.c:1208:5 index 0 is out of range for type 'struct ieee80211_channel *[] __counted_by(n_channels)' (aka 'struct ieee80211_channel *[]') This was missed in the initial conversions because I failed to locate the allocation likely due to the "sizeof(void *)" not matching the "channels" array type.

In the Linux kernel, the following vulnerability has been resolved: jfs: upper bound check of tree index in dbAllocAG When computing the tree index in dbAllocAG, we never check if we are out of bounds realative to the size of the stree. This could happen in a scenario where the filesystem metadata are corrupted.

In the Linux kernel, the following vulnerability has been resolved: net: sched: fix ets qdisc OOB Indexing Haowei Yan <g1042620637@gmail.com> found that ets_class_from_arg() can index an Out-Of-Bound class in ets_class_from_arg() when passed clid of 0. The overflow may cause local privilege escalation. [ 18.852298] ------------[ cut here ]------------ [ 18.853271] UBSAN: array-index-out-of-bounds in net/sched/sch_ets.c:93:20 [ 18.853743] index 18446744073709551615 is out of range for type 'ets_class [16]' [ 18.854254] CPU: 0 UID: 0 PID: 1275 Comm: poc Not tainted 6.12.6-dirty #17 [ 18.854821] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 [ 18.856532] Call Trace: [ 18.857441] <TASK> [ 18.858227] dump_stack_lvl+0xc2/0xf0 [ 18.859607] dump_stack+0x10/0x20 [ 18.860908] __ubsan_handle_out_of_bounds+0xa7/0xf0 [ 18.864022] ets_class_change+0x3d6/0x3f0 [ 18.864322] tc_ctl_tclass+0x251/0x910 [ 18.864587] ? lock_acquire+0x5e/0x140 [ 18.865113] ? __mutex_lock+0x9c/0xe70 [ 18.866009] ? __mutex_lock+0xa34/0xe70 [ 18.866401] rtnetlink_rcv_msg+0x170/0x6f0 [ 18.866806] ? __lock_acquire+0x578/0xc10 [ 18.867184] ? __pfx_rtnetlink_rcv_msg+0x10/0x10 [ 18.867503] netlink_rcv_skb+0x59/0x110 [ 18.867776] rtnetlink_rcv+0x15/0x30 [ 18.868159] netlink_unicast+0x1c3/0x2b0 [ 18.868440] netlink_sendmsg+0x239/0x4b0 [ 18.868721] ____sys_sendmsg+0x3e2/0x410 [ 18.869012] ___sys_sendmsg+0x88/0xe0 [ 18.869276] ? rseq_ip_fixup+0x198/0x260 [ 18.869563] ? rseq_update_cpu_node_id+0x10a/0x190 [ 18.869900] ? trace_hardirqs_off+0x5a/0xd0 [ 18.870196] ? syscall_exit_to_user_mode+0xcc/0x220 [ 18.870547] ? do_syscall_64+0x93/0x150 [ 18.870821] ? __memcg_slab_free_hook+0x69/0x290 [ 18.871157] __sys_sendmsg+0x69/0xd0 [ 18.871416] __x64_sys_sendmsg+0x1d/0x30 [ 18.871699] x64_sys_call+0x9e2/0x2670 [ 18.871979] do_syscall_64+0x87/0x150 [ 18.873280] ? do_syscall_64+0x93/0x150 [ 18.874742] ? lock_release+0x7b/0x160 [ 18.876157] ? do_user_addr_fault+0x5ce/0x8f0 [ 18.877833] ? irqentry_exit_to_user_mode+0xc2/0x210 [ 18.879608] ? irqentry_exit+0x77/0xb0 [ 18.879808] ? clear_bhb_loop+0x15/0x70 [ 18.880023] ? clear_bhb_loop+0x15/0x70 [ 18.880223] ? clear_bhb_loop+0x15/0x70 [ 18.880426] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 18.880683] RIP: 0033:0x44a957 [ 18.880851] Code: ff ff e8 fc 00 00 00 66 2e 0f 1f 84 00 00 00 00 00 66 90 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 89 54 24 1c 48 8974 24 10 [ 18.881766] RSP: 002b:00007ffcdd00fad8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e [ 18.882149] RAX: ffffffffffffffda RBX: 00007ffcdd010db8 RCX: 000000000044a957 [ 18.882507] RDX: 0000000000000000 RSI: 00007ffcdd00fb70 RDI: 0000000000000003 [ 18.885037] RBP: 00007ffcdd010bc0 R08: 000000000703c770 R09: 000000000703c7c0 [ 18.887203] R10: 0000000000000080 R11: 0000000000000246 R12: 0000000000000001 [ 18.888026] R13: 00007ffcdd010da8 R14: 00000000004ca7d0 R15: 0000000000000001 [ 18.888395] </TASK> [ 18.888610] ---[ end trace ]---

In the Linux kernel, the following vulnerability has been resolved: mt76: mt7921: fix possible AOOB issue in mt7921_mcu_tx_rate_report Fix possible array out of bound access in mt7921_mcu_tx_rate_report. Remove unnecessary varibable in mt7921_mcu_tx_rate_report

In the Linux kernel, the following vulnerability has been resolved: kyber: fix out of bounds access when preempted __blk_mq_sched_bio_merge() gets the ctx and hctx for the current CPU and passes the hctx to ->bio_merge(). kyber_bio_merge() then gets the ctx for the current CPU again and uses that to get the corresponding Kyber context in the passed hctx. However, the thread may be preempted between the two calls to blk_mq_get_ctx(), and the ctx returned the second time may no longer correspond to the passed hctx. This "works" accidentally most of the time, but it can cause us to read garbage if the second ctx came from an hctx with more ctx's than the first one (i.e., if ctx->index_hw[hctx->type] > hctx->nr_ctx). This manifested as this UBSAN array index out of bounds error reported by Jakub: UBSAN: array-index-out-of-bounds in ../kernel/locking/qspinlock.c:130:9 index 13106 is out of range for type 'long unsigned int [128]' Call Trace: dump_stack+0xa4/0xe5 ubsan_epilogue+0x5/0x40 __ubsan_handle_out_of_bounds.cold.13+0x2a/0x34 queued_spin_lock_slowpath+0x476/0x480 do_raw_spin_lock+0x1c2/0x1d0 kyber_bio_merge+0x112/0x180 blk_mq_submit_bio+0x1f5/0x1100 submit_bio_noacct+0x7b0/0x870 submit_bio+0xc2/0x3a0 btrfs_map_bio+0x4f0/0x9d0 btrfs_submit_data_bio+0x24e/0x310 submit_one_bio+0x7f/0xb0 submit_extent_page+0xc4/0x440 __extent_writepage_io+0x2b8/0x5e0 __extent_writepage+0x28d/0x6e0 extent_write_cache_pages+0x4d7/0x7a0 extent_writepages+0xa2/0x110 do_writepages+0x8f/0x180 __writeback_single_inode+0x99/0x7f0 writeback_sb_inodes+0x34e/0x790 __writeback_inodes_wb+0x9e/0x120 wb_writeback+0x4d2/0x660 wb_workfn+0x64d/0xa10 process_one_work+0x53a/0xa80 worker_thread+0x69/0x5b0 kthread+0x20b/0x240 ret_from_fork+0x1f/0x30 Only Kyber uses the hctx, so fix it by passing the request_queue to ->bio_merge() instead. BFQ and mq-deadline just use that, and Kyber can map the queues itself to avoid the mismatch.

In the Linux kernel, the following vulnerability has been resolved: rtw88: Fix array overrun in rtw_get_tx_power_params() Using a kernel with the Undefined Behaviour Sanity Checker (UBSAN) enabled, the following array overrun is logged: ================================================================================ UBSAN: array-index-out-of-bounds in /home/finger/wireless-drivers-next/drivers/net/wireless/realtek/rtw88/phy.c:1789:34 index 5 is out of range for type 'u8 [5]' CPU: 2 PID: 84 Comm: kworker/u16:3 Tainted: G O 5.12.0-rc5-00086-gd88bba47038e-dirty #651 Hardware name: TOSHIBA TECRA A50-A/TECRA A50-A, BIOS Version 4.50 09/29/2014 Workqueue: phy0 ieee80211_scan_work [mac80211] Call Trace: dump_stack+0x64/0x7c ubsan_epilogue+0x5/0x40 __ubsan_handle_out_of_bounds.cold+0x43/0x48 rtw_get_tx_power_params+0x83a/drivers/net/wireless/realtek/rtw88/0xad0 [rtw_core] ? rtw_pci_read16+0x20/0x20 [rtw_pci] ? check_hw_ready+0x50/0x90 [rtw_core] rtw_phy_get_tx_power_index+0x4d/0xd0 [rtw_core] rtw_phy_set_tx_power_level+0xee/0x1b0 [rtw_core] rtw_set_channel+0xab/0x110 [rtw_core] rtw_ops_config+0x87/0xc0 [rtw_core] ieee80211_hw_config+0x9d/0x130 [mac80211] ieee80211_scan_state_set_channel+0x81/0x170 [mac80211] ieee80211_scan_work+0x19f/0x2a0 [mac80211] process_one_work+0x1dd/0x3a0 worker_thread+0x49/0x330 ? rescuer_thread+0x3a0/0x3a0 kthread+0x134/0x150 ? kthread_create_worker_on_cpu+0x70/0x70 ret_from_fork+0x22/0x30 ================================================================================ The statement where an array is being overrun is shown in the following snippet: if (rate <= DESC_RATE11M) tx_power = pwr_idx_2g->cck_base[group]; else ====> tx_power = pwr_idx_2g->bw40_base[group]; The associated arrays are defined in main.h as follows: struct rtw_2g_txpwr_idx { u8 cck_base[6]; u8 bw40_base[5]; struct rtw_2g_1s_pwr_idx_diff ht_1s_diff; struct rtw_2g_ns_pwr_idx_diff ht_2s_diff; struct rtw_2g_ns_pwr_idx_diff ht_3s_diff; struct rtw_2g_ns_pwr_idx_diff ht_4s_diff; }; The problem arises because the value of group is 5 for channel 14. The trivial increase in the dimension of bw40_base fails as this struct must match the layout of efuse. The fix is to add the rate as an argument to rtw_get_channel_group() and set the group for channel 14 to 4 if rate <= DESC_RATE11M. This patch fixes commit fa6dfe6bff24 ("rtw88: resolve order of tx power setting routines")

In the Linux kernel, the following vulnerability has been resolved: isdn: cpai: check ctr->cnr to avoid array index out of bound The cmtp_add_connection() would add a cmtp session to a controller and run a kernel thread to process cmtp. __module_get(THIS_MODULE); session->task = kthread_run(cmtp_session, session, "kcmtpd_ctr_%d", session->num); During this process, the kernel thread would call detach_capi_ctr() to detach a register controller. if the controller was not attached yet, detach_capi_ctr() would trigger an array-index-out-bounds bug. [ 46.866069][ T6479] UBSAN: array-index-out-of-bounds in drivers/isdn/capi/kcapi.c:483:21 [ 46.867196][ T6479] index -1 is out of range for type 'capi_ctr *[32]' [ 46.867982][ T6479] CPU: 1 PID: 6479 Comm: kcmtpd_ctr_0 Not tainted 5.15.0-rc2+ #8 [ 46.869002][ T6479] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-2 04/01/2014 [ 46.870107][ T6479] Call Trace: [ 46.870473][ T6479] dump_stack_lvl+0x57/0x7d [ 46.870974][ T6479] ubsan_epilogue+0x5/0x40 [ 46.871458][ T6479] __ubsan_handle_out_of_bounds.cold+0x43/0x48 [ 46.872135][ T6479] detach_capi_ctr+0x64/0xc0 [ 46.872639][ T6479] cmtp_session+0x5c8/0x5d0 [ 46.873131][ T6479] ? __init_waitqueue_head+0x60/0x60 [ 46.873712][ T6479] ? cmtp_add_msgpart+0x120/0x120 [ 46.874256][ T6479] kthread+0x147/0x170 [ 46.874709][ T6479] ? set_kthread_struct+0x40/0x40 [ 46.875248][ T6479] ret_from_fork+0x1f/0x30 [ 46.875773][ T6479]

In the Linux kernel, the following vulnerability has been resolved: jfs: fix array-index-out-of-bounds in diNewExt [Syz report] UBSAN: array-index-out-of-bounds in fs/jfs/jfs_imap.c:2360:2 index -878706688 is out of range for type 'struct iagctl[128]' CPU: 1 PID: 5065 Comm: syz-executor282 Not tainted 6.7.0-rc4-syzkaller-00009-gbee0e7762ad2 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 11/10/2023 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x1e7/0x2d0 lib/dump_stack.c:106 ubsan_epilogue lib/ubsan.c:217 [inline] __ubsan_handle_out_of_bounds+0x11c/0x150 lib/ubsan.c:348 diNewExt+0x3cf3/0x4000 fs/jfs/jfs_imap.c:2360 diAllocExt fs/jfs/jfs_imap.c:1949 [inline] diAllocAG+0xbe8/0x1e50 fs/jfs/jfs_imap.c:1666 diAlloc+0x1d3/0x1760 fs/jfs/jfs_imap.c:1587 ialloc+0x8f/0x900 fs/jfs/jfs_inode.c:56 jfs_mkdir+0x1c5/0xb90 fs/jfs/namei.c:225 vfs_mkdir+0x2f1/0x4b0 fs/namei.c:4106 do_mkdirat+0x264/0x3a0 fs/namei.c:4129 __do_sys_mkdir fs/namei.c:4149 [inline] __se_sys_mkdir fs/namei.c:4147 [inline] __x64_sys_mkdir+0x6e/0x80 fs/namei.c:4147 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x45/0x110 arch/x86/entry/common.c:82 entry_SYSCALL_64_after_hwframe+0x63/0x6b RIP: 0033:0x7fcb7e6a0b57 Code: ff ff 77 07 31 c0 c3 0f 1f 40 00 48 c7 c2 b8 ff ff ff f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 b8 53 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007ffd83023038 EFLAGS: 00000286 ORIG_RAX: 0000000000000053 RAX: ffffffffffffffda RBX: 00000000ffffffff RCX: 00007fcb7e6a0b57 RDX: 00000000000a1020 RSI: 00000000000001ff RDI: 0000000020000140 RBP: 0000000020000140 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000286 R12: 00007ffd830230d0 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 [Analysis] When the agstart is too large, it can cause agno overflow. [Fix] After obtaining agno, if the value is invalid, exit the subsequent process. Modified the test from agno > MAXAG to agno >= MAXAG based on linux-next report by kernel test robot (Dan Carpenter).

In the Linux kernel, the following vulnerability has been resolved: fs: jfs: Fix UBSAN: array-index-out-of-bounds in dbAllocDmapLev Syzkaller reported the following issue: UBSAN: array-index-out-of-bounds in fs/jfs/jfs_dmap.c:1965:6 index -84 is out of range for type 's8[341]' (aka 'signed char[341]') CPU: 1 PID: 4995 Comm: syz-executor146 Not tainted 6.4.0-rc6-syzkaller-00037-gb6dad5178cea #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/27/2023 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x1e7/0x2d0 lib/dump_stack.c:106 ubsan_epilogue lib/ubsan.c:217 [inline] __ubsan_handle_out_of_bounds+0x11c/0x150 lib/ubsan.c:348 dbAllocDmapLev+0x3e5/0x430 fs/jfs/jfs_dmap.c:1965 dbAllocCtl+0x113/0x920 fs/jfs/jfs_dmap.c:1809 dbAllocAG+0x28f/0x10b0 fs/jfs/jfs_dmap.c:1350 dbAlloc+0x658/0xca0 fs/jfs/jfs_dmap.c:874 dtSplitUp fs/jfs/jfs_dtree.c:974 [inline] dtInsert+0xda7/0x6b00 fs/jfs/jfs_dtree.c:863 jfs_create+0x7b6/0xbb0 fs/jfs/namei.c:137 lookup_open fs/namei.c:3492 [inline] open_last_lookups fs/namei.c:3560 [inline] path_openat+0x13df/0x3170 fs/namei.c:3788 do_filp_open+0x234/0x490 fs/namei.c:3818 do_sys_openat2+0x13f/0x500 fs/open.c:1356 do_sys_open fs/open.c:1372 [inline] __do_sys_openat fs/open.c:1388 [inline] __se_sys_openat fs/open.c:1383 [inline] __x64_sys_openat+0x247/0x290 fs/open.c:1383 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd RIP: 0033:0x7f1f4e33f7e9 Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 51 14 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007ffc21129578 EFLAGS: 00000246 ORIG_RAX: 0000000000000101 RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f1f4e33f7e9 RDX: 000000000000275a RSI: 0000000020000040 RDI: 00000000ffffff9c RBP: 00007f1f4e2ff080 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f1f4e2ff110 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 </TASK> The bug occurs when the dbAllocDmapLev()function attempts to access dp->tree.stree[leafidx + LEAFIND] while the leafidx value is negative. To rectify this, the patch introduces a safeguard within the dbAllocDmapLev() function. A check has been added to verify if leafidx is negative. If it is, the function immediately returns an I/O error, preventing any further execution that could potentially cause harm. Tested via syzbot.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Collect command failures data only for known commands DEVX can issue a general command, which is not used by mlx5 driver. In case such command is failed, mlx5 is trying to collect the failure data, However, mlx5 doesn't create a storage for this command, since mlx5 doesn't use it. This lead to array-index-out-of-bounds error. Fix it by checking whether the command is known before collecting the failure data.

In the Linux kernel, the following vulnerability has been resolved: FS:JFS:UBSAN:array-index-out-of-bounds in dbAdjTree Syzkaller reported the following issue: UBSAN: array-index-out-of-bounds in fs/jfs/jfs_dmap.c:2867:6 index 196694 is out of range for type 's8[1365]' (aka 'signed char[1365]') CPU: 1 PID: 109 Comm: jfsCommit Not tainted 6.6.0-rc3-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/04/2023 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x1e7/0x2d0 lib/dump_stack.c:106 ubsan_epilogue lib/ubsan.c:217 [inline] __ubsan_handle_out_of_bounds+0x11c/0x150 lib/ubsan.c:348 dbAdjTree+0x474/0x4f0 fs/jfs/jfs_dmap.c:2867 dbJoin+0x210/0x2d0 fs/jfs/jfs_dmap.c:2834 dbFreeBits+0x4eb/0xda0 fs/jfs/jfs_dmap.c:2331 dbFreeDmap fs/jfs/jfs_dmap.c:2080 [inline] dbFree+0x343/0x650 fs/jfs/jfs_dmap.c:402 txFreeMap+0x798/0xd50 fs/jfs/jfs_txnmgr.c:2534 txUpdateMap+0x342/0x9e0 txLazyCommit fs/jfs/jfs_txnmgr.c:2664 [inline] jfs_lazycommit+0x47a/0xb70 fs/jfs/jfs_txnmgr.c:2732 kthread+0x2d3/0x370 kernel/kthread.c:388 ret_from_fork+0x48/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x11/0x20 arch/x86/entry/entry_64.S:304 </TASK> ================================================================================ Kernel panic - not syncing: UBSAN: panic_on_warn set ... CPU: 1 PID: 109 Comm: jfsCommit Not tainted 6.6.0-rc3-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/04/2023 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x1e7/0x2d0 lib/dump_stack.c:106 panic+0x30f/0x770 kernel/panic.c:340 check_panic_on_warn+0x82/0xa0 kernel/panic.c:236 ubsan_epilogue lib/ubsan.c:223 [inline] __ubsan_handle_out_of_bounds+0x13c/0x150 lib/ubsan.c:348 dbAdjTree+0x474/0x4f0 fs/jfs/jfs_dmap.c:2867 dbJoin+0x210/0x2d0 fs/jfs/jfs_dmap.c:2834 dbFreeBits+0x4eb/0xda0 fs/jfs/jfs_dmap.c:2331 dbFreeDmap fs/jfs/jfs_dmap.c:2080 [inline] dbFree+0x343/0x650 fs/jfs/jfs_dmap.c:402 txFreeMap+0x798/0xd50 fs/jfs/jfs_txnmgr.c:2534 txUpdateMap+0x342/0x9e0 txLazyCommit fs/jfs/jfs_txnmgr.c:2664 [inline] jfs_lazycommit+0x47a/0xb70 fs/jfs/jfs_txnmgr.c:2732 kthread+0x2d3/0x370 kernel/kthread.c:388 ret_from_fork+0x48/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x11/0x20 arch/x86/entry/entry_64.S:304 </TASK> Kernel Offset: disabled Rebooting in 86400 seconds.. The issue is caused when the value of lp becomes greater than CTLTREESIZE which is the max size of stree. Adding a simple check solves this issue. Dave: As the function returns a void, good error handling would require a more intrusive code reorganization, so I modified Osama's patch at use WARN_ON_ONCE for lack of a cleaner option. The patch is tested via syzbot.

In the Linux kernel, the following vulnerability has been resolved: net: hns3: fix out-of-bounds access may occur when coalesce info is read via debugfs The hns3 driver define an array of string to show the coalesce info, but if the kernel adds a new mode or a new state, out-of-bounds access may occur when coalesce info is read via debugfs, this patch fix the problem.

In the Linux kernel, the following vulnerability has been resolved: jfs: fix array-index-out-of-bounds in dbFindLeaf Currently while searching for dmtree_t for sufficient free blocks there is an array out of bounds while getting element in tp->dm_stree. To add the required check for out of bound we first need to determine the type of dmtree. Thus added an extra parameter to dbFindLeaf so that the type of tree can be determined and the required check can be applied.